arch/arm/boot/dts/qcom-pm8941.dtsi

   1 #include <dt-bindings/iio/qcom,spmi-vadc.h>
   2 #include <dt-bindings/interrupt-controller/irq.h>
   3 #include <dt-bindings/spmi/spmi.h>
   4
   5 &spmi_bus {
   6
   7         pm8941_0: pm8941@0 {
   8                 compatible = "qcom,pm8941", "qcom,spmi-pmic";
   9                 reg = <0x0 SPMI_USID>;
  10                 #address-cells = <1>;
  11                 #size-cells = <0>;
  12
  13                 rtc@6000 {
  14                         compatible = "qcom,pm8941-rtc";
  15                         reg = <0x6000>,
  16                               <0x6100>;
  17                         reg-names = "rtc", "alarm";
  18                         interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
  19                 };
  20
  21                 pwrkey@800 {
  22                         compatible = "qcom,pm8941-pwrkey";
  23                         reg = <0x800>;
  24                         interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
  25                         debounce = <15625>;
  26                         bias-pull-up;
  27                 };
  28
  29                 charger@1000 {
  30                         compatible = "qcom,pm8941-charger";
  31                         reg = <0x1000>;
  32                         interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>,
  33                                      <0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>,
  34                                      <0x0 0x10 4 IRQ_TYPE_EDGE_BOTH>,
  35                                      <0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>,
  36                                      <0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>,
  37                                      <0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>,
  38                                      <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>,
  39                                      <0x0 0x14 1 IRQ_TYPE_EDGE_BOTH>;
  40                         interrupt-names = "chg-done",
  41                                           "chg-fast",
  42                                           "chg-trkl",
  43                                           "bat-temp-ok",
  44                                           "bat-present",
  45                                           "chg-gone",
  46                                           "usb-valid",
  47                                           "dc-valid";
  48
  49                         usb-otg-in-supply = <&pm8941_5vs1>;
  50
  51                         chg_otg: otg-vbus { };
  52                 };
  53
  54                 pm8941_gpios: gpios@c000 {
  55                         compatible = "qcom,pm8941-gpio", "qcom,spmi-gpio";
  56                         reg = <0xc000>;
  57                         gpio-controller;
  58                         #gpio-cells = <2>;
  59                         interrupts = <0 0xc0 0 IRQ_TYPE_NONE>,
  60                                      <0 0xc1 0 IRQ_TYPE_NONE>,
  61                                      <0 0xc2 0 IRQ_TYPE_NONE>,
  62                                      <0 0xc3 0 IRQ_TYPE_NONE>,
  63                                      <0 0xc4 0 IRQ_TYPE_NONE>,
  64                                      <0 0xc5 0 IRQ_TYPE_NONE>,
  65                                      <0 0xc6 0 IRQ_TYPE_NONE>,
  66                                      <0 0xc7 0 IRQ_TYPE_NONE>,
  67                                      <0 0xc8 0 IRQ_TYPE_NONE>,
  68                                      <0 0xc9 0 IRQ_TYPE_NONE>,
  69                                      <0 0xca 0 IRQ_TYPE_NONE>,
  70                                      <0 0xcb 0 IRQ_TYPE_NONE>,
  71                                      <0 0xcc 0 IRQ_TYPE_NONE>,
  72                                      <0 0xcd 0 IRQ_TYPE_NONE>,
  73                                      <0 0xce 0 IRQ_TYPE_NONE>,
  74                                      <0 0xcf 0 IRQ_TYPE_NONE>,
  75                                      <0 0xd0 0 IRQ_TYPE_NONE>,
  76                                      <0 0xd1 0 IRQ_TYPE_NONE>,
  77                                      <0 0xd2 0 IRQ_TYPE_NONE>,
  78                                      <0 0xd3 0 IRQ_TYPE_NONE>,
  79                                      <0 0xd4 0 IRQ_TYPE_NONE>,
  80                                      <0 0xd5 0 IRQ_TYPE_NONE>,
  81                                      <0 0xd6 0 IRQ_TYPE_NONE>,
  82                                      <0 0xd7 0 IRQ_TYPE_NONE>,
  83                                      <0 0xd8 0 IRQ_TYPE_NONE>,
  84                                      <0 0xd9 0 IRQ_TYPE_NONE>,
  85                                      <0 0xda 0 IRQ_TYPE_NONE>,
  86                                      <0 0xdb 0 IRQ_TYPE_NONE>,
  87                                      <0 0xdc 0 IRQ_TYPE_NONE>,
  88                                      <0 0xdd 0 IRQ_TYPE_NONE>,
  89                                      <0 0xde 0 IRQ_TYPE_NONE>,
  90                                      <0 0xdf 0 IRQ_TYPE_NONE>,
  91                                      <0 0xe0 0 IRQ_TYPE_NONE>,
  92                                      <0 0xe1 0 IRQ_TYPE_NONE>,
  93                                      <0 0xe2 0 IRQ_TYPE_NONE>,
  94                                      <0 0xe3 0 IRQ_TYPE_NONE>;
  95
  96                         boost_bypass_n_pin: boost-bypass {
  97                                 pins = "gpio21";
  98                                 function = "normal";
  99                         };
 100                 };
 101
 102                 pm8941_mpps: mpps@a000 {
 103                         compatible = "qcom,pm8941-mpp", "qcom,spmi-mpp";
 104                         reg = <0xa000>;
 105                         gpio-controller;
 106                         #gpio-cells = <2>;
 107                         interrupts = <0 0xa0 0 IRQ_TYPE_NONE>,
 108                                      <0 0xa1 0 IRQ_TYPE_NONE>,
 109                                      <0 0xa2 0 IRQ_TYPE_NONE>,
 110                                      <0 0xa3 0 IRQ_TYPE_NONE>,
 111                                      <0 0xa4 0 IRQ_TYPE_NONE>,
 112                                      <0 0xa5 0 IRQ_TYPE_NONE>,
 113                                      <0 0xa6 0 IRQ_TYPE_NONE>,
 114                                      <0 0xa7 0 IRQ_TYPE_NONE>;
 115                 };
 116
 117                 pm8941_temp: temp-alarm@2400 {
 118                         compatible = "qcom,spmi-temp-alarm";
 119                         reg = <0x2400>;
 120                         interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>;
 121                         io-channels = <&pm8941_vadc VADC_DIE_TEMP>;
 122                         io-channel-names = "thermal";
 123                         #thermal-sensor-cells = <0>;
 124                 };
 125
 126                 pm8941_vadc: vadc@3100 {
 127                         compatible = "qcom,spmi-vadc";
 128                         reg = <0x3100>;
 129                         interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
 130                         #address-cells = <1>;
 131                         #size-cells = <0>;
 132                         #io-channel-cells = <1>;
 133
 134                         die_temp {
 135                                 reg = <VADC_DIE_TEMP>;
 136                         };
 137                         ref_625mv {
 138                                 reg = <VADC_REF_625MV>;
 139                         };
 140                         ref_1250v {
 141                                 reg = <VADC_REF_1250MV>;
 142                         };
 143                         ref_gnd {
 144                                 reg = <VADC_GND_REF>;
 145                         };
 146                         ref_vdd {
 147                                 reg = <VADC_VDD_VADC>;
 148                         };
 149                 };
 150
 151                 pm8941_iadc: iadc@3600 {
 152                         compatible = "qcom,pm8941-iadc", "qcom,spmi-iadc";
 153                         reg = <0x3600>;
 154                         interrupts = <0x0 0x36 0x0 IRQ_TYPE_EDGE_RISING>;
 155                         qcom,external-resistor-micro-ohms = <10000>;
 156                 };
 157
 158                 coincell@2800 {
 159                         compatible = "qcom,pm8941-coincell";
 160                         reg = <0x2800>;
 161                         status = "disabled";
 162                 };
 163         };
 164
 165         pm8941_1: pm8941@1 {
 166                 compatible = "qcom,pm8941", "qcom,spmi-pmic";
 167                 reg = <0x1 SPMI_USID>;
 168                 #address-cells = <1>;
 169                 #size-cells = <0>;
 170
 171                 pm8941_wled: wled@d800 {
 172                         compatible = "qcom,pm8941-wled";
 173                         reg = <0xd800>;
 174                         label = "backlight";
 175
 176                         status = "disabled";
 177                 };
 178         };
 179 };