1 /*******************************************************************************
2 This is the driver for the ST MAC 10/100/1000 on-chip Ethernet controllers.
3 ST Ethernet IPs are built around a Synopsys IP Core.
5 Copyright(C) 2007-2011 STMicroelectronics Ltd
7 This program is free software; you can redistribute it and/or modify it
8 under the terms and conditions of the GNU General Public License,
9 version 2, as published by the Free Software Foundation.
11 This program is distributed in the hope it will be useful, but WITHOUT
12 ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
13 FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
16 The full GNU General Public License is included in this distribution in
17 the file called "COPYING".
19 Author: Giuseppe Cavallaro <peppe.cavallaro@st.com>
21 Documentation available at:
22 http://www.stlinux.com
24 https://bugzilla.stlinux.com/
25 *******************************************************************************/
27 #include <linux/clk.h>
28 #include <linux/kernel.h>
29 #include <linux/interrupt.h>
31 #include <linux/tcp.h>
32 #include <linux/skbuff.h>
33 #include <linux/ethtool.h>
34 #include <linux/if_ether.h>
35 #include <linux/crc32.h>
36 #include <linux/mii.h>
38 #include <linux/if_vlan.h>
39 #include <linux/dma-mapping.h>
40 #include <linux/slab.h>
41 #include <linux/prefetch.h>
42 #include <linux/pinctrl/consumer.h>
43 #ifdef CONFIG_DEBUG_FS
44 #include <linux/debugfs.h>
45 #include <linux/seq_file.h>
46 #endif /* CONFIG_DEBUG_FS */
47 #include <linux/net_tstamp.h>
48 #include "stmmac_ptp.h"
50 #include <linux/reset.h>
51 #include <linux/of_mdio.h>
52 #include "dwmac1000.h"
54 #define STMMAC_ALIGN(x) L1_CACHE_ALIGN(x)
55 #define TSO_MAX_BUFF_SIZE (SZ_16K - 1)
57 /* Module parameters */
59 static int watchdog = TX_TIMEO;
60 module_param(watchdog, int, S_IRUGO | S_IWUSR);
61 MODULE_PARM_DESC(watchdog, "Transmit timeout in milliseconds (default 5s)");
63 static int debug = -1;
64 module_param(debug, int, S_IRUGO | S_IWUSR);
65 MODULE_PARM_DESC(debug, "Message Level (-1: default, 0: no output, 16: all)");
67 static int phyaddr = -1;
68 module_param(phyaddr, int, S_IRUGO);
69 MODULE_PARM_DESC(phyaddr, "Physical device address");
71 #define STMMAC_TX_THRESH (DMA_TX_SIZE / 4)
72 #define STMMAC_RX_THRESH (DMA_RX_SIZE / 4)
74 static int flow_ctrl = FLOW_OFF;
75 module_param(flow_ctrl, int, S_IRUGO | S_IWUSR);
76 MODULE_PARM_DESC(flow_ctrl, "Flow control ability [on/off]");
78 static int pause = PAUSE_TIME;
79 module_param(pause, int, S_IRUGO | S_IWUSR);
80 MODULE_PARM_DESC(pause, "Flow Control Pause Time");
83 static int tc = TC_DEFAULT;
84 module_param(tc, int, S_IRUGO | S_IWUSR);
85 MODULE_PARM_DESC(tc, "DMA threshold control value");
87 #define DEFAULT_BUFSIZE 1536
88 static int buf_sz = DEFAULT_BUFSIZE;
89 module_param(buf_sz, int, S_IRUGO | S_IWUSR);
90 MODULE_PARM_DESC(buf_sz, "DMA buffer size");
92 #define STMMAC_RX_COPYBREAK 256
94 static const u32 default_msg_level = (NETIF_MSG_DRV | NETIF_MSG_PROBE |
95 NETIF_MSG_LINK | NETIF_MSG_IFUP |
96 NETIF_MSG_IFDOWN | NETIF_MSG_TIMER);
98 #define STMMAC_DEFAULT_LPI_TIMER 1000
99 static int eee_timer = STMMAC_DEFAULT_LPI_TIMER;
100 module_param(eee_timer, int, S_IRUGO | S_IWUSR);
101 MODULE_PARM_DESC(eee_timer, "LPI tx expiration time in msec");
102 #define STMMAC_LPI_T(x) (jiffies + msecs_to_jiffies(x))
104 /* By default the driver will use the ring mode to manage tx and rx descriptors,
105 * but allow user to force to use the chain instead of the ring
107 static unsigned int chain_mode;
108 module_param(chain_mode, int, S_IRUGO);
109 MODULE_PARM_DESC(chain_mode, "To use chain instead of ring mode");
111 static irqreturn_t stmmac_interrupt(int irq, void *dev_id);
113 #ifdef CONFIG_DEBUG_FS
114 static int stmmac_init_fs(struct net_device *dev);
115 static void stmmac_exit_fs(struct net_device *dev);
118 #define STMMAC_COAL_TIMER(x) (jiffies + usecs_to_jiffies(x))
121 * stmmac_verify_args - verify the driver parameters.
122 * Description: it checks the driver parameters and set a default in case of
125 static void stmmac_verify_args(void)
127 if (unlikely(watchdog < 0))
129 if (unlikely((buf_sz < DEFAULT_BUFSIZE) || (buf_sz > BUF_SIZE_16KiB)))
130 buf_sz = DEFAULT_BUFSIZE;
131 if (unlikely(flow_ctrl > 1))
132 flow_ctrl = FLOW_AUTO;
133 else if (likely(flow_ctrl < 0))
134 flow_ctrl = FLOW_OFF;
135 if (unlikely((pause < 0) || (pause > 0xffff)))
138 eee_timer = STMMAC_DEFAULT_LPI_TIMER;
142 * stmmac_disable_all_queues - Disable all queues
143 * @priv: driver private structure
145 static void stmmac_disable_all_queues(struct stmmac_priv *priv)
147 u32 rx_queues_cnt = priv->plat->rx_queues_to_use;
150 for (queue = 0; queue < rx_queues_cnt; queue++) {
151 struct stmmac_rx_queue *rx_q = &priv->rx_queue[queue];
153 napi_disable(&rx_q->napi);
158 * stmmac_enable_all_queues - Enable all queues
159 * @priv: driver private structure
161 static void stmmac_enable_all_queues(struct stmmac_priv *priv)
163 u32 rx_queues_cnt = priv->plat->rx_queues_to_use;
166 for (queue = 0; queue < rx_queues_cnt; queue++) {
167 struct stmmac_rx_queue *rx_q = &priv->rx_queue[queue];
169 napi_enable(&rx_q->napi);
174 * stmmac_stop_all_queues - Stop all queues
175 * @priv: driver private structure
177 static void stmmac_stop_all_queues(struct stmmac_priv *priv)
179 u32 tx_queues_cnt = priv->plat->tx_queues_to_use;
182 for (queue = 0; queue < tx_queues_cnt; queue++)
183 netif_tx_stop_queue(netdev_get_tx_queue(priv->dev, queue));
187 * stmmac_start_all_queues - Start all queues
188 * @priv: driver private structure
190 static void stmmac_start_all_queues(struct stmmac_priv *priv)
192 u32 tx_queues_cnt = priv->plat->tx_queues_to_use;
195 for (queue = 0; queue < tx_queues_cnt; queue++)
196 netif_tx_start_queue(netdev_get_tx_queue(priv->dev, queue));
200 * stmmac_clk_csr_set - dynamically set the MDC clock
201 * @priv: driver private structure
202 * Description: this is to dynamically set the MDC clock according to the csr
205 * If a specific clk_csr value is passed from the platform
206 * this means that the CSR Clock Range selection cannot be
207 * changed at run-time and it is fixed (as reported in the driver
208 * documentation). Viceversa the driver will try to set the MDC
209 * clock dynamically according to the actual clock input.
211 static void stmmac_clk_csr_set(struct stmmac_priv *priv)
215 clk_rate = clk_get_rate(priv->plat->stmmac_clk);
217 /* Platform provided default clk_csr would be assumed valid
218 * for all other cases except for the below mentioned ones.
219 * For values higher than the IEEE 802.3 specified frequency
220 * we can not estimate the proper divider as it is not known
221 * the frequency of clk_csr_i. So we do not change the default
224 if (!(priv->clk_csr & MAC_CSR_H_FRQ_MASK)) {
225 if (clk_rate < CSR_F_35M)
226 priv->clk_csr = STMMAC_CSR_20_35M;
227 else if ((clk_rate >= CSR_F_35M) && (clk_rate < CSR_F_60M))
228 priv->clk_csr = STMMAC_CSR_35_60M;
229 else if ((clk_rate >= CSR_F_60M) && (clk_rate < CSR_F_100M))
230 priv->clk_csr = STMMAC_CSR_60_100M;
231 else if ((clk_rate >= CSR_F_100M) && (clk_rate < CSR_F_150M))
232 priv->clk_csr = STMMAC_CSR_100_150M;
233 else if ((clk_rate >= CSR_F_150M) && (clk_rate < CSR_F_250M))
234 priv->clk_csr = STMMAC_CSR_150_250M;
235 else if ((clk_rate >= CSR_F_250M) && (clk_rate < CSR_F_300M))
236 priv->clk_csr = STMMAC_CSR_250_300M;
239 if (priv->plat->has_sun8i) {
240 if (clk_rate > 160000000)
241 priv->clk_csr = 0x03;
242 else if (clk_rate > 80000000)
243 priv->clk_csr = 0x02;
244 else if (clk_rate > 40000000)
245 priv->clk_csr = 0x01;
251 static void print_pkt(unsigned char *buf, int len)
253 pr_debug("len = %d byte, buf addr: 0x%p\n", len, buf);
254 print_hex_dump_bytes("", DUMP_PREFIX_OFFSET, buf, len);
257 static inline u32 stmmac_tx_avail(struct stmmac_priv *priv, u32 queue)
259 struct stmmac_tx_queue *tx_q = &priv->tx_queue[queue];
262 if (tx_q->dirty_tx > tx_q->cur_tx)
263 avail = tx_q->dirty_tx - tx_q->cur_tx - 1;
265 avail = DMA_TX_SIZE - tx_q->cur_tx + tx_q->dirty_tx - 1;
271 * stmmac_rx_dirty - Get RX queue dirty
272 * @priv: driver private structure
273 * @queue: RX queue index
275 static inline u32 stmmac_rx_dirty(struct stmmac_priv *priv, u32 queue)
277 struct stmmac_rx_queue *rx_q = &priv->rx_queue[queue];
280 if (rx_q->dirty_rx <= rx_q->cur_rx)
281 dirty = rx_q->cur_rx - rx_q->dirty_rx;
283 dirty = DMA_RX_SIZE - rx_q->dirty_rx + rx_q->cur_rx;
289 * stmmac_hw_fix_mac_speed - callback for speed selection
290 * @priv: driver private structure
291 * Description: on some platforms (e.g. ST), some HW system configuration
292 * registers have to be set according to the link speed negotiated.
294 static inline void stmmac_hw_fix_mac_speed(struct stmmac_priv *priv)
296 struct net_device *ndev = priv->dev;
297 struct phy_device *phydev = ndev->phydev;
299 if (likely(priv->plat->fix_mac_speed))
300 priv->plat->fix_mac_speed(priv->plat->bsp_priv, phydev->speed);
304 * stmmac_enable_eee_mode - check and enter in LPI mode
305 * @priv: driver private structure
306 * Description: this function is to verify and enter in LPI mode in case of
309 static void stmmac_enable_eee_mode(struct stmmac_priv *priv)
311 u32 tx_cnt = priv->plat->tx_queues_to_use;
314 /* check if all TX queues have the work finished */
315 for (queue = 0; queue < tx_cnt; queue++) {
316 struct stmmac_tx_queue *tx_q = &priv->tx_queue[queue];
318 if (tx_q->dirty_tx != tx_q->cur_tx)
319 return; /* still unfinished work */
322 /* Check and enter in LPI mode */
323 if (!priv->tx_path_in_lpi_mode)
324 priv->hw->mac->set_eee_mode(priv->hw,
325 priv->plat->en_tx_lpi_clockgating);
329 * stmmac_disable_eee_mode - disable and exit from LPI mode
330 * @priv: driver private structure
331 * Description: this function is to exit and disable EEE in case of
332 * LPI state is true. This is called by the xmit.
334 void stmmac_disable_eee_mode(struct stmmac_priv *priv)
336 priv->hw->mac->reset_eee_mode(priv->hw);
337 del_timer_sync(&priv->eee_ctrl_timer);
338 priv->tx_path_in_lpi_mode = false;
342 * stmmac_eee_ctrl_timer - EEE TX SW timer.
345 * if there is no data transfer and if we are not in LPI state,
346 * then MAC Transmitter can be moved to LPI state.
348 static void stmmac_eee_ctrl_timer(unsigned long arg)
350 struct stmmac_priv *priv = (struct stmmac_priv *)arg;
352 stmmac_enable_eee_mode(priv);
353 mod_timer(&priv->eee_ctrl_timer, STMMAC_LPI_T(eee_timer));
357 * stmmac_eee_init - init EEE
358 * @priv: driver private structure
360 * if the GMAC supports the EEE (from the HW cap reg) and the phy device
361 * can also manage EEE, this function enable the LPI state and start related
364 bool stmmac_eee_init(struct stmmac_priv *priv)
366 struct net_device *ndev = priv->dev;
370 /* Using PCS we cannot dial with the phy registers at this stage
371 * so we do not support extra feature like EEE.
373 if ((priv->hw->pcs == STMMAC_PCS_RGMII) ||
374 (priv->hw->pcs == STMMAC_PCS_TBI) ||
375 (priv->hw->pcs == STMMAC_PCS_RTBI))
378 /* MAC core supports the EEE feature. */
379 if (priv->dma_cap.eee) {
380 int tx_lpi_timer = priv->tx_lpi_timer;
382 /* Check if the PHY supports EEE */
383 if (phy_init_eee(ndev->phydev, 1)) {
384 /* To manage at run-time if the EEE cannot be supported
385 * anymore (for example because the lp caps have been
387 * In that case the driver disable own timers.
389 spin_lock_irqsave(&priv->lock, flags);
390 if (priv->eee_active) {
391 netdev_dbg(priv->dev, "disable EEE\n");
392 del_timer_sync(&priv->eee_ctrl_timer);
393 priv->hw->mac->set_eee_timer(priv->hw, 0,
396 priv->eee_active = 0;
397 spin_unlock_irqrestore(&priv->lock, flags);
400 /* Activate the EEE and start timers */
401 spin_lock_irqsave(&priv->lock, flags);
402 if (!priv->eee_active) {
403 priv->eee_active = 1;
404 setup_timer(&priv->eee_ctrl_timer,
405 stmmac_eee_ctrl_timer,
406 (unsigned long)priv);
407 mod_timer(&priv->eee_ctrl_timer,
408 STMMAC_LPI_T(eee_timer));
410 priv->hw->mac->set_eee_timer(priv->hw,
411 STMMAC_DEFAULT_LIT_LS,
414 /* Set HW EEE according to the speed */
415 priv->hw->mac->set_eee_pls(priv->hw, ndev->phydev->link);
418 spin_unlock_irqrestore(&priv->lock, flags);
420 netdev_dbg(priv->dev, "Energy-Efficient Ethernet initialized\n");
426 /* stmmac_get_tx_hwtstamp - get HW TX timestamps
427 * @priv: driver private structure
428 * @p : descriptor pointer
429 * @skb : the socket buffer
431 * This function will read timestamp from the descriptor & pass it to stack.
432 * and also perform some sanity checks.
434 static void stmmac_get_tx_hwtstamp(struct stmmac_priv *priv,
435 struct dma_desc *p, struct sk_buff *skb)
437 struct skb_shared_hwtstamps shhwtstamp;
440 if (!priv->hwts_tx_en)
443 /* exit if skb doesn't support hw tstamp */
444 if (likely(!skb || !(skb_shinfo(skb)->tx_flags & SKBTX_IN_PROGRESS)))
447 /* check tx tstamp status */
448 if (priv->hw->desc->get_tx_timestamp_status(p)) {
449 /* get the valid tstamp */
450 ns = priv->hw->desc->get_timestamp(p, priv->adv_ts);
452 memset(&shhwtstamp, 0, sizeof(struct skb_shared_hwtstamps));
453 shhwtstamp.hwtstamp = ns_to_ktime(ns);
455 netdev_dbg(priv->dev, "get valid TX hw timestamp %llu\n", ns);
456 /* pass tstamp to stack */
457 skb_tstamp_tx(skb, &shhwtstamp);
463 /* stmmac_get_rx_hwtstamp - get HW RX timestamps
464 * @priv: driver private structure
465 * @p : descriptor pointer
466 * @np : next descriptor pointer
467 * @skb : the socket buffer
469 * This function will read received packet's timestamp from the descriptor
470 * and pass it to stack. It also perform some sanity checks.
472 static void stmmac_get_rx_hwtstamp(struct stmmac_priv *priv, struct dma_desc *p,
473 struct dma_desc *np, struct sk_buff *skb)
475 struct skb_shared_hwtstamps *shhwtstamp = NULL;
476 struct dma_desc *desc = p;
479 if (!priv->hwts_rx_en)
481 /* For GMAC4, the valid timestamp is from CTX next desc. */
482 if (priv->plat->has_gmac4)
485 /* Check if timestamp is available */
486 if (priv->hw->desc->get_rx_timestamp_status(desc, priv->adv_ts)) {
487 ns = priv->hw->desc->get_timestamp(desc, priv->adv_ts);
488 netdev_dbg(priv->dev, "get valid RX hw timestamp %llu\n", ns);
489 shhwtstamp = skb_hwtstamps(skb);
490 memset(shhwtstamp, 0, sizeof(struct skb_shared_hwtstamps));
491 shhwtstamp->hwtstamp = ns_to_ktime(ns);
493 netdev_dbg(priv->dev, "cannot get RX hw timestamp\n");
498 * stmmac_hwtstamp_ioctl - control hardware timestamping.
499 * @dev: device pointer.
500 * @ifr: An IOCTL specific structure, that can contain a pointer to
501 * a proprietary structure used to pass information to the driver.
503 * This function configures the MAC to enable/disable both outgoing(TX)
504 * and incoming(RX) packets time stamping based on user input.
506 * 0 on success and an appropriate -ve integer on failure.
508 static int stmmac_hwtstamp_ioctl(struct net_device *dev, struct ifreq *ifr)
510 struct stmmac_priv *priv = netdev_priv(dev);
511 struct hwtstamp_config config;
512 struct timespec64 now;
516 u32 ptp_over_ipv4_udp = 0;
517 u32 ptp_over_ipv6_udp = 0;
518 u32 ptp_over_ethernet = 0;
519 u32 snap_type_sel = 0;
520 u32 ts_master_en = 0;
525 if (!(priv->dma_cap.time_stamp || priv->adv_ts)) {
526 netdev_alert(priv->dev, "No support for HW time stamping\n");
527 priv->hwts_tx_en = 0;
528 priv->hwts_rx_en = 0;
533 if (copy_from_user(&config, ifr->ifr_data,
534 sizeof(struct hwtstamp_config)))
537 netdev_dbg(priv->dev, "%s config flags:0x%x, tx_type:0x%x, rx_filter:0x%x\n",
538 __func__, config.flags, config.tx_type, config.rx_filter);
540 /* reserved for future extensions */
544 if (config.tx_type != HWTSTAMP_TX_OFF &&
545 config.tx_type != HWTSTAMP_TX_ON)
549 switch (config.rx_filter) {
550 case HWTSTAMP_FILTER_NONE:
551 /* time stamp no incoming packet at all */
552 config.rx_filter = HWTSTAMP_FILTER_NONE;
555 case HWTSTAMP_FILTER_PTP_V1_L4_EVENT:
556 /* PTP v1, UDP, any kind of event packet */
557 config.rx_filter = HWTSTAMP_FILTER_PTP_V1_L4_EVENT;
558 /* take time stamp for all event messages */
559 if (priv->plat->has_gmac4)
560 snap_type_sel = PTP_GMAC4_TCR_SNAPTYPSEL_1;
562 snap_type_sel = PTP_TCR_SNAPTYPSEL_1;
564 ptp_over_ipv4_udp = PTP_TCR_TSIPV4ENA;
565 ptp_over_ipv6_udp = PTP_TCR_TSIPV6ENA;
568 case HWTSTAMP_FILTER_PTP_V1_L4_SYNC:
569 /* PTP v1, UDP, Sync packet */
570 config.rx_filter = HWTSTAMP_FILTER_PTP_V1_L4_SYNC;
571 /* take time stamp for SYNC messages only */
572 ts_event_en = PTP_TCR_TSEVNTENA;
574 ptp_over_ipv4_udp = PTP_TCR_TSIPV4ENA;
575 ptp_over_ipv6_udp = PTP_TCR_TSIPV6ENA;
578 case HWTSTAMP_FILTER_PTP_V1_L4_DELAY_REQ:
579 /* PTP v1, UDP, Delay_req packet */
580 config.rx_filter = HWTSTAMP_FILTER_PTP_V1_L4_DELAY_REQ;
581 /* take time stamp for Delay_Req messages only */
582 ts_master_en = PTP_TCR_TSMSTRENA;
583 ts_event_en = PTP_TCR_TSEVNTENA;
585 ptp_over_ipv4_udp = PTP_TCR_TSIPV4ENA;
586 ptp_over_ipv6_udp = PTP_TCR_TSIPV6ENA;
589 case HWTSTAMP_FILTER_PTP_V2_L4_EVENT:
590 /* PTP v2, UDP, any kind of event packet */
591 config.rx_filter = HWTSTAMP_FILTER_PTP_V2_L4_EVENT;
592 ptp_v2 = PTP_TCR_TSVER2ENA;
593 /* take time stamp for all event messages */
594 if (priv->plat->has_gmac4)
595 snap_type_sel = PTP_GMAC4_TCR_SNAPTYPSEL_1;
597 snap_type_sel = PTP_TCR_SNAPTYPSEL_1;
599 ptp_over_ipv4_udp = PTP_TCR_TSIPV4ENA;
600 ptp_over_ipv6_udp = PTP_TCR_TSIPV6ENA;
603 case HWTSTAMP_FILTER_PTP_V2_L4_SYNC:
604 /* PTP v2, UDP, Sync packet */
605 config.rx_filter = HWTSTAMP_FILTER_PTP_V2_L4_SYNC;
606 ptp_v2 = PTP_TCR_TSVER2ENA;
607 /* take time stamp for SYNC messages only */
608 ts_event_en = PTP_TCR_TSEVNTENA;
610 ptp_over_ipv4_udp = PTP_TCR_TSIPV4ENA;
611 ptp_over_ipv6_udp = PTP_TCR_TSIPV6ENA;
614 case HWTSTAMP_FILTER_PTP_V2_L4_DELAY_REQ:
615 /* PTP v2, UDP, Delay_req packet */
616 config.rx_filter = HWTSTAMP_FILTER_PTP_V2_L4_DELAY_REQ;
617 ptp_v2 = PTP_TCR_TSVER2ENA;
618 /* take time stamp for Delay_Req messages only */
619 ts_master_en = PTP_TCR_TSMSTRENA;
620 ts_event_en = PTP_TCR_TSEVNTENA;
622 ptp_over_ipv4_udp = PTP_TCR_TSIPV4ENA;
623 ptp_over_ipv6_udp = PTP_TCR_TSIPV6ENA;
626 case HWTSTAMP_FILTER_PTP_V2_EVENT:
627 /* PTP v2/802.AS1 any layer, any kind of event packet */
628 config.rx_filter = HWTSTAMP_FILTER_PTP_V2_EVENT;
629 ptp_v2 = PTP_TCR_TSVER2ENA;
630 /* take time stamp for all event messages */
631 if (priv->plat->has_gmac4)
632 snap_type_sel = PTP_GMAC4_TCR_SNAPTYPSEL_1;
634 snap_type_sel = PTP_TCR_SNAPTYPSEL_1;
636 ptp_over_ipv4_udp = PTP_TCR_TSIPV4ENA;
637 ptp_over_ipv6_udp = PTP_TCR_TSIPV6ENA;
638 ptp_over_ethernet = PTP_TCR_TSIPENA;
641 case HWTSTAMP_FILTER_PTP_V2_SYNC:
642 /* PTP v2/802.AS1, any layer, Sync packet */
643 config.rx_filter = HWTSTAMP_FILTER_PTP_V2_SYNC;
644 ptp_v2 = PTP_TCR_TSVER2ENA;
645 /* take time stamp for SYNC messages only */
646 ts_event_en = PTP_TCR_TSEVNTENA;
648 ptp_over_ipv4_udp = PTP_TCR_TSIPV4ENA;
649 ptp_over_ipv6_udp = PTP_TCR_TSIPV6ENA;
650 ptp_over_ethernet = PTP_TCR_TSIPENA;
653 case HWTSTAMP_FILTER_PTP_V2_DELAY_REQ:
654 /* PTP v2/802.AS1, any layer, Delay_req packet */
655 config.rx_filter = HWTSTAMP_FILTER_PTP_V2_DELAY_REQ;
656 ptp_v2 = PTP_TCR_TSVER2ENA;
657 /* take time stamp for Delay_Req messages only */
658 ts_master_en = PTP_TCR_TSMSTRENA;
659 ts_event_en = PTP_TCR_TSEVNTENA;
661 ptp_over_ipv4_udp = PTP_TCR_TSIPV4ENA;
662 ptp_over_ipv6_udp = PTP_TCR_TSIPV6ENA;
663 ptp_over_ethernet = PTP_TCR_TSIPENA;
666 case HWTSTAMP_FILTER_NTP_ALL:
667 case HWTSTAMP_FILTER_ALL:
668 /* time stamp any incoming packet */
669 config.rx_filter = HWTSTAMP_FILTER_ALL;
670 tstamp_all = PTP_TCR_TSENALL;
677 switch (config.rx_filter) {
678 case HWTSTAMP_FILTER_NONE:
679 config.rx_filter = HWTSTAMP_FILTER_NONE;
682 /* PTP v1, UDP, any kind of event packet */
683 config.rx_filter = HWTSTAMP_FILTER_PTP_V1_L4_EVENT;
687 priv->hwts_rx_en = ((config.rx_filter == HWTSTAMP_FILTER_NONE) ? 0 : 1);
688 priv->hwts_tx_en = config.tx_type == HWTSTAMP_TX_ON;
690 if (!priv->hwts_tx_en && !priv->hwts_rx_en)
691 priv->hw->ptp->config_hw_tstamping(priv->ptpaddr, 0);
693 value = (PTP_TCR_TSENA | PTP_TCR_TSCFUPDT | PTP_TCR_TSCTRLSSR |
694 tstamp_all | ptp_v2 | ptp_over_ethernet |
695 ptp_over_ipv6_udp | ptp_over_ipv4_udp | ts_event_en |
696 ts_master_en | snap_type_sel);
697 priv->hw->ptp->config_hw_tstamping(priv->ptpaddr, value);
699 /* program Sub Second Increment reg */
700 sec_inc = priv->hw->ptp->config_sub_second_increment(
701 priv->ptpaddr, priv->plat->clk_ptp_rate,
702 priv->plat->has_gmac4);
703 temp = div_u64(1000000000ULL, sec_inc);
705 /* calculate default added value:
707 * addend = (2^32)/freq_div_ratio;
708 * where, freq_div_ratio = 1e9ns/sec_inc
710 temp = (u64)(temp << 32);
711 priv->default_addend = div_u64(temp, priv->plat->clk_ptp_rate);
712 priv->hw->ptp->config_addend(priv->ptpaddr,
713 priv->default_addend);
715 /* initialize system time */
716 ktime_get_real_ts64(&now);
718 /* lower 32 bits of tv_sec are safe until y2106 */
719 priv->hw->ptp->init_systime(priv->ptpaddr, (u32)now.tv_sec,
723 return copy_to_user(ifr->ifr_data, &config,
724 sizeof(struct hwtstamp_config)) ? -EFAULT : 0;
728 * stmmac_init_ptp - init PTP
729 * @priv: driver private structure
730 * Description: this is to verify if the HW supports the PTPv1 or PTPv2.
731 * This is done by looking at the HW cap. register.
732 * This function also registers the ptp driver.
734 static int stmmac_init_ptp(struct stmmac_priv *priv)
736 if (!(priv->dma_cap.time_stamp || priv->dma_cap.atime_stamp))
740 /* Check if adv_ts can be enabled for dwmac 4.x core */
741 if (priv->plat->has_gmac4 && priv->dma_cap.atime_stamp)
743 /* Dwmac 3.x core with extend_desc can support adv_ts */
744 else if (priv->extend_desc && priv->dma_cap.atime_stamp)
747 if (priv->dma_cap.time_stamp)
748 netdev_info(priv->dev, "IEEE 1588-2002 Timestamp supported\n");
751 netdev_info(priv->dev,
752 "IEEE 1588-2008 Advanced Timestamp supported\n");
754 priv->hw->ptp = &stmmac_ptp;
755 priv->hwts_tx_en = 0;
756 priv->hwts_rx_en = 0;
758 stmmac_ptp_register(priv);
763 static void stmmac_release_ptp(struct stmmac_priv *priv)
765 if (priv->plat->clk_ptp_ref)
766 clk_disable_unprepare(priv->plat->clk_ptp_ref);
767 stmmac_ptp_unregister(priv);
771 * stmmac_mac_flow_ctrl - Configure flow control in all queues
772 * @priv: driver private structure
773 * Description: It is used for configuring the flow control in all queues
775 static void stmmac_mac_flow_ctrl(struct stmmac_priv *priv, u32 duplex)
777 u32 tx_cnt = priv->plat->tx_queues_to_use;
779 priv->hw->mac->flow_ctrl(priv->hw, duplex, priv->flow_ctrl,
780 priv->pause, tx_cnt);
784 * stmmac_adjust_link - adjusts the link parameters
785 * @dev: net device structure
786 * Description: this is the helper called by the physical abstraction layer
787 * drivers to communicate the phy link status. According the speed and duplex
788 * this driver can invoke registered glue-logic as well.
789 * It also invoke the eee initialization because it could happen when switch
790 * on different networks (that are eee capable).
792 static void stmmac_adjust_link(struct net_device *dev)
794 struct stmmac_priv *priv = netdev_priv(dev);
795 struct phy_device *phydev = dev->phydev;
797 bool new_state = false;
802 spin_lock_irqsave(&priv->lock, flags);
805 u32 ctrl = readl(priv->ioaddr + MAC_CTRL_REG);
807 /* Now we make sure that we can be in full duplex mode.
808 * If not, we operate in half-duplex mode. */
809 if (phydev->duplex != priv->oldduplex) {
812 ctrl &= ~priv->hw->link.duplex;
814 ctrl |= priv->hw->link.duplex;
815 priv->oldduplex = phydev->duplex;
817 /* Flow Control operation */
819 stmmac_mac_flow_ctrl(priv, phydev->duplex);
821 if (phydev->speed != priv->speed) {
823 ctrl &= ~priv->hw->link.speed_mask;
824 switch (phydev->speed) {
826 ctrl |= priv->hw->link.speed1000;
829 ctrl |= priv->hw->link.speed100;
832 ctrl |= priv->hw->link.speed10;
835 netif_warn(priv, link, priv->dev,
836 "broken speed: %d\n", phydev->speed);
837 phydev->speed = SPEED_UNKNOWN;
840 if (phydev->speed != SPEED_UNKNOWN)
841 stmmac_hw_fix_mac_speed(priv);
842 priv->speed = phydev->speed;
845 writel(ctrl, priv->ioaddr + MAC_CTRL_REG);
847 if (!priv->oldlink) {
849 priv->oldlink = true;
851 } else if (priv->oldlink) {
853 priv->oldlink = false;
854 priv->speed = SPEED_UNKNOWN;
855 priv->oldduplex = DUPLEX_UNKNOWN;
858 if (new_state && netif_msg_link(priv))
859 phy_print_status(phydev);
861 spin_unlock_irqrestore(&priv->lock, flags);
863 if (phydev->is_pseudo_fixed_link)
864 /* Stop PHY layer to call the hook to adjust the link in case
865 * of a switch is attached to the stmmac driver.
867 phydev->irq = PHY_IGNORE_INTERRUPT;
869 /* At this stage, init the EEE if supported.
870 * Never called in case of fixed_link.
872 priv->eee_enabled = stmmac_eee_init(priv);
876 * stmmac_check_pcs_mode - verify if RGMII/SGMII is supported
877 * @priv: driver private structure
878 * Description: this is to verify if the HW supports the PCS.
879 * Physical Coding Sublayer (PCS) interface that can be used when the MAC is
880 * configured for the TBI, RTBI, or SGMII PHY interface.
882 static void stmmac_check_pcs_mode(struct stmmac_priv *priv)
884 int interface = priv->plat->interface;
886 if (priv->dma_cap.pcs) {
887 if ((interface == PHY_INTERFACE_MODE_RGMII) ||
888 (interface == PHY_INTERFACE_MODE_RGMII_ID) ||
889 (interface == PHY_INTERFACE_MODE_RGMII_RXID) ||
890 (interface == PHY_INTERFACE_MODE_RGMII_TXID)) {
891 netdev_dbg(priv->dev, "PCS RGMII support enabled\n");
892 priv->hw->pcs = STMMAC_PCS_RGMII;
893 } else if (interface == PHY_INTERFACE_MODE_SGMII) {
894 netdev_dbg(priv->dev, "PCS SGMII support enabled\n");
895 priv->hw->pcs = STMMAC_PCS_SGMII;
901 * stmmac_init_phy - PHY initialization
902 * @dev: net device structure
903 * Description: it initializes the driver's PHY state, and attaches the PHY
908 static int stmmac_init_phy(struct net_device *dev)
910 struct stmmac_priv *priv = netdev_priv(dev);
911 struct phy_device *phydev;
912 char phy_id_fmt[MII_BUS_ID_SIZE + 3];
913 char bus_id[MII_BUS_ID_SIZE];
914 int interface = priv->plat->interface;
915 int max_speed = priv->plat->max_speed;
916 priv->oldlink = false;
917 priv->speed = SPEED_UNKNOWN;
918 priv->oldduplex = DUPLEX_UNKNOWN;
920 if (priv->plat->phy_node) {
921 phydev = of_phy_connect(dev, priv->plat->phy_node,
922 &stmmac_adjust_link, 0, interface);
924 snprintf(bus_id, MII_BUS_ID_SIZE, "stmmac-%x",
927 snprintf(phy_id_fmt, MII_BUS_ID_SIZE + 3, PHY_ID_FMT, bus_id,
928 priv->plat->phy_addr);
929 netdev_dbg(priv->dev, "%s: trying to attach to %s\n", __func__,
932 phydev = phy_connect(dev, phy_id_fmt, &stmmac_adjust_link,
936 if (IS_ERR_OR_NULL(phydev)) {
937 netdev_err(priv->dev, "Could not attach to PHY\n");
941 return PTR_ERR(phydev);
944 /* Stop Advertising 1000BASE Capability if interface is not GMII */
945 if ((interface == PHY_INTERFACE_MODE_MII) ||
946 (interface == PHY_INTERFACE_MODE_RMII) ||
947 (max_speed < 1000 && max_speed > 0))
948 phydev->advertising &= ~(SUPPORTED_1000baseT_Half |
949 SUPPORTED_1000baseT_Full);
952 * Broken HW is sometimes missing the pull-up resistor on the
953 * MDIO line, which results in reads to non-existent devices returning
954 * 0 rather than 0xffff. Catch this here and treat 0 as a non-existent
956 * Note: phydev->phy_id is the result of reading the UID PHY registers.
958 if (!priv->plat->phy_node && phydev->phy_id == 0) {
959 phy_disconnect(phydev);
963 /* stmmac_adjust_link will change this to PHY_IGNORE_INTERRUPT to avoid
964 * subsequent PHY polling, make sure we force a link transition if
965 * we have a UP/DOWN/UP transition
967 if (phydev->is_pseudo_fixed_link)
968 phydev->irq = PHY_POLL;
970 phy_attached_info(phydev);
974 static void stmmac_display_rx_rings(struct stmmac_priv *priv)
976 u32 rx_cnt = priv->plat->rx_queues_to_use;
980 /* Display RX rings */
981 for (queue = 0; queue < rx_cnt; queue++) {
982 struct stmmac_rx_queue *rx_q = &priv->rx_queue[queue];
984 pr_info("\tRX Queue %u rings\n", queue);
986 if (priv->extend_desc)
987 head_rx = (void *)rx_q->dma_erx;
989 head_rx = (void *)rx_q->dma_rx;
991 /* Display RX ring */
992 priv->hw->desc->display_ring(head_rx, DMA_RX_SIZE, true);
996 static void stmmac_display_tx_rings(struct stmmac_priv *priv)
998 u32 tx_cnt = priv->plat->tx_queues_to_use;
1002 /* Display TX rings */
1003 for (queue = 0; queue < tx_cnt; queue++) {
1004 struct stmmac_tx_queue *tx_q = &priv->tx_queue[queue];
1006 pr_info("\tTX Queue %d rings\n", queue);
1008 if (priv->extend_desc)
1009 head_tx = (void *)tx_q->dma_etx;
1011 head_tx = (void *)tx_q->dma_tx;
1013 priv->hw->desc->display_ring(head_tx, DMA_TX_SIZE, false);
1017 static void stmmac_display_rings(struct stmmac_priv *priv)
1019 /* Display RX ring */
1020 stmmac_display_rx_rings(priv);
1022 /* Display TX ring */
1023 stmmac_display_tx_rings(priv);
1026 static int stmmac_set_bfsize(int mtu, int bufsize)
1030 if (mtu >= BUF_SIZE_4KiB)
1031 ret = BUF_SIZE_8KiB;
1032 else if (mtu >= BUF_SIZE_2KiB)
1033 ret = BUF_SIZE_4KiB;
1034 else if (mtu > DEFAULT_BUFSIZE)
1035 ret = BUF_SIZE_2KiB;
1037 ret = DEFAULT_BUFSIZE;
1043 * stmmac_clear_rx_descriptors - clear RX descriptors
1044 * @priv: driver private structure
1045 * @queue: RX queue index
1046 * Description: this function is called to clear the RX descriptors
1047 * in case of both basic and extended descriptors are used.
1049 static void stmmac_clear_rx_descriptors(struct stmmac_priv *priv, u32 queue)
1051 struct stmmac_rx_queue *rx_q = &priv->rx_queue[queue];
1054 /* Clear the RX descriptors */
1055 for (i = 0; i < DMA_RX_SIZE; i++)
1056 if (priv->extend_desc)
1057 priv->hw->desc->init_rx_desc(&rx_q->dma_erx[i].basic,
1058 priv->use_riwt, priv->mode,
1059 (i == DMA_RX_SIZE - 1));
1061 priv->hw->desc->init_rx_desc(&rx_q->dma_rx[i],
1062 priv->use_riwt, priv->mode,
1063 (i == DMA_RX_SIZE - 1));
1067 * stmmac_clear_tx_descriptors - clear tx descriptors
1068 * @priv: driver private structure
1069 * @queue: TX queue index.
1070 * Description: this function is called to clear the TX descriptors
1071 * in case of both basic and extended descriptors are used.
1073 static void stmmac_clear_tx_descriptors(struct stmmac_priv *priv, u32 queue)
1075 struct stmmac_tx_queue *tx_q = &priv->tx_queue[queue];
1078 /* Clear the TX descriptors */
1079 for (i = 0; i < DMA_TX_SIZE; i++)
1080 if (priv->extend_desc)
1081 priv->hw->desc->init_tx_desc(&tx_q->dma_etx[i].basic,
1083 (i == DMA_TX_SIZE - 1));
1085 priv->hw->desc->init_tx_desc(&tx_q->dma_tx[i],
1087 (i == DMA_TX_SIZE - 1));
1091 * stmmac_clear_descriptors - clear descriptors
1092 * @priv: driver private structure
1093 * Description: this function is called to clear the TX and RX descriptors
1094 * in case of both basic and extended descriptors are used.
1096 static void stmmac_clear_descriptors(struct stmmac_priv *priv)
1098 u32 rx_queue_cnt = priv->plat->rx_queues_to_use;
1099 u32 tx_queue_cnt = priv->plat->tx_queues_to_use;
1102 /* Clear the RX descriptors */
1103 for (queue = 0; queue < rx_queue_cnt; queue++)
1104 stmmac_clear_rx_descriptors(priv, queue);
1106 /* Clear the TX descriptors */
1107 for (queue = 0; queue < tx_queue_cnt; queue++)
1108 stmmac_clear_tx_descriptors(priv, queue);
1112 * stmmac_init_rx_buffers - init the RX descriptor buffer.
1113 * @priv: driver private structure
1114 * @p: descriptor pointer
1115 * @i: descriptor index
1117 * @queue: RX queue index
1118 * Description: this function is called to allocate a receive buffer, perform
1119 * the DMA mapping and init the descriptor.
1121 static int stmmac_init_rx_buffers(struct stmmac_priv *priv, struct dma_desc *p,
1122 int i, gfp_t flags, u32 queue)
1124 struct stmmac_rx_queue *rx_q = &priv->rx_queue[queue];
1125 struct sk_buff *skb;
1127 skb = __netdev_alloc_skb_ip_align(priv->dev, priv->dma_buf_sz, flags);
1129 netdev_err(priv->dev,
1130 "%s: Rx init fails; skb is NULL\n", __func__);
1133 rx_q->rx_skbuff[i] = skb;
1134 rx_q->rx_skbuff_dma[i] = dma_map_single(priv->device, skb->data,
1137 if (dma_mapping_error(priv->device, rx_q->rx_skbuff_dma[i])) {
1138 netdev_err(priv->dev, "%s: DMA mapping error\n", __func__);
1139 dev_kfree_skb_any(skb);
1143 if (priv->synopsys_id >= DWMAC_CORE_4_00)
1144 p->des0 = cpu_to_le32(rx_q->rx_skbuff_dma[i]);
1146 p->des2 = cpu_to_le32(rx_q->rx_skbuff_dma[i]);
1148 if ((priv->hw->mode->init_desc3) &&
1149 (priv->dma_buf_sz == BUF_SIZE_16KiB))
1150 priv->hw->mode->init_desc3(p);
1156 * stmmac_free_rx_buffer - free RX dma buffers
1157 * @priv: private structure
1158 * @queue: RX queue index
1161 static void stmmac_free_rx_buffer(struct stmmac_priv *priv, u32 queue, int i)
1163 struct stmmac_rx_queue *rx_q = &priv->rx_queue[queue];
1165 if (rx_q->rx_skbuff[i]) {
1166 dma_unmap_single(priv->device, rx_q->rx_skbuff_dma[i],
1167 priv->dma_buf_sz, DMA_FROM_DEVICE);
1168 dev_kfree_skb_any(rx_q->rx_skbuff[i]);
1170 rx_q->rx_skbuff[i] = NULL;
1174 * stmmac_free_tx_buffer - free RX dma buffers
1175 * @priv: private structure
1176 * @queue: RX queue index
1179 static void stmmac_free_tx_buffer(struct stmmac_priv *priv, u32 queue, int i)
1181 struct stmmac_tx_queue *tx_q = &priv->tx_queue[queue];
1183 if (tx_q->tx_skbuff_dma[i].buf) {
1184 if (tx_q->tx_skbuff_dma[i].map_as_page)
1185 dma_unmap_page(priv->device,
1186 tx_q->tx_skbuff_dma[i].buf,
1187 tx_q->tx_skbuff_dma[i].len,
1190 dma_unmap_single(priv->device,
1191 tx_q->tx_skbuff_dma[i].buf,
1192 tx_q->tx_skbuff_dma[i].len,
1196 if (tx_q->tx_skbuff[i]) {
1197 dev_kfree_skb_any(tx_q->tx_skbuff[i]);
1198 tx_q->tx_skbuff[i] = NULL;
1199 tx_q->tx_skbuff_dma[i].buf = 0;
1200 tx_q->tx_skbuff_dma[i].map_as_page = false;
1205 * init_dma_rx_desc_rings - init the RX descriptor rings
1206 * @dev: net device structure
1208 * Description: this function initializes the DMA RX descriptors
1209 * and allocates the socket buffers. It supports the chained and ring
1212 static int init_dma_rx_desc_rings(struct net_device *dev, gfp_t flags)
1214 struct stmmac_priv *priv = netdev_priv(dev);
1215 u32 rx_count = priv->plat->rx_queues_to_use;
1216 unsigned int bfsize = 0;
1221 if (priv->hw->mode->set_16kib_bfsize)
1222 bfsize = priv->hw->mode->set_16kib_bfsize(dev->mtu);
1224 if (bfsize < BUF_SIZE_16KiB)
1225 bfsize = stmmac_set_bfsize(dev->mtu, priv->dma_buf_sz);
1227 priv->dma_buf_sz = bfsize;
1229 /* RX INITIALIZATION */
1230 netif_dbg(priv, probe, priv->dev,
1231 "SKB addresses:\nskb\t\tskb data\tdma data\n");
1233 for (queue = 0; queue < rx_count; queue++) {
1234 struct stmmac_rx_queue *rx_q = &priv->rx_queue[queue];
1236 netif_dbg(priv, probe, priv->dev,
1237 "(%s) dma_rx_phy=0x%08x\n", __func__,
1238 (u32)rx_q->dma_rx_phy);
1240 for (i = 0; i < DMA_RX_SIZE; i++) {
1243 if (priv->extend_desc)
1244 p = &((rx_q->dma_erx + i)->basic);
1246 p = rx_q->dma_rx + i;
1248 ret = stmmac_init_rx_buffers(priv, p, i, flags,
1251 goto err_init_rx_buffers;
1253 netif_dbg(priv, probe, priv->dev, "[%p]\t[%p]\t[%x]\n",
1254 rx_q->rx_skbuff[i], rx_q->rx_skbuff[i]->data,
1255 (unsigned int)rx_q->rx_skbuff_dma[i]);
1259 rx_q->dirty_rx = (unsigned int)(i - DMA_RX_SIZE);
1261 stmmac_clear_rx_descriptors(priv, queue);
1263 /* Setup the chained descriptor addresses */
1264 if (priv->mode == STMMAC_CHAIN_MODE) {
1265 if (priv->extend_desc)
1266 priv->hw->mode->init(rx_q->dma_erx,
1270 priv->hw->mode->init(rx_q->dma_rx,
1280 err_init_rx_buffers:
1281 while (queue >= 0) {
1283 stmmac_free_rx_buffer(priv, queue, i);
1296 * init_dma_tx_desc_rings - init the TX descriptor rings
1297 * @dev: net device structure.
1298 * Description: this function initializes the DMA TX descriptors
1299 * and allocates the socket buffers. It supports the chained and ring
1302 static int init_dma_tx_desc_rings(struct net_device *dev)
1304 struct stmmac_priv *priv = netdev_priv(dev);
1305 u32 tx_queue_cnt = priv->plat->tx_queues_to_use;
1309 for (queue = 0; queue < tx_queue_cnt; queue++) {
1310 struct stmmac_tx_queue *tx_q = &priv->tx_queue[queue];
1312 netif_dbg(priv, probe, priv->dev,
1313 "(%s) dma_tx_phy=0x%08x\n", __func__,
1314 (u32)tx_q->dma_tx_phy);
1316 /* Setup the chained descriptor addresses */
1317 if (priv->mode == STMMAC_CHAIN_MODE) {
1318 if (priv->extend_desc)
1319 priv->hw->mode->init(tx_q->dma_etx,
1323 priv->hw->mode->init(tx_q->dma_tx,
1328 for (i = 0; i < DMA_TX_SIZE; i++) {
1330 if (priv->extend_desc)
1331 p = &((tx_q->dma_etx + i)->basic);
1333 p = tx_q->dma_tx + i;
1335 if (priv->synopsys_id >= DWMAC_CORE_4_00) {
1344 tx_q->tx_skbuff_dma[i].buf = 0;
1345 tx_q->tx_skbuff_dma[i].map_as_page = false;
1346 tx_q->tx_skbuff_dma[i].len = 0;
1347 tx_q->tx_skbuff_dma[i].last_segment = false;
1348 tx_q->tx_skbuff[i] = NULL;
1354 netdev_tx_reset_queue(netdev_get_tx_queue(priv->dev, queue));
1361 * init_dma_desc_rings - init the RX/TX descriptor rings
1362 * @dev: net device structure
1364 * Description: this function initializes the DMA RX/TX descriptors
1365 * and allocates the socket buffers. It supports the chained and ring
1368 static int init_dma_desc_rings(struct net_device *dev, gfp_t flags)
1370 struct stmmac_priv *priv = netdev_priv(dev);
1373 ret = init_dma_rx_desc_rings(dev, flags);
1377 ret = init_dma_tx_desc_rings(dev);
1379 stmmac_clear_descriptors(priv);
1381 if (netif_msg_hw(priv))
1382 stmmac_display_rings(priv);
1388 * dma_free_rx_skbufs - free RX dma buffers
1389 * @priv: private structure
1390 * @queue: RX queue index
1392 static void dma_free_rx_skbufs(struct stmmac_priv *priv, u32 queue)
1396 for (i = 0; i < DMA_RX_SIZE; i++)
1397 stmmac_free_rx_buffer(priv, queue, i);
1401 * dma_free_tx_skbufs - free TX dma buffers
1402 * @priv: private structure
1403 * @queue: TX queue index
1405 static void dma_free_tx_skbufs(struct stmmac_priv *priv, u32 queue)
1409 for (i = 0; i < DMA_TX_SIZE; i++)
1410 stmmac_free_tx_buffer(priv, queue, i);
1414 * free_dma_rx_desc_resources - free RX dma desc resources
1415 * @priv: private structure
1417 static void free_dma_rx_desc_resources(struct stmmac_priv *priv)
1419 u32 rx_count = priv->plat->rx_queues_to_use;
1422 /* Free RX queue resources */
1423 for (queue = 0; queue < rx_count; queue++) {
1424 struct stmmac_rx_queue *rx_q = &priv->rx_queue[queue];
1426 /* Release the DMA RX socket buffers */
1427 dma_free_rx_skbufs(priv, queue);
1429 /* Free DMA regions of consistent memory previously allocated */
1430 if (!priv->extend_desc)
1431 dma_free_coherent(priv->device,
1432 DMA_RX_SIZE * sizeof(struct dma_desc),
1433 rx_q->dma_rx, rx_q->dma_rx_phy);
1435 dma_free_coherent(priv->device, DMA_RX_SIZE *
1436 sizeof(struct dma_extended_desc),
1437 rx_q->dma_erx, rx_q->dma_rx_phy);
1439 kfree(rx_q->rx_skbuff_dma);
1440 kfree(rx_q->rx_skbuff);
1445 * free_dma_tx_desc_resources - free TX dma desc resources
1446 * @priv: private structure
1448 static void free_dma_tx_desc_resources(struct stmmac_priv *priv)
1450 u32 tx_count = priv->plat->tx_queues_to_use;
1453 /* Free TX queue resources */
1454 for (queue = 0; queue < tx_count; queue++) {
1455 struct stmmac_tx_queue *tx_q = &priv->tx_queue[queue];
1457 /* Release the DMA TX socket buffers */
1458 dma_free_tx_skbufs(priv, queue);
1460 /* Free DMA regions of consistent memory previously allocated */
1461 if (!priv->extend_desc)
1462 dma_free_coherent(priv->device,
1463 DMA_TX_SIZE * sizeof(struct dma_desc),
1464 tx_q->dma_tx, tx_q->dma_tx_phy);
1466 dma_free_coherent(priv->device, DMA_TX_SIZE *
1467 sizeof(struct dma_extended_desc),
1468 tx_q->dma_etx, tx_q->dma_tx_phy);
1470 kfree(tx_q->tx_skbuff_dma);
1471 kfree(tx_q->tx_skbuff);
1476 * alloc_dma_rx_desc_resources - alloc RX resources.
1477 * @priv: private structure
1478 * Description: according to which descriptor can be used (extend or basic)
1479 * this function allocates the resources for TX and RX paths. In case of
1480 * reception, for example, it pre-allocated the RX socket buffer in order to
1481 * allow zero-copy mechanism.
1483 static int alloc_dma_rx_desc_resources(struct stmmac_priv *priv)
1485 u32 rx_count = priv->plat->rx_queues_to_use;
1489 /* RX queues buffers and DMA */
1490 for (queue = 0; queue < rx_count; queue++) {
1491 struct stmmac_rx_queue *rx_q = &priv->rx_queue[queue];
1493 rx_q->queue_index = queue;
1494 rx_q->priv_data = priv;
1496 rx_q->rx_skbuff_dma = kmalloc_array(DMA_RX_SIZE,
1499 if (!rx_q->rx_skbuff_dma)
1502 rx_q->rx_skbuff = kmalloc_array(DMA_RX_SIZE,
1503 sizeof(struct sk_buff *),
1505 if (!rx_q->rx_skbuff)
1508 if (priv->extend_desc) {
1509 rx_q->dma_erx = dma_zalloc_coherent(priv->device,
1519 rx_q->dma_rx = dma_zalloc_coherent(priv->device,
1533 free_dma_rx_desc_resources(priv);
1539 * alloc_dma_tx_desc_resources - alloc TX resources.
1540 * @priv: private structure
1541 * Description: according to which descriptor can be used (extend or basic)
1542 * this function allocates the resources for TX and RX paths. In case of
1543 * reception, for example, it pre-allocated the RX socket buffer in order to
1544 * allow zero-copy mechanism.
1546 static int alloc_dma_tx_desc_resources(struct stmmac_priv *priv)
1548 u32 tx_count = priv->plat->tx_queues_to_use;
1552 /* TX queues buffers and DMA */
1553 for (queue = 0; queue < tx_count; queue++) {
1554 struct stmmac_tx_queue *tx_q = &priv->tx_queue[queue];
1556 tx_q->queue_index = queue;
1557 tx_q->priv_data = priv;
1559 tx_q->tx_skbuff_dma = kmalloc_array(DMA_TX_SIZE,
1560 sizeof(*tx_q->tx_skbuff_dma),
1562 if (!tx_q->tx_skbuff_dma)
1565 tx_q->tx_skbuff = kmalloc_array(DMA_TX_SIZE,
1566 sizeof(struct sk_buff *),
1568 if (!tx_q->tx_skbuff)
1571 if (priv->extend_desc) {
1572 tx_q->dma_etx = dma_zalloc_coherent(priv->device,
1581 tx_q->dma_tx = dma_zalloc_coherent(priv->device,
1595 free_dma_tx_desc_resources(priv);
1601 * alloc_dma_desc_resources - alloc TX/RX resources.
1602 * @priv: private structure
1603 * Description: according to which descriptor can be used (extend or basic)
1604 * this function allocates the resources for TX and RX paths. In case of
1605 * reception, for example, it pre-allocated the RX socket buffer in order to
1606 * allow zero-copy mechanism.
1608 static int alloc_dma_desc_resources(struct stmmac_priv *priv)
1611 int ret = alloc_dma_rx_desc_resources(priv);
1616 ret = alloc_dma_tx_desc_resources(priv);
1622 * free_dma_desc_resources - free dma desc resources
1623 * @priv: private structure
1625 static void free_dma_desc_resources(struct stmmac_priv *priv)
1627 /* Release the DMA RX socket buffers */
1628 free_dma_rx_desc_resources(priv);
1630 /* Release the DMA TX socket buffers */
1631 free_dma_tx_desc_resources(priv);
1635 * stmmac_mac_enable_rx_queues - Enable MAC rx queues
1636 * @priv: driver private structure
1637 * Description: It is used for enabling the rx queues in the MAC
1639 static void stmmac_mac_enable_rx_queues(struct stmmac_priv *priv)
1641 u32 rx_queues_count = priv->plat->rx_queues_to_use;
1645 for (queue = 0; queue < rx_queues_count; queue++) {
1646 mode = priv->plat->rx_queues_cfg[queue].mode_to_use;
1647 priv->hw->mac->rx_queue_enable(priv->hw, mode, queue);
1652 * stmmac_start_rx_dma - start RX DMA channel
1653 * @priv: driver private structure
1654 * @chan: RX channel index
1656 * This starts a RX DMA channel
1658 static void stmmac_start_rx_dma(struct stmmac_priv *priv, u32 chan)
1660 netdev_dbg(priv->dev, "DMA RX processes started in channel %d\n", chan);
1661 priv->hw->dma->start_rx(priv->ioaddr, chan);
1665 * stmmac_start_tx_dma - start TX DMA channel
1666 * @priv: driver private structure
1667 * @chan: TX channel index
1669 * This starts a TX DMA channel
1671 static void stmmac_start_tx_dma(struct stmmac_priv *priv, u32 chan)
1673 netdev_dbg(priv->dev, "DMA TX processes started in channel %d\n", chan);
1674 priv->hw->dma->start_tx(priv->ioaddr, chan);
1678 * stmmac_stop_rx_dma - stop RX DMA channel
1679 * @priv: driver private structure
1680 * @chan: RX channel index
1682 * This stops a RX DMA channel
1684 static void stmmac_stop_rx_dma(struct stmmac_priv *priv, u32 chan)
1686 netdev_dbg(priv->dev, "DMA RX processes stopped in channel %d\n", chan);
1687 priv->hw->dma->stop_rx(priv->ioaddr, chan);
1691 * stmmac_stop_tx_dma - stop TX DMA channel
1692 * @priv: driver private structure
1693 * @chan: TX channel index
1695 * This stops a TX DMA channel
1697 static void stmmac_stop_tx_dma(struct stmmac_priv *priv, u32 chan)
1699 netdev_dbg(priv->dev, "DMA TX processes stopped in channel %d\n", chan);
1700 priv->hw->dma->stop_tx(priv->ioaddr, chan);
1704 * stmmac_start_all_dma - start all RX and TX DMA channels
1705 * @priv: driver private structure
1707 * This starts all the RX and TX DMA channels
1709 static void stmmac_start_all_dma(struct stmmac_priv *priv)
1711 u32 rx_channels_count = priv->plat->rx_queues_to_use;
1712 u32 tx_channels_count = priv->plat->tx_queues_to_use;
1715 for (chan = 0; chan < rx_channels_count; chan++)
1716 stmmac_start_rx_dma(priv, chan);
1718 for (chan = 0; chan < tx_channels_count; chan++)
1719 stmmac_start_tx_dma(priv, chan);
1723 * stmmac_stop_all_dma - stop all RX and TX DMA channels
1724 * @priv: driver private structure
1726 * This stops the RX and TX DMA channels
1728 static void stmmac_stop_all_dma(struct stmmac_priv *priv)
1730 u32 rx_channels_count = priv->plat->rx_queues_to_use;
1731 u32 tx_channels_count = priv->plat->tx_queues_to_use;
1734 for (chan = 0; chan < rx_channels_count; chan++)
1735 stmmac_stop_rx_dma(priv, chan);
1737 for (chan = 0; chan < tx_channels_count; chan++)
1738 stmmac_stop_tx_dma(priv, chan);
1742 * stmmac_dma_operation_mode - HW DMA operation mode
1743 * @priv: driver private structure
1744 * Description: it is used for configuring the DMA operation mode register in
1745 * order to program the tx/rx DMA thresholds or Store-And-Forward mode.
1747 static void stmmac_dma_operation_mode(struct stmmac_priv *priv)
1749 u32 rx_channels_count = priv->plat->rx_queues_to_use;
1750 u32 tx_channels_count = priv->plat->tx_queues_to_use;
1751 int rxfifosz = priv->plat->rx_fifo_size;
1752 int txfifosz = priv->plat->tx_fifo_size;
1759 rxfifosz = priv->dma_cap.rx_fifo_size;
1761 txfifosz = priv->dma_cap.tx_fifo_size;
1763 /* Adjust for real per queue fifo size */
1764 rxfifosz /= rx_channels_count;
1765 txfifosz /= tx_channels_count;
1767 if (priv->plat->force_thresh_dma_mode) {
1770 } else if (priv->plat->force_sf_dma_mode || priv->plat->tx_coe) {
1772 * In case of GMAC, SF mode can be enabled
1773 * to perform the TX COE in HW. This depends on:
1774 * 1) TX COE if actually supported
1775 * 2) There is no bugged Jumbo frame support
1776 * that needs to not insert csum in the TDES.
1778 txmode = SF_DMA_MODE;
1779 rxmode = SF_DMA_MODE;
1780 priv->xstats.threshold = SF_DMA_MODE;
1783 rxmode = SF_DMA_MODE;
1786 /* configure all channels */
1787 if (priv->synopsys_id >= DWMAC_CORE_4_00) {
1788 for (chan = 0; chan < rx_channels_count; chan++) {
1789 qmode = priv->plat->rx_queues_cfg[chan].mode_to_use;
1791 priv->hw->dma->dma_rx_mode(priv->ioaddr, rxmode, chan,
1795 for (chan = 0; chan < tx_channels_count; chan++) {
1796 qmode = priv->plat->tx_queues_cfg[chan].mode_to_use;
1798 priv->hw->dma->dma_tx_mode(priv->ioaddr, txmode, chan,
1802 priv->hw->dma->dma_mode(priv->ioaddr, txmode, rxmode,
1808 * stmmac_tx_clean - to manage the transmission completion
1809 * @priv: driver private structure
1810 * @queue: TX queue index
1811 * Description: it reclaims the transmit resources after transmission completes.
1813 static void stmmac_tx_clean(struct stmmac_priv *priv, u32 queue)
1815 struct stmmac_tx_queue *tx_q = &priv->tx_queue[queue];
1816 unsigned int bytes_compl = 0, pkts_compl = 0;
1819 netif_tx_lock(priv->dev);
1821 priv->xstats.tx_clean++;
1823 entry = tx_q->dirty_tx;
1824 while (entry != tx_q->cur_tx) {
1825 struct sk_buff *skb = tx_q->tx_skbuff[entry];
1829 if (priv->extend_desc)
1830 p = (struct dma_desc *)(tx_q->dma_etx + entry);
1832 p = tx_q->dma_tx + entry;
1834 status = priv->hw->desc->tx_status(&priv->dev->stats,
1837 /* Check if the descriptor is owned by the DMA */
1838 if (unlikely(status & tx_dma_own))
1841 /* Just consider the last segment and ...*/
1842 if (likely(!(status & tx_not_ls))) {
1843 /* ... verify the status error condition */
1844 if (unlikely(status & tx_err)) {
1845 priv->dev->stats.tx_errors++;
1847 priv->dev->stats.tx_packets++;
1848 priv->xstats.tx_pkt_n++;
1850 stmmac_get_tx_hwtstamp(priv, p, skb);
1853 if (likely(tx_q->tx_skbuff_dma[entry].buf)) {
1854 if (tx_q->tx_skbuff_dma[entry].map_as_page)
1855 dma_unmap_page(priv->device,
1856 tx_q->tx_skbuff_dma[entry].buf,
1857 tx_q->tx_skbuff_dma[entry].len,
1860 dma_unmap_single(priv->device,
1861 tx_q->tx_skbuff_dma[entry].buf,
1862 tx_q->tx_skbuff_dma[entry].len,
1864 tx_q->tx_skbuff_dma[entry].buf = 0;
1865 tx_q->tx_skbuff_dma[entry].len = 0;
1866 tx_q->tx_skbuff_dma[entry].map_as_page = false;
1869 if (priv->hw->mode->clean_desc3)
1870 priv->hw->mode->clean_desc3(tx_q, p);
1872 tx_q->tx_skbuff_dma[entry].last_segment = false;
1873 tx_q->tx_skbuff_dma[entry].is_jumbo = false;
1875 if (likely(skb != NULL)) {
1877 bytes_compl += skb->len;
1878 dev_consume_skb_any(skb);
1879 tx_q->tx_skbuff[entry] = NULL;
1882 priv->hw->desc->release_tx_desc(p, priv->mode);
1884 entry = STMMAC_GET_ENTRY(entry, DMA_TX_SIZE);
1886 tx_q->dirty_tx = entry;
1888 netdev_tx_completed_queue(netdev_get_tx_queue(priv->dev, queue),
1889 pkts_compl, bytes_compl);
1891 if (unlikely(netif_tx_queue_stopped(netdev_get_tx_queue(priv->dev,
1893 stmmac_tx_avail(priv, queue) > STMMAC_TX_THRESH) {
1895 netif_dbg(priv, tx_done, priv->dev,
1896 "%s: restart transmit\n", __func__);
1897 netif_tx_wake_queue(netdev_get_tx_queue(priv->dev, queue));
1900 if ((priv->eee_enabled) && (!priv->tx_path_in_lpi_mode)) {
1901 stmmac_enable_eee_mode(priv);
1902 mod_timer(&priv->eee_ctrl_timer, STMMAC_LPI_T(eee_timer));
1904 netif_tx_unlock(priv->dev);
1907 static inline void stmmac_enable_dma_irq(struct stmmac_priv *priv, u32 chan)
1909 priv->hw->dma->enable_dma_irq(priv->ioaddr, chan);
1912 static inline void stmmac_disable_dma_irq(struct stmmac_priv *priv, u32 chan)
1914 priv->hw->dma->disable_dma_irq(priv->ioaddr, chan);
1918 * stmmac_tx_err - to manage the tx error
1919 * @priv: driver private structure
1920 * @chan: channel index
1921 * Description: it cleans the descriptors and restarts the transmission
1922 * in case of transmission errors.
1924 static void stmmac_tx_err(struct stmmac_priv *priv, u32 chan)
1926 struct stmmac_tx_queue *tx_q = &priv->tx_queue[chan];
1929 netif_tx_stop_queue(netdev_get_tx_queue(priv->dev, chan));
1931 stmmac_stop_tx_dma(priv, chan);
1932 dma_free_tx_skbufs(priv, chan);
1933 for (i = 0; i < DMA_TX_SIZE; i++)
1934 if (priv->extend_desc)
1935 priv->hw->desc->init_tx_desc(&tx_q->dma_etx[i].basic,
1937 (i == DMA_TX_SIZE - 1));
1939 priv->hw->desc->init_tx_desc(&tx_q->dma_tx[i],
1941 (i == DMA_TX_SIZE - 1));
1944 netdev_tx_reset_queue(netdev_get_tx_queue(priv->dev, chan));
1945 stmmac_start_tx_dma(priv, chan);
1947 priv->dev->stats.tx_errors++;
1948 netif_tx_wake_queue(netdev_get_tx_queue(priv->dev, chan));
1952 * stmmac_set_dma_operation_mode - Set DMA operation mode by channel
1953 * @priv: driver private structure
1954 * @txmode: TX operating mode
1955 * @rxmode: RX operating mode
1956 * @chan: channel index
1957 * Description: it is used for configuring of the DMA operation mode in
1958 * runtime in order to program the tx/rx DMA thresholds or Store-And-Forward
1961 static void stmmac_set_dma_operation_mode(struct stmmac_priv *priv, u32 txmode,
1962 u32 rxmode, u32 chan)
1964 u8 rxqmode = priv->plat->rx_queues_cfg[chan].mode_to_use;
1965 u8 txqmode = priv->plat->tx_queues_cfg[chan].mode_to_use;
1966 u32 rx_channels_count = priv->plat->rx_queues_to_use;
1967 u32 tx_channels_count = priv->plat->tx_queues_to_use;
1968 int rxfifosz = priv->plat->rx_fifo_size;
1969 int txfifosz = priv->plat->tx_fifo_size;
1972 rxfifosz = priv->dma_cap.rx_fifo_size;
1974 txfifosz = priv->dma_cap.tx_fifo_size;
1976 /* Adjust for real per queue fifo size */
1977 rxfifosz /= rx_channels_count;
1978 txfifosz /= tx_channels_count;
1980 if (priv->synopsys_id >= DWMAC_CORE_4_00) {
1981 priv->hw->dma->dma_rx_mode(priv->ioaddr, rxmode, chan,
1983 priv->hw->dma->dma_tx_mode(priv->ioaddr, txmode, chan,
1986 priv->hw->dma->dma_mode(priv->ioaddr, txmode, rxmode,
1992 * stmmac_dma_interrupt - DMA ISR
1993 * @priv: driver private structure
1994 * Description: this is the DMA ISR. It is called by the main ISR.
1995 * It calls the dwmac dma routine and schedule poll method in case of some
1998 static void stmmac_dma_interrupt(struct stmmac_priv *priv)
2000 u32 tx_channel_count = priv->plat->tx_queues_to_use;
2004 for (chan = 0; chan < tx_channel_count; chan++) {
2005 struct stmmac_rx_queue *rx_q = &priv->rx_queue[chan];
2007 status = priv->hw->dma->dma_interrupt(priv->ioaddr,
2008 &priv->xstats, chan);
2009 if (likely((status & handle_rx)) || (status & handle_tx)) {
2010 if (likely(napi_schedule_prep(&rx_q->napi))) {
2011 stmmac_disable_dma_irq(priv, chan);
2012 __napi_schedule(&rx_q->napi);
2016 if (unlikely(status & tx_hard_error_bump_tc)) {
2017 /* Try to bump up the dma threshold on this failure */
2018 if (unlikely(priv->xstats.threshold != SF_DMA_MODE) &&
2021 if (priv->plat->force_thresh_dma_mode)
2022 stmmac_set_dma_operation_mode(priv,
2027 stmmac_set_dma_operation_mode(priv,
2031 priv->xstats.threshold = tc;
2033 } else if (unlikely(status == tx_hard_error)) {
2034 stmmac_tx_err(priv, chan);
2040 * stmmac_mmc_setup: setup the Mac Management Counters (MMC)
2041 * @priv: driver private structure
2042 * Description: this masks the MMC irq, in fact, the counters are managed in SW.
2044 static void stmmac_mmc_setup(struct stmmac_priv *priv)
2046 unsigned int mode = MMC_CNTRL_RESET_ON_READ | MMC_CNTRL_COUNTER_RESET |
2047 MMC_CNTRL_PRESET | MMC_CNTRL_FULL_HALF_PRESET;
2049 if (priv->synopsys_id >= DWMAC_CORE_4_00) {
2050 priv->ptpaddr = priv->ioaddr + PTP_GMAC4_OFFSET;
2051 priv->mmcaddr = priv->ioaddr + MMC_GMAC4_OFFSET;
2053 priv->ptpaddr = priv->ioaddr + PTP_GMAC3_X_OFFSET;
2054 priv->mmcaddr = priv->ioaddr + MMC_GMAC3_X_OFFSET;
2057 dwmac_mmc_intr_all_mask(priv->mmcaddr);
2059 if (priv->dma_cap.rmon) {
2060 dwmac_mmc_ctrl(priv->mmcaddr, mode);
2061 memset(&priv->mmc, 0, sizeof(struct stmmac_counters));
2063 netdev_info(priv->dev, "No MAC Management Counters available\n");
2067 * stmmac_selec_desc_mode - to select among: normal/alternate/extend descriptors
2068 * @priv: driver private structure
2069 * Description: select the Enhanced/Alternate or Normal descriptors.
2070 * In case of Enhanced/Alternate, it checks if the extended descriptors are
2071 * supported by the HW capability register.
2073 static void stmmac_selec_desc_mode(struct stmmac_priv *priv)
2075 if (priv->plat->enh_desc) {
2076 dev_info(priv->device, "Enhanced/Alternate descriptors\n");
2078 /* GMAC older than 3.50 has no extended descriptors */
2079 if (priv->synopsys_id >= DWMAC_CORE_3_50) {
2080 dev_info(priv->device, "Enabled extended descriptors\n");
2081 priv->extend_desc = 1;
2083 dev_warn(priv->device, "Extended descriptors not supported\n");
2085 priv->hw->desc = &enh_desc_ops;
2087 dev_info(priv->device, "Normal descriptors\n");
2088 priv->hw->desc = &ndesc_ops;
2093 * stmmac_get_hw_features - get MAC capabilities from the HW cap. register.
2094 * @priv: driver private structure
2096 * new GMAC chip generations have a new register to indicate the
2097 * presence of the optional feature/functions.
2098 * This can be also used to override the value passed through the
2099 * platform and necessary for old MAC10/100 and GMAC chips.
2101 static int stmmac_get_hw_features(struct stmmac_priv *priv)
2105 if (priv->hw->dma->get_hw_feature) {
2106 priv->hw->dma->get_hw_feature(priv->ioaddr,
2115 * stmmac_check_ether_addr - check if the MAC addr is valid
2116 * @priv: driver private structure
2118 * it is to verify if the MAC address is valid, in case of failures it
2119 * generates a random MAC address
2121 static void stmmac_check_ether_addr(struct stmmac_priv *priv)
2123 if (!is_valid_ether_addr(priv->dev->dev_addr)) {
2124 priv->hw->mac->get_umac_addr(priv->hw,
2125 priv->dev->dev_addr, 0);
2126 if (!is_valid_ether_addr(priv->dev->dev_addr))
2127 eth_hw_addr_random(priv->dev);
2128 netdev_info(priv->dev, "device MAC address %pM\n",
2129 priv->dev->dev_addr);
2134 * stmmac_init_dma_engine - DMA init.
2135 * @priv: driver private structure
2137 * It inits the DMA invoking the specific MAC/GMAC callback.
2138 * Some DMA parameters can be passed from the platform;
2139 * in case of these are not passed a default is kept for the MAC or GMAC.
2141 static int stmmac_init_dma_engine(struct stmmac_priv *priv)
2143 u32 rx_channels_count = priv->plat->rx_queues_to_use;
2144 u32 tx_channels_count = priv->plat->tx_queues_to_use;
2145 struct stmmac_rx_queue *rx_q;
2146 struct stmmac_tx_queue *tx_q;
2147 u32 dummy_dma_rx_phy = 0;
2148 u32 dummy_dma_tx_phy = 0;
2153 if (!priv->plat->dma_cfg || !priv->plat->dma_cfg->pbl) {
2154 dev_err(priv->device, "Invalid DMA configuration\n");
2158 if (priv->extend_desc && (priv->mode == STMMAC_RING_MODE))
2161 ret = priv->hw->dma->reset(priv->ioaddr);
2163 dev_err(priv->device, "Failed to reset the dma\n");
2167 if (priv->synopsys_id >= DWMAC_CORE_4_00) {
2168 /* DMA Configuration */
2169 priv->hw->dma->init(priv->ioaddr, priv->plat->dma_cfg,
2170 dummy_dma_tx_phy, dummy_dma_rx_phy, atds);
2172 /* DMA RX Channel Configuration */
2173 for (chan = 0; chan < rx_channels_count; chan++) {
2174 rx_q = &priv->rx_queue[chan];
2176 priv->hw->dma->init_rx_chan(priv->ioaddr,
2177 priv->plat->dma_cfg,
2178 rx_q->dma_rx_phy, chan);
2180 rx_q->rx_tail_addr = rx_q->dma_rx_phy +
2181 (DMA_RX_SIZE * sizeof(struct dma_desc));
2182 priv->hw->dma->set_rx_tail_ptr(priv->ioaddr,
2187 /* DMA TX Channel Configuration */
2188 for (chan = 0; chan < tx_channels_count; chan++) {
2189 tx_q = &priv->tx_queue[chan];
2191 priv->hw->dma->init_chan(priv->ioaddr,
2192 priv->plat->dma_cfg,
2195 priv->hw->dma->init_tx_chan(priv->ioaddr,
2196 priv->plat->dma_cfg,
2197 tx_q->dma_tx_phy, chan);
2199 tx_q->tx_tail_addr = tx_q->dma_tx_phy +
2200 (DMA_TX_SIZE * sizeof(struct dma_desc));
2201 priv->hw->dma->set_tx_tail_ptr(priv->ioaddr,
2206 rx_q = &priv->rx_queue[chan];
2207 tx_q = &priv->tx_queue[chan];
2208 priv->hw->dma->init(priv->ioaddr, priv->plat->dma_cfg,
2209 tx_q->dma_tx_phy, rx_q->dma_rx_phy, atds);
2212 if (priv->plat->axi && priv->hw->dma->axi)
2213 priv->hw->dma->axi(priv->ioaddr, priv->plat->axi);
2219 * stmmac_tx_timer - mitigation sw timer for tx.
2220 * @data: data pointer
2222 * This is the timer handler to directly invoke the stmmac_tx_clean.
2224 static void stmmac_tx_timer(unsigned long data)
2226 struct stmmac_priv *priv = (struct stmmac_priv *)data;
2227 u32 tx_queues_count = priv->plat->tx_queues_to_use;
2230 /* let's scan all the tx queues */
2231 for (queue = 0; queue < tx_queues_count; queue++)
2232 stmmac_tx_clean(priv, queue);
2236 * stmmac_init_tx_coalesce - init tx mitigation options.
2237 * @priv: driver private structure
2239 * This inits the transmit coalesce parameters: i.e. timer rate,
2240 * timer handler and default threshold used for enabling the
2241 * interrupt on completion bit.
2243 static void stmmac_init_tx_coalesce(struct stmmac_priv *priv)
2245 priv->tx_coal_frames = STMMAC_TX_FRAMES;
2246 priv->tx_coal_timer = STMMAC_COAL_TX_TIMER;
2247 setup_timer(&priv->txtimer, stmmac_tx_timer, (unsigned long)priv);
2248 priv->txtimer.expires = STMMAC_COAL_TIMER(priv->tx_coal_timer);
2249 add_timer(&priv->txtimer);
2252 static void stmmac_set_rings_length(struct stmmac_priv *priv)
2254 u32 rx_channels_count = priv->plat->rx_queues_to_use;
2255 u32 tx_channels_count = priv->plat->tx_queues_to_use;
2258 /* set TX ring length */
2259 if (priv->hw->dma->set_tx_ring_len) {
2260 for (chan = 0; chan < tx_channels_count; chan++)
2261 priv->hw->dma->set_tx_ring_len(priv->ioaddr,
2262 (DMA_TX_SIZE - 1), chan);
2265 /* set RX ring length */
2266 if (priv->hw->dma->set_rx_ring_len) {
2267 for (chan = 0; chan < rx_channels_count; chan++)
2268 priv->hw->dma->set_rx_ring_len(priv->ioaddr,
2269 (DMA_RX_SIZE - 1), chan);
2274 * stmmac_set_tx_queue_weight - Set TX queue weight
2275 * @priv: driver private structure
2276 * Description: It is used for setting TX queues weight
2278 static void stmmac_set_tx_queue_weight(struct stmmac_priv *priv)
2280 u32 tx_queues_count = priv->plat->tx_queues_to_use;
2284 for (queue = 0; queue < tx_queues_count; queue++) {
2285 weight = priv->plat->tx_queues_cfg[queue].weight;
2286 priv->hw->mac->set_mtl_tx_queue_weight(priv->hw, weight, queue);
2291 * stmmac_configure_cbs - Configure CBS in TX queue
2292 * @priv: driver private structure
2293 * Description: It is used for configuring CBS in AVB TX queues
2295 static void stmmac_configure_cbs(struct stmmac_priv *priv)
2297 u32 tx_queues_count = priv->plat->tx_queues_to_use;
2301 /* queue 0 is reserved for legacy traffic */
2302 for (queue = 1; queue < tx_queues_count; queue++) {
2303 mode_to_use = priv->plat->tx_queues_cfg[queue].mode_to_use;
2304 if (mode_to_use == MTL_QUEUE_DCB)
2307 priv->hw->mac->config_cbs(priv->hw,
2308 priv->plat->tx_queues_cfg[queue].send_slope,
2309 priv->plat->tx_queues_cfg[queue].idle_slope,
2310 priv->plat->tx_queues_cfg[queue].high_credit,
2311 priv->plat->tx_queues_cfg[queue].low_credit,
2317 * stmmac_rx_queue_dma_chan_map - Map RX queue to RX dma channel
2318 * @priv: driver private structure
2319 * Description: It is used for mapping RX queues to RX dma channels
2321 static void stmmac_rx_queue_dma_chan_map(struct stmmac_priv *priv)
2323 u32 rx_queues_count = priv->plat->rx_queues_to_use;
2327 for (queue = 0; queue < rx_queues_count; queue++) {
2328 chan = priv->plat->rx_queues_cfg[queue].chan;
2329 priv->hw->mac->map_mtl_to_dma(priv->hw, queue, chan);
2334 * stmmac_mac_config_rx_queues_prio - Configure RX Queue priority
2335 * @priv: driver private structure
2336 * Description: It is used for configuring the RX Queue Priority
2338 static void stmmac_mac_config_rx_queues_prio(struct stmmac_priv *priv)
2340 u32 rx_queues_count = priv->plat->rx_queues_to_use;
2344 for (queue = 0; queue < rx_queues_count; queue++) {
2345 if (!priv->plat->rx_queues_cfg[queue].use_prio)
2348 prio = priv->plat->rx_queues_cfg[queue].prio;
2349 priv->hw->mac->rx_queue_prio(priv->hw, prio, queue);
2354 * stmmac_mac_config_tx_queues_prio - Configure TX Queue priority
2355 * @priv: driver private structure
2356 * Description: It is used for configuring the TX Queue Priority
2358 static void stmmac_mac_config_tx_queues_prio(struct stmmac_priv *priv)
2360 u32 tx_queues_count = priv->plat->tx_queues_to_use;
2364 for (queue = 0; queue < tx_queues_count; queue++) {
2365 if (!priv->plat->tx_queues_cfg[queue].use_prio)
2368 prio = priv->plat->tx_queues_cfg[queue].prio;
2369 priv->hw->mac->tx_queue_prio(priv->hw, prio, queue);
2374 * stmmac_mac_config_rx_queues_routing - Configure RX Queue Routing
2375 * @priv: driver private structure
2376 * Description: It is used for configuring the RX queue routing
2378 static void stmmac_mac_config_rx_queues_routing(struct stmmac_priv *priv)
2380 u32 rx_queues_count = priv->plat->rx_queues_to_use;
2384 for (queue = 0; queue < rx_queues_count; queue++) {
2385 /* no specific packet type routing specified for the queue */
2386 if (priv->plat->rx_queues_cfg[queue].pkt_route == 0x0)
2389 packet = priv->plat->rx_queues_cfg[queue].pkt_route;
2390 priv->hw->mac->rx_queue_prio(priv->hw, packet, queue);
2395 * stmmac_mtl_configuration - Configure MTL
2396 * @priv: driver private structure
2397 * Description: It is used for configurring MTL
2399 static void stmmac_mtl_configuration(struct stmmac_priv *priv)
2401 u32 rx_queues_count = priv->plat->rx_queues_to_use;
2402 u32 tx_queues_count = priv->plat->tx_queues_to_use;
2404 if (tx_queues_count > 1 && priv->hw->mac->set_mtl_tx_queue_weight)
2405 stmmac_set_tx_queue_weight(priv);
2407 /* Configure MTL RX algorithms */
2408 if (rx_queues_count > 1 && priv->hw->mac->prog_mtl_rx_algorithms)
2409 priv->hw->mac->prog_mtl_rx_algorithms(priv->hw,
2410 priv->plat->rx_sched_algorithm);
2412 /* Configure MTL TX algorithms */
2413 if (tx_queues_count > 1 && priv->hw->mac->prog_mtl_tx_algorithms)
2414 priv->hw->mac->prog_mtl_tx_algorithms(priv->hw,
2415 priv->plat->tx_sched_algorithm);
2417 /* Configure CBS in AVB TX queues */
2418 if (tx_queues_count > 1 && priv->hw->mac->config_cbs)
2419 stmmac_configure_cbs(priv);
2421 /* Map RX MTL to DMA channels */
2422 if (priv->hw->mac->map_mtl_to_dma)
2423 stmmac_rx_queue_dma_chan_map(priv);
2425 /* Enable MAC RX Queues */
2426 if (priv->hw->mac->rx_queue_enable)
2427 stmmac_mac_enable_rx_queues(priv);
2429 /* Set RX priorities */
2430 if (rx_queues_count > 1 && priv->hw->mac->rx_queue_prio)
2431 stmmac_mac_config_rx_queues_prio(priv);
2433 /* Set TX priorities */
2434 if (tx_queues_count > 1 && priv->hw->mac->tx_queue_prio)
2435 stmmac_mac_config_tx_queues_prio(priv);
2437 /* Set RX routing */
2438 if (rx_queues_count > 1 && priv->hw->mac->rx_queue_routing)
2439 stmmac_mac_config_rx_queues_routing(priv);
2443 * stmmac_hw_setup - setup mac in a usable state.
2444 * @dev : pointer to the device structure.
2446 * this is the main function to setup the HW in a usable state because the
2447 * dma engine is reset, the core registers are configured (e.g. AXI,
2448 * Checksum features, timers). The DMA is ready to start receiving and
2451 * 0 on success and an appropriate (-)ve integer as defined in errno.h
2454 static int stmmac_hw_setup(struct net_device *dev, bool init_ptp)
2456 struct stmmac_priv *priv = netdev_priv(dev);
2457 u32 rx_cnt = priv->plat->rx_queues_to_use;
2458 u32 tx_cnt = priv->plat->tx_queues_to_use;
2462 /* DMA initialization and SW reset */
2463 ret = stmmac_init_dma_engine(priv);
2465 netdev_err(priv->dev, "%s: DMA engine initialization failed\n",
2470 /* Copy the MAC addr into the HW */
2471 priv->hw->mac->set_umac_addr(priv->hw, dev->dev_addr, 0);
2473 /* PS and related bits will be programmed according to the speed */
2474 if (priv->hw->pcs) {
2475 int speed = priv->plat->mac_port_sel_speed;
2477 if ((speed == SPEED_10) || (speed == SPEED_100) ||
2478 (speed == SPEED_1000)) {
2479 priv->hw->ps = speed;
2481 dev_warn(priv->device, "invalid port speed\n");
2486 /* Initialize the MAC Core */
2487 priv->hw->mac->core_init(priv->hw, dev->mtu);
2490 if (priv->synopsys_id >= DWMAC_CORE_4_00)
2491 stmmac_mtl_configuration(priv);
2493 ret = priv->hw->mac->rx_ipc(priv->hw);
2495 netdev_warn(priv->dev, "RX IPC Checksum Offload disabled\n");
2496 priv->plat->rx_coe = STMMAC_RX_COE_NONE;
2497 priv->hw->rx_csum = 0;
2500 /* Enable the MAC Rx/Tx */
2501 priv->hw->mac->set_mac(priv->ioaddr, true);
2503 /* Set the HW DMA mode and the COE */
2504 stmmac_dma_operation_mode(priv);
2506 stmmac_mmc_setup(priv);
2509 ret = clk_prepare_enable(priv->plat->clk_ptp_ref);
2511 netdev_warn(priv->dev, "failed to enable PTP reference clock: %d\n", ret);
2513 ret = stmmac_init_ptp(priv);
2514 if (ret == -EOPNOTSUPP)
2515 netdev_warn(priv->dev, "PTP not supported by HW\n");
2517 netdev_warn(priv->dev, "PTP init failed\n");
2520 #ifdef CONFIG_DEBUG_FS
2521 ret = stmmac_init_fs(dev);
2523 netdev_warn(priv->dev, "%s: failed debugFS registration\n",
2526 /* Start the ball rolling... */
2527 stmmac_start_all_dma(priv);
2529 priv->tx_lpi_timer = STMMAC_DEFAULT_TWT_LS;
2531 if ((priv->use_riwt) && (priv->hw->dma->rx_watchdog)) {
2532 priv->rx_riwt = MAX_DMA_RIWT;
2533 priv->hw->dma->rx_watchdog(priv->ioaddr, MAX_DMA_RIWT, rx_cnt);
2536 if (priv->hw->pcs && priv->hw->mac->pcs_ctrl_ane)
2537 priv->hw->mac->pcs_ctrl_ane(priv->hw, 1, priv->hw->ps, 0);
2539 /* set TX and RX rings length */
2540 stmmac_set_rings_length(priv);
2544 for (chan = 0; chan < tx_cnt; chan++)
2545 priv->hw->dma->enable_tso(priv->ioaddr, 1, chan);
2551 static void stmmac_hw_teardown(struct net_device *dev)
2553 struct stmmac_priv *priv = netdev_priv(dev);
2555 clk_disable_unprepare(priv->plat->clk_ptp_ref);
2559 * stmmac_open - open entry point of the driver
2560 * @dev : pointer to the device structure.
2562 * This function is the open entry point of the driver.
2564 * 0 on success and an appropriate (-)ve integer as defined in errno.h
2567 static int stmmac_open(struct net_device *dev)
2569 struct stmmac_priv *priv = netdev_priv(dev);
2572 stmmac_check_ether_addr(priv);
2574 if (priv->hw->pcs != STMMAC_PCS_RGMII &&
2575 priv->hw->pcs != STMMAC_PCS_TBI &&
2576 priv->hw->pcs != STMMAC_PCS_RTBI) {
2577 ret = stmmac_init_phy(dev);
2579 netdev_err(priv->dev,
2580 "%s: Cannot attach to PHY (error: %d)\n",
2586 /* Extra statistics */
2587 memset(&priv->xstats, 0, sizeof(struct stmmac_extra_stats));
2588 priv->xstats.threshold = tc;
2590 priv->dma_buf_sz = STMMAC_ALIGN(buf_sz);
2591 priv->rx_copybreak = STMMAC_RX_COPYBREAK;
2593 ret = alloc_dma_desc_resources(priv);
2595 netdev_err(priv->dev, "%s: DMA descriptors allocation failed\n",
2597 goto dma_desc_error;
2600 ret = init_dma_desc_rings(dev, GFP_KERNEL);
2602 netdev_err(priv->dev, "%s: DMA descriptors initialization failed\n",
2607 ret = stmmac_hw_setup(dev, true);
2609 netdev_err(priv->dev, "%s: Hw setup failed\n", __func__);
2613 stmmac_init_tx_coalesce(priv);
2616 phy_start(dev->phydev);
2618 /* Request the IRQ lines */
2619 ret = request_irq(dev->irq, stmmac_interrupt,
2620 IRQF_SHARED, dev->name, dev);
2621 if (unlikely(ret < 0)) {
2622 netdev_err(priv->dev,
2623 "%s: ERROR: allocating the IRQ %d (error: %d)\n",
2624 __func__, dev->irq, ret);
2628 /* Request the Wake IRQ in case of another line is used for WoL */
2629 if (priv->wol_irq != dev->irq) {
2630 ret = request_irq(priv->wol_irq, stmmac_interrupt,
2631 IRQF_SHARED, dev->name, dev);
2632 if (unlikely(ret < 0)) {
2633 netdev_err(priv->dev,
2634 "%s: ERROR: allocating the WoL IRQ %d (%d)\n",
2635 __func__, priv->wol_irq, ret);
2640 /* Request the IRQ lines */
2641 if (priv->lpi_irq > 0) {
2642 ret = request_irq(priv->lpi_irq, stmmac_interrupt, IRQF_SHARED,
2644 if (unlikely(ret < 0)) {
2645 netdev_err(priv->dev,
2646 "%s: ERROR: allocating the LPI IRQ %d (%d)\n",
2647 __func__, priv->lpi_irq, ret);
2652 stmmac_enable_all_queues(priv);
2653 stmmac_start_all_queues(priv);
2658 if (priv->wol_irq != dev->irq)
2659 free_irq(priv->wol_irq, dev);
2661 free_irq(dev->irq, dev);
2664 phy_stop(dev->phydev);
2666 del_timer_sync(&priv->txtimer);
2667 stmmac_hw_teardown(dev);
2669 free_dma_desc_resources(priv);
2672 phy_disconnect(dev->phydev);
2678 * stmmac_release - close entry point of the driver
2679 * @dev : device pointer.
2681 * This is the stop entry point of the driver.
2683 static int stmmac_release(struct net_device *dev)
2685 struct stmmac_priv *priv = netdev_priv(dev);
2687 if (priv->eee_enabled)
2688 del_timer_sync(&priv->eee_ctrl_timer);
2690 /* Stop and disconnect the PHY */
2692 phy_stop(dev->phydev);
2693 phy_disconnect(dev->phydev);
2696 stmmac_stop_all_queues(priv);
2698 stmmac_disable_all_queues(priv);
2700 del_timer_sync(&priv->txtimer);
2702 /* Free the IRQ lines */
2703 free_irq(dev->irq, dev);
2704 if (priv->wol_irq != dev->irq)
2705 free_irq(priv->wol_irq, dev);
2706 if (priv->lpi_irq > 0)
2707 free_irq(priv->lpi_irq, dev);
2709 /* Stop TX/RX DMA and clear the descriptors */
2710 stmmac_stop_all_dma(priv);
2712 /* Release and free the Rx/Tx resources */
2713 free_dma_desc_resources(priv);
2715 /* Disable the MAC Rx/Tx */
2716 priv->hw->mac->set_mac(priv->ioaddr, false);
2718 netif_carrier_off(dev);
2720 #ifdef CONFIG_DEBUG_FS
2721 stmmac_exit_fs(dev);
2724 stmmac_release_ptp(priv);
2730 * stmmac_tso_allocator - close entry point of the driver
2731 * @priv: driver private structure
2732 * @des: buffer start address
2733 * @total_len: total length to fill in descriptors
2734 * @last_segmant: condition for the last descriptor
2735 * @queue: TX queue index
2737 * This function fills descriptor and request new descriptors according to
2738 * buffer length to fill
2740 static void stmmac_tso_allocator(struct stmmac_priv *priv, unsigned int des,
2741 int total_len, bool last_segment, u32 queue)
2743 struct stmmac_tx_queue *tx_q = &priv->tx_queue[queue];
2744 struct dma_desc *desc;
2748 tmp_len = total_len;
2750 while (tmp_len > 0) {
2751 tx_q->cur_tx = STMMAC_GET_ENTRY(tx_q->cur_tx, DMA_TX_SIZE);
2752 desc = tx_q->dma_tx + tx_q->cur_tx;
2754 desc->des0 = cpu_to_le32(des + (total_len - tmp_len));
2755 buff_size = tmp_len >= TSO_MAX_BUFF_SIZE ?
2756 TSO_MAX_BUFF_SIZE : tmp_len;
2758 priv->hw->desc->prepare_tso_tx_desc(desc, 0, buff_size,
2760 (last_segment) && (tmp_len <= TSO_MAX_BUFF_SIZE),
2763 tmp_len -= TSO_MAX_BUFF_SIZE;
2768 * stmmac_tso_xmit - Tx entry point of the driver for oversized frames (TSO)
2769 * @skb : the socket buffer
2770 * @dev : device pointer
2771 * Description: this is the transmit function that is called on TSO frames
2772 * (support available on GMAC4 and newer chips).
2773 * Diagram below show the ring programming in case of TSO frames:
2777 * | DES0 |---> buffer1 = L2/L3/L4 header
2778 * | DES1 |---> TCP Payload (can continue on next descr...)
2779 * | DES2 |---> buffer 1 and 2 len
2780 * | DES3 |---> must set TSE, TCP hdr len-> [22:19]. TCP payload len [17:0]
2786 * | DES0 | --| Split TCP Payload on Buffers 1 and 2
2788 * | DES2 | --> buffer 1 and 2 len
2792 * mss is fixed when enable tso, so w/o programming the TDES3 ctx field.
2794 static netdev_tx_t stmmac_tso_xmit(struct sk_buff *skb, struct net_device *dev)
2796 struct dma_desc *desc, *first, *mss_desc = NULL;
2797 struct stmmac_priv *priv = netdev_priv(dev);
2798 int nfrags = skb_shinfo(skb)->nr_frags;
2799 u32 queue = skb_get_queue_mapping(skb);
2800 unsigned int first_entry, des;
2801 struct stmmac_tx_queue *tx_q;
2802 int tmp_pay_len = 0;
2807 tx_q = &priv->tx_queue[queue];
2809 /* Compute header lengths */
2810 proto_hdr_len = skb_transport_offset(skb) + tcp_hdrlen(skb);
2812 /* Desc availability based on threshold should be enough safe */
2813 if (unlikely(stmmac_tx_avail(priv, queue) <
2814 (((skb->len - proto_hdr_len) / TSO_MAX_BUFF_SIZE + 1)))) {
2815 if (!netif_tx_queue_stopped(netdev_get_tx_queue(dev, queue))) {
2816 netif_tx_stop_queue(netdev_get_tx_queue(priv->dev,
2818 /* This is a hard error, log it. */
2819 netdev_err(priv->dev,
2820 "%s: Tx Ring full when queue awake\n",
2823 return NETDEV_TX_BUSY;
2826 pay_len = skb_headlen(skb) - proto_hdr_len; /* no frags */
2828 mss = skb_shinfo(skb)->gso_size;
2830 /* set new MSS value if needed */
2831 if (mss != priv->mss) {
2832 mss_desc = tx_q->dma_tx + tx_q->cur_tx;
2833 priv->hw->desc->set_mss(mss_desc, mss);
2835 tx_q->cur_tx = STMMAC_GET_ENTRY(tx_q->cur_tx, DMA_TX_SIZE);
2838 if (netif_msg_tx_queued(priv)) {
2839 pr_info("%s: tcphdrlen %d, hdr_len %d, pay_len %d, mss %d\n",
2840 __func__, tcp_hdrlen(skb), proto_hdr_len, pay_len, mss);
2841 pr_info("\tskb->len %d, skb->data_len %d\n", skb->len,
2845 first_entry = tx_q->cur_tx;
2847 desc = tx_q->dma_tx + first_entry;
2850 /* first descriptor: fill Headers on Buf1 */
2851 des = dma_map_single(priv->device, skb->data, skb_headlen(skb),
2853 if (dma_mapping_error(priv->device, des))
2856 tx_q->tx_skbuff_dma[first_entry].buf = des;
2857 tx_q->tx_skbuff_dma[first_entry].len = skb_headlen(skb);
2859 first->des0 = cpu_to_le32(des);
2861 /* Fill start of payload in buff2 of first descriptor */
2863 first->des1 = cpu_to_le32(des + proto_hdr_len);
2865 /* If needed take extra descriptors to fill the remaining payload */
2866 tmp_pay_len = pay_len - TSO_MAX_BUFF_SIZE;
2868 stmmac_tso_allocator(priv, des, tmp_pay_len, (nfrags == 0), queue);
2870 /* Prepare fragments */
2871 for (i = 0; i < nfrags; i++) {
2872 const skb_frag_t *frag = &skb_shinfo(skb)->frags[i];
2874 des = skb_frag_dma_map(priv->device, frag, 0,
2875 skb_frag_size(frag),
2877 if (dma_mapping_error(priv->device, des))
2880 stmmac_tso_allocator(priv, des, skb_frag_size(frag),
2881 (i == nfrags - 1), queue);
2883 tx_q->tx_skbuff_dma[tx_q->cur_tx].buf = des;
2884 tx_q->tx_skbuff_dma[tx_q->cur_tx].len = skb_frag_size(frag);
2885 tx_q->tx_skbuff[tx_q->cur_tx] = NULL;
2886 tx_q->tx_skbuff_dma[tx_q->cur_tx].map_as_page = true;
2889 tx_q->tx_skbuff_dma[tx_q->cur_tx].last_segment = true;
2891 /* Only the last descriptor gets to point to the skb. */
2892 tx_q->tx_skbuff[tx_q->cur_tx] = skb;
2894 /* We've used all descriptors we need for this skb, however,
2895 * advance cur_tx so that it references a fresh descriptor.
2896 * ndo_start_xmit will fill this descriptor the next time it's
2897 * called and stmmac_tx_clean may clean up to this descriptor.
2899 tx_q->cur_tx = STMMAC_GET_ENTRY(tx_q->cur_tx, DMA_TX_SIZE);
2901 if (unlikely(stmmac_tx_avail(priv, queue) <= (MAX_SKB_FRAGS + 1))) {
2902 netif_dbg(priv, hw, priv->dev, "%s: stop transmitted packets\n",
2904 netif_tx_stop_queue(netdev_get_tx_queue(priv->dev, queue));
2907 dev->stats.tx_bytes += skb->len;
2908 priv->xstats.tx_tso_frames++;
2909 priv->xstats.tx_tso_nfrags += nfrags;
2911 /* Manage tx mitigation */
2912 priv->tx_count_frames += nfrags + 1;
2913 if (likely(priv->tx_coal_frames > priv->tx_count_frames)) {
2914 mod_timer(&priv->txtimer,
2915 STMMAC_COAL_TIMER(priv->tx_coal_timer));
2917 priv->tx_count_frames = 0;
2918 priv->hw->desc->set_tx_ic(desc);
2919 priv->xstats.tx_set_ic_bit++;
2922 skb_tx_timestamp(skb);
2924 if (unlikely((skb_shinfo(skb)->tx_flags & SKBTX_HW_TSTAMP) &&
2925 priv->hwts_tx_en)) {
2926 /* declare that device is doing timestamping */
2927 skb_shinfo(skb)->tx_flags |= SKBTX_IN_PROGRESS;
2928 priv->hw->desc->enable_tx_timestamp(first);
2931 /* Complete the first descriptor before granting the DMA */
2932 priv->hw->desc->prepare_tso_tx_desc(first, 1,
2935 1, tx_q->tx_skbuff_dma[first_entry].last_segment,
2936 tcp_hdrlen(skb) / 4, (skb->len - proto_hdr_len));
2938 /* If context desc is used to change MSS */
2940 priv->hw->desc->set_tx_owner(mss_desc);
2942 /* The own bit must be the latest setting done when prepare the
2943 * descriptor and then barrier is needed to make sure that
2944 * all is coherent before granting the DMA engine.
2948 if (netif_msg_pktdata(priv)) {
2949 pr_info("%s: curr=%d dirty=%d f=%d, e=%d, f_p=%p, nfrags %d\n",
2950 __func__, tx_q->cur_tx, tx_q->dirty_tx, first_entry,
2951 tx_q->cur_tx, first, nfrags);
2953 priv->hw->desc->display_ring((void *)tx_q->dma_tx, DMA_TX_SIZE,
2956 pr_info(">>> frame to be transmitted: ");
2957 print_pkt(skb->data, skb_headlen(skb));
2960 netdev_tx_sent_queue(netdev_get_tx_queue(dev, queue), skb->len);
2962 priv->hw->dma->set_tx_tail_ptr(priv->ioaddr, tx_q->tx_tail_addr,
2965 return NETDEV_TX_OK;
2968 dev_err(priv->device, "Tx dma map failed\n");
2970 priv->dev->stats.tx_dropped++;
2971 return NETDEV_TX_OK;
2975 * stmmac_xmit - Tx entry point of the driver
2976 * @skb : the socket buffer
2977 * @dev : device pointer
2978 * Description : this is the tx entry point of the driver.
2979 * It programs the chain or the ring and supports oversized frames
2982 static netdev_tx_t stmmac_xmit(struct sk_buff *skb, struct net_device *dev)
2984 struct stmmac_priv *priv = netdev_priv(dev);
2985 unsigned int nopaged_len = skb_headlen(skb);
2986 int i, csum_insertion = 0, is_jumbo = 0;
2987 u32 queue = skb_get_queue_mapping(skb);
2988 int nfrags = skb_shinfo(skb)->nr_frags;
2990 unsigned int first_entry;
2991 struct dma_desc *desc, *first;
2992 struct stmmac_tx_queue *tx_q;
2993 unsigned int enh_desc;
2996 tx_q = &priv->tx_queue[queue];
2998 /* Manage oversized TCP frames for GMAC4 device */
2999 if (skb_is_gso(skb) && priv->tso) {
3000 if (skb_shinfo(skb)->gso_type & (SKB_GSO_TCPV4 | SKB_GSO_TCPV6))
3001 return stmmac_tso_xmit(skb, dev);
3004 if (unlikely(stmmac_tx_avail(priv, queue) < nfrags + 1)) {
3005 if (!netif_tx_queue_stopped(netdev_get_tx_queue(dev, queue))) {
3006 netif_tx_stop_queue(netdev_get_tx_queue(priv->dev,
3008 /* This is a hard error, log it. */
3009 netdev_err(priv->dev,
3010 "%s: Tx Ring full when queue awake\n",
3013 return NETDEV_TX_BUSY;
3016 if (priv->tx_path_in_lpi_mode)
3017 stmmac_disable_eee_mode(priv);
3019 entry = tx_q->cur_tx;
3020 first_entry = entry;
3022 csum_insertion = (skb->ip_summed == CHECKSUM_PARTIAL);
3024 if (likely(priv->extend_desc))
3025 desc = (struct dma_desc *)(tx_q->dma_etx + entry);
3027 desc = tx_q->dma_tx + entry;
3031 enh_desc = priv->plat->enh_desc;
3032 /* To program the descriptors according to the size of the frame */
3034 is_jumbo = priv->hw->mode->is_jumbo_frm(skb->len, enh_desc);
3036 if (unlikely(is_jumbo) && likely(priv->synopsys_id <
3038 entry = priv->hw->mode->jumbo_frm(tx_q, skb, csum_insertion);
3039 if (unlikely(entry < 0))
3043 for (i = 0; i < nfrags; i++) {
3044 const skb_frag_t *frag = &skb_shinfo(skb)->frags[i];
3045 int len = skb_frag_size(frag);
3046 bool last_segment = (i == (nfrags - 1));
3048 entry = STMMAC_GET_ENTRY(entry, DMA_TX_SIZE);
3050 if (likely(priv->extend_desc))
3051 desc = (struct dma_desc *)(tx_q->dma_etx + entry);
3053 desc = tx_q->dma_tx + entry;
3055 des = skb_frag_dma_map(priv->device, frag, 0, len,
3057 if (dma_mapping_error(priv->device, des))
3058 goto dma_map_err; /* should reuse desc w/o issues */
3060 tx_q->tx_skbuff[entry] = NULL;
3062 tx_q->tx_skbuff_dma[entry].buf = des;
3063 if (unlikely(priv->synopsys_id >= DWMAC_CORE_4_00))
3064 desc->des0 = cpu_to_le32(des);
3066 desc->des2 = cpu_to_le32(des);
3068 tx_q->tx_skbuff_dma[entry].map_as_page = true;
3069 tx_q->tx_skbuff_dma[entry].len = len;
3070 tx_q->tx_skbuff_dma[entry].last_segment = last_segment;
3072 /* Prepare the descriptor and set the own bit too */
3073 priv->hw->desc->prepare_tx_desc(desc, 0, len, csum_insertion,
3074 priv->mode, 1, last_segment,
3078 /* Only the last descriptor gets to point to the skb. */
3079 tx_q->tx_skbuff[entry] = skb;
3081 /* We've used all descriptors we need for this skb, however,
3082 * advance cur_tx so that it references a fresh descriptor.
3083 * ndo_start_xmit will fill this descriptor the next time it's
3084 * called and stmmac_tx_clean may clean up to this descriptor.
3086 entry = STMMAC_GET_ENTRY(entry, DMA_TX_SIZE);
3087 tx_q->cur_tx = entry;
3089 if (netif_msg_pktdata(priv)) {
3092 netdev_dbg(priv->dev,
3093 "%s: curr=%d dirty=%d f=%d, e=%d, first=%p, nfrags=%d",
3094 __func__, tx_q->cur_tx, tx_q->dirty_tx, first_entry,
3095 entry, first, nfrags);
3097 if (priv->extend_desc)
3098 tx_head = (void *)tx_q->dma_etx;
3100 tx_head = (void *)tx_q->dma_tx;
3102 priv->hw->desc->display_ring(tx_head, DMA_TX_SIZE, false);
3104 netdev_dbg(priv->dev, ">>> frame to be transmitted: ");
3105 print_pkt(skb->data, skb->len);
3108 if (unlikely(stmmac_tx_avail(priv, queue) <= (MAX_SKB_FRAGS + 1))) {
3109 netif_dbg(priv, hw, priv->dev, "%s: stop transmitted packets\n",
3111 netif_tx_stop_queue(netdev_get_tx_queue(priv->dev, queue));
3114 dev->stats.tx_bytes += skb->len;
3116 /* According to the coalesce parameter the IC bit for the latest
3117 * segment is reset and the timer re-started to clean the tx status.
3118 * This approach takes care about the fragments: desc is the first
3119 * element in case of no SG.
3121 priv->tx_count_frames += nfrags + 1;
3122 if (likely(priv->tx_coal_frames > priv->tx_count_frames)) {
3123 mod_timer(&priv->txtimer,
3124 STMMAC_COAL_TIMER(priv->tx_coal_timer));
3126 priv->tx_count_frames = 0;
3127 priv->hw->desc->set_tx_ic(desc);
3128 priv->xstats.tx_set_ic_bit++;
3131 skb_tx_timestamp(skb);
3133 /* Ready to fill the first descriptor and set the OWN bit w/o any
3134 * problems because all the descriptors are actually ready to be
3135 * passed to the DMA engine.
3137 if (likely(!is_jumbo)) {
3138 bool last_segment = (nfrags == 0);
3140 des = dma_map_single(priv->device, skb->data,
3141 nopaged_len, DMA_TO_DEVICE);
3142 if (dma_mapping_error(priv->device, des))
3145 tx_q->tx_skbuff_dma[first_entry].buf = des;
3146 if (unlikely(priv->synopsys_id >= DWMAC_CORE_4_00))
3147 first->des0 = cpu_to_le32(des);
3149 first->des2 = cpu_to_le32(des);
3151 tx_q->tx_skbuff_dma[first_entry].len = nopaged_len;
3152 tx_q->tx_skbuff_dma[first_entry].last_segment = last_segment;
3154 if (unlikely((skb_shinfo(skb)->tx_flags & SKBTX_HW_TSTAMP) &&
3155 priv->hwts_tx_en)) {
3156 /* declare that device is doing timestamping */
3157 skb_shinfo(skb)->tx_flags |= SKBTX_IN_PROGRESS;
3158 priv->hw->desc->enable_tx_timestamp(first);
3161 /* Prepare the first descriptor setting the OWN bit too */
3162 priv->hw->desc->prepare_tx_desc(first, 1, nopaged_len,
3163 csum_insertion, priv->mode, 1,
3164 last_segment, skb->len);
3166 /* The own bit must be the latest setting done when prepare the
3167 * descriptor and then barrier is needed to make sure that
3168 * all is coherent before granting the DMA engine.
3173 netdev_tx_sent_queue(netdev_get_tx_queue(dev, queue), skb->len);
3175 if (priv->synopsys_id < DWMAC_CORE_4_00)
3176 priv->hw->dma->enable_dma_transmission(priv->ioaddr);
3178 priv->hw->dma->set_tx_tail_ptr(priv->ioaddr, tx_q->tx_tail_addr,
3181 return NETDEV_TX_OK;
3184 netdev_err(priv->dev, "Tx DMA map failed\n");
3186 priv->dev->stats.tx_dropped++;
3187 return NETDEV_TX_OK;
3190 static void stmmac_rx_vlan(struct net_device *dev, struct sk_buff *skb)
3192 struct ethhdr *ehdr;
3195 if ((dev->features & NETIF_F_HW_VLAN_CTAG_RX) ==
3196 NETIF_F_HW_VLAN_CTAG_RX &&
3197 !__vlan_get_tag(skb, &vlanid)) {
3198 /* pop the vlan tag */
3199 ehdr = (struct ethhdr *)skb->data;
3200 memmove(skb->data + VLAN_HLEN, ehdr, ETH_ALEN * 2);
3201 skb_pull(skb, VLAN_HLEN);
3202 __vlan_hwaccel_put_tag(skb, htons(ETH_P_8021Q), vlanid);
3207 static inline int stmmac_rx_threshold_count(struct stmmac_rx_queue *rx_q)
3209 if (rx_q->rx_zeroc_thresh < STMMAC_RX_THRESH)
3216 * stmmac_rx_refill - refill used skb preallocated buffers
3217 * @priv: driver private structure
3218 * @queue: RX queue index
3219 * Description : this is to reallocate the skb for the reception process
3220 * that is based on zero-copy.
3222 static inline void stmmac_rx_refill(struct stmmac_priv *priv, u32 queue)
3224 struct stmmac_rx_queue *rx_q = &priv->rx_queue[queue];
3225 int dirty = stmmac_rx_dirty(priv, queue);
3226 unsigned int entry = rx_q->dirty_rx;
3228 int bfsize = priv->dma_buf_sz;
3230 while (dirty-- > 0) {
3233 if (priv->extend_desc)
3234 p = (struct dma_desc *)(rx_q->dma_erx + entry);
3236 p = rx_q->dma_rx + entry;
3238 if (likely(!rx_q->rx_skbuff[entry])) {
3239 struct sk_buff *skb;
3241 skb = netdev_alloc_skb_ip_align(priv->dev, bfsize);
3242 if (unlikely(!skb)) {
3243 /* so for a while no zero-copy! */
3244 rx_q->rx_zeroc_thresh = STMMAC_RX_THRESH;
3245 if (unlikely(net_ratelimit()))
3246 dev_err(priv->device,
3247 "fail to alloc skb entry %d\n",
3252 rx_q->rx_skbuff[entry] = skb;
3253 rx_q->rx_skbuff_dma[entry] =
3254 dma_map_single(priv->device, skb->data, bfsize,
3256 if (dma_mapping_error(priv->device,
3257 rx_q->rx_skbuff_dma[entry])) {
3258 netdev_err(priv->dev, "Rx DMA map failed\n");
3263 if (unlikely(priv->synopsys_id >= DWMAC_CORE_4_00)) {
3264 p->des0 = cpu_to_le32(rx_q->rx_skbuff_dma[entry]);
3267 p->des2 = cpu_to_le32(rx_q->rx_skbuff_dma[entry]);
3269 if (priv->hw->mode->refill_desc3)
3270 priv->hw->mode->refill_desc3(rx_q, p);
3272 if (rx_q->rx_zeroc_thresh > 0)
3273 rx_q->rx_zeroc_thresh--;
3275 netif_dbg(priv, rx_status, priv->dev,
3276 "refill entry #%d\n", entry);
3280 if (unlikely(priv->synopsys_id >= DWMAC_CORE_4_00))
3281 priv->hw->desc->init_rx_desc(p, priv->use_riwt, 0, 0);
3283 priv->hw->desc->set_rx_owner(p);
3287 entry = STMMAC_GET_ENTRY(entry, DMA_RX_SIZE);
3289 rx_q->dirty_rx = entry;
3293 * stmmac_rx - manage the receive process
3294 * @priv: driver private structure
3295 * @limit: napi bugget
3296 * @queue: RX queue index.
3297 * Description : this the function called by the napi poll method.
3298 * It gets all the frames inside the ring.
3300 static int stmmac_rx(struct stmmac_priv *priv, int limit, u32 queue)
3302 struct stmmac_rx_queue *rx_q = &priv->rx_queue[queue];
3303 unsigned int entry = rx_q->cur_rx;
3304 int coe = priv->hw->rx_csum;
3305 unsigned int next_entry;
3306 unsigned int count = 0;
3308 if (netif_msg_rx_status(priv)) {
3311 netdev_dbg(priv->dev, "%s: descriptor ring:\n", __func__);
3312 if (priv->extend_desc)
3313 rx_head = (void *)rx_q->dma_erx;
3315 rx_head = (void *)rx_q->dma_rx;
3317 priv->hw->desc->display_ring(rx_head, DMA_RX_SIZE, true);
3319 while (count < limit) {
3322 struct dma_desc *np;
3324 if (priv->extend_desc)
3325 p = (struct dma_desc *)(rx_q->dma_erx + entry);
3327 p = rx_q->dma_rx + entry;
3329 /* read the status of the incoming frame */
3330 status = priv->hw->desc->rx_status(&priv->dev->stats,
3332 /* check if managed by the DMA otherwise go ahead */
3333 if (unlikely(status & dma_own))
3338 rx_q->cur_rx = STMMAC_GET_ENTRY(rx_q->cur_rx, DMA_RX_SIZE);
3339 next_entry = rx_q->cur_rx;
3341 if (priv->extend_desc)
3342 np = (struct dma_desc *)(rx_q->dma_erx + next_entry);
3344 np = rx_q->dma_rx + next_entry;
3348 if ((priv->extend_desc) && (priv->hw->desc->rx_extended_status))
3349 priv->hw->desc->rx_extended_status(&priv->dev->stats,
3353 if (unlikely(status == discard_frame)) {
3354 priv->dev->stats.rx_errors++;
3355 if (priv->hwts_rx_en && !priv->extend_desc) {
3356 /* DESC2 & DESC3 will be overwritten by device
3357 * with timestamp value, hence reinitialize
3358 * them in stmmac_rx_refill() function so that
3359 * device can reuse it.
3361 dev_kfree_skb_any(rx_q->rx_skbuff[entry]);
3362 rx_q->rx_skbuff[entry] = NULL;
3363 dma_unmap_single(priv->device,
3364 rx_q->rx_skbuff_dma[entry],
3369 struct sk_buff *skb;
3373 if (unlikely(priv->synopsys_id >= DWMAC_CORE_4_00))
3374 des = le32_to_cpu(p->des0);
3376 des = le32_to_cpu(p->des2);
3378 frame_len = priv->hw->desc->get_rx_frame_len(p, coe);
3380 /* If frame length is greater than skb buffer size
3381 * (preallocated during init) then the packet is
3384 if (frame_len > priv->dma_buf_sz) {
3385 netdev_err(priv->dev,
3386 "len %d larger than size (%d)\n",
3387 frame_len, priv->dma_buf_sz);
3388 priv->dev->stats.rx_length_errors++;
3392 /* ACS is set; GMAC core strips PAD/FCS for IEEE 802.3
3393 * Type frames (LLC/LLC-SNAP)
3395 if (unlikely(status != llc_snap))
3396 frame_len -= ETH_FCS_LEN;
3398 if (netif_msg_rx_status(priv)) {
3399 netdev_dbg(priv->dev, "\tdesc: %p [entry %d] buff=0x%x\n",
3401 if (frame_len > ETH_FRAME_LEN)
3402 netdev_dbg(priv->dev, "frame size %d, COE: %d\n",
3406 /* The zero-copy is always used for all the sizes
3407 * in case of GMAC4 because it needs
3408 * to refill the used descriptors, always.
3410 if (unlikely(!priv->plat->has_gmac4 &&
3411 ((frame_len < priv->rx_copybreak) ||
3412 stmmac_rx_threshold_count(rx_q)))) {
3413 skb = netdev_alloc_skb_ip_align(priv->dev,
3415 if (unlikely(!skb)) {
3416 if (net_ratelimit())
3417 dev_warn(priv->device,
3418 "packet dropped\n");
3419 priv->dev->stats.rx_dropped++;
3423 dma_sync_single_for_cpu(priv->device,
3427 skb_copy_to_linear_data(skb,
3429 rx_skbuff[entry]->data,
3432 skb_put(skb, frame_len);
3433 dma_sync_single_for_device(priv->device,
3438 skb = rx_q->rx_skbuff[entry];
3439 if (unlikely(!skb)) {
3440 netdev_err(priv->dev,
3441 "%s: Inconsistent Rx chain\n",
3443 priv->dev->stats.rx_dropped++;
3446 prefetch(skb->data - NET_IP_ALIGN);
3447 rx_q->rx_skbuff[entry] = NULL;
3448 rx_q->rx_zeroc_thresh++;
3450 skb_put(skb, frame_len);
3451 dma_unmap_single(priv->device,
3452 rx_q->rx_skbuff_dma[entry],
3457 if (netif_msg_pktdata(priv)) {
3458 netdev_dbg(priv->dev, "frame received (%dbytes)",
3460 print_pkt(skb->data, frame_len);
3463 stmmac_get_rx_hwtstamp(priv, p, np, skb);
3465 stmmac_rx_vlan(priv->dev, skb);
3467 skb->protocol = eth_type_trans(skb, priv->dev);
3470 skb_checksum_none_assert(skb);
3472 skb->ip_summed = CHECKSUM_UNNECESSARY;
3474 napi_gro_receive(&rx_q->napi, skb);
3476 priv->dev->stats.rx_packets++;
3477 priv->dev->stats.rx_bytes += frame_len;
3482 stmmac_rx_refill(priv, queue);
3484 priv->xstats.rx_pkt_n += count;
3490 * stmmac_poll - stmmac poll method (NAPI)
3491 * @napi : pointer to the napi structure.
3492 * @budget : maximum number of packets that the current CPU can receive from
3495 * To look at the incoming frames and clear the tx resources.
3497 static int stmmac_poll(struct napi_struct *napi, int budget)
3499 struct stmmac_rx_queue *rx_q =
3500 container_of(napi, struct stmmac_rx_queue, napi);
3501 struct stmmac_priv *priv = rx_q->priv_data;
3502 u32 tx_count = priv->plat->tx_queues_to_use;
3503 u32 chan = rx_q->queue_index;
3507 priv->xstats.napi_poll++;
3509 /* check all the queues */
3510 for (queue = 0; queue < tx_count; queue++)
3511 stmmac_tx_clean(priv, queue);
3513 work_done = stmmac_rx(priv, budget, rx_q->queue_index);
3514 if (work_done < budget) {
3515 napi_complete_done(napi, work_done);
3516 stmmac_enable_dma_irq(priv, chan);
3523 * @dev : Pointer to net device structure
3524 * Description: this function is called when a packet transmission fails to
3525 * complete within a reasonable time. The driver will mark the error in the
3526 * netdev structure and arrange for the device to be reset to a sane state
3527 * in order to transmit a new packet.
3529 static void stmmac_tx_timeout(struct net_device *dev)
3531 struct stmmac_priv *priv = netdev_priv(dev);
3532 u32 tx_count = priv->plat->tx_queues_to_use;
3535 /* Clear Tx resources and restart transmitting again */
3536 for (chan = 0; chan < tx_count; chan++)
3537 stmmac_tx_err(priv, chan);
3541 * stmmac_set_rx_mode - entry point for multicast addressing
3542 * @dev : pointer to the device structure
3544 * This function is a driver entry point which gets called by the kernel
3545 * whenever multicast addresses must be enabled/disabled.
3549 static void stmmac_set_rx_mode(struct net_device *dev)
3551 struct stmmac_priv *priv = netdev_priv(dev);
3553 priv->hw->mac->set_filter(priv->hw, dev);
3557 * stmmac_change_mtu - entry point to change MTU size for the device.
3558 * @dev : device pointer.
3559 * @new_mtu : the new MTU size for the device.
3560 * Description: the Maximum Transfer Unit (MTU) is used by the network layer
3561 * to drive packet transmission. Ethernet has an MTU of 1500 octets
3562 * (ETH_DATA_LEN). This value can be changed with ifconfig.
3564 * 0 on success and an appropriate (-)ve integer as defined in errno.h
3567 static int stmmac_change_mtu(struct net_device *dev, int new_mtu)
3569 struct stmmac_priv *priv = netdev_priv(dev);
3571 if (netif_running(dev)) {
3572 netdev_err(priv->dev, "must be stopped to change its MTU\n");
3578 netdev_update_features(dev);
3583 static netdev_features_t stmmac_fix_features(struct net_device *dev,
3584 netdev_features_t features)
3586 struct stmmac_priv *priv = netdev_priv(dev);
3588 if (priv->plat->rx_coe == STMMAC_RX_COE_NONE)
3589 features &= ~NETIF_F_RXCSUM;
3591 if (!priv->plat->tx_coe)
3592 features &= ~NETIF_F_CSUM_MASK;
3594 /* Some GMAC devices have a bugged Jumbo frame support that
3595 * needs to have the Tx COE disabled for oversized frames
3596 * (due to limited buffer sizes). In this case we disable
3597 * the TX csum insertion in the TDES and not use SF.
3599 if (priv->plat->bugged_jumbo && (dev->mtu > ETH_DATA_LEN))
3600 features &= ~NETIF_F_CSUM_MASK;
3602 /* Disable tso if asked by ethtool */
3603 if ((priv->plat->tso_en) && (priv->dma_cap.tsoen)) {
3604 if (features & NETIF_F_TSO)
3613 static int stmmac_set_features(struct net_device *netdev,
3614 netdev_features_t features)
3616 struct stmmac_priv *priv = netdev_priv(netdev);
3618 /* Keep the COE Type in case of csum is supporting */
3619 if (features & NETIF_F_RXCSUM)
3620 priv->hw->rx_csum = priv->plat->rx_coe;
3622 priv->hw->rx_csum = 0;
3623 /* No check needed because rx_coe has been set before and it will be
3624 * fixed in case of issue.
3626 priv->hw->mac->rx_ipc(priv->hw);
3632 * stmmac_interrupt - main ISR
3633 * @irq: interrupt number.
3634 * @dev_id: to pass the net device pointer.
3635 * Description: this is the main driver interrupt service routine.
3637 * o DMA service routine (to manage incoming frame reception and transmission
3639 * o Core interrupts to manage: remote wake-up, management counter, LPI
3642 static irqreturn_t stmmac_interrupt(int irq, void *dev_id)
3644 struct net_device *dev = (struct net_device *)dev_id;
3645 struct stmmac_priv *priv = netdev_priv(dev);
3646 u32 rx_cnt = priv->plat->rx_queues_to_use;
3647 u32 tx_cnt = priv->plat->tx_queues_to_use;
3651 queues_count = (rx_cnt > tx_cnt) ? rx_cnt : tx_cnt;
3654 pm_wakeup_event(priv->device, 0);
3656 if (unlikely(!dev)) {
3657 netdev_err(priv->dev, "%s: invalid dev pointer\n", __func__);
3661 /* To handle GMAC own interrupts */
3662 if ((priv->plat->has_gmac) || (priv->plat->has_gmac4)) {
3663 int status = priv->hw->mac->host_irq_status(priv->hw,
3666 if (unlikely(status)) {
3667 /* For LPI we need to save the tx status */
3668 if (status & CORE_IRQ_TX_PATH_IN_LPI_MODE)
3669 priv->tx_path_in_lpi_mode = true;
3670 if (status & CORE_IRQ_TX_PATH_EXIT_LPI_MODE)
3671 priv->tx_path_in_lpi_mode = false;
3674 if (priv->synopsys_id >= DWMAC_CORE_4_00) {
3675 for (queue = 0; queue < queues_count; queue++) {
3676 struct stmmac_rx_queue *rx_q =
3677 &priv->rx_queue[queue];
3680 priv->hw->mac->host_mtl_irq_status(priv->hw,
3683 if (status & CORE_IRQ_MTL_RX_OVERFLOW &&
3684 priv->hw->dma->set_rx_tail_ptr)
3685 priv->hw->dma->set_rx_tail_ptr(priv->ioaddr,
3691 /* PCS link status */
3692 if (priv->hw->pcs) {
3693 if (priv->xstats.pcs_link)
3694 netif_carrier_on(dev);
3696 netif_carrier_off(dev);
3700 /* To handle DMA interrupts */
3701 stmmac_dma_interrupt(priv);
3706 #ifdef CONFIG_NET_POLL_CONTROLLER
3707 /* Polling receive - used by NETCONSOLE and other diagnostic tools
3708 * to allow network I/O with interrupts disabled.
3710 static void stmmac_poll_controller(struct net_device *dev)
3712 disable_irq(dev->irq);
3713 stmmac_interrupt(dev->irq, dev);
3714 enable_irq(dev->irq);
3719 * stmmac_ioctl - Entry point for the Ioctl
3720 * @dev: Device pointer.
3721 * @rq: An IOCTL specefic structure, that can contain a pointer to
3722 * a proprietary structure used to pass information to the driver.
3723 * @cmd: IOCTL command
3725 * Currently it supports the phy_mii_ioctl(...) and HW time stamping.
3727 static int stmmac_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
3729 int ret = -EOPNOTSUPP;
3731 if (!netif_running(dev))
3740 ret = phy_mii_ioctl(dev->phydev, rq, cmd);
3743 ret = stmmac_hwtstamp_ioctl(dev, rq);
3752 static int stmmac_set_mac_address(struct net_device *ndev, void *addr)
3754 struct stmmac_priv *priv = netdev_priv(ndev);
3757 ret = eth_mac_addr(ndev, addr);
3761 priv->hw->mac->set_umac_addr(priv->hw, ndev->dev_addr, 0);
3766 #ifdef CONFIG_DEBUG_FS
3767 static struct dentry *stmmac_fs_dir;
3769 static void sysfs_display_ring(void *head, int size, int extend_desc,
3770 struct seq_file *seq)
3773 struct dma_extended_desc *ep = (struct dma_extended_desc *)head;
3774 struct dma_desc *p = (struct dma_desc *)head;
3776 for (i = 0; i < size; i++) {
3778 seq_printf(seq, "%d [0x%x]: 0x%x 0x%x 0x%x 0x%x\n",
3779 i, (unsigned int)virt_to_phys(ep),
3780 le32_to_cpu(ep->basic.des0),
3781 le32_to_cpu(ep->basic.des1),
3782 le32_to_cpu(ep->basic.des2),
3783 le32_to_cpu(ep->basic.des3));
3786 seq_printf(seq, "%d [0x%x]: 0x%x 0x%x 0x%x 0x%x\n",
3787 i, (unsigned int)virt_to_phys(p),
3788 le32_to_cpu(p->des0), le32_to_cpu(p->des1),
3789 le32_to_cpu(p->des2), le32_to_cpu(p->des3));
3792 seq_printf(seq, "\n");
3796 static int stmmac_sysfs_ring_read(struct seq_file *seq, void *v)
3798 struct net_device *dev = seq->private;
3799 struct stmmac_priv *priv = netdev_priv(dev);
3800 u32 rx_count = priv->plat->rx_queues_to_use;
3801 u32 tx_count = priv->plat->tx_queues_to_use;
3804 for (queue = 0; queue < rx_count; queue++) {
3805 struct stmmac_rx_queue *rx_q = &priv->rx_queue[queue];
3807 seq_printf(seq, "RX Queue %d:\n", queue);
3809 if (priv->extend_desc) {
3810 seq_printf(seq, "Extended descriptor ring:\n");
3811 sysfs_display_ring((void *)rx_q->dma_erx,
3812 DMA_RX_SIZE, 1, seq);
3814 seq_printf(seq, "Descriptor ring:\n");
3815 sysfs_display_ring((void *)rx_q->dma_rx,
3816 DMA_RX_SIZE, 0, seq);
3820 for (queue = 0; queue < tx_count; queue++) {
3821 struct stmmac_tx_queue *tx_q = &priv->tx_queue[queue];
3823 seq_printf(seq, "TX Queue %d:\n", queue);
3825 if (priv->extend_desc) {
3826 seq_printf(seq, "Extended descriptor ring:\n");
3827 sysfs_display_ring((void *)tx_q->dma_etx,
3828 DMA_TX_SIZE, 1, seq);
3830 seq_printf(seq, "Descriptor ring:\n");
3831 sysfs_display_ring((void *)tx_q->dma_tx,
3832 DMA_TX_SIZE, 0, seq);
3839 static int stmmac_sysfs_ring_open(struct inode *inode, struct file *file)
3841 return single_open(file, stmmac_sysfs_ring_read, inode->i_private);
3844 /* Debugfs files, should appear in /sys/kernel/debug/stmmaceth/eth0 */
3846 static const struct file_operations stmmac_rings_status_fops = {
3847 .owner = THIS_MODULE,
3848 .open = stmmac_sysfs_ring_open,
3850 .llseek = seq_lseek,
3851 .release = single_release,
3854 static int stmmac_sysfs_dma_cap_read(struct seq_file *seq, void *v)
3856 struct net_device *dev = seq->private;
3857 struct stmmac_priv *priv = netdev_priv(dev);
3859 if (!priv->hw_cap_support) {
3860 seq_printf(seq, "DMA HW features not supported\n");
3864 seq_printf(seq, "==============================\n");
3865 seq_printf(seq, "\tDMA HW features\n");
3866 seq_printf(seq, "==============================\n");
3868 seq_printf(seq, "\t10/100 Mbps: %s\n",
3869 (priv->dma_cap.mbps_10_100) ? "Y" : "N");
3870 seq_printf(seq, "\t1000 Mbps: %s\n",
3871 (priv->dma_cap.mbps_1000) ? "Y" : "N");
3872 seq_printf(seq, "\tHalf duplex: %s\n",
3873 (priv->dma_cap.half_duplex) ? "Y" : "N");
3874 seq_printf(seq, "\tHash Filter: %s\n",
3875 (priv->dma_cap.hash_filter) ? "Y" : "N");
3876 seq_printf(seq, "\tMultiple MAC address registers: %s\n",
3877 (priv->dma_cap.multi_addr) ? "Y" : "N");
3878 seq_printf(seq, "\tPCS (TBI/SGMII/RTBI PHY interfaces): %s\n",
3879 (priv->dma_cap.pcs) ? "Y" : "N");
3880 seq_printf(seq, "\tSMA (MDIO) Interface: %s\n",
3881 (priv->dma_cap.sma_mdio) ? "Y" : "N");
3882 seq_printf(seq, "\tPMT Remote wake up: %s\n",
3883 (priv->dma_cap.pmt_remote_wake_up) ? "Y" : "N");
3884 seq_printf(seq, "\tPMT Magic Frame: %s\n",
3885 (priv->dma_cap.pmt_magic_frame) ? "Y" : "N");
3886 seq_printf(seq, "\tRMON module: %s\n",
3887 (priv->dma_cap.rmon) ? "Y" : "N");
3888 seq_printf(seq, "\tIEEE 1588-2002 Time Stamp: %s\n",
3889 (priv->dma_cap.time_stamp) ? "Y" : "N");
3890 seq_printf(seq, "\tIEEE 1588-2008 Advanced Time Stamp: %s\n",
3891 (priv->dma_cap.atime_stamp) ? "Y" : "N");
3892 seq_printf(seq, "\t802.3az - Energy-Efficient Ethernet (EEE): %s\n",
3893 (priv->dma_cap.eee) ? "Y" : "N");
3894 seq_printf(seq, "\tAV features: %s\n", (priv->dma_cap.av) ? "Y" : "N");
3895 seq_printf(seq, "\tChecksum Offload in TX: %s\n",
3896 (priv->dma_cap.tx_coe) ? "Y" : "N");
3897 if (priv->synopsys_id >= DWMAC_CORE_4_00) {
3898 seq_printf(seq, "\tIP Checksum Offload in RX: %s\n",
3899 (priv->dma_cap.rx_coe) ? "Y" : "N");
3901 seq_printf(seq, "\tIP Checksum Offload (type1) in RX: %s\n",
3902 (priv->dma_cap.rx_coe_type1) ? "Y" : "N");
3903 seq_printf(seq, "\tIP Checksum Offload (type2) in RX: %s\n",
3904 (priv->dma_cap.rx_coe_type2) ? "Y" : "N");
3906 seq_printf(seq, "\tRXFIFO > 2048bytes: %s\n",
3907 (priv->dma_cap.rxfifo_over_2048) ? "Y" : "N");
3908 seq_printf(seq, "\tNumber of Additional RX channel: %d\n",
3909 priv->dma_cap.number_rx_channel);
3910 seq_printf(seq, "\tNumber of Additional TX channel: %d\n",
3911 priv->dma_cap.number_tx_channel);
3912 seq_printf(seq, "\tEnhanced descriptors: %s\n",
3913 (priv->dma_cap.enh_desc) ? "Y" : "N");
3918 static int stmmac_sysfs_dma_cap_open(struct inode *inode, struct file *file)
3920 return single_open(file, stmmac_sysfs_dma_cap_read, inode->i_private);
3923 static const struct file_operations stmmac_dma_cap_fops = {
3924 .owner = THIS_MODULE,
3925 .open = stmmac_sysfs_dma_cap_open,
3927 .llseek = seq_lseek,
3928 .release = single_release,
3931 static int stmmac_init_fs(struct net_device *dev)
3933 struct stmmac_priv *priv = netdev_priv(dev);
3935 /* Create per netdev entries */
3936 priv->dbgfs_dir = debugfs_create_dir(dev->name, stmmac_fs_dir);
3938 if (!priv->dbgfs_dir || IS_ERR(priv->dbgfs_dir)) {
3939 netdev_err(priv->dev, "ERROR failed to create debugfs directory\n");
3944 /* Entry to report DMA RX/TX rings */
3945 priv->dbgfs_rings_status =
3946 debugfs_create_file("descriptors_status", S_IRUGO,
3947 priv->dbgfs_dir, dev,
3948 &stmmac_rings_status_fops);
3950 if (!priv->dbgfs_rings_status || IS_ERR(priv->dbgfs_rings_status)) {
3951 netdev_err(priv->dev, "ERROR creating stmmac ring debugfs file\n");
3952 debugfs_remove_recursive(priv->dbgfs_dir);
3957 /* Entry to report the DMA HW features */
3958 priv->dbgfs_dma_cap = debugfs_create_file("dma_cap", S_IRUGO,
3960 dev, &stmmac_dma_cap_fops);
3962 if (!priv->dbgfs_dma_cap || IS_ERR(priv->dbgfs_dma_cap)) {
3963 netdev_err(priv->dev, "ERROR creating stmmac MMC debugfs file\n");
3964 debugfs_remove_recursive(priv->dbgfs_dir);
3972 static void stmmac_exit_fs(struct net_device *dev)
3974 struct stmmac_priv *priv = netdev_priv(dev);
3976 debugfs_remove_recursive(priv->dbgfs_dir);
3978 #endif /* CONFIG_DEBUG_FS */
3980 static const struct net_device_ops stmmac_netdev_ops = {
3981 .ndo_open = stmmac_open,
3982 .ndo_start_xmit = stmmac_xmit,
3983 .ndo_stop = stmmac_release,
3984 .ndo_change_mtu = stmmac_change_mtu,
3985 .ndo_fix_features = stmmac_fix_features,
3986 .ndo_set_features = stmmac_set_features,
3987 .ndo_set_rx_mode = stmmac_set_rx_mode,
3988 .ndo_tx_timeout = stmmac_tx_timeout,
3989 .ndo_do_ioctl = stmmac_ioctl,
3990 #ifdef CONFIG_NET_POLL_CONTROLLER
3991 .ndo_poll_controller = stmmac_poll_controller,
3993 .ndo_set_mac_address = stmmac_set_mac_address,
3997 * stmmac_hw_init - Init the MAC device
3998 * @priv: driver private structure
3999 * Description: this function is to configure the MAC device according to
4000 * some platform parameters or the HW capability register. It prepares the
4001 * driver to use either ring or chain modes and to setup either enhanced or
4002 * normal descriptors.
4004 static int stmmac_hw_init(struct stmmac_priv *priv)
4006 struct mac_device_info *mac;
4008 /* Identify the MAC HW device */
4009 if (priv->plat->setup) {
4010 mac = priv->plat->setup(priv);
4011 } else if (priv->plat->has_gmac) {
4012 priv->dev->priv_flags |= IFF_UNICAST_FLT;
4013 mac = dwmac1000_setup(priv->ioaddr,
4014 priv->plat->multicast_filter_bins,
4015 priv->plat->unicast_filter_entries,
4016 &priv->synopsys_id);
4017 } else if (priv->plat->has_gmac4) {
4018 priv->dev->priv_flags |= IFF_UNICAST_FLT;
4019 mac = dwmac4_setup(priv->ioaddr,
4020 priv->plat->multicast_filter_bins,
4021 priv->plat->unicast_filter_entries,
4022 &priv->synopsys_id);
4024 mac = dwmac100_setup(priv->ioaddr, &priv->synopsys_id);
4031 /* dwmac-sun8i only work in chain mode */
4032 if (priv->plat->has_sun8i)
4035 /* To use the chained or ring mode */
4036 if (priv->synopsys_id >= DWMAC_CORE_4_00) {
4037 priv->hw->mode = &dwmac4_ring_mode_ops;
4040 priv->hw->mode = &chain_mode_ops;
4041 dev_info(priv->device, "Chain mode enabled\n");
4042 priv->mode = STMMAC_CHAIN_MODE;
4044 priv->hw->mode = &ring_mode_ops;
4045 dev_info(priv->device, "Ring mode enabled\n");
4046 priv->mode = STMMAC_RING_MODE;
4050 /* Get the HW capability (new GMAC newer than 3.50a) */
4051 priv->hw_cap_support = stmmac_get_hw_features(priv);
4052 if (priv->hw_cap_support) {
4053 dev_info(priv->device, "DMA HW capability register supported\n");
4055 /* We can override some gmac/dma configuration fields: e.g.
4056 * enh_desc, tx_coe (e.g. that are passed through the
4057 * platform) with the values from the HW capability
4058 * register (if supported).
4060 priv->plat->enh_desc = priv->dma_cap.enh_desc;
4061 priv->plat->pmt = priv->dma_cap.pmt_remote_wake_up;
4062 priv->hw->pmt = priv->plat->pmt;
4064 /* TXCOE doesn't work in thresh DMA mode */
4065 if (priv->plat->force_thresh_dma_mode)
4066 priv->plat->tx_coe = 0;
4068 priv->plat->tx_coe = priv->dma_cap.tx_coe;
4070 /* In case of GMAC4 rx_coe is from HW cap register. */
4071 priv->plat->rx_coe = priv->dma_cap.rx_coe;
4073 if (priv->dma_cap.rx_coe_type2)
4074 priv->plat->rx_coe = STMMAC_RX_COE_TYPE2;
4075 else if (priv->dma_cap.rx_coe_type1)
4076 priv->plat->rx_coe = STMMAC_RX_COE_TYPE1;
4079 dev_info(priv->device, "No HW DMA feature register supported\n");
4082 /* To use alternate (extended), normal or GMAC4 descriptor structures */
4083 if (priv->synopsys_id >= DWMAC_CORE_4_00)
4084 priv->hw->desc = &dwmac4_desc_ops;
4086 stmmac_selec_desc_mode(priv);
4088 if (priv->plat->rx_coe) {
4089 priv->hw->rx_csum = priv->plat->rx_coe;
4090 dev_info(priv->device, "RX Checksum Offload Engine supported\n");
4091 if (priv->synopsys_id < DWMAC_CORE_4_00)
4092 dev_info(priv->device, "COE Type %d\n", priv->hw->rx_csum);
4094 if (priv->plat->tx_coe)
4095 dev_info(priv->device, "TX Checksum insertion supported\n");
4097 if (priv->plat->pmt) {
4098 dev_info(priv->device, "Wake-Up On Lan supported\n");
4099 device_set_wakeup_capable(priv->device, 1);
4102 if (priv->dma_cap.tsoen)
4103 dev_info(priv->device, "TSO supported\n");
4110 * @device: device pointer
4111 * @plat_dat: platform data pointer
4112 * @res: stmmac resource pointer
4113 * Description: this is the main probe function used to
4114 * call the alloc_etherdev, allocate the priv structure.
4116 * returns 0 on success, otherwise errno.
4118 int stmmac_dvr_probe(struct device *device,
4119 struct plat_stmmacenet_data *plat_dat,
4120 struct stmmac_resources *res)
4122 struct net_device *ndev = NULL;
4123 struct stmmac_priv *priv;
4127 ndev = alloc_etherdev_mqs(sizeof(struct stmmac_priv),
4133 SET_NETDEV_DEV(ndev, device);
4135 priv = netdev_priv(ndev);
4136 priv->device = device;
4139 stmmac_set_ethtool_ops(ndev);
4140 priv->pause = pause;
4141 priv->plat = plat_dat;
4142 priv->ioaddr = res->addr;
4143 priv->dev->base_addr = (unsigned long)res->addr;
4145 priv->dev->irq = res->irq;
4146 priv->wol_irq = res->wol_irq;
4147 priv->lpi_irq = res->lpi_irq;
4150 memcpy(priv->dev->dev_addr, res->mac, ETH_ALEN);
4152 dev_set_drvdata(device, priv->dev);
4154 /* Verify driver arguments */
4155 stmmac_verify_args();
4157 /* Override with kernel parameters if supplied XXX CRS XXX
4158 * this needs to have multiple instances
4160 if ((phyaddr >= 0) && (phyaddr <= 31))
4161 priv->plat->phy_addr = phyaddr;
4163 if (priv->plat->stmmac_rst) {
4164 ret = reset_control_assert(priv->plat->stmmac_rst);
4165 reset_control_deassert(priv->plat->stmmac_rst);
4166 /* Some reset controllers have only reset callback instead of
4167 * assert + deassert callbacks pair.
4169 if (ret == -ENOTSUPP)
4170 reset_control_reset(priv->plat->stmmac_rst);
4173 /* Init MAC and get the capabilities */
4174 ret = stmmac_hw_init(priv);
4178 /* Configure real RX and TX queues */
4179 netif_set_real_num_rx_queues(ndev, priv->plat->rx_queues_to_use);
4180 netif_set_real_num_tx_queues(ndev, priv->plat->tx_queues_to_use);
4182 ndev->netdev_ops = &stmmac_netdev_ops;
4184 ndev->hw_features = NETIF_F_SG | NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM |
4187 if ((priv->plat->tso_en) && (priv->dma_cap.tsoen)) {
4188 ndev->hw_features |= NETIF_F_TSO | NETIF_F_TSO6;
4190 dev_info(priv->device, "TSO feature enabled\n");
4192 ndev->features |= ndev->hw_features | NETIF_F_HIGHDMA;
4193 ndev->watchdog_timeo = msecs_to_jiffies(watchdog);
4194 #ifdef STMMAC_VLAN_TAG_USED
4195 /* Both mac100 and gmac support receive VLAN tag detection */
4196 ndev->features |= NETIF_F_HW_VLAN_CTAG_RX;
4198 priv->msg_enable = netif_msg_init(debug, default_msg_level);
4200 /* MTU range: 46 - hw-specific max */
4201 ndev->min_mtu = ETH_ZLEN - ETH_HLEN;
4202 if ((priv->plat->enh_desc) || (priv->synopsys_id >= DWMAC_CORE_4_00))
4203 ndev->max_mtu = JUMBO_LEN;
4205 ndev->max_mtu = SKB_MAX_HEAD(NET_SKB_PAD + NET_IP_ALIGN);
4206 /* Will not overwrite ndev->max_mtu if plat->maxmtu > ndev->max_mtu
4207 * as well as plat->maxmtu < ndev->min_mtu which is a invalid range.
4209 if ((priv->plat->maxmtu < ndev->max_mtu) &&
4210 (priv->plat->maxmtu >= ndev->min_mtu))
4211 ndev->max_mtu = priv->plat->maxmtu;
4212 else if (priv->plat->maxmtu < ndev->min_mtu)
4213 dev_warn(priv->device,
4214 "%s: warning: maxmtu having invalid value (%d)\n",
4215 __func__, priv->plat->maxmtu);
4218 priv->flow_ctrl = FLOW_AUTO; /* RX/TX pause on */
4220 /* Rx Watchdog is available in the COREs newer than the 3.40.
4221 * In some case, for example on bugged HW this feature
4222 * has to be disable and this can be done by passing the
4223 * riwt_off field from the platform.
4225 if ((priv->synopsys_id >= DWMAC_CORE_3_50) && (!priv->plat->riwt_off)) {
4227 dev_info(priv->device,
4228 "Enable RX Mitigation via HW Watchdog Timer\n");
4231 for (queue = 0; queue < priv->plat->rx_queues_to_use; queue++) {
4232 struct stmmac_rx_queue *rx_q = &priv->rx_queue[queue];
4234 netif_napi_add(ndev, &rx_q->napi, stmmac_poll,
4235 (8 * priv->plat->rx_queues_to_use));
4238 spin_lock_init(&priv->lock);
4240 /* If a specific clk_csr value is passed from the platform
4241 * this means that the CSR Clock Range selection cannot be
4242 * changed at run-time and it is fixed. Viceversa the driver'll try to
4243 * set the MDC clock dynamically according to the csr actual
4246 if (!priv->plat->clk_csr)
4247 stmmac_clk_csr_set(priv);
4249 priv->clk_csr = priv->plat->clk_csr;
4251 stmmac_check_pcs_mode(priv);
4253 if (priv->hw->pcs != STMMAC_PCS_RGMII &&
4254 priv->hw->pcs != STMMAC_PCS_TBI &&
4255 priv->hw->pcs != STMMAC_PCS_RTBI) {
4256 /* MDIO bus Registration */
4257 ret = stmmac_mdio_register(ndev);
4259 dev_err(priv->device,
4260 "%s: MDIO bus (id: %d) registration failed",
4261 __func__, priv->plat->bus_id);
4262 goto error_mdio_register;
4266 ret = register_netdev(ndev);
4268 dev_err(priv->device, "%s: ERROR %i registering the device\n",
4270 goto error_netdev_register;
4275 error_netdev_register:
4276 if (priv->hw->pcs != STMMAC_PCS_RGMII &&
4277 priv->hw->pcs != STMMAC_PCS_TBI &&
4278 priv->hw->pcs != STMMAC_PCS_RTBI)
4279 stmmac_mdio_unregister(ndev);
4280 error_mdio_register:
4281 for (queue = 0; queue < priv->plat->rx_queues_to_use; queue++) {
4282 struct stmmac_rx_queue *rx_q = &priv->rx_queue[queue];
4284 netif_napi_del(&rx_q->napi);
4291 EXPORT_SYMBOL_GPL(stmmac_dvr_probe);
4295 * @dev: device pointer
4296 * Description: this function resets the TX/RX processes, disables the MAC RX/TX
4297 * changes the link status, releases the DMA descriptor rings.
4299 int stmmac_dvr_remove(struct device *dev)
4301 struct net_device *ndev = dev_get_drvdata(dev);
4302 struct stmmac_priv *priv = netdev_priv(ndev);
4304 netdev_info(priv->dev, "%s: removing driver", __func__);
4306 stmmac_stop_all_dma(priv);
4308 priv->hw->mac->set_mac(priv->ioaddr, false);
4309 netif_carrier_off(ndev);
4310 unregister_netdev(ndev);
4311 if (priv->plat->stmmac_rst)
4312 reset_control_assert(priv->plat->stmmac_rst);
4313 clk_disable_unprepare(priv->plat->pclk);
4314 clk_disable_unprepare(priv->plat->stmmac_clk);
4315 if (priv->hw->pcs != STMMAC_PCS_RGMII &&
4316 priv->hw->pcs != STMMAC_PCS_TBI &&
4317 priv->hw->pcs != STMMAC_PCS_RTBI)
4318 stmmac_mdio_unregister(ndev);
4323 EXPORT_SYMBOL_GPL(stmmac_dvr_remove);
4326 * stmmac_suspend - suspend callback
4327 * @dev: device pointer
4328 * Description: this is the function to suspend the device and it is called
4329 * by the platform driver to stop the network queue, release the resources,
4330 * program the PMT register (for WoL), clean and release driver resources.
4332 int stmmac_suspend(struct device *dev)
4334 struct net_device *ndev = dev_get_drvdata(dev);
4335 struct stmmac_priv *priv = netdev_priv(ndev);
4336 unsigned long flags;
4338 if (!ndev || !netif_running(ndev))
4342 phy_stop(ndev->phydev);
4344 spin_lock_irqsave(&priv->lock, flags);
4346 netif_device_detach(ndev);
4347 stmmac_stop_all_queues(priv);
4349 stmmac_disable_all_queues(priv);
4351 /* Stop TX/RX DMA */
4352 stmmac_stop_all_dma(priv);
4354 /* Enable Power down mode by programming the PMT regs */
4355 if (device_may_wakeup(priv->device)) {
4356 priv->hw->mac->pmt(priv->hw, priv->wolopts);
4359 priv->hw->mac->set_mac(priv->ioaddr, false);
4360 pinctrl_pm_select_sleep_state(priv->device);
4361 /* Disable clock in case of PWM is off */
4362 clk_disable(priv->plat->pclk);
4363 clk_disable(priv->plat->stmmac_clk);
4365 spin_unlock_irqrestore(&priv->lock, flags);
4367 priv->oldlink = false;
4368 priv->speed = SPEED_UNKNOWN;
4369 priv->oldduplex = DUPLEX_UNKNOWN;
4372 EXPORT_SYMBOL_GPL(stmmac_suspend);
4375 * stmmac_reset_queues_param - reset queue parameters
4376 * @dev: device pointer
4378 static void stmmac_reset_queues_param(struct stmmac_priv *priv)
4380 u32 rx_cnt = priv->plat->rx_queues_to_use;
4381 u32 tx_cnt = priv->plat->tx_queues_to_use;
4384 for (queue = 0; queue < rx_cnt; queue++) {
4385 struct stmmac_rx_queue *rx_q = &priv->rx_queue[queue];
4391 for (queue = 0; queue < tx_cnt; queue++) {
4392 struct stmmac_tx_queue *tx_q = &priv->tx_queue[queue];
4400 * stmmac_resume - resume callback
4401 * @dev: device pointer
4402 * Description: when resume this function is invoked to setup the DMA and CORE
4403 * in a usable state.
4405 int stmmac_resume(struct device *dev)
4407 struct net_device *ndev = dev_get_drvdata(dev);
4408 struct stmmac_priv *priv = netdev_priv(ndev);
4409 unsigned long flags;
4411 if (!netif_running(ndev))
4414 /* Power Down bit, into the PM register, is cleared
4415 * automatically as soon as a magic packet or a Wake-up frame
4416 * is received. Anyway, it's better to manually clear
4417 * this bit because it can generate problems while resuming
4418 * from another devices (e.g. serial console).
4420 if (device_may_wakeup(priv->device)) {
4421 spin_lock_irqsave(&priv->lock, flags);
4422 priv->hw->mac->pmt(priv->hw, 0);
4423 spin_unlock_irqrestore(&priv->lock, flags);
4426 pinctrl_pm_select_default_state(priv->device);
4427 /* enable the clk previously disabled */
4428 clk_enable(priv->plat->stmmac_clk);
4429 clk_enable(priv->plat->pclk);
4430 /* reset the phy so that it's ready */
4432 stmmac_mdio_reset(priv->mii);
4435 netif_device_attach(ndev);
4437 spin_lock_irqsave(&priv->lock, flags);
4439 stmmac_reset_queues_param(priv);
4441 /* reset private mss value to force mss context settings at
4442 * next tso xmit (only used for gmac4).
4446 stmmac_clear_descriptors(priv);
4448 stmmac_hw_setup(ndev, false);
4449 stmmac_init_tx_coalesce(priv);
4450 stmmac_set_rx_mode(ndev);
4452 stmmac_enable_all_queues(priv);
4454 stmmac_start_all_queues(priv);
4456 spin_unlock_irqrestore(&priv->lock, flags);
4459 phy_start(ndev->phydev);
4463 EXPORT_SYMBOL_GPL(stmmac_resume);
4466 static int __init stmmac_cmdline_opt(char *str)
4472 while ((opt = strsep(&str, ",")) != NULL) {
4473 if (!strncmp(opt, "debug:", 6)) {
4474 if (kstrtoint(opt + 6, 0, &debug))
4476 } else if (!strncmp(opt, "phyaddr:", 8)) {
4477 if (kstrtoint(opt + 8, 0, &phyaddr))
4479 } else if (!strncmp(opt, "buf_sz:", 7)) {
4480 if (kstrtoint(opt + 7, 0, &buf_sz))
4482 } else if (!strncmp(opt, "tc:", 3)) {
4483 if (kstrtoint(opt + 3, 0, &tc))
4485 } else if (!strncmp(opt, "watchdog:", 9)) {
4486 if (kstrtoint(opt + 9, 0, &watchdog))
4488 } else if (!strncmp(opt, "flow_ctrl:", 10)) {
4489 if (kstrtoint(opt + 10, 0, &flow_ctrl))
4491 } else if (!strncmp(opt, "pause:", 6)) {
4492 if (kstrtoint(opt + 6, 0, &pause))
4494 } else if (!strncmp(opt, "eee_timer:", 10)) {
4495 if (kstrtoint(opt + 10, 0, &eee_timer))
4497 } else if (!strncmp(opt, "chain_mode:", 11)) {
4498 if (kstrtoint(opt + 11, 0, &chain_mode))
4505 pr_err("%s: ERROR broken module parameter conversion", __func__);
4509 __setup("stmmaceth=", stmmac_cmdline_opt);
4512 static int __init stmmac_init(void)
4514 #ifdef CONFIG_DEBUG_FS
4515 /* Create debugfs main directory if it doesn't exist yet */
4516 if (!stmmac_fs_dir) {
4517 stmmac_fs_dir = debugfs_create_dir(STMMAC_RESOURCE_NAME, NULL);
4519 if (!stmmac_fs_dir || IS_ERR(stmmac_fs_dir)) {
4520 pr_err("ERROR %s, debugfs create directory failed\n",
4521 STMMAC_RESOURCE_NAME);
4531 static void __exit stmmac_exit(void)
4533 #ifdef CONFIG_DEBUG_FS
4534 debugfs_remove_recursive(stmmac_fs_dir);
4538 module_init(stmmac_init)
4539 module_exit(stmmac_exit)
4541 MODULE_DESCRIPTION("STMMAC 10/100/1000 Ethernet device driver");
4542 MODULE_AUTHOR("Giuseppe Cavallaro <peppe.cavallaro@st.com>");
4543 MODULE_LICENSE("GPL");