W: http://www.arm.linux.org.uk/
S: Maintained
F: arch/arm/mach-ebsa110/
-F: drivers/net/arm/am79c961a.*
+F: drivers/net/ethernet/amd/am79c961a.*
ARM/EZX SMARTPHONES (A780, A910, A1200, E680, ROKR E2 and ROKR E6)
M: Daniel Ribeiro <drwyrm@gmail.com>
M: Don Fry <pcnet32@frontier.com>
L: netdev@vger.kernel.org
S: Maintained
-F: drivers/net/pcnet32.c
+F: drivers/net/ethernet/amd/pcnet32.c
PCRYPT PARALLEL CRYPTO ENGINE
M: Steffen Klassert <steffen.klassert@secunet.com>
To compile this driver as a module, choose M here: the module
will be called bmac.
-config ARIADNE
- tristate "Ariadne support"
- depends on ZORRO
- help
- If you have a Village Tronic Ariadne Ethernet adapter, say Y.
- Otherwise, say N.
-
- To compile this driver as a module, choose M here: the module
- will be called ariadne.
-
-config A2065
- tristate "A2065 support"
- depends on ZORRO
- select CRC32
- help
- If you have a Commodore A2065 Ethernet adapter, say Y. Otherwise,
- say N.
-
- To compile this driver as a module, choose M here: the module
- will be called a2065.
-
config HYDRA
tristate "Hydra support"
depends on ZORRO
say Y and read the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
-config MVME147_NET
- tristate "MVME147 (Lance) Ethernet support"
- depends on MVME147
- select CRC32
- help
- Support for the on-board Ethernet interface on the Motorola MVME147
- single-board computer. Say Y here to include the
- driver for this chip in your kernel.
- To compile this driver as a module, choose M here.
-
config MVME16x_NET
tristate "MVME16x Ethernet support"
depends on MVME16x
in your kernel.
To compile this driver as a module, choose M here.
-config ATARILANCE
- tristate "Atari Lance support"
- depends on ATARI
- help
- Say Y to include support for several Atari Ethernet adapters based
- on the AMD Lance chipset: RieblCard (with or without battery), or
- PAMCard VME (also the version by Rhotron, with different addresses).
-
-config SUN3LANCE
- tristate "Sun3/Sun3x on-board LANCE support"
- depends on SUN3 || SUN3X
- help
- Most Sun3 and Sun3x motherboards (including the 3/50, 3/60 and 3/80)
- featured an AMD Lance 10Mbit Ethernet controller on board; say Y
- here to compile in the Linux driver for this and enable Ethernet.
- General Linux information on the Sun 3 and 3x series (now
- discontinued) is at
- <http://www.angelfire.com/ca2/tech68k/sun3.html>.
-
- If you're not building a kernel for a Sun 3, say N.
-
config SUN3_82586
bool "Sun3 on-board Intel 82586 support"
depends on SUN3
that this driver does not support 82586-based adapters on additional
VME boards.
-config HPLANCE
- bool "HP on-board LANCE support"
- depends on DIO
- select CRC32
- help
- If you want to use the builtin "LANCE" Ethernet controller on an
- HP300 machine, say Y here.
-
config LASI_82596
tristate "Lasi ethernet"
depends on GSC
help
This is the driver for the onboard card of the Xtensa XT2000 board.
-config MIPS_AU1X00_ENET
- tristate "MIPS AU1000 Ethernet support"
- depends on MIPS_ALCHEMY
- select PHYLIB
- select CRC32
- help
- If you have an Alchemy Semi AU1X00 based system
- say Y. Otherwise, say N.
-
config SGI_IOC3_ETH
bool "SGI IOC3 Ethernet"
depends on PCI && SGI_IP27
This driver supporting CPUs are:
- SH7710, SH7712, SH7763, SH7619, SH7724, and SH7757.
-config SUNLANCE
- tristate "Sun LANCE support"
- depends on SBUS
- select CRC32
- help
- This driver supports the "le" interface present on all 32-bit Sparc
- systems, on some older Ultra systems and as an Sbus option. These
- cards are based on the AMD Lance chipset, which is better known
- via the NE2100 cards.
-
- To compile this driver as a module, choose M here: the module
- will be called sunlance.
-
config HAPPYMEAL
tristate "Sun Happy Meal 10/100baseT support"
depends on SBUS || PCI
To compile this driver as a module, choose M here. The module
will be called 3c527.
-config LANCE
- tristate "AMD LANCE and PCnet (AT1500 and NE2100) support"
- depends on ISA && ISA_DMA_API
- help
- If you have a network (Ethernet) card of this type, say Y and read
- the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>. Some LinkSys cards are
- of this type.
-
- To compile this driver as a module, choose M here: the module
- will be called lance. This is recommended.
-
config NET_VENDOR_SMC
bool "Western Digital/SMC cards"
depends on ISA || MCA || EISA || MAC
To compile this driver as a module, choose M here. The module
will be called ni52.
-config NI65
- tristate "NI6510 support"
- depends on NET_VENDOR_RACAL && ISA && ISA_DMA_API
- help
- If you have a network (Ethernet) card of this type, say Y and read
- the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here. The module
- will be called ni65.
-
config DNET
tristate "Dave ethernet support (DNET)"
depends on NET_ETHERNET && HAS_IOMEM
To compile this driver as a module, choose M here. The module
will be called at1700.
-config DEPCA
- tristate "DEPCA, DE10x, DE200, DE201, DE202, DE422 support"
- depends on ISA || EISA || MCA
- select CRC32
- ---help---
- If you have a network (Ethernet) card of this type, say Y and read
- the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto> as well as
- <file:drivers/net/depca.c>.
-
- To compile this driver as a module, choose M here. The module
- will be called depca.
-
config HP100
tristate "HP 10/100VG PCLAN (ISA, EISA, PCI) support"
depends on ISA || EISA || PCI
will be asked for your specific card in the following questions. If
you are unsure, say Y.
-config PCNET32
- tristate "AMD PCnet32 PCI support"
- depends on NET_PCI && PCI
- select CRC32
- select MII
- help
- If you have a PCnet32 or PCnetPCI based network (Ethernet) card,
- answer Y here and read the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here. The module
- will be called pcnet32.
-
-config AMD8111_ETH
- tristate "AMD 8111 (new PCI lance) support"
- depends on NET_PCI && PCI
- select CRC32
- select MII
- help
- If you have an AMD 8111-based PCI lance ethernet card,
- answer Y here and read the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here. The module
- will be called amd8111e.
-
config ADAPTEC_STARFIRE
tristate "Adaptec Starfire/DuraLAN support"
depends on NET_PCI && PCI
Say Y here if you have an Seeq based Ethernet network card. This is
used in many Silicon Graphics machines.
-config DECLANCE
- tristate "DEC LANCE ethernet controller support"
- depends on MACH_DECSTATION
- select CRC32
- help
- This driver is for the series of Ethernet controllers produced by
- DEC (now Compaq) based on the AMD Lance chipset, including the
- DEPCA series. (This chipset is better known via the NE2100 cards.)
-
config FEC
bool "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
depends on M523x || M527x || M5272 || M528x || M520x || M532x || \
obj-$(CONFIG_ROADRUNNER) += rrunner.o
obj-$(CONFIG_HAPPYMEAL) += sunhme.o
-obj-$(CONFIG_SUNLANCE) += sunlance.o
obj-$(CONFIG_SUNQE) += sunqe.o
obj-$(CONFIG_SUNBMAC) += sunbmac.o
obj-$(CONFIG_SUNGEM) += sungem.o sungem_phy.o
obj-$(CONFIG_BMAC) += bmac.o
obj-$(CONFIG_NE2K_PCI) += ne2k-pci.o 8390.o
-obj-$(CONFIG_PCNET32) += pcnet32.o
obj-$(CONFIG_E100) += e100.o
obj-$(CONFIG_TLAN) += tlan.o
obj-$(CONFIG_EPIC100) += epic100.o
obj-$(CONFIG_MACVTAP) += macvtap.o
obj-$(CONFIG_DE600) += de600.o
obj-$(CONFIG_DE620) += de620.o
-obj-$(CONFIG_LANCE) += lance.o
obj-$(CONFIG_SUN3_82586) += sun3_82586.o
-obj-$(CONFIG_SUN3LANCE) += sun3lance.o
obj-$(CONFIG_DEFXX) += defxx.o
obj-$(CONFIG_SGISEEQ) += sgiseeq.o
obj-$(CONFIG_SGI_O2MACE_ETH) += meth.o
obj-$(CONFIG_8139TOO) += 8139too.o
obj-$(CONFIG_ZNET) += znet.o
obj-$(CONFIG_CPMAC) += cpmac.o
-obj-$(CONFIG_DEPCA) += depca.o
obj-$(CONFIG_EWRK3) += ewrk3.o
obj-$(CONFIG_ATP) += atp.o
obj-$(CONFIG_NI5010) += ni5010.o
obj-$(CONFIG_NI52) += ni52.o
-obj-$(CONFIG_NI65) += ni65.o
obj-$(CONFIG_ELPLUS) += 3c505.o
obj-$(CONFIG_AC3200) += ac3200.o 8390.o
obj-$(CONFIG_APRICOT) += 82596.o
obj-$(CONFIG_ETH16I) += eth16i.o
obj-$(CONFIG_ZORRO8390) += zorro8390.o
-obj-$(CONFIG_HPLANCE) += hplance.o 7990.o
-obj-$(CONFIG_MVME147_NET) += mvme147.o 7990.o
obj-$(CONFIG_EQUALIZER) += eql.o
obj-$(CONFIG_KORINA) += korina.o
obj-$(CONFIG_MIPS_JAZZ_SONIC) += jazzsonic.o
-obj-$(CONFIG_MIPS_AU1X00_ENET) += au1000_eth.o
obj-$(CONFIG_MIPS_SIM_NET) += mipsnet.o
obj-$(CONFIG_SGI_IOC3_ETH) += ioc3-eth.o
-obj-$(CONFIG_DECLANCE) += declance.o
-obj-$(CONFIG_ATARILANCE) += atarilance.o
-obj-$(CONFIG_A2065) += a2065.o
obj-$(CONFIG_HYDRA) += hydra.o
-obj-$(CONFIG_ARIADNE) += ariadne.o
obj-$(CONFIG_CS89x0) += cs89x0.o
obj-$(CONFIG_MACSONIC) += macsonic.o
obj-$(CONFIG_MACMACE) += macmace.o
obj-$(CONFIG_NET_NETX) += netx-eth.o
obj-$(CONFIG_DL2K) += dl2k.o
obj-$(CONFIG_R8169) += r8169.o
-obj-$(CONFIG_AMD8111_ETH) += amd8111e.o
obj-$(CONFIG_IBMVETH) += ibmveth.o
obj-$(CONFIG_S2IO) += s2io.o
obj-$(CONFIG_VXGE) += vxge/
# Acorn Network device configuration
# These are for Acorn's Expansion card network interfaces
#
-config ARM_AM79C961A
- bool "ARM EBSA110 AM79C961A support"
- depends on ARM && ARCH_EBSA110
- select CRC32
- help
- If you wish to compile a kernel for the EBSA-110, then you should
- always answer Y to this.
config ARM_ETHER1
tristate "Acorn Ether1 support"
# Makefile for the ARM network device drivers
#
-obj-$(CONFIG_ARM_AM79C961A) += am79c961a.o
obj-$(CONFIG_ARM_ETHERH) += etherh.o
obj-$(CONFIG_ARM_ETHER3) += ether3.o
obj-$(CONFIG_ARM_ETHER1) += ether1.o
if ETHERNET
source "drivers/net/ethernet/3com/Kconfig"
+source "drivers/net/ethernet/amd/Kconfig"
endif # ETHERNET
#
obj-$(CONFIG_NET_VENDOR_3COM) += 3com/
+obj-$(CONFIG_NET_VENDOR_AMD) += amd/
--- /dev/null
+#
+# AMD network device configuration
+#
+
+config NET_VENDOR_AMD
+ bool "AMD devices"
+ depends on DIO || MACH_DECSTATION || MVME147 || ATARI || SUN3 || \
+ SUN3X || SBUS || PCI || ZORRO || (ISA && ISA_DMA_API) || \
+ (ARM && ARCH_EBSA110) || ISA || EISA || MCA || PCMCIA
+ ---help---
+ If you have a network (Ethernet) chipset belonging to this class,
+ say Y.
+
+ Note that the answer to this question does not directly affect
+ the kernel: saying N will just case the configurator to skip all
+ the questions regarding AMD chipsets. If you say Y, you will be asked
+ for your specific chipset/driver in the following questions.
+
+if NET_VENDOR_AMD
+
+config A2065
+ tristate "A2065 support"
+ depends on ZORRO
+ select CRC32
+ ---help---
+ If you have a Commodore A2065 Ethernet adapter, say Y. Otherwise,
+ say N.
+
+ To compile this driver as a module, choose M here: the module
+ will be called a2065.
+
+config AMD8111_ETH
+ tristate "AMD 8111 (new PCI LANCE) support"
+ depends on PCI
+ select CRC32
+ select MII
+ ---help---
+ If you have an AMD 8111-based PCI LANCE ethernet card,
+ answer Y here and read the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called amd8111e.
+
+config LANCE
+ tristate "AMD LANCE and PCnet (AT1500 and NE2100) support"
+ depends on ISA && ISA_DMA_API
+ ---help---
+ If you have a network (Ethernet) card of this type, say Y and read
+ the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>. Some LinkSys cards are
+ of this type.
+
+ To compile this driver as a module, choose M here: the module
+ will be called lance. This is recommended.
+
+config PCNET32
+ tristate "AMD PCnet32 PCI support"
+ depends on PCI
+ select CRC32
+ select MII
+ ---help---
+ If you have a PCnet32 or PCnetPCI based network (Ethernet) card,
+ answer Y here and read the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called pcnet32.
+
+config ARIADNE
+ tristate "Ariadne support"
+ depends on ZORRO
+ ---help---
+ If you have a Village Tronic Ariadne Ethernet adapter, say Y.
+ Otherwise, say N.
+
+ To compile this driver as a module, choose M here: the module
+ will be called ariadne.
+
+config ARM_AM79C961A
+ bool "ARM EBSA110 AM79C961A support"
+ depends on ARM && ARCH_EBSA110
+ select CRC32
+ ---help---
+ If you wish to compile a kernel for the EBSA-110, then you should
+ always answer Y to this.
+
+config ATARILANCE
+ tristate "Atari LANCE support"
+ depends on ATARI
+ ---help---
+ Say Y to include support for several Atari Ethernet adapters based
+ on the AMD LANCE chipset: RieblCard (with or without battery), or
+ PAMCard VME (also the version by Rhotron, with different addresses).
+
+config DECLANCE
+ tristate "DEC LANCE ethernet controller support"
+ depends on MACH_DECSTATION
+ select CRC32
+ ---help---
+ This driver is for the series of Ethernet controllers produced by
+ DEC (now Compaq) based on the AMD LANCE chipset, including the
+ DEPCA series. (This chipset is better known via the NE2100 cards.)
+
+config DEPCA
+ tristate "DEPCA, DE10x, DE200, DE201, DE202, DE422 support"
+ depends on (ISA || EISA || MCA)
+ select CRC32
+ ---help---
+ If you have a network (Ethernet) card of this type, say Y and read
+ the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto> as well as
+ <file:drivers/net/depca.c>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called depca.
+
+config HPLANCE
+ bool "HP on-board LANCE support"
+ depends on DIO
+ select CRC32
+ ---help---
+ If you want to use the builtin "LANCE" Ethernet controller on an
+ HP300 machine, say Y here.
+
+config MIPS_AU1X00_ENET
+ tristate "MIPS AU1000 Ethernet support"
+ depends on MIPS_ALCHEMY
+ select PHYLIB
+ select CRC32
+ ---help---
+ If you have an Alchemy Semi AU1X00 based system
+ say Y. Otherwise, say N.
+
+config MVME147_NET
+ tristate "MVME147 (LANCE) Ethernet support"
+ depends on MVME147
+ select CRC32
+ ---help---
+ Support for the on-board Ethernet interface on the Motorola MVME147
+ single-board computer. Say Y here to include the
+ driver for this chip in your kernel.
+ To compile this driver as a module, choose M here.
+
+config PCMCIA_NMCLAN
+ tristate "New Media PCMCIA support"
+ depends on PCMCIA
+ help
+ Say Y here if you intend to attach a New Media Ethernet or LiveWire
+ PCMCIA (PC-card) Ethernet card to your computer.
+
+ To compile this driver as a module, choose M here: the module will be
+ called nmclan_cs. If unsure, say N.
+
+config NI65
+ tristate "NI6510 support"
+ depends on ISA && ISA_DMA_API
+ ---help---
+ If you have a network (Ethernet) card of this type, say Y and read
+ the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called ni65.
+
+config SUN3LANCE
+ tristate "Sun3/Sun3x on-board LANCE support"
+ depends on (SUN3 || SUN3X)
+ ---help---
+ Most Sun3 and Sun3x motherboards (including the 3/50, 3/60 and 3/80)
+ featured an AMD LANCE 10Mbit Ethernet controller on board; say Y
+ here to compile in the Linux driver for this and enable Ethernet.
+ General Linux information on the Sun 3 and 3x series (now
+ discontinued) is at
+ <http://www.angelfire.com/ca2/tech68k/sun3.html>.
+
+ If you're not building a kernel for a Sun 3, say N.
+
+config SUNLANCE
+ tristate "Sun LANCE support"
+ depends on SBUS
+ select CRC32
+ ---help---
+ This driver supports the "le" interface present on all 32-bit Sparc
+ systems, on some older Ultra systems and as an Sbus option. These
+ cards are based on the AMD LANCE chipset, which is better known
+ via the NE2100 cards.
+
+ To compile this driver as a module, choose M here: the module
+ will be called sunlance.
+
+endif # NET_VENDOR_AMD
--- /dev/null
+#
+# Makefile for the AMD network device drivers.
+#
+
+obj-$(CONFIG_A2065) += a2065.o
+obj-$(CONFIG_AMD8111_ETH) += amd8111e.o
+obj-$(CONFIG_ARM_AM79C961A) += am79c961a.o
+obj-$(CONFIG_ARIADNE) += ariadne.o
+obj-$(CONFIG_ATARILANCE) += atarilance.o
+obj-$(CONFIG_DECLANCE) += declance.o
+obj-$(CONFIG_DEPCA) += depca.o
+obj-$(CONFIG_HPLANCE) += hplance.o 7990.o
+obj-$(CONFIG_LANCE) += lance.o
+obj-$(CONFIG_MIPS_AU1X00_ENET) += au1000_eth.o
+obj-$(CONFIG_MVME147_NET) += mvme147.o 7990.o
+obj-$(CONFIG_PCMCIA_NMCLAN) += nmclan_cs.o
+obj-$(CONFIG_NI65) += ni65.o
+obj-$(CONFIG_PCNET32) += pcnet32.o
+obj-$(CONFIG_SUN3LANCE) += sun3lance.o
+obj-$(CONFIG_SUNLANCE) += sunlance.o
To compile this driver as a module, choose M here: the module will be
called pcnet_cs. If unsure, say N.
-config PCMCIA_NMCLAN
- tristate "New Media PCMCIA support"
- help
- Say Y here if you intend to attach a New Media Ethernet or LiveWire
- PCMCIA (PC-card) Ethernet card to your computer.
-
- To compile this driver as a module, choose M here: the module will be
- called nmclan_cs. If unsure, say N.
-
config PCMCIA_SMC91C92
tristate "SMC 91Cxx PCMCIA support"
select CRC32
# 16-bit client drivers
obj-$(CONFIG_PCMCIA_FMVJ18X) += fmvj18x_cs.o
-obj-$(CONFIG_PCMCIA_NMCLAN) += nmclan_cs.o
obj-$(CONFIG_PCMCIA_PCNET) += pcnet_cs.o
obj-$(CONFIG_PCMCIA_SMC91C92) += smc91c92_cs.o
obj-$(CONFIG_PCMCIA_XIRC2PS) += xirc2ps_cs.o
git.samba.org / sfrench / cifs-2.6.git / commitdiff