git.samba.org - sfrench/cifs-2.6.git/log

Merge tag 'spi-bpw-is-supported' of https://git./linux/kernel/git/broonie/spi into spi-5.3

spi: Add spi_is_bpw_supported()

Lets client drivers check and potentially handle issues.

spi: rockchip: turn down tx dma bursts

This fixes tx and bi-directional dma transfers on rk3399-gru-kevin.

It seems the SPI fifo must have room for 2 bursts when the dma_tx_req
signal is generated or it might skip some words. This in turn makes
the rx dma channel never complete for bi-directional transfers.

Fix it by setting tx burst length to fifo_len / 4 and the dma
watermark to fifo_len / 2.

However the rk3399 TRM says (sic):
"DMAC support incrementing-address burst and fixed-address burst. But in
the case of access SPI and UART at byte or halfword size, DMAC only
support fixed-address burst and the address must be aligned to word."

So this relies on fifo_len being a multiple of 16 such that the
burst length (= fifo_len / 4) is a multiple of 4 and the addresses
will be word-aligned.

Fixes: dcfc861d24ec ("spi: rockchip: adjust dma watermark and burstlen")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: core: allow defining time that cs is deasserted as a multiple of SCK

Support setting a delay between cs assert and deassert as
a multiple of spi clock length.

Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: core: allow defining time that cs is deasserted

For some SPI devices that support speed_hz > 1MHz the default 10 us delay
when cs_change = 1 is typically way to long and may result in poor spi bus
utilization.

This patch makes it possible to control the delay at micro or nano second
resolution on a per spi_transfer basis. It even allows an "as fast as
possible" mode with:
xfer.cs_change_delay_unit = SPI_DELAY_UNIT_NSECS;
xfer.cs_change_delay = 0;

The delay code is shared between delay_usecs and cs_change_delay for
consistency and reuse, so in the future this change_delay_unit could also
apply to delay_usec as well.

Note that on slower SOCs/CPU actually reaching ns deasserts on cs is not
realistic as the gpio overhead alone (without any delays added ) may
already leave cs deasserted for more than 1us - at least on a raspberry pi.
But at the very least this way we can keep it as short as possible.

Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: bcm2835: add driver stats to debugfs

To estimate efficiency add statistics on transfer types
(polling, interrupt and dma) used to debugfs.

Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Changelog:
  V1 -> V2: applied feedback by Stefan Wahren
            reorganized patchset
    added extra rational, descriptions
    fixed compile issue when CONFIG_DEBUG_FS is unset
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: bcm2835: make the polling duration limits configurable

Under some circumstances the default 30 us polling limit is not optimal
and may lead to long delays because we are waiting on an interrupt.
with this patch we have the possibility to influence this policy.

So make this limit (in us) configurable via a module parameters
(but also modifyable via /sys/modules/...)

This replicates similar code found in spi-bcm2835aux.

Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Changelog:
  V1 -> V2: applied feedback by Stefan Wahren
            reorganized patchset
    added extra rational, descriptions
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: bcm2835: added comment about different bus behaviour of DMA mode

The DMA mode behaves slightly different than polling or interrupt driven
mode, so just document the fact

Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Changelog:
V1 -> V2: applied feedback by Stefan Wahren
new in V2
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: bcm2835: Avoid 64-bit arithmetic in xfer len calc

Avoid 64 bit aritmetics when deciding if we need to use polling or not
This replicates: commit d704afffe65c
("spi: bcm2835aux: Avoid 64-bit arithmetic in xfer len calc")
from spi-bcm2835aux

Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Changelog:
  V1 -> V2: applied feedback by Stefan Wahren
            reorganized patchset
    added extra rational, descriptions
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: bcm2835: bcm2835_spi_transfer_one_poll remove unnecessary argument

Remove the unnecessary argument of xfer_time_us when calling
bcm2835_spi_transfer_one_poll.

Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Changelog:
  V1 -> V2: applied feedback by Stefan Wahren
            reorganized patchset
    added extra rational, descriptions
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: at91-usart: add DMA support

This patch adds support for DMA. Transfers are done with dma only if
they are longer than 16 bytes in order to achieve a better performance.
DMA setup introduces a little overhead and for transfers shorter than 16
bytes there is no performance improvement.

Signed-off-by: Radu Pirea <radu_nicolae.pirea@upb.ro>
Signed-off-by: Mark Brown <broonie@kernel.org>

dt-bindings: mfd: atmel-usart: add DMA bindings for USART in SPI mode

The bindings for DMA are now common for both drivers of the USART
IP.

The node given as an example for USART in SPI mode has been updated in
order to include DMA bindings.

Signed-off-by: Radu Pirea <radu_nicolae.pirea@upb.ro>
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: ep93xx: Drop unused variable

My previous patch leaves a dangling variable in the driver.
get rid of it.

Fixes: 06a391b1621e ("spi: ep93xx: Convert to use CS GPIO descriptors")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Merge branch 'spi-5.2' into spi-next

Merge branch 'spi-5.1' into spi-linus

spi: rspi: Fix handling of QSPI code when transmit and receive

Process handling QSPI when transmit/receive at qspi_trigger_transfer_out_in() as follows:
Setting the trigger, is the number of bytes in the FIFO buffer to determine
when there is an interrupt. Then check if the value of triggering number is
32-bytes or 1-byte, there will be corresponding processing
Handling (if (n == QSPI_BUFFER_SIZE) esle) this is unnecessary, leads to the
same processing of data transmission or reception, The difference here are with
ret = rspi_wait_for_tx_empty(rspi);
ret = rspi_wait_for_rx_full(rspi);

When the nummber trigger is 32 bytes, we only write into FIFO when the FIFO is completely empty
(interrupt transmission), and only receive if FIFO is full of 32 bytes of data.

In the case of a nummber trigger that is 1 byte, in principle we still need to process
rspi_wait_for_tx_empty/full so that FIFO is empty only with the amount of data we need to write to
or equal to the number of bytes we need to receive, There is currently no processing of this.
And in the current case with this patch, at this time it only needs at least 1 byte received in
FIFO that has interrupt received, or FIFO at least 1bytes free can be written into FIFO,
This patch therefore does not affect this processing.
So we need to eliminate unnecessary waste processing (if (n == QSPI_BUFFER_SIZE) esle),
more precisely in waiting for FIFO status.
The same with handling in qspi_transfer_out()/qspi_transfer_in().

Signed-off-by: Hoan Nguyen An <na-hoan@jinso.co.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: atmel-quadspi: fix crash while suspending

atmel_qspi objects are kept in spi_controller objects, so, first get
pointer to spi_controller object and then get atmel_qspi object from
spi_controller object.

Fixes: 2d30ac5ed633 ("mtd: spi-nor: atmel-quadspi: Use spi-mem interface for atmel-quadspi driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: stm32: return the get_irq error

During probe, return the "get_irq" error value instead of -ENOENT. This
allows the driver to be defer probed if needed.

Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Acked-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: tegra114: fix PIO transfer

This patch fixes PIO mode transfer to use PIO bit in SPI_COMMAND1 register.
Current driver uses DMA_EN instead of PIO bit.

Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: pxa2xx: fix SCR (divisor) calculation

Calculate the divisor for the SCR (Serial Clock Rate), avoiding
that the SSP transmission rate can be greater than the device rate.

When the division between the SSP clock and the device rate generates
a reminder, we have to increment by one the divisor.
In this way the resulting SSP clock will never be greater than the
device SPI max frequency.

For example, with:

- ssp_clk = 50 MHz
- dev freq = 15 MHz

without this patch the SSP clock will be greater than 15 MHz:

- 25 MHz for PXA25x_SSP and CE4100_SSP
- 16,56 MHz for the others

Instead, with this patch, we have in both case an SSP clock of 12.5MHz,
so the max rate of the SPI device clock is respected.

Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: Clear SPI_CS_HIGH flag from bad_bits for GPIO chip-select

When GPIO chip-select is used nothing prevents any available SPI
controllers to work with both CS-high and traditional CS-low modes.
In fact the SPI bus core code already does it, so we don't need to
introduce any modification there. But spi_setup() still fails to
switch the interface settings if CS-high flag is set for the case
of GPIO-driven slave chip-select when the SPI controller doesn't
support the hardwired CS-inversion. Lets fix it by clearing the
SPI_CS_HIGH flag out from bad_bits (unsupported by controller) when
client chip is selected by GPIO.

This feature is useful for slave devices, which in accordance with
communication protocol can work with both active-high and active-low
chip-selects. I am aware of one such device. It is MMC-SPI interface,
when at init sequence the driver needs to perform a read operation with
low and high chip-select sequentially (requirement of 74 clock cycles
with both chipselect, see the mmc_spi driver for details).

Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: ep93xx: Convert to use CS GPIO descriptors

This converts the EP93xx SPI master driver to use GPIO
descriptors for chip select handling.

EP93xx was using platform data to pass in GPIO lines,
by converting all board files to use GPIO descriptor
tables the core will look up the GPIO lines from the
SPI device in the same manner as for device tree.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: AD ASoC: declare missing of table

Add missing <of_device_id> table for SPI driver relying on SPI
device match since compatible is in a DT binding or in a DTS.

Before this patch:
modinfo sound/soc/codecs/snd-soc-adau1977-spi.ko | grep alias
alias:          spi:adau1979
alias:          spi:adau1978
alias:          spi:adau1977

After this patch:
modinfo sound/soc/codecs/snd-soc-adau1977-spi.ko | grep alias
alias:          of:N*T*Cadi,adau1979C*
alias:          of:N*T*Cadi,adau1979
alias:          of:N*T*Cadi,adau1978C*
alias:          of:N*T*Cadi,adau1978
alias:          of:N*T*Cadi,adau1977C*
alias:          of:N*T*Cadi,adau1977
alias:          spi:adau1979
alias:          spi:adau1978
alias:          spi:adau1977

Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Daniel Gomez <dagmcr@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: spi-mem: zynq-qspi: Fix build error on architectures missing readsl/writesl

Alpha and some of the architectures are missing readsl/writesl functions.
so the zynq-qspi driver won't be able to build on these arches. hence use
ioread32_rep()/iowrite32_rep() instead of readsl()/writesl().

Signed-off-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: stm32-qspi: manage the get_irq error case

During probe, check the "get_irq" error value.

Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Acked-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

spi/spi-bcm2835: Split transfers that exceed DLEN

Split spi transfers into chunks of <=65532 to enable the driver to
perform DMA transfer on big buffers. The DLEN register specifies the
number of bytes to transfer in DMA mode. It is 16-bit wide and thus the
maximum DMA transfer is 65535 bytes. Set the maximum to 65532 (4 byte
aligned) since the FIFO in DMA mode is accessed in 4 byte chunks.

->max_dma_len is the value the spi core uses when splitting the buffer
into scatter gather entries.
The BCM2835 DMA block has 2 types of channels/engines:
- Normal: Max length: 1G
- Lite: Max length: 65535

Even when using a Lite channel we will not exceed the max length, so
let's drop setting ->max_dma_len.

Signed-off-by: Meghana Madhyastha <meghana.madhyastha@gmail.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: expand mode support

This patch changes mode and mode_bits from u16 to u32 to allow more
mode configurations.

Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

dt-bindings: spi: spi-mt65xx: add support for MT8516

Add binding documentation of spi-mt65xx for MT8516 SOC.

Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: pxa2xx: Add support for Intel Comet Lake

Add PCI IDs for SPI on Comet Lake.

Signed-off-by: Evan Green <evgreen@chromium.org>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

spi/trace: Cap buffer contents at 64 bytes

Large transfers (64kB) doesn't show up in the trace. Not sure why, but
since printk can only display buffers up to 64 bytes in length, we only
need to store the first 64 bytes.

Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: Release spi_res after finalizing message

spi_split_transfers_maxsize() can be used to split a transfer. This
function uses spi_res to lifetime manage the added transfer structures.
So in order to finalize the current message while it contains the split
transfers, spi_res_release() must be called after finalizing.

Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: Remove warning in spi_split_transfers_maxsize()

Don't warn about splitting transfers, the info is available in the
statistics if needed.

Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: Remove one needless transfer speed fall back case

Falling back to maximum speed of the controller in case of SPI slave
maximum speed is not set is needless. It already defaults to maximum
speed of the controller since commit 052eb2d49006 ("spi: core: Set
max_speed_hz of spi_device default to max_speed_hz of controller").

Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: sh-msiof: Document r8a77470 bindings

Document SoC specific bindings for R-Car RZ/G1C(r8a77470) SoC.

Signed-off-by: Cao Van Dong <cv-dong@jinso.co.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: pxa2xx: use a module softdep for dw_dmac

With dw_dmac, sometimes the request of a DMA channel fails because
the DMA driver is not ready, so an explicit dependency request
is necessary.

Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: spi-mem: Make spi_mem_default_supports_op() static inline

Stub helper spi_mem_default_supports_op() should
be set to static inline

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

spi: spi-mem: Fix build error without CONFIG_SPI_MEM

When building with CONFIG_SPI_MEM is not set
gc warns this:

drivers/spi/spi-zynq-qspi.o: In function `zynq_qspi_supports_op':
spi-zynq-qspi.c:(.text+0x1da): undefined reference to `spi_mem_default_supports_op'

Fixes: 67dca5e580f1 ("spi: spi-mem: Add support for Zynq QSPI controller")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Linux 5.1-rc7

Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm

Pull ARM fixes from Russell King:
"A small number of ARM fixes

   - Fix function tracer and unwinder dependencies so that we don't end
     up building kernels that will crash

   - Fix ARMv7M nommu initialisation (missing register initialisation)

   - Fix EFI decompressor entry (ensuring barrier instructions are
     enabled prior to use)"

* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
  ARM: 8857/1: efi: enable CP15 DMB instructions before cleaning the cache
  ARM: 8856/1: NOMMU: Fix CCR register faulty initialization when MPU is disabled
  ARM: fix function graph tracer and unwinder dependencies

Merge tag 'powerpc-5.1-6' of git://git./linux/kernel/git/powerpc/linux

Pull powerpc fixes from Michael Ellerman:
"A one-liner to make our Radix MMU support depend on HUGETLB_PAGE. We
  use some of the hugetlb inlines (eg. pud_huge()) when operating on the
  linear mapping and if they're compiled into empty wrappers we can
  corrupt memory.

  Then two fixes to our VFIO IOMMU code. The first is not a regression
  but fixes the locking to avoid a user-triggerable deadlock.

  The second does fix a regression since rc1, and depends on the first
  fix. It makes it possible to run guests with large amounts of memory
  again (~256GB).

  Thanks to Alexey Kardashevskiy"

* tag 'powerpc-5.1-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/mm_iommu: Allow pinning large regions
  powerpc/mm_iommu: Fix potential deadlock
  powerpc/mm/radix: Make Radix require HUGETLB_PAGE

Merge tag 'for-linus-20190428' of git://git.kernel.dk/linux-block

Pull block fixes from Jens Axboe:
"A set of io_uring fixes that should go into this release. In
  particular, this contains:

   - The mutex lock vs ctx ref count fix (me)

   - Removal of a dead variable (me)

   - Two race fixes (Stefan)

   - Ring head/tail condition fix for poll full SQ detection (Stefan)"

* tag 'for-linus-20190428' of git://git.kernel.dk/linux-block:
  io_uring: remove 'state' argument from io_{read,write} path
  io_uring: fix poll full SQ detection
  io_uring: fix race condition when sq threads goes sleeping
  io_uring: fix race condition reading SQ entries
  io_uring: fail io_uring_register(2) on a dying io_uring instance

Merge tag 'for-linus' of git://git./linux/kernel/git/rdma/rdma

Pull rdma fixes from Jason Gunthorpe:
"One core bug fix and a few driver ones

   - FRWR memory registration for hfi1/qib didn't work with with some
     iovas causing a NFSoRDMA failure regression due to a fix in the NFS
     side

   - A command flow error in mlx5 allowed user space to send a corrupt
     command (and also smash the kernel stack we've since learned)

   - Fix a regression and some bugs with device hot unplug that was
     discovered while reviewing Andrea's patches

   - hns has a failure if the user asks for certain QP configurations"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
  RDMA/hns: Bugfix for mapping user db
  RDMA/ucontext: Fix regression with disassociate
  RDMA/mlx5: Use rdma_user_map_io for mapping BAR pages
  RDMA/mlx5: Do not allow the user to write to the clock page
  IB/mlx5: Fix scatter to CQE in DCT QP creation
  IB/rdmavt: Fix frwr memory registration

Merge tag 'dmaengine-fix-5.1-rc7' of git://git.infradead.org/users/vkoul/slave-dma

Pull dmaengine fixes from Vinod Koul:

- fix for wrong register use in mediatek driver

- fix in sh driver for glitch is tx_status and treating 0 a valid
   residue for cyclic

- fix in bcm driver for using right memory allocation flag

* tag 'dmaengine-fix-5.1-rc7' of git://git.infradead.org/users/vkoul/slave-dma:
  dmaengine: mediatek-cqdma: fix wrong register usage in mtk_cqdma_start
  dmaengine: sh: rcar-dmac: Fix glitch in dmaengine_tx_status
  dmaengine: sh: rcar-dmac: With cyclic DMA residue 0 is valid
  dmaengine: bcm2835: Avoid GFP_KERNEL in device_prep_slave_sg

Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input

Pull input fixes from Dmitry Torokhov:
"Just a couple of fixups for Synaptics RMI4 driver and allowing
  snvs_pwrkey to be selected on more boards"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: synaptics-rmi4 - write config register values to the right offset
  Input: synaptics-rmi4 - fix possible double free
  Input: snvs_pwrkey - make it depend on ARCH_MXC

Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull x86 fixes from Ingo Molnar:

- Fix an early boot crash in the RSDP parsing code by effectively
   turning off the parsing call - we ran out of time but want to fix the
   regression. The more involved fix is being worked on.

- Fix a crash that can trigger in the kmemlek code.

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mm: Fix a crash with kmemleak_scan()
  x86/boot: Disable RSDP parsing temporarily

Merge branch 'sched-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull scheduler fix from Ingo Molnar:
"Fix a division by zero bug that can trigger in the NUMA placement
code"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/numa: Fix a possible divide-by-zero

Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull perf fix from Ingo Molnar:
"A cstate event enumeration fix for Kaby/Coffee Lake CPUs"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel: Update KBL Package C-state events to also include PC8/PC9/PC10 counters

slip: make slhc_free() silently accept an error pointer

This way, slhc_free() accepts what slhc_init() returns, whether that is
an error or not.

In particular, the pattern in sl_alloc_bufs() is

        slcomp = slhc_init(16, 16);
        ...
        slhc_free(slcomp);

for the error handling path, and rather than complicate that code, just
make it ok to always free what was returned by the init function.

That's what the code used to do before commit 4ab42d78e37a ("ppp, slip:
Validate VJ compression slot parameters completely") when slhc_init()
just returned NULL for the error case, with no actual indication of the
details of the error.

Reported-by: syzbot+45474c076a4927533d2e@syzkaller.appspotmail.com
Fixes: 4ab42d78e37a ("ppp, slip: Validate VJ compression slot parameters completely")
Acked-by: Ben Hutchings <ben@decadent.org.uk>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'akpm' (patches from Andrew)

Merge misc fixes from Andrew Morton:
"9 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  fs/proc/proc_sysctl.c: Fix a NULL pointer dereference
  mm/page_alloc.c: fix never set ALLOC_NOFRAGMENT flag
  mm/page_alloc.c: avoid potential NULL pointer dereference
  mm, page_alloc: always use a captured page regardless of compaction result
  mm: do not boost watermarks to avoid fragmentation for the DISCONTIG memory model
  lib/test_vmalloc.c: do not create cpumask_t variable on stack
  lib/Kconfig.debug: fix build error without CONFIG_BLOCK
  zram: pass down the bvec we need to read into in the work struct
  mm/memory_hotplug.c: drop memory device reference after find_memory_block()

Input: synaptics-rmi4 - write config register values to the right offset

Currently any changed config register values don't take effect, as the
function to write them back is called with the wrong register offset.

Fixes: ff8f83708b3e (Input: synaptics-rmi4 - add support for 2D
sensors and F11)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux

Pull arm64 fixes from Catalin Marinas:

- keep the tail of an unaligned initrd reserved

- adjust ftrace_make_call() to deal with the relative nature of PLTs

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64/module: ftrace: deal with place relative nature of PLTs
arm64: mm: Ensure tail of unaligned initrd is reserved

Merge tag 'trace-v5.1-rc6' of git://git./linux/kernel/git/rostedt/linux-trace

Pull tracing fixes from Steven Rostedt:
"Three tracing fixes:

   - Use "nosteal" for ring buffer splice pages

   - Memory leak fix in error path of trace_pid_write()

   - Fix preempt_enable_no_resched() (use preempt_enable()) in ring
     buffer code"

* tag 'trace-v5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  trace: Fix preempt_enable_no_resched() abuse
  tracing: Fix a memory leak by early error exit in trace_pid_write()
  tracing: Fix buffer_ref pipe ops

Merge tag 'gpio-v5.1-3' of git://git./linux/kernel/git/linusw/linux-gpio

Pull GPIO fixes from Linus Walleij:
"Not much to say about them, regular fixes:

   - Fix a bug on the errorpath of gpiochip_add_data_with_key()

   - IRQ type setting on the spreadtrum GPIO driver"

* tag 'gpio-v5.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio: Fix gpiochip_add_data_with_key() error path
  gpio: eic: sprd: Fix incorrect irq type setting for the sync EIC

Merge tag 'drm-fixes-2019-04-26' of git://anongit.freedesktop.org/drm/drm

Pull drm fixes from Dave Airlie:
"Regular drm fixes, nothing too outstanding, I'm guessing Easter was
  slowing people down.

  i915:
   - FEC enable fix
   - BXT display lanes fix

  ttm:
   - fix reinit for reloading drivers regression

  imx:
   - DP CSC fix

  sun4i:
   - module unload/load fix

  vc4:
   - memory leak fix
   - compile fix

  dw-hdmi:
   - rockchip scdc overflow fix

  sched:
   - docs fix

  vmwgfx:
   - dma api layering fix"

* tag 'drm-fixes-2019-04-26' of git://anongit.freedesktop.org/drm/drm:
  drm/bridge: dw-hdmi: fix SCDC configuration for ddc-i2c-bus
  drm/vmwgfx: Fix dma API layer violation
  drm/vc4: Fix compilation error reported by kbuild test bot
  drm/sun4i: Unbind components before releasing DRM and memory
  drm/vc4: Fix memory leak during gpu reset.
  drm/sched: Fix description of drm_sched_stop
  drm/imx: don't skip DP channel disable for background plane
  gpu: ipu-v3: dp: fix CSC handling
  drm/ttm: fix re-init of global structures
  drm/sun4i: Fix component unbinding and component master deletion
  drm/sun4i: Set device driver data at bind time for use in unbind
  drm/sun4i: Add missing drm_atomic_helper_shutdown at driver unbind
  drm/i915: Restore correct bxt_ddi_phy_calc_lane_lat_optim_mask() calculation
  drm/i915: Do not enable FEC without DSC
  drm: bridge: dw-hdmi: Fix overflow workaround for Rockchip SoCs

Merge tag 'for-5.1-rc6-tag' of git://git./linux/kernel/git/kdave/linux

Pull btrfs fix from David Sterba:
"One patch to fix a crash in io submission path, due to memory
  allocation errors.

  In short, the multipage bio work that landed in 5.1 caused larger bios
  that in turn require larger temporary memory for checksums. The patch
  is a workaround, we're going to rework the allocation so it does not
  require the vmalloc fallback.

  It took a while to identify that it's caused by patches in 5.1 and not
  a patchset that did some changes in error handling in the code. I've
  tested it on various memory/cpu combinations, it could hit OOM but
  does not crash.

  The timestamp of the patch is less than a day due to updates in the
  changelog, tests were running meanwhile"

* tag 'for-5.1-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: Switch memory allocations in async csum calculation path to kvmalloc

Merge tag '5.1-rc6-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6

Pull cifs fixes from Steve French:
"Three small SMB3 fixes (all for stable as well): two leaks and a
  rename bug"

* tag '5.1-rc6-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: fix page reference leak with readv/writev
  cifs: do not attempt cifs operation on smb2+ rename error
  cifs: fix memory leak in SMB2_read

fs/proc/proc_sysctl.c: Fix a NULL pointer dereference

Syzkaller report this:

  sysctl could not get directory: /net//bridge -12
  kasan: CONFIG_KASAN_INLINE enabled
  kasan: GPF could be caused by NULL-ptr deref or user memory access
  general protection fault: 0000 [#1] SMP KASAN PTI
  CPU: 1 PID: 7027 Comm: syz-executor.0 Tainted: G         C        5.1.0-rc3+ #8
  Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
  RIP: 0010:__write_once_size include/linux/compiler.h:220 [inline]
  RIP: 0010:__rb_change_child include/linux/rbtree_augmented.h:144 [inline]
  RIP: 0010:__rb_erase_augmented include/linux/rbtree_augmented.h:186 [inline]
  RIP: 0010:rb_erase+0x5f4/0x19f0 lib/rbtree.c:459
  Code: 00 0f 85 60 13 00 00 48 89 1a 48 83 c4 18 5b 5d 41 5c 41 5d 41 5e 41 5f c3 48 89 f2 48 b8 00 00 00 00 00 fc ff df 48 c1 ea 03 <80> 3c 02 00 0f 85 75 0c 00 00 4d 85 ed 4c 89 2e 74 ce 4c 89 ea 48
  RSP: 0018:ffff8881bb507778 EFLAGS: 00010206
  RAX: dffffc0000000000 RBX: ffff8881f224b5b8 RCX: ffffffff818f3f6a
  RDX: 000000000000000a RSI: 0000000000000050 RDI: ffff8881f224b568
  RBP: 0000000000000000 R08: ffffed10376a0ef4 R09: ffffed10376a0ef4
  R10: 0000000000000001 R11: ffffed10376a0ef4 R12: ffff8881f224b558
  R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
  FS:  00007f3e7ce13700(0000) GS:ffff8881f7300000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 00007fd60fbe9398 CR3: 00000001cb55c001 CR4: 00000000007606e0
  DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
  DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
  PKRU: 55555554
  Call Trace:
   erase_entry fs/proc/proc_sysctl.c:178 [inline]
   erase_header+0xe3/0x160 fs/proc/proc_sysctl.c:207
   start_unregistering fs/proc/proc_sysctl.c:331 [inline]
   drop_sysctl_table+0x558/0x880 fs/proc/proc_sysctl.c:1631
   get_subdir fs/proc/proc_sysctl.c:1022 [inline]
   __register_sysctl_table+0xd65/0x1090 fs/proc/proc_sysctl.c:1335
   br_netfilter_init+0x68/0x1000 [br_netfilter]
   do_one_initcall+0xbc/0x47d init/main.c:901
   do_init_module+0x1b5/0x547 kernel/module.c:3456
   load_module+0x6405/0x8c10 kernel/module.c:3804
   __do_sys_finit_module+0x162/0x190 kernel/module.c:3898
   do_syscall_64+0x9f/0x450 arch/x86/entry/common.c:290
   entry_SYSCALL_64_after_hwframe+0x49/0xbe
  Modules linked in: br_netfilter(+) backlight comedi(C) hid_sensor_hub max3100 ti_ads8688 udc_core fddi snd_mona leds_gpio rc_streamzap mtd pata_netcell nf_log_common rc_winfast udp_tunnel snd_usbmidi_lib snd_usb_toneport snd_usb_line6 snd_rawmidi snd_seq_device snd_hwdep videobuf2_v4l2 videobuf2_common videodev media videobuf2_vmalloc videobuf2_memops rc_gadmei_rm008z 8250_of smm665 hid_tmff hid_saitek hwmon_vid rc_ati_tv_wonder_hd_600 rc_core pata_pdc202xx_old dn_rtmsg as3722 ad714x_i2c ad714x snd_soc_cs4265 hid_kensington panel_ilitek_ili9322 drm drm_panel_orientation_quirks ipack cdc_phonet usbcore phonet hid_jabra hid extcon_arizona can_dev industrialio_triggered_buffer kfifo_buf industrialio adm1031 i2c_mux_ltc4306 i2c_mux ipmi_msghandler mlxsw_core snd_soc_cs35l34 snd_soc_core snd_pcm_dmaengine snd_pcm snd_timer ac97_bus snd_compress snd soundcore gpio_da9055 uio ecdh_generic mdio_thunder of_mdio fixed_phy libphy mdio_cavium iptable_security iptable_raw iptable_mangle
   iptable_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 iptable_filter bpfilter ip6_vti ip_vti ip_gre ipip sit tunnel4 ip_tunnel hsr veth netdevsim vxcan batman_adv cfg80211 rfkill chnl_net caif nlmon dummy team bonding vcan bridge stp llc ip6_gre gre ip6_tunnel tunnel6 tun joydev mousedev ppdev tpm kvm_intel kvm irqbypass crct10dif_pclmul crc32_pclmul crc32c_intel ghash_clmulni_intel aesni_intel ide_pci_generic piix aes_x86_64 crypto_simd cryptd ide_core glue_helper input_leds psmouse intel_agp intel_gtt serio_raw ata_generic i2c_piix4 agpgart pata_acpi parport_pc parport floppy rtc_cmos sch_fq_codel ip_tables x_tables sha1_ssse3 sha1_generic ipv6 [last unloaded: br_netfilter]
  Dumping ftrace buffer:
     (ftrace buffer empty)
  ---[ end trace 68741688d5fbfe85 ]---

commit 23da9588037e ("fs/proc/proc_sysctl.c: fix NULL pointer
dereference in put_links") forgot to handle start_unregistering() case,
while header->parent is NULL, it calls erase_header() and as seen in the
above syzkaller call trace, accessing &header->parent->root will trigger
a NULL pointer dereference.

As that commit explained, there is also no need to call
start_unregistering() if header->parent is NULL.

Link: http://lkml.kernel.org/r/20190409153622.28112-1-yuehaibing@huawei.com
Fixes: 23da9588037e ("fs/proc/proc_sysctl.c: fix NULL pointer dereference in put_links")
Fixes: 0e47c99d7fe25 ("sysctl: Replace root_list with links between sysctl_table_sets")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm/page_alloc.c: fix never set ALLOC_NOFRAGMENT flag

Commit 0a79cdad5eb2 ("mm: use alloc_flags to record if kswapd can wake")
removed setting of the ALLOC_NOFRAGMENT flag. Bring it back.

The runtime effect is that ALLOC_NOFRAGMENT behaviour is restored so
that allocations are spread across local zones to avoid fragmentation
due to mixing pageblocks as long as possible.

Link: http://lkml.kernel.org/r/20190423120806.3503-2-aryabinin@virtuozzo.com
Fixes: 0a79cdad5eb2 ("mm: use alloc_flags to record if kswapd can wake")
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm/page_alloc.c: avoid potential NULL pointer dereference

ac.preferred_zoneref->zone passed to alloc_flags_nofragment() can be NULL.
'zone' pointer unconditionally derefernced in alloc_flags_nofragment().
Bail out on NULL zone to avoid potential crash. Currently we don't see
any crashes only because alloc_flags_nofragment() has another bug which
allows compiler to optimize away all accesses to 'zone'.

Link: http://lkml.kernel.org/r/20190423120806.3503-1-aryabinin@virtuozzo.com
Fixes: 6bb154504f8b ("mm, page_alloc: spread allocations across zones before introducing fragmentation")
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm, page_alloc: always use a captured page regardless of compaction result

During the development of commit 5e1f0f098b46 ("mm, compaction: capture
a page under direct compaction"), a paranoid check was added to ensure
that if a captured page was available after compaction that it was
consistent with the final state of compaction.  The intent was to catch
serious programming bugs such as using a stale page pointer and causing
corruption problems.

However, it is possible to get a captured page even if compaction was
unsuccessful if an interrupt triggered and happened to free pages in
interrupt context that got merged into a suitable high-order page.  It's
highly unlikely but Li Wang did report the following warning on s390
occuring when testing OOM handling.  Note that the warning is slightly
edited for clarity.

  WARNING: CPU: 0 PID: 9783 at mm/page_alloc.c:3777 __alloc_pages_direct_compact+0x182/0x190
  Modules linked in: rpcsec_gss_krb5 auth_rpcgss nfsv4 dns_resolver nfs
    lockd grace fscache sunrpc pkey ghash_s390 prng xts aes_s390
    des_s390 des_generic sha512_s390 zcrypt_cex4 zcrypt vmur binfmt_misc
    ip_tables xfs libcrc32c dasd_fba_mod qeth_l2 dasd_eckd_mod dasd_mod
    qeth qdio lcs ctcm ccwgroup fsm dm_mirror dm_region_hash dm_log
    dm_mod
  CPU: 0 PID: 9783 Comm: copy.sh Kdump: loaded Not tainted 5.1.0-rc 5 #1

This patch simply removes the check entirely instead of trying to be
clever about pages freed from interrupt context.  If a serious
programming error was introduced, it is highly likely to be caught by
prep_new_page() instead.

Link: http://lkml.kernel.org/r/20190419085133.GH18914@techsingularity.net
Fixes: 5e1f0f098b46 ("mm, compaction: capture a page under direct compaction")
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Reported-by: Li Wang <liwang@redhat.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: do not boost watermarks to avoid fragmentation for the DISCONTIG memory model

Mikulas Patocka reported that commit 1c30844d2dfe ("mm: reclaim small
amounts of memory when an external fragmentation event occurs") "broke"
memory management on parisc.

The machine is not NUMA but the DISCONTIG model creates three pgdats
even though it's a UMA machine for the following ranges

        0) Start 0x0000000000000000 End 0x000000003fffffff Size   1024 MB
        1) Start 0x0000000100000000 End 0x00000001bfdfffff Size   3070 MB
        2) Start 0x0000004040000000 End 0x00000040ffffffff Size   3072 MB

Mikulas reported:

With the patch 1c30844d2, the kernel will incorrectly reclaim the
first zone when it fills up, ignoring the fact that there are two
completely free zones. Basiscally, it limits cache size to 1GiB.

For example, if I run:
# dd if=/dev/sda of=/dev/null bs=1M count=2048

- with the proper kernel, there should be "Buffers - 2GiB"
when this command finishes. With the patch 1c30844d2, buffers
will consume just 1GiB or slightly more, because the kernel was
incorrectly reclaiming them.

The page allocator and reclaim makes assumptions that pgdats really
represent NUMA nodes and zones represent ranges and makes decisions on
that basis.  Watermark boosting for small pgdats leads to unexpected
results even though this would have behaved reasonably on SPARSEMEM.

DISCONTIG is essentially deprecated and even parisc plans to move to
SPARSEMEM so there is no need to be fancy, this patch simply disables
watermark boosting by default on DISCONTIGMEM.

Link: http://lkml.kernel.org/r/20190419094335.GJ18914@techsingularity.net
Fixes: 1c30844d2dfe ("mm: reclaim small amounts of memory when an external fragmentation event occurs")
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Tested-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: James Bottomley <James.Bottomley@hansenpartnership.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

lib/test_vmalloc.c: do not create cpumask_t variable on stack

On my "Intel(R) Xeon(R) W-2135 CPU @ 3.70GHz" system(12 CPUs) i get the
warning from the compiler about frame size:

warning: the frame size of 1096 bytes is larger than 1024 bytes [-Wframe-larger-than=]

the size of cpumask_t depends on number of CPUs, therefore just make use
of cpumask_of() in set_cpus_allowed_ptr() as a second argument.

Link: http://lkml.kernel.org/r/20190418193925.9361-1-urezki@gmail.com
Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Roman Gushchin <guro@fb.com>
Cc: Uladzislau Rezki <urezki@gmail.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Thomas Garnier <thgarnie@google.com>
Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Joel Fernandes <joelaf@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

lib/Kconfig.debug: fix build error without CONFIG_BLOCK

If CONFIG_TEST_KMOD is set to M, while CONFIG_BLOCK is not set, XFS and
BTRFS can not be compiled successly.

Link: http://lkml.kernel.org/r/20190410075434.35220-1-yuehaibing@huawei.com
Fixes: d9c6a72d6fa2 ("kmod: add test driver to stress test the module loader")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Joe Lawrence <joe.lawrence@redhat.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

zram: pass down the bvec we need to read into in the work struct

When scheduling work item to read page we need to pass down the proper
bvec struct which points to the page to read into. Before this patch it
uses a randomly initialized bvec (only if PAGE_SIZE != 4096) which is
wrong.

Note that without this patch on arch/kernel where PAGE_SIZE != 4096
userspace could read random memory through a zram block device (thought
userspace probably would have no control on the address being read).

Link: http://lkml.kernel.org/r/20190408183219.26377-1-jglisse@redhat.com
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm/memory_hotplug.c: drop memory device reference after find_memory_block()

Right now we are using find_memory_block() to get the node id for the
pfn range to online.  We are missing to drop a reference to the memory
block device.  While the device still gets unregistered via
device_unregister(), resulting in no user visible problem, the device is
never released via device_release(), resulting in a memory leak.  Fix
that by properly using a put_device().

Link: http://lkml.kernel.org/r/20190411110955.1430-1-david@redhat.com
Fixes: d0dc12e86b31 ("mm/memory_hotplug: optimize memory hotplug")
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Reviewed-by: Wei Yang <richard.weiyang@gmail.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Pankaj Gupta <pagupta@redhat.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Qian Cai <cai@lca.pw>
Cc: Arun KS <arunks@codeaurora.org>
Cc: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

trace: Fix preempt_enable_no_resched() abuse

Unless the very next line is schedule(), or implies it, one must not use
preempt_enable_no_resched(). It can cause a preemption to go missing and
thereby cause arbitrary delays, breaking the PREEMPT=y invariant.

Link: http://lkml.kernel.org/r/20190423200318.GY14281@hirez.programming.kicks-ass.net
Cc: Waiman Long <longman@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: the arch/x86 maintainers <x86@kernel.org>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: huang ying <huang.ying.caritas@gmail.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: stable@vger.kernel.org
Fixes: 2c2d7329d8af ("tracing/ftrace: use preempt_enable_no_resched_notrace in ring_buffer_time_stamp()")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>

tracing: Fix a memory leak by early error exit in trace_pid_write()

In trace_pid_write(), the buffer for trace parser is allocated through
kmalloc() in trace_parser_get_init(). Later on, after the buffer is used,
it is then freed through kfree() in trace_parser_put(). However, it is
possible that trace_pid_write() is terminated due to unexpected errors,
e.g., ENOMEM. In that case, the allocated buffer will not be freed, which
is a memory leak bug.

To fix this issue, free the allocated buffer when an error is encountered.

Link: http://lkml.kernel.org/r/1555726979-15633-1-git-send-email-wang6495@umn.edu
Fixes: f4d34a87e9c10 ("tracing: Use pid bitmap instead of a pid array for set_event_pid")
Cc: stable@vger.kernel.org
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>

tracing: Fix buffer_ref pipe ops

This fixes multiple issues in buffer_pipe_buf_ops:

- The ->steal() handler must not return zero unless the pipe buffer has
   the only reference to the page. But generic_pipe_buf_steal() assumes
   that every reference to the pipe is tracked by the page's refcount,
   which isn't true for these buffers - buffer_pipe_buf_get(), which
   duplicates a buffer, doesn't touch the page's refcount.
   Fix it by using generic_pipe_buf_nosteal(), which refuses every
   attempted theft. It should be easy to actually support ->steal, but the
   only current users of pipe_buf_steal() are the virtio console and FUSE,
   and they also only use it as an optimization. So it's probably not worth
   the effort.
- The ->get() and ->release() handlers can be invoked concurrently on pipe
   buffers backed by the same struct buffer_ref. Make them safe against
   concurrency by using refcount_t.
- The pointers stored in ->private were only zeroed out when the last
   reference to the buffer_ref was dropped. As far as I know, this
   shouldn't be necessary anyway, but if we do it, let's always do it.

Link: http://lkml.kernel.org/r/20190404215925.253531-1-jannh@google.com
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: stable@vger.kernel.org
Fixes: 73a757e63114d ("ring-buffer: Return reader page back into existing ring buffer")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>

dmaengine: mediatek-cqdma: fix wrong register usage in mtk_cqdma_start

This patch fixes wrong register usage in the mtk_cqdma_start. The
destination register should be MTK_CQDMA_DST2 instead.

Fixes: b1f01e48df5a ("dmaengine: mediatek: Add MediaTek Command-Queue DMA controller for MT6765 SoC")
Signed-off-by: Shun-Chih Yu <shun-chih.yu@mediatek.com>
Cc: stable@vger.kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Merge tag 'imx-drm-fixes-2019-04-25' of git://git.pengutronix.de/pza/linux into drm-fixes

drm/imx: fix DP CSC handling

- Fix the DP color space conversion matrix setup to avoid bugs where
  disabling the overlay plane while both primary and overlay plane are
  routed via the CSC unit would not reconfigure the CSC routing
  properly, leaving the display in a nonworking state, or the CSC
  setting from a previously set mode would be left behind, causing
  wrong colors when reenabling the display in certain configurations.

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/1556183136.2271.3.camel@pengutronix.de

Merge branch 'vmwgfx-fixes-5.1' of git://people.freedesktop.org/~thomash/linux into drm-fixes

A single fix for a layer violation requested by Cristoph.

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Hellstrom <thellstrom@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190425204100.3982-1-thellstrom@vmware.com

Merge tag 'drm-misc-fixes-2019-04-25' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes

- sun4i: Fix module loading / unloading
- vc4: Fix a compilation error and memory leak
- dw-hdmi: Fix an overflow on Rockchip and SCDC configuration

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190425132739.pngmfiqucqmulxkz@flea

Merge branch 'drm-fixes-5.1' of git://people.freedesktop.org/~agd5f/linux into drm-fixes

- ttm regression fix
- sched documentation fix

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190424230120.3423-1-alexander.deucher@amd.com

Merge tag 'drm-intel-fixes-2019-04-24' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes

A fix for display lanes calculation for BXT and a protection
to avoid enabling FEC without DSC.

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190424215359.GA26100@intel.com

sched/numa: Fix a possible divide-by-zero

sched_clock_cpu() may not be consistent between CPUs. If a task
migrates to another CPU, then se.exec_start is set to that CPU's
rq_clock_task() by update_stats_curr_start(). Specifically, the new
value might be before the old value due to clock skew.

So then if in numa_get_avg_runtime() the expression:

'now - p->last_task_numa_placement'

ends up as -1, then the divider '*period + 1' in task_numa_placement()
is 0 and things go bang. Similar to update_curr(), check if time goes
backwards to avoid this.

[ peterz: Wrote new changelog. ]
[ mingo: Tweaked the code comment. ]

Signed-off-by: Xie XiuQi <xiexiuqi@huawei.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: cj.chengjian@huawei.com
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20190425080016.GX11158@hirez.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>

Merge tag 'ceph-for-5.1-rc7' of git://github.com/ceph/ceph-client

Pull ceph fixes from Ilya Dryomov:
"dentry name handling fixes from Jeff and a memory leak fix from Zheng.

  Both are old issues, marked for stable"

* tag 'ceph-for-5.1-rc7' of git://github.com/ceph/ceph-client:
  ceph: fix ci->i_head_snapc leak
  ceph: handle the case where a dentry has been renamed on outstanding req
  ceph: ensure d_name stability in ceph_dentry_hash()
  ceph: only use d_name directly when parent is locked

Merge branch 'linus' of git://git./linux/kernel/git/herbert/crypto-2.6

Pull crypto fixes from Herbert Xu:
"This fixes a bug in xts and lrw where they may sleep in an atomic
  context"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: lrw - Fix atomic sleep when walking skcipher
  crypto: xts - Fix atomic sleep when walking skcipher

RDMA/hns: Bugfix for mapping user db

When the maximum send wr delivered by the user is zero, the qp does not
have a sq.

When allocating the sq db buffer to store the user sq pi pointer and map
it to the kernel mode, max_send_wr is used as the trigger condition, while
the kernel does not consider the max_send_wr trigger condition when
mapmping db. It will cause sq record doorbell map fail and create qp fail.

The failed print information as follows:

hns3 0000:7d:00.1: Send cmd: tail - 418, opcode - 0x8504, flag - 0x0011, retval - 0x0000
hns3 0000:7d:00.1: Send cmd: 0xe59dc000 0x00000000 0x00000000 0x00000000 0x00000116 0x0000ffff
hns3 0000:7d:00.1: sq record doorbell map failed!
hns3 0000:7d:00.1: Create RC QP failed

Fixes: 0425e3e6e0c7 ("RDMA/hns: Support flush cqe for hip08 in kernel space")
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>

btrfs: Switch memory allocations in async csum calculation path to kvmalloc

Recent multi-page biovec rework allowed creation of bios that can span
large regions - up to 128 megabytes in the case of btrfs. OTOH btrfs'
submission path currently allocates a contiguous array to store the
checksums for every bio submitted. This means we can request up to
(128mb / BTRFS_SECTOR_SIZE) * 4 bytes + 32bytes of memory from kmalloc.
On busy systems with possibly fragmented memory said kmalloc can fail
which will trigger BUG_ON due to improper error handling IO submission
context in btrfs.

Until error handling is improved or bios in btrfs limited to a more
manageable size (e.g. 1m) let's use kvmalloc to fallback to vmalloc for
such large allocations. There is no hard requirement that the memory
allocated for checksums during IO submission has to be contiguous, but
this is a simple fix that does not require several non-contiguous
allocations.

For small writes this is unlikely to have any visible effect since
kmalloc will still satisfy allocation requests as usual. For larger
requests the code will just fallback to vmalloc.

We've performed evaluation on several workload types and there was no
significant difference kmalloc vs kvmalloc.

Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>

drm/bridge: dw-hdmi: fix SCDC configuration for ddc-i2c-bus

When ddc-i2c-bus property is used, a NULL pointer dereference is reported:

[   31.041669] Unable to handle kernel NULL pointer dereference at virtual address 00000008
[   31.041671] pgd = 4d3c16f6
[   31.041673] [00000008] *pgd=00000000
[   31.041678] Internal error: Oops: 5 [#1] SMP ARM

[   31.041711] Hardware name: Rockchip (Device Tree)
[   31.041718] PC is at i2c_transfer+0x8/0xe4
[   31.041721] LR is at drm_scdc_read+0x54/0x84
[   31.041723] pc : [<c073273c>]    lr : [<c05926c4>]    psr: 280f0013
[   31.041725] sp : edffdad0  ip : 5ccb5511  fp : 00000058
[   31.041727] r10: 00000780  r9 : edf91608  r8 : c11b0f48
[   31.041728] r7 : 00000438  r6 : 00000000  r5 : 00000000  r4 : 00000000
[   31.041730] r3 : edffdae7  r2 : 00000002  r1 : edffdaec  r0 : 00000000

[   31.041908] [<c073273c>] (i2c_transfer) from [<c05926c4>] (drm_scdc_read+0x54/0x84)
[   31.041913] [<c05926c4>] (drm_scdc_read) from [<c0592858>] (drm_scdc_set_scrambling+0x30/0xbc)
[   31.041919] [<c0592858>] (drm_scdc_set_scrambling) from [<c05cc0f4>] (dw_hdmi_update_power+0x1440/0x1610)
[   31.041926] [<c05cc0f4>] (dw_hdmi_update_power) from [<c05cc574>] (dw_hdmi_bridge_enable+0x2c/0x70)
[   31.041932] [<c05cc574>] (dw_hdmi_bridge_enable) from [<c05aed48>] (drm_bridge_enable+0x24/0x34)
[   31.041938] [<c05aed48>] (drm_bridge_enable) from [<c0591060>] (drm_atomic_helper_commit_modeset_enables+0x114/0x220)
[   31.041943] [<c0591060>] (drm_atomic_helper_commit_modeset_enables) from [<c05c3fe0>] (rockchip_atomic_helper_commit_tail_rpm+0x28/0x64)

hdmi->i2c may not be set when ddc-i2c-bus property is used in device tree.
Fix this by using hdmi->ddc as the i2c adapter when calling drm_scdc_*().
Also report that SCDC is not supported when there is no DDC bus.

Fixes: 264fce6cc2c1 ("drm/bridge: dw-hdmi: Add SCDC and TMDS Scrambling support")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/VE1PR03MB59031814B5BCAB2152923BDAAC210@VE1PR03MB5903.eurprd03.prod.outlook.com

gpio: Fix gpiochip_add_data_with_key() error path

The err_remove_chip block is too coarse, and may perform cleanup that
must not be done.  E.g. if of_gpiochip_add() fails, of_gpiochip_remove()
is still called, causing:

    OF: ERROR: Bad of_node_put() on /soc/gpio@e6050000
    CPU: 1 PID: 20 Comm: kworker/1:1 Not tainted 5.1.0-rc2-koelsch+ #407
    Hardware name: Generic R-Car Gen2 (Flattened Device Tree)
    Workqueue: events deferred_probe_work_func
    [<c020ec74>] (unwind_backtrace) from [<c020ae58>] (show_stack+0x10/0x14)
    [<c020ae58>] (show_stack) from [<c07c1224>] (dump_stack+0x7c/0x9c)
    [<c07c1224>] (dump_stack) from [<c07c5a80>] (kobject_put+0x94/0xbc)
    [<c07c5a80>] (kobject_put) from [<c0470420>] (gpiochip_add_data_with_key+0x8d8/0xa3c)
    [<c0470420>] (gpiochip_add_data_with_key) from [<c0473738>] (gpio_rcar_probe+0x1d4/0x314)
    [<c0473738>] (gpio_rcar_probe) from [<c052fca8>] (platform_drv_probe+0x48/0x94)

and later, if a GPIO consumer tries to use a GPIO from a failed
controller:

    WARNING: CPU: 0 PID: 1 at lib/refcount.c:156 kobject_get+0x38/0x4c
    refcount_t: increment on 0; use-after-free.
    Modules linked in:
    CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.1.0-rc2-koelsch+ #407
    Hardware name: Generic R-Car Gen2 (Flattened Device Tree)
    [<c020ec74>] (unwind_backtrace) from [<c020ae58>] (show_stack+0x10/0x14)
    [<c020ae58>] (show_stack) from [<c07c1224>] (dump_stack+0x7c/0x9c)
    [<c07c1224>] (dump_stack) from [<c0221580>] (__warn+0xd0/0xec)
    [<c0221580>] (__warn) from [<c02215e0>] (warn_slowpath_fmt+0x44/0x6c)
    [<c02215e0>] (warn_slowpath_fmt) from [<c07c58fc>] (kobject_get+0x38/0x4c)
    [<c07c58fc>] (kobject_get) from [<c068b3ec>] (of_node_get+0x14/0x1c)
    [<c068b3ec>] (of_node_get) from [<c0686f24>] (of_find_node_by_phandle+0xc0/0xf0)
    [<c0686f24>] (of_find_node_by_phandle) from [<c0686fbc>] (of_phandle_iterator_next+0x68/0x154)
    [<c0686fbc>] (of_phandle_iterator_next) from [<c0687fe4>] (__of_parse_phandle_with_args+0x40/0xd0)
    [<c0687fe4>] (__of_parse_phandle_with_args) from [<c0688204>] (of_parse_phandle_with_args_map+0x100/0x3ac)
    [<c0688204>] (of_parse_phandle_with_args_map) from [<c0471240>] (of_get_named_gpiod_flags+0x38/0x380)
    [<c0471240>] (of_get_named_gpiod_flags) from [<c046f864>] (gpiod_get_from_of_node+0x24/0xd8)
    [<c046f864>] (gpiod_get_from_of_node) from [<c0470aa4>] (devm_fwnode_get_index_gpiod_from_child+0xa0/0x144)
    [<c0470aa4>] (devm_fwnode_get_index_gpiod_from_child) from [<c05f425c>] (gpio_keys_probe+0x418/0x7bc)
    [<c05f425c>] (gpio_keys_probe) from [<c052fca8>] (platform_drv_probe+0x48/0x94)

Fix this by splitting the cleanup block, and adding a missing call to
gpiochip_irqchip_remove().

Fixes: 28355f81969962cf ("gpio: defer probe if pinctrl cannot be found")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

drm/vmwgfx: Fix dma API layer violation

Remove the check for IOMMU presence since it was considered a
layer violation.
This means we have no reliable way to destinguish between coherent
hardware IOMMU DMA address translations and incoherent SWIOTLB DMA
address translations, which we can't handle. So always presume the
former. This means that if anybody forces SWIOTLB without also setting
the vmw_force_coherent=1 vmwgfx option, driver operation will fail,
like it will on most other graphics drivers.

Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>

perf/x86/intel: Update KBL Package C-state events to also include PC8/PC9/PC10 counters

Kaby Lake (and Coffee Lake) has PC8/PC9/PC10 residency counters.

This patch updates the list of Kaby/Coffee Lake PMU event counters
from the snb_cstates[] list of events to the hswult_cstates[]
list of events, which keeps all previously supported events and
also adds the PKG_C8, PKG_C9 and PKG_C10 residency counters.

This allows user space tools to profile them through the perf interface.

Signed-off-by: Harry Pan <harry.pan@intel.com>
Cc: <stable@vger.kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: gs0622@gmail.com
Link: http://lkml.kernel.org/r/20190424145033.1924-1-harry.pan@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>

Merge git://git./linux/kernel/git/davem/net

Pull networking fixes from David Miller:
"Just the usual assortment of small'ish fixes:

   1) Conntrack timeout is sometimes not initialized properly, from
      Alexander Potapenko.

   2) Add a reasonable range limit to tcp_min_rtt_wlen to avoid
      undefined behavior. From ZhangXiaoxu.

   3) des1 field of descriptor in stmmac driver is initialized with the
      wrong variable. From Yue Haibing.

   4) Increase mlxsw pci sw reset timeout a little bit more, from Ido
      Schimmel.

   5) Match IOT2000 stmmac devices more accurately, from Su Bao Cheng.

   6) Fallback refcount fix in TLS code, from Jakub Kicinski.

   7) Fix max MTU check when using XDP in mlx5, from Maxim Mikityanskiy.

   8) Fix recursive locking in team driver, from Hangbin Liu.

   9) Fix tls_set_device_offload_Rx() deadlock, from Jakub Kicinski.

  10) Don't use napi_alloc_frag() outside of softiq context of socionext
      driver, from Ilias Apalodimas.

  11) MAC address increment overflow in ncsi, from Tao Ren.

  12) Fix a regression in 8K/1M pool switching of RDS, from Zhu Yanjun.

  13) ipv4_link_failure has to validate the headers that are actually
      there because RAW sockets can pass in arbitrary garbage, from Eric
      Dumazet"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
  ipv4: add sanity checks in ipv4_link_failure()
  net/rose: fix unbound loop in rose_loopback_timer()
  rxrpc: fix race condition in rxrpc_input_packet()
  net: rds: exchange of 8K and 1M pool
  net: vrf: Fix operation not supported when set vrf mac
  net/ncsi: handle overflow when incrementing mac address
  net: socionext: replace napi_alloc_frag with the netdev variant on init
  net: atheros: fix spelling mistake "underun" -> "underrun"
  spi: ST ST95HF NFC: declare missing of table
  spi: Micrel eth switch: declare missing of table
  net: stmmac: move stmmac_check_ether_addr() to driver probe
  netfilter: fix nf_l4proto_log_invalid to log invalid packets
  netfilter: never get/set skb->tstamp
  netfilter: ebtables: CONFIG_COMPAT: drop a bogus WARN_ON
  Documentation: decnet: remove reference to CONFIG_DECNET_ROUTE_FWMARK
  dt-bindings: add an explanation for internal phy-mode
  net/tls: don't leak IV and record seq when offload fails
  net/tls: avoid potential deadlock in tls_set_device_offload_rx()
  selftests/net: correct the return value for run_afpackettests
  team: fix possible recursive locking when add slaves
  ...

Merge tag 'leds-for-5.1-rc7' of git://git./linux/kernel/git/j.anaszewski/linux-leds

Pull LED update from Jacek Anaszewski:
"A single change to MAINTAINERS:

We announce a new LED reviewer - Dan Murphy"

* tag 'leds-for-5.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
MAINTAINERS: LEDs: Add designated reviewer for LED subsystem

ipv4: add sanity checks in ipv4_link_failure()

Before calling __ip_options_compile(), we need to ensure the network
header is a an IPv4 one, and that it is already pulled in skb->head.

RAW sockets going through a tunnel can end up calling ipv4_link_failure()
with total garbage in the skb, or arbitrary lengthes.

syzbot report :

BUG: KASAN: stack-out-of-bounds in memcpy include/linux/string.h:355 [inline]
BUG: KASAN: stack-out-of-bounds in __ip_options_echo+0x294/0x1120 net/ipv4/ip_options.c:123
Write of size 69 at addr ffff888096abf068 by task syz-executor.4/9204

CPU: 0 PID: 9204 Comm: syz-executor.4 Not tainted 5.1.0-rc5+ #77
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x172/0x1f0 lib/dump_stack.c:113
print_address_description.cold+0x7c/0x20d mm/kasan/report.c:187
kasan_report.cold+0x1b/0x40 mm/kasan/report.c:317
check_memory_region_inline mm/kasan/generic.c:185 [inline]
check_memory_region+0x123/0x190 mm/kasan/generic.c:191
memcpy+0x38/0x50 mm/kasan/common.c:133
memcpy include/linux/string.h:355 [inline]
__ip_options_echo+0x294/0x1120 net/ipv4/ip_options.c:123
__icmp_send+0x725/0x1400 net/ipv4/icmp.c:695
ipv4_link_failure+0x29f/0x550 net/ipv4/route.c:1204
dst_link_failure include/net/dst.h:427 [inline]
vti6_xmit net/ipv6/ip6_vti.c:514 [inline]
vti6_tnl_xmit+0x10d4/0x1c0c net/ipv6/ip6_vti.c:553
__netdev_start_xmit include/linux/netdevice.h:4414 [inline]
netdev_start_xmit include/linux/netdevice.h:4423 [inline]
xmit_one net/core/dev.c:3292 [inline]
dev_hard_start_xmit+0x1b2/0x980 net/core/dev.c:3308
__dev_queue_xmit+0x271d/0x3060 net/core/dev.c:3878
dev_queue_xmit+0x18/0x20 net/core/dev.c:3911
neigh_direct_output+0x16/0x20 net/core/neighbour.c:1527
neigh_output include/net/neighbour.h:508 [inline]
ip_finish_output2+0x949/0x1740 net/ipv4/ip_output.c:229
ip_finish_output+0x73c/0xd50 net/ipv4/ip_output.c:317
NF_HOOK_COND include/linux/netfilter.h:278 [inline]
ip_output+0x21f/0x670 net/ipv4/ip_output.c:405
dst_output include/net/dst.h:444 [inline]
NF_HOOK include/linux/netfilter.h:289 [inline]
raw_send_hdrinc net/ipv4/raw.c:432 [inline]
raw_sendmsg+0x1d2b/0x2f20 net/ipv4/raw.c:663
inet_sendmsg+0x147/0x5d0 net/ipv4/af_inet.c:798
sock_sendmsg_nosec net/socket.c:651 [inline]
sock_sendmsg+0xdd/0x130 net/socket.c:661
sock_write_iter+0x27c/0x3e0 net/socket.c:988
call_write_iter include/linux/fs.h:1866 [inline]
new_sync_write+0x4c7/0x760 fs/read_write.c:474
__vfs_write+0xe4/0x110 fs/read_write.c:487
vfs_write+0x20c/0x580 fs/read_write.c:549
ksys_write+0x14f/0x2d0 fs/read_write.c:599
__do_sys_write fs/read_write.c:611 [inline]
__se_sys_write fs/read_write.c:608 [inline]
__x64_sys_write+0x73/0xb0 fs/read_write.c:608
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x458c29
Code: ad b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007f293b44bc78 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 0000000000458c29
RDX: 0000000000000014 RSI: 00000000200002c0 RDI: 0000000000000003
RBP: 000000000073bf00 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f293b44c6d4
R13: 00000000004c8623 R14: 00000000004ded68 R15: 00000000ffffffff

The buggy address belongs to the page:
page:ffffea00025aafc0 count:0 mapcount:0 mapping:0000000000000000 index:0x0
flags: 0x1fffc0000000000()
raw: 01fffc0000000000 0000000000000000 ffffffff025a0101 0000000000000000
raw: 0000000000000000 0000000000000000 00000000ffffffff 0000000000000000
page dumped because: kasan: bad access detected

Memory state around the buggy address:
ffff888096abef80: 00 00 00 f2 f2 f2 f2 f2 00 00 00 00 00 00 00 f2
ffff888096abf000: f2 f2 f2 f2 00 00 00 00 00 00 00 00 00 00 00 00
>ffff888096abf080: 00 00 f3 f3 f3 f3 00 00 00 00 00 00 00 00 00 00
^
ffff888096abf100: 00 00 00 00 f1 f1 f1 f1 00 00 f3 f3 00 00 00 00
ffff888096abf180: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Fixes: ed0de45a1008 ("ipv4: recompile ip options in ipv4_link_failure")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Stephen Suryaputra <ssuryaextr@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/rose: fix unbound loop in rose_loopback_timer()

This patch adds a limit on the number of skbs that fuzzers can queue
into loopback_queue. 1000 packets for rose loopback seems more than enough.

Then, since we now have multiple cpus in most linux hosts,
we also need to limit the number of skbs rose_loopback_timer()
can dequeue at each round.

rose_loopback_queue() can be drop-monitor friendly, calling
consume_skb() or kfree_skb() appropriately.

Finally, use mod_timer() instead of del_timer() + add_timer()

syzbot report was :

rcu: INFO: rcu_preempt self-detected stall on CPU
rcu:    0-...!: (10499 ticks this GP) idle=536/1/0x4000000000000002 softirq=103291/103291 fqs=34
rcu:     (t=10500 jiffies g=140321 q=323)
rcu: rcu_preempt kthread starved for 10426 jiffies! g140321 f0x0 RCU_GP_WAIT_FQS(5) ->state=0x402 ->cpu=1
rcu: RCU grace-period kthread stack dump:
rcu_preempt     I29168    10      2 0x80000000
Call Trace:
context_switch kernel/sched/core.c:2877 [inline]
__schedule+0x813/0x1cc0 kernel/sched/core.c:3518
schedule+0x92/0x180 kernel/sched/core.c:3562
schedule_timeout+0x4db/0xfd0 kernel/time/timer.c:1803
rcu_gp_fqs_loop kernel/rcu/tree.c:1971 [inline]
rcu_gp_kthread+0x962/0x17b0 kernel/rcu/tree.c:2128
kthread+0x357/0x430 kernel/kthread.c:253
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352
NMI backtrace for cpu 0
CPU: 0 PID: 7632 Comm: kworker/0:4 Not tainted 5.1.0-rc5+ #172
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: events iterate_cleanup_work
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x172/0x1f0 lib/dump_stack.c:113
nmi_cpu_backtrace.cold+0x63/0xa4 lib/nmi_backtrace.c:101
nmi_trigger_cpumask_backtrace+0x1be/0x236 lib/nmi_backtrace.c:62
arch_trigger_cpumask_backtrace+0x14/0x20 arch/x86/kernel/apic/hw_nmi.c:38
trigger_single_cpu_backtrace include/linux/nmi.h:164 [inline]
rcu_dump_cpu_stacks+0x183/0x1cf kernel/rcu/tree.c:1223
print_cpu_stall kernel/rcu/tree.c:1360 [inline]
check_cpu_stall kernel/rcu/tree.c:1434 [inline]
rcu_pending kernel/rcu/tree.c:3103 [inline]
rcu_sched_clock_irq.cold+0x500/0xa4a kernel/rcu/tree.c:2544
update_process_times+0x32/0x80 kernel/time/timer.c:1635
tick_sched_handle+0xa2/0x190 kernel/time/tick-sched.c:161
tick_sched_timer+0x47/0x130 kernel/time/tick-sched.c:1271
__run_hrtimer kernel/time/hrtimer.c:1389 [inline]
__hrtimer_run_queues+0x33e/0xde0 kernel/time/hrtimer.c:1451
hrtimer_interrupt+0x314/0x770 kernel/time/hrtimer.c:1509
local_apic_timer_interrupt arch/x86/kernel/apic/apic.c:1035 [inline]
smp_apic_timer_interrupt+0x120/0x570 arch/x86/kernel/apic/apic.c:1060
apic_timer_interrupt+0xf/0x20 arch/x86/entry/entry_64.S:807
RIP: 0010:__sanitizer_cov_trace_pc+0x0/0x50 kernel/kcov.c:95
Code: 89 25 b4 6e ec 08 41 bc f4 ff ff ff e8 cd 5d ea ff 48 c7 05 9e 6e ec 08 00 00 00 00 e9 a4 e9 ff ff 90 90 90 90 90 90 90 90 90 <55> 48 89 e5 48 8b 75 08 65 48 8b 04 25 00 ee 01 00 65 8b 15 c8 60
RSP: 0018:ffff8880ae807ce0 EFLAGS: 00000286 ORIG_RAX: ffffffffffffff13
RAX: ffff88806fd40640 RBX: dffffc0000000000 RCX: ffffffff863fbc56
RDX: 0000000000000100 RSI: ffffffff863fbc1d RDI: ffff88808cf94228
RBP: ffff8880ae807d10 R08: ffff88806fd40640 R09: ffffed1015d00f8b
R10: ffffed1015d00f8a R11: 0000000000000003 R12: ffff88808cf941c0
R13: 00000000fffff034 R14: ffff8882166cd840 R15: 0000000000000000
rose_loopback_timer+0x30d/0x3f0 net/rose/rose_loopback.c:91
call_timer_fn+0x190/0x720 kernel/time/timer.c:1325
expire_timers kernel/time/timer.c:1362 [inline]
__run_timers kernel/time/timer.c:1681 [inline]
__run_timers kernel/time/timer.c:1649 [inline]
run_timer_softirq+0x652/0x1700 kernel/time/timer.c:1694
__do_softirq+0x266/0x95a kernel/softirq.c:293
do_softirq_own_stack+0x2a/0x40 arch/x86/entry/entry_64.S:1027

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rxrpc: fix race condition in rxrpc_input_packet()

After commit 5271953cad31 ("rxrpc: Use the UDP encap_rcv hook"),
rxrpc_input_packet() is directly called from lockless UDP receive
path, under rcu_read_lock() protection.

It must therefore use RCU rules :

- udp_sk->sk_user_data can be cleared at any point in this function.
  rcu_dereference_sk_user_data() is what we need here.

- Also, since sk_user_data might have been set in rxrpc_open_socket()
  we must observe a proper RCU grace period before kfree(local) in
  rxrpc_lookup_local()

v4: @local can be NULL in xrpc_lookup_local() as reported by kbuild test robot <lkp@intel.com>
        and Julia Lawall <julia.lawall@lip6.fr>, thanks !

v3,v2 : addressed David Howells feedback, thanks !

syzbot reported :

kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] PREEMPT SMP KASAN
CPU: 0 PID: 19236 Comm: syz-executor703 Not tainted 5.1.0-rc6 #79
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:__lock_acquire+0xbef/0x3fb0 kernel/locking/lockdep.c:3573
Code: 00 0f 85 a5 1f 00 00 48 81 c4 10 01 00 00 5b 41 5c 41 5d 41 5e 41 5f 5d c3 48 b8 00 00 00 00 00 fc ff df 4c 89 ea 48 c1 ea 03 <80> 3c 02 00 0f 85 4a 21 00 00 49 81 7d 00 20 54 9c 89 0f 84 cf f4
RSP: 0018:ffff88809d7aef58 EFLAGS: 00010002
RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000026 RSI: 0000000000000000 RDI: 0000000000000001
RBP: ffff88809d7af090 R08: 0000000000000001 R09: 0000000000000001
R10: ffffed1015d05bc7 R11: ffff888089428600 R12: 0000000000000000
R13: 0000000000000130 R14: 0000000000000001 R15: 0000000000000001
FS:  00007f059044d700(0000) GS:ffff8880ae800000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000004b6040 CR3: 00000000955ca000 CR4: 00000000001406f0
Call Trace:
lock_acquire+0x16f/0x3f0 kernel/locking/lockdep.c:4211
__raw_spin_lock_irqsave include/linux/spinlock_api_smp.h:110 [inline]
_raw_spin_lock_irqsave+0x95/0xcd kernel/locking/spinlock.c:152
skb_queue_tail+0x26/0x150 net/core/skbuff.c:2972
rxrpc_reject_packet net/rxrpc/input.c:1126 [inline]
rxrpc_input_packet+0x4a0/0x5536 net/rxrpc/input.c:1414
udp_queue_rcv_one_skb+0xaf2/0x1780 net/ipv4/udp.c:2011
udp_queue_rcv_skb+0x128/0x730 net/ipv4/udp.c:2085
udp_unicast_rcv_skb.isra.0+0xb9/0x360 net/ipv4/udp.c:2245
__udp4_lib_rcv+0x701/0x2ca0 net/ipv4/udp.c:2301
udp_rcv+0x22/0x30 net/ipv4/udp.c:2482
ip_protocol_deliver_rcu+0x60/0x8f0 net/ipv4/ip_input.c:208
ip_local_deliver_finish+0x23b/0x390 net/ipv4/ip_input.c:234
NF_HOOK include/linux/netfilter.h:289 [inline]
NF_HOOK include/linux/netfilter.h:283 [inline]
ip_local_deliver+0x1e9/0x520 net/ipv4/ip_input.c:255
dst_input include/net/dst.h:450 [inline]
ip_rcv_finish+0x1e1/0x300 net/ipv4/ip_input.c:413
NF_HOOK include/linux/netfilter.h:289 [inline]
NF_HOOK include/linux/netfilter.h:283 [inline]
ip_rcv+0xe8/0x3f0 net/ipv4/ip_input.c:523
__netif_receive_skb_one_core+0x115/0x1a0 net/core/dev.c:4987
__netif_receive_skb+0x2c/0x1c0 net/core/dev.c:5099
netif_receive_skb_internal+0x117/0x660 net/core/dev.c:5202
napi_frags_finish net/core/dev.c:5769 [inline]
napi_gro_frags+0xade/0xd10 net/core/dev.c:5843
tun_get_user+0x2f24/0x3fb0 drivers/net/tun.c:1981
tun_chr_write_iter+0xbd/0x156 drivers/net/tun.c:2027
call_write_iter include/linux/fs.h:1866 [inline]
do_iter_readv_writev+0x5e1/0x8e0 fs/read_write.c:681
do_iter_write fs/read_write.c:957 [inline]
do_iter_write+0x184/0x610 fs/read_write.c:938
vfs_writev+0x1b3/0x2f0 fs/read_write.c:1002
do_writev+0x15e/0x370 fs/read_write.c:1037
__do_sys_writev fs/read_write.c:1110 [inline]
__se_sys_writev fs/read_write.c:1107 [inline]
__x64_sys_writev+0x75/0xb0 fs/read_write.c:1107
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe

Fixes: 5271953cad31 ("rxrpc: Use the UDP encap_rcv hook")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MAINTAINERS: LEDs: Add designated reviewer for LED subsystem

Add a designated reviewer for the LED subsystem as there
are already two maintainers assigned.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>

net: rds: exchange of 8K and 1M pool

Before the commit 490ea5967b0d ("RDS: IB: move FMR code to its own file"),
when the dirty_count is greater than 9/10 of max_items of 8K pool,
1M pool is used, Vice versa. After the commit 490ea5967b0d ("RDS: IB: move
FMR code to its own file"), the above is removed. When we make the
following tests.

Server:
  rds-stress -r 1.1.1.16 -D 1M

Client:
  rds-stress -r 1.1.1.14 -s 1.1.1.16 -D 1M

The following will appear.
"
connecting to 1.1.1.16:4000
negotiated options, tasks will start in 2 seconds
Starting up..header from 1.1.1.166:4001 to id 4001 bogus
..
tsks  tx/s  rx/s tx+rx K/s  mbi K/s  mbo K/s tx us/c  rtt us
cpu %
   1    0    0     0.00     0.00     0.00    0.00 0.00 -1.00
   1    0    0     0.00     0.00     0.00    0.00 0.00 -1.00
   1    0    0     0.00     0.00     0.00    0.00 0.00 -1.00
   1    0    0     0.00     0.00     0.00    0.00 0.00 -1.00
   1    0    0     0.00     0.00     0.00    0.00 0.00 -1.00
...
"
So this exchange between 8K and 1M pool is added back.

Fixes: commit 490ea5967b0d ("RDS: IB: move FMR code to its own file")
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: vrf: Fix operation not supported when set vrf mac

Vrf device is not able to change mac address now because lack of
ndo_set_mac_address. Complete this in case some apps need to do
this.

Reported-by: Hui Wang <wanghui104@huawei.com>
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cifs: fix page reference leak with readv/writev

CIFS can leak pages reference gotten through GUP (get_user_pages*()
through iov_iter_get_pages()). This happen if cifs_send_async_read()
or cifs_write_from_iter() calls fail from within __cifs_readv() and
__cifs_writev() respectively. This patch move page unreference to
cifs_aio_ctx_release() which will happens on all code paths this is
all simpler to follow for correctness.

Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Cc: Steve French <sfrench@samba.org>
Cc: linux-cifs@vger.kernel.org
Cc: samba-technical@lists.samba.org
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: linux-fsdevel@vger.kernel.org
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>

cifs: do not attempt cifs operation on smb2+ rename error

A path-based rename returning EBUSY will incorrectly try opening
the file with a cifs (NT Create AndX) operation on an smb2+ mount,
which causes the server to force a session close.

If the mount is smb2+, skip the fallback.

Signed-off-by: Frank Sorenson <sorenson@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
CC: Stable <stable@vger.kernel.org>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>

cifs: fix memory leak in SMB2_read

Commit 088aaf17aa79300cab14dbee2569c58cfafd7d6e introduced a leak where
if SMB2_read() returned an error we would return without freeing the
request buffer.

Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>

Input: synaptics-rmi4 - fix possible double free

The RMI4 function structure has been released in rmi_register_function
if error occurs. However, it will be released again in the function
rmi_create_function, which may result in a double-free bug.

Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

RDMA/ucontext: Fix regression with disassociate

When this code was consolidated the intention was that the VMA would
become backed by anonymous zero pages after the zap_vma_pte - however this
very subtly relied on setting the vm_ops = NULL and clearing the VM_SHARED
bits to transform the VMA into an anonymous VMA. Since the vm_ops was
removed this broke.

Now userspace gets a SIGBUS if it touches the vma after disassociation.

Instead of converting the VMA to anonymous provide a fault handler that
puts a zero'd page into the VMA when user-space touches it after
disassociation.

Cc: stable@vger.kernel.org
Suggested-by: Andrea Arcangeli <aarcange@redhat.com>
Fixes: 5f9794dc94f5 ("RDMA/ucontext: Add a core API for mmaping driver IO memory")
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>

Input: snvs_pwrkey - make it depend on ARCH_MXC

The SNVS power key is not only used on i.MX6SX and i.MX7D, it is also
used by i.MX6UL and NXP's latest ARMv8 based i.MX8M series SOC. So
update the config dependency to use ARCH_MXC, and add the COMPILE_TEST
too.

Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

RDMA/mlx5: Use rdma_user_map_io for mapping BAR pages

Since mlx5 supports device disassociate it must use this API for all
BAR page mmaps, otherwise the pages can remain mapped after the device
is unplugged causing a system crash.

Cc: stable@vger.kernel.org
Fixes: 5f9794dc94f5 ("RDMA/ucontext: Add a core API for mmaping driver IO memory")
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Reviewed-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>

RDMA/mlx5: Do not allow the user to write to the clock page

The intent of this VMA was to be read-only from user space, but the
VM_MAYWRITE masking was missed, so mprotect could make it writable.

Cc: stable@vger.kernel.org
Fixes: 5c99eaecb1fc ("IB/mlx5: Mmap the HCA's clock info to user-space")
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Reviewed-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>

drm/vc4: Fix compilation error reported by kbuild test bot

A pointer to crtc was missing, resulting in the following build error:
drivers/gpu/drm/vc4/vc4_crtc.c:1045:44: sparse: sparse: incorrect type in argument 1 (different base types)
drivers/gpu/drm/vc4/vc4_crtc.c:1045:44: sparse: expected struct drm_crtc *crtc
drivers/gpu/drm/vc4/vc4_crtc.c:1045:44: sparse: got struct drm_crtc_state *state
drivers/gpu/drm/vc4/vc4_crtc.c:1045:39: sparse: sparse: not enough arguments for function vc4_crtc_destroy_state

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reported-by: kbuild test robot <lkp@intel.com>
Cc: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/2b6ed5e6-81b0-4276-8860-870b54ca3262@linux.intel.com
Fixes: d08106796a78 ("drm/vc4: Fix memory leak during gpu reset.")
Cc: <stable@vger.kernel.org> # v4.6+
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/sun4i: Unbind components before releasing DRM and memory

Our components may still be using the DRM device driver (if only to
access our driver's private data), so make sure to unbind them before
the final drm_dev_put.

Also release our reserved memory after component unbind instead of
before to match reverse creation order.

Fixes: f5a9ed867c83 ("drm/sun4i: Fix component unbinding and component master deletion")
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190424090413.6918-1-paul.kocialkowski@bootlin.com