sfrench/cifs-2.6.git
7 years agoMerge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git...
Linus Torvalds [Sat, 18 Oct 2014 17:24:26 +0000 (10:24 -0700)]
Merge tag 'modules-next-for-linus' of git://git./linux/kernel/git/rusty/linux

Pull module fix from Rusty Russell:
 "A single panic fix for a rare race, stable CC'd"

* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
  modules, lock around setting of MODULE_STATE_UNFORMED

7 years agoMAINTAINERS: Become the docs maintainer
Jonathan Corbet [Fri, 17 Oct 2014 12:59:26 +0000 (08:59 -0400)]
MAINTAINERS: Become the docs maintainer

It seems it's my turn to be the documentation maintainer for a bit.  My
plan is to work to ensure that docs patches don't fall through the cracks;
I assume most changes will continue to flow through subsystem-specific
trees.

Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
7 years agox86,kvm,vmx: Preserve CR4 across VM entry
Andy Lutomirski [Wed, 8 Oct 2014 16:02:13 +0000 (09:02 -0700)]
x86,kvm,vmx: Preserve CR4 across VM entry

CR4 isn't constant; at least the TSD and PCE bits can vary.

TBH, treating CR0 and CR3 as constant scares me a bit, too, but it looks
like it's correct.

This adds a branch and a read from cr4 to each vm entry.  Because it is
extremely likely that consecutive entries into the same vcpu will have
the same host cr4 value, this fixes up the vmcs instead of restoring cr4
after the fact.  A subsequent patch will add a kernel-wide cr4 shadow,
reducing the overhead in the common case to just two memory reads and a
branch.

Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: stable@vger.kernel.org
Cc: Petr Matousek <pmatouse@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
7 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Linus Torvalds [Sat, 18 Oct 2014 16:31:37 +0000 (09:31 -0700)]
Merge git://git./linux/kernel/git/davem/net

Pull networking fixes from David Miller:

 1) Include fixes for netrom and dsa (Fabian Frederick and Florian
    Fainelli)

 2) Fix FIXED_PHY support in stmmac, from Giuseppe CAVALLARO.

 3) Several SKB use after free fixes (vxlan, openvswitch, vxlan,
    ip_tunnel, fou), from Li ROngQing.

 4) fec driver PTP support fixes from Luwei Zhou and Nimrod Andy.

 5) Use after free in virtio_net, from Michael S Tsirkin.

 6) Fix flow mask handling for megaflows in openvswitch, from Pravin B
    Shelar.

 7) ISDN gigaset and capi bug fixes from Tilman Schmidt.

 8) Fix route leak in ip_send_unicast_reply(), from Vasily Averin.

 9) Fix two eBPF JIT bugs on x86, from Alexei Starovoitov.

10) TCP_SKB_CB() reorganization caused a few regressions, fixed by Cong
    Wang and Eric Dumazet.

11) Don't overwrite end of SKB when parsing malformed sctp ASCONF
    chunks, from Daniel Borkmann.

12) Don't call sock_kfree_s() with NULL pointers, this function also has
    the side effect of adjusting the socket memory usage.  From Cong Wang.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (90 commits)
  bna: fix skb->truesize underestimation
  net: dsa: add includes for ethtool and phy_fixed definitions
  openvswitch: Set flow-key members.
  netrom: use linux/uaccess.h
  dsa: Fix conversion from host device to mii bus
  tipc: fix bug in bundled buffer reception
  ipv6: introduce tcp_v6_iif()
  sfc: add support for skb->xmit_more
  r8152: return -EBUSY for runtime suspend
  ipv4: fix a potential use after free in fou.c
  ipv4: fix a potential use after free in ip_tunnel_core.c
  hyperv: Add handling of IP header with option field in netvsc_set_hash()
  openvswitch: Create right mask with disabled megaflows
  vxlan: fix a free after use
  openvswitch: fix a use after free
  ipv4: dst_entry leak in ip_send_unicast_reply()
  ipv4: clean up cookie_v4_check()
  ipv4: share tcp_v4_save_options() with cookie_v4_check()
  ipv4: call __ip_options_echo() in cookie_v4_check()
  atm: simplify lanai.c by using module_pci_driver
  ...

7 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc
Linus Torvalds [Sat, 18 Oct 2014 16:30:41 +0000 (09:30 -0700)]
Merge git://git./linux/kernel/git/davem/sparc

Pull Sparc bugfix from David Miller:
 "Sparc64 AES ctr mode bug fix"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc64: Fix FPU register corruption with AES crypto offload.

7 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide
Linus Torvalds [Sat, 18 Oct 2014 16:29:59 +0000 (09:29 -0700)]
Merge git://git./linux/kernel/git/davem/ide

Pull IDE cleanup from David Miller:
 "One IDE driver cleanup"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide:
  Drivers: ide: Remove typedef atiixp_ide_timing

7 years agofutex: Ensure get_futex_key_refs() always implies a barrier
Catalin Marinas [Fri, 17 Oct 2014 16:38:49 +0000 (17:38 +0100)]
futex: Ensure get_futex_key_refs() always implies a barrier

Commit b0c29f79ecea (futexes: Avoid taking the hb->lock if there's
nothing to wake up) changes the futex code to avoid taking a lock when
there are no waiters. This code has been subsequently fixed in commit
11d4616bd07f (futex: revert back to the explicit waiter counting code).
Both the original commit and the fix-up rely on get_futex_key_refs() to
always imply a barrier.

However, for private futexes, none of the cases in the switch statement
of get_futex_key_refs() would be hit and the function completes without
a memory barrier as required before checking the "waiters" in
futex_wake() -> hb_waiters_pending(). The consequence is a race with a
thread waiting on a futex on another CPU, allowing the waker thread to
read "waiters == 0" while the waiter thread to have read "futex_val ==
locked" (in kernel).

Without this fix, the problem (user space deadlocks) can be seen with
Android bionic's mutex implementation on an arm64 multi-cluster system.

Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Matteo Franchin <Matteo.Franchin@arm.com>
Fixes: b0c29f79ecea (futexes: Avoid taking the hb->lock if there's nothing to wake up)
Acked-by: Davidlohr Bueso <dave@stgolabs.net>
Tested-by: Mike Galbraith <umgwanakikbuti@gmail.com>
Cc: <stable@vger.kernel.org>
Cc: Darren Hart <dvhart@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
7 years agobna: fix skb->truesize underestimation
Eric Dumazet [Fri, 17 Oct 2014 19:45:55 +0000 (12:45 -0700)]
bna: fix skb->truesize underestimation

skb->truesize is not meant to be tracking amount of used bytes
in an skb, but amount of reserved/consumed bytes in memory.

For instance, if we use a single byte in last page fragment,
we have to account the full size of the fragment.

skb->truesize can be very different from skb->len, that has
a very specific safety purpose.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agonet: dsa: add includes for ethtool and phy_fixed definitions
Florian Fainelli [Fri, 17 Oct 2014 23:02:13 +0000 (16:02 -0700)]
net: dsa: add includes for ethtool and phy_fixed definitions

net/dsa/slave.c uses functions and structures declared in phy_fixed.h
but does not explicitely include it, while dsa.h needs structure
declarations for 'struct ethtool_wolinfo' and 'struct ethtool_eee', fix
those by including the correct header files.

Fixes: ec9436baedb6 ("net: dsa: allow drivers to do link adjustment")
Fixes: ce31b31c68e7 ("net: dsa: allow updating fixed PHY link information")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoopenvswitch: Set flow-key members.
Pravin B Shelar [Fri, 17 Oct 2014 20:56:31 +0000 (13:56 -0700)]
openvswitch: Set flow-key members.

This patch adds missing memset which are required to initialize
flow key member. For example for IP flow we need to initialize
ip.frag for all cases.

Found by inspection.

This bug is introduced by commit 0714812134d7dcadeb7ecfbfeb18788aa7e1eaac
("openvswitch: Eliminate memset() from flow_extract").

Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agonetrom: use linux/uaccess.h
Fabian Frederick [Fri, 17 Oct 2014 20:00:22 +0000 (22:00 +0200)]
netrom: use linux/uaccess.h

replace asm/uaccess.h by linux/uaccess.h

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agodsa: Fix conversion from host device to mii bus
Guenter Roeck [Fri, 17 Oct 2014 19:30:58 +0000 (12:30 -0700)]
dsa: Fix conversion from host device to mii bus

Commit b4d2394d01bc ("dsa: Replace mii_bus with a generic host device")
replaces mii_bus with a generic host_dev, and introduces
dsa_host_dev_to_mii_bus() to support conversion from host_dev to mii_bus.
However, in some cases it uses to_mii_bus to perform that conversion.
Since host_dev is not the phy bus device but typically a platform device,
this fails and results in a crash with the affected drivers.

BUG: unable to handle kernel NULL pointer dereference at           (null)
IP: [<ffffffff81781d35>] __mutex_lock_slowpath+0x75/0x100
PGD 406783067 PUD 406784067 PMD 0
Oops: 0002 [#1] SMP
...
Call Trace:
[<ffffffff810a538b>] ? pick_next_task_fair+0x61b/0x880
[<ffffffff81781de3>] mutex_lock+0x23/0x37
[<ffffffff81533244>] mdiobus_read+0x34/0x60
[<ffffffff8153b95a>] __mv88e6xxx_reg_read+0x8a/0xa0
[<ffffffff8153b9bc>] mv88e6xxx_reg_read+0x4c/0xa0

Fixes: b4d2394d01bc ("dsa: Replace mii_bus with a generic host device")
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agotipc: fix bug in bundled buffer reception
Jon Paul Maloy [Fri, 17 Oct 2014 19:25:28 +0000 (15:25 -0400)]
tipc: fix bug in bundled buffer reception

In commit ec8a2e5621db2da24badb3969eda7fd359e1869f ("tipc: same receive
code path for connection protocol and data messages") we omitted the
the possiblilty that an arriving message extracted from a bundle buffer
may be a multicast message. Such messages need to be to be delivered to
the socket via a separate function, tipc_sk_mcast_rcv(). As a result,
small multicast messages arriving as members of a bundle buffer will be
silently dropped.

This commit corrects the error by considering this case in the function
tipc_link_bundle_rcv().

Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoipv6: introduce tcp_v6_iif()
Eric Dumazet [Fri, 17 Oct 2014 16:17:20 +0000 (09:17 -0700)]
ipv6: introduce tcp_v6_iif()

Commit 971f10eca186 ("tcp: better TCP_SKB_CB layout to reduce cache line
misses") added a regression for SO_BINDTODEVICE on IPv6.

This is because we still use inet6_iif() which expects that IP6 control
block is still at the beginning of skb->cb[]

This patch adds tcp_v6_iif() helper and uses it where necessary.

Because __inet6_lookup_skb() is used by TCP and DCCP, we add an iif
parameter to it.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 971f10eca186 ("tcp: better TCP_SKB_CB layout to reduce cache line misses")
Acked-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agosfc: add support for skb->xmit_more
Edward Cree [Fri, 17 Oct 2014 14:32:25 +0000 (15:32 +0100)]
sfc: add support for skb->xmit_more

Don't ring the doorbell, and don't do PIO.  This will also prevent
 TX Push, because there will be more than one buffer waiting when
 the doorbell is rung.

Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agor8152: return -EBUSY for runtime suspend
hayeswang [Fri, 17 Oct 2014 08:55:08 +0000 (16:55 +0800)]
r8152: return -EBUSY for runtime suspend

Remove calling cancel_delayed_work_sync() for runtime suspend,
because it would cause dead lock. Instead, return -EBUSY to
avoid the device enters suspending if the net is running and
the delayed work is pending or running. The delayed work would
try to wake up the device later, so the suspending is not
necessary.

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoipv4: fix a potential use after free in fou.c
Li RongQing [Fri, 17 Oct 2014 08:53:47 +0000 (16:53 +0800)]
ipv4: fix a potential use after free in fou.c

pskb_may_pull() maybe change skb->data and make uh pointer oboslete,
so reload uh and guehdr

Fixes: 37dd0247 ("gue: Receive side for Generic UDP Encapsulation")
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoipv4: fix a potential use after free in ip_tunnel_core.c
Li RongQing [Fri, 17 Oct 2014 08:53:23 +0000 (16:53 +0800)]
ipv4: fix a potential use after free in ip_tunnel_core.c

pskb_may_pull() maybe change skb->data and make eth pointer oboslete,
so set eth after pskb_may_pull()

Fixes:3d7b46cd("ip_tunnel: push generic protocol handling to ip_tunnel module")
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agohyperv: Add handling of IP header with option field in netvsc_set_hash()
Haiyang Zhang [Thu, 16 Oct 2014 21:47:58 +0000 (14:47 -0700)]
hyperv: Add handling of IP header with option field in netvsc_set_hash()

In case that the IP header has optional field at the end, this patch will
get the port numbers after that field, and compute the hash. The general
parser skb_flow_dissect() is used here.

Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoopenvswitch: Create right mask with disabled megaflows
Pravin B Shelar [Fri, 17 Oct 2014 04:55:45 +0000 (21:55 -0700)]
openvswitch: Create right mask with disabled megaflows

If megaflows are disabled, the userspace does not send the netlink attribute
OVS_FLOW_ATTR_MASK, and the kernel must create an exact match mask.

sw_flow_mask_set() sets every bytes (in 'range') of the mask to 0xff, even the
bytes that represent padding for struct sw_flow, or the bytes that represent
fields that may not be set during ovs_flow_extract().
This is a problem, because when we extract a flow from a packet,
we do not memset() anymore the struct sw_flow to 0.

This commit gets rid of sw_flow_mask_set() and introduces mask_set_nlattr(),
which operates on the netlink attributes rather than on the mask key. Using
this approach we are sure that only the bytes that the user provided in the
flow are matched.

Also, if the parse_flow_mask_nlattrs() for the mask ENCAP attribute fails, we
now return with an error.

This bug is introduced by commit 0714812134d7dcadeb7ecfbfeb18788aa7e1eaac
("openvswitch: Eliminate memset() from flow_extract").

Reported-by: Alex Wang <alexw@nicira.com>
Signed-off-by: Daniele Di Proietto <ddiproietto@vmware.com>
Signed-off-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agovxlan: fix a free after use
Li RongQing [Fri, 17 Oct 2014 06:06:16 +0000 (14:06 +0800)]
vxlan: fix a free after use

pskb_may_pull maybe change skb->data and make eth pointer oboslete,
so eth needs to reload

Fixes: 91269e390d062 ("vxlan: using pskb_may_pull as early as possible")
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoopenvswitch: fix a use after free
Li RongQing [Fri, 17 Oct 2014 06:03:08 +0000 (14:03 +0800)]
openvswitch: fix a use after free

pskb_may_pull() called by arphdr_ok can change skb->data, so put the arp
setting after arphdr_ok to avoid the use the freed memory

Fixes: 0714812134d7d ("openvswitch: Eliminate memset() from flow_extract.")
Cc: Jesse Gross <jesse@nicira.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoipv4: dst_entry leak in ip_send_unicast_reply()
Vasily Averin [Wed, 15 Oct 2014 12:24:02 +0000 (16:24 +0400)]
ipv4: dst_entry leak in ip_send_unicast_reply()

ip_setup_cork() called inside ip_append_data() steals dst entry from rt to cork
and in case errors in __ip_append_data() nobody frees stolen dst entry

Fixes: 2e77d89b2fa8 ("net: avoid a pair of dst_hold()/dst_release() in ip_append_data()")
Signed-off-by: Vasily Averin <vvs@parallels.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoipv4: clean up cookie_v4_check()
Cong Wang [Wed, 15 Oct 2014 21:33:22 +0000 (14:33 -0700)]
ipv4: clean up cookie_v4_check()

We can retrieve opt from skb, no need to pass it as a parameter.
And opt should always be non-NULL, no need to check.

Cc: Krzysztof Kolasa <kkolasa@winsoft.pl>
Cc: Eric Dumazet <edumazet@google.com>
Tested-by: Krzysztof Kolasa <kkolasa@winsoft.pl>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoipv4: share tcp_v4_save_options() with cookie_v4_check()
Cong Wang [Wed, 15 Oct 2014 21:33:21 +0000 (14:33 -0700)]
ipv4: share tcp_v4_save_options() with cookie_v4_check()

cookie_v4_check() allocates ip_options_rcu in the same way
with tcp_v4_save_options(), we can just make it a helper function.

Cc: Krzysztof Kolasa <kkolasa@winsoft.pl>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoipv4: call __ip_options_echo() in cookie_v4_check()
Cong Wang [Wed, 15 Oct 2014 21:33:20 +0000 (14:33 -0700)]
ipv4: call __ip_options_echo() in cookie_v4_check()

commit 971f10eca186cab238c49da ("tcp: better TCP_SKB_CB layout to reduce cache line misses")
missed that cookie_v4_check() still calls ip_options_echo() which uses
IPCB(). It should use TCPCB() at TCP layer, so call __ip_options_echo()
instead.

Fixes: commit 971f10eca186cab238c49da ("tcp: better TCP_SKB_CB layout to reduce cache line misses")
Cc: Krzysztof Kolasa <kkolasa@winsoft.pl>
Cc: Eric Dumazet <edumazet@google.com>
Reported-by: Krzysztof Kolasa <kkolasa@winsoft.pl>
Tested-by: Krzysztof Kolasa <kkolasa@winsoft.pl>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoatm: simplify lanai.c by using module_pci_driver
Michael Opdenacker [Wed, 15 Oct 2014 07:45:50 +0000 (09:45 +0200)]
atm: simplify lanai.c by using module_pci_driver

This simplifies the lanai.c driver by using
the module_pci_driver() macro, at the expense
of losing only debugging messages.

Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agonetlink: fix description of portid
Nicolas Dichtel [Thu, 16 Oct 2014 13:47:51 +0000 (15:47 +0200)]
netlink: fix description of portid

Avoid confusion between pid and portid.

Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoMerge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net
David S. Miller [Thu, 16 Oct 2014 18:42:51 +0000 (14:42 -0400)]
Merge branch 'master' of git://git./linux/kernel/git/jkirsher/net

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2014-10-16

This series contains updates to fm10k and ixgbe.

Matthew provides two fixes for fm10k, first sets the flag to fetch the
host state before kicking off the service task that reads the host
state when bringing the interface up.  The second makes sure that we
release the mailbox lock after detecting an error and before we return
the error code.

Andy Zhou provides a compile fix for fm10k, when the driver is compiled
into the kernel and the VXLAN driver is compiled as a module.

Emil provides a fix for ixgbe to prevent against a panic by trying
to dereference a NULL pointer in ixgbe_ndo_set_vf_spoofchk().
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoixgbe: check for vfs outside of sriov_num_vfs before dereference
Emil Tantilov [Thu, 16 Oct 2014 15:49:02 +0000 (15:49 +0000)]
ixgbe: check for vfs outside of sriov_num_vfs before dereference

The check for vfinfo is not sufficient because it does not protect
against specifying vf that is outside of sriov_num_vfs range.
All of the ndo functions have a check for it except for
ixgbevf_ndo_set_spoofcheck().

The following patch is all we need to protect against this panic:

ip link set p96p1 vf 0 spoofchk off
BUG: unable to handle kernel NULL pointer dereference at 0000000000000052
IP: [<ffffffffa044a1c1>]
ixgbe_ndo_set_vf_spoofchk+0x51/0x150 [ixgbe]

Reported-by: Thierry Herbelot <thierry.herbelot@6wind.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Acked-by: Thierry Herbelot <thierry.herbelot@6wind.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
7 years agofm10k: Add CONFIG_FM10K_VXLAN configuration option
Andy Zhou [Sat, 4 Oct 2014 06:19:11 +0000 (06:19 +0000)]
fm10k: Add CONFIG_FM10K_VXLAN configuration option

Compiling with CONFIG_FM10K=y and VXLAN=m resulting in linking error:

   drivers/built-in.o: In function `fm10k_open':
   (.text+0x1f9d7a): undefined reference to `vxlan_get_rx_port'
   make: *** [vmlinux] Error 1

The fix follows the same strategy as I40E.

Signed-off-by: Andy Zhou <azhou@nicira.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
7 years agofm10k: Unlock mailbox on VLAN addition failures
Matthew Vick [Fri, 3 Oct 2014 00:43:35 +0000 (00:43 +0000)]
fm10k: Unlock mailbox on VLAN addition failures

After grabbing the mailbox lock and detecting an error, the lock must be
released before the error code can be returned.

Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
7 years agofm10k: Check the host state when bringing the interface up
Matthew Vick [Thu, 2 Oct 2014 05:10:18 +0000 (05:10 +0000)]
fm10k: Check the host state when bringing the interface up

Set the flag to fetch the host state before kicking off the service task
that reads the host state when bringing the interface back up.

Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
7 years agovxlan: using pskb_may_pull as early as possible
Li RongQing [Thu, 16 Oct 2014 01:17:18 +0000 (09:17 +0800)]
vxlan: using pskb_may_pull as early as possible

pskb_may_pull should be used to check if skb->data has enough space,
skb->len can not ensure that.

Cc: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agovxlan: fix a use after free in vxlan_encap_bypass
Li RongQing [Thu, 16 Oct 2014 00:49:41 +0000 (08:49 +0800)]
vxlan: fix a use after free in vxlan_encap_bypass

when netif_rx() is done, the netif_rx handled skb maybe be freed,
and should not be used.

Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoopenvswitch: use vport instead of p
Fabian Frederick [Wed, 15 Oct 2014 19:03:41 +0000 (21:03 +0200)]
openvswitch: use vport instead of p

All functions used struct vport *vport except
ovs_vport_find_upcall_portid.

This fixes 1 kerneldoc warning

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoopenvswitch: kerneldoc warning fix
Fabian Frederick [Wed, 15 Oct 2014 19:03:18 +0000 (21:03 +0200)]
openvswitch: kerneldoc warning fix

s/sock/gs

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agogianfar: Add FCS to rx buffer size (fix)
Claudiu Manoil [Wed, 15 Oct 2014 16:11:46 +0000 (19:11 +0300)]
gianfar: Add FCS to rx buffer size (fix)

For each Rx frame the eTSEC writes its FCS (Frame Check Sequence)
to the Rx buffer.

The eTSEC h/w manual states in the "Receive Buffer Descriptor Field
Descriptions" table:
"Data length is the number of octets written by the eTSEC into this BD's
data buffer if L is cleared (the value is equal to MRBLR), or, if L is
set, the length of the frame including *CRC*, FCB (if RCTRL[PRSDEP > 00),
preamble (if MACCFG2[PreAmRxEn]=1), time stamp (if RCTRL[TS] = 1) and
any padding (RCTRL[PAL])."

Though the FCS bytes are removed by the driver before passing the skb
to the net stack, the Rx buffer size computation does not currently
take into account the FCS bytes (4 bytes).
Because the Rx buffer size is multiple of 512 bytes, leaving out the
FCS is not a problem for the default MTU of 1500, as the Rx buffer size
is 1536 in this case.  However, for custom MTUs, where the difference
between the MTU size and the Rx buffer size is less, this can be a
problem as the computed Rx buffer size won't be enough to accomodate
the FCS for a received frame that is big enough (close to MTU size).
In such case the received frame is considered to be incomplete (L flag
not set in the RxBD status) and silently dropped.

Note that the driver does not currently support S/G on Rx, so it has to
compute its Rx buffer size based on the MTU of the device.

Reported-by: Kristian Otnes <kotnes@cisco.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agovirtio_net: fix use after free
Michael S. Tsirkin [Wed, 15 Oct 2014 13:23:28 +0000 (16:23 +0300)]
virtio_net: fix use after free

commit 0b725a2ca61bedc33a2a63d0451d528b268cf975
    net: Remove ndo_xmit_flush netdev operation, use signalling instead.

added code that looks at skb->xmit_more after the skb has
been put in TX VQ. Since some paths process the ring and free the skb
immediately, this can cause use after free.

Fix by storing xmit_more in a local variable.

Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agonet: fec: ptp: fix convergence issue to support LinuxPTP stack
Nimrod Andy [Wed, 15 Oct 2014 09:30:12 +0000 (17:30 +0800)]
net: fec: ptp: fix convergence issue to support LinuxPTP stack

iMX6SX IEEE 1588 module has one hw issue in capturing the ATVR register.
The current SW flow is:
ENET0->ATCR |= ENET_ATCR_CAPTURE_MASK;
ts_counter_ns = ENET0->ATVR;
The ATVR value is not expected value that cause LinuxPTP stack cannot be convergent.

ENET Block Guide/ Chapter for the iMX6SX (PELE) address the issue:
After set ENET_ATCR[Capture], there need some time cycles before the counter
value is capture in the register clock domain. The wait-time-cycles is at least
6 clock cycles of the slower clock between the register clock and the 1588 clock.
So need something like:
ENET0->ATCR |= ENET_ATCR_CAPTURE_MASK;
wait();
ts_counter_ns = ENET0->ATVR;

For iMX6SX, the 1588 ts_clk is fixed to 25Mhz, register clock is 66Mhz, so the
wait-time-cycles must be greater than 240ns (40ns * 6). The patch add 1us delay
before cpu read ATVR register.

Changes V2:
Modify the commit/comments log to describe the issue clearly.

Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoDrivers: ide: Remove typedef atiixp_ide_timing
Himangi Saraogi [Thu, 14 Aug 2014 16:44:30 +0000 (22:14 +0530)]
Drivers: ide: Remove typedef atiixp_ide_timing

The Linux kernel coding style guidelines suggest not using typedefs
for structure types. This patch gets rid of the typedef for
atiixp_ide_timing.

The following Coccinelle semantic patch detects the case:

@tn1@
type td;
@@

typedef struct { ... } td;

@script:python tf@
td << tn1.td;
tdres;
@@

coccinelle.tdres = td;

@@
type tn1.td;
identifier tf.tdres;
@@

-typedef
 struct
+  tdres
   { ... }
-td
 ;

@@
type tn1.td;
identifier tf.tdres;
@@

-td
+ struct tdres

Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agocxgb4i : Fix -Wmaybe-uninitialized warning.
Anish Bhatt [Wed, 15 Oct 2014 07:26:47 +0000 (00:26 -0700)]
cxgb4i : Fix -Wmaybe-uninitialized warning.

Identified by kbuild test robot. csk family is always set to be AF_INET or
AF_INET6, so skb will always be initialized to some value but there is no harm
in silencing the warning anyways.

Signed-off-by: Anish Bhatt <anish@chelsio.com>
Fixes : f42bb57c61fd ('cxgb4i : Fix -Wunused-function warning')
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agonet: Add ndo_gso_check
Tom Herbert [Tue, 14 Oct 2014 22:19:06 +0000 (15:19 -0700)]
net: Add ndo_gso_check

Add ndo_gso_check which a device can define to indicate whether is
is capable of doing GSO on a packet. This funciton would be called from
the stack to determine whether software GSO is needed to be done. A
driver should populate this function if it advertises GSO types for
which there are combinations that it wouldn't be able to handle. For
instance a device that performs UDP tunneling might only implement
support for transparent Ethernet bridging type of inner packets
or might have limitations on lengths of inner headers.

Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agostmmac: fix sti compatibililies
Giuseppe CAVALLARO [Wed, 15 Oct 2014 05:30:41 +0000 (07:30 +0200)]
stmmac: fix sti compatibililies

this patch is to fix the stmmac data compatibilities for
all the SoCs inside the platform file.

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoMerge branch 'for-3.18-consistent-ops' of git://git.kernel.org/pub/scm/linux/kernel...
Linus Torvalds [Wed, 15 Oct 2014 05:48:18 +0000 (07:48 +0200)]
Merge branch 'for-3.18-consistent-ops' of git://git./linux/kernel/git/tj/percpu

Pull percpu consistent-ops changes from Tejun Heo:
 "Way back, before the current percpu allocator was implemented, static
  and dynamic percpu memory areas were allocated and handled separately
  and had their own accessors.  The distinction has been gone for many
  years now; however, the now duplicate two sets of accessors remained
  with the pointer based ones - this_cpu_*() - evolving various other
  operations over time.  During the process, we also accumulated other
  inconsistent operations.

  This pull request contains Christoph's patches to clean up the
  duplicate accessor situation.  __get_cpu_var() uses are replaced with
  with this_cpu_ptr() and __this_cpu_ptr() with raw_cpu_ptr().

  Unfortunately, the former sometimes is tricky thanks to C being a bit
  messy with the distinction between lvalues and pointers, which led to
  a rather ugly solution for cpumask_var_t involving the introduction of
  this_cpu_cpumask_var_ptr().

  This converts most of the uses but not all.  Christoph will follow up
  with the remaining conversions in this merge window and hopefully
  remove the obsolete accessors"

* 'for-3.18-consistent-ops' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (38 commits)
  irqchip: Properly fetch the per cpu offset
  percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t -fix
  ia64: sn_nodepda cannot be assigned to after this_cpu conversion. Use __this_cpu_write.
  percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t
  Revert "powerpc: Replace __get_cpu_var uses"
  percpu: Remove __this_cpu_ptr
  clocksource: Replace __this_cpu_ptr with raw_cpu_ptr
  sparc: Replace __get_cpu_var uses
  avr32: Replace __get_cpu_var with __this_cpu_write
  blackfin: Replace __get_cpu_var uses
  tile: Use this_cpu_ptr() for hardware counters
  tile: Replace __get_cpu_var uses
  powerpc: Replace __get_cpu_var uses
  alpha: Replace __get_cpu_var
  ia64: Replace __get_cpu_var uses
  s390: cio driver &__get_cpu_var replacements
  s390: Replace __get_cpu_var uses
  mips: Replace __get_cpu_var uses
  MIPS: Replace __get_cpu_var uses in FPU emulator.
  arm: Replace __this_cpu_ptr with raw_cpu_ptr
  ...

7 years agoMerge tag 'llvmlinux-for-v3.18' of git://git.linuxfoundation.org/llvmlinux/kernel
Linus Torvalds [Wed, 15 Oct 2014 05:30:52 +0000 (07:30 +0200)]
Merge tag 'llvmlinux-for-v3.18' of git://git.linuxfoundation.org/llvmlinux/kernel

Pull LLVM updates from Behan Webster:
 "These patches remove the use of VLAIS using a new SHASH_DESC_ON_STACK
  macro.

  Some of the previously accepted VLAIS removal patches haven't used
  this macro.  I will push new patches to consistently use this macro in
  all those older cases for 3.19"

[ More LLVM patches coming in through subsystem trees, and LLVM itself
  needs some fixes that are already in many distributions but not in
  released versions of LLVM.  Some day this will all "just work"  - Linus ]

* tag 'llvmlinux-for-v3.18' of git://git.linuxfoundation.org/llvmlinux/kernel:
  crypto: LLVMLinux: Remove VLAIS usage from crypto/testmgr.c
  security, crypto: LLVMLinux: Remove VLAIS from ima_crypto.c
  crypto: LLVMLinux: Remove VLAIS usage from libcrc32c.c
  crypto: LLVMLinux: Remove VLAIS usage from crypto/hmac.c
  crypto, dm: LLVMLinux: Remove VLAIS usage from dm-crypt
  crypto: LLVMLinux: Remove VLAIS from crypto/.../qat_algs.c
  crypto: LLVMLinux: Remove VLAIS from crypto/omap_sham.c
  crypto: LLVMLinux: Remove VLAIS from crypto/n2_core.c
  crypto: LLVMLinux: Remove VLAIS from crypto/mv_cesa.c
  crypto: LLVMLinux: Remove VLAIS from crypto/ccp/ccp-crypto-sha.c
  btrfs: LLVMLinux: Remove VLAIS
  crypto: LLVMLinux: Add macro to remove use of VLAIS in crypto code

7 years agoMerge tag 'iommu-updates-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git...
Linus Torvalds [Wed, 15 Oct 2014 05:23:49 +0000 (07:23 +0200)]
Merge tag 'iommu-updates-v3.18' of git://git./linux/kernel/git/joro/iommu

Pull IOMMU updates from Joerg Roedel:
 "This pull-request includes:

   - change in the IOMMU-API to convert the former iommu_domain_capable
     function to just iommu_capable

   - various fixes in handling RMRR ranges for the VT-d driver (one fix
     requires a device driver core change which was acked by Greg KH)

   - the AMD IOMMU driver now assigns and deassigns complete alias
     groups to fix issues with devices using the wrong PCI request-id

   - MMU-401 support for the ARM SMMU driver

   - multi-master IOMMU group support for the ARM SMMU driver

   - various other small fixes all over the place"

* tag 'iommu-updates-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (41 commits)
  iommu/vt-d: Work around broken RMRR firmware entries
  iommu/vt-d: Store bus information in RMRR PCI device path
  iommu/vt-d: Only remove domain when device is removed
  driver core: Add BUS_NOTIFY_REMOVED_DEVICE event
  iommu/amd: Fix devid mapping for ivrs_ioapic override
  iommu/irq_remapping: Fix the regression of hpet irq remapping
  iommu: Fix bus notifier breakage
  iommu/amd: Split init_iommu_group() from iommu_init_device()
  iommu: Rework iommu_group_get_for_pci_dev()
  iommu: Make of_device_id array const
  amd_iommu: do not dereference a NULL pointer address.
  iommu/omap: Remove omap_iommu unused owner field
  iommu: Remove iommu_domain_has_cap() API function
  IB/usnic: Convert to use new iommu_capable() API function
  vfio: Convert to use new iommu_capable() API function
  kvm: iommu: Convert to use new iommu_capable() API function
  iommu/tegra: Convert to iommu_capable() API function
  iommu/msm: Convert to iommu_capable() API function
  iommu/vt-d: Convert to iommu_capable() API function
  iommu/fsl: Convert to iommu_capable() API function
  ...

7 years agoMerge tag 'clk-for-linus-3.18' of git://git.linaro.org/people/mike.turquette/linux
Linus Torvalds [Wed, 15 Oct 2014 05:05:03 +0000 (07:05 +0200)]
Merge tag 'clk-for-linus-3.18' of git://git.linaro.org/people/mike.turquette/linux

Pull clock tree updates from Mike Turquette:
 "The clk tree changes for 3.18 are dominated by clock drivers.  Mostly
  fixes and enhancements to existing drivers as well as new drivers.
  This tag contains a bit more arch code than I usually take due to some
  OMAP2+ changes.  Additionally it contains the restart notifier
  handlers which are merged as a dependency into several trees.

  The PXA changes are the only messy part.  Due to having a stable tree
  I had to revert one patch and follow up with one more fix near the tip
  of this tag.  Some dead code is introduced but it will soon become
  live code after 3.18-rc1 is released as the rest of the PXA family is
  converted over to the common clock framework.

  Another trend in this tag is that multiple vendors have started to
  push the complexity of changing their CPU frequency into the clock
  driver, whereas this used to be done in CPUfreq drivers.

  Changes to the clk core include a generic gpio-clock type and a
  clk_set_phase() function added to the top-level clk.h api.  Due to
  some confusion on the fbdev mailing list the kernel boot parameters
  documentation was updated to further explain the clk_ignore_unused
  parameter, which is often required by users of the simplefb driver.

  Finally some fixes to the locking around the clock debugfs stuff was
  done to prevent deadlocks when interacting with other subsystems."

* tag 'clk-for-linus-3.18' of git://git.linaro.org/people/mike.turquette/linux: (99 commits)
  clk: pxa clocks build system fix
  Revert "arm: pxa: Transition pxa27x to clk framework"
  clk: samsung: register restart handlers for s3c2412 and s3c2443
  clk: rockchip: add restart handler
  clk: rockchip: rk3288: i2s_frac adds flag to set parent's rate
  doc/kernel-parameters.txt: clarify clk_ignore_unused
  arm: pxa: Transition pxa27x to clk framework
  dts: add devicetree bindings for pxa27x clocks
  clk: add pxa27x clock drivers
  arm: pxa: add clock pll selection bits
  clk: dts: document pxa clock binding
  clk: add pxa clocks infrastructure
  clk: gpio-gate: Ensure gpiod_ APIs are prototyped
  clk: ti: dra7-atl-clock: Mark the device as pm_runtime_irq_safe
  clk: ti: LLVMLinux: Move __init outside of type definition
  clk: ti: consider the fact that of_clk_get() might return an error
  clk: ti: dra7-atl-clock: fix a memory leak
  clk: ti: change clock init to use generic of_clk_init
  clk: hix5hd2: add I2C clocks
  clk: hix5hd2: add watchdog0 clocks
  ...

7 years agoMerge tag 'mfd-for-linus-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Linus Torvalds [Wed, 15 Oct 2014 04:58:16 +0000 (06:58 +0200)]
Merge tag 'mfd-for-linus-3.18' of git://git./linux/kernel/git/lee/mfd

Pull MFD updates from Lee Jones:
 "Changes to existing drivers:
  - DT clean-ups in da9055-core, max14577, rn5t618, arizona, hi6421, stmpe, twl4030
  - Export symbols for use in modules in max14577
  - Plenty of static code analysis/Coccinelle fixes throughout the SS
  - Regmap clean-ups in arizona, wm5102, wm5110, da9052, tps65217, rk808
  - Remove unused/duplicate code in da9052, 88pm860x, ti_ssp, lpc_sch, arizona
  - Bug fixes in ti_am335x_tscadc, da9052, ti_am335x_tscadc, rtsx_pcr
  - IRQ fixups in arizona, stmpe, max14577
  - Regulator related changes in axp20x
  - Pass DMA coherency information from parent => child in MFD core
  - Rename DT document files for consistency
  - Add ACPI support to the MFD core
  - Add Andreas Werner to MAINTAINERS for MEN F21BMC

 New drivers/supported devices:
  - New driver for MEN 14F021P00 Board Management Controller
  - New driver for Ricoh RN5T618 PMIC
  - New driver for Rockchip RK808
  - New driver for HiSilicon Hi6421 PMIC
  - New driver for Qualcomm SPMI PMICs
  - Add support for Intel Braswell in lpc_ich
  - Add support for Intel 9 Series PCH in lpc_ich
  - Add support for Intel Quark ILB in lpc_sch"

[ Delayed to after the poweer/reset pull due to Kconfig problems with
  recursive Kconfig select/depends-on chains.   - Linus ]

* tag 'mfd-for-linus-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (79 commits)
  mfd: cros_ec: wait for completion of commands that return IN_PROGRESS
  i2c: i2c-cros-ec-tunnel: Set retries to 3
  mfd: cros_ec: move locking into cros_ec_cmd_xfer
  mfd: cros_ec: stop calling ->cmd_xfer() directly
  mfd: cros_ec: Delay for 50ms when we see EC_CMD_REBOOT_EC
  MAINTAINERS: Adds Andreas Werner to maintainers list for MEN F21BMC
  mfd: arizona: Correct mask to allow setting micbias external cap
  mfd: Add ACPI support
  Revert "mfd: wm5102: Manually apply register patch"
  mfd: ti_am335x_tscadc: Update logic in CTRL register for 5-wire TS
  mfd: dt-bindings: atmel-gpbr: Rename doc file to conform to naming convention
  mfd: dt-bindings: qcom-pm8xxx: Rename doc file to conform to naming convention
  mfd: Inherit coherent_dma_mask from parent device
  mfd: Document DT bindings for Qualcomm SPMI PMICs
  mfd: Add support for Qualcomm SPMI PMICs
  mfd: dt-bindings: pm8xxx: Add new compatible string
  mfd: axp209x: Drop the parent supplies field
  mfd: twl4030-power: Use 'ti,system-power-controller' as alternative way to support system power off
  mfd: dt-bindings: twl4030-power: Use the standard property to mark power control
  mfd: syscon: Add Atmel GPBR DT bindings documention
  ...

7 years agoMerge tag 'for-v3.18' of git://git.infradead.org/battery-2.6
Linus Torvalds [Wed, 15 Oct 2014 04:56:23 +0000 (06:56 +0200)]
Merge tag 'for-v3.18' of git://git.infradead.org/battery-2.6

Pull power supply and reset updates from Sebastian Reichel:
 - Initial support for the following chips
   * max77836 (charger)
   * max14577 (charger)
   * bq27742 (battery gauge)
   * ltc2952 (poweroff)
   * stih416 (restart)
   * syscon-reboot (restart)
   * gpio-restart (restart)
 - cleanup of power supply core
 - misc fixes in power supply and reset drivers

* tag 'for-v3.18' of git://git.infradead.org/battery-2.6: (48 commits)
  power: ab8500_fg: Fix build warning
  Documentation: charger: max14577: Update the date of introducing ABI
  power: reset: corrections for simple syscon reboot driver
  Documentation: power: reset: Add documentation for generic SYSCON reboot driver
  power: reset: Add generic SYSCON register mapped reset
  bq27x00_battery: Fix flag reading for bq27742
  power: reset: use restart_notifier mechanism for msm-poweroff
  power: Add simple gpio-restart driver
  power: reset: st: Provide DT bindings for ST's Power Reset driver
  power: reset: Add restart functionality for STiH41x platforms
  power: charger-manager: Fix NULL pointer exception with missing cm-fuel-gauge
  power: max14577: Fix circular config SYSFS dependency
  power: gpio-charger: do not use gpio value directly
  power: max8925: Use of_get_child_by_name
  power: max8925: Fix NULL ptr dereference on memory allocation failure
  bq27x00_battery: Add support to bq27742
  Documentation: charger: max14577: Document exported sysfs entry
  devicetree: mfd: max14577: Add device tree bindings document
  power: max17040: Add ID for MAX77836 Fuel Gauge block
  charger: max14577: Configure battery-dependent settings from DTS and sysfs
  ...

Conflicts:
drivers/power/reset/Kconfig
drivers/power/reset/Makefile

7 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph...
Linus Torvalds [Wed, 15 Oct 2014 04:46:01 +0000 (06:46 +0200)]
Merge branch 'for-linus' of git://git./linux/kernel/git/sage/ceph-client

Pull Ceph updates from Sage Weil:
 "There is the long-awaited discard support for RBD (Guangliang Zhao,
  Josh Durgin), a pile of RBD bug fixes that didn't belong in late -rc's
  (Ilya Dryomov, Li RongQing), a pile of fs/ceph bug fixes and
  performance and debugging improvements (Yan, Zheng, John Spray), and a
  smattering of cleanups (Chao Yu, Fabian Frederick, Joe Perches)"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (40 commits)
  ceph: fix divide-by-zero in __validate_layout()
  rbd: rbd workqueues need a resque worker
  libceph: ceph-msgr workqueue needs a resque worker
  ceph: fix bool assignments
  libceph: separate multiple ops with commas in debugfs output
  libceph: sync osd op definitions in rados.h
  libceph: remove redundant declaration
  ceph: additional debugfs output
  ceph: export ceph_session_state_name function
  ceph: include the initial ACL in create/mkdir/mknod MDS requests
  ceph: use pagelist to present MDS request data
  libceph: reference counting pagelist
  ceph: fix llistxattr on symlink
  ceph: send client metadata to MDS
  ceph: remove redundant code for max file size verification
  ceph: remove redundant io_iter_advance()
  ceph: move ceph_find_inode() outside the s_mutex
  ceph: request xattrs if xattr_version is zero
  rbd: set the remaining discard properties to enable support
  rbd: use helpers to handle discard for layered images correctly
  ...

7 years agoMerge branch 'CVE-2014-7970' of git://git.kernel.org/pub/scm/linux/kernel/git/luto...
Linus Torvalds [Wed, 15 Oct 2014 04:43:27 +0000 (06:43 +0200)]
Merge branch 'CVE-2014-7970' of git://git./linux/kernel/git/luto/linux

Pull pivot_root() fix from Andy Lutomirski.

Prevent a leak of unreachable mounts.

* 'CVE-2014-7970' of git://git.kernel.org/pub/scm/linux/kernel/git/luto/linux:
  mnt: Prevent pivot_root from creating a loop in the mount tree

7 years agoMerge branch 'cxgb4'
David S. Miller [Wed, 15 Oct 2014 04:29:08 +0000 (00:29 -0400)]
Merge branch 'cxgb4'

Anish Bhatt says:

====================
ipv6 and related cleanup for cxgb4/cxgb4i

This patch set removes some duplicated/extraneous code from cxgb4i, guards
cxgb4 against compilation failure based on ipv6 tristate, make ipv6 related
code no longer be enabled by default irrespective of ipv6 tristate and fixes
a refcnt issue.
-Anish

v2 : Provide more detailed commit messages, make subject more concise as
recommended by Dave Miller.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agocxgb4i: Remove duplicate call to dst_neigh_lookup()
Anish Bhatt [Wed, 15 Oct 2014 03:07:24 +0000 (20:07 -0700)]
cxgb4i: Remove duplicate call to dst_neigh_lookup()

There is an extra call to dst_neigh_lookup() leftover in cxgb4i that can cause
an unreleased refcnt issue. Remove extraneous call.

Signed-off-by: Anish Bhatt <anish@chelsio.com>
Fixes : 759a0cc5a3e1b ('cxgb4i: Add ipv6 code to driver, call into libcxgbi ipv6 api')
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agocxgb4i : Fix -Wunused-function warning
Anish Bhatt [Wed, 15 Oct 2014 03:07:23 +0000 (20:07 -0700)]
cxgb4i : Fix -Wunused-function warning

A bunch of ipv6 related code is left on by default. While this causes no
compilation issues, there is no need to have this enabled by default. Guard
with an ipv6 check, which also takes care of a -Wunused-function warning.

Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agocxgb4 : Fix build failure in cxgb4 when ipv6 is disabled/not in-built
Anish Bhatt [Wed, 15 Oct 2014 03:07:22 +0000 (20:07 -0700)]
cxgb4 : Fix build failure in cxgb4 when ipv6 is disabled/not in-built

cxgb4 ipv6 does not guard against ipv6 being disabled, or the standard
ipv6 module vs inbuilt tri-state issue. This was fixed for cxgb4i & iw_cxgb4
but missed for cxgb4.

Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agocxgb4i : Remove duplicated CLIP handling code
Anish Bhatt [Wed, 15 Oct 2014 03:07:21 +0000 (20:07 -0700)]
cxgb4i : Remove duplicated CLIP handling code

cxgb4 already handles CLIP updates from a previous changeset for iw_cxgb4,
there is no need to have this functionality in cxgb4i. Remove duplicated code

Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agosparc64: Fix FPU register corruption with AES crypto offload.
David S. Miller [Wed, 15 Oct 2014 02:37:58 +0000 (19:37 -0700)]
sparc64: Fix FPU register corruption with AES crypto offload.

The AES loops in arch/sparc/crypto/aes_glue.c use a scheme where the
key material is preloaded into the FPU registers, and then we loop
over and over doing the crypt operation, reusing those pre-cooked key
registers.

There are intervening blkcipher*() calls between the crypt operation
calls.  And those might perform memcpy() and thus also try to use the
FPU.

The sparc64 kernel FPU usage mechanism is designed to allow such
recursive uses, but with a catch.

There has to be a trap between the two FPU using threads of control.

The mechanism works by, when the FPU is already in use by the kernel,
allocating a slot for FPU saving at trap time.  Then if, within the
trap handler, we try to use the FPU registers, the pre-trap FPU
register state is saved into the slot.  Then at trap return time we
notice this and restore the pre-trap FPU state.

Over the long term there are various more involved ways we can make
this work, but for a quick fix let's take advantage of the fact that
the situation where this happens is very limited.

All sparc64 chips that support the crypto instructiosn also are using
the Niagara4 memcpy routine, and that routine only uses the FPU for
large copies where we can't get the source aligned properly to a
multiple of 8 bytes.

We look to see if the FPU is already in use in this context, and if so
we use the non-large copy path which only uses integer registers.

Furthermore, we also limit this special logic to when we are doing
kernel copy, rather than a user copy.

Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agomodules, lock around setting of MODULE_STATE_UNFORMED
Prarit Bhargava [Mon, 13 Oct 2014 16:21:39 +0000 (02:51 +1030)]
modules, lock around setting of MODULE_STATE_UNFORMED

A panic was seen in the following sitation.

There are two threads running on the system. The first thread is a system
monitoring thread that is reading /proc/modules. The second thread is
loading and unloading a module (in this example I'm using my simple
dummy-module.ko).  Note, in the "real world" this occurred with the qlogic
driver module.

When doing this, the following panic occurred:

 ------------[ cut here ]------------
 kernel BUG at kernel/module.c:3739!
 invalid opcode: 0000 [#1] SMP
 Modules linked in: binfmt_misc sg nfsv3 rpcsec_gss_krb5 nfsv4 dns_resolver nfs fscache intel_powerclamp coretemp kvm_intel kvm crct10dif_pclmul crc32_pclmul crc32c_intel ghash_clmulni_intel aesni_intel lrw igb gf128mul glue_helper iTCO_wdt iTCO_vendor_support ablk_helper ptp sb_edac cryptd pps_core edac_core shpchp i2c_i801 pcspkr wmi lpc_ich ioatdma mfd_core dca ipmi_si nfsd ipmi_msghandler auth_rpcgss nfs_acl lockd sunrpc xfs libcrc32c sr_mod cdrom sd_mod crc_t10dif crct10dif_common mgag200 syscopyarea sysfillrect sysimgblt i2c_algo_bit drm_kms_helper ttm isci drm libsas ahci libahci scsi_transport_sas libata i2c_core dm_mirror dm_region_hash dm_log dm_mod [last unloaded: dummy_module]
 CPU: 37 PID: 186343 Comm: cat Tainted: GF          O--------------   3.10.0+ #7
 Hardware name: Intel Corporation S2600CP/S2600CP, BIOS RMLSDP.86I.00.29.D696.1311111329 11/11/2013
 task: ffff8807fd2d8000 ti: ffff88080fa7c000 task.ti: ffff88080fa7c000
 RIP: 0010:[<ffffffff810d64c5>]  [<ffffffff810d64c5>] module_flags+0xb5/0xc0
 RSP: 0018:ffff88080fa7fe18  EFLAGS: 00010246
 RAX: 0000000000000003 RBX: ffffffffa03b5200 RCX: 0000000000000000
 RDX: 0000000000001000 RSI: ffff88080fa7fe38 RDI: ffffffffa03b5000
 RBP: ffff88080fa7fe28 R08: 0000000000000010 R09: 0000000000000000
 R10: 0000000000000000 R11: 000000000000000f R12: ffffffffa03b5000
 R13: ffffffffa03b5008 R14: ffffffffa03b5200 R15: ffffffffa03b5000
 FS:  00007f6ae57ef740(0000) GS:ffff88101e7a0000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 CR2: 0000000000404f70 CR3: 0000000ffed48000 CR4: 00000000001407e0
 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
 Stack:
  ffffffffa03b5200 ffff8810101e4800 ffff88080fa7fe70 ffffffff810d666c
  ffff88081e807300 000000002e0f2fbf 0000000000000000 ffff88100f257b00
  ffffffffa03b5008 ffff88080fa7ff48 ffff8810101e4800 ffff88080fa7fee0
 Call Trace:
  [<ffffffff810d666c>] m_show+0x19c/0x1e0
  [<ffffffff811e4d7e>] seq_read+0x16e/0x3b0
  [<ffffffff812281ed>] proc_reg_read+0x3d/0x80
  [<ffffffff811c0f2c>] vfs_read+0x9c/0x170
  [<ffffffff811c1a58>] SyS_read+0x58/0xb0
  [<ffffffff81605829>] system_call_fastpath+0x16/0x1b
 Code: 48 63 c2 83 c2 01 c6 04 03 29 48 63 d2 eb d9 0f 1f 80 00 00 00 00 48 63 d2 c6 04 13 2d 41 8b 0c 24 8d 50 02 83 f9 01 75 b2 eb cb <0f> 0b 66 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 55 48 89 e5 41
 RIP  [<ffffffff810d64c5>] module_flags+0xb5/0xc0
  RSP <ffff88080fa7fe18>

    Consider the two processes running on the system.

    CPU 0 (/proc/modules reader)
    CPU 1 (loading/unloading module)

    CPU 0 opens /proc/modules, and starts displaying data for each module by
    traversing the modules list via fs/seq_file.c:seq_open() and
    fs/seq_file.c:seq_read().  For each module in the modules list, seq_read
    does

            op->start()  <-- this is a pointer to m_start()
            op->show()   <- this is a pointer to m_show()
            op->stop()   <-- this is a pointer to m_stop()

    The m_start(), m_show(), and m_stop() module functions are defined in
    kernel/module.c. The m_start() and m_stop() functions acquire and release
    the module_mutex respectively.

    ie) When reading /proc/modules, the module_mutex is acquired and released
    for each module.

    m_show() is called with the module_mutex held.  It accesses the module
    struct data and attempts to write out module data.  It is in this code
    path that the above BUG_ON() warning is encountered, specifically m_show()
    calls

    static char *module_flags(struct module *mod, char *buf)
    {
            int bx = 0;

            BUG_ON(mod->state == MODULE_STATE_UNFORMED);
    ...

    The other thread, CPU 1, in unloading the module calls the syscall
    delete_module() defined in kernel/module.c.  The module_mutex is acquired
    for a short time, and then released.  free_module() is called without the
    module_mutex.  free_module() then sets mod->state = MODULE_STATE_UNFORMED,
    also without the module_mutex.  Some additional code is called and then the
    module_mutex is reacquired to remove the module from the modules list:

        /* Now we can delete it from the lists */
        mutex_lock(&module_mutex);
        stop_machine(__unlink_module, mod, NULL);
        mutex_unlock(&module_mutex);

This is the sequence of events that leads to the panic.

CPU 1 is removing dummy_module via delete_module().  It acquires the
module_mutex, and then releases it.  CPU 1 has NOT set dummy_module->state to
MODULE_STATE_UNFORMED yet.

CPU 0, which is reading the /proc/modules, acquires the module_mutex and
acquires a pointer to the dummy_module which is still in the modules list.
CPU 0 calls m_show for dummy_module.  The check in m_show() for
MODULE_STATE_UNFORMED passed for dummy_module even though it is being
torn down.

Meanwhile CPU 1, which has been continuing to remove dummy_module without
holding the module_mutex, now calls free_module() and sets
dummy_module->state to MODULE_STATE_UNFORMED.

CPU 0 now calls module_flags() with dummy_module and ...

static char *module_flags(struct module *mod, char *buf)
{
        int bx = 0;

        BUG_ON(mod->state == MODULE_STATE_UNFORMED);

and BOOM.

Acquire and release the module_mutex lock around the setting of
MODULE_STATE_UNFORMED in the teardown path, which should resolve the
problem.

Testing: In the unpatched kernel I can panic the system within 1 minute by
doing

while (true) do insmod dummy_module.ko; rmmod dummy_module.ko; done

and

while (true) do cat /proc/modules; done

in separate terminals.

In the patched kernel I was able to run just over one hour without seeing
any issues.  I also verified the output of panic via sysrq-c and the output
of /proc/modules looks correct for all three states for the dummy_module.

        dummy_module 12661 0 - Unloading 0xffffffffa03a5000 (OE-)
        dummy_module 12661 0 - Live 0xffffffffa03bb000 (OE)
        dummy_module 14015 1 - Loading 0xffffffffa03a5000 (OE+)

Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
7 years agomnt: Prevent pivot_root from creating a loop in the mount tree
Eric W. Biederman [Wed, 8 Oct 2014 17:42:27 +0000 (10:42 -0700)]
mnt: Prevent pivot_root from creating a loop in the mount tree

Andy Lutomirski recently demonstrated that when chroot is used to set
the root path below the path for the new ``root'' passed to pivot_root
the pivot_root system call succeeds and leaks mounts.

In examining the code I see that starting with a new root that is
below the current root in the mount tree will result in a loop in the
mount tree after the mounts are detached and then reattached to one
another.  Resulting in all kinds of ugliness including a leak of that
mounts involved in the leak of the mount loop.

Prevent this problem by ensuring that the new mount is reachable from
the current root of the mount tree.

[Added stable cc.  Fixes CVE-2014-7970.  --Andy]

Cc: stable@vger.kernel.org
Reported-by: Andy Lutomirski <luto@amacapital.net>
Reviewed-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/87bnpmihks.fsf@x220.int.ebiederm.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
7 years agotcp: TCP Small Queues and strange attractors
Eric Dumazet [Mon, 13 Oct 2014 13:27:47 +0000 (06:27 -0700)]
tcp: TCP Small Queues and strange attractors

TCP Small queues tries to keep number of packets in qdisc
as small as possible, and depends on a tasklet to feed following
packets at TX completion time.
Choice of tasklet was driven by latencies requirements.

Then, TCP stack tries to avoid reorders, by locking flows with
outstanding packets in qdisc in a given TX queue.

What can happen is that many flows get attracted by a low performing
TX queue, and cpu servicing TX completion has to feed packets for all of
them, making this cpu 100% busy in softirq mode.

This became particularly visible with latest skb->xmit_more support

Strategy adopted in this patch is to detect when tcp_wfree() is called
from ksoftirqd and let the outstanding queue for this flow being drained
before feeding additional packets, so that skb->ooo_okay can be set
to allow select_queue() to select the optimal queue :

Incoming ACKS are normally handled by different cpus, so this patch
gives more chance for these cpus to take over the burden of feeding
qdisc with future packets.

Tested:

lpaa23:~# ./super_netperf 1400 --google-pacing-rate 3028000 -H lpaa24 -l 3600 &

lpaa23:~# sar -n DEV 1 10 | grep eth1
06:16:18 AM      eth1 595448.00 1190564.00  38381.09 1760253.12      0.00      0.00      1.00
06:16:19 AM      eth1 594858.00 1189686.00  38340.76 1758952.72      0.00      0.00      0.00
06:16:20 AM      eth1 597017.00 1194019.00  38480.79 1765370.29      0.00      0.00      1.00
06:16:21 AM      eth1 595450.00 1190936.00  38380.19 1760805.05      0.00      0.00      0.00
06:16:22 AM      eth1 596385.00 1193096.00  38442.56 1763976.29      0.00      0.00      1.00
06:16:23 AM      eth1 598155.00 1195978.00  38552.97 1768264.60      0.00      0.00      0.00
06:16:24 AM      eth1 594405.00 1188643.00  38312.57 1757414.89      0.00      0.00      1.00
06:16:25 AM      eth1 593366.00 1187154.00  38252.16 1755195.83      0.00      0.00      0.00
06:16:26 AM      eth1 593188.00 1186118.00  38232.88 1753682.57      0.00      0.00      1.00
06:16:27 AM      eth1 596301.00 1192241.00  38440.94 1762733.09      0.00      0.00      0.00
Average:         eth1 595457.30 1190843.50  38381.69 1760664.84      0.00      0.00      0.50
lpaa23:~# ./tc -s -d qd sh dev eth1 | grep backlog
 backlog 7606336b 2513p requeues 167982
 backlog 224072b 74p requeues 566
 backlog 581376b 192p requeues 5598
 backlog 181680b 60p requeues 1070
 backlog 5305056b 1753p requeues 110166    // Here, this TX queue is attracting flows
 backlog 157456b 52p requeues 1758
 backlog 672216b 222p requeues 3025
 backlog 60560b 20p requeues 24541
 backlog 448144b 148p requeues 21258

lpaa23:~# echo 1 >/proc/sys/net/ipv4/tcp_tsq_enable_tcp_wfree_ksoftirqd_detect

Immediate jump to full bandwidth, and traffic is properly
shard on all tx queues.

lpaa23:~# sar -n DEV 1 10 | grep eth1
06:16:46 AM      eth1 1397632.00 2795397.00  90081.87 4133031.26      0.00      0.00      1.00
06:16:47 AM      eth1 1396874.00 2793614.00  90032.99 4130385.46      0.00      0.00      0.00
06:16:48 AM      eth1 1395842.00 2791600.00  89966.46 4127409.67      0.00      0.00      1.00
06:16:49 AM      eth1 1395528.00 2791017.00  89946.17 4126551.24      0.00      0.00      0.00
06:16:50 AM      eth1 1397891.00 2795716.00  90098.74 4133497.39      0.00      0.00      1.00
06:16:51 AM      eth1 1394951.00 2789984.00  89908.96 4125022.51      0.00      0.00      0.00
06:16:52 AM      eth1 1394608.00 2789190.00  89886.90 4123851.36      0.00      0.00      1.00
06:16:53 AM      eth1 1395314.00 2790653.00  89934.33 4125983.09      0.00      0.00      0.00
06:16:54 AM      eth1 1396115.00 2792276.00  89984.25 4128411.21      0.00      0.00      1.00
06:16:55 AM      eth1 1396829.00 2793523.00  90030.19 4130250.28      0.00      0.00      0.00
Average:         eth1 1396158.40 2792297.00  89987.09 4128439.35      0.00      0.00      0.50

lpaa23:~# tc -s -d qd sh dev eth1 | grep backlog
 backlog 7900052b 2609p requeues 173287
 backlog 878120b 290p requeues 589
 backlog 1068884b 354p requeues 5621
 backlog 996212b 329p requeues 1088
 backlog 984100b 325p requeues 115316
 backlog 956848b 316p requeues 1781
 backlog 1080996b 357p requeues 3047
 backlog 975016b 322p requeues 24571
 backlog 990156b 327p requeues 21274

(All 8 TX queues get a fair share of the traffic)

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoMerge branch 'qlcnic'
David S. Miller [Tue, 14 Oct 2014 21:05:23 +0000 (17:05 -0400)]
Merge branch 'qlcnic'

Rajesh Borundia says:

====================
qlcnic: Bug fixes

This series fixes following issues.

* We were programming maximum number of arguments supported by
  adapter instead of required in a command.
* Destroy tx command requires three arguments instead of two.

Please apply these patches to net.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoqlcnic: Fix number of arguments in destroy tx context command
Rajesh Borundia [Tue, 14 Oct 2014 11:41:46 +0000 (07:41 -0400)]
qlcnic: Fix number of arguments in destroy tx context command

o Number of arguments taken by destroy tx command is three
  instead of two.

Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoqlcnic: Fix programming number of arguments in a command.
Rajesh Borundia [Tue, 14 Oct 2014 11:41:45 +0000 (07:41 -0400)]
qlcnic: Fix programming number of arguments in a command.

o Initially we were programming maximum number of arguments.
  Instead we should program number of arguments required in
  a command.
o Maximum number of arguments for 82xx adapter is four. Fix it
  for GET_ESWITCH_STATS command.

Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agogenl_magic: Resolve logical-op warnings
Mark Rustad [Tue, 14 Oct 2014 13:28:38 +0000 (06:28 -0700)]
genl_magic: Resolve logical-op warnings

Resolve "logical 'and' applied to non-boolean constant" warnings"
that appear in W=2 builds by adding !! to a bit test.

Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agonet: Trap attempts to call sock_kfree_s() with a NULL pointer.
David S. Miller [Tue, 14 Oct 2014 21:02:37 +0000 (17:02 -0400)]
net: Trap attempts to call sock_kfree_s() with a NULL pointer.

Unlike normal kfree() it is never right to call sock_kfree_s() with
a NULL pointer, because sock_kfree_s() also has the side effect of
discharging the memory from the sockets quota.

Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agords: avoid calling sock_kfree_s() on allocation failure
Cong Wang [Tue, 14 Oct 2014 19:35:08 +0000 (12:35 -0700)]
rds: avoid calling sock_kfree_s() on allocation failure

It is okay to free a NULL pointer but not okay to mischarge the socket optmem
accounting. Compile test only.

Reported-by: rucsoftsec@gmail.com
Cc: Chien Yen <chien.yen@oracle.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agocxgb4: Fix FW flash logic using ethtool
Hariprasad Shenai [Tue, 14 Oct 2014 20:24:14 +0000 (01:54 +0530)]
cxgb4: Fix FW flash logic using ethtool

Use t4_fw_upgrade instead of t4_load_fw to write firmware into FLASH, since
t4_load_fw doesn't co-ordinate with the firmware and the adapter can get hosed
enough to require a power cycle of the system.

Based on original work by Casey Leedom <leedom@chelsio.com>

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoMerge branch 'stmmac'
David S. Miller [Tue, 14 Oct 2014 20:40:49 +0000 (16:40 -0400)]
Merge branch 'stmmac'

Giuseppe Cavallaro says:

====================
stmmac: review and fix the dwmac-sti glue-logic

This patch is to review the whole glue logic adopted on STi SoCs that
was bugged.
In the old glue-logic there was a lot of confusion when setup the
retiming especially for STiD127 where, for example, the bits 6 and 7
(in the GMAC  control register) have a different meaning of what is
used for STiH4xx SoCs. So we cannot adopt the same glue for all these
SoCs.
Moreover, GiGa on STiD127 didn't work and, for all the SoCs, the RGMII
couldn't run when the speed was 10Mbps (because the clock was not properly
managed).
Note that the phy clock needs to be provided by the platform as well as
documented in the related binding file (updated as consequence).

The old code supported too many configurations never adopted and validated.
This made the code very complex to maintain and debug in case of issues.

The patch simplifies all the configurations as commented in the tables
inside the file and obviously it has been tested on all the boards
based on the SoCs mentioned.

With this patch, the dwmac-sti is also ready to support new configurations that
will be available on next SoC generations.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agostmmac: dwmac-sti: review the glue-logic for STi4xx and STiD127 SoCs
Giuseppe CAVALLARO [Tue, 14 Oct 2014 06:12:56 +0000 (08:12 +0200)]
stmmac: dwmac-sti: review the glue-logic for STi4xx and STiD127 SoCs

This patch is to review the whole glue logic adopted on STi SoCs that
was bugged.

In the old glue-logic there was a lot of confusion when setup the
retiming especially for STiD127 where, for example, the bits 6 and 7
(in the GMAC  control register) have a different meaning of what is
used for STiH4xx SoCs. So we cannot adopt the same glue for all these
SoCs.
Moreover, GiGa on STiD127 didn't work and, for all the SoCs, the RGMII
couldn't run when the speed was 10Mbps (because the clock was not properly
managed).
Note that the phy clock needs to be provided by the platform as well as
documented in the related binding file (updated as consequence).

The old code supported too many configurations never adopted and validated.
This made the code very complex to maintain and debug in case of issues.

The patch simplifies all the configurations as commented in the tables
inside the file and obviously it has been tested on all the boards
based on the SoCs mentioned.

With this patch, the dwmac-sti is also ready to support new configurations that
will be available on next SoC generations.

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agostmmac: make the STi Layer compatible to STiH407
Giuseppe CAVALLARO [Tue, 14 Oct 2014 06:12:55 +0000 (08:12 +0200)]
stmmac: make the STi Layer compatible to STiH407

This adds the missing compatibility to the STiH407 SoC.

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agostmmac: platform: fix FIXED_PHY support.
Giuseppe CAVALLARO [Tue, 14 Oct 2014 06:11:54 +0000 (08:11 +0200)]
stmmac: platform: fix FIXED_PHY support.

On several STi platforms: e.g. stihxxx-b2120 an Ethernet switch is
embedded and connected to the stmmac via RGMII mode. So this is managed
by using the FIXED_PHY. In that case, the support in the platform needs
to be fixed to allow the stmmac to dialog with the switch via fixed-link
by using phy_bus_name property.

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agodsa: mv88e6171: Fix tag_protocol check
Guenter Roeck [Tue, 14 Oct 2014 18:21:04 +0000 (11:21 -0700)]
dsa: mv88e6171: Fix tag_protocol check

tag_protocol is now an enum, so drivers have to check against it.

Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoMerge branch 'xgene'
David S. Miller [Tue, 14 Oct 2014 20:09:38 +0000 (16:09 -0400)]
Merge branch 'xgene'

Iyappan Subramanian says:

====================
Adding SGMII based 1GbE basic support to APM X-Gene SoC ethernet driver.

v2: Address comments from v1
* Split the patchset into two, the first one being preparatory patch
* Added link_state function pointer to the xgene_mac_ops structure
* Added xgene_indirect_ctl structure for indirect read/write arguments

v1:
* Initial version
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agodrivers: net: xgene: Add SGMII based 1GbE ethtool support
Iyappan Subramanian [Tue, 14 Oct 2014 00:05:35 +0000 (17:05 -0700)]
drivers: net: xgene: Add SGMII based 1GbE ethtool support

Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agodrivers: net: xgene: Add SGMII based 1GbE support
Iyappan Subramanian [Tue, 14 Oct 2014 00:05:34 +0000 (17:05 -0700)]
drivers: net: xgene: Add SGMII based 1GbE support

Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agodrivers: net: xgene: Preparing for adding SGMII based 1GbE
Iyappan Subramanian [Tue, 14 Oct 2014 00:05:33 +0000 (17:05 -0700)]
drivers: net: xgene: Preparing for adding SGMII based 1GbE

- Added link_state function pointer to the xgene__mac_ops structure
- Moved ring manager (pdata->rm) assignment to xgene_enet_setup_ops
- Removed unused variable (pdata->phy_addr) and macro (FULL_DUPLEX)

Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agodtb: Add SGMII based 1GbE node to APM X-Gene SoC device tree
Iyappan Subramanian [Tue, 14 Oct 2014 00:05:32 +0000 (17:05 -0700)]
dtb: Add SGMII based 1GbE node to APM X-Gene SoC device tree

Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agonet: filter: move common defines into bpf_common.h
Alexei Starovoitov [Tue, 14 Oct 2014 09:08:54 +0000 (02:08 -0700)]
net: filter: move common defines into bpf_common.h

userspace programs that use eBPF instruction macros need to include two files:
uapi/linux/filter.h and uapi/linux/bpf.h
Move common macro definitions that are shared between classic BPF and eBPF
into uapi/linux/bpf_common.h, so that user app can include only one bpf.h file

Cc: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agocaif_usb: use target structure member in memset
Fabian Frederick [Tue, 14 Oct 2014 17:01:14 +0000 (19:01 +0200)]
caif_usb: use target structure member in memset

parent cfusbl was used instead of first structure member 'layer'

Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agocaif_usb: remove redundant memory message
Fabian Frederick [Tue, 14 Oct 2014 17:00:55 +0000 (19:00 +0200)]
caif_usb: remove redundant memory message

Let MM subsystem display out of memory messages.

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agocaif: replace kmalloc/memset 0 by kzalloc
Fabian Frederick [Mon, 13 Oct 2014 20:21:46 +0000 (22:21 +0200)]
caif: replace kmalloc/memset 0 by kzalloc

Also add blank line after declaration

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agodrivers: net: cpsw: remove child devices while driver detach
Mugunthan V N [Mon, 13 Oct 2014 16:51:07 +0000 (22:21 +0530)]
drivers: net: cpsw: remove child devices while driver detach

remove all the child devices from the system to make sure that re-insert of
cpsw module doesn't fail on child device populated by of_platform_populate().

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agodrivers: net: davinci_cpdma: remove spinlock as SOFTIRQ-unsafe lock order detected
Mugunthan V N [Mon, 13 Oct 2014 16:51:06 +0000 (22:21 +0530)]
drivers: net: davinci_cpdma: remove spinlock as SOFTIRQ-unsafe lock order detected

remove spinlock in cpdma_desc_pool_destroy() as there is no active cpdma
channel and iounmap should be called without auquiring lock.

root@dra7xx-evm:~# modprobe -r ti_cpsw
[   50.539743]
[   50.541312] ======================================================
[   50.547796] [ INFO: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected ]
[   50.554826] 3.14.19-02124-g95c5b7b #308 Not tainted
[   50.559939] ------------------------------------------------------
[   50.566416] modprobe/1921 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire:
[   50.573347]  (vmap_area_lock){+.+...}, at: [<c01127fc>] find_vmap_area+0x10/0x6c
[   50.581132]
[   50.581132] and this task is already holding:
[   50.587249]  (&(&pool->lock)->rlock#2){..-...}, at: [<bf017c74>] cpdma_ctlr_destroy+0x5c/0x114 [davinci_cpdma]
[   50.597766] which would create a new lock dependency:
[   50.603048]  (&(&pool->lock)->rlock#2){..-...} -> (vmap_area_lock){+.+...}
[   50.610296]
[   50.610296] but this new dependency connects a SOFTIRQ-irq-safe lock:
[   50.618601]  (&(&pool->lock)->rlock#2){..-...}
... which became SOFTIRQ-irq-safe at:
[   50.626829]   [<c06585a4>] _raw_spin_lock_irqsave+0x38/0x4c
[   50.632677]   [<bf01773c>] cpdma_desc_free.constprop.7+0x28/0x58 [davinci_cpdma]
[   50.640437]   [<bf0177e8>] __cpdma_chan_free+0x7c/0xa8 [davinci_cpdma]
[   50.647289]   [<bf017908>] __cpdma_chan_process+0xf4/0x134 [davinci_cpdma]
[   50.654512]   [<bf017984>] cpdma_chan_process+0x3c/0x54 [davinci_cpdma]
[   50.661455]   [<bf0277e8>] cpsw_poll+0x14/0xa8 [ti_cpsw]
[   50.667038]   [<c05844f4>] net_rx_action+0xc0/0x1e8
[   50.672150]   [<c0048234>] __do_softirq+0xcc/0x304
[   50.677183]   [<c004873c>] irq_exit+0xa8/0xfc
[   50.681751]   [<c000eeac>] handle_IRQ+0x50/0xb0
[   50.686513]   [<c0008638>] gic_handle_irq+0x28/0x5c
[   50.691628]   [<c06590a4>] __irq_svc+0x44/0x5c
[   50.696289]   [<c0658ab4>] _raw_spin_unlock_irqrestore+0x34/0x44
[   50.702591]   [<c065a9c4>] do_page_fault.part.9+0x144/0x3c4
[   50.708433]   [<c065acb8>] do_page_fault+0x74/0x84
[   50.713453]   [<c00083dc>] do_DataAbort+0x34/0x98
[   50.718391]   [<c065923c>] __dabt_usr+0x3c/0x40
[   50.723148]
[   50.723148] to a SOFTIRQ-irq-unsafe lock:
[   50.728893]  (vmap_area_lock){+.+...}
... which became SOFTIRQ-irq-unsafe at:
[   50.736476] ...  [<c06584e8>] _raw_spin_lock+0x28/0x38
[   50.741876]   [<c011376c>] alloc_vmap_area.isra.28+0xb8/0x300
[   50.747908]   [<c0113a44>] __get_vm_area_node.isra.29+0x90/0x134
[   50.754210]   [<c011486c>] get_vm_area_caller+0x3c/0x48
[   50.759692]   [<c0114be0>] vmap+0x40/0x78
[   50.763900]   [<c09442f0>] check_writebuffer_bugs+0x54/0x1a0
[   50.769835]   [<c093eac0>] start_kernel+0x320/0x388
[   50.774952]   [<80008074>] 0x80008074
[   50.778793]
[   50.778793] other info that might help us debug this:
[   50.778793]
[   50.787181]  Possible interrupt unsafe locking scenario:
[   50.787181]
[   50.794295]        CPU0                    CPU1
[   50.799042]        ----                    ----
[   50.803785]   lock(vmap_area_lock);
[   50.807446]                                local_irq_disable();
[   50.813652]                                lock(&(&pool->lock)->rlock#2);
[   50.820782]                                lock(vmap_area_lock);
[   50.827086]   <Interrupt>
[   50.829823]     lock(&(&pool->lock)->rlock#2);
[   50.834490]
[   50.834490]  *** DEADLOCK ***
[   50.834490]
[   50.840695] 4 locks held by modprobe/1921:
[   50.844981]  #0:  (&__lockdep_no_validate__){......}, at: [<c03e53e8>] driver_detach+0x44/0xb8
[   50.854038]  #1:  (&__lockdep_no_validate__){......}, at: [<c03e53f4>] driver_detach+0x50/0xb8
[   50.863102]  #2:  (&(&ctlr->lock)->rlock){......}, at: [<bf017c34>] cpdma_ctlr_destroy+0x1c/0x114 [davinci_cpdma]
[   50.873890]  #3:  (&(&pool->lock)->rlock#2){..-...}, at: [<bf017c74>] cpdma_ctlr_destroy+0x5c/0x114 [davinci_cpdma]
[   50.884871]
the dependencies between SOFTIRQ-irq-safe lock and the holding lock:
[   50.892827] -> (&(&pool->lock)->rlock#2){..-...} ops: 167 {
[   50.898703]    IN-SOFTIRQ-W at:
[   50.901995]                     [<c06585a4>] _raw_spin_lock_irqsave+0x38/0x4c
[   50.909476]                     [<bf01773c>] cpdma_desc_free.constprop.7+0x28/0x58 [davinci_cpdma]
[   50.918878]                     [<bf0177e8>] __cpdma_chan_free+0x7c/0xa8 [davinci_cpdma]
[   50.927366]                     [<bf017908>] __cpdma_chan_process+0xf4/0x134 [davinci_cpdma]
[   50.936218]                     [<bf017984>] cpdma_chan_process+0x3c/0x54 [davinci_cpdma]
[   50.944794]                     [<bf0277e8>] cpsw_poll+0x14/0xa8 [ti_cpsw]
[   50.952009]                     [<c05844f4>] net_rx_action+0xc0/0x1e8
[   50.958765]                     [<c0048234>] __do_softirq+0xcc/0x304
[   50.965432]                     [<c004873c>] irq_exit+0xa8/0xfc
[   50.971635]                     [<c000eeac>] handle_IRQ+0x50/0xb0
[   50.978035]                     [<c0008638>] gic_handle_irq+0x28/0x5c
[   50.984788]                     [<c06590a4>] __irq_svc+0x44/0x5c
[   50.991085]                     [<c0658ab4>] _raw_spin_unlock_irqrestore+0x34/0x44
[   50.999023]                     [<c065a9c4>] do_page_fault.part.9+0x144/0x3c4
[   51.006510]                     [<c065acb8>] do_page_fault+0x74/0x84
[   51.013171]                     [<c00083dc>] do_DataAbort+0x34/0x98
[   51.019738]                     [<c065923c>] __dabt_usr+0x3c/0x40
[   51.026129]    INITIAL USE at:
[   51.029335]                    [<c06585a4>] _raw_spin_lock_irqsave+0x38/0x4c
[   51.036729]                    [<bf017d78>] cpdma_chan_submit+0x4c/0x2f0 [davinci_cpdma]
[   51.045225]                    [<bf02863c>] cpsw_ndo_open+0x378/0x6bc [ti_cpsw]
[   51.052897]                    [<c058747c>] __dev_open+0x9c/0x104
[   51.059287]                    [<c05876ec>] __dev_change_flags+0x88/0x160
[   51.066420]                    [<c05877e4>] dev_change_flags+0x18/0x48
[   51.073270]                    [<c05ed51c>] devinet_ioctl+0x61c/0x6e0
[   51.080029]                    [<c056ee54>] sock_ioctl+0x5c/0x298
[   51.086418]                    [<c01350a4>] do_vfs_ioctl+0x78/0x61c
[   51.092993]                    [<c01356ac>] SyS_ioctl+0x64/0x74
[   51.099200]                    [<c000e580>] ret_fast_syscall+0x0/0x48
[   51.105956]  }
[   51.107696]  ... key      at: [<bf019000>] __key.21312+0x0/0xfffff650 [davinci_cpdma]
[   51.115912]  ... acquired at:
[   51.119019]    [<c00899ac>] lock_acquire+0x9c/0x104
[   51.124138]    [<c06584e8>] _raw_spin_lock+0x28/0x38
[   51.129341]    [<c01127fc>] find_vmap_area+0x10/0x6c
[   51.134547]    [<c0114960>] remove_vm_area+0x8/0x6c
[   51.139659]    [<c0114a7c>] __vunmap+0x20/0xf8
[   51.144318]    [<c001c350>] __arm_iounmap+0x10/0x18
[   51.149440]    [<bf017d08>] cpdma_ctlr_destroy+0xf0/0x114 [davinci_cpdma]
[   51.156560]    [<bf026294>] cpsw_remove+0x48/0x8c [ti_cpsw]
[   51.162407]    [<c03e62c8>] platform_drv_remove+0x18/0x1c
[   51.168063]    [<c03e4c44>] __device_release_driver+0x70/0xc8
[   51.174094]    [<c03e5458>] driver_detach+0xb4/0xb8
[   51.179212]    [<c03e4a6c>] bus_remove_driver+0x4c/0x90
[   51.184693]    [<c00b024c>] SyS_delete_module+0x10c/0x198
[   51.190355]    [<c000e580>] ret_fast_syscall+0x0/0x48
[   51.195661]
[   51.197217]
the dependencies between the lock to be acquired and SOFTIRQ-irq-unsafe lock:
[   51.205986] -> (vmap_area_lock){+.+...} ops: 520 {
[   51.211032]    HARDIRQ-ON-W at:
[   51.214321]                     [<c06584e8>] _raw_spin_lock+0x28/0x38
[   51.221090]                     [<c011376c>] alloc_vmap_area.isra.28+0xb8/0x300
[   51.228750]                     [<c0113a44>] __get_vm_area_node.isra.29+0x90/0x134
[   51.236690]                     [<c011486c>] get_vm_area_caller+0x3c/0x48
[   51.243811]                     [<c0114be0>] vmap+0x40/0x78
[   51.249654]                     [<c09442f0>] check_writebuffer_bugs+0x54/0x1a0
[   51.257239]                     [<c093eac0>] start_kernel+0x320/0x388
[   51.263994]                     [<80008074>] 0x80008074
[   51.269474]    SOFTIRQ-ON-W at:
[   51.272769]                     [<c06584e8>] _raw_spin_lock+0x28/0x38
[   51.279525]                     [<c011376c>] alloc_vmap_area.isra.28+0xb8/0x300
[   51.287190]                     [<c0113a44>] __get_vm_area_node.isra.29+0x90/0x134
[   51.295126]                     [<c011486c>] get_vm_area_caller+0x3c/0x48
[   51.302245]                     [<c0114be0>] vmap+0x40/0x78
[   51.308094]                     [<c09442f0>] check_writebuffer_bugs+0x54/0x1a0
[   51.315669]                     [<c093eac0>] start_kernel+0x320/0x388
[   51.322423]                     [<80008074>] 0x80008074
[   51.327906]    INITIAL USE at:
[   51.331112]                    [<c06584e8>] _raw_spin_lock+0x28/0x38
[   51.337775]                    [<c011376c>] alloc_vmap_area.isra.28+0xb8/0x300
[   51.345352]                    [<c0113a44>] __get_vm_area_node.isra.29+0x90/0x134
[   51.353197]                    [<c011486c>] get_vm_area_caller+0x3c/0x48
[   51.360224]                    [<c0114be0>] vmap+0x40/0x78
[   51.365977]                    [<c09442f0>] check_writebuffer_bugs+0x54/0x1a0
[   51.373464]                    [<c093eac0>] start_kernel+0x320/0x388
[   51.380131]                    [<80008074>] 0x80008074
[   51.385517]  }
[   51.387260]  ... key      at: [<c0a66948>] vmap_area_lock+0x10/0x20
[   51.393841]  ... acquired at:
[   51.396945]    [<c00899ac>] lock_acquire+0x9c/0x104
[   51.402060]    [<c06584e8>] _raw_spin_lock+0x28/0x38
[   51.407266]    [<c01127fc>] find_vmap_area+0x10/0x6c
[   51.412478]    [<c0114960>] remove_vm_area+0x8/0x6c
[   51.417592]    [<c0114a7c>] __vunmap+0x20/0xf8
[   51.422252]    [<c001c350>] __arm_iounmap+0x10/0x18
[   51.427369]    [<bf017d08>] cpdma_ctlr_destroy+0xf0/0x114 [davinci_cpdma]
[   51.434487]    [<bf026294>] cpsw_remove+0x48/0x8c [ti_cpsw]
[   51.440336]    [<c03e62c8>] platform_drv_remove+0x18/0x1c
[   51.446000]    [<c03e4c44>] __device_release_driver+0x70/0xc8
[   51.452031]    [<c03e5458>] driver_detach+0xb4/0xb8
[   51.457147]    [<c03e4a6c>] bus_remove_driver+0x4c/0x90
[   51.462628]    [<c00b024c>] SyS_delete_module+0x10c/0x198
[   51.468289]    [<c000e580>] ret_fast_syscall+0x0/0x48
[   51.473584]
[   51.475140]
[   51.475140] stack backtrace:
[   51.479703] CPU: 0 PID: 1921 Comm: modprobe Not tainted 3.14.19-02124-g95c5b7b #308
[   51.487744] [<c0016090>] (unwind_backtrace) from [<c0012060>] (show_stack+0x10/0x14)
[   51.495865] [<c0012060>] (show_stack) from [<c0652a20>] (dump_stack+0x78/0x94)
[   51.503444] [<c0652a20>] (dump_stack) from [<c0086f18>] (check_usage+0x408/0x594)
[   51.511293] [<c0086f18>] (check_usage) from [<c00870f8>] (check_irq_usage+0x54/0xb0)
[   51.519416] [<c00870f8>] (check_irq_usage) from [<c0088724>] (__lock_acquire+0xe54/0x1b90)
[   51.528077] [<c0088724>] (__lock_acquire) from [<c00899ac>] (lock_acquire+0x9c/0x104)
[   51.536291] [<c00899ac>] (lock_acquire) from [<c06584e8>] (_raw_spin_lock+0x28/0x38)
[   51.544417] [<c06584e8>] (_raw_spin_lock) from [<c01127fc>] (find_vmap_area+0x10/0x6c)
[   51.552726] [<c01127fc>] (find_vmap_area) from [<c0114960>] (remove_vm_area+0x8/0x6c)
[   51.560935] [<c0114960>] (remove_vm_area) from [<c0114a7c>] (__vunmap+0x20/0xf8)
[   51.568693] [<c0114a7c>] (__vunmap) from [<c001c350>] (__arm_iounmap+0x10/0x18)
[   51.576362] [<c001c350>] (__arm_iounmap) from [<bf017d08>] (cpdma_ctlr_destroy+0xf0/0x114 [davinci_cpdma])
[   51.586494] [<bf017d08>] (cpdma_ctlr_destroy [davinci_cpdma]) from [<bf026294>] (cpsw_remove+0x48/0x8c [ti_cpsw])
[   51.597261] [<bf026294>] (cpsw_remove [ti_cpsw]) from [<c03e62c8>] (platform_drv_remove+0x18/0x1c)
[   51.606659] [<c03e62c8>] (platform_drv_remove) from [<c03e4c44>] (__device_release_driver+0x70/0xc8)
[   51.616237] [<c03e4c44>] (__device_release_driver) from [<c03e5458>] (driver_detach+0xb4/0xb8)
[   51.625264] [<c03e5458>] (driver_detach) from [<c03e4a6c>] (bus_remove_driver+0x4c/0x90)
[   51.633749] [<c03e4a6c>] (bus_remove_driver) from [<c00b024c>] (SyS_delete_module+0x10c/0x198)
[   51.642781] [<c00b024c>] (SyS_delete_module) from [<c000e580>] (ret_fast_syscall+0x0/0x48)

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agodrivers: net: davinci_cpdma: remove kfree on objects allocated with devm_* apis
Mugunthan V N [Mon, 13 Oct 2014 16:51:05 +0000 (22:21 +0530)]
drivers: net: davinci_cpdma: remove kfree on objects allocated with devm_* apis

memories allocated with devm_* apis must not be freed with kfree apis,
so removing the kfree calls

Fixes: e194312854ed ('drivers: net: davinci_cpdma: Convert kzalloc() to devm_kzalloc().')

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agotg3: Add skb->xmit_more support
Prashant Sreedharan [Mon, 13 Oct 2014 16:21:42 +0000 (09:21 -0700)]
tg3: Add skb->xmit_more support

Ring TX doorbell only if xmit_more is not set or the queue is stopped.

Suggested-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoipv4: fix nexthop attlen check in fib_nh_match
Jiri Pirko [Mon, 13 Oct 2014 14:34:10 +0000 (16:34 +0200)]
ipv4: fix nexthop attlen check in fib_nh_match

fib_nh_match does not match nexthops correctly. Example:

ip route add 172.16.10/24 nexthop via 192.168.122.12 dev eth0 \
                          nexthop via 192.168.122.13 dev eth0
ip route del 172.16.10/24 nexthop via 192.168.122.14 dev eth0 \
                          nexthop via 192.168.122.15 dev eth0

Del command is successful and route is removed. After this patch
applied, the route is correctly matched and result is:
RTNETLINK answers: No such process

Please consider this for stable trees as well.

Fixes: 4e902c57417c4 ("[IPv4]: FIB configuration using struct fib_config")
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agotcp: fix tcp_ack() performance problem
Eric Dumazet [Sat, 11 Oct 2014 22:17:29 +0000 (15:17 -0700)]
tcp: fix tcp_ack() performance problem

We worked hard to improve tcp_ack() performance, by not accessing
skb_shinfo() in fast path (cd7d8498c9a5 tcp: change tcp_skb_pcount()
location)

We still have one spurious access because of ACK timestamping,
added in commit e1c8a607b281 ("net-timestamp: ACK timestamp for
bytestreams")

By checking if sk_tsflags has SOF_TIMESTAMPING_TX_ACK set,
we can avoid two cache line misses for the common case.

While we are at it, add two prefetchw() :

One in tcp_ack() to bring skb at the head of write queue.

One in tcp_clean_rtx_queue() loop to bring following skb,
as we will delete skb from the write queue and dirty skb->next->prev.

Add a couple of [un]likely() clauses.

After this patch, tcp_ack() is no longer the most consuming
function in tcp stack.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Van Jacobson <vanj@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoceph: fix divide-by-zero in __validate_layout()
Yan, Zheng [Tue, 14 Oct 2014 07:38:01 +0000 (15:38 +0800)]
ceph: fix divide-by-zero in __validate_layout()

The 'stripe_unit' field is 64 bits, casting it to 32 bits can result zero.

Signed-off-by: Yan, Zheng <zyan@redhat.com>
7 years agorbd: rbd workqueues need a resque worker
Ilya Dryomov [Fri, 10 Oct 2014 14:36:07 +0000 (18:36 +0400)]
rbd: rbd workqueues need a resque worker

Need to use WQ_MEM_RECLAIM for our workqueues to prevent I/O lockups
under memory pressure - we sit on the memory reclaim path.

Cc: stable@vger.kernel.org # 3.17, needs backporting for 3.16
Signed-off-by: Ilya Dryomov <idryomov@redhat.com>
Tested-by: Micha Krause <micha@krausam.de>
Reviewed-by: Sage Weil <sage@redhat.com>
7 years agolibceph: ceph-msgr workqueue needs a resque worker
Ilya Dryomov [Fri, 10 Oct 2014 12:39:05 +0000 (16:39 +0400)]
libceph: ceph-msgr workqueue needs a resque worker

Commit f363e45fd118 ("net/ceph: make ceph_msgr_wq non-reentrant")
effectively removed WQ_MEM_RECLAIM flag from ceph_msgr_wq.  This is
wrong - libceph is very much a memory reclaim path, so restore it.

Cc: stable@vger.kernel.org # needs backporting for < 3.12
Signed-off-by: Ilya Dryomov <idryomov@redhat.com>
Tested-by: Micha Krause <micha@krausam.de>
Reviewed-by: Sage Weil <sage@redhat.com>
7 years agoceph: fix bool assignments
Fabian Frederick [Thu, 9 Oct 2014 21:16:35 +0000 (23:16 +0200)]
ceph: fix bool assignments

Fix some coccinelle warnings:
fs/ceph/caps.c:2400:6-10: WARNING: Assignment of bool to 0/1
fs/ceph/caps.c:2401:6-15: WARNING: Assignment of bool to 0/1
fs/ceph/caps.c:2402:6-17: WARNING: Assignment of bool to 0/1
fs/ceph/caps.c:2403:6-22: WARNING: Assignment of bool to 0/1
fs/ceph/caps.c:2404:6-22: WARNING: Assignment of bool to 0/1
fs/ceph/caps.c:2405:6-19: WARNING: Assignment of bool to 0/1
fs/ceph/caps.c:2440:4-20: WARNING: Assignment of bool to 0/1
fs/ceph/caps.c:2469:3-16: WARNING: Assignment of bool to 0/1
fs/ceph/caps.c:2490:2-18: WARNING: Assignment of bool to 0/1
fs/ceph/caps.c:2519:3-7: WARNING: Assignment of bool to 0/1
fs/ceph/caps.c:2549:3-12: WARNING: Assignment of bool to 0/1
fs/ceph/caps.c:2575:2-6: WARNING: Assignment of bool to 0/1
fs/ceph/caps.c:2589:3-7: WARNING: Assignment of bool to 0/1

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Ilya Dryomov <idryomov@redhat.com>
7 years agolibceph: separate multiple ops with commas in debugfs output
Ilya Dryomov [Mon, 6 Oct 2014 14:40:27 +0000 (18:40 +0400)]
libceph: separate multiple ops with commas in debugfs output

For requests with multiple ops, separate ops with commas instead of \t,
which is a field separator here.

Signed-off-by: Ilya Dryomov <idryomov@redhat.com>
Reviewed-by: Sage Weil <sage@redhat.com>
7 years agolibceph: sync osd op definitions in rados.h
Ilya Dryomov [Thu, 2 Oct 2014 13:22:29 +0000 (17:22 +0400)]
libceph: sync osd op definitions in rados.h

Bring in missing osd ops and strings, use macros to eliminate multiple
points of maintenance.

Signed-off-by: Ilya Dryomov <idryomov@redhat.com>
Reviewed-by: Sage Weil <sage@redhat.com>
7 years agolibceph: remove redundant declaration
Fabian Frederick [Tue, 30 Sep 2014 20:07:50 +0000 (22:07 +0200)]
libceph: remove redundant declaration

ceph_release_page_vector was defined twice in libceph.h

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Ilya Dryomov <idryomov@redhat.com>
7 years agoceph: additional debugfs output
John Spray [Fri, 12 Sep 2014 15:58:49 +0000 (16:58 +0100)]
ceph: additional debugfs output

MDS session state and client global ID is
useful instrumentation when testing.

Signed-off-by: John Spray <john.spray@redhat.com>
7 years agoceph: export ceph_session_state_name function
John Spray [Fri, 19 Sep 2014 12:51:08 +0000 (13:51 +0100)]
ceph: export ceph_session_state_name function

...so that it can be used from the ceph debugfs
code when dumping session info.

Signed-off-by: John Spray <john.spray@redhat.com>
7 years agoceph: include the initial ACL in create/mkdir/mknod MDS requests
Yan, Zheng [Tue, 16 Sep 2014 12:35:17 +0000 (20:35 +0800)]
ceph: include the initial ACL in create/mkdir/mknod MDS requests

Current code set new file/directory's initial ACL in a non-atomic
manner.
Client first sends request to MDS to create new file/directory, then set
the initial ACL after the new file/directory is successfully created.

The fix is include the initial ACL in create/mkdir/mknod MDS requests.
So MDS can handle creating file/directory and setting the initial ACL in
one request.

Signed-off-by: Yan, Zheng <zyan@redhat.com>
Reviewed-by: Sage Weil <sage@redhat.com>
7 years agoceph: use pagelist to present MDS request data
Yan, Zheng [Tue, 16 Sep 2014 11:15:28 +0000 (19:15 +0800)]
ceph: use pagelist to present MDS request data

Current code uses page array to present MDS request data. Pages in the
array are allocated/freed by caller of ceph_mdsc_do_request(). If request
is interrupted, the pages can be freed while they are still being used by
the request message.

The fix is use pagelist to present MDS request data. Pagelist is
reference counted.

Signed-off-by: Yan, Zheng <zyan@redhat.com>
Reviewed-by: Sage Weil <sage@redhat.com>
7 years agolibceph: reference counting pagelist
Yan, Zheng [Tue, 16 Sep 2014 09:50:45 +0000 (17:50 +0800)]
libceph: reference counting pagelist

this allow pagelist to present data that may be sent multiple times.

Signed-off-by: Yan, Zheng <zyan@redhat.com>
Reviewed-by: Sage Weil <sage@redhat.com>