rt2x00: Data and desc pointer initialization

rt2500usb and rt73usb data and desc pointer initialization
was incorrect because it was using uninitialized variables
to determine the length.

In addition rt2500usb used skb_pull and removed the ieee80211
from each received frame instead of using skb_trim to remove
the device descriptor from the frame.

Finally this also fixes the descriptor override when 4 byte
aligning occured. We still need a completely valid descriptor
when using the TX/RX dumping capabilities in debugfs.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: Add N-PHY related initvals firmware filenames.

This adds the initval filenames for the N-PHY firmware.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: Fix tim search buffer overrun

Use the length of the variable section of the beacon instead of the
whole beacon length for bounds checking.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: Put multicast frames on the mcast queue

This queues frames flagged as "send after DTIM" by mac80211
on the special multicast queue. The firmware will take care
to send the packet after the DTIM.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: Fix template upload locking.

This fixes the template upload locking.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: Fix upload of beacon packets to the hardware

This fixes uploading of the beacon data and writing of the
TIM and DTIM offsets.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: add unified BSS configuration

This patch (based on Ron Rindjunsky's) creates a framework for
a unified way to pass BSS configuration to drivers that require
the information, e.g. for implementing power save mode.

This patch introduces new ieee80211_bss_conf structure that is
passed to the driver via the new bss_info_changed() callback
when the BSS configuration changes.

This new BSS configuration infrastructure adds the following
new features:
 * drivers are notified of their association AID
 * drivers are notified of association status

and replaces the erp_ie_changed() callback. The patch also does
the relevant driver updates for the latter change.

Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Fix rate reporting regression

Mattias Nissler's "clean up rate selection" patch incorrectly changes
the behavior of txrate setting in sta_info. This patch backs out parts
of the rate selection consolidation in order to fix this issue for now.

Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: A-MPDU Rx flow enabled

This patch enables the A-MPDU Rx flow. it contains several
adjustments to new mac80211 A-MPDU Rx flow.

Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Fix frame duration oops

This patch fixes an oops which was introduced as a regression by
commit fd640775bd16e1df50c867cc547af0, on the patch titled,
"mac80211: dont use interface indices in drivers".

ieee80211_generic_frame_duration() now relies on sdata->flags which
itself gets set upon bringing the interface up. We check for the
virtual interface now before setting the rate duration registers.

After the mode changes are introduced onto mac80211 we should revisit
these changes.

This patch was tested on the following cards:

1) BG card:

Atheros AR5213A chip found (MAC: 0x59, PHY: 0x43)
RF2112A 2GHz radio found (0x46)

2) ABG card:

Atheros AR5213A chip found (MAC: 0x59,PHY: 0x43)
RF5112A multiband radio found (0x36)

Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: implement cfg80211 station handling

This implements station handling from userspace via cfg80211
in mac80211.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: add beacon configuration via cfg80211

This patch implements the cfg80211 hooks for configuring beaconing
on an access point interface in mac80211. While doing so, it fixes
a number of races that could badly crash the machine when the
beacon is changed while being requested by the driver.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: move interface type to vif structure

Drivers that support mixed AP/STA operation may well need to
know the type of a virtual interface when iterating over them.
The easiest way to support that is to move the interface type
variable into the vif structure.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: dont use interface indices in drivers

This patch gets rid of the if_id stuff where possible in favour of
a new per-virtual-interface structure "struct ieee80211_vif". This
structure is located at the end of the per-interface structure and
contains a variable length driver-use data area.

This has two advantages:
 * removes the need to look up interfaces by if_id, this is better
   for working with network namespaces and performance
 * allows drivers to store and retrieve per-interface data without
   having to allocate own lists/hash tables

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add rtl8180 wireless driver

This patch adds a mac80211 based wireless driver for the rtl8180 and
rtl8185 PCI wireless cards.  Also included are some rtl8187 changes
required due to the relationship between that driver and this one.

Michael Wu is primarily responsible for the initial driver and rtl8185
support.  Andreas Merello provided the additional rtl8180 support.

Thanks to Jukka Ruohonen for the donating a rtl8185 card! It was very
helpful for the rtl8225z2 code.

The Signed-off-by information below is collected from the individual
patches submitted to wireless-2.6 before merging this driver upstream.

Signed-off-by: Andrea Merello <andreamrl@tiscali.it>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] Net: add ath5k wireless driver

add ath5k wireless driver

Portions of this driver are covered by one or both of the ISC and
3-clause BSD licenses.  Specific license information is cited at the top
of each file.

Acked-by and Signed-off-by information is collected from individual
patches as collected in the wireless-2.6 tree prior to upstream
submission.

Acked-by: Matthew W. S. Bell <mentor@madwifi.org>
Acked-by: Michael Taylor <mike.taylor@apprion.com>
Acked-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bradley M. Kuhn <bkuhn@softwarefreedom.org>
Signed-off-by: Bruno Randolf <bruno@thinktube.com>
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Francesco Gringoli <francesco.gringoli@ing.unibs.it>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Karen Sandler <karen@softwarefreedom.org>
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: Matt Norwood <norwood@softwarefreedom.org>
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Richard Fontana <fontana@softwarefreedom.org>
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Ulrich Meis <meis@nets.rwth-aachen.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: finish removal of pio support

As suggested in "b43: Remove PIO support"...

Signed-off-by: John W. Linville <linville@tuxdriver.com>

hostap_cs: don't match revisions in presense of the MAC chip name

If the third PCMCIA ID string specifies the MAC chip, the fourth ID
string doesn't need to be matched.  Even if it's different, it will be
compatible with the driver.

This ensures that other different revisions of the card will be
supported.

Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: Remove the PHY spinlock

This fixes a sparse warning about weird locking.
The spinlock is not needed, so simply remove it.
This also adds some sanity checks to the PHY and radio locking
to protect against recursive locking.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: Fix PHY register routing

This fixes the PHY routing bit handling.
This is needed for N-PHY.
No functional change to A-PHY and G-PHY code.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: Add N-PHY register definitions

This patch adds all register definitions for the N-PHY.
This adds two new files: nphy.h and nphy.c
No functional changes to existing code.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

zd1211rw: fix alignment for QOS and WDS frames

This patch fixes RX packet alignment issues in the zd1211rw driver.
This is based on a patch by Johannes Berg.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: fix compilation warning in 'iwl-4965.c'

This patch fixes a compilation warning in 'iwl-4965.c'.

"warning: format ‘%d’ expects type ‘int’, but argument 3 has type ‘long unsigned int’"

Signed-off-by: Miguel Botón <mboton@gmail.com
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Release rt2x00 2.0.14

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Correctly initialize data and desc pointer

rt2500usb and rt73usb store the descriptor in different
places. This means we should move the initialization of
the 2 pointers to the driver callback function fill_rxdone().

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Move init_txring and init_rxring into rt2x00lib

Prior to enabling the radio rt2x00lib should go through all
rings and for each entry should call the callback function
init_txentry() and init_rxentry().

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Determine MY_BSS from descriptor

Use the MY_BSS descriptor field to determine if the
received frame belongs to the same BSS as the interface.
This can be used by rxdone to determine if the frame
should be updated or not.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Cleanup write_tx_desc() arguments

Send the skb structure with write_tx_desc() and use
the skbdesc structure to read all information about
the frame. This saves several arguments in the function
definition and it is easier to send more information
later as well.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Move packet filter flags

The packet filter flags don't belong in the interface structure
because they are device based instead of interface based.
So move the filter fields out of struct interface and into rt2x00_dev.

Additionally we shouldn't change the filter based on the working
mode, if such a thing is needed than mac80211 should have done that.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Move start() and stop() handlers into rt2x00lib.c

suspend & resume was broken since it called rt2x00mac_start()
and rt2x00mac_stop() which would fail to execute because the
DEVICE_PRESENT flag was not set.

Move the start and stop handlers into rt2x00lib.c which are called
from rt2x00mac_start() and rt2x00mac_stop() after they have checked
the DEVICE_PRESENT flag, while suspend and resume handlers can
directly call those functions.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Store queue idx and entry idx in data_ring and data_entry

Store the queue idx inside structure data_ring
Store the entry idx inside structure data_entry
This saves us a few calls to ARRAY_INDEX() which is now unused.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Only set the TBCN flag when the interface is configured to send beacons.

These flags used to be fixed to one in rt2500pci_config_type, which
caused the beacon timer interrupt to fire. This would lead to
rt2x00lib_beacondone adding work which called
rt2x00lib_beacondone_scheduled which called ieee80211_beacon_get which
printed an error about not having any beacon data.

With this patch, these interrupts are only generated when the interface
is configured to send beacons.

Signed-off-by: Matthijs Kooijman <matthijs@stdin.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Always call ieee80211_stop_queue() when return NETDEV_TX_BUSY

Apparently it was possible that ieee80211_stop_queue() was not full while
NETDEV_TX_BUSY was being reported back. I think that is what causing the WARN_ON().
This moves all calls to ieee80211_stop_queue() in rt2x00mac.c where it is easier
to determine if the queue should be halted.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Fix chipset debugfs file

Initialize blob->data before moving the data pointer
Initialize blob->size based on blob->data size

This fixes the empty chipset file in debugfs.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: Fix any N-PHY related WARN_ON() in the attach stage.

This fixes all WARN_ON()s in the attach stage.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: Add NPHY kconfig option

This adds a new Kconfig option for enabling probing of N-PHYs.
This option will be removed again once the stuff works.
For now it is to help in development. This way real users won't
execute the broken N-PHY codepaths, but the developers can easily
enable N-PHY stuff.

To enable N-PHY probing simply remove the BROKEN dependency
and enable the option in the kernel config.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43-ssb-bridge: Add PCI ID for BCM43XG

This adds the PCI ID 0x4329 for the BCM43XG.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b44: power down PHY when interface down

This is just this patch (http://lkml.org/lkml/2007/7/1/51) but adapted
to the 'b44' ssb driver.

Signed-off-by: Miguel Botón <mboton@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ssb: add 'ssb_pcihost_set_power_state' function

This patch adds the 'ssb_pcihost_set_power_state' function.

This function allows us to set the power state of a PCI device
(for example b44 ethernet device).

Signed-off-by: Miguel Botón <mboton@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: Add definitions for MAC Control register

This adds some definitions for the MAC Control register
and uses them.
This basically is no functional change.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: Remove PIO support

Remove b43 PIO support.
DMA works well on all supported devices. There's no reason to use PIO.
Additionally, new devices don't support PIO in hardware anymore.
b43 PIO support is dead and unused code.

After applying this patch please do
git rm drivers/net/wireless/b43/pio.h
git rm drivers/net/wireless/b43/pio.c
to remove the main PIO support code.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ssb: Fix PCMCIA lowlevel register access

This fixes lowlevel register access for PCMCIA based devices.

The patch also adds a temporary workaround for the device mac address.
It simply adds generation of a random address. The real SPROM extraction
will follow in another patch.
The temporary workaround will be removed then, but for now it's OK.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: Fix chip access validation for new devices

This fixes chip access validation for newer devices
(4318 and up, I think)

This patch fixes probing of a PCMCIA based 4318 device.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: Only select allowed TX and RX antennas

This fixes antenna selection in b43. It adds a sanity check
for the antenna numbers we get from mac80211.

This patch depends on
ssb: Fix extraction of values from SPROM

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ssb: Fix extraction of values from SPROM

This fixes extraction of some values from the SPROM.
It mainly fixes extraction of antenna related values, which
is needed for another b43 fix sent later.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: fix typo in 'drivers/net/wireless/iwlwifi/Kconfig'

Based on a patch by Miguel.

Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Cc: Miguel Boton <mboton.lkml@gmail.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

prism54: remove questionable down_interruptible usage

Reviewing the semaphore usage I noticed these down_interruptible calls.  Most
of these aren't returning anything, so a caller can't tell if the operation
completed or not.  prism54_wpa_bss_ie_get() returns zero, but it's treated as
the function failing which doesn't seem correct.

Signed-off-by: Daniel Walker <dwalker@mvista.com>
Cc: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Revert "rtl8187: fix tx power reading"

This reverts commit e4128a54d790658ab265c915e5da9153ff74af97.

On Sunday 02 December 2007 17:17:51 Michael Wu wrote:
> CCK and OFDM power levels are stored in adjacent bytes, not nibbles.
>
This turns out to be true only for rtl8180. On rtl8187, power levels are
indeed stored in nibbles, so this patch is wrong. Please revert this patch.

Signed-off-by: John W. Linville <linville@tuxdriver.com>

misc wireless annotations

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ipw2200: do not byteswap struct ipw_associate

keep it little-endian, update places that use its members

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ipw2200 trivial annotations

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

prism54 trivial annotations

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcm43xx annotations

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

p54pci: endianness annotations and fixes

->ring_control_dma is dma_addr_t, needs conversion to little-endian
before __raw_writel()...

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

hostap: don't mess with mixed-endian even for internal skb queues

Just leave hfa384x_info_frame as-is, don't convert in place.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

hostap annotations

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

airo: last of endianness annotations

sanitize handling of ConfigRid

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

airo: sanitize handling of StatusRid

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

airo: sanitize APListRid handling

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

airo: sanitize handling of CapabilityRid

Don't byteswap any fields, annotate.  That has caught a bug,
BTW - will be handled in the next patch.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

airo: sanitize handling of StatsRid

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

airo: sanitize handling of WepKeyRid

don't byteswap, update users to match that, annotate.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

airo: sanitize BSSListRid handling

Stop byteswap-in-place in readBSSListRid(), annotate the sucker.
BTW, that had immediately found a bug - another codepath fetching
the same struct from card did _not_ byteswap, but used ->dBm the
same as everything else - host-endian.  Fix in the next patch...

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bap_read()/bap_write() work with fixed-endian buffers

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

airo: sanitize handling of SSID_rid

* store SSID_rid without conversions
* sanitize proc_SSID_on_close() (and avoid access past the end of
  buffer, while we are at it)

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

airo: trivial endianness annotations

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ipw2200: ipw_tx_skb() endianness bug

We'd just set tfd->u.data.chunk_len[i] to cpu_to_le16(remaining_bytes);
passing it to pci_map_single() is a bad idea - it expects host-endian.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ipw2200 fix: ->rt_chbitmask is le16

A couple of places forgot cpu_to_le16() in assignments to
that field, even though right next to those in other branches
of if-else we do it correctly.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ipw2200 fix: struct ieee80211_radiotap_header is little-endian

some places in driver forget conversions

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ray_cs fixes

bugs galore:
* 0xf380 instead of htons(ETH_P_AARP), etc.  Works only on l-e.
* back in 2.3.20 driver got readb() and friends instead of
direct dereferencing of iomem.  Somebody got too enthusiatic and replaced
ntohs(p->mrx_overflow)
with
ntohs(read(&p->mrx_overflow)
without noticing that (a) the sucker is 16bit and (b) that expression can't possibly
be portable anyway (hell, on l-e it's always less than 256, on b-e it's always a
multiple of 256).  Proper fix is
swab16(readw(&p->mrx_overflow)
taking into account the conversion done by readw() itself.  That crap happened
in several places; the same fix applies.
* untranslate() assumes little-endian almost everywhere, except for
the code checking for IPX/AARP packets; there we forgot ntohs(), so that part
only works on big-endian.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ipw2100 annotations and fixes

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

p54common annotations and fixes

* ->exp_id in bootrec_exp_if is __le16; missing conversion in its use
* !(x & y) misspelled as !x & y

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

hostap: fix endianness with txdesc->sw_support

it's le32, not le16...

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

airo: fix writerids() endianness

in writerids() we do _not_ byteswap, so we want to access
->opmode as little-endian.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

airo endianness bug: cap_rid.extSoftCap

never had been byteswapped, used as host-endian...

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

airo: bug in airo_interrupt() handling on incoming 802.11

On big-endian we end up with swapped first two bytes in packet,
due to earlier conversion to host-endian and forgotten conversion
back.

The code we calculated that host-endian for had been duplicated
several time - it finds the 802.11 MAC header length by the first
two bytes of packet; taken into a new helper (header_len(__le16 ctl)).

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

airo: fix endianness bug in ->dBm handling

airo_translate_scan() reads BSSListRid directly, does _not_ byteswap
and uses ->dBm (__le16) as host-endian.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

airo: fix transmit_802_11_packet()

a) gaplen would better be stored little-endian
b) for control packets (shorter than 24-byte header) we ended up with
        bap_write(ai, hdrlen == 30 ?
                (const u16*)&gap.gaplen : (const u16*)&gap, 38 - hdrlen, BAP1);
passing to card the data past the end of gap (i.e. random stuff from stack)
and did _not_ feed the gaplen at the right offset.
c) sending the contents of uninitialized fields of struct is Not Nice(tm) either

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ieee80211: beacon->capability is little-endian

It's only a debugging printk, so it went unnoticed; still, the
fix is trivial, so...

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ieee80211: fix misannotations

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ieee80211softmac_auth_resp() fix

The struct ieee8021_auth * passed to it comes straight from skb->data
without any conversions; members of the struct are little-endian, so
we'd better take that into account when doing switch by auth->algorithm,
etc.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

several missing cpu_to_le16() in ieee80211softmac_capabilities()

on some codepaths we forgot to convert to little-endian as we do on the
rest of them and as the caller expects from us.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

eliminate byteswapping in struct ieee80211_qos_parameters

Make it match the on-the-wire endianness, eliminate byteswapping.
The only driver that used this sucker (ipw2200) updated.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: cleanup some merge errors

Signed-off-by: John W. Linville <linville@tuxdriver.com>

[IPV4]: Enable use of 240/4 address space.

This short patch modifies the IPv4 networking to enable use of the
240.0.0.0/4 (aka "class-E") address space as propsed in the internet
draft draft-fuller-240space-00.txt.

Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

[NET] gen_estimator: gen_replace_estimator() cosmetic changes

White spaces etc. are changed in gen_replace_estimator() to make it
similar to others in a file.

Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[PKT_SCHED] net: add sparse annotation to ptype_seq_start/stop

Get rid of some more sparse warnings.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[PKT_SCHED] net classifier: style cleanup's

Classifier code cleanup. Get rid of printk wrapper, and fix whitespace
and other style stuff reported by checkpatch

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[PKT_SCHED] sch_atm: style cleanup

ATM scheduler clean house:
  * get rid of printk and qdisc_priv() wrapper
  * split some assignment in if() statements
  * whitespace and line breaks.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[PKT_SCHED] dsmark: checkpatch warning cleanup

Get rid of all style things checkpatch warns about, indentation and
whitespace.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[PKT_SCHED] dsmark: handle cloned and non-linear skb's

Make dsmark work properly with non-linear and cloned skb's
Before modifying the header, it needs to check that skb header is
writeable.

Note: this makes the assumption, that if it queues a good skb
then a good skb will come out of the embedded qdisc.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[PKT_SCHED] dsmark: Use hweight32() instead of convoluted loop.

Based upon a patch by Stephen Hemminger and suggestions
from Patrick McHardy.

Signed-off-by: David S. Miller <davem@davemloft.net>

[PKT_SCHED] dsmark: get rid of wrappers

Remove extraneous macro wrappers for printk and qdisc_priv.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[IPV6]: addrconf sparse warnings

Get rid of a couple of sparse warnings in IPV6 addrconf code.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[NET_SCHED]: kill obsolete NET_CLS_POLICE option

The code is already gone for about half a year, the config option
has been kept around to select the replacement options for easier
upgrades. This seems long enough, people upgrading from older
kernels will have to reconfigure a lot anyway.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

[MACVLAN]: Fix thinko in macvlan_transfer_operstate()

When the lower device's carrier is off, the macvlan devices's
carrier state should be checked to decide whether it needs to
be turned off. Currently the lower device's state is checked
a second time.

This still works, but unnecessarily tries to turn off the
carrier when its already off.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

[VLAN]: Move protocol determination to seperate function

I think, that we can make this code flow easier to understand
by introducing the vlan_set_encap_proto() function (I hope the
name is good) to setup the skb proto and merge the paths calling
netif_rx() together.

[Patrick: Modified to apply on top of my previous patches]

Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

[VLAN]: Clean up vlan_skb_recv()

- remove three instances of identical code
- remove unnecessary NULL initialization
- remove obvious and unnecessary comments

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

[VLAN]: Update list address

VLAN related mail should go to netdev.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

[VLAN]: checkpatch cleanups

Checkpatch cleanups, consisting mainly of overly long lines and
missing spaces.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>