sfrench/cifs-2.6.git
3 years agoInput: synaptics-rmi4 - limit the range of what GPIOs are buttons
Andrew Duggan [Wed, 25 Oct 2017 16:30:16 +0000 (09:30 -0700)]
Input: synaptics-rmi4 - limit the range of what GPIOs are buttons

By convention the first 6 bits of F30 Ctrl 2 and 3 are used to signify
GPIOs which are connected to buttons. Additional GPIOs may be used as
input GPIOs to signal the touch controller of some event
(ie disable touchpad). These additional GPIOs may meet the criteria of
a button in rmi_f30_is_valid_button() but should not be considered
buttons. This patch limits the GPIOs which are mapped to buttons to just
the first 6.

Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reported-by: Daniel Martin <consume.noise@gmail.com>
Tested-by: Daniel Martin <consume.noise@gmail.com>
Acked-By: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: gtco - fix potential out-of-bound access
Dmitry Torokhov [Mon, 23 Oct 2017 23:46:00 +0000 (16:46 -0700)]
Input: gtco - fix potential out-of-bound access

parse_hid_report_descriptor() has a while (i < length) loop, which
only guarantees that there's at least 1 byte in the buffer, but the
loop body can read multiple bytes which causes out-of-bounds access.

Reported-by: Andrey Konovalov <andreyknvl@google.com>
Reviewed-by: Andrey Konovalov <andreyknvl@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: elan_i2c - add ELAN0611 to the ACPI table
Kai-Heng Feng [Tue, 24 Oct 2017 18:08:18 +0000 (11:08 -0700)]
Input: elan_i2c - add ELAN0611 to the ACPI table

ELAN0611 touchpad uses elan_i2c as its driver. It can be found
on Lenovo ideapad 320-15IKB.

So add it to ACPI table to enable the touchpad.

[Ido Adiv <idoad123@gmail.com> reports that the same ACPI ID is used for
Elan touchpad in ideapad 520].

BugLink: https://bugs.launchpad.net/bugs/1723736
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: do not use property bits when generating module alias
Dmitry Torokhov [Sun, 22 Oct 2017 18:42:29 +0000 (11:42 -0700)]
Input: do not use property bits when generating module alias

The commit 8724ecb07229 ("Input: allow matching device IDs on property
bits") started using property bits when generating module aliases for input
handlers, but did not adjust the generation of MODALIAS attribute on input
device uevents, breaking automatic module loading. Given that no handler
currently uses property bits in their module tables, let's revert this part
of the commit for now.

Reported-by: Damien Wyart <damien.wyart@gmail.com>
Tested-by: Damien Wyart <damien.wyart@gmail.com>
Fixes: 8724ecb07229 ("Input: allow matching device IDs on property bits")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: ims-psu - check if CDC union descriptor is sane
Dmitry Torokhov [Sat, 7 Oct 2017 18:07:47 +0000 (11:07 -0700)]
Input: ims-psu - check if CDC union descriptor is sane

Before trying to use CDC union descriptor, try to validate whether that it
is sane by checking that intf->altsetting->extra is big enough and that
descriptor bLength is not too big and not too small.

Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: joydev - blacklist ds3/ds4/udraw motion sensors
Roderick Colenbrander [Mon, 9 Oct 2017 19:02:03 +0000 (12:02 -0700)]
Input: joydev - blacklist ds3/ds4/udraw motion sensors

Introduce a device table used for blacklisting devices. We currently
blacklist the motion sensor subdevice of THQ Udraw and Sony ds3/ds4.

Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
[dtor: siwtched to blacklist built on input_device_id and using
input_match_device_id()]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: allow matching device IDs on property bits
Dmitry Torokhov [Mon, 9 Oct 2017 19:01:14 +0000 (12:01 -0700)]
Input: allow matching device IDs on property bits

Let's allow matching input devices on their property bits, both in-kernel
and when generating module aliases.

Tested-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: factor out and export input_device_id matching code
Dmitry Torokhov [Mon, 9 Oct 2017 18:09:33 +0000 (11:09 -0700)]
Input: factor out and export input_device_id matching code

Factor out and export input_match_device_id() so that modules may use it.
It will be needed by joydev to blacklist accelerometers in composite
devices.

Tested-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: goodix - poll the 'buffer status' bit before reading data
Paul Cercueil [Fri, 13 Oct 2017 18:04:48 +0000 (11:04 -0700)]
Input: goodix - poll the 'buffer status' bit before reading data

The Goodix panel triggers an interrupt on touch events. However, its
registers will contain the valid values a short time after the
interrupt, and not when it's raised. At that moment, the 'buffer status'
bit is set.

Previously, if the 'buffer status' bit was not set when the registers
were read, the data was discarded and no input event was emitted,
causing "finger down" or "finger up" events to be missed sometimes.

This went unnoticed until v4.9, as the DesignWare I2C driver commonly
used with this driver had enough latency for that bug to never trigger
until commit 2702ea7dbec5 ("i2c: designware: wait for disable/enable only
if necessary").

Now, in the IRQ handler we will poll (with a timeout) the 'buffer status'
bit and process the data of the panel as soon as this bit gets set.

Note that the Goodix panel will send a few spurious interrupts after the
'finger up' event, in which the 'buffer status' bit will never be set.

Cc: Bastien Nocera <hadess@hadess.net>
Cc: russianneuromancer@ya.ru
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
[hdegoede@redhat.com: Change poll loop to use jiffies,
                      add comment about typical poll time]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[dtor: rearranged control flow a bit to avoid explicit goto and double
check]
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: axp20x-pek - fix module not auto-loading for axp221 pek
Hans de Goede [Thu, 19 Oct 2017 22:38:50 +0000 (15:38 -0700)]
Input: axp20x-pek - fix module not auto-loading for axp221 pek

Now that we have a platform_device_id table and multiple supported ids
we should be using MODULE_DEVICE_TABLE instead of MODULE_ALIAS.

This fixes a regression on Bay and Cherry Trail devices, where the power
button is now enumerated as an "axp221-pek" and it was impossible to
wakeup these devices from suspend since the module did not load.

Fixes: c3cc94470bd3 ("Input: axp20x-pek - add support for AXP221 PEK")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: tca8418 - enable interrupt after it has been requested
Damien Riegel [Thu, 19 Oct 2017 22:34:55 +0000 (15:34 -0700)]
Input: tca8418 - enable interrupt after it has been requested

Currently, enabling keypad interrupts is one of the first operations
done on the keypad, even before the interrupt is requested, so there is
a small time window where the keypad can fire interrupts but the driver
is not yet ready to handle them. It's fine for level interrupts because
they will be handled anyway, but not so much for edge ones.

This commit modifies and moves the function in charge of configuring the
keypad. Enabling interrupts is now the last thing done on the keypad,
and after the interrupt has been requested by the driver.

Writing to the config register was also used to determine if the device
was indeed present on the bus or not, this has been replaced by reading
the lock/event count register to keep the same functionality.

Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: stmfts - fix setting ABS_MT_POSITION_* maximum size
Chanwoo Choi [Thu, 19 Oct 2017 00:28:36 +0000 (17:28 -0700)]
Input: stmfts - fix setting ABS_MT_POSITION_* maximum size

The commit 78bcac7b2ae1e ("Input: add support for the STMicroelectronics
FingerTip touchscreen) used the 'touchscreen_parse_properties()' helper
function in order to get the value of common properties.

But, commit 78bcac7b2ae1e didn't set the capability of ABS_MT_POSITION_*
before calling touchscreen_parse_properties(). In result, the max_x and
max_y of 'struct touchscreen_properties' were not set.

Fixes: 78bcac7b2ae1e ("Input: add support for the STMicroelectronics FingerTip touchscreen")
Cc: stable@vger.kernel.org
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: ti_am335x_tsc - fix incorrect step config for 5 wire touchscreen
Jeff Lance [Thu, 19 Oct 2017 00:25:52 +0000 (17:25 -0700)]
Input: ti_am335x_tsc - fix incorrect step config for 5 wire touchscreen

Step config setting for 5 wire touchscreen is incorrect for Y coordinates.
It was broken while we moved to DT. If you look close at the offending
commit bb76dc09ddfc ("input: ti_am33x_tsc: Order of TSC wires, made
configurable"), the change was:

- STEPCONFIG_XNP | STEPCONFIG_YPN;
+ ts_dev->bit_xn | ts_dev->bit_yp;

while bit_xn = STEPCONFIG_XNN and bit_yp = STEPCONFIG_YNN. Not quite the
same.

Fixes: bb76dc09ddfc ("input: ti_am33x_tsc: Order of TSC wires, made configurable")
Signed-off-by: Jeff Lance <j-lance1@ti.com>
[vigneshr@ti.com: Rebase to v4.14-rc1]
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Michael Nazzareno Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: synaptics - disable kernel tracking on SMBus devices
Andrew Duggan [Tue, 10 Oct 2017 03:51:05 +0000 (20:51 -0700)]
Input: synaptics - disable kernel tracking on SMBus devices

In certain situations kernel tracking seems to be getting confused
and incorrectly reporting the slot of a contact. On example is when
the user does a three finger click or tap and then places two fingers
on the touchpad in the same area. The kernel tracking code seems to
continue to think that there are three contacts on the touchpad and
incorrectly alternates the slot of one of the contacts. The result that
is the input subsystem reports a stream of button press and release
events as the reported slot changes.

Kernel tracking was originally enabled to prevent cursor jumps, but it
is unclear how much of an issue kernel jumps actually are. This patch
simply disabled kernel tracking for now.

Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1482640

Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Tested-by: Kamil Páral <kparal@redhat.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: elan_i2c - extend Flash-Write delay
KT Liao [Fri, 22 Sep 2017 17:00:57 +0000 (10:00 -0700)]
Input: elan_i2c - extend Flash-Write delay

The original 20ms delay is only marginally enough delay after a block write
operation during firmware update. Let's increase the delay to ensure that
the controller finishes up storing the page to avoid failures in the
firmware updates.

Signed-off-by: KT Liao <kt.liao@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: uinput - avoid crash when sending FF request to device going away
Dmitry Torokhov [Wed, 6 Sep 2017 23:22:59 +0000 (16:22 -0700)]
Input: uinput - avoid crash when sending FF request to device going away

If FF request comes in while uinput device is going away,
uinput_request_send() will fail with -ENODEV, and uinput_request_submit()
will attempt to mark the slot as unused by calling uinput_request_done().
Unfortunately in this case we haven't initialized request->done completion
yet, and we get a crash:

[   39.402036] BUG: spinlock bad magic on CPU#1, fftest/3108
[   39.402046]  lock: 0xffff88006a93bb00, .magic: 00000000, .owner: /39, .owner_cpu: 1217155072
[   39.402055] CPU: 1 PID: 3108 Comm: fftest Tainted: G        W 4.13.0+ #15
[   39.402059] Hardware name: LENOVO 20HQS0EG02/20HQS0EG02, BIOS N1MET37W (1.22 ) 07/04/2017
[   39.402064]  0000000000000086 f0fad82f3ceaa120 ffff88006a93b9a0 ffffffff9de941bb
[   39.402077]  ffff88026df8ae00 ffff88006a93bb00 ffff88006a93b9c0 ffffffff9dca62b7
[   39.402088]  ffff88006a93bb00 ffff88006a93baf8 ffff88006a93b9e0 ffffffff9dca62e7
[   39.402099] Call Trace:
[   39.402112]  [<ffffffff9de941bb>] dump_stack+0x4d/0x63
[   39.402123]  [<ffffffff9dca62b7>] spin_dump+0x97/0x9c
[   39.402130]  [<ffffffff9dca62e7>] spin_bug+0x2b/0x2d
[   39.402138]  [<ffffffff9dca6373>] do_raw_spin_lock+0x28/0xfd
[   39.402147]  [<ffffffff9e3055cd>] _raw_spin_lock_irqsave+0x19/0x1f
[   39.402154]  [<ffffffff9dca05b7>] complete+0x1d/0x48
[   39.402162]  [<ffffffffc04f30af>] 0xffffffffc04f30af
[   39.402167]  [<ffffffffc04f468c>] 0xffffffffc04f468c
[   39.402177]  [<ffffffff9dd59c16>] ? __slab_free+0x22f/0x359
[   39.402184]  [<ffffffff9dcc13e9>] ? tk_clock_read+0xc/0xe
[   39.402189]  [<ffffffffc04f471f>] 0xffffffffc04f471f
[   39.402195]  [<ffffffff9dc9ffe5>] ? __wake_up+0x44/0x4b
[   39.402200]  [<ffffffffc04f3240>] ? 0xffffffffc04f3240
[   39.402207]  [<ffffffff9e0f57f3>] erase_effect+0xa1/0xd2
[   39.402214]  [<ffffffff9e0f58c6>] input_ff_flush+0x43/0x5c
[   39.402219]  [<ffffffffc04f32ad>] 0xffffffffc04f32ad
[   39.402227]  [<ffffffff9e0f174f>] input_flush_device+0x3d/0x51
[   39.402234]  [<ffffffff9e0f69ae>] evdev_flush+0x49/0x5c
[   39.402243]  [<ffffffff9dd62d6e>] filp_close+0x3f/0x65
[   39.402253]  [<ffffffff9dd7dcf7>] put_files_struct+0x66/0xc1
[   39.402261]  [<ffffffff9dd7ddeb>] exit_files+0x47/0x4e
[   39.402270]  [<ffffffff9dc6b329>] do_exit+0x483/0x969
[   39.402278]  [<ffffffff9dc73211>] ? recalc_sigpending_tsk+0x3d/0x44
[   39.402285]  [<ffffffff9dc6c7a2>] do_group_exit+0x42/0xb0
[   39.402293]  [<ffffffff9dc767e1>] get_signal+0x58d/0x5bf
[   39.402300]  [<ffffffff9dc03701>] do_signal+0x37/0x53e
[   39.402307]  [<ffffffff9e0f8401>] ? evdev_ioctl_handler+0xac8/0xb04
[   39.402314]  [<ffffffff9e0f8464>] ? evdev_ioctl+0x10/0x12
[   39.402321]  [<ffffffff9dd74cfa>] ? do_vfs_ioctl+0x42e/0x501
[   39.402328]  [<ffffffff9dc0170e>] prepare_exit_to_usermode+0x66/0x90
[   39.402333]  [<ffffffff9dc0181b>] syscall_return_slowpath+0xe3/0xec
[   39.402339]  [<ffffffff9e305b7b>] int_ret_from_sys_call+0x25/0x8f

While we could solve this by simply initializing the completion earlier, we
are better off rearranging the code a bit so we avoid calling complete() on
requests that we did not send out. This patch consolidates marking request
slots as free in one place (in uinput_request_submit(), the same place
where we acquire them) and having everyone else simply signal completion
of the requests.

Fixes: 00ce756ce53a ("Input: uinput - mark failed submission requests as free")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: uinput - avoid FF flush when destroying device
Dmitry Torokhov [Sat, 2 Sep 2017 00:13:43 +0000 (17:13 -0700)]
Input: uinput - avoid FF flush when destroying device

Normally, when input device supporting force feedback effects is being
destroyed, we try to "flush" currently playing effects, so that the
physical device does not continue vibrating (or executing other effects).
Unfortunately this does not work well for uinput as flushing of the effects
deadlocks with the destroy action:

- if device is being destroyed because the file descriptor is being closed,
  then there is noone to even service FF requests;

- if device is being destroyed because userspace sent UI_DEV_DESTROY,
  while theoretically it could be possible to service FF requests,
  userspace is unlikely to do so (they'd need to make sure FF handling
  happens on a separate thread) even if kernel solves the issue with FF
  ioctls deadlocking with UI_DEV_DESTROY ioctl on udev->mutex.

To avoid lockups like the one below, let's install a custom input device
flush handler, and avoid trying to flush force feedback effects when we
destroying the device, and instead rely on uinput to shut off the device
properly.

NMI watchdog: Watchdog detected hard LOCKUP on cpu 3
...
 <<EOE>>  [<ffffffff817a0307>] _raw_spin_lock_irqsave+0x37/0x40
 [<ffffffff810e633d>] complete+0x1d/0x50
 [<ffffffffa00ba08c>] uinput_request_done+0x3c/0x40 [uinput]
 [<ffffffffa00ba587>] uinput_request_submit.part.7+0x47/0xb0 [uinput]
 [<ffffffffa00bb62b>] uinput_dev_erase_effect+0x5b/0x76 [uinput]
 [<ffffffff815d91ad>] erase_effect+0xad/0xf0
 [<ffffffff815d929d>] flush_effects+0x4d/0x90
 [<ffffffff815d4cc0>] input_flush_device+0x40/0x60
 [<ffffffff815daf1c>] evdev_cleanup+0xac/0xc0
 [<ffffffff815daf5b>] evdev_disconnect+0x2b/0x60
 [<ffffffff815d74ac>] __input_unregister_device+0xac/0x150
 [<ffffffff815d75f7>] input_unregister_device+0x47/0x70
 [<ffffffffa00bac45>] uinput_destroy_device+0xb5/0xc0 [uinput]
 [<ffffffffa00bb2de>] uinput_ioctl_handler.isra.9+0x65e/0x740 [uinput]
 [<ffffffff811231ab>] ? do_futex+0x12b/0xad0
 [<ffffffffa00bb3f8>] uinput_ioctl+0x18/0x20 [uinput]
 [<ffffffff81241248>] do_vfs_ioctl+0x298/0x480
 [<ffffffff81337553>] ? security_file_ioctl+0x43/0x60
 [<ffffffff812414a9>] SyS_ioctl+0x79/0x90
 [<ffffffff817a04ee>] entry_SYSCALL_64_fastpath+0x12/0x71

Reported-by: Rodrigo Rivas Costa <rodrigorivascosta@gmail.com>
Reported-by: Clément VUCHENER <clement.vuchener@gmail.com>
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=193741
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoMerge branch 'next' into for-linus
Dmitry Torokhov [Fri, 15 Sep 2017 16:52:21 +0000 (09:52 -0700)]
Merge branch 'next' into for-linus

Prepare second round of input updates for 4.14 merge window.

3 years agoInput: i8042 - add Gigabyte P57 to the keyboard reset table
Kai-Heng Feng [Fri, 15 Sep 2017 16:36:16 +0000 (09:36 -0700)]
Input: i8042 - add Gigabyte P57 to the keyboard reset table

Similar to other Gigabyte laptops, the touchpad on P57 requires a
keyboard reset to detect Elantech touchpad correctly.

BugLink: https://bugs.launchpad.net/bugs/1594214
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: xpad - validate USB endpoint type during probe
Cameron Gutman [Tue, 12 Sep 2017 18:27:44 +0000 (11:27 -0700)]
Input: xpad - validate USB endpoint type during probe

We should only see devices with interrupt endpoints. Ignore any other
endpoints that we find, so we don't send try to send them interrupt URBs
and trigger a WARN down in the USB stack.

Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Cc: <stable@vger.kernel.org> # c01b5e7464f0 Input: xpad - don't depend on endpoint order
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: ucb1400_ts - fix suspend and resume handling
Dmitry Torokhov [Fri, 1 Sep 2017 01:23:11 +0000 (18:23 -0700)]
Input: ucb1400_ts - fix suspend and resume handling

Instead of stopping the touchscreen we were starting it in suspend, and
disabling it in resume.

Fixes: c899afedf168 ("Input: ucb1400_ts - convert to threaded IRQ")
Reported-by: Anton Volkov <avolkov@ispras.ru>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: edt-ft5x06 - fix access to non-existing register
Luca Ceresoli [Thu, 7 Sep 2017 21:28:28 +0000 (14:28 -0700)]
Input: edt-ft5x06 - fix access to non-existing register

reg_addr->reg_report_rate is supposed to exist in M06, not M09.

The driver is written to skip avoids access to non-existing registers
when the register address is NO_REGISTER (0xff). But
reg_addr->reg_report_rate is initialized to 0x00 by devm_kzalloc() (in
edt_ft5x06_ts_probe()) and not changed thereafter. So the checks do
not work and an access to register 0x00 is done.

Fix by setting reg_addr->reg_report_rate to NO_REGISTER.

Also fix the only place where reg_report_rate is checked against zero
instead of NO_REGISTER.

Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: elantech - make arrays debounce_packet static, reduces object code size
Colin Ian King [Thu, 7 Sep 2017 21:27:26 +0000 (14:27 -0700)]
Input: elantech - make arrays debounce_packet static, reduces object code size

Don't populate the arrays debounce_packet on the stack, instead make
them static.  Makes the object code smaller by over 870 bytes:

Before:
   text    data     bss     dec     hex filename
  30553    9152       0   39705    9b19 drivers/input/mouse/elantech.o

After:
   text    data     bss     dec     hex filename
  29521    9312       0   38833    97b1 drivers/input/mouse/elantech.o

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: surface3_spi - make const array header static, reduces object code size
Colin Ian King [Thu, 7 Sep 2017 21:27:12 +0000 (14:27 -0700)]
Input: surface3_spi - make const array header static, reduces object code size

Don't populate the const array header on the stack, instead make it
static.  Makes the object code smaller by over 180 bytes:

Before:
   text    data     bss     dec     hex filename
   6003    1536       0    7539    1d73 surface3_spi.o

After:
   text    data     bss     dec     hex filename
   5726    1632       0    7358    1cbe surface3_spi.o

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: goodix - add support for capacitive home button
Sergei A. Trusov [Thu, 7 Sep 2017 00:29:24 +0000 (17:29 -0700)]
Input: goodix - add support for capacitive home button

On some x86 tablets with a Goodix touchscreen, the Windows logo on the
front is a capacitive home button. Touching this button results in a touch
with bit 4 of the first byte set, while only the lower 4 bits (0-3) are
used to indicate the number of touches.

Report a KEY_LEFTMETA press when this happens.

Note that the hardware might support more than one button, in which
case the "id" byte of coor_data would identify the button in question.
This is not implemented as we don't have access to hardware with
multiple buttons.

Signed-off-by: Sergei A. Trusov <sergei.a.trusov@ya.ru>
Acked-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: add a driver for PWM controllable vibrators
Sebastian Reichel [Mon, 4 Sep 2017 16:30:03 +0000 (09:30 -0700)]
Input: add a driver for PWM controllable vibrators

Provide a simple driver for PWM controllable vibrators.
It will be used by Motorola Droid 4.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: adi - make array seq static, reduces object code size
Colin Ian King [Mon, 4 Sep 2017 16:17:39 +0000 (09:17 -0700)]
Input: adi - make array seq static, reduces object code size

Don't populate the array seq on the stack, instead make it static.
Makes the object code smaller by over 170 bytes:

Before:
   text    data     bss     dec     hex filename
  13227    3232       0   16459    404b drivers/input/joystick/adi.o

After:
   text    data     bss     dec     hex filename
  12957    3328       0   16285    3f9d drivers/input/joystick/adi.o

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoMerge branch 'next' into for-linus
Dmitry Torokhov [Mon, 4 Sep 2017 16:22:54 +0000 (09:22 -0700)]
Merge branch 'next' into for-linus

Prepare input updates for 4.14 merge window.

3 years agoInput: byd - make array seq static, reduces object code size
Colin Ian King [Thu, 31 Aug 2017 16:30:44 +0000 (09:30 -0700)]
Input: byd - make array seq static, reduces object code size

Don't populate the array seq on the stack, instead make it static.
Makes the object code smaller by over 1100 bytes:

Before:
   text    data     bss     dec     hex filename
   6152    1216      64    7432    1d08 drivers/input/mouse/byd.o

After:
   text    data     bss     dec     hex filename
   4974    1280      64    6318    18ae drivers/input/mouse/byd.o

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: xilinx_ps2 - fix multiline comment style
Michal Simek [Thu, 31 Aug 2017 21:55:45 +0000 (14:55 -0700)]
Input: xilinx_ps2 - fix multiline comment style

Fix multiline comments style not to be reported by checkpatch.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: pxa27x_keypad - handle return value of clk_prepare_enable
Arvind Yadav [Thu, 31 Aug 2017 18:39:13 +0000 (11:39 -0700)]
Input: pxa27x_keypad - handle return value of clk_prepare_enable

clk_prepare_enable() can fail here and we must check its return value.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: tegra-kbc - handle return value of clk_prepare_enable
Arvind Yadav [Thu, 31 Aug 2017 18:35:29 +0000 (11:35 -0700)]
Input: tegra-kbc - handle return value of clk_prepare_enable

clk_prepare_enable() can fail here and we must check its return value.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: xpad - fix PowerA init quirk for some gamepad models
Cameron Gutman [Thu, 31 Aug 2017 18:52:20 +0000 (11:52 -0700)]
Input: xpad - fix PowerA init quirk for some gamepad models

The PowerA gamepad initialization quirk worked with the PowerA
wired gamepad I had around (0x24c6:0x543a), but a user reported [0]
that it didn't work for him, even though our gamepads shared the
same vendor and product IDs.

When I initially implemented the PowerA quirk, I wanted to avoid
actually triggering the rumble action during init. My tests showed
that my gamepad would work correctly even if it received a rumble
of 0 intensity, so that's what I went with.

Unfortunately, this apparently isn't true for all models (perhaps
a firmware difference?). This non-working gamepad seems to require
the real magic rumble packet that the Microsoft driver sends, which
actually vibrates the gamepad. To counteract this effect, I still
send the old zero-rumble PowerA quirk packet which cancels the
rumble effect before the motors can spin up enough to vibrate.

[0]: https://github.com/paroj/xpad/issues/48#issuecomment-313904867

Reported-by: Kyle Beauchamp <kyleabeauchamp@gmail.com>
Tested-by: Kyle Beauchamp <kyleabeauchamp@gmail.com>
Fixes: 81093c9848a7 ("Input: xpad - support some quirky Xbox One pads")
Cc: stable@vger.kernel.org # v4.12
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: synaptics - fix device info appearing different on reconnect
Anthony Martin [Mon, 28 Aug 2017 17:26:12 +0000 (10:26 -0700)]
Input: synaptics - fix device info appearing different on reconnect

User-modified input settings no longer survive a suspend/resume cycle.
Starting with 4.12, the touchpad is reinitialized on every reconnect
because the hardware appears to be different. This can be reproduced
by running the following as root:

    echo -n reconnect >/sys/devices/platform/i8042/serio1/drvctl

A line like the following will show up in dmesg:

    [30378.295794] psmouse serio1: synaptics: hardware appears to be
                   different: id(149271-149271), model(114865-114865),
                   caps(d047b3-d047b1), ext(b40000-b40000).

Note the single bit difference in caps: bit 1 (SYN_CAP_MULTIFINGER).

This happens because we modify our stored copy of the device info
capabilities when we enable advanced gesture mode but this change is
not reflected in the actual hardware capabilities.

It worked in the past because synaptics_query_hardware used to modify
the stored synaptics_device_info struct instead of filling in a new
one, as it does now.

Fix it by no longer faking the SYN_CAP_MULTIFINGER bit when setting
advanced gesture mode. This necessitated a small refactoring.

Fixes: 6c53694fb222 ("Input: synaptics - split device info into a separate structure")
Signed-off-by: Anthony Martin <ality@pbrane.org>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: PS/2 gpio bit banging driver for serio bus
Danilo Krummrich [Mon, 28 Aug 2017 16:59:20 +0000 (09:59 -0700)]
Input: PS/2 gpio bit banging driver for serio bus

This driver provides PS/2 serio bus support by implementing bit banging
with the GPIO API. The GPIO pins, data and clock, can be configured with
a node in the device tree or by generic device properties (GDP).

Writing to a device is supported as well, though it is possible timings
can not be halt as they are tough and difficult to reach with bit banging.
Therefore it can be configured (also in DT and GDP) whether the serio
write function should be available for clients.

This driver is for development purposes and not recommended for productive
use. However, this driver can be useful e.g. when no USB port is available
or using old peripherals is desired as PS/2 controller chips getting rare.

This driver was tested on bcm2825 and on Kirin 960 and it worked well
together with the atkbd and psmouse driver.

Signed-off-by: Danilo Krummrich <danilokrummrich@dk-develop.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: xen-kbdfront - enable auto repeat for xen keyboard frontend driver
Liang Yan [Mon, 28 Aug 2017 16:41:08 +0000 (09:41 -0700)]
Input: xen-kbdfront - enable auto repeat for xen keyboard frontend driver

Long pressed key could not show right in XEN vncviewer after tigervnc
client changed the way how to send repeat keys, from "Down Up Down Up
..." to "Down Down ... Up". This will report autorepeat to input by
checking if same key being pressed, and let handler process it finally.

Signed-off-by: Liang Yan <lyan@suse.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: ambakmi - constify amba_id
Arvind Yadav [Wed, 23 Aug 2017 18:37:05 +0000 (11:37 -0700)]
Input: ambakmi - constify amba_id

amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: ALPS - fix two-finger scroll breakage in right side on ALPS touchpad
Masaki Ota [Thu, 24 Aug 2017 22:44:36 +0000 (15:44 -0700)]
Input: ALPS - fix two-finger scroll breakage in right side on ALPS touchpad

Fixed the issue that two finger scroll does not work correctly
on V8 protocol. The cause is that V8 protocol X-coordinate decode
is wrong at SS4 PLUS device. I added SS4 PLUS X decode definition.

Mote notes:
the problem manifests itself by the commit e7348396c6d5 ("Input: ALPS
- fix V8+ protocol handling (73 03 28)"), where a fix for the V8+
protocol was applied.  Although the culprit must have been present
beforehand, the two-finger scroll worked casually even with the
wrongly reported values by some reason.  It got broken by the commit
above just because it changed x_max value, and this made libinput
correctly figuring the MT events.  Since the X coord is reported as
falsely doubled, the events on the right-half side go outside the
boundary, thus they are no longer handled.  This resulted as a broken
two-finger scroll.

One finger event is decoded differently, and it didn't suffer from
this problem.  The problem was only about MT events. --tiwai

Fixes: e7348396c6d5 ("Input: ALPS - fix V8+ protocol handling (73 03 28)")
Signed-off-by: Masaki Ota <masaki.ota@jp.alps.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Paul Donohue <linux-kernel@PaulSD.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: atmel_mxt_ts - add support for reset line
Sebastian Reichel [Tue, 25 Jul 2017 21:11:34 +0000 (14:11 -0700)]
Input: atmel_mxt_ts - add support for reset line

Provide support for controlling reset pin. If this is not driven
correctly the device will be held in reset and will not respond.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: atmel_mxt_ts - use more managed resources
Sebastian Reichel [Tue, 25 Jul 2017 21:08:48 +0000 (14:08 -0700)]
Input: atmel_mxt_ts - use more managed resources

Switch mxt_data and interrupt to resource managed allocation methods,
which cleans up the driver slightly and prepares for adding
reset GPIO support.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: soc_button_array - silence -ENOENT error on Dell XPS13 9365
Hans de Goede [Sun, 20 Aug 2017 16:29:03 +0000 (09:29 -0700)]
Input: soc_button_array - silence -ENOENT error on Dell XPS13 9365

The Dell XPS13 9365 has an INT33D2 ACPI node with no GPIOs, causing
the following error in dmesg:

[    7.172275] soc_button_array: probe of INT33D2:00 failed with error -2

This commit silences this, by returning -ENODEV when there are no GPIOs.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=196679
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: wacom_w8001 - constify serio_device_id
Arvind Yadav [Sat, 19 Aug 2017 00:12:40 +0000 (17:12 -0700)]
Input: wacom_w8001 - constify serio_device_id

serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: tsc40 - constify serio_device_id
Arvind Yadav [Sat, 19 Aug 2017 00:12:29 +0000 (17:12 -0700)]
Input: tsc40 - constify serio_device_id

serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: touchwin - constify serio_device_id
Arvind Yadav [Sat, 19 Aug 2017 00:12:14 +0000 (17:12 -0700)]
Input: touchwin - constify serio_device_id

serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: touchright - constify serio_device_id
Arvind Yadav [Sat, 19 Aug 2017 00:12:03 +0000 (17:12 -0700)]
Input: touchright - constify serio_device_id

serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: touchit213 - constify serio_device_id
Arvind Yadav [Sat, 19 Aug 2017 00:11:56 +0000 (17:11 -0700)]
Input: touchit213 - constify serio_device_id

serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: penmount - constify serio_device_id
Arvind Yadav [Sat, 19 Aug 2017 00:11:48 +0000 (17:11 -0700)]
Input: penmount - constify serio_device_id

serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: mtouch - constify serio_device_id
Arvind Yadav [Sat, 19 Aug 2017 00:11:40 +0000 (17:11 -0700)]
Input: mtouch - constify serio_device_id

serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: inexio - constify serio_device_id
Arvind Yadav [Sat, 19 Aug 2017 00:11:32 +0000 (17:11 -0700)]
Input: inexio - constify serio_device_id

serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: hampshire - constify serio_device_id
Arvind Yadav [Sat, 19 Aug 2017 00:11:20 +0000 (17:11 -0700)]
Input: hampshire - constify serio_device_id

serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: gunze - constify serio_device_id
Arvind Yadav [Sat, 19 Aug 2017 00:11:12 +0000 (17:11 -0700)]
Input: gunze - constify serio_device_id

serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: fujitsu_ts - constify serio_device_id
Arvind Yadav [Sat, 19 Aug 2017 00:11:04 +0000 (17:11 -0700)]
Input: fujitsu_ts - constify serio_device_id

serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: elo - constify serio_device_id
Arvind Yadav [Sat, 19 Aug 2017 00:10:53 +0000 (17:10 -0700)]
Input: elo - constify serio_device_id

serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: dynapro - constify serio_device_id
Arvind Yadav [Sat, 19 Aug 2017 00:10:41 +0000 (17:10 -0700)]
Input: dynapro - constify serio_device_id

serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: wacom_serial4 - constify serio_device_id
Arvind Yadav [Sat, 19 Aug 2017 00:10:33 +0000 (17:10 -0700)]
Input: wacom_serial4 - constify serio_device_id

serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: constify serio_device_id
Arvind Yadav [Sat, 19 Aug 2017 00:10:24 +0000 (17:10 -0700)]
Input: constify serio_device_id

serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: xtkbd - constify serio_device_id
Arvind Yadav [Sat, 19 Aug 2017 00:10:13 +0000 (17:10 -0700)]
Input: xtkbd - constify serio_device_id

serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: sunkbd - constify serio_device_id
Arvind Yadav [Sat, 19 Aug 2017 00:10:05 +0000 (17:10 -0700)]
Input: sunkbd - constify serio_device_id

serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: stowaway - constify serio_device_id
Arvind Yadav [Sat, 19 Aug 2017 00:09:50 +0000 (17:09 -0700)]
Input: stowaway - constify serio_device_id

serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: newtonkbd - constify serio_device_id
Arvind Yadav [Sat, 19 Aug 2017 00:09:41 +0000 (17:09 -0700)]
Input: newtonkbd - constify serio_device_id

serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: lkkbd - constify serio_device_id
Arvind Yadav [Sat, 19 Aug 2017 00:09:31 +0000 (17:09 -0700)]
Input: lkkbd - constify serio_device_id

serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: hil_kbd - constify serio_device_id
Arvind Yadav [Sat, 19 Aug 2017 00:09:21 +0000 (17:09 -0700)]
Input: hil_kbd - constify serio_device_id

serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: iatkbd - constify serio_device_id
Arvind Yadav [Sat, 19 Aug 2017 00:09:14 +0000 (17:09 -0700)]
Input: iatkbd - constify serio_device_id

serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: zhenhua - constify serio_device_id
Arvind Yadav [Sat, 19 Aug 2017 00:09:05 +0000 (17:09 -0700)]
Input: zhenhua - constify serio_device_id

serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: warrior - constify serio_device_id
Arvind Yadav [Sat, 19 Aug 2017 00:08:52 +0000 (17:08 -0700)]
Input: warrior - constify serio_device_id

serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: twidjoy - constify serio_device_id
Arvind Yadav [Sat, 19 Aug 2017 00:08:41 +0000 (17:08 -0700)]
Input: twidjoy - constify serio_device_id

serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: stinger - constify serio_device_id
Arvind Yadav [Sat, 19 Aug 2017 00:08:29 +0000 (17:08 -0700)]
Input: stinger - constify serio_device_id

serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: spaceorb - constify serio_device_id
Arvind Yadav [Sat, 19 Aug 2017 00:08:17 +0000 (17:08 -0700)]
Input: spaceorb - constify serio_device_id

serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: spaceball - constify serio_device_id
Arvind Yadav [Sat, 19 Aug 2017 00:08:02 +0000 (17:08 -0700)]
Input: spaceball - constify serio_device_id

serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: magellan - constify serio_device_id
Arvind Yadav [Sat, 19 Aug 2017 00:07:48 +0000 (17:07 -0700)]
Input: magellan - constify serio_device_id

serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: iforce - constify serio_device_id
Arvind Yadav [Sat, 19 Aug 2017 00:07:32 +0000 (17:07 -0700)]
Input: iforce - constify serio_device_id

serio_device_id are not supposed to change at runtime. All functions
working with serio_device_id provided by <linux/serio.h> work with
const serio_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: elan_i2c - support touchpads with two physical buttons
KT Liao [Fri, 18 Aug 2017 23:49:53 +0000 (16:49 -0700)]
Input: elan_i2c - support touchpads with two physical buttons

Elan touchpads on Asus ROG G752xx series laptops have 2 physical buttons.
Luckily we can query the touchpad to see if it is a clickpad variant and
adjust the behavior accordingly.

Signed-off-by: KT Liao <kt.liao@emc.com.tw>
Tested-by: Maxime Bellengé <maxime.bellenge@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: trackpoint - add new trackpoint firmware ID
Aaron Ma [Fri, 18 Aug 2017 19:17:21 +0000 (12:17 -0700)]
Input: trackpoint - add new trackpoint firmware ID

Synaptics add new TP firmware ID: 0x2 and 0x3, for now both lower 2 bits
are indicated as TP. Change the constant to bitwise values.

This makes trackpoint to be recognized on Lenovo Carbon X1 Gen5 instead
of it being identified as "PS/2 Generic Mouse".

Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: elan_i2c - add ELAN0602 ACPI ID to support Lenovo Yoga310
KT Liao [Fri, 18 Aug 2017 23:58:15 +0000 (16:58 -0700)]
Input: elan_i2c - add ELAN0602 ACPI ID to support Lenovo Yoga310

Add ELAN0602 to the list of known ACPI IDs to enable support for ELAN
touchpads found in Lenovo Yoga310.

Signed-off-by: KT Liao <kt.liao@emc.com.tw>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: i8042 - constify pnp_device_id
Arvind Yadav [Thu, 17 Aug 2017 00:43:10 +0000 (17:43 -0700)]
Input: i8042 - constify pnp_device_id

pnp_device_id are not supposed to change at runtime. All functions
working with pnp_device_id provided by <linux/pnp.h> work with
const pnp_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: axp20x-pek - add support for AXP221 PEK
Quentin Schulz [Tue, 15 Aug 2017 05:19:42 +0000 (22:19 -0700)]
Input: axp20x-pek - add support for AXP221 PEK

The AXP221 has different values for startup time bits from the AXP20X.

Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: axp20x-pek - use driver_data of platform_device_id instead of extended attributes
Quentin Schulz [Tue, 15 Aug 2017 05:16:27 +0000 (22:16 -0700)]
Input: axp20x-pek - use driver_data of platform_device_id instead of extended attributes

To prepare an upcoming patch adding support for another PMIC that has
different startup and shutdown time, use driver_data of
platform_device_id instead of a fixed extended device attribute.

By doing so, we also remove a lot of nested structures that aren't
useful.

With this patch, a new PMIC can be easily supported by just filling
correctly its ax20x_info structure and adding a platform_device_id.

Moreover, since we get rid of extended attributes, rename
axp20x_store_ext_attr to axp20x_store_attr and axp20x_show_ext_attr to
axp20x_show_attr.

Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: ati_remote2 - constify usb_device_id
Arvind Yadav [Tue, 15 Aug 2017 05:10:55 +0000 (22:10 -0700)]
Input: ati_remote2 - constify usb_device_id

usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: sun4i-ts - constify thermal_zone_of_device_ops structures
Julia Lawall [Tue, 15 Aug 2017 05:10:11 +0000 (22:10 -0700)]
Input: sun4i-ts - constify thermal_zone_of_device_ops structures

The thermal_zone_of_device_ops structure is only passed as the fourth
argument to devm_thermal_zone_of_sensor_register, which is declared
as const.  Thus the thermal_zone_of_device_ops structure itself can
be const.

Done with the help of Coccinelle.

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: pcspkr - fix code style and error value in pcspkr_event
Munir Contractor [Tue, 15 Aug 2017 05:02:08 +0000 (22:02 -0700)]
Input: pcspkr - fix code style and error value in pcspkr_event

This patch fixes the following issues in pcspkr:

* Return -EINVAL when input arguments are not valid in pcspkr_event
  function instead of -1.
* Replace <asm/io.h> with <linux/io.h>
* Fix indentation of case blocks in switch statement
* Reduce length of line 28 to less than 80 characters

The style issues were discovered by checkpatch.pl script.

Signed-off-by: Munir Contractor <munircontractor@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: mxs-lradc - make symbol mxs_lradc_ts_irq_names static
Wei Yongjun [Mon, 14 Aug 2017 17:31:13 +0000 (10:31 -0700)]
Input: mxs-lradc - make symbol mxs_lradc_ts_irq_names static

Fixes the following sparse warning:

drivers/input/touchscreen/mxs-lradc-ts.c:33:12: warning:
 symbol 'mxs_lradc_ts_irq_names' was not declared. Should it be static?

Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
[dtor: changed to static const char * const]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: mxs-lradc - use correct error check
Pan Bian [Mon, 14 Aug 2017 17:29:13 +0000 (10:29 -0700)]
Input: mxs-lradc - use correct error check

Function devm_ioremap() will return a NULL pointer on failure. However,
in function mxs_lradc_ts_probe(), its return value is checked with
IS_ERR(), which cannot detect the exceptional case.

Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: mxs-lradc - do a NULL check on iores
Fabio Estevam [Mon, 14 Aug 2017 17:26:27 +0000 (10:26 -0700)]
Input: mxs-lradc - do a NULL check on iores

platform_get_resource() may fail, so we should better do a NULL check
and return error on failure.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: elan_i2c - Add antoher Lenovo ACPI ID for upcoming Lenovo NB
KT Liao [Tue, 15 Aug 2017 03:11:59 +0000 (20:11 -0700)]
Input: elan_i2c - Add antoher Lenovo ACPI ID for upcoming Lenovo NB

Add 2 new IDs (ELAN0609 and ELAN060B) to the list of ACPI IDs that should
be handled by the driver.

Signed-off-by: KT Liao <kt.liao@emc.com.tw>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: elan_i2c - add ELAN0608 to the ACPI table
Kai-Heng Feng [Tue, 15 Aug 2017 03:11:26 +0000 (20:11 -0700)]
Input: elan_i2c - add ELAN0608 to the ACPI table

Similar to commit 722c5ac708b4f ("Input: elan_i2c - add ELAN0605 to the
ACPI table"), ELAN0608 should be handled by elan_i2c.

This touchpad can be found in Lenovo ideapad 320-14IKB.

BugLink: https://bugs.launchpad.net/bugs/1708852
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: xpad - constify usb_device_id
Arvind Yadav [Tue, 8 Aug 2017 03:04:13 +0000 (20:04 -0700)]
Input: xpad - constify usb_device_id

usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: kbtab - constify usb_device_id
Arvind Yadav [Tue, 8 Aug 2017 02:45:14 +0000 (19:45 -0700)]
Input: kbtab - constify usb_device_id

usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: acecad - constify usb_device_idi and fix space before '[' error
Arvind Yadav [Tue, 8 Aug 2017 02:44:49 +0000 (19:44 -0700)]
Input: acecad - constify usb_device_idi and fix space before '[' error

usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.

Fix checkpatch.pl error:
ERROR: space prohibited before open square bracket '['.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: synaptics_usb - constify usb_device_id
Arvind Yadav [Tue, 8 Aug 2017 02:44:37 +0000 (19:44 -0700)]
Input: synaptics_usb - constify usb_device_id

usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: appletouch - constify usb_device_id
Arvind Yadav [Tue, 8 Aug 2017 02:44:25 +0000 (19:44 -0700)]
Input: appletouch - constify usb_device_id

usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: powermate - constify usb_device_id and fix space before '[' error
Arvind Yadav [Tue, 8 Aug 2017 02:44:10 +0000 (19:44 -0700)]
Input: powermate - constify usb_device_id and fix space before '[' error

usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.

Fix checkpatch.pl error:
ERROR: space prohibited before open square bracket '['.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: keyspan_remote - constify usb_device_id
Arvind Yadav [Tue, 8 Aug 2017 02:43:52 +0000 (19:43 -0700)]
Input: keyspan_remote - constify usb_device_id

usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: iforce - constify usb_device_id and fix space before '[' error
Arvind Yadav [Tue, 8 Aug 2017 02:43:18 +0000 (19:43 -0700)]
Input: iforce - constify usb_device_id and fix space before '[' error

usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.

Fix checkpatch.pl error:
ERROR: space prohibited before open square bracket '['.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: mousedev - fix implicit conversion warning
Nick Desaulniers [Sun, 25 Jun 2017 05:50:12 +0000 (22:50 -0700)]
Input: mousedev - fix implicit conversion warning

Clang warns:

drivers/input/mousedev.c:653:63: error: implicit conversion from 'int'
to 'signed char' changes value from 200 to -56
[-Wconstant-conversion]
  client->ps2[1] = 0x60; client->ps2[2] = 3; client->ps2[3] = 200;
                                                            ~ ^~~
As the PS2 data is really a stream of bytes, let's switch to using u8 type
for it, which silences this warning.

Signed-off-by: Nick Desaulniers <nick.desaulniers@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoARM: pxa/raumfeld: mark rotary encoder properties as __initconst
Dmitry Torokhov [Mon, 23 Jan 2017 07:46:50 +0000 (23:46 -0800)]
ARM: pxa/raumfeld: mark rotary encoder properties as __initconst

device_add_properties() performs deep copy of supplied array of properties,
which means that we can discard the original array.

Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoInput: add power key driver for Rockchip RK805 PMIC
Joseph Chen [Mon, 24 Jul 2017 22:57:12 +0000 (15:57 -0700)]
Input: add power key driver for Rockchip RK805 PMIC

This driver provides a input driver for the power key on the Rockchip RK805
PMIC.

Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
3 years agoMerge branch 'bind_unbind' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh...
Dmitry Torokhov [Mon, 24 Jul 2017 23:51:18 +0000 (16:51 -0700)]
Merge branch 'bind_unbind' of git://git./linux/kernel/git/gregkh/driver-core into next

This brings in devm_device_add_group() and friends so that we can create
driver-specific device attributes as managed resources.

3 years agoInput: axp20x-pek - switch to using devm_device_add_group()
Dmitry Torokhov [Thu, 20 Jul 2017 00:24:36 +0000 (17:24 -0700)]
Input: axp20x-pek - switch to using devm_device_add_group()

Now that we have proper managed API to create device attributes, let's
use it instead of installing a custom devm action.

Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
3 years agoInput: synaptics_rmi4 - use devm_device_add_group() for attributes in F01
Dmitry Torokhov [Thu, 20 Jul 2017 00:24:35 +0000 (17:24 -0700)]
Input: synaptics_rmi4 - use devm_device_add_group() for attributes in F01

Now that we have proper managed API to create device attributes, let's
start using it instead of the manual unwinding.

Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
3 years agoInput: gpio_keys - use devm_device_add_group() for attributes
Dmitry Torokhov [Thu, 20 Jul 2017 00:24:34 +0000 (17:24 -0700)]
Input: gpio_keys - use devm_device_add_group() for attributes

Now that we have proper managed API to create device attributes, let's
start using it instead of the manual unwinding.

Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>