sfrench/cifs-2.6.git
11 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wirel...
David S. Miller [Mon, 19 Jul 2010 19:38:51 +0000 (12:38 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6

11 years agoIPv6: fix CoA check in RH2 input handler (mip6_rthdr_input())
Arnaud Ebalard [Fri, 16 Jul 2010 00:38:44 +0000 (00:38 +0000)]
IPv6: fix CoA check in RH2 input handler (mip6_rthdr_input())

The input handler for Type 2 Routing Header (mip6_rthdr_input())
checks if the CoA in the packet matches the CoA in the XFRM state.

Current check is buggy: it compares the adddress in the Type 2
Routing Header, i.e. the HoA, against the expected CoA in the state.
The comparison should be made against the address in the destination
field of the IPv6 header.

The bug remained unnoticed because the main (and possibly only current)
user of the code (UMIP MIPv6 Daemon) initializes the XFRM state with the
unspecified address, i.e. explicitly allows everything.

Yoshifuji-san, can you ack that one?

Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoibmveth: lost IRQ while closing/opening device leads to service loss
Robert Jennings [Fri, 16 Jul 2010 04:57:25 +0000 (04:57 +0000)]
ibmveth: lost IRQ while closing/opening device leads to service loss

The order of freeing the IRQ and freeing the device in firmware
in ibmveth_close can cause the adapter to become unusable after a
subsequent ibmveth_open.  Only a reboot of the OS will make the
network device usable again. This is seen when cycling the adapter
up and down while there is network activity.

There is a window where an IRQ will be left unserviced (H_EOI will not
be called).  The solution is to make a VIO_IRQ_DISABLE h_call, free the
device with firmware, and then call free_irq.

Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoMerge branch 'vhost-net' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
David S. Miller [Fri, 16 Jul 2010 19:41:44 +0000 (12:41 -0700)]
Merge branch 'vhost-net' of git://git./linux/kernel/git/mst/vhost

11 years agort2x00: Fix lockdep warning in rt2x00lib_probe_dev()
Stephen Boyd [Fri, 16 Jul 2010 16:50:10 +0000 (09:50 -0700)]
rt2x00: Fix lockdep warning in rt2x00lib_probe_dev()

The rt2x00dev->intf_work workqueue is never initialized when a driver is
probed for a non-existent device (in this case rt2500usb). On such a
path we call rt2x00lib_remove_dev() to free any resources initialized
during the probe before we use INIT_WORK to initialize the workqueue.
This causes lockdep to get confused since the lock used in the workqueue
hasn't been initialized yet but is now being acquired during
cancel_work_sync() called by rt2x00lib_remove_dev().

Fix this by initializing the workqueue first before we attempt to probe
the device. This should make lockdep happy and avoid breaking any
assumptions about how the library cleans up after a probe fails.

phy0 -> rt2x00lib_probe_dev: Error - Failed to allocate device.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
Pid: 2027, comm: modprobe Not tainted 2.6.35-rc5+ #60
Call Trace:
 [<ffffffff8105fe59>] register_lock_class+0x152/0x31f
 [<ffffffff81344a00>] ? usb_control_msg+0xd5/0x111
 [<ffffffff81061bde>] __lock_acquire+0xce/0xcf4
 [<ffffffff8105f6fd>] ? trace_hardirqs_off+0xd/0xf
 [<ffffffff81492aef>] ?  _raw_spin_unlock_irqrestore+0x33/0x41
 [<ffffffff810628d5>] lock_acquire+0xd1/0xf7
 [<ffffffff8104f037>] ? __cancel_work_timer+0x99/0x17e
 [<ffffffff8104f06e>] __cancel_work_timer+0xd0/0x17e
 [<ffffffff8104f037>] ? __cancel_work_timer+0x99/0x17e
 [<ffffffff8104f136>] cancel_work_sync+0xb/0xd
 [<ffffffffa0096675>] rt2x00lib_remove_dev+0x25/0xb0 [rt2x00lib]
 [<ffffffffa0096bf7>] rt2x00lib_probe_dev+0x380/0x3ed [rt2x00lib]
 [<ffffffff811d78a7>] ? __raw_spin_lock_init+0x31/0x52
 [<ffffffffa00bbd2c>] ? T.676+0xe/0x10 [rt2x00usb]
 [<ffffffffa00bbe4f>] rt2x00usb_probe+0x121/0x15e [rt2x00usb]
 [<ffffffff813468bd>] usb_probe_interface+0x151/0x19e
 [<ffffffff812ea08e>] driver_probe_device+0xa7/0x136
 [<ffffffff812ea167>] __driver_attach+0x4a/0x66
 [<ffffffff812ea11d>] ? __driver_attach+0x0/0x66
 [<ffffffff812e96ca>] bus_for_each_dev+0x54/0x89
 [<ffffffff812e9efd>] driver_attach+0x19/0x1b
 [<ffffffff812e9b64>] bus_add_driver+0xb4/0x204
 [<ffffffff812ea41b>] driver_register+0x98/0x109
 [<ffffffff813465dd>] usb_register_driver+0xb2/0x173
 [<ffffffffa00ca000>] ? rt2500usb_init+0x0/0x20 [rt2500usb]
 [<ffffffffa00ca01e>] rt2500usb_init+0x1e/0x20 [rt2500usb]
 [<ffffffff81000203>] do_one_initcall+0x6d/0x17a
 [<ffffffff8106cae8>] sys_init_module+0x9c/0x1e0
 [<ffffffff8100296b>] system_call_fastpath+0x16/0x1b

Signed-off-by: Stephen Boyd <bebarino@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agovhost: avoid pr_err on condition guest can trigger
Michael S. Tsirkin [Thu, 24 Jun 2010 14:10:25 +0000 (17:10 +0300)]
vhost: avoid pr_err on condition guest can trigger

Guest can trigger packet truncation by posting
a very short buffer and disabling buffer merging.
Convert pr_err to pr_debug to avoid log from filling
up when this happens.

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
11 years agoipmr: Don't leak memory if fib lookup fails.
Ben Greear [Thu, 15 Jul 2010 13:22:33 +0000 (13:22 +0000)]
ipmr: Don't leak memory if fib lookup fails.

This was detected using two mcast router tables.  The
pimreg for the second interface did not have a specific
mrule, so packets received by it were handled by the
default table, which had nothing configured.

This caused the ipmr_fib_lookup to fail, causing
the memory leak.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agovhost-net: avoid flush under lock
Michael S. Tsirkin [Thu, 15 Jul 2010 12:19:12 +0000 (15:19 +0300)]
vhost-net: avoid flush under lock

We flush under vq mutex when changing backends.
This creates a deadlock as workqueue being flushed
needs this lock as well.

https://bugzilla.redhat.com/show_bug.cgi?id=612421

Drop the vq mutex before flush: we have the device mutex
which is sufficient to prevent another ioctl from touching
the vq.

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
11 years agonet: fix problem in reading sock TX queue
Tom Herbert [Thu, 15 Jul 2010 03:50:29 +0000 (20:50 -0700)]
net: fix problem in reading sock TX queue

Fix problem in reading the tx_queue recorded in a socket.  In
dev_pick_tx, the TX queue is read by doing a check with
sk_tx_queue_recorded on the socket, followed by a sk_tx_queue_get.
The problem is that there is not mutual exclusion across these
calls in the socket so it it is possible that the queue in the
sock can be invalidated after sk_tx_queue_recorded is called so
that sk_tx_queue get returns -1, which sets 65535 in queue_index
and thus dev_pick_tx returns 65536 which is a bogus queue and
can cause crash in dev_queue_xmit.

We fix this by only calling sk_tx_queue_get which does the proper
checks.  The interface is that sk_tx_queue_get returns the TX queue
if the sock argument is non-NULL and TX queue is recorded, else it
returns -1.  sk_tx_queue_recorded is no longer used so it can be
completely removed.

Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agonet/core: neighbour update Oops
Doug Kehn [Thu, 15 Jul 2010 01:02:16 +0000 (18:02 -0700)]
net/core: neighbour update Oops

When configuring DMVPN (GRE + openNHRP) and a GRE remote
address is configured a kernel Oops is observed.  The
obserseved Oops is caused by a NULL header_ops pointer
(neigh->dev->header_ops) in neigh_update_hhs() when

void (*update)(struct hh_cache*, const struct net_device*, const unsigned char *)
= neigh->dev->header_ops->cache_update;

is executed.  The dev associated with the NULL header_ops is
the GRE interface.  This patch guards against the
possibility that header_ops is NULL.

This Oops was first observed in kernel version 2.6.26.8.

Signed-off-by: Doug Kehn <rdkehn@yahoo.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agonet: skb_tx_hash() fix relative to skb_orphan_try()
Eric Dumazet [Tue, 13 Jul 2010 05:24:20 +0000 (05:24 +0000)]
net: skb_tx_hash() fix relative to skb_orphan_try()

commit fc6055a5ba31e2 (net: Introduce skb_orphan_try()) added early
orphaning of skbs.

This unfortunately added a performance regression in skb_tx_hash() in
case of stacked devices (bonding, vlans, ...)

Since skb->sk is now NULL, we cannot access sk->sk_hash anymore to
spread tx packets to multiple NIC queues on multiqueue devices.

skb_tx_hash() in this case only uses skb->protocol, same value for all
flows.

skb_orphan_try() can copy sk->sk_hash into skb->rxhash and skb_tx_hash()
can use this saved sk_hash value to compute its internal hash value.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agorfs: call sock_rps_record_flow() in tcp_splice_read()
Changli Gao [Mon, 12 Jul 2010 21:00:12 +0000 (21:00 +0000)]
rfs: call sock_rps_record_flow() in tcp_splice_read()

rfs: call sock_rps_record_flow() in tcp_splice_read()

call sock_rps_record_flow() in tcp_splice_read(), so the applications using
splice(2) or sendfile(2) can utilize RFS.

Signed-off-by: Changli Gao <xiaosuo@gmail.com>
----
 net/ipv4/tcp.c |    1 +
 1 file changed, 1 insertion(+)
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoxfrm: do not assume that template resolving always returns xfrms
Timo Teräs [Mon, 12 Jul 2010 21:29:42 +0000 (21:29 +0000)]
xfrm: do not assume that template resolving always returns xfrms

xfrm_resolve_and_create_bundle() assumed that, if policies indicated
presence of xfrms, bundle template resolution would always return
some xfrms. This is not true for 'use' level policies which can
result in no xfrm's being applied if there is no suitable xfrm states.
This fixes a crash by this incorrect assumption.

Reported-by: George Spelvin <linux@horizon.com>
Bisected-by: George Spelvin <linux@horizon.com>
Tested-by: George Spelvin <linux@horizon.com>
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agohostap_pci: set dev->base_addr during probe
John W. Linville [Tue, 13 Jul 2010 18:06:32 +0000 (14:06 -0400)]
hostap_pci: set dev->base_addr during probe

"hostap: Protect against initialization interrupt" (which reinstated
"wireless: hostap, fix oops due to early probing interrupt")
reintroduced Bug 16111.  This is because hostap_pci wasn't setting
dev->base_addr, which is now checked in prism2_interrupt.  As a result,
initialization was failing for PCI-based hostap devices.  This corrects
that oversight.

Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agoaxnet_cs: use spin_lock_irqsave in ax_interrupt
Ken Kawasaki [Sat, 10 Jul 2010 01:18:13 +0000 (01:18 +0000)]
axnet_cs: use spin_lock_irqsave in ax_interrupt

Use spin_lock_irqsave instead of spin_lock in ax_interrupt because
the interrupt handler can also be invoked from ei_watchdog.

Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agodsa: Fix Kconfig dependencies.
David S. Miller [Tue, 13 Jul 2010 03:03:42 +0000 (20:03 -0700)]
dsa: Fix Kconfig dependencies.

Based upon a report by Randy Dunlap.

DSA needs PHYLIB, but PHYLIB needs NET_ETHERNET.  So, in order
to select PHYLIB we have to make DSA depend upon NET_ETHERNET.

Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoact_nat: not all of the ICMP packets need an IP header payload
Changli Gao [Fri, 9 Jul 2010 15:33:25 +0000 (15:33 +0000)]
act_nat: not all of the ICMP packets need an IP header payload

not all of the ICMP packets need an IP header payload, so we check the length
of the skbs only when the packets should have an IP header payload.

Based upon analysis and initial patch by Rodrigo Partearroyo González.

Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
----
 net/sched/act_nat.c |    5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wirel...
David S. Miller [Mon, 12 Jul 2010 22:17:29 +0000 (15:17 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6

11 years agor8169: incorrect identifier for a 8168dp
Francois Romieu [Mon, 12 Jul 2010 00:10:09 +0000 (17:10 -0700)]
r8169: incorrect identifier for a 8168dp

Merge error.

See CFG_METHOD_8 (0x3c800000 + 0x00300000) since version 8.002.00
of Realtek's driver.

Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoPhonet: fix skb leak in pipe endpoint accept()
Rémi Denis-Courmont [Wed, 7 Jul 2010 20:56:53 +0000 (20:56 +0000)]
Phonet: fix skb leak in pipe endpoint accept()

Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoBluetooth: Update sec_level/auth_type for already existing connections
Ville Tervo [Tue, 15 Jun 2010 12:56:05 +0000 (15:56 +0300)]
Bluetooth: Update sec_level/auth_type for already existing connections

Update auth level for already existing connections if it is lower
than required by new connection.

Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Reviewed-by: Emeltchenko Andrei <andrei.emeltchenko@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
11 years agoBluetooth: Reset the security level after an authentication failure
Johan Hedberg [Fri, 18 Jun 2010 08:08:56 +0000 (11:08 +0300)]
Bluetooth: Reset the security level after an authentication failure

When authentication fails for a connection the assumed security level
should be set back to BT_SECURITY_LOW so that subsequent connect
attempts over the same link don't falsely assume that security is
adequate enough.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
11 years agoBluetooth: Check L2CAP pending status before sending connect request
Andrei Emeltchenko [Thu, 8 Jul 2010 09:14:41 +0000 (12:14 +0300)]
Bluetooth: Check L2CAP pending status before sending connect request

Due to race condition in L2CAP state machine L2CAP Connection Request
may be sent twice for SDP with the same source channel id. Problems
reported connecting to Apple products, some carkit, Blackberry phones.

...
2010-06-07 21:18:03.651031 < ACL data: handle 1 flags 0x02 dlen 12
    L2CAP(s): Connect req: psm 1 scid 0x0040
2010-06-07 21:18:03.653473 > HCI Event: Number of Completed Packets (0x13) plen 5
    handle 1 packets 1
2010-06-07 21:18:03.653808 > HCI Event: Auth Complete (0x06) plen 3
    status 0x00 handle 1
2010-06-07 21:18:03.653869 < ACL data: handle 1 flags 0x02 dlen 12
    L2CAP(s): Connect req: psm 1 scid 0x0040
...

Patch uses L2CAP_CONF_CONNECT_PEND flag to mark that L2CAP Connection
Request has been sent already.

Modified version of patch from Ville Tervo.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
11 years agoNET: SB1250: Initialize .owner
Ralf Baechle [Tue, 6 Jul 2010 05:18:11 +0000 (05:18 +0000)]
NET: SB1250: Initialize .owner

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
 drivers/net/sb1250-mac.c |    1 +
 1 files changed, 1 insertions(+), 0 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agovxge: show startup message with KERN_INFO
Wu Fengguang [Tue, 6 Jul 2010 03:02:03 +0000 (03:02 +0000)]
vxge: show startup message with KERN_INFO

The original KERN_CRIT will mess up terminals.

CC: Sreenivasa Honnur <Sreenivasa.Honnur@neterion.com>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoll_temac: Fix missing iounmaps
Denis Kirjanov [Mon, 5 Jul 2010 21:44:20 +0000 (21:44 +0000)]
ll_temac: Fix missing iounmaps

Fix missing iounmaps.

Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agobridge: Clear IPCB before possible entry into IP stack
Herbert Xu [Mon, 5 Jul 2010 21:29:28 +0000 (21:29 +0000)]
bridge: Clear IPCB before possible entry into IP stack

The bridge protocol lives dangerously by having incestuous relations
with the IP stack.  In this instance an abomination has been created
where a bogus IPCB area from a bridged packet leads to a crash in
the IP stack because it's interpreted as IP options.

This patch papers over the problem by clearing the IPCB area in that
particular spot.  To fix this properly we'd also need to parse any
IP options if present but I'm way too lazy for that.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Cheers,
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoath9k_htc: fix memory leak in ath9k_hif_usb_alloc_urbs
Rajkumar Manoharan [Wed, 7 Jul 2010 09:49:18 +0000 (15:19 +0530)]
ath9k_htc: fix memory leak in ath9k_hif_usb_alloc_urbs

Failure cases within ath9k_hif_usb_alloc_urbs are failed
to release allocated memory.

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agobridge br_multicast: BUG: unable to handle kernel NULL pointer dereference
Herbert Xu [Mon, 5 Jul 2010 14:50:08 +0000 (14:50 +0000)]
bridge br_multicast: BUG: unable to handle kernel NULL pointer dereference

On Tue, Jul 06, 2010 at 08:48:35AM +0800, Herbert Xu wrote:
>
> bridge: Restore NULL check in br_mdb_ip_get

Resend with proper attribution.

bridge: Restore NULL check in br_mdb_ip_get

Somewhere along the line the NULL check in br_mdb_ip_get went
AWOL, causing crashes when we receive an IGMP packet with no
multicast table allocated.

This patch restores it and ensures all br_mdb_*_get functions
use it.

Reported-by: Frank Arnold <frank.arnold@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Thanks,
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agonet: Fix definition of netif_vdbg() when VERBOSE_DEBUG is defined
Ben Hutchings [Fri, 2 Jul 2010 07:08:44 +0000 (07:08 +0000)]
net: Fix definition of netif_vdbg() when VERBOSE_DEBUG is defined

netif_vdbg() was originally defined as entirely equivalent to
netdev_vdbg(), but I assume that it was intended to take the same
parameters as netif_dbg() etc.  (Currently it is only used by the
sfc driver, in which I worked on that assumption.)

In commit a4ed89c I changed the definition used when VERBOSE_DEBUG is
not defined, but I failed to notice that the definition used when
VERBOSE_DEBUG is defined was also not as I expected.  Change that to
match netif_dbg() as well.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agonet/ne: fix memory leak in ne_drv_probe()
Kulikov Vasiliy [Sat, 3 Jul 2010 05:20:42 +0000 (05:20 +0000)]
net/ne: fix memory leak in ne_drv_probe()

net_device allocated with alloc_eip_netdev() must be freed.

Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoxfrm: fix xfrm by MARK logic
Peter Kosyh [Fri, 2 Jul 2010 07:47:55 +0000 (07:47 +0000)]
xfrm: fix xfrm by MARK logic

While using xfrm by MARK feature in
2.6.34 - 2.6.35 kernels, the mark
is always cleared in flowi structure via memset in
_decode_session4 (net/ipv4/xfrm4_policy.c), so
the policy lookup fails.
IPv6 code is affected by this bug too.

Signed-off-by: Peter Kosyh <p.kosyh@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoMerge branch 'vhost-net' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
David S. Miller [Sat, 3 Jul 2010 05:29:22 +0000 (22:29 -0700)]
Merge branch 'vhost-net' of git://git./linux/kernel/git/mst/vhost

11 years agovirtio_net: fix oom handling on tx
Rusty Russell [Fri, 2 Jul 2010 16:34:01 +0000 (16:34 +0000)]
virtio_net: fix oom handling on tx

virtio net will never try to overflow the TX ring, so the only reason
add_buf may fail is out of memory. Thus, we can not stop the
device until some request completes - there's no guarantee anything
at all is outstanding.

Make the error message clearer as well: error here does not
indicate queue full.

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (...and avoid TX_BUSY)
Cc: stable@kernel.org # .34.x (s/virtqueue_/vi->svq->vq_ops->/)
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agovirtio_net: do not reschedule rx refill forever
Michael S. Tsirkin [Fri, 2 Jul 2010 16:32:55 +0000 (16:32 +0000)]
virtio_net: do not reschedule rx refill forever

We currently fill all of RX ring, then add_buf
returns ENOSPC, which gets mis-detected as an out of
memory condition and causes us to reschedule the work,
and so on forever. Fix this by oom = err == -ENOMEM;

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org # .34.x
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agos2io: resolve statistics issues
Jon Mason [Fri, 2 Jul 2010 09:13:49 +0000 (09:13 +0000)]
s2io: resolve statistics issues

This patch resolves a number of issues in the statistics gathering of
the s2io driver.

On Xframe adapters, the received multicast statistics counter includes
pause frames which are not indicated to the driver.  This can cause
issues where the multicast packet count is higher than what has actually
been received, possibly higher than the number of packets received.

The driver software counters are replaced with the adapter hardware
statistics for rx_packets, rx_bytes, and tx_bytes.  It also uses the
overflow registers to determine if the statistics wrapped the 32bit
register (removing the window of having a statistic value less than the
previous call).  rx_length_errors statistic now includes undersized
packets in addition to oversized packets in its counting.  Finally,
rx_crc_errors are now being counted.

Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/kaber/nf-2.6
David S. Miller [Sat, 3 Jul 2010 05:04:49 +0000 (22:04 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/kaber/nf-2.6

11 years agolinux/net.h: fix kernel-doc warnings
Randy Dunlap [Thu, 1 Jul 2010 13:18:58 +0000 (13:18 +0000)]
linux/net.h: fix kernel-doc warnings

Fix kernel-doc warnings in linux/net.h:

Warning(include/linux/net.h:151): No description found for parameter 'wq'
Warning(include/linux/net.h:151): Excess struct/union/enum/typedef member 'fasync_list' description in 'socket'
Warning(include/linux/net.h:151): Excess struct/union/enum/typedef member 'wait' description in 'socket'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agonet: decreasing real_num_tx_queues needs to flush qdisc
John Fastabend [Thu, 1 Jul 2010 13:21:57 +0000 (13:21 +0000)]
net: decreasing real_num_tx_queues needs to flush qdisc

Reducing real_num_queues needs to flush the qdisc otherwise
skbs with queue_mappings greater then real_num_tx_queues can
be sent to the underlying driver.

The flow for this is,

dev_queue_xmit()
dev_pick_tx()
skb_tx_hash()  => hash using real_num_tx_queues
skb_set_queue_mapping()
...
qdisc_enqueue_root() => enqueue skb on txq from hash
...
dev->real_num_tx_queues -= n
...
sch_direct_xmit()
dev_hard_start_xmit()
ndo_start_xmit(skb,dev) => skb queue set with old hash

skbs are enqueued on the qdisc with skb->queue_mapping set
0 < queue_mappings < real_num_tx_queues.  When the driver
decreases real_num_tx_queues skb's may be dequeued from the
qdisc with a queue_mapping greater then real_num_tx_queues.

This fixes a case in ixgbe where this was occurring with DCB
and FCoE. Because the driver is using queue_mapping to map
skbs to tx descriptor rings we can potentially map skbs to
rings that no longer exist.

Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agosched: qdisc_reset_all_tx is calling qdisc_reset without qdisc_lock
John Fastabend [Thu, 1 Jul 2010 13:21:35 +0000 (13:21 +0000)]
sched: qdisc_reset_all_tx is calling qdisc_reset without qdisc_lock

When calling qdisc_reset() the qdisc lock needs to be held.  In
this case there is at least one driver i4l which is using this
without holding the lock.  Add the locking here.

Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoqlge: fix a eeh handler to not add a pending timer
Breno Leitao [Thu, 1 Jul 2010 03:00:18 +0000 (03:00 +0000)]
qlge: fix a eeh handler to not add a pending timer

On some ocasions the function qlge_io_resume() tries to add a
pending timer, which causes the system to hit the BUG() on
add_timer() function.

This patch removes the timer during the EEH recovery.

Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoqlge: Replacing add_timer() to mod_timer()
Breno Leitao [Thu, 1 Jul 2010 03:00:17 +0000 (03:00 +0000)]
qlge: Replacing add_timer() to mod_timer()

Currently qlge driver calls add_timer() instead of mod_timer().
This patch changes add_timer() to mod_timer(), which seems a better
solution.

Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agousbnet: Set parent device early for netdev_printk()
Ben Hutchings [Sat, 3 Jul 2010 04:49:02 +0000 (21:49 -0700)]
usbnet: Set parent device early for netdev_printk()

netdev_printk() follows the net_device's parent device pointer, so
we must set that earlier than we previously did.

Reported-by: Luís Picciochi Oliveira <pitxyoki@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agonet: Revert "rndis_host: Poll status channel before control channel"
Ben Hutchings [Sat, 3 Jul 2010 04:47:54 +0000 (21:47 -0700)]
net: Revert "rndis_host: Poll status channel before control channel"

This reverts commit c17b274dc2aa538b68c1f02b01a3c4e124b435ba.

That change was reported to break rndis_wlan support for the WUSB54GS.

Reported-by: Luís Picciochi Oliveira <pitxyoki@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoiwlwifi: remove key information during device restart
Reinette Chatre [Mon, 21 Jun 2010 21:23:47 +0000 (14:23 -0700)]
iwlwifi: remove key information during device restart

When there is a firmware error or the firmware is reloaded for some other
reason we currently clear all station information, including keys
associated with them. A problem is that we do not clear some other
information regarding keys that are not stored in the station structs.

The consequence of this is that when the device is reconfigured after the
firmware reload we can, among other things, run out of key indices.

This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=16232
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2221

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
11 years agonetfilter: ip6t_REJECT: fix a dst leak in ipv6 REJECT
Eric Dumazet [Fri, 2 Jul 2010 08:05:01 +0000 (10:05 +0200)]
netfilter: ip6t_REJECT: fix a dst leak in ipv6 REJECT

We should release dst if dst->error is set.

Bug introduced in 2.6.14 by commit e104411b82f5c
([XFRM]: Always release dst_entry on error in xfrm_lookup)

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Patrick McHardy <kaber@trash.net>
11 years agodrivers: bluetooth: bluecard_cs.c: Fixed include error, changed to linux/io.h
Cody Rester [Fri, 2 Jul 2010 04:27:44 +0000 (21:27 -0700)]
drivers: bluetooth: bluecard_cs.c: Fixed include error, changed to linux/io.h

Fixed include error, changed to linux/io.h

Signed-off-by: Cody Rester <codyrester@gmail.com>
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agovhost: add unlikely annotations to error path
Michael S. Tsirkin [Thu, 1 Jul 2010 15:40:12 +0000 (18:40 +0300)]
vhost: add unlikely annotations to error path

patch 'break out of polling loop on error' caused
a minor performance regression on my machine: recover
that performance by adding a bunch of unlikely annotations
in the error handling.

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
11 years agobonding: check if clients MAC addr has changed
Flavio Leitner [Tue, 29 Jun 2010 08:24:39 +0000 (08:24 +0000)]
bonding: check if clients MAC addr has changed

When two systems using bonding devices in adaptive load
balancing (ALB) communicates with each other, an endless
ping-pong of ARP replies starts between these two systems.

What happens? In the ALB mode, bonding driver keeps track
of each client connected in a hash table, so it can do the
receive load balancing (RLB). This hash table is updated
when an ARP reply is received, then it scans for the client
entry, updates its MAC address and flag it to be announced
later. Therefore, two seconds later, the alb monitor runs
and send for each updated client entry two ARP replies
updating this specific client. The same process happens on
the receiving system, causing the endless ping-pong of arp
replies.

See more information including the relevant functions below:

   System 1                          System 2
    bond0                             bond0

   ping <system2>
    ARP request  --------->
                           <--------- ARP reply

+->rlb_arp_recv  <---------------------+   <--- loop begins
|  rlb_update_entry_from_arp           |
|  client_info->ntt = 1;               |
|  bond_info->rx_ntt = 1;              |
|                                      |
|         <communication succeed>      |
|                                      |
|  bond_alb_monitor                    |
|  rlb_update_rx_clients               |
|  rlb_update_client                   |
|  arp_create(ARPOP_REPLY)             |
|   send ARP reply -------------->     V
|   send ARP reply -------------->
|                               rlb_arp_recv
|                               rlb_update_entry_from_arp
|                               client_info->ntt = 1;
|                               bond_info->rx_ntt = 1;
|                           < snipped, same as in system 1>
+-------           <-------------- send ARP reply
                   <-------------- send ARP reply

Besides the unneeded networking traffic, this loop breaks
a cluster because a backup system can't take over the IP
address. There is always one system sending an ARP reply
poisoning the network.

This patch fixes the problem adding a check for the MAC
address before updating it. Thus, if the MAC address didn't
change, there is no need to update neither to announce it later.

Signed-off-by: Flavio Leitner <fleitner@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoBluetooth: Fix abuse of the preincrement operator
David Howells [Wed, 30 Jun 2010 20:10:09 +0000 (13:10 -0700)]
Bluetooth: Fix abuse of the preincrement operator

Fix abuse of the preincrement operator as detected when building with gcc
4.6.0:

 CC [M]  drivers/bluetooth/hci_bcsp.o
drivers/bluetooth/hci_bcsp.c: In function 'bcsp_prepare_pkt':
drivers/bluetooth/hci_bcsp.c:247:20: warning: operation on 'bcsp->msgq_txseq' may be undefined

Reported-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agomv643xx_eth: use sw csum for big packets
Saeed Bishara [Sun, 27 Jun 2010 00:26:43 +0000 (00:26 +0000)]
mv643xx_eth: use sw csum for big packets

Some controllers (KW, Dove) limits the TX IP/layer4 checksum offloading to a max size.

Signed-off-by: Saeed Bishara <saeed@marvell.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wirel...
David S. Miller [Wed, 30 Jun 2010 19:04:58 +0000 (12:04 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6

11 years agoxfrm: fix XFRMA_MARK extraction in xfrm_mark_get
Andreas Steffen [Wed, 30 Jun 2010 17:41:15 +0000 (10:41 -0700)]
xfrm: fix XFRMA_MARK extraction in xfrm_mark_get

Determine the size of the xfrm_mark struct, not of its pointer.

Signed-off-by: Andreas Steffen <andreas.steffen@strongswan.org>
Acked-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoixgbe: skip non IPv4 packets in ATR filter
Guillaume Gaudonville [Tue, 29 Jun 2010 18:29:00 +0000 (18:29 +0000)]
ixgbe: skip non IPv4 packets in ATR filter

In driver ixgbe, ixgbe_atr may cause crashes for non-ipv4 packets. Just
add a test to check skb->protocol.  It may crash on short packets due
to ip_hdr() access.

Signed-off-by: Guillaume Gaudonville <guillaume.gaudonville@6wind.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoixgbe: disable tx engine before disabling tx laser
John Fastabend [Tue, 29 Jun 2010 18:28:36 +0000 (18:28 +0000)]
ixgbe: disable tx engine before disabling tx laser

Disabling the tx laser while receiving DMA requests
can hang the device.  After this occurs the device
is in a bad state. The GPIO bit never clears when
PCI master access is disabled and a reboot is required
to get the device in a good state again.

Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoixgbe: fix panic when shutting down system with WoL enabled
Andy Gospodarek [Tue, 29 Jun 2010 18:28:12 +0000 (18:28 +0000)]
ixgbe: fix panic when shutting down system with WoL enabled

This patch added to 2.6.34:

commit 5f6c01819979afbfec7e0b15fe52371b8eed87e8
Author: Jesse Brandeburg <jesse.brandeburg@intel.com>
Date:   Wed Apr 14 16:04:23 2010 -0700

    ixgbe: fix bug with vlan strip in promsic mode

among other things added a function called ixgbe_vlan_filter_enable.
This new function wants to access and set some rx_ring parameters, but
adapter->rx_ring has already been freed.  This simply moves the free
until after the access and makes __ixgbe_shutdown look more like
ixgbe_remove.

Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoethtool: Fix potential user buffer overflow for ETHTOOL_{G, S}RXFH
Ben Hutchings [Mon, 28 Jun 2010 08:45:58 +0000 (08:45 +0000)]
ethtool: Fix potential user buffer overflow for ETHTOOL_{G, S}RXFH

struct ethtool_rxnfc was originally defined in 2.6.27 for the
ETHTOOL_{G,S}RXFH command with only the cmd, flow_type and data
fields.  It was then extended in 2.6.30 to support various additional
commands.  These commands should have been defined to use a new
structure, but it is too late to change that now.

Since user-space may still be using the old structure definition
for the ETHTOOL_{G,S}RXFH commands, and since they do not need the
additional fields, only copy the originally defined fields to and
from user-space.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoethtool: Fix potential kernel buffer overflow in ETHTOOL_GRXCLSRLALL
Ben Hutchings [Mon, 28 Jun 2010 08:44:07 +0000 (08:44 +0000)]
ethtool: Fix potential kernel buffer overflow in ETHTOOL_GRXCLSRLALL

On a 32-bit machine, info.rule_cnt >= 0x40000000 leads to integer
overflow and the buffer may be smaller than needed.  Since
ETHTOOL_GRXCLSRLALL is unprivileged, this can presumably be used for at
least denial of service.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agobonding: prevent netpoll over bonded interfaces
Andy Gospodarek [Fri, 25 Jun 2010 09:50:44 +0000 (09:50 +0000)]
bonding: prevent netpoll over bonded interfaces

Support for netpoll over bonded interfaces was added here:

commit f6dc31a85cd46a959bdd987adad14c3b645e03c1
Author: WANG Cong <amwang@redhat.com>
Date:   Thu May 6 00:48:51 2010 -0700

    bonding: make bonding support netpoll

but it is bad enough that we should probably just disable netpoll over
bonding until some of the locking logic in the bonding driver is changed
or converted completely to RCU.  Simple actions like changing the active
slave in active-backup mode will hang the box if a high enough printk
debugging level is enabled.

Keeping the old code around will be good for anyone that wants to work
on it (and for after the RCU conversion), so I propose this small patch
rather than ripping it all out.

Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agovhost: break out of polling loop on error
Michael S. Tsirkin [Thu, 24 Jun 2010 13:59:59 +0000 (16:59 +0300)]
vhost: break out of polling loop on error

When ring parsing fails, we currently handle this
as ring empty condition. This means that we enable
kicks and recheck ring empty: if this not empty,
we re-start polling which of course will fail again.

Instead, let's return a negative error code and stop polling.

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
11 years agophylib: Add autoload support for the LXT973 phy.
David Woodhouse [Tue, 22 Jun 2010 02:38:13 +0000 (02:38 +0000)]
phylib: Add autoload support for the LXT973 phy.

Commit e13647c1 (phylib: Add support for the LXT973 phy.) added a new ID
but neglected to also add it to the MODULE_DEVICE_TABLE.

Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoISDN: hysdn, fix potential NULL dereference
Jiri Slaby [Tue, 22 Jun 2010 01:41:36 +0000 (01:41 +0000)]
ISDN: hysdn, fix potential NULL dereference

Stanse found that lp is dereferenced earlier than checked for being
NULL in hysdn_rx_netpkt. Move the initialization below the test.

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agovxge: fix memory leak in vxge_alloc_msix() error path
Michal Schmidt [Thu, 24 Jun 2010 04:13:44 +0000 (04:13 +0000)]
vxge: fix memory leak in vxge_alloc_msix() error path

When pci_enable_msix() returned ret<0, entries and vxge_entries were leaked.
While at it, use the centralized exit idiom in the function.

Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Ram Vepa <ram.vepa@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoisdn/gigaset: correct CAPI connection state storage
Tilman Schmidt [Mon, 21 Jun 2010 13:55:20 +0000 (13:55 +0000)]
isdn/gigaset: correct CAPI connection state storage

CAPI applications can handle several connections in parallel,
so one connection state per application isn't sufficient.
Store the connection state in the channel structure instead.

Impact: bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoisdn/gigaset: encode HLC and BC together
Tilman Schmidt [Mon, 21 Jun 2010 13:55:05 +0000 (13:55 +0000)]
isdn/gigaset: encode HLC and BC together

Adapt to buggy device firmware which accepts setting HLC only in the
same command line as BC, by encoding HLC and BC in a single command
if both are specified, and rejecting HLC without BC.

Impact: bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoisdn/gigaset: correct CAPI DATA_B3 Delivery Confirmation
Tilman Schmidt [Mon, 21 Jun 2010 13:54:50 +0000 (13:54 +0000)]
isdn/gigaset: correct CAPI DATA_B3 Delivery Confirmation

The Gigaset CAPI driver handled all DATA_B3_REQ messages as if the
Delivery Confirmation flag bit was set, delaying the emission of the
DATA_B3_CONF reply until the data was actually transmitted. Some
CAPI applications (notably Asterisk) aren't happy with that
behaviour. Change it to actually evaluate the Delivery Confirmation
flag as described the CAPI specification.

Impact: bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoisdn/gigaset: correct CAPI voice connection encoding
Tilman Schmidt [Mon, 21 Jun 2010 13:54:35 +0000 (13:54 +0000)]
isdn/gigaset: correct CAPI voice connection encoding

Make the Gigaset CAPI driver select L2_VOICE (AT^SBPR=2) as the
layer 2 encoding for transparent connections, like the ISDN4Linux
variant.  L2_BITSYNC (AT^SBPR=0) mutes internal connections and
distorts external ones.

Impact: bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoisdn/gigaset: honor CAPI application's buffer size request
Tilman Schmidt [Mon, 21 Jun 2010 13:54:19 +0000 (13:54 +0000)]
isdn/gigaset: honor CAPI application's buffer size request

Fix the Gigaset CAPI driver to limit the length of a connection's
payload data receive buffers to the corresponding CAPI application's
data buffer size, as some real-life CAPI applications tend to be
rather unhappy if they receive bigger data blocks than requested.

Impact: bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agocpmac: do not leak struct net_device on phy_connect errors
Florian Fainelli [Sun, 20 Jun 2010 22:07:48 +0000 (22:07 +0000)]
cpmac: do not leak struct net_device on phy_connect errors

If the call to phy_connect fails, we will return directly instead of freeing
the previously allocated struct net_device.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
CC: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agosmc91c92_cs: fix the problem that lan & modem does not work simultaneously
Ken Kawasaki [Sat, 19 Jun 2010 15:24:27 +0000 (15:24 +0000)]
smc91c92_cs: fix the problem that lan & modem does not work simultaneously

smc91c92_cs:
  Fix the problem that lan & modem does not work simultaneously
  in the Megahertz multi-function card.
  We need to write MEGAHERTZ_ISR to retrigger interrupt.

Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoipv6: fix NULL reference in proxy neighbor discovery
stephen hemminger [Mon, 21 Jun 2010 11:00:13 +0000 (11:00 +0000)]
ipv6: fix NULL reference in proxy neighbor discovery

The addition of TLLAO option created a kernel OOPS regression
for the case where neighbor advertisement is being sent via
proxy path.  When using proxy, ipv6_get_ifaddr() returns NULL
causing the NULL dereference.

Change causing the bug was:
commit f7734fdf61ec6bb848e0bafc1fb8bad2c124bb50
Author: Octavian Purdila <opurdila@ixiacom.com>
Date:   Fri Oct 2 11:39:15 2009 +0000

    make TLLAO option for NA packets configurable

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoiwlwifi: set TX_CMD_FLAG_PROT_REQUIRE_MSK in tx_flag
Wey-Yi Guy [Fri, 18 Jun 2010 18:33:17 +0000 (11:33 -0700)]
iwlwifi: set TX_CMD_FLAG_PROT_REQUIRE_MSK in tx_flag

When building tx command, always set TX_CMD_FLAG_PROT_REQUIRE_MSK
for 5000 series and up.

Without setting this bit the firmware will not examine the RTS/CTS setting
and thus not send traffic with the appropriate protection. RTS/CTS is is
required for HT traffic in a noisy environment where, without this setting,
connections will stall on some hardware as documented in the patch that
initially attempted to address this:

    commit 1152dcc28c66a74b5b3f1a3ede0aa6729bfd48e4
    Author: Wey-Yi Guy <wey-yi.w.guy@intel.com>
    Date:   Fri Jan 15 13:42:58 2010 -0800

    iwlwifi: Fix throughput stall issue in HT mode for 5000

    Similar to 6000 and 1000 series, RTS/CTS is the recommended
    protection mechanism for 5000 series in HT mode based on the HW design.
    Using RTS/CTS will better protect the inner exchange from interference,
    especially in highly-congested environment, it also prevent uCode encounter
    TX FIFO underrun and other HT mode related performance issues.

For 3945 and 4965, different flags are used for RTS/CTS or CTS-to-Self
protection.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
11 years agoiwlwifi: fix multicast
Johannes Berg [Fri, 18 Jun 2010 10:41:25 +0000 (03:41 -0700)]
iwlwifi: fix multicast

commit 3474ad635db371b0d8d0ee40086f15d223d5b6a4
Author: Johannes Berg <johannes.berg@intel.com>
Date:   Thu Apr 29 04:43:05 2010 -0700

    iwlwifi: apply filter flags directly

broke multicast. The reason, it turns out, is that
the code previously checked if ALLMULTI _changed_,
which the new code no longer did, and normally it
_never_ changes. Had somebody changed it manually,
the code prior to my patch there would have been
broken already.

The reason is that we always, unconditionally, ask
the device to pass up all multicast frames, but the
new code made it depend on ALLMULTI which broke it
since now we'd pass up multicast frames depending
on the default filter in the device, which isn't
necessarily what we want (since we don't program it
right now).

Fix this by simply not checking allmulti as we have
allmulti behaviour enabled already anyway.

Reported-by: Maxim Levitsky <maximlevitsky@gmail.com>
Tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
11 years agoBluetooth: Bring back var 'i' increment
Gustavo F. Padovan [Fri, 18 Jun 2010 14:24:00 +0000 (14:24 +0000)]
Bluetooth: Bring back var 'i' increment

commit ff6e2163f28a1094fb5ca5950fe2b43c3cf6bc7a accidentally added a
regression on the bnep code. Fixing it.

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoxfrm: check bundle policy existance before dereferencing it
Timo Teräs [Thu, 24 Jun 2010 21:35:00 +0000 (14:35 -0700)]
xfrm: check bundle policy existance before dereferencing it

Fix the bundle validation code to not assume having a valid policy.
When we have multiple transformations for a xfrm policy, the bundle
instance will be a chain of bundles with only the first one having
the policy reference. When policy_genid is bumped it will expire the
first bundle in the chain which is equivalent of expiring the whole
chain.

Reported-bisected-and-tested-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agosky2: enable rx/tx in sky2_phy_reinit()
Brandon Philips [Wed, 16 Jun 2010 16:21:58 +0000 (16:21 +0000)]
sky2: enable rx/tx in sky2_phy_reinit()

sky2_phy_reinit is called by the ethtool helpers sky2_set_settings,
sky2_nway_reset and sky2_set_pauseparam when netif_running.

However, at the end of sky2_phy_init GM_GP_CTRL has GM_GPCR_RX_ENA and
GM_GPCR_TX_ENA cleared. So, doing these commands causes the device to
stop working:

$ ethtool -r eth0
$ ethtool -A eth0 autoneg off

Fix this issue by enabling Rx/Tx after running sky2_phy_init in
sky2_phy_reinit.

Signed-off-by: Brandon Philips <bphilips@suse.de>
Tested-by: Brandon Philips <bphilips@suse.de>
Cc: stable@kernel.org
Tested-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoath9k: Fix bug in starting ani
Vasanthakumar Thiagarajan [Wed, 23 Jun 2010 13:49:21 +0000 (06:49 -0700)]
ath9k: Fix bug in starting ani

There are few places where ANI is started without checking
if it is right to start. This might lead to a case where ani
timer would be left undeleted and cause improper memory acccess
during module unload. This bug is clearly exposed with
paprd support where the driver detects tx hang and does a
chip reset. During this reset ani is (re)started without checking
if it needs to be started. This would leave a timer scheduled
even after all the resources are freed and cause a panic.

This patch introduces a bit in sc_flags to indicate if ani
needs to be started in sw_scan_start() and ath_reset().
This would fix the following panic. This issue is easily seen
with ar9003 + paprd.

 BUG: unable to handle kernel paging request at 0000000000003f38
[<ffffffff81075391>] ? __queue_work+0x41/0x50
[<ffffffff8106afaa>] run_timer_softirq+0x17a/0x370
[<ffffffff81088be8>] ? tick_dev_program_event+0x48/0x110
[<ffffffff81061f69>] __do_softirq+0xb9/0x1f0
[<ffffffff810ba060>] ? handle_IRQ_event+0x50/0x160
[<ffffffff8100af5c>] call_softirq+0x1c/0x30
[<ffffffff8100c9f5>] do_softirq+0x65/0xa0
[<ffffffff81061e25>] irq_exit+0x85/0x90
[<ffffffff8155e095>] do_IRQ+0x75/0xf0
[<ffffffff815570d3>] ret_from_intr+0x0/0x11
<EOI>
[<ffffffff812fd67b>] ? acpi_idle_enter_simple+0xe4/0x119
[<ffffffff812fd674>] ? acpi_idle_enter_simple+0xdd/0x119
[<ffffffff81441c87>] cpuidle_idle_call+0xa7/0x140
[<ffffffff81008da3>] cpu_idle+0xb3/0x110
[<ffffffff81550722>] start_secondary+0x1ee/0x1f5

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agocnic: Disable statistics initialization for eth clients that do not support statistics
Dmitry Kravkov [Wed, 23 Jun 2010 18:57:09 +0000 (11:57 -0700)]
cnic: Disable statistics initialization for eth clients that do not support statistics

Disable statistics initialization for eth clients that do not support
 statistics. This prevents memory corruption on bnx2x hw.

Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
11 years agonet: add dependency on fw class module to qlcnic and netxen_nic
Anirban Chakraborty [Wed, 23 Jun 2010 18:49:42 +0000 (11:49 -0700)]
net: add dependency on fw class module to qlcnic and netxen_nic

netxen_nic and qlcnic driver depends on firmware_class module.

Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agosnmp: fix SNMP_ADD_STATS()
Eric Dumazet [Wed, 23 Jun 2010 00:32:03 +0000 (00:32 +0000)]
snmp: fix SNMP_ADD_STATS()

commit aa2ea0586d9d (tcp: fix outsegs stat for TSO segments) incorrectly
assumed SNMP_ADD_STATS() was used from BH context.

Fix this using mib[!in_softirq()] instead of mib[0]

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wirel...
David S. Miller [Tue, 22 Jun 2010 17:54:12 +0000 (10:54 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6

11 years agohso: remove setting of low_latency flag
Filip Aben [Tue, 22 Jun 2010 17:10:35 +0000 (10:10 -0700)]
hso: remove setting of low_latency flag

This patch removes the setting of the low_latency flag.
tty_flip_buffer_push() is occasionally being called in irq context, which
causes a hang if the low_latency flag is set.
Removing the low_latency flag only seems to impact the flush to ldisc,
which will now be put on a workqueue.

Signed-off-by: Filip Aben <f.aben@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoudp: Fix bogus UFO packet generation
Herbert Xu [Tue, 15 Jun 2010 01:52:25 +0000 (01:52 +0000)]
udp: Fix bogus UFO packet generation

It has been reported that the new UFO software fallback path
fails under certain conditions with NFS.  I tracked the problem
down to the generation of UFO packets that are smaller than the
MTU.  The software fallback path simply discards these packets.

This patch fixes the problem by not generating such packets on
the UFO path.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agolasi82596: fix netdev_mc_count conversion
Helge Deller [Mon, 21 Jun 2010 20:50:18 +0000 (13:50 -0700)]
lasi82596: fix netdev_mc_count conversion

Fix commit 4cd24eaf0 (net: use netdev_mc_count and netdev_mc_empty when
appropriate)

Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoNET: MIPSsim: Fix modpost warning.
Ralf Baechle [Mon, 21 Jun 2010 03:44:50 +0000 (03:44 +0000)]
NET: MIPSsim: Fix modpost warning.

$ make CONFIG_DEBUG_SECTION_MISMATCH=y
[...]
WARNING: drivers/net/built-in.o(.data+0x0): Section mismatch in reference from the variable mipsnet_driver to the function .init.text:mipsnet_probe()
The variable mipsnet_driver references
the function __init mipsnet_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
[...]

Fixed by making mipsnet_probe __devinit.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
 drivers/net/mipsnet.c |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoath5k: initialize ah->ah_current_channel
Bob Copeland [Fri, 18 Jun 2010 17:15:23 +0000 (13:15 -0400)]
ath5k: initialize ah->ah_current_channel

ath5k assumes ah_current_channel is always a valid pointer in
several places, but a newly created interface may not have a
channel.  To avoid null pointer dereferences, set it up to point
to the first available channel until later reconfigured.

This fixes the following oops:
$ rmmod ath5k
$ insmod ath5k
$ iw phy0 set distance 11000

BUG: unable to handle kernel NULL pointer dereference at 00000006
IP: [<d0a1ff24>] ath5k_hw_set_coverage_class+0x74/0x1b0 [ath5k]
*pde = 00000000
Oops: 0000 [#1]
last sysfs file: /sys/devices/pci0000:00/0000:00:0e.0/ieee80211/phy0/index
Modules linked in: usbhid option usb_storage usbserial usblp evdev lm90
scx200_acb i2c_algo_bit i2c_dev i2c_core via_rhine ohci_hcd ne2k_pci
8390 leds_alix2 xt_IMQ imq nf_nat_tftp nf_conntrack_tftp nf_nat_irc nf_cc

Pid: 1597, comm: iw Not tainted (2.6.32.14 #8)
EIP: 0060:[<d0a1ff24>] EFLAGS: 00010296 CPU: 0
EIP is at ath5k_hw_set_coverage_class+0x74/0x1b0 [ath5k]
EAX: 000000c2 EBX: 00000000 ECX: ffffffff EDX: c12d2080
ESI: 00000019 EDI: cf8c0000 EBP: d0a30edc ESP: cfa09bf4
  DS: 007b ES: 007b FS: 0000 GS: 0000 SS: 0068
Process iw (pid: 1597, ti=cfa09000 task=cf88a000 task.ti=cfa09000)
Stack:
  d0a34f35 d0a353f8 d0a30edc 000000fe cf8c0000 00000000 1900063d cfa8c9e0
<0> cfa8c9e8 cfa8c0c0 cfa8c000 d0a27f0c 199d84b4 cfa8c200 00000010 d09bfdc7
<0> 00000000 00000000 ffffffff d08e0d28 cf9263c0 00000001 cfa09cc4 00000000
Call Trace:
  [<d0a27f0c>] ? ath5k_hw_attach+0xc8c/0x3c10 [ath5k]
  [<d09bfdc7>] ? __ieee80211_request_smps+0x1347/0x1580 [mac80211]
  [<d08e0d28>] ? nl80211_send_scan_start+0x7b8/0x4520 [cfg80211]
  [<c10f5db9>] ? nla_parse+0x59/0xc0
  [<c11ca8d9>] ? genl_rcv_msg+0x169/0x1a0
  [<c11ca770>] ? genl_rcv_msg+0x0/0x1a0
  [<c11c7e68>] ? netlink_rcv_skb+0x38/0x90
  [<c11c9649>] ? genl_rcv+0x19/0x30
  [<c11c7c03>] ? netlink_unicast+0x1b3/0x220
  [<c11c893e>] ? netlink_sendmsg+0x26e/0x290
  [<c11a409e>] ? sock_sendmsg+0xbe/0xf0
  [<c1032780>] ? autoremove_wake_function+0x0/0x50
  [<c104d846>] ? __alloc_pages_nodemask+0x106/0x530
  [<c1074933>] ? do_lookup+0x53/0x1b0
  [<c10766f9>] ? __link_path_walk+0x9b9/0x9e0
  [<c11acab0>] ? verify_iovec+0x50/0x90
  [<c11a42b1>] ? sys_sendmsg+0x1e1/0x270
  [<c1048e50>] ? find_get_page+0x10/0x50
  [<c104a96f>] ? filemap_fault+0x5f/0x370
  [<c1059159>] ? __do_fault+0x319/0x370
  [<c11a55b4>] ? sys_socketcall+0x244/0x290
  [<c101962c>] ? do_page_fault+0x1ec/0x270
  [<c1019440>] ? do_page_fault+0x0/0x270
  [<c1002ae5>] ? syscall_call+0x7/0xb
Code: 00 b8 fe 00 00 00 b9 f8 53 a3 d0 89 5c 24 14 89 7c 24 10 89 44 24
0c 89 6c 24 08 89 4c 24 04 c7 04 24 35 4f a3 d0 e8 7c 30 60 f0 <0f> b7
43 06 ba 06 00 00 00 a8 10 75 0e 83 e0 20 83 f8 01 19 d2
EIP: [<d0a1ff24>] ath5k_hw_set_coverage_class+0x74/0x1b0 [ath5k] SS:ESP
0068:cfa09bf4
CR2: 0000000000000006
---[ end trace 54f73d6b10ceb87b ]---

Cc: stable@kernel.org
Reported-by: Steve Brown <sbrown@cortland.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agobridge: fdb cleanup runs too often
stephen hemminger [Tue, 15 Jun 2010 06:14:12 +0000 (06:14 +0000)]
bridge: fdb cleanup runs too often

It is common in end-node, non STP bridges to set forwarding
delay to zero; which causes the forwarding database cleanup
to run every clock tick. Change to run only as soon as needed
or at next ageing timer interval which ever is sooner.

Use round_jiffies_up macro rather than attempting round up
by changing value.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agobnx2: fix dma_get_ops compilation breakage
FUJITA Tomonori [Thu, 17 Jun 2010 15:56:05 +0000 (08:56 -0700)]
bnx2: fix dma_get_ops compilation breakage

This removes dma_get_ops() prefetch optimization in bnx2.

bnx2 uses dma_get_ops() to see if dma_sync_single_for_cpu() is
noop. bnx2 does prefetch if it's noop.

But dma_get_ops() isn't available on all the architectures (only the
architectures that uses dma_map_ops struct have it). Using
dma_get_ops() in drivers leads to compilation breakage on many
architectures.

This patch removes dma_get_ops() and changes bnx2 to do prefetch on
all the architectures. This adds useless prefetch on non-coherent
architectures but this is harmless. It is also unlikely to cause the
performance drop.

[ Remove now unused local variable 'pdev' -DaveM ]

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoucc_geth: fix for RX skb buffers recycling
Sergey Matyukevich [Mon, 14 Jun 2010 06:35:20 +0000 (06:35 +0000)]
ucc_geth: fix for RX skb buffers recycling

This patch implements a proper modification of RX skb buffers before
recycling. Adjusting only skb->data is not enough because after that
skb->tail and skb->len become incorrect.

Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agopcnet_cs: add new id (TOSHIBA Modem/LAN Card)
Ken Kawasaki [Sat, 12 Jun 2010 00:17:28 +0000 (00:17 +0000)]
pcnet_cs: add new id (TOSHIBA Modem/LAN Card)

pcnet_cs:
serial_cs:
    add new id (TOSHIBA Modem/LAN Card)

Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agogianfar: Fix oversized packets handling
Anton Vorontsov [Fri, 11 Jun 2010 10:51:03 +0000 (10:51 +0000)]
gianfar: Fix oversized packets handling

Issuing the following command on host:

$ ifconfig eth2 mtu 1600 ; ping 10.0.0.27 -s 1485 -c 1

Makes some boards (tested with MPC8315 rev 1.1 and MPC8313 rev 1.0)
oops like this:

  skb_over_panic: text:c0195914 len:1537 put:1537 head:c79e4800 data:c79e4880 tail:0xc79e4e81 end:0xc79e4e80 dev:eth1
  ------------[ cut here ]------------
  kernel BUG at net/core/skbuff.c:127!
  Oops: Exception in kernel mode, sig: 5 [#1]
  MPC831x RDB
  last sysfs file: /sys/kernel/uevent_seqnum
  Modules linked in:
  NIP: c01c1840 LR: c01c1840 CTR: c016d918
  [...]
  NIP [c01c1840] skb_over_panic+0x48/0x5c
  LR [c01c1840] skb_over_panic+0x48/0x5c
  Call Trace:
  [c0339d50] [c01c1840] skb_over_panic+0x48/0x5c (unreliable)
  [c0339d60] [c01c3020] skb_put+0x5c/0x60
  [c0339d70] [c0195914] gfar_clean_rx_ring+0x25c/0x3d0
  [c0339dc0] [c01976e8] gfar_poll+0x170/0x1bc

Dumped buffer descriptors showed that eTSEC's length/truncation
logic sometimes passes oversized packets, i.e. for the above ICMP
packet the following two buffer descriptors may become ready:

  status=1400 length=1536
  status=1800 length=1541

So, it seems that gianfar actually receives the whole big frame,
and it tries to place the packet into two BDs. This situation
confuses the driver, and so the skb_put() sanity check fails.

This patch fixes the issue by adding an appropriate check, i.e.
the driver should not try to process frames with buffer
descriptor's length over rx_buffer_size (i.e. maxfrm and mrblr).

Note that sometimes eTSEC works correctly, i.e. in the second
(last) buffer descriptor bits 'truncated' and 'crcerr' are set,
and so there's no oops. Though I couldn't find any logic when
it works correctly and when not.

Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoehea: Fix kernel deadlock in DLPAR-mem processing
Jan-Bernd Themann [Tue, 15 Jun 2010 05:35:42 +0000 (05:35 +0000)]
ehea: Fix kernel deadlock in DLPAR-mem processing

Port reset operations and memory add/remove operations need to
be serialized to avoid a kernel deadlock. The deadlock is caused
by calling the napi_disable() function twice.
Therefore we have to employ the dlpar_mem_lock in the ehea_reset_port
function as well

Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoehea: fix delayed packet processing
Jan-Bernd Themann [Tue, 15 Jun 2010 05:35:16 +0000 (05:35 +0000)]
ehea: fix delayed packet processing

In the eHEA poll function an rmb() is required. Without that some packets
on the receive queue are not seen and thus delayed until the next interrupt
is handled for the same receive queue.

Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoixgbe: add comment on SFP+ ID for Active DA
Don Skidmore [Tue, 15 Jun 2010 09:23:17 +0000 (09:23 +0000)]
ixgbe: add comment on SFP+ ID for Active DA

These comments were forgotten in the initial patch to add this
functionality.  This patch corrects that.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoClear IFF_XMIT_DST_RELEASE for teql interfaces
Tom Hughes [Tue, 15 Jun 2010 22:24:28 +0000 (22:24 +0000)]
Clear IFF_XMIT_DST_RELEASE for teql interfaces

https://bugzilla.kernel.org/show_bug.cgi?id=16183

The sch_teql module, which can be used to load balance over a set of
underlying interfaces, stopped working after 2.6.30 and has been
broken in all kernels since then for any underlying interface which
requires the addition of link level headers.

The problem is that the transmit routine relies on being able to
access the destination address in the skb in order to do address
resolution once it has decided which underlying interface it is going
to transmit through.

In 2.6.31 the IFF_XMIT_DST_RELEASE flag was introduced, and set by
default for all interfaces, which causes the destination address to be
released before the transmit routine for the interface is called.

The solution is to clear that flag for teql interfaces.

Signed-off-by: Tom Hughes <tom@compton.nu>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agogianfar: Fix setup of RX time stamping
Manfred Rudigier [Fri, 11 Jun 2010 01:49:05 +0000 (01:49 +0000)]
gianfar: Fix setup of RX time stamping

Previously the RCTRL_TS_ENABLE bit was set unconditionally. However, if
the RCTRL_TS_ENABLE is set without TMR_CTRL[TE], the driver does not work
properly on some boards (Anton had problems with the MPC8313ERDB and
MPC8568EMDS).

With this patch the bit will only be set if requested from user space
with the SIOCSHWTSTAMP ioctl command, meaning that time stamping is
disabled during normal operation. Users who are not interested in time
stamps will not experience problems with buggy CPU revisions or
performance drops any more.

The setting of TMR_CTRL[TE] is still up to the user. This is considered
safe because users wanting HW timestamps must initialize the eTSEC clock
first anyway, e.g. with the recently submitted PTP clock driver.

Signed-off-by: Manfred Rudigier <manfred.rudigier@omicron.at>
Reviewed-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wirel...
David S. Miller [Wed, 16 Jun 2010 20:41:55 +0000 (13:41 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6

11 years agomac80211: fix warn, enum may be used uninitialized
Christoph Fritz [Wed, 16 Jun 2010 14:37:34 +0000 (16:37 +0200)]
mac80211: fix warn, enum may be used uninitialized

regression introduced by b8d92c9c141ee3dc9b3537b1f0ffb4a54ea8d9b2

In function ‘ieee80211_work_rx_queued_mgmt’:
warning: ‘rma’ may be used uninitialized in this function

this re-adds default value WORK_ACT_NONE back to rma

Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
11 years agobridge: Fix OOM crash in deliver_clone
Herbert Xu [Wed, 16 Jun 2010 04:43:07 +0000 (21:43 -0700)]
bridge: Fix OOM crash in deliver_clone

The bridge multicast patches introduced an OOM crash in the forward
path, when deliver_clone fails to clone the skb.

Reported-by: Mark Wagner <mwagner@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
11 years agonetxen: fix caching window register
Amit Kumar Salecha [Sun, 13 Jun 2010 23:39:05 +0000 (23:39 +0000)]
netxen: fix caching window register

CRB window register is not per pci-func for NX3031,
so caching can result in incorrect values.

Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>