drivers/power/supply/pm2301_charger.c

   1 // SPDX-License-Identifier: GPL-2.0-only
   2 /*
   3  * Copyright 2012 ST Ericsson.
   4  *
   5  * Power supply driver for ST Ericsson pm2xxx_charger charger
   6  */
   7
   8 #include <linux/init.h>
   9 #include <linux/module.h>
  10 #include <linux/device.h>
  11 #include <linux/interrupt.h>
  12 #include <linux/delay.h>
  13 #include <linux/slab.h>
  14 #include <linux/platform_device.h>
  15 #include <linux/power_supply.h>
  16 #include <linux/regulator/consumer.h>
  17 #include <linux/err.h>
  18 #include <linux/i2c.h>
  19 #include <linux/workqueue.h>
  20 #include <linux/mfd/abx500/ab8500.h>
  21 #include <linux/mfd/abx500/ab8500-bm.h>
  22 #include <linux/mfd/abx500/ux500_chargalg.h>
  23 #include <linux/pm2301_charger.h>
  24 #include <linux/gpio.h>
  25 #include <linux/pm_runtime.h>
  26 #include <linux/pm.h>
  27
  28 #include "pm2301_charger.h"
  29
  30 #define to_pm2xxx_charger_ac_device_info(x) container_of((x), \
  31                 struct pm2xxx_charger, ac_chg)
  32 #define SLEEP_MIN               50
  33 #define SLEEP_MAX               100
  34 #define PM2XXX_AUTOSUSPEND_DELAY 500
  35
  36 static int pm2xxx_interrupt_registers[] = {
  37         PM2XXX_REG_INT1,
  38         PM2XXX_REG_INT2,
  39         PM2XXX_REG_INT3,
  40         PM2XXX_REG_INT4,
  41         PM2XXX_REG_INT5,
  42         PM2XXX_REG_INT6,
  43 };
  44
  45 static enum power_supply_property pm2xxx_charger_ac_props[] = {
  46         POWER_SUPPLY_PROP_HEALTH,
  47         POWER_SUPPLY_PROP_PRESENT,
  48         POWER_SUPPLY_PROP_ONLINE,
  49         POWER_SUPPLY_PROP_VOLTAGE_AVG,
  50 };
  51
  52 static int pm2xxx_charger_voltage_map[] = {
  53         3500,
  54         3525,
  55         3550,
  56         3575,
  57         3600,
  58         3625,
  59         3650,
  60         3675,
  61         3700,
  62         3725,
  63         3750,
  64         3775,
  65         3800,
  66         3825,
  67         3850,
  68         3875,
  69         3900,
  70         3925,
  71         3950,
  72         3975,
  73         4000,
  74         4025,
  75         4050,
  76         4075,
  77         4100,
  78         4125,
  79         4150,
  80         4175,
  81         4200,
  82         4225,
  83         4250,
  84         4275,
  85         4300,
  86 };
  87
  88 static int pm2xxx_charger_current_map[] = {
  89         200,
  90         200,
  91         400,
  92         600,
  93         800,
  94         1000,
  95         1200,
  96         1400,
  97         1600,
  98         1800,
  99         2000,
 100         2200,
 101         2400,
 102         2600,
 103         2800,
 104         3000,
 105 };
 106
 107 static const struct i2c_device_id pm2xxx_ident[] = {
 108         { "pm2301", 0 },
 109         { }
 110 };
 111
 112 static void set_lpn_pin(struct pm2xxx_charger *pm2)
 113 {
 114         if (!pm2->ac.charger_connected && gpio_is_valid(pm2->lpn_pin)) {
 115                 gpio_set_value(pm2->lpn_pin, 1);
 116                 usleep_range(SLEEP_MIN, SLEEP_MAX);
 117         }
 118 }
 119
 120 static void clear_lpn_pin(struct pm2xxx_charger *pm2)
 121 {
 122         if (!pm2->ac.charger_connected && gpio_is_valid(pm2->lpn_pin))
 123                 gpio_set_value(pm2->lpn_pin, 0);
 124 }
 125
 126 static int pm2xxx_reg_read(struct pm2xxx_charger *pm2, int reg, u8 *val)
 127 {
 128         int ret;
 129
 130         /* wake up the device */
 131         pm_runtime_get_sync(pm2->dev);
 132
 133         ret = i2c_smbus_read_i2c_block_data(pm2->config.pm2xxx_i2c, reg,
 134                                 1, val);
 135         if (ret < 0)
 136                 dev_err(pm2->dev, "Error reading register at 0x%x\n", reg);
 137         else
 138                 ret = 0;
 139
 140         pm_runtime_put_sync(pm2->dev);
 141
 142         return ret;
 143 }
 144
 145 static int pm2xxx_reg_write(struct pm2xxx_charger *pm2, int reg, u8 val)
 146 {
 147         int ret;
 148
 149         /* wake up the device */
 150         pm_runtime_get_sync(pm2->dev);
 151
 152         ret = i2c_smbus_write_i2c_block_data(pm2->config.pm2xxx_i2c, reg,
 153                                 1, &val);
 154         if (ret < 0)
 155                 dev_err(pm2->dev, "Error writing register at 0x%x\n", reg);
 156         else
 157                 ret = 0;
 158
 159         pm_runtime_put_sync(pm2->dev);
 160
 161         return ret;
 162 }
 163
 164 static int pm2xxx_charging_enable_mngt(struct pm2xxx_charger *pm2)
 165 {
 166         int ret;
 167
 168         /* Enable charging */
 169         ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG2,
 170                         (PM2XXX_CH_AUTO_RESUME_EN | PM2XXX_CHARGER_ENA));
 171
 172         return ret;
 173 }
 174
 175 static int pm2xxx_charging_disable_mngt(struct pm2xxx_charger *pm2)
 176 {
 177         int ret;
 178
 179         /* Disable SW EOC ctrl */
 180         ret = pm2xxx_reg_write(pm2, PM2XXX_SW_CTRL_REG, PM2XXX_SWCTRL_HW);
 181         if (ret < 0) {
 182                 dev_err(pm2->dev, "%s pm2xxx write failed\n", __func__);
 183                 return ret;
 184         }
 185
 186         /* Disable charging */
 187         ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG2,
 188                         (PM2XXX_CH_AUTO_RESUME_DIS | PM2XXX_CHARGER_DIS));
 189         if (ret < 0) {
 190                 dev_err(pm2->dev, "%s pm2xxx write failed\n", __func__);
 191                 return ret;
 192         }
 193
 194         return 0;
 195 }
 196
 197 static int pm2xxx_charger_batt_therm_mngt(struct pm2xxx_charger *pm2, int val)
 198 {
 199         queue_work(pm2->charger_wq, &pm2->check_main_thermal_prot_work);
 200
 201         return 0;
 202 }
 203
 204
 205 static int pm2xxx_charger_die_therm_mngt(struct pm2xxx_charger *pm2, int val)
 206 {
 207         queue_work(pm2->charger_wq, &pm2->check_main_thermal_prot_work);
 208
 209         return 0;
 210 }
 211
 212 static int pm2xxx_charger_ovv_mngt(struct pm2xxx_charger *pm2, int val)
 213 {
 214         dev_err(pm2->dev, "Overvoltage detected\n");
 215         pm2->flags.ovv = true;
 216         power_supply_changed(pm2->ac_chg.psy);
 217
 218         /* Schedule a new HW failure check */
 219         queue_delayed_work(pm2->charger_wq, &pm2->check_hw_failure_work, 0);
 220
 221         return 0;
 222 }
 223
 224 static int pm2xxx_charger_wd_exp_mngt(struct pm2xxx_charger *pm2, int val)
 225 {
 226         dev_dbg(pm2->dev , "20 minutes watchdog expired\n");
 227
 228         pm2->ac.wd_expired = true;
 229         power_supply_changed(pm2->ac_chg.psy);
 230
 231         return 0;
 232 }
 233
 234 static int pm2xxx_charger_vbat_lsig_mngt(struct pm2xxx_charger *pm2, int val)
 235 {
 236         int ret;
 237
 238         switch (val) {
 239         case PM2XXX_INT1_ITVBATLOWR:
 240                 dev_dbg(pm2->dev, "VBAT grows above VBAT_LOW level\n");
 241                 /* Enable SW EOC ctrl */
 242                 ret = pm2xxx_reg_write(pm2, PM2XXX_SW_CTRL_REG,
 243                                                         PM2XXX_SWCTRL_SW);
 244                 if (ret < 0) {
 245                         dev_err(pm2->dev, "%s pm2xxx write failed\n", __func__);
 246                         return ret;
 247                 }
 248                 break;
 249
 250         case PM2XXX_INT1_ITVBATLOWF:
 251                 dev_dbg(pm2->dev, "VBAT drops below VBAT_LOW level\n");
 252                 /* Disable SW EOC ctrl */
 253                 ret = pm2xxx_reg_write(pm2, PM2XXX_SW_CTRL_REG,
 254                                                         PM2XXX_SWCTRL_HW);
 255                 if (ret < 0) {
 256                         dev_err(pm2->dev, "%s pm2xxx write failed\n", __func__);
 257                         return ret;
 258                 }
 259                 break;
 260
 261         default:
 262                 dev_err(pm2->dev, "Unknown VBAT level\n");
 263         }
 264
 265         return 0;
 266 }
 267
 268 static int pm2xxx_charger_bat_disc_mngt(struct pm2xxx_charger *pm2, int val)
 269 {
 270         dev_dbg(pm2->dev, "battery disconnected\n");
 271
 272         return 0;
 273 }
 274
 275 static int pm2xxx_charger_detection(struct pm2xxx_charger *pm2, u8 *val)
 276 {
 277         int ret;
 278
 279         ret = pm2xxx_reg_read(pm2, PM2XXX_SRCE_REG_INT2, val);
 280
 281         if (ret < 0) {
 282                 dev_err(pm2->dev, "Charger detection failed\n");
 283                 goto out;
 284         }
 285
 286         *val &= (PM2XXX_INT2_S_ITVPWR1PLUG | PM2XXX_INT2_S_ITVPWR2PLUG);
 287
 288 out:
 289         return ret;
 290 }
 291
 292 static int pm2xxx_charger_itv_pwr_plug_mngt(struct pm2xxx_charger *pm2, int val)
 293 {
 294
 295         int ret;
 296         u8 read_val;
 297
 298         /*
 299          * Since we can't be sure that the events are received
 300          * synchronously, we have the check if the main charger is
 301          * connected by reading the interrupt source register.
 302          */
 303         ret = pm2xxx_charger_detection(pm2, &read_val);
 304
 305         if ((ret == 0) && read_val) {
 306                 pm2->ac.charger_connected = 1;
 307                 pm2->ac_conn = true;
 308                 queue_work(pm2->charger_wq, &pm2->ac_work);
 309         }
 310
 311
 312         return ret;
 313 }
 314
 315 static int pm2xxx_charger_itv_pwr_unplug_mngt(struct pm2xxx_charger *pm2,
 316                                                                 int val)
 317 {
 318         pm2->ac.charger_connected = 0;
 319         queue_work(pm2->charger_wq, &pm2->ac_work);
 320
 321         return 0;
 322 }
 323
 324 static int pm2_int_reg0(void *pm2_data, int val)
 325 {
 326         struct pm2xxx_charger *pm2 = pm2_data;
 327         int ret = 0;
 328
 329         if (val & PM2XXX_INT1_ITVBATLOWR) {
 330                 ret = pm2xxx_charger_vbat_lsig_mngt(pm2,
 331                                                 PM2XXX_INT1_ITVBATLOWR);
 332                 if (ret < 0)
 333                         goto out;
 334         }
 335
 336         if (val & PM2XXX_INT1_ITVBATLOWF) {
 337                 ret = pm2xxx_charger_vbat_lsig_mngt(pm2,
 338                                                 PM2XXX_INT1_ITVBATLOWF);
 339                 if (ret < 0)
 340                         goto out;
 341         }
 342
 343         if (val & PM2XXX_INT1_ITVBATDISCONNECT) {
 344                 ret = pm2xxx_charger_bat_disc_mngt(pm2,
 345                                 PM2XXX_INT1_ITVBATDISCONNECT);
 346                 if (ret < 0)
 347                         goto out;
 348         }
 349 out:
 350         return ret;
 351 }
 352
 353 static int pm2_int_reg1(void *pm2_data, int val)
 354 {
 355         struct pm2xxx_charger *pm2 = pm2_data;
 356         int ret = 0;
 357
 358         if (val & (PM2XXX_INT2_ITVPWR1PLUG | PM2XXX_INT2_ITVPWR2PLUG)) {
 359                 dev_dbg(pm2->dev , "Main charger plugged\n");
 360                 ret = pm2xxx_charger_itv_pwr_plug_mngt(pm2, val &
 361                         (PM2XXX_INT2_ITVPWR1PLUG | PM2XXX_INT2_ITVPWR2PLUG));
 362         }
 363
 364         if (val &
 365                 (PM2XXX_INT2_ITVPWR1UNPLUG | PM2XXX_INT2_ITVPWR2UNPLUG)) {
 366                 dev_dbg(pm2->dev , "Main charger unplugged\n");
 367                 ret = pm2xxx_charger_itv_pwr_unplug_mngt(pm2, val &
 368                                                 (PM2XXX_INT2_ITVPWR1UNPLUG |
 369                                                 PM2XXX_INT2_ITVPWR2UNPLUG));
 370         }
 371
 372         return ret;
 373 }
 374
 375 static int pm2_int_reg2(void *pm2_data, int val)
 376 {
 377         struct pm2xxx_charger *pm2 = pm2_data;
 378         int ret = 0;
 379
 380         if (val & PM2XXX_INT3_ITAUTOTIMEOUTWD)
 381                 ret = pm2xxx_charger_wd_exp_mngt(pm2, val);
 382
 383         if (val & (PM2XXX_INT3_ITCHPRECHARGEWD |
 384                                 PM2XXX_INT3_ITCHCCWD | PM2XXX_INT3_ITCHCVWD)) {
 385                 dev_dbg(pm2->dev,
 386                         "Watchdog occurred for precharge, CC and CV charge\n");
 387         }
 388
 389         return ret;
 390 }
 391
 392 static int pm2_int_reg3(void *pm2_data, int val)
 393 {
 394         struct pm2xxx_charger *pm2 = pm2_data;
 395         int ret = 0;
 396
 397         if (val & (PM2XXX_INT4_ITCHARGINGON)) {
 398                 dev_dbg(pm2->dev ,
 399                         "chargind operation has started\n");
 400         }
 401
 402         if (val & (PM2XXX_INT4_ITVRESUME)) {
 403                 dev_dbg(pm2->dev,
 404                         "battery discharged down to VResume threshold\n");
 405         }
 406
 407         if (val & (PM2XXX_INT4_ITBATTFULL)) {
 408                 dev_dbg(pm2->dev , "battery fully detected\n");
 409         }
 410
 411         if (val & (PM2XXX_INT4_ITCVPHASE)) {
 412                 dev_dbg(pm2->dev, "CV phase enter with 0.5C charging\n");
 413         }
 414
 415         if (val & (PM2XXX_INT4_ITVPWR2OVV | PM2XXX_INT4_ITVPWR1OVV)) {
 416                 pm2->failure_case = VPWR_OVV;
 417                 ret = pm2xxx_charger_ovv_mngt(pm2, val &
 418                         (PM2XXX_INT4_ITVPWR2OVV | PM2XXX_INT4_ITVPWR1OVV));
 419                 dev_dbg(pm2->dev, "VPWR/VSYSTEM overvoltage detected\n");
 420         }
 421
 422         if (val & (PM2XXX_INT4_S_ITBATTEMPCOLD |
 423                                 PM2XXX_INT4_S_ITBATTEMPHOT)) {
 424                 ret = pm2xxx_charger_batt_therm_mngt(pm2, val &
 425                         (PM2XXX_INT4_S_ITBATTEMPCOLD |
 426                         PM2XXX_INT4_S_ITBATTEMPHOT));
 427                 dev_dbg(pm2->dev, "BTEMP is too Low/High\n");
 428         }
 429
 430         return ret;
 431 }
 432
 433 static int pm2_int_reg4(void *pm2_data, int val)
 434 {
 435         struct pm2xxx_charger *pm2 = pm2_data;
 436         int ret = 0;
 437
 438         if (val & PM2XXX_INT5_ITVSYSTEMOVV) {
 439                 pm2->failure_case = VSYSTEM_OVV;
 440                 ret = pm2xxx_charger_ovv_mngt(pm2, val &
 441                                                 PM2XXX_INT5_ITVSYSTEMOVV);
 442                 dev_dbg(pm2->dev, "VSYSTEM overvoltage detected\n");
 443         }
 444
 445         if (val & (PM2XXX_INT5_ITTHERMALWARNINGFALL |
 446                                 PM2XXX_INT5_ITTHERMALWARNINGRISE |
 447                                 PM2XXX_INT5_ITTHERMALSHUTDOWNFALL |
 448                                 PM2XXX_INT5_ITTHERMALSHUTDOWNRISE)) {
 449                 dev_dbg(pm2->dev, "BTEMP die temperature is too Low/High\n");
 450                 ret = pm2xxx_charger_die_therm_mngt(pm2, val &
 451                         (PM2XXX_INT5_ITTHERMALWARNINGFALL |
 452                         PM2XXX_INT5_ITTHERMALWARNINGRISE |
 453                         PM2XXX_INT5_ITTHERMALSHUTDOWNFALL |
 454                         PM2XXX_INT5_ITTHERMALSHUTDOWNRISE));
 455         }
 456
 457         return ret;
 458 }
 459
 460 static int pm2_int_reg5(void *pm2_data, int val)
 461 {
 462         struct pm2xxx_charger *pm2 = pm2_data;
 463         int ret = 0;
 464
 465         if (val & (PM2XXX_INT6_ITVPWR2DROP | PM2XXX_INT6_ITVPWR1DROP)) {
 466                 dev_dbg(pm2->dev, "VMPWR drop to VBAT level\n");
 467         }
 468
 469         if (val & (PM2XXX_INT6_ITVPWR2VALIDRISE |
 470                         PM2XXX_INT6_ITVPWR1VALIDRISE |
 471                         PM2XXX_INT6_ITVPWR2VALIDFALL |
 472                         PM2XXX_INT6_ITVPWR1VALIDFALL)) {
 473                 dev_dbg(pm2->dev, "Falling/Rising edge on WPWR1/2\n");
 474         }
 475
 476         return ret;
 477 }
 478
 479 static irqreturn_t  pm2xxx_irq_int(int irq, void *data)
 480 {
 481         struct pm2xxx_charger *pm2 = data;
 482         struct pm2xxx_interrupts *interrupt = pm2->pm2_int;
 483         int i;
 484
 485         /* wake up the device */
 486         pm_runtime_get_sync(pm2->dev);
 487
 488         do {
 489                 for (i = 0; i < PM2XXX_NUM_INT_REG; i++) {
 490                         pm2xxx_reg_read(pm2,
 491                                 pm2xxx_interrupt_registers[i],
 492                                 &(interrupt->reg[i]));
 493
 494                         if (interrupt->reg[i] > 0)
 495                                 interrupt->handler[i](pm2, interrupt->reg[i]);
 496                 }
 497         } while (gpio_get_value(pm2->pdata->gpio_irq_number) == 0);
 498
 499         pm_runtime_mark_last_busy(pm2->dev);
 500         pm_runtime_put_autosuspend(pm2->dev);
 501
 502         return IRQ_HANDLED;
 503 }
 504
 505 static int pm2xxx_charger_get_ac_cv(struct pm2xxx_charger *pm2)
 506 {
 507         int ret = 0;
 508         u8 val;
 509
 510         if (pm2->ac.charger_connected && pm2->ac.charger_online) {
 511
 512                 ret = pm2xxx_reg_read(pm2, PM2XXX_SRCE_REG_INT4, &val);
 513                 if (ret < 0) {
 514                         dev_err(pm2->dev, "%s pm2xxx read failed\n", __func__);
 515                         goto out;
 516                 }
 517
 518                 if (val & PM2XXX_INT4_S_ITCVPHASE)
 519                         ret = PM2XXX_CONST_VOLT;
 520                 else
 521                         ret = PM2XXX_CONST_CURR;
 522         }
 523 out:
 524         return ret;
 525 }
 526
 527 static int pm2xxx_current_to_regval(int curr)
 528 {
 529         int i;
 530
 531         if (curr < pm2xxx_charger_current_map[0])
 532                 return 0;
 533
 534         for (i = 1; i < ARRAY_SIZE(pm2xxx_charger_current_map); i++) {
 535                 if (curr < pm2xxx_charger_current_map[i])
 536                         return (i - 1);
 537         }
 538
 539         i = ARRAY_SIZE(pm2xxx_charger_current_map) - 1;
 540         if (curr == pm2xxx_charger_current_map[i])
 541                 return i;
 542         else
 543                 return -EINVAL;
 544 }
 545
 546 static int pm2xxx_voltage_to_regval(int curr)
 547 {
 548         int i;
 549
 550         if (curr < pm2xxx_charger_voltage_map[0])
 551                 return 0;
 552
 553         for (i = 1; i < ARRAY_SIZE(pm2xxx_charger_voltage_map); i++) {
 554                 if (curr < pm2xxx_charger_voltage_map[i])
 555                         return i - 1;
 556         }
 557
 558         i = ARRAY_SIZE(pm2xxx_charger_voltage_map) - 1;
 559         if (curr == pm2xxx_charger_voltage_map[i])
 560                 return i;
 561         else
 562                 return -EINVAL;
 563 }
 564
 565 static int pm2xxx_charger_update_charger_current(struct ux500_charger *charger,
 566                 int ich_out)
 567 {
 568         int ret;
 569         int curr_index;
 570         struct pm2xxx_charger *pm2;
 571         u8 val;
 572
 573         if (charger->psy->desc->type == POWER_SUPPLY_TYPE_MAINS)
 574                 pm2 = to_pm2xxx_charger_ac_device_info(charger);
 575         else
 576                 return -ENXIO;
 577
 578         curr_index = pm2xxx_current_to_regval(ich_out);
 579         if (curr_index < 0) {
 580                 dev_err(pm2->dev,
 581                         "Charger current too high, charging not started\n");
 582                 return -ENXIO;
 583         }
 584
 585         ret = pm2xxx_reg_read(pm2, PM2XXX_BATT_CTRL_REG6, &val);
 586         if (ret >= 0) {
 587                 val &= ~PM2XXX_DIR_CH_CC_CURRENT_MASK;
 588                 val |= curr_index;
 589                 ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG6, val);
 590                 if (ret < 0) {
 591                         dev_err(pm2->dev,
 592                                 "%s write failed\n", __func__);
 593                 }
 594         }
 595         else
 596                 dev_err(pm2->dev, "%s read failed\n", __func__);
 597
 598         return ret;
 599 }
 600
 601 static int pm2xxx_charger_ac_get_property(struct power_supply *psy,
 602         enum power_supply_property psp,
 603         union power_supply_propval *val)
 604 {
 605         struct pm2xxx_charger *pm2;
 606
 607         pm2 = to_pm2xxx_charger_ac_device_info(psy_to_ux500_charger(psy));
 608
 609         switch (psp) {
 610         case POWER_SUPPLY_PROP_HEALTH:
 611                 if (pm2->flags.mainextchnotok)
 612                         val->intval = POWER_SUPPLY_HEALTH_UNSPEC_FAILURE;
 613                 else if (pm2->ac.wd_expired)
 614                         val->intval = POWER_SUPPLY_HEALTH_DEAD;
 615                 else if (pm2->flags.main_thermal_prot)
 616                         val->intval = POWER_SUPPLY_HEALTH_OVERHEAT;
 617                 else if (pm2->flags.ovv)
 618                         val->intval = POWER_SUPPLY_HEALTH_OVERVOLTAGE;
 619                 else
 620                         val->intval = POWER_SUPPLY_HEALTH_GOOD;
 621                 break;
 622         case POWER_SUPPLY_PROP_ONLINE:
 623                 val->intval = pm2->ac.charger_online;
 624                 break;
 625         case POWER_SUPPLY_PROP_PRESENT:
 626                 val->intval = pm2->ac.charger_connected;
 627                 break;
 628         case POWER_SUPPLY_PROP_VOLTAGE_AVG:
 629                 pm2->ac.cv_active = pm2xxx_charger_get_ac_cv(pm2);
 630                 val->intval = pm2->ac.cv_active;
 631                 break;
 632         default:
 633                 return -EINVAL;
 634         }
 635         return 0;
 636 }
 637
 638 static int pm2xxx_charging_init(struct pm2xxx_charger *pm2)
 639 {
 640         int ret = 0;
 641
 642         /* enable CC and CV watchdog */
 643         ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG3,
 644                 (PM2XXX_CH_WD_CV_PHASE_60MIN | PM2XXX_CH_WD_CC_PHASE_60MIN));
 645         if( ret < 0)
 646                 return ret;
 647
 648         /* enable precharge watchdog */
 649         ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG4,
 650                                         PM2XXX_CH_WD_PRECH_PHASE_60MIN);
 651
 652         /* Disable auto timeout */
 653         ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG5,
 654                                         PM2XXX_CH_WD_AUTO_TIMEOUT_20MIN);
 655
 656         /*
 657      * EOC current level = 100mA
 658          * Precharge current level = 100mA
 659          * CC current level = 1000mA
 660          */
 661         ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG6,
 662                 (PM2XXX_DIR_CH_CC_CURRENT_1000MA |
 663                 PM2XXX_CH_PRECH_CURRENT_100MA |
 664                 PM2XXX_CH_EOC_CURRENT_100MA));
 665
 666         /*
 667      * recharge threshold = 3.8V
 668          * Precharge to CC threshold = 2.9V
 669          */
 670         ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG7,
 671                 (PM2XXX_CH_PRECH_VOL_2_9 | PM2XXX_CH_VRESUME_VOL_3_8));
 672
 673         /* float voltage charger level = 4.2V */
 674         ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG8,
 675                 PM2XXX_CH_VOLT_4_2);
 676
 677         /* Voltage drop between VBAT and VSYS in HW charging = 300mV */
 678         ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG9,
 679                 (PM2XXX_CH_150MV_DROP_300MV | PM2XXX_CHARCHING_INFO_DIS |
 680                 PM2XXX_CH_CC_REDUCED_CURRENT_IDENT |
 681                 PM2XXX_CH_CC_MODEDROP_DIS));
 682
 683         /* Input charger level of over voltage = 10V */
 684         ret = pm2xxx_reg_write(pm2, PM2XXX_INP_VOLT_VPWR2,
 685                                         PM2XXX_VPWR2_OVV_10);
 686         ret = pm2xxx_reg_write(pm2, PM2XXX_INP_VOLT_VPWR1,
 687                                         PM2XXX_VPWR1_OVV_10);
 688
 689         /* Input charger drop */
 690         ret = pm2xxx_reg_write(pm2, PM2XXX_INP_DROP_VPWR2,
 691                 (PM2XXX_VPWR2_HW_OPT_DIS | PM2XXX_VPWR2_VALID_DIS |
 692                 PM2XXX_VPWR2_DROP_DIS));
 693         ret = pm2xxx_reg_write(pm2, PM2XXX_INP_DROP_VPWR1,
 694                 (PM2XXX_VPWR1_HW_OPT_DIS | PM2XXX_VPWR1_VALID_DIS |
 695                 PM2XXX_VPWR1_DROP_DIS));
 696
 697         /* Disable battery low monitoring */
 698         ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_LOW_LEV_COMP_REG,
 699                 PM2XXX_VBAT_LOW_MONITORING_ENA);
 700
 701         return ret;
 702 }
 703
 704 static int pm2xxx_charger_ac_en(struct ux500_charger *charger,
 705         int enable, int vset, int iset)
 706 {
 707         int ret;
 708         int volt_index;
 709         int curr_index;
 710         u8 val;
 711
 712         struct pm2xxx_charger *pm2 = to_pm2xxx_charger_ac_device_info(charger);
 713
 714         if (enable) {
 715                 if (!pm2->ac.charger_connected) {
 716                         dev_dbg(pm2->dev, "AC charger not connected\n");
 717                         return -ENXIO;
 718                 }
 719
 720                 dev_dbg(pm2->dev, "Enable AC: %dmV %dmA\n", vset, iset);
 721                 if (!pm2->vddadc_en_ac) {
 722                         ret = regulator_enable(pm2->regu);
 723                         if (ret)
 724                                 dev_warn(pm2->dev,
 725                                         "Failed to enable vddadc regulator\n");
 726                         else
 727                                 pm2->vddadc_en_ac = true;
 728                 }
 729
 730                 ret = pm2xxx_charging_init(pm2);
 731                 if (ret < 0) {
 732                         dev_err(pm2->dev, "%s charging init failed\n",
 733                                         __func__);
 734                         goto error_occured;
 735                 }
 736
 737                 volt_index = pm2xxx_voltage_to_regval(vset);
 738                 curr_index = pm2xxx_current_to_regval(iset);
 739
 740                 if (volt_index < 0 || curr_index < 0) {
 741                         dev_err(pm2->dev,
 742                                 "Charger voltage or current too high, "
 743                                 "charging not started\n");
 744                         return -ENXIO;
 745                 }
 746
 747                 ret = pm2xxx_reg_read(pm2, PM2XXX_BATT_CTRL_REG8, &val);
 748                 if (ret < 0) {
 749                         dev_err(pm2->dev, "%s pm2xxx read failed\n", __func__);
 750                         goto error_occured;
 751                 }
 752                 val &= ~PM2XXX_CH_VOLT_MASK;
 753                 val |= volt_index;
 754                 ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG8, val);
 755                 if (ret < 0) {
 756                         dev_err(pm2->dev, "%s pm2xxx write failed\n", __func__);
 757                         goto error_occured;
 758                 }
 759
 760                 ret = pm2xxx_reg_read(pm2, PM2XXX_BATT_CTRL_REG6, &val);
 761                 if (ret < 0) {
 762                         dev_err(pm2->dev, "%s pm2xxx read failed\n", __func__);
 763                         goto error_occured;
 764                 }
 765                 val &= ~PM2XXX_DIR_CH_CC_CURRENT_MASK;
 766                 val |= curr_index;
 767                 ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_CTRL_REG6, val);
 768                 if (ret < 0) {
 769                         dev_err(pm2->dev, "%s pm2xxx write failed\n", __func__);
 770                         goto error_occured;
 771                 }
 772
 773                 if (!pm2->bat->enable_overshoot) {
 774                         ret = pm2xxx_reg_read(pm2, PM2XXX_LED_CTRL_REG, &val);
 775                         if (ret < 0) {
 776                                 dev_err(pm2->dev, "%s pm2xxx read failed\n",
 777                                                                 __func__);
 778                                 goto error_occured;
 779                         }
 780                         val |= PM2XXX_ANTI_OVERSHOOT_EN;
 781                         ret = pm2xxx_reg_write(pm2, PM2XXX_LED_CTRL_REG, val);
 782                         if (ret < 0) {
 783                                 dev_err(pm2->dev, "%s pm2xxx write failed\n",
 784                                                                 __func__);
 785                                 goto error_occured;
 786                         }
 787                 }
 788
 789                 ret = pm2xxx_charging_enable_mngt(pm2);
 790                 if (ret < 0) {
 791                         dev_err(pm2->dev, "Failed to enable"
 792                                                 "pm2xxx ac charger\n");
 793                         goto error_occured;
 794                 }
 795
 796                 pm2->ac.charger_online = 1;
 797         } else {
 798                 pm2->ac.charger_online = 0;
 799                 pm2->ac.wd_expired = false;
 800
 801                 /* Disable regulator if enabled */
 802                 if (pm2->vddadc_en_ac) {
 803                         regulator_disable(pm2->regu);
 804                         pm2->vddadc_en_ac = false;
 805                 }
 806
 807                 ret = pm2xxx_charging_disable_mngt(pm2);
 808                 if (ret < 0) {
 809                         dev_err(pm2->dev, "failed to disable"
 810                                                 "pm2xxx ac charger\n");
 811                         goto error_occured;
 812                 }
 813
 814                 dev_dbg(pm2->dev, "PM2301: " "Disabled AC charging\n");
 815         }
 816         power_supply_changed(pm2->ac_chg.psy);
 817
 818 error_occured:
 819         return ret;
 820 }
 821
 822 static int pm2xxx_charger_watchdog_kick(struct ux500_charger *charger)
 823 {
 824         int ret;
 825         struct pm2xxx_charger *pm2;
 826
 827         if (charger->psy->desc->type == POWER_SUPPLY_TYPE_MAINS)
 828                 pm2 = to_pm2xxx_charger_ac_device_info(charger);
 829         else
 830                 return -ENXIO;
 831
 832         ret = pm2xxx_reg_write(pm2, PM2XXX_BATT_WD_KICK, WD_TIMER);
 833         if (ret)
 834                 dev_err(pm2->dev, "Failed to kick WD!\n");
 835
 836         return ret;
 837 }
 838
 839 static void pm2xxx_charger_ac_work(struct work_struct *work)
 840 {
 841         struct pm2xxx_charger *pm2 = container_of(work,
 842                 struct pm2xxx_charger, ac_work);
 843
 844
 845         power_supply_changed(pm2->ac_chg.psy);
 846         sysfs_notify(&pm2->ac_chg.psy->dev.kobj, NULL, "present");
 847 };
 848
 849 static void pm2xxx_charger_check_hw_failure_work(struct work_struct *work)
 850 {
 851         u8 reg_value;
 852
 853         struct pm2xxx_charger *pm2 = container_of(work,
 854                 struct pm2xxx_charger, check_hw_failure_work.work);
 855
 856         if (pm2->flags.ovv) {
 857                 pm2xxx_reg_read(pm2, PM2XXX_SRCE_REG_INT4, &reg_value);
 858
 859                 if (!(reg_value & (PM2XXX_INT4_S_ITVPWR1OVV |
 860                                         PM2XXX_INT4_S_ITVPWR2OVV))) {
 861                         pm2->flags.ovv = false;
 862                         power_supply_changed(pm2->ac_chg.psy);
 863                 }
 864         }
 865
 866         /* If we still have a failure, schedule a new check */
 867         if (pm2->flags.ovv) {
 868                 queue_delayed_work(pm2->charger_wq,
 869                         &pm2->check_hw_failure_work, round_jiffies(HZ));
 870         }
 871 }
 872
 873 static void pm2xxx_charger_check_main_thermal_prot_work(
 874         struct work_struct *work)
 875 {
 876         int ret;
 877         u8 val;
 878
 879         struct pm2xxx_charger *pm2 = container_of(work, struct pm2xxx_charger,
 880                                         check_main_thermal_prot_work);
 881
 882         /* Check if die temp warning is still active */
 883         ret = pm2xxx_reg_read(pm2, PM2XXX_SRCE_REG_INT5, &val);
 884         if (ret < 0) {
 885                 dev_err(pm2->dev, "%s pm2xxx read failed\n", __func__);
 886                 return;
 887         }
 888         if (val & (PM2XXX_INT5_S_ITTHERMALWARNINGRISE
 889                         | PM2XXX_INT5_S_ITTHERMALSHUTDOWNRISE))
 890                 pm2->flags.main_thermal_prot = true;
 891         else if (val & (PM2XXX_INT5_S_ITTHERMALWARNINGFALL
 892                                 | PM2XXX_INT5_S_ITTHERMALSHUTDOWNFALL))
 893                 pm2->flags.main_thermal_prot = false;
 894
 895         power_supply_changed(pm2->ac_chg.psy);
 896 }
 897
 898 static struct pm2xxx_interrupts pm2xxx_int = {
 899         .handler[0] = pm2_int_reg0,
 900         .handler[1] = pm2_int_reg1,
 901         .handler[2] = pm2_int_reg2,
 902         .handler[3] = pm2_int_reg3,
 903         .handler[4] = pm2_int_reg4,
 904         .handler[5] = pm2_int_reg5,
 905 };
 906
 907 static struct pm2xxx_irq pm2xxx_charger_irq[] = {
 908         {"PM2XXX_IRQ_INT", pm2xxx_irq_int},
 909 };
 910
 911 static int __maybe_unused pm2xxx_wall_charger_resume(struct device *dev)
 912 {
 913         struct i2c_client *i2c_client = to_i2c_client(dev);
 914         struct pm2xxx_charger *pm2;
 915
 916         pm2 =  (struct pm2xxx_charger *)i2c_get_clientdata(i2c_client);
 917         set_lpn_pin(pm2);
 918
 919         /* If we still have a HW failure, schedule a new check */
 920         if (pm2->flags.ovv)
 921                 queue_delayed_work(pm2->charger_wq,
 922                                 &pm2->check_hw_failure_work, 0);
 923
 924         return 0;
 925 }
 926
 927 static int __maybe_unused pm2xxx_wall_charger_suspend(struct device *dev)
 928 {
 929         struct i2c_client *i2c_client = to_i2c_client(dev);
 930         struct pm2xxx_charger *pm2;
 931
 932         pm2 =  (struct pm2xxx_charger *)i2c_get_clientdata(i2c_client);
 933         clear_lpn_pin(pm2);
 934
 935         /* Cancel any pending HW failure check */
 936         if (delayed_work_pending(&pm2->check_hw_failure_work))
 937                 cancel_delayed_work(&pm2->check_hw_failure_work);
 938
 939         flush_work(&pm2->ac_work);
 940         flush_work(&pm2->check_main_thermal_prot_work);
 941
 942         return 0;
 943 }
 944
 945 static int __maybe_unused pm2xxx_runtime_suspend(struct device *dev)
 946 {
 947         struct i2c_client *pm2xxx_i2c_client = to_i2c_client(dev);
 948         struct pm2xxx_charger *pm2;
 949
 950         pm2 = (struct pm2xxx_charger *)i2c_get_clientdata(pm2xxx_i2c_client);
 951         clear_lpn_pin(pm2);
 952
 953         return 0;
 954 }
 955
 956 static int __maybe_unused pm2xxx_runtime_resume(struct device *dev)
 957 {
 958         struct i2c_client *pm2xxx_i2c_client = to_i2c_client(dev);
 959         struct pm2xxx_charger *pm2;
 960
 961         pm2 = (struct pm2xxx_charger *)i2c_get_clientdata(pm2xxx_i2c_client);
 962
 963         if (gpio_is_valid(pm2->lpn_pin) && gpio_get_value(pm2->lpn_pin) == 0)
 964                 set_lpn_pin(pm2);
 965
 966         return 0;
 967 }
 968
 969 static const struct dev_pm_ops pm2xxx_pm_ops __maybe_unused = {
 970         SET_SYSTEM_SLEEP_PM_OPS(pm2xxx_wall_charger_suspend,
 971                 pm2xxx_wall_charger_resume)
 972         SET_RUNTIME_PM_OPS(pm2xxx_runtime_suspend, pm2xxx_runtime_resume, NULL)
 973 };
 974
 975 static int pm2xxx_wall_charger_probe(struct i2c_client *i2c_client,
 976                 const struct i2c_device_id *id)
 977 {
 978         struct pm2xxx_platform_data *pl_data = i2c_client->dev.platform_data;
 979         struct power_supply_config psy_cfg = {};
 980         struct pm2xxx_charger *pm2;
 981         int ret = 0;
 982         u8 val;
 983         int i;
 984
 985         if (!pl_data) {
 986                 dev_err(&i2c_client->dev, "No platform data supplied\n");
 987                 return -EINVAL;
 988         }
 989
 990         pm2 = kzalloc(sizeof(struct pm2xxx_charger), GFP_KERNEL);
 991         if (!pm2) {
 992                 dev_err(&i2c_client->dev, "pm2xxx_charger allocation failed\n");
 993                 return -ENOMEM;
 994         }
 995
 996         /* get parent data */
 997         pm2->dev = &i2c_client->dev;
 998
 999         pm2->pm2_int = &pm2xxx_int;
1000
1001         /* get charger spcific platform data */
1002         if (!pl_data->wall_charger) {
1003                 dev_err(pm2->dev, "no charger platform data supplied\n");
1004                 ret = -EINVAL;
1005                 goto free_device_info;
1006         }
1007
1008         pm2->pdata = pl_data->wall_charger;
1009
1010         /* get battery specific platform data */
1011         if (!pl_data->battery) {
1012                 dev_err(pm2->dev, "no battery platform data supplied\n");
1013                 ret = -EINVAL;
1014                 goto free_device_info;
1015         }
1016
1017         pm2->bat = pl_data->battery;
1018
1019         if (!i2c_check_functionality(i2c_client->adapter,
1020                         I2C_FUNC_SMBUS_BYTE_DATA |
1021                         I2C_FUNC_SMBUS_READ_WORD_DATA)) {
1022                 ret = -ENODEV;
1023                 dev_info(pm2->dev, "pm2301 i2c_check_functionality failed\n");
1024                 goto free_device_info;
1025         }
1026
1027         pm2->config.pm2xxx_i2c = i2c_client;
1028         pm2->config.pm2xxx_id = (struct i2c_device_id *) id;
1029         i2c_set_clientdata(i2c_client, pm2);
1030
1031         /* AC supply */
1032         /* power_supply base class */
1033         pm2->ac_chg_desc.name = pm2->pdata->label;
1034         pm2->ac_chg_desc.type = POWER_SUPPLY_TYPE_MAINS;
1035         pm2->ac_chg_desc.properties = pm2xxx_charger_ac_props;
1036         pm2->ac_chg_desc.num_properties = ARRAY_SIZE(pm2xxx_charger_ac_props);
1037         pm2->ac_chg_desc.get_property = pm2xxx_charger_ac_get_property;
1038
1039         psy_cfg.supplied_to = pm2->pdata->supplied_to;
1040         psy_cfg.num_supplicants = pm2->pdata->num_supplicants;
1041         /* pm2xxx_charger sub-class */
1042         pm2->ac_chg.ops.enable = &pm2xxx_charger_ac_en;
1043         pm2->ac_chg.ops.kick_wd = &pm2xxx_charger_watchdog_kick;
1044         pm2->ac_chg.ops.update_curr = &pm2xxx_charger_update_charger_current;
1045         pm2->ac_chg.max_out_volt = pm2xxx_charger_voltage_map[
1046                 ARRAY_SIZE(pm2xxx_charger_voltage_map) - 1];
1047         pm2->ac_chg.max_out_curr = pm2xxx_charger_current_map[
1048                 ARRAY_SIZE(pm2xxx_charger_current_map) - 1];
1049         pm2->ac_chg.wdt_refresh = WD_KICK_INTERVAL;
1050         pm2->ac_chg.enabled = true;
1051         pm2->ac_chg.external = true;
1052
1053         /* Create a work queue for the charger */
1054         pm2->charger_wq = alloc_ordered_workqueue("pm2xxx_charger_wq",
1055                                                   WQ_MEM_RECLAIM);
1056         if (pm2->charger_wq == NULL) {
1057                 ret = -ENOMEM;
1058                 dev_err(pm2->dev, "failed to create work queue\n");
1059                 goto free_device_info;
1060         }
1061
1062         /* Init work for charger detection */
1063         INIT_WORK(&pm2->ac_work, pm2xxx_charger_ac_work);
1064
1065         /* Init work for checking HW status */
1066         INIT_WORK(&pm2->check_main_thermal_prot_work,
1067                 pm2xxx_charger_check_main_thermal_prot_work);
1068
1069         /* Init work for HW failure check */
1070         INIT_DEFERRABLE_WORK(&pm2->check_hw_failure_work,
1071                 pm2xxx_charger_check_hw_failure_work);
1072
1073         /*
1074          * VDD ADC supply needs to be enabled from this driver when there
1075          * is a charger connected to avoid erroneous BTEMP_HIGH/LOW
1076          * interrupts during charging
1077          */
1078         pm2->regu = regulator_get(pm2->dev, "vddadc");
1079         if (IS_ERR(pm2->regu)) {
1080                 ret = PTR_ERR(pm2->regu);
1081                 dev_err(pm2->dev, "failed to get vddadc regulator\n");
1082                 goto free_charger_wq;
1083         }
1084
1085         /* Register AC charger class */
1086         pm2->ac_chg.psy = power_supply_register(pm2->dev, &pm2->ac_chg_desc,
1087                                                 &psy_cfg);
1088         if (IS_ERR(pm2->ac_chg.psy)) {
1089                 dev_err(pm2->dev, "failed to register AC charger\n");
1090                 ret = PTR_ERR(pm2->ac_chg.psy);
1091                 goto free_regulator;
1092         }
1093
1094         /* Register interrupts */
1095         ret = request_threaded_irq(gpio_to_irq(pm2->pdata->gpio_irq_number),
1096                                 NULL,
1097                                 pm2xxx_charger_irq[0].isr,
1098                                 pm2->pdata->irq_type,
1099                                 pm2xxx_charger_irq[0].name, pm2);
1100
1101         if (ret != 0) {
1102                 dev_err(pm2->dev, "failed to request %s IRQ %d: %d\n",
1103                 pm2xxx_charger_irq[0].name,
1104                         gpio_to_irq(pm2->pdata->gpio_irq_number), ret);
1105                 goto unregister_pm2xxx_charger;
1106         }
1107
1108         ret = pm_runtime_set_active(pm2->dev);
1109         if (ret)
1110                 dev_err(pm2->dev, "set active Error\n");
1111
1112         pm_runtime_enable(pm2->dev);
1113         pm_runtime_set_autosuspend_delay(pm2->dev, PM2XXX_AUTOSUSPEND_DELAY);
1114         pm_runtime_use_autosuspend(pm2->dev);
1115         pm_runtime_resume(pm2->dev);
1116
1117         /* pm interrupt can wake up system */
1118         ret = enable_irq_wake(gpio_to_irq(pm2->pdata->gpio_irq_number));
1119         if (ret) {
1120                 dev_err(pm2->dev, "failed to set irq wake\n");
1121                 goto unregister_pm2xxx_interrupt;
1122         }
1123
1124         mutex_init(&pm2->lock);
1125
1126         if (gpio_is_valid(pm2->pdata->lpn_gpio)) {
1127                 /* get lpn GPIO from platform data */
1128                 pm2->lpn_pin = pm2->pdata->lpn_gpio;
1129
1130                 /*
1131                  * Charger detection mechanism requires pulling up the LPN pin
1132                  * while i2c communication if Charger is not connected
1133                  * LPN pin of PM2301 is GPIO60 of AB9540
1134                  */
1135                 ret = gpio_request(pm2->lpn_pin, "pm2301_lpm_gpio");
1136
1137                 if (ret < 0) {
1138                         dev_err(pm2->dev, "pm2301_lpm_gpio request failed\n");
1139                         goto disable_pm2_irq_wake;
1140                 }
1141                 ret = gpio_direction_output(pm2->lpn_pin, 0);
1142                 if (ret < 0) {
1143                         dev_err(pm2->dev, "pm2301_lpm_gpio direction failed\n");
1144                         goto free_gpio;
1145                 }
1146                 set_lpn_pin(pm2);
1147         }
1148
1149         /* read  interrupt registers */
1150         for (i = 0; i < PM2XXX_NUM_INT_REG; i++)
1151                 pm2xxx_reg_read(pm2,
1152                         pm2xxx_interrupt_registers[i],
1153                         &val);
1154
1155         ret = pm2xxx_charger_detection(pm2, &val);
1156
1157         if ((ret == 0) && val) {
1158                 pm2->ac.charger_connected = 1;
1159                 ab8500_override_turn_on_stat(~AB8500_POW_KEY_1_ON,
1160                                              AB8500_MAIN_CH_DET);
1161                 pm2->ac_conn = true;
1162                 power_supply_changed(pm2->ac_chg.psy);
1163                 sysfs_notify(&pm2->ac_chg.psy->dev.kobj, NULL, "present");
1164         }
1165
1166         return 0;
1167
1168 free_gpio:
1169         if (gpio_is_valid(pm2->lpn_pin))
1170                 gpio_free(pm2->lpn_pin);
1171 disable_pm2_irq_wake:
1172         disable_irq_wake(gpio_to_irq(pm2->pdata->gpio_irq_number));
1173 unregister_pm2xxx_interrupt:
1174         /* disable interrupt */
1175         free_irq(gpio_to_irq(pm2->pdata->gpio_irq_number), pm2);
1176 unregister_pm2xxx_charger:
1177         /* unregister power supply */
1178         power_supply_unregister(pm2->ac_chg.psy);
1179 free_regulator:
1180         /* disable the regulator */
1181         regulator_put(pm2->regu);
1182 free_charger_wq:
1183         destroy_workqueue(pm2->charger_wq);
1184 free_device_info:
1185         kfree(pm2);
1186
1187         return ret;
1188 }
1189
1190 static int pm2xxx_wall_charger_remove(struct i2c_client *i2c_client)
1191 {
1192         struct pm2xxx_charger *pm2 = i2c_get_clientdata(i2c_client);
1193
1194         /* Disable pm_runtime */
1195         pm_runtime_disable(pm2->dev);
1196         /* Disable AC charging */
1197         pm2xxx_charger_ac_en(&pm2->ac_chg, false, 0, 0);
1198
1199         /* Disable wake by pm interrupt */
1200         disable_irq_wake(gpio_to_irq(pm2->pdata->gpio_irq_number));
1201
1202         /* Disable interrupts */
1203         free_irq(gpio_to_irq(pm2->pdata->gpio_irq_number), pm2);
1204
1205         /* Delete the work queue */
1206         destroy_workqueue(pm2->charger_wq);
1207
1208         flush_scheduled_work();
1209
1210         /* disable the regulator */
1211         regulator_put(pm2->regu);
1212
1213         power_supply_unregister(pm2->ac_chg.psy);
1214
1215         if (gpio_is_valid(pm2->lpn_pin))
1216                 gpio_free(pm2->lpn_pin);
1217
1218         kfree(pm2);
1219
1220         return 0;
1221 }
1222
1223 static const struct i2c_device_id pm2xxx_id[] = {
1224         { "pm2301", 0 },
1225         { }
1226 };
1227
1228 MODULE_DEVICE_TABLE(i2c, pm2xxx_id);
1229
1230 static struct i2c_driver pm2xxx_charger_driver = {
1231         .probe = pm2xxx_wall_charger_probe,
1232         .remove = pm2xxx_wall_charger_remove,
1233         .driver = {
1234                 .name = "pm2xxx-wall_charger",
1235                 .pm = IS_ENABLED(CONFIG_PM) ? &pm2xxx_pm_ops : NULL,
1236         },
1237         .id_table = pm2xxx_id,
1238 };
1239
1240 static int __init pm2xxx_charger_init(void)
1241 {
1242         return i2c_add_driver(&pm2xxx_charger_driver);
1243 }
1244
1245 static void __exit pm2xxx_charger_exit(void)
1246 {
1247         i2c_del_driver(&pm2xxx_charger_driver);
1248 }
1249
1250 device_initcall_sync(pm2xxx_charger_init);
1251 module_exit(pm2xxx_charger_exit);
1252
1253 MODULE_LICENSE("GPL v2");
1254 MODULE_AUTHOR("Rajkumar kasirajan, Olivier Launay");
1255 MODULE_DESCRIPTION("PM2xxx charger management driver");