drivers/i2c/busses/i2c-imx.c

   1 // SPDX-License-Identifier: GPL-2.0+
   2 /*
   3  *      Copyright (C) 2002 Motorola GSG-China
   4  *
   5  * Author:
   6  *      Darius Augulis, Teltonika Inc.
   7  *
   8  * Desc.:
   9  *      Implementation of I2C Adapter/Algorithm Driver
  10  *      for I2C Bus integrated in Freescale i.MX/MXC processors
  11  *
  12  *      Derived from Motorola GSG China I2C example driver
  13  *
  14  *      Copyright (C) 2005 Torsten Koschorrek <koschorrek at synertronixx.de
  15  *      Copyright (C) 2005 Matthias Blaschke <blaschke at synertronixx.de
  16  *      Copyright (C) 2007 RightHand Technologies, Inc.
  17  *      Copyright (C) 2008 Darius Augulis <darius.augulis at teltonika.lt>
  18  *
  19  *      Copyright 2013 Freescale Semiconductor, Inc.
  20  *
  21  */
  22
  23 #include <linux/clk.h>
  24 #include <linux/completion.h>
  25 #include <linux/delay.h>
  26 #include <linux/dma-mapping.h>
  27 #include <linux/dmaengine.h>
  28 #include <linux/dmapool.h>
  29 #include <linux/err.h>
  30 #include <linux/errno.h>
  31 #include <linux/gpio/consumer.h>
  32 #include <linux/i2c.h>
  33 #include <linux/init.h>
  34 #include <linux/interrupt.h>
  35 #include <linux/io.h>
  36 #include <linux/kernel.h>
  37 #include <linux/module.h>
  38 #include <linux/of.h>
  39 #include <linux/of_device.h>
  40 #include <linux/of_dma.h>
  41 #include <linux/pinctrl/consumer.h>
  42 #include <linux/platform_data/i2c-imx.h>
  43 #include <linux/platform_device.h>
  44 #include <linux/pm_runtime.h>
  45 #include <linux/sched.h>
  46 #include <linux/slab.h>
  47
  48 /* This will be the driver name the kernel reports */
  49 #define DRIVER_NAME "imx-i2c"
  50
  51 /* Default value */
  52 #define IMX_I2C_BIT_RATE        100000  /* 100kHz */
  53
  54 /*
  55  * Enable DMA if transfer byte size is bigger than this threshold.
  56  * As the hardware request, it must bigger than 4 bytes.\
  57  * I have set '16' here, maybe it's not the best but I think it's
  58  * the appropriate.
  59  */
  60 #define DMA_THRESHOLD   16
  61 #define DMA_TIMEOUT     1000
  62
  63 /* IMX I2C registers:
  64  * the I2C register offset is different between SoCs,
  65  * to provid support for all these chips, split the
  66  * register offset into a fixed base address and a
  67  * variable shift value, then the full register offset
  68  * will be calculated by
  69  * reg_off = ( reg_base_addr << reg_shift)
  70  */
  71 #define IMX_I2C_IADR    0x00    /* i2c slave address */
  72 #define IMX_I2C_IFDR    0x01    /* i2c frequency divider */
  73 #define IMX_I2C_I2CR    0x02    /* i2c control */
  74 #define IMX_I2C_I2SR    0x03    /* i2c status */
  75 #define IMX_I2C_I2DR    0x04    /* i2c transfer data */
  76
  77 #define IMX_I2C_REGSHIFT        2
  78 #define VF610_I2C_REGSHIFT      0
  79
  80 /* Bits of IMX I2C registers */
  81 #define I2SR_RXAK       0x01
  82 #define I2SR_IIF        0x02
  83 #define I2SR_SRW        0x04
  84 #define I2SR_IAL        0x10
  85 #define I2SR_IBB        0x20
  86 #define I2SR_IAAS       0x40
  87 #define I2SR_ICF        0x80
  88 #define I2CR_DMAEN      0x02
  89 #define I2CR_RSTA       0x04
  90 #define I2CR_TXAK       0x08
  91 #define I2CR_MTX        0x10
  92 #define I2CR_MSTA       0x20
  93 #define I2CR_IIEN       0x40
  94 #define I2CR_IEN        0x80
  95
  96 /* register bits different operating codes definition:
  97  * 1) I2SR: Interrupt flags clear operation differ between SoCs:
  98  * - write zero to clear(w0c) INT flag on i.MX,
  99  * - but write one to clear(w1c) INT flag on Vybrid.
 100  * 2) I2CR: I2C module enable operation also differ between SoCs:
 101  * - set I2CR_IEN bit enable the module on i.MX,
 102  * - but clear I2CR_IEN bit enable the module on Vybrid.
 103  */
 104 #define I2SR_CLR_OPCODE_W0C     0x0
 105 #define I2SR_CLR_OPCODE_W1C     (I2SR_IAL | I2SR_IIF)
 106 #define I2CR_IEN_OPCODE_0       0x0
 107 #define I2CR_IEN_OPCODE_1       I2CR_IEN
 108
 109 #define I2C_PM_TIMEOUT          10 /* ms */
 110
 111 /*
 112  * sorted list of clock divider, register value pairs
 113  * taken from table 26-5, p.26-9, Freescale i.MX
 114  * Integrated Portable System Processor Reference Manual
 115  * Document Number: MC9328MXLRM, Rev. 5.1, 06/2007
 116  *
 117  * Duplicated divider values removed from list
 118  */
 119 struct imx_i2c_clk_pair {
 120         u16     div;
 121         u16     val;
 122 };
 123
 124 static struct imx_i2c_clk_pair imx_i2c_clk_div[] = {
 125         { 22,   0x20 }, { 24,   0x21 }, { 26,   0x22 }, { 28,   0x23 },
 126         { 30,   0x00 }, { 32,   0x24 }, { 36,   0x25 }, { 40,   0x26 },
 127         { 42,   0x03 }, { 44,   0x27 }, { 48,   0x28 }, { 52,   0x05 },
 128         { 56,   0x29 }, { 60,   0x06 }, { 64,   0x2A }, { 72,   0x2B },
 129         { 80,   0x2C }, { 88,   0x09 }, { 96,   0x2D }, { 104,  0x0A },
 130         { 112,  0x2E }, { 128,  0x2F }, { 144,  0x0C }, { 160,  0x30 },
 131         { 192,  0x31 }, { 224,  0x32 }, { 240,  0x0F }, { 256,  0x33 },
 132         { 288,  0x10 }, { 320,  0x34 }, { 384,  0x35 }, { 448,  0x36 },
 133         { 480,  0x13 }, { 512,  0x37 }, { 576,  0x14 }, { 640,  0x38 },
 134         { 768,  0x39 }, { 896,  0x3A }, { 960,  0x17 }, { 1024, 0x3B },
 135         { 1152, 0x18 }, { 1280, 0x3C }, { 1536, 0x3D }, { 1792, 0x3E },
 136         { 1920, 0x1B }, { 2048, 0x3F }, { 2304, 0x1C }, { 2560, 0x1D },
 137         { 3072, 0x1E }, { 3840, 0x1F }
 138 };
 139
 140 /* Vybrid VF610 clock divider, register value pairs */
 141 static struct imx_i2c_clk_pair vf610_i2c_clk_div[] = {
 142         { 20,   0x00 }, { 22,   0x01 }, { 24,   0x02 }, { 26,   0x03 },
 143         { 28,   0x04 }, { 30,   0x05 }, { 32,   0x09 }, { 34,   0x06 },
 144         { 36,   0x0A }, { 40,   0x07 }, { 44,   0x0C }, { 48,   0x0D },
 145         { 52,   0x43 }, { 56,   0x0E }, { 60,   0x45 }, { 64,   0x12 },
 146         { 68,   0x0F }, { 72,   0x13 }, { 80,   0x14 }, { 88,   0x15 },
 147         { 96,   0x19 }, { 104,  0x16 }, { 112,  0x1A }, { 128,  0x17 },
 148         { 136,  0x4F }, { 144,  0x1C }, { 160,  0x1D }, { 176,  0x55 },
 149         { 192,  0x1E }, { 208,  0x56 }, { 224,  0x22 }, { 228,  0x24 },
 150         { 240,  0x1F }, { 256,  0x23 }, { 288,  0x5C }, { 320,  0x25 },
 151         { 384,  0x26 }, { 448,  0x2A }, { 480,  0x27 }, { 512,  0x2B },
 152         { 576,  0x2C }, { 640,  0x2D }, { 768,  0x31 }, { 896,  0x32 },
 153         { 960,  0x2F }, { 1024, 0x33 }, { 1152, 0x34 }, { 1280, 0x35 },
 154         { 1536, 0x36 }, { 1792, 0x3A }, { 1920, 0x37 }, { 2048, 0x3B },
 155         { 2304, 0x3C }, { 2560, 0x3D }, { 3072, 0x3E }, { 3584, 0x7A },
 156         { 3840, 0x3F }, { 4096, 0x7B }, { 5120, 0x7D }, { 6144, 0x7E },
 157 };
 158
 159 enum imx_i2c_type {
 160         IMX1_I2C,
 161         IMX21_I2C,
 162         VF610_I2C,
 163 };
 164
 165 struct imx_i2c_hwdata {
 166         enum imx_i2c_type       devtype;
 167         unsigned                regshift;
 168         struct imx_i2c_clk_pair *clk_div;
 169         unsigned                ndivs;
 170         unsigned                i2sr_clr_opcode;
 171         unsigned                i2cr_ien_opcode;
 172 };
 173
 174 struct imx_i2c_dma {
 175         struct dma_chan         *chan_tx;
 176         struct dma_chan         *chan_rx;
 177         struct dma_chan         *chan_using;
 178         struct completion       cmd_complete;
 179         dma_addr_t              dma_buf;
 180         unsigned int            dma_len;
 181         enum dma_transfer_direction dma_transfer_dir;
 182         enum dma_data_direction dma_data_dir;
 183 };
 184
 185 struct imx_i2c_struct {
 186         struct i2c_adapter      adapter;
 187         struct clk              *clk;
 188         struct notifier_block   clk_change_nb;
 189         void __iomem            *base;
 190         wait_queue_head_t       queue;
 191         unsigned long           i2csr;
 192         unsigned int            disable_delay;
 193         int                     stopped;
 194         unsigned int            ifdr; /* IMX_I2C_IFDR */
 195         unsigned int            cur_clk;
 196         unsigned int            bitrate;
 197         const struct imx_i2c_hwdata     *hwdata;
 198         struct i2c_bus_recovery_info rinfo;
 199
 200         struct pinctrl *pinctrl;
 201         struct pinctrl_state *pinctrl_pins_default;
 202         struct pinctrl_state *pinctrl_pins_gpio;
 203
 204         struct imx_i2c_dma      *dma;
 205 };
 206
 207 static const struct imx_i2c_hwdata imx1_i2c_hwdata = {
 208         .devtype                = IMX1_I2C,
 209         .regshift               = IMX_I2C_REGSHIFT,
 210         .clk_div                = imx_i2c_clk_div,
 211         .ndivs                  = ARRAY_SIZE(imx_i2c_clk_div),
 212         .i2sr_clr_opcode        = I2SR_CLR_OPCODE_W0C,
 213         .i2cr_ien_opcode        = I2CR_IEN_OPCODE_1,
 214
 215 };
 216
 217 static const struct imx_i2c_hwdata imx21_i2c_hwdata = {
 218         .devtype                = IMX21_I2C,
 219         .regshift               = IMX_I2C_REGSHIFT,
 220         .clk_div                = imx_i2c_clk_div,
 221         .ndivs                  = ARRAY_SIZE(imx_i2c_clk_div),
 222         .i2sr_clr_opcode        = I2SR_CLR_OPCODE_W0C,
 223         .i2cr_ien_opcode        = I2CR_IEN_OPCODE_1,
 224
 225 };
 226
 227 static struct imx_i2c_hwdata vf610_i2c_hwdata = {
 228         .devtype                = VF610_I2C,
 229         .regshift               = VF610_I2C_REGSHIFT,
 230         .clk_div                = vf610_i2c_clk_div,
 231         .ndivs                  = ARRAY_SIZE(vf610_i2c_clk_div),
 232         .i2sr_clr_opcode        = I2SR_CLR_OPCODE_W1C,
 233         .i2cr_ien_opcode        = I2CR_IEN_OPCODE_0,
 234
 235 };
 236
 237 static const struct platform_device_id imx_i2c_devtype[] = {
 238         {
 239                 .name = "imx1-i2c",
 240                 .driver_data = (kernel_ulong_t)&imx1_i2c_hwdata,
 241         }, {
 242                 .name = "imx21-i2c",
 243                 .driver_data = (kernel_ulong_t)&imx21_i2c_hwdata,
 244         }, {
 245                 /* sentinel */
 246         }
 247 };
 248 MODULE_DEVICE_TABLE(platform, imx_i2c_devtype);
 249
 250 static const struct of_device_id i2c_imx_dt_ids[] = {
 251         { .compatible = "fsl,imx1-i2c", .data = &imx1_i2c_hwdata, },
 252         { .compatible = "fsl,imx21-i2c", .data = &imx21_i2c_hwdata, },
 253         { .compatible = "fsl,vf610-i2c", .data = &vf610_i2c_hwdata, },
 254         { /* sentinel */ }
 255 };
 256 MODULE_DEVICE_TABLE(of, i2c_imx_dt_ids);
 257
 258 static inline int is_imx1_i2c(struct imx_i2c_struct *i2c_imx)
 259 {
 260         return i2c_imx->hwdata->devtype == IMX1_I2C;
 261 }
 262
 263 static inline void imx_i2c_write_reg(unsigned int val,
 264                 struct imx_i2c_struct *i2c_imx, unsigned int reg)
 265 {
 266         writeb(val, i2c_imx->base + (reg << i2c_imx->hwdata->regshift));
 267 }
 268
 269 static inline unsigned char imx_i2c_read_reg(struct imx_i2c_struct *i2c_imx,
 270                 unsigned int reg)
 271 {
 272         return readb(i2c_imx->base + (reg << i2c_imx->hwdata->regshift));
 273 }
 274
 275 /* Functions for DMA support */
 276 static void i2c_imx_dma_request(struct imx_i2c_struct *i2c_imx,
 277                                                 dma_addr_t phy_addr)
 278 {
 279         struct imx_i2c_dma *dma;
 280         struct dma_slave_config dma_sconfig;
 281         struct device *dev = &i2c_imx->adapter.dev;
 282         int ret;
 283
 284         dma = devm_kzalloc(dev, sizeof(*dma), GFP_KERNEL);
 285         if (!dma)
 286                 return;
 287
 288         dma->chan_tx = dma_request_slave_channel(dev, "tx");
 289         if (!dma->chan_tx) {
 290                 dev_dbg(dev, "can't request DMA tx channel\n");
 291                 goto fail_al;
 292         }
 293
 294         dma_sconfig.dst_addr = phy_addr +
 295                                 (IMX_I2C_I2DR << i2c_imx->hwdata->regshift);
 296         dma_sconfig.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
 297         dma_sconfig.dst_maxburst = 1;
 298         dma_sconfig.direction = DMA_MEM_TO_DEV;
 299         ret = dmaengine_slave_config(dma->chan_tx, &dma_sconfig);
 300         if (ret < 0) {
 301                 dev_dbg(dev, "can't configure tx channel\n");
 302                 goto fail_tx;
 303         }
 304
 305         dma->chan_rx = dma_request_slave_channel(dev, "rx");
 306         if (!dma->chan_rx) {
 307                 dev_dbg(dev, "can't request DMA rx channel\n");
 308                 goto fail_tx;
 309         }
 310
 311         dma_sconfig.src_addr = phy_addr +
 312                                 (IMX_I2C_I2DR << i2c_imx->hwdata->regshift);
 313         dma_sconfig.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
 314         dma_sconfig.src_maxburst = 1;
 315         dma_sconfig.direction = DMA_DEV_TO_MEM;
 316         ret = dmaengine_slave_config(dma->chan_rx, &dma_sconfig);
 317         if (ret < 0) {
 318                 dev_dbg(dev, "can't configure rx channel\n");
 319                 goto fail_rx;
 320         }
 321
 322         i2c_imx->dma = dma;
 323         init_completion(&dma->cmd_complete);
 324         dev_info(dev, "using %s (tx) and %s (rx) for DMA transfers\n",
 325                 dma_chan_name(dma->chan_tx), dma_chan_name(dma->chan_rx));
 326
 327         return;
 328
 329 fail_rx:
 330         dma_release_channel(dma->chan_rx);
 331 fail_tx:
 332         dma_release_channel(dma->chan_tx);
 333 fail_al:
 334         devm_kfree(dev, dma);
 335         dev_info(dev, "can't use DMA, using PIO instead.\n");
 336 }
 337
 338 static void i2c_imx_dma_callback(void *arg)
 339 {
 340         struct imx_i2c_struct *i2c_imx = (struct imx_i2c_struct *)arg;
 341         struct imx_i2c_dma *dma = i2c_imx->dma;
 342
 343         dma_unmap_single(dma->chan_using->device->dev, dma->dma_buf,
 344                         dma->dma_len, dma->dma_data_dir);
 345         complete(&dma->cmd_complete);
 346 }
 347
 348 static int i2c_imx_dma_xfer(struct imx_i2c_struct *i2c_imx,
 349                                         struct i2c_msg *msgs)
 350 {
 351         struct imx_i2c_dma *dma = i2c_imx->dma;
 352         struct dma_async_tx_descriptor *txdesc;
 353         struct device *dev = &i2c_imx->adapter.dev;
 354         struct device *chan_dev = dma->chan_using->device->dev;
 355
 356         dma->dma_buf = dma_map_single(chan_dev, msgs->buf,
 357                                         dma->dma_len, dma->dma_data_dir);
 358         if (dma_mapping_error(chan_dev, dma->dma_buf)) {
 359                 dev_err(dev, "DMA mapping failed\n");
 360                 goto err_map;
 361         }
 362
 363         txdesc = dmaengine_prep_slave_single(dma->chan_using, dma->dma_buf,
 364                                         dma->dma_len, dma->dma_transfer_dir,
 365                                         DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
 366         if (!txdesc) {
 367                 dev_err(dev, "Not able to get desc for DMA xfer\n");
 368                 goto err_desc;
 369         }
 370
 371         reinit_completion(&dma->cmd_complete);
 372         txdesc->callback = i2c_imx_dma_callback;
 373         txdesc->callback_param = i2c_imx;
 374         if (dma_submit_error(dmaengine_submit(txdesc))) {
 375                 dev_err(dev, "DMA submit failed\n");
 376                 goto err_submit;
 377         }
 378
 379         dma_async_issue_pending(dma->chan_using);
 380         return 0;
 381
 382 err_submit:
 383         dmaengine_terminate_all(dma->chan_using);
 384 err_desc:
 385         dma_unmap_single(chan_dev, dma->dma_buf,
 386                         dma->dma_len, dma->dma_data_dir);
 387 err_map:
 388         return -EINVAL;
 389 }
 390
 391 static void i2c_imx_dma_free(struct imx_i2c_struct *i2c_imx)
 392 {
 393         struct imx_i2c_dma *dma = i2c_imx->dma;
 394
 395         dma->dma_buf = 0;
 396         dma->dma_len = 0;
 397
 398         dma_release_channel(dma->chan_tx);
 399         dma->chan_tx = NULL;
 400
 401         dma_release_channel(dma->chan_rx);
 402         dma->chan_rx = NULL;
 403
 404         dma->chan_using = NULL;
 405 }
 406
 407 static int i2c_imx_bus_busy(struct imx_i2c_struct *i2c_imx, int for_busy)
 408 {
 409         unsigned long orig_jiffies = jiffies;
 410         unsigned int temp;
 411
 412         dev_dbg(&i2c_imx->adapter.dev, "<%s>\n", __func__);
 413
 414         while (1) {
 415                 temp = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2SR);
 416
 417                 /* check for arbitration lost */
 418                 if (temp & I2SR_IAL) {
 419                         temp &= ~I2SR_IAL;
 420                         imx_i2c_write_reg(temp, i2c_imx, IMX_I2C_I2SR);
 421                         return -EAGAIN;
 422                 }
 423
 424                 if (for_busy && (temp & I2SR_IBB))
 425                         break;
 426                 if (!for_busy && !(temp & I2SR_IBB))
 427                         break;
 428                 if (time_after(jiffies, orig_jiffies + msecs_to_jiffies(500))) {
 429                         dev_dbg(&i2c_imx->adapter.dev,
 430                                 "<%s> I2C bus is busy\n", __func__);
 431                         return -ETIMEDOUT;
 432                 }
 433                 schedule();
 434         }
 435
 436         return 0;
 437 }
 438
 439 static int i2c_imx_trx_complete(struct imx_i2c_struct *i2c_imx)
 440 {
 441         wait_event_timeout(i2c_imx->queue, i2c_imx->i2csr & I2SR_IIF, HZ / 10);
 442
 443         if (unlikely(!(i2c_imx->i2csr & I2SR_IIF))) {
 444                 dev_dbg(&i2c_imx->adapter.dev, "<%s> Timeout\n", __func__);
 445                 return -ETIMEDOUT;
 446         }
 447         dev_dbg(&i2c_imx->adapter.dev, "<%s> TRX complete\n", __func__);
 448         i2c_imx->i2csr = 0;
 449         return 0;
 450 }
 451
 452 static int i2c_imx_acked(struct imx_i2c_struct *i2c_imx)
 453 {
 454         if (imx_i2c_read_reg(i2c_imx, IMX_I2C_I2SR) & I2SR_RXAK) {
 455                 dev_dbg(&i2c_imx->adapter.dev, "<%s> No ACK\n", __func__);
 456                 return -ENXIO;  /* No ACK */
 457         }
 458
 459         dev_dbg(&i2c_imx->adapter.dev, "<%s> ACK received\n", __func__);
 460         return 0;
 461 }
 462
 463 static void i2c_imx_set_clk(struct imx_i2c_struct *i2c_imx,
 464                             unsigned int i2c_clk_rate)
 465 {
 466         struct imx_i2c_clk_pair *i2c_clk_div = i2c_imx->hwdata->clk_div;
 467         unsigned int div;
 468         int i;
 469
 470         /* Divider value calculation */
 471         if (i2c_imx->cur_clk == i2c_clk_rate)
 472                 return;
 473
 474         i2c_imx->cur_clk = i2c_clk_rate;
 475
 476         div = (i2c_clk_rate + i2c_imx->bitrate - 1) / i2c_imx->bitrate;
 477         if (div < i2c_clk_div[0].div)
 478                 i = 0;
 479         else if (div > i2c_clk_div[i2c_imx->hwdata->ndivs - 1].div)
 480                 i = i2c_imx->hwdata->ndivs - 1;
 481         else
 482                 for (i = 0; i2c_clk_div[i].div < div; i++)
 483                         ;
 484
 485         /* Store divider value */
 486         i2c_imx->ifdr = i2c_clk_div[i].val;
 487
 488         /*
 489          * There dummy delay is calculated.
 490          * It should be about one I2C clock period long.
 491          * This delay is used in I2C bus disable function
 492          * to fix chip hardware bug.
 493          */
 494         i2c_imx->disable_delay = (500000U * i2c_clk_div[i].div
 495                 + (i2c_clk_rate / 2) - 1) / (i2c_clk_rate / 2);
 496
 497 #ifdef CONFIG_I2C_DEBUG_BUS
 498         dev_dbg(&i2c_imx->adapter.dev, "I2C_CLK=%d, REQ DIV=%d\n",
 499                 i2c_clk_rate, div);
 500         dev_dbg(&i2c_imx->adapter.dev, "IFDR[IC]=0x%x, REAL DIV=%d\n",
 501                 i2c_clk_div[i].val, i2c_clk_div[i].div);
 502 #endif
 503 }
 504
 505 static int i2c_imx_clk_notifier_call(struct notifier_block *nb,
 506                                      unsigned long action, void *data)
 507 {
 508         struct clk_notifier_data *ndata = data;
 509         struct imx_i2c_struct *i2c_imx = container_of(&ndata->clk,
 510                                                       struct imx_i2c_struct,
 511                                                       clk);
 512
 513         if (action & POST_RATE_CHANGE)
 514                 i2c_imx_set_clk(i2c_imx, ndata->new_rate);
 515
 516         return NOTIFY_OK;
 517 }
 518
 519 static int i2c_imx_start(struct imx_i2c_struct *i2c_imx)
 520 {
 521         unsigned int temp = 0;
 522         int result;
 523
 524         dev_dbg(&i2c_imx->adapter.dev, "<%s>\n", __func__);
 525
 526         imx_i2c_write_reg(i2c_imx->ifdr, i2c_imx, IMX_I2C_IFDR);
 527         /* Enable I2C controller */
 528         imx_i2c_write_reg(i2c_imx->hwdata->i2sr_clr_opcode, i2c_imx, IMX_I2C_I2SR);
 529         imx_i2c_write_reg(i2c_imx->hwdata->i2cr_ien_opcode, i2c_imx, IMX_I2C_I2CR);
 530
 531         /* Wait controller to be stable */
 532         usleep_range(50, 150);
 533
 534         /* Start I2C transaction */
 535         temp = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2CR);
 536         temp |= I2CR_MSTA;
 537         imx_i2c_write_reg(temp, i2c_imx, IMX_I2C_I2CR);
 538         result = i2c_imx_bus_busy(i2c_imx, 1);
 539         if (result)
 540                 return result;
 541         i2c_imx->stopped = 0;
 542
 543         temp |= I2CR_IIEN | I2CR_MTX | I2CR_TXAK;
 544         temp &= ~I2CR_DMAEN;
 545         imx_i2c_write_reg(temp, i2c_imx, IMX_I2C_I2CR);
 546         return result;
 547 }
 548
 549 static void i2c_imx_stop(struct imx_i2c_struct *i2c_imx)
 550 {
 551         unsigned int temp = 0;
 552
 553         if (!i2c_imx->stopped) {
 554                 /* Stop I2C transaction */
 555                 dev_dbg(&i2c_imx->adapter.dev, "<%s>\n", __func__);
 556                 temp = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2CR);
 557                 temp &= ~(I2CR_MSTA | I2CR_MTX);
 558                 if (i2c_imx->dma)
 559                         temp &= ~I2CR_DMAEN;
 560                 imx_i2c_write_reg(temp, i2c_imx, IMX_I2C_I2CR);
 561         }
 562         if (is_imx1_i2c(i2c_imx)) {
 563                 /*
 564                  * This delay caused by an i.MXL hardware bug.
 565                  * If no (or too short) delay, no "STOP" bit will be generated.
 566                  */
 567                 udelay(i2c_imx->disable_delay);
 568         }
 569
 570         if (!i2c_imx->stopped) {
 571                 i2c_imx_bus_busy(i2c_imx, 0);
 572                 i2c_imx->stopped = 1;
 573         }
 574
 575         /* Disable I2C controller */
 576         temp = i2c_imx->hwdata->i2cr_ien_opcode ^ I2CR_IEN,
 577         imx_i2c_write_reg(temp, i2c_imx, IMX_I2C_I2CR);
 578 }
 579
 580 static irqreturn_t i2c_imx_isr(int irq, void *dev_id)
 581 {
 582         struct imx_i2c_struct *i2c_imx = dev_id;
 583         unsigned int temp;
 584
 585         temp = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2SR);
 586         if (temp & I2SR_IIF) {
 587                 /* save status register */
 588                 i2c_imx->i2csr = temp;
 589                 temp &= ~I2SR_IIF;
 590                 temp |= (i2c_imx->hwdata->i2sr_clr_opcode & I2SR_IIF);
 591                 imx_i2c_write_reg(temp, i2c_imx, IMX_I2C_I2SR);
 592                 wake_up(&i2c_imx->queue);
 593                 return IRQ_HANDLED;
 594         }
 595
 596         return IRQ_NONE;
 597 }
 598
 599 static int i2c_imx_dma_write(struct imx_i2c_struct *i2c_imx,
 600                                         struct i2c_msg *msgs)
 601 {
 602         int result;
 603         unsigned long time_left;
 604         unsigned int temp = 0;
 605         unsigned long orig_jiffies = jiffies;
 606         struct imx_i2c_dma *dma = i2c_imx->dma;
 607         struct device *dev = &i2c_imx->adapter.dev;
 608
 609         dma->chan_using = dma->chan_tx;
 610         dma->dma_transfer_dir = DMA_MEM_TO_DEV;
 611         dma->dma_data_dir = DMA_TO_DEVICE;
 612         dma->dma_len = msgs->len - 1;
 613         result = i2c_imx_dma_xfer(i2c_imx, msgs);
 614         if (result)
 615                 return result;
 616
 617         temp = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2CR);
 618         temp |= I2CR_DMAEN;
 619         imx_i2c_write_reg(temp, i2c_imx, IMX_I2C_I2CR);
 620
 621         /*
 622          * Write slave address.
 623          * The first byte must be transmitted by the CPU.
 624          */
 625         imx_i2c_write_reg(i2c_8bit_addr_from_msg(msgs), i2c_imx, IMX_I2C_I2DR);
 626         time_left = wait_for_completion_timeout(
 627                                 &i2c_imx->dma->cmd_complete,
 628                                 msecs_to_jiffies(DMA_TIMEOUT));
 629         if (time_left == 0) {
 630                 dmaengine_terminate_all(dma->chan_using);
 631                 return -ETIMEDOUT;
 632         }
 633
 634         /* Waiting for transfer complete. */
 635         while (1) {
 636                 temp = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2SR);
 637                 if (temp & I2SR_ICF)
 638                         break;
 639                 if (time_after(jiffies, orig_jiffies +
 640                                 msecs_to_jiffies(DMA_TIMEOUT))) {
 641                         dev_dbg(dev, "<%s> Timeout\n", __func__);
 642                         return -ETIMEDOUT;
 643                 }
 644                 schedule();
 645         }
 646
 647         temp = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2CR);
 648         temp &= ~I2CR_DMAEN;
 649         imx_i2c_write_reg(temp, i2c_imx, IMX_I2C_I2CR);
 650
 651         /* The last data byte must be transferred by the CPU. */
 652         imx_i2c_write_reg(msgs->buf[msgs->len-1],
 653                                 i2c_imx, IMX_I2C_I2DR);
 654         result = i2c_imx_trx_complete(i2c_imx);
 655         if (result)
 656                 return result;
 657
 658         return i2c_imx_acked(i2c_imx);
 659 }
 660
 661 static int i2c_imx_dma_read(struct imx_i2c_struct *i2c_imx,
 662                         struct i2c_msg *msgs, bool is_lastmsg)
 663 {
 664         int result;
 665         unsigned long time_left;
 666         unsigned int temp;
 667         unsigned long orig_jiffies = jiffies;
 668         struct imx_i2c_dma *dma = i2c_imx->dma;
 669         struct device *dev = &i2c_imx->adapter.dev;
 670
 671         temp = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2CR);
 672         temp |= I2CR_DMAEN;
 673         imx_i2c_write_reg(temp, i2c_imx, IMX_I2C_I2CR);
 674
 675         dma->chan_using = dma->chan_rx;
 676         dma->dma_transfer_dir = DMA_DEV_TO_MEM;
 677         dma->dma_data_dir = DMA_FROM_DEVICE;
 678         /* The last two data bytes must be transferred by the CPU. */
 679         dma->dma_len = msgs->len - 2;
 680         result = i2c_imx_dma_xfer(i2c_imx, msgs);
 681         if (result)
 682                 return result;
 683
 684         time_left = wait_for_completion_timeout(
 685                                 &i2c_imx->dma->cmd_complete,
 686                                 msecs_to_jiffies(DMA_TIMEOUT));
 687         if (time_left == 0) {
 688                 dmaengine_terminate_all(dma->chan_using);
 689                 return -ETIMEDOUT;
 690         }
 691
 692         /* waiting for transfer complete. */
 693         while (1) {
 694                 temp = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2SR);
 695                 if (temp & I2SR_ICF)
 696                         break;
 697                 if (time_after(jiffies, orig_jiffies +
 698                                 msecs_to_jiffies(DMA_TIMEOUT))) {
 699                         dev_dbg(dev, "<%s> Timeout\n", __func__);
 700                         return -ETIMEDOUT;
 701                 }
 702                 schedule();
 703         }
 704
 705         temp = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2CR);
 706         temp &= ~I2CR_DMAEN;
 707         imx_i2c_write_reg(temp, i2c_imx, IMX_I2C_I2CR);
 708
 709         /* read n-1 byte data */
 710         temp = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2CR);
 711         temp |= I2CR_TXAK;
 712         imx_i2c_write_reg(temp, i2c_imx, IMX_I2C_I2CR);
 713
 714         msgs->buf[msgs->len-2] = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2DR);
 715         /* read n byte data */
 716         result = i2c_imx_trx_complete(i2c_imx);
 717         if (result)
 718                 return result;
 719
 720         if (is_lastmsg) {
 721                 /*
 722                  * It must generate STOP before read I2DR to prevent
 723                  * controller from generating another clock cycle
 724                  */
 725                 dev_dbg(dev, "<%s> clear MSTA\n", __func__);
 726                 temp = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2CR);
 727                 temp &= ~(I2CR_MSTA | I2CR_MTX);
 728                 imx_i2c_write_reg(temp, i2c_imx, IMX_I2C_I2CR);
 729                 i2c_imx_bus_busy(i2c_imx, 0);
 730                 i2c_imx->stopped = 1;
 731         } else {
 732                 /*
 733                  * For i2c master receiver repeat restart operation like:
 734                  * read -> repeat MSTA -> read/write
 735                  * The controller must set MTX before read the last byte in
 736                  * the first read operation, otherwise the first read cost
 737                  * one extra clock cycle.
 738                  */
 739                 temp = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2CR);
 740                 temp |= I2CR_MTX;
 741                 imx_i2c_write_reg(temp, i2c_imx, IMX_I2C_I2CR);
 742         }
 743         msgs->buf[msgs->len-1] = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2DR);
 744
 745         return 0;
 746 }
 747
 748 static int i2c_imx_write(struct imx_i2c_struct *i2c_imx, struct i2c_msg *msgs)
 749 {
 750         int i, result;
 751
 752         dev_dbg(&i2c_imx->adapter.dev, "<%s> write slave address: addr=0x%x\n",
 753                 __func__, i2c_8bit_addr_from_msg(msgs));
 754
 755         /* write slave address */
 756         imx_i2c_write_reg(i2c_8bit_addr_from_msg(msgs), i2c_imx, IMX_I2C_I2DR);
 757         result = i2c_imx_trx_complete(i2c_imx);
 758         if (result)
 759                 return result;
 760         result = i2c_imx_acked(i2c_imx);
 761         if (result)
 762                 return result;
 763         dev_dbg(&i2c_imx->adapter.dev, "<%s> write data\n", __func__);
 764
 765         /* write data */
 766         for (i = 0; i < msgs->len; i++) {
 767                 dev_dbg(&i2c_imx->adapter.dev,
 768                         "<%s> write byte: B%d=0x%X\n",
 769                         __func__, i, msgs->buf[i]);
 770                 imx_i2c_write_reg(msgs->buf[i], i2c_imx, IMX_I2C_I2DR);
 771                 result = i2c_imx_trx_complete(i2c_imx);
 772                 if (result)
 773                         return result;
 774                 result = i2c_imx_acked(i2c_imx);
 775                 if (result)
 776                         return result;
 777         }
 778         return 0;
 779 }
 780
 781 static int i2c_imx_read(struct imx_i2c_struct *i2c_imx, struct i2c_msg *msgs, bool is_lastmsg)
 782 {
 783         int i, result;
 784         unsigned int temp;
 785         int block_data = msgs->flags & I2C_M_RECV_LEN;
 786
 787         dev_dbg(&i2c_imx->adapter.dev,
 788                 "<%s> write slave address: addr=0x%x\n",
 789                 __func__, i2c_8bit_addr_from_msg(msgs));
 790
 791         /* write slave address */
 792         imx_i2c_write_reg(i2c_8bit_addr_from_msg(msgs), i2c_imx, IMX_I2C_I2DR);
 793         result = i2c_imx_trx_complete(i2c_imx);
 794         if (result)
 795                 return result;
 796         result = i2c_imx_acked(i2c_imx);
 797         if (result)
 798                 return result;
 799
 800         dev_dbg(&i2c_imx->adapter.dev, "<%s> setup bus\n", __func__);
 801
 802         /* setup bus to read data */
 803         temp = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2CR);
 804         temp &= ~I2CR_MTX;
 805
 806         /*
 807          * Reset the I2CR_TXAK flag initially for SMBus block read since the
 808          * length is unknown
 809          */
 810         if ((msgs->len - 1) || block_data)
 811                 temp &= ~I2CR_TXAK;
 812         imx_i2c_write_reg(temp, i2c_imx, IMX_I2C_I2CR);
 813         imx_i2c_read_reg(i2c_imx, IMX_I2C_I2DR); /* dummy read */
 814
 815         dev_dbg(&i2c_imx->adapter.dev, "<%s> read data\n", __func__);
 816
 817         if (i2c_imx->dma && msgs->len >= DMA_THRESHOLD && !block_data)
 818                 return i2c_imx_dma_read(i2c_imx, msgs, is_lastmsg);
 819
 820         /* read data */
 821         for (i = 0; i < msgs->len; i++) {
 822                 u8 len = 0;
 823
 824                 result = i2c_imx_trx_complete(i2c_imx);
 825                 if (result)
 826                         return result;
 827                 /*
 828                  * First byte is the length of remaining packet
 829                  * in the SMBus block data read. Add it to
 830                  * msgs->len.
 831                  */
 832                 if ((!i) && block_data) {
 833                         len = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2DR);
 834                         if ((len == 0) || (len > I2C_SMBUS_BLOCK_MAX))
 835                                 return -EPROTO;
 836                         dev_dbg(&i2c_imx->adapter.dev,
 837                                 "<%s> read length: 0x%X\n",
 838                                 __func__, len);
 839                         msgs->len += len;
 840                 }
 841                 if (i == (msgs->len - 1)) {
 842                         if (is_lastmsg) {
 843                                 /*
 844                                  * It must generate STOP before read I2DR to prevent
 845                                  * controller from generating another clock cycle
 846                                  */
 847                                 dev_dbg(&i2c_imx->adapter.dev,
 848                                         "<%s> clear MSTA\n", __func__);
 849                                 temp = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2CR);
 850                                 temp &= ~(I2CR_MSTA | I2CR_MTX);
 851                                 imx_i2c_write_reg(temp, i2c_imx, IMX_I2C_I2CR);
 852                                 i2c_imx_bus_busy(i2c_imx, 0);
 853                                 i2c_imx->stopped = 1;
 854                         } else {
 855                                 /*
 856                                  * For i2c master receiver repeat restart operation like:
 857                                  * read -> repeat MSTA -> read/write
 858                                  * The controller must set MTX before read the last byte in
 859                                  * the first read operation, otherwise the first read cost
 860                                  * one extra clock cycle.
 861                                  */
 862                                 temp = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2CR);
 863                                 temp |= I2CR_MTX;
 864                                 imx_i2c_write_reg(temp, i2c_imx, IMX_I2C_I2CR);
 865                         }
 866                 } else if (i == (msgs->len - 2)) {
 867                         dev_dbg(&i2c_imx->adapter.dev,
 868                                 "<%s> set TXAK\n", __func__);
 869                         temp = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2CR);
 870                         temp |= I2CR_TXAK;
 871                         imx_i2c_write_reg(temp, i2c_imx, IMX_I2C_I2CR);
 872                 }
 873                 if ((!i) && block_data)
 874                         msgs->buf[0] = len;
 875                 else
 876                         msgs->buf[i] = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2DR);
 877                 dev_dbg(&i2c_imx->adapter.dev,
 878                         "<%s> read byte: B%d=0x%X\n",
 879                         __func__, i, msgs->buf[i]);
 880         }
 881         return 0;
 882 }
 883
 884 static int i2c_imx_xfer(struct i2c_adapter *adapter,
 885                                                 struct i2c_msg *msgs, int num)
 886 {
 887         unsigned int i, temp;
 888         int result;
 889         bool is_lastmsg = false;
 890         struct imx_i2c_struct *i2c_imx = i2c_get_adapdata(adapter);
 891
 892         dev_dbg(&i2c_imx->adapter.dev, "<%s>\n", __func__);
 893
 894         result = pm_runtime_get_sync(i2c_imx->adapter.dev.parent);
 895         if (result < 0)
 896                 goto out;
 897
 898         /* Start I2C transfer */
 899         result = i2c_imx_start(i2c_imx);
 900         if (result) {
 901                 if (i2c_imx->adapter.bus_recovery_info) {
 902                         i2c_recover_bus(&i2c_imx->adapter);
 903                         result = i2c_imx_start(i2c_imx);
 904                 }
 905         }
 906
 907         if (result)
 908                 goto fail0;
 909
 910         /* read/write data */
 911         for (i = 0; i < num; i++) {
 912                 if (i == num - 1)
 913                         is_lastmsg = true;
 914
 915                 if (i) {
 916                         dev_dbg(&i2c_imx->adapter.dev,
 917                                 "<%s> repeated start\n", __func__);
 918                         temp = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2CR);
 919                         temp |= I2CR_RSTA;
 920                         imx_i2c_write_reg(temp, i2c_imx, IMX_I2C_I2CR);
 921                         result = i2c_imx_bus_busy(i2c_imx, 1);
 922                         if (result)
 923                                 goto fail0;
 924                 }
 925                 dev_dbg(&i2c_imx->adapter.dev,
 926                         "<%s> transfer message: %d\n", __func__, i);
 927                 /* write/read data */
 928 #ifdef CONFIG_I2C_DEBUG_BUS
 929                 temp = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2CR);
 930                 dev_dbg(&i2c_imx->adapter.dev,
 931                         "<%s> CONTROL: IEN=%d, IIEN=%d, MSTA=%d, MTX=%d, TXAK=%d, RSTA=%d\n",
 932                         __func__,
 933                         (temp & I2CR_IEN ? 1 : 0), (temp & I2CR_IIEN ? 1 : 0),
 934                         (temp & I2CR_MSTA ? 1 : 0), (temp & I2CR_MTX ? 1 : 0),
 935                         (temp & I2CR_TXAK ? 1 : 0), (temp & I2CR_RSTA ? 1 : 0));
 936                 temp = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2SR);
 937                 dev_dbg(&i2c_imx->adapter.dev,
 938                         "<%s> STATUS: ICF=%d, IAAS=%d, IBB=%d, IAL=%d, SRW=%d, IIF=%d, RXAK=%d\n",
 939                         __func__,
 940                         (temp & I2SR_ICF ? 1 : 0), (temp & I2SR_IAAS ? 1 : 0),
 941                         (temp & I2SR_IBB ? 1 : 0), (temp & I2SR_IAL ? 1 : 0),
 942                         (temp & I2SR_SRW ? 1 : 0), (temp & I2SR_IIF ? 1 : 0),
 943                         (temp & I2SR_RXAK ? 1 : 0));
 944 #endif
 945                 if (msgs[i].flags & I2C_M_RD)
 946                         result = i2c_imx_read(i2c_imx, &msgs[i], is_lastmsg);
 947                 else {
 948                         if (i2c_imx->dma && msgs[i].len >= DMA_THRESHOLD)
 949                                 result = i2c_imx_dma_write(i2c_imx, &msgs[i]);
 950                         else
 951                                 result = i2c_imx_write(i2c_imx, &msgs[i]);
 952                 }
 953                 if (result)
 954                         goto fail0;
 955         }
 956
 957 fail0:
 958         /* Stop I2C transfer */
 959         i2c_imx_stop(i2c_imx);
 960
 961         pm_runtime_mark_last_busy(i2c_imx->adapter.dev.parent);
 962         pm_runtime_put_autosuspend(i2c_imx->adapter.dev.parent);
 963
 964 out:
 965         dev_dbg(&i2c_imx->adapter.dev, "<%s> exit with: %s: %d\n", __func__,
 966                 (result < 0) ? "error" : "success msg",
 967                         (result < 0) ? result : num);
 968         return (result < 0) ? result : num;
 969 }
 970
 971 static void i2c_imx_prepare_recovery(struct i2c_adapter *adap)
 972 {
 973         struct imx_i2c_struct *i2c_imx;
 974
 975         i2c_imx = container_of(adap, struct imx_i2c_struct, adapter);
 976
 977         pinctrl_select_state(i2c_imx->pinctrl, i2c_imx->pinctrl_pins_gpio);
 978 }
 979
 980 static void i2c_imx_unprepare_recovery(struct i2c_adapter *adap)
 981 {
 982         struct imx_i2c_struct *i2c_imx;
 983
 984         i2c_imx = container_of(adap, struct imx_i2c_struct, adapter);
 985
 986         pinctrl_select_state(i2c_imx->pinctrl, i2c_imx->pinctrl_pins_default);
 987 }
 988
 989 /*
 990  * We switch SCL and SDA to their GPIO function and do some bitbanging
 991  * for bus recovery. These alternative pinmux settings can be
 992  * described in the device tree by a separate pinctrl state "gpio". If
 993  * this is missing this is not a big problem, the only implication is
 994  * that we can't do bus recovery.
 995  */
 996 static int i2c_imx_init_recovery_info(struct imx_i2c_struct *i2c_imx,
 997                 struct platform_device *pdev)
 998 {
 999         struct i2c_bus_recovery_info *rinfo = &i2c_imx->rinfo;
1000
1001         i2c_imx->pinctrl = devm_pinctrl_get(&pdev->dev);
1002         if (!i2c_imx->pinctrl || IS_ERR(i2c_imx->pinctrl)) {
1003                 dev_info(&pdev->dev, "can't get pinctrl, bus recovery not supported\n");
1004                 return PTR_ERR(i2c_imx->pinctrl);
1005         }
1006
1007         i2c_imx->pinctrl_pins_default = pinctrl_lookup_state(i2c_imx->pinctrl,
1008                         PINCTRL_STATE_DEFAULT);
1009         i2c_imx->pinctrl_pins_gpio = pinctrl_lookup_state(i2c_imx->pinctrl,
1010                         "gpio");
1011         rinfo->sda_gpiod = devm_gpiod_get(&pdev->dev, "sda", GPIOD_IN);
1012         rinfo->scl_gpiod = devm_gpiod_get(&pdev->dev, "scl", GPIOD_OUT_HIGH_OPEN_DRAIN);
1013
1014         if (PTR_ERR(rinfo->sda_gpiod) == -EPROBE_DEFER ||
1015             PTR_ERR(rinfo->scl_gpiod) == -EPROBE_DEFER) {
1016                 return -EPROBE_DEFER;
1017         } else if (IS_ERR(rinfo->sda_gpiod) ||
1018                    IS_ERR(rinfo->scl_gpiod) ||
1019                    IS_ERR(i2c_imx->pinctrl_pins_default) ||
1020                    IS_ERR(i2c_imx->pinctrl_pins_gpio)) {
1021                 dev_dbg(&pdev->dev, "recovery information incomplete\n");
1022                 return 0;
1023         }
1024
1025         dev_dbg(&pdev->dev, "using scl%s for recovery\n",
1026                 rinfo->sda_gpiod ? ",sda" : "");
1027
1028         rinfo->prepare_recovery = i2c_imx_prepare_recovery;
1029         rinfo->unprepare_recovery = i2c_imx_unprepare_recovery;
1030         rinfo->recover_bus = i2c_generic_scl_recovery;
1031         i2c_imx->adapter.bus_recovery_info = rinfo;
1032
1033         return 0;
1034 }
1035
1036 static u32 i2c_imx_func(struct i2c_adapter *adapter)
1037 {
1038         return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL
1039                 | I2C_FUNC_SMBUS_READ_BLOCK_DATA;
1040 }
1041
1042 static const struct i2c_algorithm i2c_imx_algo = {
1043         .master_xfer    = i2c_imx_xfer,
1044         .functionality  = i2c_imx_func,
1045 };
1046
1047 static int i2c_imx_probe(struct platform_device *pdev)
1048 {
1049         const struct of_device_id *of_id = of_match_device(i2c_imx_dt_ids,
1050                                                            &pdev->dev);
1051         struct imx_i2c_struct *i2c_imx;
1052         struct resource *res;
1053         struct imxi2c_platform_data *pdata = dev_get_platdata(&pdev->dev);
1054         void __iomem *base;
1055         int irq, ret;
1056         dma_addr_t phy_addr;
1057
1058         dev_dbg(&pdev->dev, "<%s>\n", __func__);
1059
1060         irq = platform_get_irq(pdev, 0);
1061         if (irq < 0) {
1062                 dev_err(&pdev->dev, "can't get irq number\n");
1063                 return irq;
1064         }
1065
1066         res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
1067         base = devm_ioremap_resource(&pdev->dev, res);
1068         if (IS_ERR(base))
1069                 return PTR_ERR(base);
1070
1071         phy_addr = (dma_addr_t)res->start;
1072         i2c_imx = devm_kzalloc(&pdev->dev, sizeof(*i2c_imx), GFP_KERNEL);
1073         if (!i2c_imx)
1074                 return -ENOMEM;
1075
1076         if (of_id)
1077                 i2c_imx->hwdata = of_id->data;
1078         else
1079                 i2c_imx->hwdata = (struct imx_i2c_hwdata *)
1080                                 platform_get_device_id(pdev)->driver_data;
1081
1082         /* Setup i2c_imx driver structure */
1083         strlcpy(i2c_imx->adapter.name, pdev->name, sizeof(i2c_imx->adapter.name));
1084         i2c_imx->adapter.owner          = THIS_MODULE;
1085         i2c_imx->adapter.algo           = &i2c_imx_algo;
1086         i2c_imx->adapter.dev.parent     = &pdev->dev;
1087         i2c_imx->adapter.nr             = pdev->id;
1088         i2c_imx->adapter.dev.of_node    = pdev->dev.of_node;
1089         i2c_imx->base                   = base;
1090
1091         /* Get I2C clock */
1092         i2c_imx->clk = devm_clk_get(&pdev->dev, NULL);
1093         if (IS_ERR(i2c_imx->clk)) {
1094                 dev_err(&pdev->dev, "can't get I2C clock\n");
1095                 return PTR_ERR(i2c_imx->clk);
1096         }
1097
1098         ret = clk_prepare_enable(i2c_imx->clk);
1099         if (ret) {
1100                 dev_err(&pdev->dev, "can't enable I2C clock, ret=%d\n", ret);
1101                 return ret;
1102         }
1103
1104         /* Request IRQ */
1105         ret = devm_request_irq(&pdev->dev, irq, i2c_imx_isr, IRQF_SHARED,
1106                                 pdev->name, i2c_imx);
1107         if (ret) {
1108                 dev_err(&pdev->dev, "can't claim irq %d\n", irq);
1109                 goto clk_disable;
1110         }
1111
1112         /* Init queue */
1113         init_waitqueue_head(&i2c_imx->queue);
1114
1115         /* Set up adapter data */
1116         i2c_set_adapdata(&i2c_imx->adapter, i2c_imx);
1117
1118         /* Set up platform driver data */
1119         platform_set_drvdata(pdev, i2c_imx);
1120
1121         pm_runtime_set_autosuspend_delay(&pdev->dev, I2C_PM_TIMEOUT);
1122         pm_runtime_use_autosuspend(&pdev->dev);
1123         pm_runtime_set_active(&pdev->dev);
1124         pm_runtime_enable(&pdev->dev);
1125
1126         ret = pm_runtime_get_sync(&pdev->dev);
1127         if (ret < 0)
1128                 goto rpm_disable;
1129
1130         /* Set up clock divider */
1131         i2c_imx->bitrate = IMX_I2C_BIT_RATE;
1132         ret = of_property_read_u32(pdev->dev.of_node,
1133                                    "clock-frequency", &i2c_imx->bitrate);
1134         if (ret < 0 && pdata && pdata->bitrate)
1135                 i2c_imx->bitrate = pdata->bitrate;
1136         i2c_imx->clk_change_nb.notifier_call = i2c_imx_clk_notifier_call;
1137         clk_notifier_register(i2c_imx->clk, &i2c_imx->clk_change_nb);
1138         i2c_imx_set_clk(i2c_imx, clk_get_rate(i2c_imx->clk));
1139
1140         /* Set up chip registers to defaults */
1141         imx_i2c_write_reg(i2c_imx->hwdata->i2cr_ien_opcode ^ I2CR_IEN,
1142                         i2c_imx, IMX_I2C_I2CR);
1143         imx_i2c_write_reg(i2c_imx->hwdata->i2sr_clr_opcode, i2c_imx, IMX_I2C_I2SR);
1144
1145         /* Init optional bus recovery function */
1146         ret = i2c_imx_init_recovery_info(i2c_imx, pdev);
1147         /* Give it another chance if pinctrl used is not ready yet */
1148         if (ret == -EPROBE_DEFER)
1149                 goto clk_notifier_unregister;
1150
1151         /* Add I2C adapter */
1152         ret = i2c_add_numbered_adapter(&i2c_imx->adapter);
1153         if (ret < 0)
1154                 goto clk_notifier_unregister;
1155
1156         pm_runtime_mark_last_busy(&pdev->dev);
1157         pm_runtime_put_autosuspend(&pdev->dev);
1158
1159         dev_dbg(&i2c_imx->adapter.dev, "claimed irq %d\n", irq);
1160         dev_dbg(&i2c_imx->adapter.dev, "device resources: %pR\n", res);
1161         dev_dbg(&i2c_imx->adapter.dev, "adapter name: \"%s\"\n",
1162                 i2c_imx->adapter.name);
1163         dev_info(&i2c_imx->adapter.dev, "IMX I2C adapter registered\n");
1164
1165         /* Init DMA config if supported */
1166         i2c_imx_dma_request(i2c_imx, phy_addr);
1167
1168         return 0;   /* Return OK */
1169
1170 clk_notifier_unregister:
1171         clk_notifier_unregister(i2c_imx->clk, &i2c_imx->clk_change_nb);
1172 rpm_disable:
1173         pm_runtime_put_noidle(&pdev->dev);
1174         pm_runtime_disable(&pdev->dev);
1175         pm_runtime_set_suspended(&pdev->dev);
1176         pm_runtime_dont_use_autosuspend(&pdev->dev);
1177
1178 clk_disable:
1179         clk_disable_unprepare(i2c_imx->clk);
1180         return ret;
1181 }
1182
1183 static int i2c_imx_remove(struct platform_device *pdev)
1184 {
1185         struct imx_i2c_struct *i2c_imx = platform_get_drvdata(pdev);
1186         int ret;
1187
1188         ret = pm_runtime_get_sync(&pdev->dev);
1189         if (ret < 0)
1190                 return ret;
1191
1192         /* remove adapter */
1193         dev_dbg(&i2c_imx->adapter.dev, "adapter removed\n");
1194         i2c_del_adapter(&i2c_imx->adapter);
1195
1196         if (i2c_imx->dma)
1197                 i2c_imx_dma_free(i2c_imx);
1198
1199         /* setup chip registers to defaults */
1200         imx_i2c_write_reg(0, i2c_imx, IMX_I2C_IADR);
1201         imx_i2c_write_reg(0, i2c_imx, IMX_I2C_IFDR);
1202         imx_i2c_write_reg(0, i2c_imx, IMX_I2C_I2CR);
1203         imx_i2c_write_reg(0, i2c_imx, IMX_I2C_I2SR);
1204
1205         clk_notifier_unregister(i2c_imx->clk, &i2c_imx->clk_change_nb);
1206         clk_disable_unprepare(i2c_imx->clk);
1207
1208         pm_runtime_put_noidle(&pdev->dev);
1209         pm_runtime_disable(&pdev->dev);
1210
1211         return 0;
1212 }
1213
1214 #ifdef CONFIG_PM
1215 static int i2c_imx_runtime_suspend(struct device *dev)
1216 {
1217         struct imx_i2c_struct *i2c_imx = dev_get_drvdata(dev);
1218
1219         clk_disable(i2c_imx->clk);
1220
1221         return 0;
1222 }
1223
1224 static int i2c_imx_runtime_resume(struct device *dev)
1225 {
1226         struct imx_i2c_struct *i2c_imx = dev_get_drvdata(dev);
1227         int ret;
1228
1229         ret = clk_enable(i2c_imx->clk);
1230         if (ret)
1231                 dev_err(dev, "can't enable I2C clock, ret=%d\n", ret);
1232
1233         return ret;
1234 }
1235
1236 static const struct dev_pm_ops i2c_imx_pm_ops = {
1237         SET_RUNTIME_PM_OPS(i2c_imx_runtime_suspend,
1238                            i2c_imx_runtime_resume, NULL)
1239 };
1240 #define I2C_IMX_PM_OPS (&i2c_imx_pm_ops)
1241 #else
1242 #define I2C_IMX_PM_OPS NULL
1243 #endif /* CONFIG_PM */
1244
1245 static struct platform_driver i2c_imx_driver = {
1246         .probe = i2c_imx_probe,
1247         .remove = i2c_imx_remove,
1248         .driver = {
1249                 .name = DRIVER_NAME,
1250                 .pm = I2C_IMX_PM_OPS,
1251                 .of_match_table = i2c_imx_dt_ids,
1252         },
1253         .id_table = imx_i2c_devtype,
1254 };
1255
1256 static int __init i2c_adap_imx_init(void)
1257 {
1258         return platform_driver_register(&i2c_imx_driver);
1259 }
1260 subsys_initcall(i2c_adap_imx_init);
1261
1262 static void __exit i2c_adap_imx_exit(void)
1263 {
1264         platform_driver_unregister(&i2c_imx_driver);
1265 }
1266 module_exit(i2c_adap_imx_exit);
1267
1268 MODULE_LICENSE("GPL");
1269 MODULE_AUTHOR("Darius Augulis");
1270 MODULE_DESCRIPTION("I2C adapter driver for IMX I2C bus");
1271 MODULE_ALIAS("platform:" DRIVER_NAME);