ide: add ->cable_detect method to ide_hwif_t
[sfrench/cifs-2.6.git] / drivers / ide / pci / cmd64x.c
1 /*
2  * cmd64x.c: Enable interrupts at initialization time on Ultra/PCI machines.
3  *           Due to massive hardware bugs, UltraDMA is only supported
4  *           on the 646U2 and not on the 646U.
5  *
6  * Copyright (C) 1998           Eddie C. Dost  (ecd@skynet.be)
7  * Copyright (C) 1998           David S. Miller (davem@redhat.com)
8  *
9  * Copyright (C) 1999-2002      Andre Hedrick <andre@linux-ide.org>
10  * Copyright (C) 2007           MontaVista Software, Inc. <source@mvista.com>
11  */
12
13 #include <linux/module.h>
14 #include <linux/types.h>
15 #include <linux/pci.h>
16 #include <linux/delay.h>
17 #include <linux/hdreg.h>
18 #include <linux/ide.h>
19 #include <linux/init.h>
20
21 #include <asm/io.h>
22
23 #define CMD_DEBUG 0
24
25 #if CMD_DEBUG
26 #define cmdprintk(x...) printk(x)
27 #else
28 #define cmdprintk(x...)
29 #endif
30
31 /*
32  * CMD64x specific registers definition.
33  */
34 #define CFR             0x50
35 #define   CFR_INTR_CH0          0x04
36
37 #define CMDTIM          0x52
38 #define ARTTIM0         0x53
39 #define DRWTIM0         0x54
40 #define ARTTIM1         0x55
41 #define DRWTIM1         0x56
42 #define ARTTIM23        0x57
43 #define   ARTTIM23_DIS_RA2      0x04
44 #define   ARTTIM23_DIS_RA3      0x08
45 #define   ARTTIM23_INTR_CH1     0x10
46 #define DRWTIM2         0x58
47 #define BRST            0x59
48 #define DRWTIM3         0x5b
49
50 #define BMIDECR0        0x70
51 #define MRDMODE         0x71
52 #define   MRDMODE_INTR_CH0      0x04
53 #define   MRDMODE_INTR_CH1      0x08
54 #define UDIDETCR0       0x73
55 #define DTPR0           0x74
56 #define BMIDECR1        0x78
57 #define BMIDECSR        0x79
58 #define UDIDETCR1       0x7B
59 #define DTPR1           0x7C
60
61 static u8 quantize_timing(int timing, int quant)
62 {
63         return (timing + quant - 1) / quant;
64 }
65
66 /*
67  * This routine calculates active/recovery counts and then writes them into
68  * the chipset registers.
69  */
70 static void program_cycle_times (ide_drive_t *drive, int cycle_time, int active_time)
71 {
72         struct pci_dev *dev     = to_pci_dev(drive->hwif->dev);
73         int clock_time          = 1000 / system_bus_clock();
74         u8  cycle_count, active_count, recovery_count, drwtim;
75         static const u8 recovery_values[] =
76                 {15, 15, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 0};
77         static const u8 drwtim_regs[4] = {DRWTIM0, DRWTIM1, DRWTIM2, DRWTIM3};
78
79         cmdprintk("program_cycle_times parameters: total=%d, active=%d\n",
80                   cycle_time, active_time);
81
82         cycle_count     = quantize_timing( cycle_time, clock_time);
83         active_count    = quantize_timing(active_time, clock_time);
84         recovery_count  = cycle_count - active_count;
85
86         /*
87          * In case we've got too long recovery phase, try to lengthen
88          * the active phase
89          */
90         if (recovery_count > 16) {
91                 active_count += recovery_count - 16;
92                 recovery_count = 16;
93         }
94         if (active_count > 16)          /* shouldn't actually happen... */
95                 active_count = 16;
96
97         cmdprintk("Final counts: total=%d, active=%d, recovery=%d\n",
98                   cycle_count, active_count, recovery_count);
99
100         /*
101          * Convert values to internal chipset representation
102          */
103         recovery_count = recovery_values[recovery_count];
104         active_count  &= 0x0f;
105
106         /* Program the active/recovery counts into the DRWTIM register */
107         drwtim = (active_count << 4) | recovery_count;
108         (void) pci_write_config_byte(dev, drwtim_regs[drive->dn], drwtim);
109         cmdprintk("Write 0x%02x to reg 0x%x\n", drwtim, drwtim_regs[drive->dn]);
110 }
111
112 /*
113  * This routine writes into the chipset registers
114  * PIO setup/active/recovery timings.
115  */
116 static void cmd64x_tune_pio(ide_drive_t *drive, const u8 pio)
117 {
118         ide_hwif_t *hwif        = HWIF(drive);
119         struct pci_dev *dev     = to_pci_dev(hwif->dev);
120         unsigned int cycle_time;
121         u8 setup_count, arttim = 0;
122
123         static const u8 setup_values[] = {0x40, 0x40, 0x40, 0x80, 0, 0xc0};
124         static const u8 arttim_regs[4] = {ARTTIM0, ARTTIM1, ARTTIM23, ARTTIM23};
125
126         cycle_time = ide_pio_cycle_time(drive, pio);
127
128         program_cycle_times(drive, cycle_time,
129                             ide_pio_timings[pio].active_time);
130
131         setup_count = quantize_timing(ide_pio_timings[pio].setup_time,
132                                       1000 / system_bus_clock());
133
134         /*
135          * The primary channel has individual address setup timing registers
136          * for each drive and the hardware selects the slowest timing itself.
137          * The secondary channel has one common register and we have to select
138          * the slowest address setup timing ourselves.
139          */
140         if (hwif->channel) {
141                 ide_drive_t *drives = hwif->drives;
142
143                 drive->drive_data = setup_count;
144                 setup_count = max(drives[0].drive_data, drives[1].drive_data);
145         }
146
147         if (setup_count > 5)            /* shouldn't actually happen... */
148                 setup_count = 5;
149         cmdprintk("Final address setup count: %d\n", setup_count);
150
151         /*
152          * Program the address setup clocks into the ARTTIM registers.
153          * Avoid clearing the secondary channel's interrupt bit.
154          */
155         (void) pci_read_config_byte (dev, arttim_regs[drive->dn], &arttim);
156         if (hwif->channel)
157                 arttim &= ~ARTTIM23_INTR_CH1;
158         arttim &= ~0xc0;
159         arttim |= setup_values[setup_count];
160         (void) pci_write_config_byte(dev, arttim_regs[drive->dn], arttim);
161         cmdprintk("Write 0x%02x to reg 0x%x\n", arttim, arttim_regs[drive->dn]);
162 }
163
164 /*
165  * Attempts to set drive's PIO mode.
166  * Special cases are 8: prefetch off, 9: prefetch on (both never worked)
167  */
168
169 static void cmd64x_set_pio_mode(ide_drive_t *drive, const u8 pio)
170 {
171         /*
172          * Filter out the prefetch control values
173          * to prevent PIO5 from being programmed
174          */
175         if (pio == 8 || pio == 9)
176                 return;
177
178         cmd64x_tune_pio(drive, pio);
179 }
180
181 static void cmd64x_set_dma_mode(ide_drive_t *drive, const u8 speed)
182 {
183         ide_hwif_t *hwif        = HWIF(drive);
184         struct pci_dev *dev     = to_pci_dev(hwif->dev);
185         u8 unit                 = drive->dn & 0x01;
186         u8 regU = 0, pciU       = hwif->channel ? UDIDETCR1 : UDIDETCR0;
187
188         if (speed >= XFER_SW_DMA_0) {
189                 (void) pci_read_config_byte(dev, pciU, &regU);
190                 regU &= ~(unit ? 0xCA : 0x35);
191         }
192
193         switch(speed) {
194         case XFER_UDMA_5:
195                 regU |= unit ? 0x0A : 0x05;
196                 break;
197         case XFER_UDMA_4:
198                 regU |= unit ? 0x4A : 0x15;
199                 break;
200         case XFER_UDMA_3:
201                 regU |= unit ? 0x8A : 0x25;
202                 break;
203         case XFER_UDMA_2:
204                 regU |= unit ? 0x42 : 0x11;
205                 break;
206         case XFER_UDMA_1:
207                 regU |= unit ? 0x82 : 0x21;
208                 break;
209         case XFER_UDMA_0:
210                 regU |= unit ? 0xC2 : 0x31;
211                 break;
212         case XFER_MW_DMA_2:
213                 program_cycle_times(drive, 120, 70);
214                 break;
215         case XFER_MW_DMA_1:
216                 program_cycle_times(drive, 150, 80);
217                 break;
218         case XFER_MW_DMA_0:
219                 program_cycle_times(drive, 480, 215);
220                 break;
221         }
222
223         if (speed >= XFER_SW_DMA_0)
224                 (void) pci_write_config_byte(dev, pciU, regU);
225 }
226
227 static int cmd648_ide_dma_end (ide_drive_t *drive)
228 {
229         ide_hwif_t *hwif        = HWIF(drive);
230         unsigned long base      = hwif->dma_base - (hwif->channel * 8);
231         int err                 = __ide_dma_end(drive);
232         u8  irq_mask            = hwif->channel ? MRDMODE_INTR_CH1 :
233                                                   MRDMODE_INTR_CH0;
234         u8  mrdmode             = inb(base + 1);
235
236         /* clear the interrupt bit */
237         outb((mrdmode & ~(MRDMODE_INTR_CH0 | MRDMODE_INTR_CH1)) | irq_mask,
238              base + 1);
239
240         return err;
241 }
242
243 static int cmd64x_ide_dma_end (ide_drive_t *drive)
244 {
245         ide_hwif_t *hwif        = HWIF(drive);
246         struct pci_dev *dev     = to_pci_dev(hwif->dev);
247         int irq_reg             = hwif->channel ? ARTTIM23 : CFR;
248         u8  irq_mask            = hwif->channel ? ARTTIM23_INTR_CH1 :
249                                                   CFR_INTR_CH0;
250         u8  irq_stat            = 0;
251         int err                 = __ide_dma_end(drive);
252
253         (void) pci_read_config_byte(dev, irq_reg, &irq_stat);
254         /* clear the interrupt bit */
255         (void) pci_write_config_byte(dev, irq_reg, irq_stat | irq_mask);
256
257         return err;
258 }
259
260 static int cmd648_ide_dma_test_irq (ide_drive_t *drive)
261 {
262         ide_hwif_t *hwif        = HWIF(drive);
263         unsigned long base      = hwif->dma_base - (hwif->channel * 8);
264         u8 irq_mask             = hwif->channel ? MRDMODE_INTR_CH1 :
265                                                   MRDMODE_INTR_CH0;
266         u8 dma_stat             = inb(hwif->dma_status);
267         u8 mrdmode              = inb(base + 1);
268
269 #ifdef DEBUG
270         printk("%s: dma_stat: 0x%02x mrdmode: 0x%02x irq_mask: 0x%02x\n",
271                drive->name, dma_stat, mrdmode, irq_mask);
272 #endif
273         if (!(mrdmode & irq_mask))
274                 return 0;
275
276         /* return 1 if INTR asserted */
277         if (dma_stat & 4)
278                 return 1;
279
280         return 0;
281 }
282
283 static int cmd64x_ide_dma_test_irq (ide_drive_t *drive)
284 {
285         ide_hwif_t *hwif        = HWIF(drive);
286         struct pci_dev *dev     = to_pci_dev(hwif->dev);
287         int irq_reg             = hwif->channel ? ARTTIM23 : CFR;
288         u8  irq_mask            = hwif->channel ? ARTTIM23_INTR_CH1 :
289                                                   CFR_INTR_CH0;
290         u8  dma_stat            = inb(hwif->dma_status);
291         u8  irq_stat            = 0;
292
293         (void) pci_read_config_byte(dev, irq_reg, &irq_stat);
294
295 #ifdef DEBUG
296         printk("%s: dma_stat: 0x%02x irq_stat: 0x%02x irq_mask: 0x%02x\n",
297                drive->name, dma_stat, irq_stat, irq_mask);
298 #endif
299         if (!(irq_stat & irq_mask))
300                 return 0;
301
302         /* return 1 if INTR asserted */
303         if (dma_stat & 4)
304                 return 1;
305
306         return 0;
307 }
308
309 /*
310  * ASUS P55T2P4D with CMD646 chipset revision 0x01 requires the old
311  * event order for DMA transfers.
312  */
313
314 static int cmd646_1_ide_dma_end (ide_drive_t *drive)
315 {
316         ide_hwif_t *hwif = HWIF(drive);
317         u8 dma_stat = 0, dma_cmd = 0;
318
319         drive->waiting_for_dma = 0;
320         /* get DMA status */
321         dma_stat = inb(hwif->dma_status);
322         /* read DMA command state */
323         dma_cmd = inb(hwif->dma_command);
324         /* stop DMA */
325         outb(dma_cmd & ~1, hwif->dma_command);
326         /* clear the INTR & ERROR bits */
327         outb(dma_stat | 6, hwif->dma_status);
328         /* and free any DMA resources */
329         ide_destroy_dmatable(drive);
330         /* verify good DMA status */
331         return (dma_stat & 7) != 4;
332 }
333
334 static unsigned int __devinit init_chipset_cmd64x(struct pci_dev *dev, const char *name)
335 {
336         u8 mrdmode = 0;
337
338         if (dev->device == PCI_DEVICE_ID_CMD_646) {
339
340                 switch (dev->revision) {
341                 case 0x07:
342                 case 0x05:
343                         printk("%s: UltraDMA capable\n", name);
344                         break;
345                 case 0x03:
346                 default:
347                         printk("%s: MultiWord DMA force limited\n", name);
348                         break;
349                 case 0x01:
350                         printk("%s: MultiWord DMA limited, "
351                                "IRQ workaround enabled\n", name);
352                         break;
353                 }
354         }
355
356         /* Set a good latency timer and cache line size value. */
357         (void) pci_write_config_byte(dev, PCI_LATENCY_TIMER, 64);
358         /* FIXME: pci_set_master() to ensure a good latency timer value */
359
360         /*
361          * Enable interrupts, select MEMORY READ LINE for reads.
362          *
363          * NOTE: although not mentioned in the PCI0646U specs,
364          * bits 0-1 are write only and won't be read back as
365          * set or not -- PCI0646U2 specs clarify this point.
366          */
367         (void) pci_read_config_byte (dev, MRDMODE, &mrdmode);
368         mrdmode &= ~0x30;
369         (void) pci_write_config_byte(dev, MRDMODE, (mrdmode | 0x02));
370
371         return 0;
372 }
373
374 static u8 __devinit ata66_cmd64x(ide_hwif_t *hwif)
375 {
376         struct pci_dev  *dev    = to_pci_dev(hwif->dev);
377         u8 bmidecsr = 0, mask   = hwif->channel ? 0x02 : 0x01;
378
379         switch (dev->device) {
380         case PCI_DEVICE_ID_CMD_648:
381         case PCI_DEVICE_ID_CMD_649:
382                 pci_read_config_byte(dev, BMIDECSR, &bmidecsr);
383                 return (bmidecsr & mask) ? ATA_CBL_PATA80 : ATA_CBL_PATA40;
384         default:
385                 return ATA_CBL_PATA40;
386         }
387 }
388
389 static void __devinit init_hwif_cmd64x(ide_hwif_t *hwif)
390 {
391         struct pci_dev *dev = to_pci_dev(hwif->dev);
392
393         hwif->set_pio_mode = &cmd64x_set_pio_mode;
394         hwif->set_dma_mode = &cmd64x_set_dma_mode;
395
396         hwif->cable_detect = ata66_cmd64x;
397
398         if (!hwif->dma_base)
399                 return;
400
401         /*
402          * UltraDMA only supported on PCI646U and PCI646U2, which
403          * correspond to revisions 0x03, 0x05 and 0x07 respectively.
404          * Actually, although the CMD tech support people won't
405          * tell me the details, the 0x03 revision cannot support
406          * UDMA correctly without hardware modifications, and even
407          * then it only works with Quantum disks due to some
408          * hold time assumptions in the 646U part which are fixed
409          * in the 646U2.
410          *
411          * So we only do UltraDMA on revision 0x05 and 0x07 chipsets.
412          */
413         if (dev->device == PCI_DEVICE_ID_CMD_646 && dev->revision < 5)
414                 hwif->ultra_mask = 0x00;
415
416         switch (dev->device) {
417         case PCI_DEVICE_ID_CMD_648:
418         case PCI_DEVICE_ID_CMD_649:
419         alt_irq_bits:
420                 hwif->ide_dma_end       = &cmd648_ide_dma_end;
421                 hwif->ide_dma_test_irq  = &cmd648_ide_dma_test_irq;
422                 break;
423         case PCI_DEVICE_ID_CMD_646:
424                 if (dev->revision == 0x01) {
425                         hwif->ide_dma_end = &cmd646_1_ide_dma_end;
426                         break;
427                 } else if (dev->revision >= 0x03)
428                         goto alt_irq_bits;
429                 /* fall thru */
430         default:
431                 hwif->ide_dma_end       = &cmd64x_ide_dma_end;
432                 hwif->ide_dma_test_irq  = &cmd64x_ide_dma_test_irq;
433                 break;
434         }
435 }
436
437 static const struct ide_port_info cmd64x_chipsets[] __devinitdata = {
438         {       /* 0 */
439                 .name           = "CMD643",
440                 .init_chipset   = init_chipset_cmd64x,
441                 .init_hwif      = init_hwif_cmd64x,
442                 .enablebits     = {{0x00,0x00,0x00}, {0x51,0x08,0x08}},
443                 .host_flags     = IDE_HFLAG_CLEAR_SIMPLEX |
444                                   IDE_HFLAG_ABUSE_PREFETCH |
445                                   IDE_HFLAG_BOOTABLE,
446                 .pio_mask       = ATA_PIO5,
447                 .mwdma_mask     = ATA_MWDMA2,
448                 .udma_mask      = 0x00, /* no udma */
449         },{     /* 1 */
450                 .name           = "CMD646",
451                 .init_chipset   = init_chipset_cmd64x,
452                 .init_hwif      = init_hwif_cmd64x,
453                 .enablebits     = {{0x51,0x04,0x04}, {0x51,0x08,0x08}},
454                 .chipset        = ide_cmd646,
455                 .host_flags     = IDE_HFLAG_ABUSE_PREFETCH | IDE_HFLAG_BOOTABLE,
456                 .pio_mask       = ATA_PIO5,
457                 .mwdma_mask     = ATA_MWDMA2,
458                 .udma_mask      = ATA_UDMA2,
459         },{     /* 2 */
460                 .name           = "CMD648",
461                 .init_chipset   = init_chipset_cmd64x,
462                 .init_hwif      = init_hwif_cmd64x,
463                 .enablebits     = {{0x51,0x04,0x04}, {0x51,0x08,0x08}},
464                 .host_flags     = IDE_HFLAG_ABUSE_PREFETCH | IDE_HFLAG_BOOTABLE,
465                 .pio_mask       = ATA_PIO5,
466                 .mwdma_mask     = ATA_MWDMA2,
467                 .udma_mask      = ATA_UDMA4,
468         },{     /* 3 */
469                 .name           = "CMD649",
470                 .init_chipset   = init_chipset_cmd64x,
471                 .init_hwif      = init_hwif_cmd64x,
472                 .enablebits     = {{0x51,0x04,0x04}, {0x51,0x08,0x08}},
473                 .host_flags     = IDE_HFLAG_ABUSE_PREFETCH | IDE_HFLAG_BOOTABLE,
474                 .pio_mask       = ATA_PIO5,
475                 .mwdma_mask     = ATA_MWDMA2,
476                 .udma_mask      = ATA_UDMA5,
477         }
478 };
479
480 static int __devinit cmd64x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
481 {
482         struct ide_port_info d;
483         u8 idx = id->driver_data;
484
485         d = cmd64x_chipsets[idx];
486
487         /*
488          * The original PCI0646 didn't have the primary channel enable bit,
489          * it appeared starting with PCI0646U (i.e. revision ID 3).
490          */
491         if (idx == 1 && dev->revision < 3)
492                 d.enablebits[0].reg = 0;
493
494         return ide_setup_pci_device(dev, &d);
495 }
496
497 static const struct pci_device_id cmd64x_pci_tbl[] = {
498         { PCI_VDEVICE(CMD, PCI_DEVICE_ID_CMD_643), 0 },
499         { PCI_VDEVICE(CMD, PCI_DEVICE_ID_CMD_646), 1 },
500         { PCI_VDEVICE(CMD, PCI_DEVICE_ID_CMD_648), 2 },
501         { PCI_VDEVICE(CMD, PCI_DEVICE_ID_CMD_649), 3 },
502         { 0, },
503 };
504 MODULE_DEVICE_TABLE(pci, cmd64x_pci_tbl);
505
506 static struct pci_driver driver = {
507         .name           = "CMD64x_IDE",
508         .id_table       = cmd64x_pci_tbl,
509         .probe          = cmd64x_init_one,
510 };
511
512 static int __init cmd64x_ide_init(void)
513 {
514         return ide_pci_register_driver(&driver);
515 }
516
517 module_init(cmd64x_ide_init);
518
519 MODULE_AUTHOR("Eddie Dost, David Miller, Andre Hedrick");
520 MODULE_DESCRIPTION("PCI driver module for CMD64x IDE");
521 MODULE_LICENSE("GPL");