arch/arm/boot/dts/qcom/qcom-msm8974pro-oneplus-bacon.dts

   1 // SPDX-License-Identifier: GPL-2.0
   2 #include "qcom-msm8974pro.dtsi"
   3 #include "qcom-pm8841.dtsi"
   4 #include "qcom-pm8941.dtsi"
   5 #include <dt-bindings/input/input.h>
   6 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
   7
   8 / {
   9         model = "OnePlus One";
  10         compatible = "oneplus,bacon", "qcom,msm8974pro", "qcom,msm8974";
  11         chassis-type = "handset";
  12         qcom,msm-id = <194 0x10000>;
  13         qcom,board-id = <8 0>;
  14
  15         aliases {
  16                 serial0 = &blsp1_uart2;
  17         };
  18
  19         chosen {
  20                 stdout-path = "serial0:115200n8";
  21         };
  22
  23         gpio-keys {
  24                 compatible = "gpio-keys";
  25
  26                 pinctrl-0 = <&gpio_keys_default>, <&gpio_hall_sensor_default>;
  27                 pinctrl-names = "default";
  28
  29                 key-volume-down {
  30                         label = "Volume Down";
  31                         gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
  32                         linux,code = <KEY_VOLUMEDOWN>;
  33                         wakeup-source;
  34                         debounce-interval = <15>;
  35                 };
  36
  37                 key-volume-up {
  38                         label = "Volume Up";
  39                         gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>;
  40                         linux,code = <KEY_VOLUMEUP>;
  41                         wakeup-source;
  42                         debounce-interval = <15>;
  43                 };
  44
  45                 event-hall-sensor {
  46                         label = "Hall Effect Sensor";
  47                         gpios = <&tlmm 68 GPIO_ACTIVE_LOW>;
  48                         linux,input-type = <EV_SW>;
  49                         linux,code = <SW_LID>;
  50                         linux,can-disable;
  51                         debounce-interval = <150>;
  52                 };
  53         };
  54 };
  55
  56 &blsp1_i2c1 {
  57         status = "okay";
  58
  59         fuel-gauge@55 {
  60                 compatible = "ti,bq27541";
  61                 reg = <0x55>;
  62                 power-supplies = <&bq24196_charger>;
  63         };
  64 };
  65
  66 &blsp1_i2c2 {
  67         status = "okay";
  68
  69         rmi4-i2c-dev@20 {
  70                 compatible = "syna,rmi4-i2c";
  71                 reg = <0x20>;
  72
  73                 syna,startup-delay-ms = <100>;
  74
  75                 interrupts-extended = <&tlmm 61 IRQ_TYPE_EDGE_FALLING>;
  76                 vdd-supply = <&pm8941_l22>;
  77                 vio-supply = <&pm8941_lvs3>;
  78
  79                 pinctrl-names = "default";
  80                 pinctrl-0 = <&touch_default_state>;
  81
  82                 #address-cells = <1>;
  83                 #size-cells = <0>;
  84
  85                 rmi4-f01@1 {
  86                         reg = <0x1>;
  87                         syna,nosleep-mode = <1>;
  88                 };
  89
  90                 rmi4-f12@12 {
  91                         reg = <0x12>;
  92                         syna,sensor-type = <1>;
  93                         /*
  94                          * Touchscreen size is 2040x1080, y-values between
  95                          * 1920-2040 are used for touchkey (menu, home & back).
  96                          * For now clip it off so we don't get touch events
  97                          * outside of the display area.
  98                          */
  99                         syna,clip-y-high = <1920>;
 100                 };
 101         };
 102
 103         led-controller@36 {
 104                 compatible = "ti,lm3630a";
 105                 reg = <0x36>;
 106
 107                 #address-cells = <1>;
 108                 #size-cells = <0>;
 109
 110                 led@0 {
 111                         reg = <0>;
 112                         led-sources = <0 1>;
 113                         label = "lcd-backlight";
 114                         default-brightness = <80>;
 115                 };
 116         };
 117
 118         led-controller@68 {
 119                 compatible = "si-en,sn3193";
 120                 reg = <0x68>;
 121
 122                 shutdown-gpios = <&tlmm 45 GPIO_ACTIVE_HIGH>;
 123
 124                 #address-cells = <1>;
 125                 #size-cells = <0>;
 126
 127                 led@1 {
 128                         reg = <1>;
 129                         label = "red:status";
 130                         led-max-microamp = <17500>;
 131                 };
 132
 133                 led@2 {
 134                         reg = <2>;
 135                         label = "green:status";
 136                         led-max-microamp = <17500>;
 137                 };
 138
 139                 led@3 {
 140                         reg = <3>;
 141                         label = "blue:status";
 142                         led-max-microamp = <17500>;
 143                 };
 144         };
 145 };
 146
 147 &blsp1_i2c6 {
 148         status = "okay";
 149
 150         bq24196_charger: charger@6b {
 151                 compatible = "ti,bq24196";
 152                 reg = <0x6b>;
 153                 interrupts-extended = <&tlmm 31 IRQ_TYPE_EDGE_FALLING>;
 154                 omit-battery-class;
 155         };
 156 };
 157
 158 &blsp1_uart2 {
 159         status = "okay";
 160 };
 161
 162 &gcc {
 163         compatible = "qcom,gcc-msm8974pro-ac";
 164 };
 165
 166 &pm8941_coincell {
 167         qcom,rset-ohms = <800>;
 168         qcom,vset-millivolts = <3200>;
 169
 170         status = "okay";
 171 };
 172
 173 &pm8941_gpios {
 174         gpio_keys_default: gpio-keys-active-state {
 175                 pins = "gpio2", "gpio5";
 176                 function = "normal";
 177                 input-enable;
 178                 bias-disable;
 179                 power-source = <PM8941_GPIO_S3>;
 180         };
 181 };
 182
 183 &pm8941_vib {
 184         status = "okay";
 185 };
 186
 187 &pronto {
 188         vddmx-supply = <&pm8841_s1>;
 189         vddcx-supply = <&pm8841_s2>;
 190         vddpx-supply = <&pm8941_s3>;
 191
 192         pinctrl-names = "default";
 193         pinctrl-0 = <&wcnss_pin_a>;
 194
 195         status = "okay";
 196
 197         iris {
 198                 vddxo-supply = <&pm8941_l6>;
 199                 vddrfa-supply = <&pm8941_l11>;
 200                 vddpa-supply = <&pm8941_l19>;
 201                 vdddig-supply = <&pm8941_s3>;
 202         };
 203
 204         smd-edge {
 205                 qcom,remote-pid = <4>;
 206                 label = "pronto";
 207
 208                 wcnss {
 209                         status = "okay";
 210                 };
 211         };
 212 };
 213
 214 &remoteproc_adsp {
 215         cx-supply = <&pm8841_s2>;
 216
 217         status = "okay";
 218 };
 219
 220 &rpm_requests {
 221         regulators-0 {
 222                 compatible = "qcom,rpm-pm8841-regulators";
 223
 224                 pm8841_s1: s1 {
 225                         regulator-min-microvolt = <675000>;
 226                         regulator-max-microvolt = <1050000>;
 227                 };
 228
 229                 pm8841_s2: s2 {
 230                         regulator-min-microvolt = <875000>;
 231                         regulator-max-microvolt = <1050000>;
 232                         regulator-always-on;
 233                 };
 234
 235                 pm8841_s3: s3 {
 236                         regulator-min-microvolt = <1050000>;
 237                         regulator-max-microvolt = <1050000>;
 238                 };
 239         };
 240
 241         regulators-1 {
 242                 compatible = "qcom,rpm-pm8941-regulators";
 243
 244                 vdd_l1_l3-supply = <&pm8941_s1>;
 245                 vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
 246                 vdd_l4_l11-supply = <&pm8941_s1>;
 247                 vdd_l5_l7-supply = <&pm8941_s2>;
 248                 vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
 249                 vdd_l8_l16_l18_l19-supply = <&vreg_vph_pwr>;
 250                 vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
 251                 vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
 252                 vdd_l21-supply = <&vreg_boost>;
 253
 254                 pm8941_s1: s1 {
 255                         regulator-min-microvolt = <1300000>;
 256                         regulator-max-microvolt = <1300000>;
 257
 258                         regulator-always-on;
 259                         regulator-boot-on;
 260                 };
 261
 262                 pm8941_s2: s2 {
 263                         regulator-min-microvolt = <2150000>;
 264                         regulator-max-microvolt = <2150000>;
 265
 266                         regulator-boot-on;
 267                 };
 268
 269                 pm8941_s3: s3 {
 270                         regulator-min-microvolt = <1800000>;
 271                         regulator-max-microvolt = <1800000>;
 272                         regulator-system-load = <154000>;
 273
 274                         regulator-always-on;
 275                         regulator-boot-on;
 276                         regulator-allow-set-load;
 277                 };
 278
 279                 pm8941_l1: l1 {
 280                         regulator-min-microvolt = <1225000>;
 281                         regulator-max-microvolt = <1225000>;
 282
 283                         regulator-always-on;
 284                         regulator-boot-on;
 285                 };
 286
 287                 pm8941_l2: l2 {
 288                         regulator-min-microvolt = <1200000>;
 289                         regulator-max-microvolt = <1200000>;
 290                 };
 291
 292                 pm8941_l3: l3 {
 293                         regulator-min-microvolt = <1225000>;
 294                         regulator-max-microvolt = <1225000>;
 295                 };
 296
 297                 pm8941_l4: l4 {
 298                         regulator-min-microvolt = <1225000>;
 299                         regulator-max-microvolt = <1225000>;
 300                 };
 301
 302                 pm8941_l5: l5 {
 303                         regulator-min-microvolt = <1800000>;
 304                         regulator-max-microvolt = <1800000>;
 305                 };
 306
 307                 pm8941_l6: l6 {
 308                         regulator-min-microvolt = <1800000>;
 309                         regulator-max-microvolt = <1800000>;
 310
 311                         regulator-boot-on;
 312                 };
 313
 314                 pm8941_l7: l7 {
 315                         regulator-min-microvolt = <1800000>;
 316                         regulator-max-microvolt = <1800000>;
 317
 318                         regulator-boot-on;
 319                 };
 320
 321                 pm8941_l8: l8 {
 322                         regulator-min-microvolt = <1800000>;
 323                         regulator-max-microvolt = <1800000>;
 324                 };
 325
 326                 pm8941_l9: l9 {
 327                         regulator-min-microvolt = <1800000>;
 328                         regulator-max-microvolt = <2950000>;
 329                 };
 330
 331                 pm8941_l10: l10 {
 332                         regulator-min-microvolt = <1800000>;
 333                         regulator-max-microvolt = <2950000>;
 334                 };
 335
 336                 pm8941_l11: l11 {
 337                         regulator-min-microvolt = <1225000>;
 338                         regulator-max-microvolt = <1350000>;
 339                 };
 340
 341                 pm8941_l12: l12 {
 342                         regulator-min-microvolt = <1800000>;
 343                         regulator-max-microvolt = <1800000>;
 344
 345                         regulator-always-on;
 346                         regulator-boot-on;
 347                         regulator-allow-set-load;
 348                 };
 349
 350                 pm8941_l13: l13 {
 351                         regulator-min-microvolt = <1800000>;
 352                         regulator-max-microvolt = <2950000>;
 353
 354                         regulator-boot-on;
 355                 };
 356
 357                 pm8941_l14: l14 {
 358                         regulator-min-microvolt = <1800000>;
 359                         regulator-max-microvolt = <1800000>;
 360                 };
 361
 362                 pm8941_l15: l15 {
 363                         regulator-min-microvolt = <2050000>;
 364                         regulator-max-microvolt = <2050000>;
 365                 };
 366
 367                 pm8941_l16: l16 {
 368                         regulator-min-microvolt = <2700000>;
 369                         regulator-max-microvolt = <2700000>;
 370                 };
 371
 372                 pm8941_l17: l17 {
 373                         regulator-min-microvolt = <2850000>;
 374                         regulator-max-microvolt = <2850000>;
 375                 };
 376
 377                 pm8941_l18: l18 {
 378                         regulator-min-microvolt = <2850000>;
 379                         regulator-max-microvolt = <2850000>;
 380                 };
 381
 382                 pm8941_l19: l19 {
 383                         regulator-min-microvolt = <2900000>;
 384                         regulator-max-microvolt = <3350000>;
 385                 };
 386
 387                 pm8941_l20: l20 {
 388                         regulator-min-microvolt = <2950000>;
 389                         regulator-max-microvolt = <2950000>;
 390
 391                         regulator-system-load = <200000>;
 392                         regulator-allow-set-load;
 393                         regulator-boot-on;
 394                 };
 395
 396                 pm8941_l21: l21 {
 397                         regulator-min-microvolt = <2950000>;
 398                         regulator-max-microvolt = <2950000>;
 399
 400                         regulator-boot-on;
 401                 };
 402
 403                 pm8941_l22: l22 {
 404                         regulator-min-microvolt = <3000000>;
 405                         regulator-max-microvolt = <3000000>;
 406                         regulator-allow-set-load;
 407                 };
 408
 409                 pm8941_l23: l23 {
 410                         regulator-min-microvolt = <3000000>;
 411                         regulator-max-microvolt = <3000000>;
 412                 };
 413
 414                 pm8941_l24: l24 {
 415                         regulator-min-microvolt = <3075000>;
 416                         regulator-max-microvolt = <3075000>;
 417
 418                         regulator-boot-on;
 419                 };
 420
 421                 pm8941_lvs3: lvs3 {};
 422         };
 423 };
 424
 425 &sdhc_1 {
 426         vmmc-supply = <&pm8941_l20>;
 427         vqmmc-supply = <&pm8941_s3>;
 428
 429         pinctrl-names = "default", "sleep";
 430         pinctrl-0 = <&sdc1_on>;
 431         pinctrl-1 = <&sdc1_off>;
 432
 433         status = "okay";
 434 };
 435
 436 &tlmm {
 437         gpio_hall_sensor_default: gpio-hall-sensor-default-state {
 438                 pins = "gpio68";
 439                 function = "gpio";
 440                 drive-strength = <8>;
 441                 bias-pull-up;
 442         };
 443
 444         sdc1_on: sdc1-on-state {
 445                 clk-pins {
 446                         pins = "sdc1_clk";
 447                         drive-strength = <4>;
 448                         bias-disable;
 449                 };
 450
 451                 cmd-data-pins {
 452                         pins = "sdc1_cmd", "sdc1_data";
 453                         drive-strength = <4>;
 454                         bias-pull-up;
 455                 };
 456         };
 457
 458         touch_default_state: touch-default-state {
 459                 int-pins {
 460                         pins = "gpio61";
 461                         function = "gpio";
 462                         drive-strength = <2>;
 463                         bias-disable;
 464                 };
 465
 466                 reset-pins {
 467                         pins = "gpio60";
 468                         function = "gpio";
 469                         drive-strength = <2>;
 470                         bias-pull-up;
 471                 };
 472         };
 473
 474         wcnss_pin_a: wcnss-pin-active-state {
 475                 wlan-pins {
 476                         pins = "gpio36", "gpio37", "gpio38", "gpio39", "gpio40";
 477                         function = "wlan";
 478                         drive-strength = <6>;
 479                         bias-pull-down;
 480                 };
 481
 482                 bt-pins {
 483                         pins = "gpio35", "gpio43", "gpio44";
 484                         function = "bt";
 485                         drive-strength = <2>;
 486                         bias-pull-down;
 487                 };
 488         };
 489 };
 490
 491 &usb {
 492         phys = <&usb_hs1_phy>;
 493         phy-select = <&tcsr 0xb000 0>;
 494         extcon = <&smbb>, <&usb_id>;
 495         vbus-supply = <&chg_otg>;
 496
 497         hnp-disable;
 498         srp-disable;
 499         adp-disable;
 500
 501         status = "okay";
 502 };
 503
 504 &usb_hs1_phy {
 505         status = "okay";
 506
 507         v1p8-supply = <&pm8941_l6>;
 508         v3p3-supply = <&pm8941_l24>;
 509
 510         extcon = <&smbb>;
 511         qcom,init-seq = /bits/ 8 <0x1 0x64>;
 512 };