Magnus Karlsson [Fri, 8 Nov 2019 19:58:10 +0000 (20:58 +0100)]
ixgbe: need_wakeup flag might not be set for Tx
The need_wakeup flag for Tx might not be set for AF_XDP sockets that
are only used to send packets. This happens if there is at least one
outstanding packet that has not been completed by the hardware and we
get that corresponding completion (which will not generate an
interrupt since interrupts are disabled in the napi poll loop) between
the time we stopped processing the Tx completions and interrupts are
enabled again. In this case, the need_wakeup flag will have been
cleared at the end of the Tx completion processing as we believe we
will get an interrupt from the outstanding completion at a later point
in time. But if this completion interrupt occurs before interrupts
are enable, we lose it and should at that point really have set the
need_wakeup flag since there are no more outstanding completions that
can generate an interrupt to continue the processing. When this
happens, user space will see a Tx queue need_wakeup of 0 and skip
issuing a syscall, which means will never get into the Tx processing
again and we have a deadlock.
This patch introduces a quick fix for this issue by just setting the
need_wakeup flag for Tx to 1 all the time. I am working on a proper
fix for this that will toggle the flag appropriately, but it is more
challenging than I anticipated and I am afraid that this patch will
not be completed before the merge window closes, therefore this easier
fix for now. This fix has a negative performance impact in the range
of 0% to 4%. Towards the higher end of the scale if you have driver
and application on the same core and issue a lot of packets, and
towards no negative impact if you use two cores, lower transmission
speeds and/or a workload that also receives packets.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Magnus Karlsson [Fri, 8 Nov 2019 19:58:09 +0000 (20:58 +0100)]
i40e: need_wakeup flag might not be set for Tx
The need_wakeup flag for Tx might not be set for AF_XDP sockets that
are only used to send packets. This happens if there is at least one
outstanding packet that has not been completed by the hardware and we
get that corresponding completion (which will not generate an
interrupt since interrupts are disabled in the napi poll loop) between
the time we stopped processing the Tx completions and interrupts are
enabled again. In this case, the need_wakeup flag will have been
cleared at the end of the Tx completion processing as we believe we
will get an interrupt from the outstanding completion at a later point
in time. But if this completion interrupt occurs before interrupts
are enable, we lose it and should at that point really have set the
need_wakeup flag since there are no more outstanding completions that
can generate an interrupt to continue the processing. When this
happens, user space will see a Tx queue need_wakeup of 0 and skip
issuing a syscall, which means will never get into the Tx processing
again and we have a deadlock.
This patch introduces a quick fix for this issue by just setting the
need_wakeup flag for Tx to 1 all the time. I am working on a proper
fix for this that will toggle the flag appropriately, but it is more
challenging than I anticipated and I am afraid that this patch will
not be completed before the merge window closes, therefore this easier
fix for now. This fix has a negative performance impact in the range
of 0% to 4%. Towards the higher end of the scale if you have driver
and application on the same core and issue a lot of packets, and
towards no negative impact if you use two cores, lower transmission
speeds and/or a workload that also receives packets.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Wed, 6 Nov 2019 17:18:23 +0000 (09:18 -0800)]
igb/igc: use ktime accessors for skb->tstamp
When implementing launch time support in the igb and igc drivers, the
skb->tstamp value is assumed to be a s64, but it's declared as a ktime_t
value.
Although ktime_t is typedef'd to s64 it wasn't always, and the kernel
provides accessors for ktime_t values.
Use the ktime_to_timespec64 and ktime_set accessors instead of directly
assuming that the variable is always an s64.
This improves portability if the code is ever moved to another kernel
version, or if the definition of ktime_t ever changes again in the
future.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Arkadiusz Kubalewski [Wed, 6 Nov 2019 14:24:04 +0000 (06:24 -0800)]
i40e: Fix for ethtool -m issue on X722 NIC
This patch contains fix for a problem with command:
'ethtool -m <dev>'
which breaks functionality of:
'ethtool <dev>'
when called on X722 NIC
Disallowed update of link phy_types on X722 NIC
Currently correct value cannot be obtained from FW
Previously wrong value returned by FW was used and was
a root cause for incorrect output of 'ethtool <dev>' command
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Nicholas Nunley [Tue, 5 Nov 2019 12:22:14 +0000 (04:22 -0800)]
iavf: initialize ITRN registers with correct values
Since commit
92418fb14750 ("i40e/i40evf: Use usec value instead of reg
value for ITR defines") the driver tracks the interrupt throttling
intervals in single usec units, although the actual ITRN registers are
programmed in 2 usec units. Most register programming flows in the driver
correctly handle the conversion, although it is currently not applied when
the registers are initialized to their default values. Most of the time
this doesn't present a problem since the default values are usually
immediately overwritten through the standard adaptive throttling mechanism,
or updated manually by the user, but if adaptive throttling is disabled and
the interval values are left alone then the incorrect value will persist.
Since the intended default interval of 50 usecs (vs. 100 usecs as
programmed) performs better for most traffic workloads, this can lead to
performance regressions.
This patch adds the correct conversion when writing the initial values to
the ITRN registers.
Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Colin Ian King [Fri, 1 Nov 2019 14:00:17 +0000 (14:00 +0000)]
ice: fix potential infinite loop because loop counter being too small
Currently the for-loop counter i is a u8 however it is being checked
against a maximum value hw->num_tx_sched_layers which is a u16. Hence
there is a potential wrap-around of counter i back to zero if
hw->num_tx_sched_layers is greater than 255. Fix this by making i
a u16.
Addresses-Coverity: ("Infinite loop")
Fixes: b36c598c999c ("ice: Updates to Tx scheduler code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Eric Dumazet [Fri, 8 Nov 2019 04:08:19 +0000 (20:08 -0800)]
net: fix data-race in neigh_event_send()
KCSAN reported the following data-race [1]
The fix will also prevent the compiler from optimizing out
the condition.
[1]
BUG: KCSAN: data-race in neigh_resolve_output / neigh_resolve_output
write to 0xffff8880a41dba78 of 8 bytes by interrupt on cpu 1:
neigh_event_send include/net/neighbour.h:443 [inline]
neigh_resolve_output+0x78/0x480 net/core/neighbour.c:1474
neigh_output include/net/neighbour.h:511 [inline]
ip_finish_output2+0x4af/0xe40 net/ipv4/ip_output.c:228
__ip_finish_output net/ipv4/ip_output.c:308 [inline]
__ip_finish_output+0x23a/0x490 net/ipv4/ip_output.c:290
ip_finish_output+0x41/0x160 net/ipv4/ip_output.c:318
NF_HOOK_COND include/linux/netfilter.h:294 [inline]
ip_output+0xdf/0x210 net/ipv4/ip_output.c:432
dst_output include/net/dst.h:436 [inline]
ip_local_out+0x74/0x90 net/ipv4/ip_output.c:125
__ip_queue_xmit+0x3a8/0xa40 net/ipv4/ip_output.c:532
ip_queue_xmit+0x45/0x60 include/net/ip.h:237
__tcp_transmit_skb+0xe81/0x1d60 net/ipv4/tcp_output.c:1169
tcp_transmit_skb net/ipv4/tcp_output.c:1185 [inline]
__tcp_retransmit_skb+0x4bd/0x15f0 net/ipv4/tcp_output.c:2976
tcp_retransmit_skb+0x36/0x1a0 net/ipv4/tcp_output.c:2999
tcp_retransmit_timer+0x719/0x16d0 net/ipv4/tcp_timer.c:515
tcp_write_timer_handler+0x42d/0x510 net/ipv4/tcp_timer.c:598
tcp_write_timer+0xd1/0xf0 net/ipv4/tcp_timer.c:618
read to 0xffff8880a41dba78 of 8 bytes by interrupt on cpu 0:
neigh_event_send include/net/neighbour.h:442 [inline]
neigh_resolve_output+0x57/0x480 net/core/neighbour.c:1474
neigh_output include/net/neighbour.h:511 [inline]
ip_finish_output2+0x4af/0xe40 net/ipv4/ip_output.c:228
__ip_finish_output net/ipv4/ip_output.c:308 [inline]
__ip_finish_output+0x23a/0x490 net/ipv4/ip_output.c:290
ip_finish_output+0x41/0x160 net/ipv4/ip_output.c:318
NF_HOOK_COND include/linux/netfilter.h:294 [inline]
ip_output+0xdf/0x210 net/ipv4/ip_output.c:432
dst_output include/net/dst.h:436 [inline]
ip_local_out+0x74/0x90 net/ipv4/ip_output.c:125
__ip_queue_xmit+0x3a8/0xa40 net/ipv4/ip_output.c:532
ip_queue_xmit+0x45/0x60 include/net/ip.h:237
__tcp_transmit_skb+0xe81/0x1d60 net/ipv4/tcp_output.c:1169
tcp_transmit_skb net/ipv4/tcp_output.c:1185 [inline]
__tcp_retransmit_skb+0x4bd/0x15f0 net/ipv4/tcp_output.c:2976
tcp_retransmit_skb+0x36/0x1a0 net/ipv4/tcp_output.c:2999
tcp_retransmit_timer+0x719/0x16d0 net/ipv4/tcp_timer.c:515
tcp_write_timer_handler+0x42d/0x510 net/ipv4/tcp_timer.c:598
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefano Garzarella [Fri, 8 Nov 2019 16:08:50 +0000 (17:08 +0100)]
vsock/virtio: fix sock refcnt holding during the shutdown
The "
42f5cda5eaf4" commit rightly set SOCK_DONE on peer shutdown,
but there is an issue if we receive the SHUTDOWN(RDWR) while the
virtio_transport_close_timeout() is scheduled.
In this case, when the timeout fires, the SOCK_DONE is already
set and the virtio_transport_close_timeout() will not call
virtio_transport_reset() and virtio_transport_do_close().
This causes that both sockets remain open and will never be released,
preventing the unloading of [virtio|vhost]_transport modules.
This patch fixes this issue, calling virtio_transport_reset() and
virtio_transport_do_close() when we receive the SHUTDOWN(RDWR)
and there is nothing left to read.
Fixes: 42f5cda5eaf4 ("vsock/virtio: set SOCK_DONE on peer shutdown")
Cc: Stephen Barber <smbarber@chromium.org>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 8 Nov 2019 19:37:24 +0000 (11:37 -0800)]
Merge tag 'mac80211-for-net-2019-11-08' of git://git./linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Three small fixes:
* we hit a failure path bug related to
ieee80211_txq_setup_flows()
* also use kvmalloc() to make that less likely
* fix a timing value shortly after boot (during
INITIAL_JIFFIES)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Sverdlin [Fri, 8 Nov 2019 10:00:44 +0000 (10:00 +0000)]
net: ethernet: octeon_mgmt: Account for second possible VLAN header
Octeon's input ring-buffer entry has 14 bits-wide size field, so to account
for second possible VLAN header max_mtu must be further reduced.
Fixes: 109cc16526c6d ("ethernet/cavium: use core min/max MTU checking")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ahmed Zaki [Thu, 31 Oct 2019 12:12:43 +0000 (06:12 -0600)]
mac80211: fix station inactive_time shortly after boot
In the first 5 minutes after boot (time of INITIAL_JIFFIES),
ieee80211_sta_last_active() returns zero if last_ack is zero. This
leads to "inactive time" showing jiffies_to_msecs(jiffies).
# iw wlan0 station get fc:ec:da:64:a6:dd
Station fc:ec:da:64:a6:dd (on wlan0)
inactive time:
4294894049 ms
.
.
connected time: 70 seconds
Fix by returning last_rx if last_ack == 0.
Signed-off-by: Ahmed Zaki <anzaki@gmail.com>
Link: https://lore.kernel.org/r/20191031121243.27694-1-anzaki@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Toke Høiland-Jørgensen [Tue, 5 Nov 2019 15:57:50 +0000 (16:57 +0100)]
net/fq_impl: Switch to kvmalloc() for memory allocation
The FQ implementation used by mac80211 allocates memory using kmalloc(),
which can fail; and Johannes reported that this actually happens in
practice.
To avoid this, switch the allocation to kvmalloc() instead; this also
brings fq_impl in line with all the FQ qdiscs.
Fixes: 557fc4a09803 ("fq: add fair queuing framework")
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20191105155750.547379-1-toke@redhat.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Tue, 5 Nov 2019 14:41:11 +0000 (15:41 +0100)]
mac80211: fix ieee80211_txq_setup_flows() failure path
If ieee80211_txq_setup_flows() fails, we don't clean up LED
state properly, leading to crashes later on, fix that.
Fixes: dc8b274f0952 ("mac80211: Move up init of TXQs")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://lore.kernel.org/r/20191105154110.1ccf7112ba5d.I0ba865792446d051867b33153be65ce6b063d98c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
David Ahern [Thu, 7 Nov 2019 18:29:52 +0000 (18:29 +0000)]
ipv4: Fix table id reference in fib_sync_down_addr
Hendrik reported routes in the main table using source address are not
removed when the address is removed. The problem is that fib_sync_down_addr
does not account for devices in the default VRF which are associated
with the main table. Fix by updating the table id reference.
Fixes: 5a56a0b3a45d ("net: Don't delete routes in different VRFs")
Reported-by: Hendrik Donner <hd@os-cillation.de>
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 7 Nov 2019 17:26:19 +0000 (09:26 -0800)]
ipv6: fixes rt6_probe() and fib6_nh->last_probe init
While looking at a syzbot KCSAN report [1], I found multiple
issues in this code :
1) fib6_nh->last_probe has an initial value of 0.
While probably okay on 64bit kernels, this causes an issue
on 32bit kernels since the time_after(jiffies, 0 + interval)
might be false ~24 days after boot (for HZ=1000)
2) The data-race found by KCSAN
I could use READ_ONCE() and WRITE_ONCE(), but we also can
take the opportunity of not piling-up too many rt6_probe_deferred()
works by using instead cmpxchg() so that only one cpu wins the race.
[1]
BUG: KCSAN: data-race in find_match / find_match
write to 0xffff8880bb7aabe8 of 8 bytes by interrupt on cpu 1:
rt6_probe net/ipv6/route.c:663 [inline]
find_match net/ipv6/route.c:757 [inline]
find_match+0x5bd/0x790 net/ipv6/route.c:733
__find_rr_leaf+0xe3/0x780 net/ipv6/route.c:831
find_rr_leaf net/ipv6/route.c:852 [inline]
rt6_select net/ipv6/route.c:896 [inline]
fib6_table_lookup+0x383/0x650 net/ipv6/route.c:2164
ip6_pol_route+0xee/0x5c0 net/ipv6/route.c:2200
ip6_pol_route_output+0x48/0x60 net/ipv6/route.c:2452
fib6_rule_lookup+0x3d6/0x470 net/ipv6/fib6_rules.c:117
ip6_route_output_flags_noref+0x16b/0x230 net/ipv6/route.c:2484
ip6_route_output_flags+0x50/0x1a0 net/ipv6/route.c:2497
ip6_dst_lookup_tail+0x25d/0xc30 net/ipv6/ip6_output.c:1049
ip6_dst_lookup_flow+0x68/0x120 net/ipv6/ip6_output.c:1150
inet6_csk_route_socket+0x2f7/0x420 net/ipv6/inet6_connection_sock.c:106
inet6_csk_xmit+0x91/0x1f0 net/ipv6/inet6_connection_sock.c:121
__tcp_transmit_skb+0xe81/0x1d60 net/ipv4/tcp_output.c:1169
tcp_transmit_skb net/ipv4/tcp_output.c:1185 [inline]
tcp_xmit_probe_skb+0x19b/0x1d0 net/ipv4/tcp_output.c:3735
read to 0xffff8880bb7aabe8 of 8 bytes by interrupt on cpu 0:
rt6_probe net/ipv6/route.c:657 [inline]
find_match net/ipv6/route.c:757 [inline]
find_match+0x521/0x790 net/ipv6/route.c:733
__find_rr_leaf+0xe3/0x780 net/ipv6/route.c:831
find_rr_leaf net/ipv6/route.c:852 [inline]
rt6_select net/ipv6/route.c:896 [inline]
fib6_table_lookup+0x383/0x650 net/ipv6/route.c:2164
ip6_pol_route+0xee/0x5c0 net/ipv6/route.c:2200
ip6_pol_route_output+0x48/0x60 net/ipv6/route.c:2452
fib6_rule_lookup+0x3d6/0x470 net/ipv6/fib6_rules.c:117
ip6_route_output_flags_noref+0x16b/0x230 net/ipv6/route.c:2484
ip6_route_output_flags+0x50/0x1a0 net/ipv6/route.c:2497
ip6_dst_lookup_tail+0x25d/0xc30 net/ipv6/ip6_output.c:1049
ip6_dst_lookup_flow+0x68/0x120 net/ipv6/ip6_output.c:1150
inet6_csk_route_socket+0x2f7/0x420 net/ipv6/inet6_connection_sock.c:106
inet6_csk_xmit+0x91/0x1f0 net/ipv6/inet6_connection_sock.c:121
__tcp_transmit_skb+0xe81/0x1d60 net/ipv4/tcp_output.c:1169
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 18894 Comm: udevd Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: cc3a86c802f0 ("ipv6: Change rt6_probe to take a fib6_nh")
Fixes: f547fac624be ("ipv6: rate-limit probes for neighbourless routes")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Salil Mehta [Thu, 7 Nov 2019 17:09:53 +0000 (17:09 +0000)]
net: hns: Fix the stray netpoll locks causing deadlock in NAPI path
This patch fixes the problem of the spin locks, originally
meant for the netpoll path of hns driver, causing deadlock in
the normal NAPI poll path. The issue happened due to the presence
of the stray leftover spin lock code related to the netpoll,
whose support was earlier removed from the HNS[1], got activated
due to enabling of NET_POLL_CONTROLLER switch.
Earlier background:
The netpoll handling code originally had this bug(as identified
by Marc Zyngier[2]) of wrong spin lock API being used which did
not disable the interrupts and hence could cause locking issues.
i.e. if the lock were first acquired in context to thread like
'ip' util and this lock if ever got later acquired again in
context to the interrupt context like TX/RX (Interrupts could
always pre-empt the lock holding task and acquire the lock again)
and hence could cause deadlock.
Proposed Solution:
1. If the netpoll was enabled in the HNS driver, which is not
right now, we could have simply used spin_[un]lock_irqsave()
2. But as netpoll is disabled, therefore, it is best to get rid
of the existing locks and stray code for now. This should
solve the problem reported by Marc.
[1] https://git.kernel.org/torvalds/c/
4bd2c03be7
[2] https://patchwork.ozlabs.org/patch/
1189139/
Fixes: 4bd2c03be707 ("net: hns: remove ndo_poll_controller")
Cc: lipeng <lipeng321@huawei.com>
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: David S. Miller <davem@davemloft.net>
Reported-by: Marc Zyngier <maz@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Tested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aleksander Morgado [Thu, 7 Nov 2019 10:57:01 +0000 (11:57 +0100)]
net: usb: qmi_wwan: add support for DW5821e with eSIM support
Exactly same layout as the default DW5821e module, just a different
vid/pid.
The QMI interface is exposed in USB configuration #1:
P: Vendor=413c ProdID=81e0 Rev=03.18
S: Manufacturer=Dell Inc.
S: Product=DW5821e-eSIM Snapdragon X20 LTE
S: SerialNumber=
0123456789ABCDEF
C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#=0x1 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=usbhid
I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: David S. Miller <davem@davemloft.net>
Oliver Neukum [Thu, 7 Nov 2019 08:48:01 +0000 (09:48 +0100)]
CDC-NCM: handle incomplete transfer of MTU
A malicious device may give half an answer when asked
for its MTU. The driver will proceed after this with
a garbage MTU. Anything but a complete answer must be treated
as an error.
V2: used sizeof as request by Alexander
Reported-and-tested-by: syzbot+0631d878823ce2411636@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pan Bian [Thu, 7 Nov 2019 06:29:50 +0000 (14:29 +0800)]
nfc: netlink: fix double device reference drop
The function nfc_put_device(dev) is called twice to drop the reference
to dev when there is no associated local llcp. Remove one of them to fix
the bug.
Fixes: 52feb444a903 ("NFC: Extend netlink interface for LTO, RW, and MIUX parameters support")
Fixes: d9b8d8e19b07 ("NFC: llcp: Service Name Lookup netlink interface")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pan Bian [Thu, 7 Nov 2019 01:33:20 +0000 (09:33 +0800)]
NFC: st21nfca: fix double free
The variable nfcid_skb is not changed in the callee nfc_hci_get_param()
if error occurs. Consequently, the freed variable nfcid_skb will be
freed again, resulting in a double free bug. Set nfcid_skb to NULL after
releasing it to fix the bug.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Thu, 7 Nov 2019 01:30:19 +0000 (09:30 +0800)]
net: hns3: add compatible handling for command HCLGE_OPC_PF_RST_DONE
Since old firmware does not support HCLGE_OPC_PF_RST_DONE, it will
return -EOPNOTSUPP to the driver when received this command. So
for this case, it should just print a warning and return success
to the caller.
Fixes: 72e2fb07997c ("net: hns3: clear reset interrupt status in hclge_irq_handle()")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 7 Nov 2019 05:39:48 +0000 (21:39 -0800)]
Merge tag 'mlx5-fixes-2019-11-06' of git://git./linux/kernel/git/saeed/linux
Saeed Mahamees says:
====================
Mellanox, mlx5 fixes 2019-11-06
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
No -stable this time.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Wed, 6 Nov 2019 20:51:31 +0000 (21:51 +0100)]
r8169: fix page read in r8168g_mdio_read
Functions like phy_modify_paged() read the current page, on Realtek
PHY's this means reading the value of register 0x1f. Add special
handling for reading this register, similar to what we do already
in r8168g_mdio_write(). Currently we read a random value that by
chance seems to be 0 always.
Fixes: a2928d28643e ("r8169: use paged versions of phylib MDIO access functions")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 7 Nov 2019 05:22:56 +0000 (21:22 -0800)]
Merge branch 'stmmac-fixes'
Jose Abreu says:
====================
net: stmmac: Fixes for -net
Misc fixes for stmmac.
Patch 1/11 and 2/11, use the correct variable type for bitrev32() calls.
Patch 3/11, fixes the random failures the we were seing when running selftests.
Patch 4/11, prevents a crash that can occur when receiving AVB packets and with
SPH feature enabled on XGMAC.
Patch 5/11, fixes the correct settings for CBS on XGMAC.
Patch 6/11, corrects the interpretation of AVB feature on XGMAC.
Patch 7/11, disables Flow Control for AVB enabled queues on XGMAC.
Patch 8/11, disables MMC interrupts on XGMAC, preventing a storm of interrupts.
Patch 9/11, fixes the number of packets that were being taken into account in
the RX path cleaning function.
Patch 10/11, fixes an incorrect descriptor setting that could cause IP
misbehavior.
Patch 11/11, fixes the IOC generation mechanism when multiple descriptors
are used.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Wed, 6 Nov 2019 15:03:05 +0000 (16:03 +0100)]
net: stmmac: Fix the TX IOC in xmit path
IOC bit must be only set in the last descriptor. Move the logic up a
little bit to make sure it's set in the correct descriptor.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Wed, 6 Nov 2019 15:03:04 +0000 (16:03 +0100)]
net: stmmac: Fix TSO descriptor with Enhanced Addressing
When using addressing > 32 bits the TSO first descriptor only has the
header so we can't set the payload field for this descriptor. Let's
reset the variable so that buffer 2 value is zero.
Fixes: a993db88d17d ("net: stmmac: Enable support for > 32 Bits addressing in XGMAC")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Wed, 6 Nov 2019 15:03:03 +0000 (16:03 +0100)]
net: stmmac: Fix the packet count in stmmac_rx()
Currently, stmmac_rx() is counting the number of descriptors but it
should count the number of packets as specified by the NAPI limit.
Fix this.
Fixes: ec222003bd94 ("net: stmmac: Prepare to add Split Header support")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Wed, 6 Nov 2019 15:03:02 +0000 (16:03 +0100)]
net: stmmac: xgmac: Disable MMC interrupts by default
MMC interrupts were being enabled, which is not what we want because it
will lead to a storm of interrupts that are not handled at all. Fix it
by disabling all MMC interrupts for XGMAC.
Fixes: b6cdf09f51c2 ("net: stmmac: xgmac: Implement MMC counters")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Wed, 6 Nov 2019 15:03:01 +0000 (16:03 +0100)]
net: stmmac: xgmac: Disable Flow Control when 1 or more queues are in AV
When in AVB mode we need to disable flow control to prevent MAC from
pausing in TX side.
Fixes: ec6ea8e3eee9 ("net: stmmac: Add CBS support in XGMAC2")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Wed, 6 Nov 2019 15:03:00 +0000 (16:03 +0100)]
net: stmmac: xgmac: Fix AV Feature detection
Fix incorrect precedence of operators. For reference: AV implies AV
Feature but RAV implies only RX side AV Feature. As we want full AV
features we need to check RAV.
Fixes: c2b69474d63b ("net: stmmac: xgmac: Correct RAVSEL field interpretation")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Wed, 6 Nov 2019 15:02:59 +0000 (16:02 +0100)]
net: stmmac: xgmac: Fix TSA selection
When we change between Transmission Scheduling Algorithms, we need to
clear previous values so that the new chosen algorithm is correctly
selected.
Fixes: ec6ea8e3eee9 ("net: stmmac: Add CBS support in XGMAC2")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Wed, 6 Nov 2019 15:02:58 +0000 (16:02 +0100)]
net: stmmac: xgmac: Only get SPH header len if available
Split Header length is only available when L34T == 0. Fix this by
correctly checking if L34T is zero before trying to get Header length.
Fixes: 67afd6d1cfdf ("net: stmmac: Add Split Header support and enable it in XGMAC cores")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Wed, 6 Nov 2019 15:02:57 +0000 (16:02 +0100)]
net: stmmac: selftests: Prevent false positives in filter tests
In L2 tests that filter packets by destination MAC address we need to
prevent false positives that can occur if we add an address that
collides with the existing ones.
To fix this, lets manually check if the new address to be added is
already present in the NIC and use a different one if so. For Hash
filtering this also envolves converting the address to the hash.
Fixes: 091810dbded9 ("net: stmmac: Introduce selftests support")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Wed, 6 Nov 2019 15:02:56 +0000 (16:02 +0100)]
net: stmmac: xgmac: bitrev32 returns u32
The bitrev32 function returns an u32 var, not an int. Fix it.
Fixes: 0efedbf11f07 ("net: stmmac: xgmac: Fix XGMAC selftests")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Wed, 6 Nov 2019 15:02:55 +0000 (16:02 +0100)]
net: stmmac: gmac4: bitrev32 returns u32
The bitrev32 function returns an u32 var, not an int. Fix it.
Fixes: 477286b53f55 ("stmmac: add GMAC4 core support")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 7 Nov 2019 05:16:55 +0000 (21:16 -0800)]
Merge git://git./pub/scm/linux/kernel/git/pablo/nf
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Missing register size validation in bitwise and cmp offloads.
2) Fix error code in ip_set_sockfn_get() when copy_to_user() fails,
from Dan Carpenter.
3) Oneliner to copy MAC address in IPv6 hash:ip,mac sets, from
Stefano Brivio.
4) Missing policy validation in ipset with NL_VALIDATE_STRICT,
from Jozsef Kadlecsik.
5) Fix unaligned access to private data area of nf_tables instructions,
from Lukas Wunner.
6) Relax check for object updates, reported as a regression by
Eric Garver, patch from Fernando Fernandez Mancera.
7) Crash on ebtables dnat extension when used from the output path.
From Florian Westphal.
8) Fix bogus EOPNOTSUPP when updating basechain flags.
9) Fix bogus EBUSY when updating a basechain that is already offloaded.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Wed, 6 Nov 2019 09:49:57 +0000 (10:49 +0100)]
net/smc: fix ethernet interface refcounting
If a pnet table entry is to be added mentioning a valid ethernet
interface, but an invalid infiniband or ISM device, the dev_put()
operation for the ethernet interface is called twice, resulting
in a negative refcount for the ethernet interface, which disables
removal of such a network interface.
This patch removes one of the dev_put() calls.
Fixes: 890a2cb4a966 ("net/smc: rework pnet table")
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 7 Nov 2019 01:33:32 +0000 (17:33 -0800)]
Merge branch 'net-tls-add-a-TX-lock'
Jakub Kicinski says:
====================
net/tls: add a TX lock
Some time ago Pooja and Mallesham started reporting crashes with
an async accelerator. After trying to poke the existing logic into
shape I came to the conclusion that it can't be trusted, and to
preserve our sanity we should just add a lock around the TX side.
First patch removes the sk_write_pending checks from the write
space callbacks. Those don't seem to have a logical justification.
Patch 2 adds the TX lock and patch 3 associated test (which should
hang with current net).
Mallesham reports that even with these fixes applied the async
accelerator workload still occasionally hangs waiting for socket
memory. I suspect that's strictly related to the way async crypto
is integrated in TLS, so I think we should get these into net or
net-next and move from there.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 5 Nov 2019 22:24:36 +0000 (14:24 -0800)]
selftests/tls: add test for concurrent recv and send
Add a test which spawns 16 threads and performs concurrent
send and recv calls on the same socket.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 5 Nov 2019 22:24:35 +0000 (14:24 -0800)]
net/tls: add a TX lock
TLS TX needs to release and re-acquire the socket lock if send buffer
fills up.
TLS SW TX path currently depends on only allowing one thread to enter
the function by the abuse of sk_write_pending. If another writer is
already waiting for memory no new ones are allowed in.
This has two problems:
- writers don't wake other threads up when they leave the kernel;
meaning that this scheme works for single extra thread (second
application thread or delayed work) because memory becoming
available will send a wake up request, but as Mallesham and
Pooja report with larger number of threads it leads to threads
being put to sleep indefinitely;
- the delayed work does not get _scheduled_ but it may _run_ when
other writers are present leading to crashes as writers don't
expect state to change under their feet (same records get pushed
and freed multiple times); it's hard to reliably bail from the
work, however, because the mere presence of a writer does not
guarantee that the writer will push pending records before exiting.
Ensuring wakeups always happen will make the code basically open
code a mutex. Just use a mutex.
The TLS HW TX path does not have any locking (not even the
sk_write_pending hack), yet it uses a per-socket sg_tx_data
array to push records.
Fixes: a42055e8d2c3 ("net/tls: Add support for async encryption of records for performance")
Reported-by: Mallesham Jatharakonda <mallesh537@gmail.com>
Reported-by: Pooja Trivedi <poojatrivedi@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 5 Nov 2019 22:24:34 +0000 (14:24 -0800)]
net/tls: don't pay attention to sk_write_pending when pushing partial records
sk_write_pending being not zero does not guarantee that partial
record will be pushed. If the thread waiting for memory times out
the pending record may get stuck.
In case of tls_device there is no path where parial record is
set and writer present in the first place. Partial record is
set only in tls_push_sg() and tls_push_sg() will return an
error immediately. All tls_device callers of tls_push_sg()
will return (and not wait for memory) if it failed.
Fixes: a42055e8d2c3 ("net/tls: Add support for async encryption of records for performance")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Tue, 5 Nov 2019 22:01:40 +0000 (00:01 +0200)]
net: mscc: ocelot: fix __ocelot_rmw_ix prototype
The "read-modify-write register index" function is declared with a
confusing prototype: the "mask" and "reg" arguments are swapped.
Fortunately, this does not affect callers so far. Both arguments are
u32, and the wrapper macros (ocelot_rmw_ix etc) have the arguments in
the correct order (the one from ocelot_io.c).
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 6 Nov 2019 23:16:17 +0000 (15:16 -0800)]
Merge branch 'Bonding-fixes-for-Ocelot-switch'
Vladimir Oltean says:
====================
Bonding fixes for Ocelot switch
This series fixes 2 issues with bonding in a system that integrates the
ocelot driver, but the ports that are bonded do not actually belong to
ocelot.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Claudiu Manoil [Tue, 5 Nov 2019 21:50:14 +0000 (23:50 +0200)]
net: mscc: ocelot: fix NULL pointer on LAG slave removal
lag_upper_info may be NULL on slave removal.
Fixes: dc96ee3730fc ("net: mscc: ocelot: add bonding support")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Claudiu Manoil [Tue, 5 Nov 2019 21:50:13 +0000 (23:50 +0200)]
net: mscc: ocelot: don't handle netdev events for other netdevs
The check that the event is actually for this device should be moved
from the "port" handler to the net device handler.
Otherwise the port handler will deny bonding configuration for other
net devices in the same system (like enetc in the LS1028A) that don't
have the lag_upper_info->tx_type restriction that ocelot has.
Fixes: dc96ee3730fc ("net: mscc: ocelot: add bonding support")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmytro Linkin [Tue, 29 Oct 2019 09:44:24 +0000 (11:44 +0200)]
net/mlx5e: Use correct enum to determine uplink port
For vlan push action, if eswitch flow source capability is enabled, flow
source value compared with MLX5_VPORT_UPLINK enum, to determine uplink
port. This lead to syndrome in dmesg if try to add vlan push action.
For example:
$ tc filter add dev vxlan0 ingress protocol ip prio 1 flower \
enc_dst_port 4789 \
action tunnel_key unset pipe \
action vlan push id 20 pipe \
action mirred egress redirect dev ens1f0_0
$ dmesg
...
[ 2456.883693] mlx5_core 0000:82:00.0: mlx5_cmd_check:756:(pid 5273): SET_FLOW_TABLE_ENTRY(0x936) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0xa9c090)
Use the correct enum value MLX5_FLOW_CONTEXT_FLOW_SOURCE_UPLINK.
Fixes: bb204dcf39fe ("net/mlx5e: Determine source port properly for vlan push action")
Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Alex Vesker [Tue, 29 Oct 2019 16:18:10 +0000 (18:18 +0200)]
net/mlx5: DR, Fix memory leak during rule creation
During rule creation hw_ste_arr was not freed.
Fixes: 41d07074154c ("net/mlx5: DR, Expose steering rule functionality")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Alex Vesker [Tue, 29 Oct 2019 11:28:17 +0000 (13:28 +0200)]
net/mlx5: DR, Fix memory leak in modify action destroy
The rewrite data was no freed.
Fixes: 9db810ed2d37 ("net/mlx5: DR, Expose steering action functionality")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Roi Dayan [Mon, 28 Oct 2019 17:13:58 +0000 (19:13 +0200)]
net/mlx5e: Fix eswitch debug print of max fdb flow
The value is already the calculation so remove the log prefix.
Fixes: e52c28024008 ("net/mlx5: E-Switch, Add chains and priorities")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
David S. Miller [Wed, 6 Nov 2019 18:46:22 +0000 (10:46 -0800)]
Merge branch 'net-bcmgenet-restore-internal-EPHY-support'
Doug Berger says:
====================
net: bcmgenet: restore internal EPHY support (part 2)
This is a follow up to my previous submission (see [1]).
The first commit provides what is intended to be a complete solution
for the issues that can result from insufficient clocking of the MAC
during reset of its state machines. It should be backported to the
stable releases.
It is intended to replace the partial solution of commit
1f515486275a
("net: bcmgenet: soft reset 40nm EPHYs before MAC init") which is
reverted by the second commit of this series and should not be back-
ported as noted in [2].
The third commit corrects a timing hazard with a polled PHY that can
occur when the MAC resumes and also when a v3 internal EPHY is reset
by the change in commit
25382b991d25 ("net: bcmgenet: reset 40nm EPHY
on energy detect"). It is expected that commit
25382b991d25 be back-
ported to stable first before backporting this commit.
[1] https://lkml.org/lkml/2019/10/16/1706
[2] https://lkml.org/lkml/2019/10/31/749
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Doug Berger [Tue, 5 Nov 2019 19:07:26 +0000 (11:07 -0800)]
net: bcmgenet: reapply manual settings to the PHY
The phy_init_hw() function may reset the PHY to a configuration
that does not match manual network settings stored in the phydev
structure. If the phy state machine is polled rather than event
driven this can create a timing hazard where the phy state machine
might alter the settings stored in the phydev structure from the
value read from the BMCR.
This commit follows invocations of phy_init_hw() by the bcmgenet
driver with invocations of the genphy_config_aneg() function to
ensure that the BMCR is written to match the settings held in the
phydev structure. This prevents the risk of manual settings being
accidentally altered.
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Doug Berger [Tue, 5 Nov 2019 19:07:25 +0000 (11:07 -0800)]
Revert "net: bcmgenet: soft reset 40nm EPHYs before MAC init"
This reverts commit
1f515486275a08a17a2c806b844cca18f7de5b34.
This commit improved the chances of the umac resetting cleanly by
ensuring that the PHY was restored to its normal operation prior
to resetting the umac. However, there were still cases when the
PHY might not be driving a Tx clock to the umac during this window
(e.g. when the PHY detects no link).
The previous commit now ensures that the unimac receives clocks
from the MAC during its reset window so this commit is no longer
needed. This commit also has an unintended negative impact on the
MDIO performance of the UniMAC MDIO interface because it is used
before the MDIO interrupts are reenabled, so it should be removed.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Doug Berger [Tue, 5 Nov 2019 19:07:24 +0000 (11:07 -0800)]
net: bcmgenet: use RGMII loopback for MAC reset
As noted in commit
28c2d1a7a0bf ("net: bcmgenet: enable loopback
during UniMAC sw_reset") the UniMAC must be clocked while sw_reset
is asserted for its state machines to reset cleanly.
The transmit and receive clocks used by the UniMAC are derived from
the signals used on its PHY interface. The bcmgenet MAC can be
configured to work with different PHY interfaces including MII,
GMII, RGMII, and Reverse MII on internal and external interfaces.
Unfortunately for the UniMAC, when configured for MII the Tx clock
is always driven from the PHY which places it outside of the direct
control of the MAC.
The earlier commit enabled a local loopback mode within the UniMAC
so that the receive clock would be derived from the transmit clock
which addressed the observed issue with an external GPHY disabling
it's Rx clock. However, when a Tx clock is not available this
loopback is insufficient.
This commit implements a workaround that leverages the fact that
the MAC can reliably generate all of its necessary clocking by
enterring the external GPHY RGMII interface mode with the UniMAC in
local loopback during the sw_reset interval. Unfortunately, this
has the undesirable side efect of the RGMII GTXCLK signal being
driven during the same window.
In most configurations this is a benign side effect as the signal
is either not routed to a pin or is already expected to drive the
pin. The one exception is when an external MII PHY is expected to
drive the same pin with its TX_CLK output creating output driver
contention.
This commit exploits the IEEE 802.3 clause 22 standard defined
isolate mode to force an external MII PHY to present a high
impedance on its TX_CLK output during the window to prevent any
contention at the pin.
The MII interface is used internally with the 40nm internal EPHY
which agressively disables its clocks for power savings leading to
incomplete resets of the UniMAC and many instabilities observed
over the years. The workaround of this commit is expected to put
an end to those problems.
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tariq Toukan [Tue, 5 Nov 2019 12:13:48 +0000 (14:13 +0200)]
Documentation: TLS: Add missing counter description
Add TLS TX counter description for the handshake retransmitted
packets that triggers the resync procedure then skip it, going
into the regular transmit flow.
Fixes: 46a3ea98074e ("net/mlx5e: kTLS, Enhance TX resync flow")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pan Bian [Tue, 5 Nov 2019 08:34:07 +0000 (16:34 +0800)]
NFC: fdp: fix incorrect free object
The address of fw_vsc_cfg is on stack. Releasing it with devm_kfree() is
incorrect, which may result in a system crash or other security impacts.
The expected object to free is *fw_vsc_cfg.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 5 Nov 2019 05:38:43 +0000 (21:38 -0800)]
net: prevent load/store tearing on sk->sk_stamp
Add a couple of READ_ONCE() and WRITE_ONCE() to prevent
load-tearing and store-tearing in sock_read_timestamp()
and sock_write_timestamp()
This might prevent another KCSAN report.
Fixes: 3a0ed3e96197 ("sock: Make sock->sk_stamp thread-safe")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Deepa Dinamani <deepa.kernel@gmail.com>
Acked-by: Deepa Dinamani <deepa.kernel@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sean Tranchetti [Tue, 5 Nov 2019 00:54:22 +0000 (17:54 -0700)]
net: qualcomm: rmnet: Fix potential UAF when unregistering
During the exit/unregistration process of the RmNet driver, the function
rmnet_unregister_real_device() is called to handle freeing the driver's
internal state and removing the RX handler on the underlying physical
device. However, the order of operations this function performs is wrong
and can lead to a use after free of the rmnet_port structure.
Before calling netdev_rx_handler_unregister(), this port structure is
freed with kfree(). If packets are received on any RmNet devices before
synchronize_net() completes, they will attempt to use this already-freed
port structure when processing the packet. As such, before cleaning up any
other internal state, the RX handler must be unregistered in order to
guarantee that no further packets will arrive on the device.
Fixes: ceed73a2cf4a ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 4 Nov 2019 23:36:57 +0000 (15:36 -0800)]
net/tls: fix sk_msg trim on fallback to copy mode
sk_msg_trim() tries to only update curr pointer if it falls into
the trimmed region. The logic, however, does not take into the
account pointer wrapping that sk_msg_iter_var_prev() does nor
(as John points out) the fact that msg->sg is a ring buffer.
This means that when the message was trimmed completely, the new
curr pointer would have the value of MAX_MSG_FRAGS - 1, which is
neither smaller than any other value, nor would it actually be
correct.
Special case the trimming to 0 length a little bit and rework
the comparison between curr and end to take into account wrapping.
This bug caused the TLS code to not copy all of the message, if
zero copy filled in fewer sg entries than memcopy would need.
Big thanks to Alexander Potapenko for the non-KMSAN reproducer.
v2:
- take into account that msg->sg is a ring buffer (John).
Link: https://lore.kernel.org/netdev/20191030160542.30295-1-jakub.kicinski@netronome.com/
Fixes: d829e9c4112b ("tls: convert to generic sk_msg interface")
Reported-by: syzbot+f8495bff23a879a6d0bd@syzkaller.appspotmail.com
Reported-by: syzbot+6f50c99e8f6194bf363f@syzkaller.appspotmail.com
Co-developed-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dotan Barak [Sun, 3 Nov 2019 09:11:35 +0000 (11:11 +0200)]
mlx4_core: fix wrong comment about the reason of subtract one from the max_cqes
The reason for the pre-allocation of one CQE is to enable resizing of
the CQ.
Fix comment accordingly.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.com>
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Sun, 3 Nov 2019 03:17:39 +0000 (20:17 -0700)]
net: dsa: bcm_sf2: Fix driver removal
With the DSA core doing the call to dsa_port_disable() we do not need to
do that within the driver itself. This could cause an use after free
since past dsa_unregister_switch() we should not be accessing any
dsa_switch internal structures.
Fixes: 0394a63acfe2 ("net: dsa: enable and disable all ports")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John Hurley [Sat, 2 Nov 2019 14:17:47 +0000 (14:17 +0000)]
net: sched: prevent duplicate flower rules from tcf_proto destroy race
When a new filter is added to cls_api, the function
tcf_chain_tp_insert_unique() looks up the protocol/priority/chain to
determine if the tcf_proto is duplicated in the chain's hashtable. It then
creates a new entry or continues with an existing one. In cls_flower, this
allows the function fl_ht_insert_unque to determine if a filter is a
duplicate and reject appropriately, meaning that the duplicate will not be
passed to drivers via the offload hooks. However, when a tcf_proto is
destroyed it is removed from its chain before a hardware remove hook is
hit. This can lead to a race whereby the driver has not received the
remove message but duplicate flows can be accepted. This, in turn, can
lead to the offload driver receiving incorrect duplicate flows and out of
order add/delete messages.
Prevent duplicates by utilising an approach suggested by Vlad Buslov. A
hash table per block stores each unique chain/protocol/prio being
destroyed. This entry is only removed when the full destroy (and hardware
offload) has completed. If a new flow is being added with the same
identiers as a tc_proto being detroyed, then the add request is replayed
until the destroy is complete.
Fixes: 8b64678e0af8 ("net: sched: refactor tp insert/delete for concurrent execution")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reported-by: Louis Peens <louis.peens@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nishad Kamdar [Sat, 2 Nov 2019 11:44:42 +0000 (17:14 +0530)]
net: hns3: Use the correct style for SPDX License Identifier
This patch corrects the SPDX License Identifier style in
header files related to Hisilicon network devices. For C header files
Documentation/process/license-rules.rst mandates C-like comments
(opposed to C source files where C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jay Vosburgh [Sat, 2 Nov 2019 04:56:42 +0000 (21:56 -0700)]
bonding: fix state transition issue in link monitoring
Since
de77ecd4ef02 ("bonding: improve link-status update in
mii-monitoring"), the bonding driver has utilized two separate variables
to indicate the next link state a particular slave should transition to.
Each is used to communicate to a different portion of the link state
change commit logic; one to the bond_miimon_commit function itself, and
another to the state transition logic.
Unfortunately, the two variables can become unsynchronized,
resulting in incorrect link state transitions within bonding. This can
cause slaves to become stuck in an incorrect link state until a
subsequent carrier state transition.
The issue occurs when a special case in bond_slave_netdev_event
sets slave->link directly to BOND_LINK_FAIL. On the next pass through
bond_miimon_inspect after the slave goes carrier up, the BOND_LINK_FAIL
case will set the proposed next state (link_new_state) to BOND_LINK_UP,
but the new_link to BOND_LINK_DOWN. The setting of the final link state
from new_link comes after that from link_new_state, and so the slave
will end up incorrectly in _DOWN state.
Resolve this by combining the two variables into one.
Reported-by: Aleksei Zakharov <zakharov.a.g@yandex.ru>
Reported-by: Sha Zhang <zhangsha.zhang@huawei.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Fixes: de77ecd4ef02 ("bonding: improve link-status update in mii-monitoring")
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 6 Nov 2019 01:38:21 +0000 (17:38 -0800)]
Merge git://git./pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2019-11-02
The following pull-request contains BPF updates for your *net* tree.
We've added 6 non-merge commits during the last 6 day(s) which contain
a total of 8 files changed, 35 insertions(+), 9 deletions(-).
The main changes are:
1) Fix ppc BPF JIT's tail call implementation by performing a second pass
to gather a stable JIT context before opcode emission, from Eric Dumazet.
2) Fix build of BPF samples sys_perf_event_open() usage to compiled out
unavailable test_attr__{enabled,open} checks. Also fix potential overflows
in bpf_map_{area_alloc,charge_init} on 32 bit archs, from Björn Töpel.
3) Fix narrow loads of bpf_sysctl context fields with offset > 0 on big endian
archs like s390x and also improve the test coverage, from Ilya Leoshkevich.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Khoronzhuk [Fri, 1 Nov 2019 23:28:28 +0000 (01:28 +0200)]
taprio: fix panic while hw offload sched list swap
Don't swap oper and admin schedules too early, it's not correct and
causes crash.
Steps to reproduce:
1)
tc qdisc replace dev eth0 parent root handle 100 taprio \
num_tc 3 \
map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 \
queues 1@0 1@1 1@2 \
base-time $SOME_BASE_TIME \
sched-entry S 01 80000 \
sched-entry S 02 15000 \
sched-entry S 04 40000 \
flags 2
2)
tc qdisc replace dev eth0 parent root handle 100 taprio \
base-time $SOME_BASE_TIME \
sched-entry S 01 90000 \
sched-entry S 02 20000 \
sched-entry S 04 40000 \
flags 2
3)
tc qdisc replace dev eth0 parent root handle 100 taprio \
base-time $SOME_BASE_TIME \
sched-entry S 01 150000 \
sched-entry S 02 200000 \
sched-entry S 04 40000 \
flags 2
Do 2 3 2 .. steps more times if not happens and observe:
[ 305.832319] Unable to handle kernel write to read-only memory at
virtual address
ffff0000087ce7f0
[ 305.910887] CPU: 0 PID: 0 Comm: swapper/0 Not tainted
[ 305.919306] Hardware name: Texas Instruments AM654 Base Board (DT)
[...]
[ 306.017119] x1 :
ffff800848031d88 x0 :
ffff800848031d80
[ 306.022422] Call trace:
[ 306.024866] taprio_free_sched_cb+0x4c/0x98
[ 306.029040] rcu_process_callbacks+0x25c/0x410
[ 306.033476] __do_softirq+0x10c/0x208
[ 306.037132] irq_exit+0xb8/0xc8
[ 306.040267] __handle_domain_irq+0x64/0xb8
[ 306.044352] gic_handle_irq+0x7c/0x178
[ 306.048092] el1_irq+0xb0/0x128
[ 306.051227] arch_cpu_idle+0x10/0x18
[ 306.054795] do_idle+0x120/0x138
[ 306.058015] cpu_startup_entry+0x20/0x28
[ 306.061931] rest_init+0xcc/0xd8
[ 306.065154] start_kernel+0x3bc/0x3e4
[ 306.068810] Code:
f2fbd5b7 f2fbd5b6 d503201f f9400422 (
f9000662)
[ 306.074900] ---[ end trace
96c8e2284a9d9d6e ]---
[ 306.079507] Kernel panic - not syncing: Fatal exception in interrupt
[ 306.085847] SMP: stopping secondary CPUs
[ 306.089765] Kernel Offset: disabled
Try to explain one of the possible crash cases:
The "real" admin list is assigned when admin_sched is set to
new_admin, it happens after "swap", that assigns to oper_sched NULL.
Thus if call qdisc show it can crash.
Farther, next second time, when sched list is updated, the admin_sched
is not NULL and becomes the oper_sched, previous oper_sched was NULL so
just skipped. But then admin_sched is assigned new_admin, but schedules
to free previous assigned admin_sched (that already became oper_sched).
Farther, next third time, when sched list is updated,
while one more swap, oper_sched is not null, but it was happy to be
freed already (while prev. admin update), so while try to free
oper_sched the kernel panic happens at taprio_free_sched_cb().
So, move the "swap emulation" where it should be according to function
comment from code.
Fixes: 9c66d15646760e ("taprio: Add support for hardware offloading")
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 5 Nov 2019 21:29:18 +0000 (13:29 -0800)]
Merge tag 'linux-can-fixes-for-5.4-
20191105' of git://git./linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2019-11-05
this is a pull request of 33 patches for net/master.
In the first patch Wen Yang's patch adds a missing of_node_put() to CAN device
infrastructure.
Navid Emamdoost's patch for the gs_usb driver fixes a memory leak in the
gs_can_open() error path.
Johan Hovold provides two patches, one for the mcba_usb, the other for the
usb_8dev driver. Both fix a use-after-free after USB-disconnect.
Joakim Zhang's patch improves the flexcan driver, the ECC mechanism is now
completely disabled instead of masking the interrupts.
The next three patches all target the peak_usb driver. Stephane Grosjean's
patch fixes a potential out-of-sync while decoding packets, Johan Hovold's
patch fixes a slab info leak, Jeroen Hofstee's patch adds missing reporting of
bus off recovery events.
Followed by three patches for the c_can driver. Kurt Van Dijck's patch fixes
detection of potential missing status IRQs, Jeroen Hofstee's patches add a chip
reset on open and add missing reporting of bus off recovery events.
Appana Durga Kedareswara rao's patch for the xilinx driver fixes the flags
field initialization for axi CAN.
The next seven patches target the rx-offload helper, they are by me and Jeroen
Hofstee. The error handling in case of a queue overflow is fixed removing a
memory leak. Further the error handling in case of queue overflow and skb OOM
is cleaned up.
The next two patches are by me and target the flexcan and ti_hecc driver. In
case of a error during can_rx_offload_queue_sorted() the error counters in the
drivers are incremented.
Jeroen Hofstee provides 6 patches for the ti_hecc driver, which properly stop
the device in ifdown, improve the rx-offload support (which hit mainline in
v5.4-rc1), and add missing FIFO overflow and state change reporting.
The following four patches target the j1939 protocol. Colin Ian King's patch
fixes a memory leak in the j1939_sk_errqueue() handling. Three patches by
Oleksij Rempel fix a memory leak on socket release and fix the EOMA packet in
the transport protocol.
Timo Schlüßler's patch fixes a potential race condition in the mcp251x driver
on after suspend.
The last patch is by Yegor Yefremov and updates the SPDX-License-Identifier to
v3.0.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Yegor Yefremov [Thu, 19 Sep 2019 13:53:04 +0000 (15:53 +0200)]
can: don't use deprecated license identifiers
The "GPL-2.0" license identifier changed to "GPL-2.0-only" in SPDX v3.0.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Timo Schlüßler [Fri, 11 Oct 2019 13:38:19 +0000 (15:38 +0200)]
can: mcp251x: mcp251x_restart_work_handler(): Fix potential force_quit race condition
In mcp251x_restart_work_handler() the variable to stop the interrupt
handler (priv->force_quit) is reset after the chip is restarted and thus
a interrupt might occur.
This patch fixes the potential race condition by resetting force_quit
before enabling interrupts.
Signed-off-by: Timo Schlüßler <schluessler@krause.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Oleksij Rempel [Fri, 25 Oct 2019 13:04:13 +0000 (15:04 +0200)]
can: j1939: transport: j1939_xtp_rx_eoma_one(): Add sanity check for correct total message size
We were sending malformed EOMA with total message size set to 0. This
issue has been fixed in the previous patch.
In this patch a sanity check is added to the RX path and a error message
is displayed.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Oleksij Rempel [Fri, 25 Oct 2019 13:04:13 +0000 (15:04 +0200)]
can: j1939: transport: j1939_session_fresh_new(): make sure EOMA is send with the total message size set
We were sending malformed EOMA messageswith total message size set to 0.
This patch fixes the bug.
Reported-by: https://github.com/linux-can/can-utils/issues/159
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Oleksij Rempel [Thu, 10 Oct 2019 10:50:31 +0000 (12:50 +0200)]
can: j1939: fix memory leak if filters was set
Filters array is coped from user space and linked to the j1939 socket.
On socket release this memory was not freed.
Fixes: 9d71dd0c7009 ("can: add support of SAE J1939 protocol")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Colin Ian King [Wed, 18 Sep 2019 10:11:56 +0000 (11:11 +0100)]
can: j1939: fix resource leak of skb on error return paths
Currently the error return paths do not free skb and this results in a
memory leak. Fix this by freeing them before the return.
Addresses-Coverity: ("Resource leak")
Fixes: 9d71dd0c7009 ("can: add support of SAE J1939 protocol")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Jeroen Hofstee [Tue, 24 Sep 2019 18:46:06 +0000 (18:46 +0000)]
can: ti_hecc: add missing state changes
While the ti_hecc has interrupts to report when the error counters increase
to a certain level and which change state it doesn't handle the case that
the error counters go down again, so the reported state can actually be
wrong. Since there is no interrupt for that, do update state based on the
error counters, when the state is not error active and goes down again.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Jeroen Hofstee [Tue, 24 Sep 2019 18:46:03 +0000 (18:46 +0000)]
can: ti_hecc: properly report state changes
The HECC_CANES register handles the flags specially, it only updates
the flags after a one is written to them. Since the interrupt for
frame errors is not enabled an old error can hence been seen when a
state interrupt arrives. For example if the device is not connected
to the CAN-bus the error warning interrupt will have HECC_CANES
indicating there is no ack. The error passive interrupt thereafter
will have HECC_CANES flagging that there is a warning level. And if
thereafter there is a message successfully send HECC_CANES points to
an error passive event, while in reality it became error warning
again. In summary, the state is not always reported correctly.
So handle the state changes and frame errors separately. The state
changes are now based on the interrupt flags and handled directly
when they occur. The reporting of the frame errors is still done as
before, as a side effect of another interrupt.
note: the hecc_clear_bit will do a read, modify, write. So it will
not only clear the bit, but also reset all other bits being set as
a side affect, hence it is replaced with only clearing the flags.
note: The HECC_CANMC_CCR is no longer cleared in the state change
interrupt, it is completely unrelated.
And use net_ratelimit to make checkpatch happy.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Jeroen Hofstee [Tue, 24 Sep 2019 18:46:00 +0000 (18:46 +0000)]
can: ti_hecc: add fifo overflow error reporting
When the rx FIFO overflows the ti_hecc would silently drop them since
the overwrite protection is enabled for all mailboxes. So disable it for
the lowest priority mailbox and return a proper error value when receive
message lost is set. Drop the message itself in that case, since it
might be partially updated.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Acked-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Jeroen Hofstee [Tue, 24 Sep 2019 18:45:49 +0000 (18:45 +0000)]
can: ti_hecc: release the mailbox a bit earlier
Release the mailbox after reading it, so it can be reused a bit earlier.
Since "can: rx-offload: continue on error" all pending message bits are
cleared directly, so remove clearing them in ti_hecc.
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Jeroen Hofstee [Tue, 24 Sep 2019 18:45:56 +0000 (18:45 +0000)]
can: ti_hecc: keep MIM and MD set
The HECC_CANMIM is set in the xmit path and cleared in the interrupt.
Since this is done with a read, modify, write action the register might
end up with some more MIM enabled then intended, since it is not
protected. That doesn't matter at all, since the tx interrupt disables
the mailbox with HECC_CANME (while holding a spinlock). So lets just
always keep MIM set.
While at it, since the mailbox direction never changes, don't set it
every time a message is send, ti_hecc_reset() already sets them to tx.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Jeroen Hofstee [Tue, 24 Sep 2019 18:45:52 +0000 (18:45 +0000)]
can: ti_hecc: ti_hecc_stop(): stop the CPK on down
When the interface goes down, the CPK should no longer take an active
part in the CAN-bus communication, like sending acks and error frames.
So enable configuration mode in ti_hecc_stop, so the CPK is no longer
active.
When a transceiver switch is present the acks and errors don't make it
to the bus, but disabling the CPK then does prevent oddities, like
ti_hecc_reset() failing, since the CPK can become bus-off and starts
counting the 11 bit recessive bits, which seems to block the reset. It
can also cause invalid interrupts and disrupt the CAN-bus, since
transmission can be stopped in the middle of a message, by disabling the
tranceiver while the CPK is sending.
Since the CPK is disabled after normal power on, it is typically only
seen when the interface is restarted.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Mon, 15 Jul 2019 18:53:08 +0000 (20:53 +0200)]
can: ti_hecc: ti_hecc_error(): increase error counters if skb enqueueing via can_rx_offload_queue_sorted() fails
The call to can_rx_offload_queue_sorted() may fail and return an error
(in the current implementation due to resource shortage). The passed skb
is consumed.
This patch adds incrementing of the appropriate error counters to let
the device statistics reflect that there's a problem.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Mon, 15 Jul 2019 18:53:08 +0000 (20:53 +0200)]
can: flexcan: increase error counters if skb enqueueing via can_rx_offload_queue_sorted() fails
The call to can_rx_offload_queue_sorted() may fail and return an error
(in the current implementation due to resource shortage). The passed skb
is consumed.
This patch adds incrementing of the appropriate error counters to let
the device statistics reflect that there's a problem.
Reported-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Tue, 24 Sep 2019 18:45:38 +0000 (18:45 +0000)]
can: rx-offload: can_rx_offload_irq_offload_fifo(): continue on error
In case of a resource shortage, i.e. the rx_offload queue will overflow
or a skb fails to be allocated (due to OOM),
can_rx_offload_offload_one() will call mailbox_read() to discard the
mailbox and return an ERR_PTR.
If the hardware FIFO is empty can_rx_offload_offload_one() will return
NULL.
In case a CAN frame was read from the hardware,
can_rx_offload_offload_one() returns the skb containing it.
Without this patch can_rx_offload_irq_offload_fifo() bails out if no skb
returned, regardless of the reason.
Similar to can_rx_offload_irq_offload_timestamp() in case of a resource
shortage the whole FIFO should be discarded, to avoid an IRQ storm and
give the system some time to recover. However if the FIFO is empty the
loop can be left.
With this patch the loop is left in case of empty FIFO, but not on
errors.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Jeroen Hofstee [Tue, 24 Sep 2019 18:45:38 +0000 (18:45 +0000)]
can: rx-offload: can_rx_offload_irq_offload_timestamp(): continue on error
In case of a resource shortage, i.e. the rx_offload queue will overflow
or a skb fails to be allocated (due to OOM),
can_rx_offload_offload_one() will call mailbox_read() to discard the
mailbox and return an ERR_PTR.
However can_rx_offload_irq_offload_timestamp() bails out in the error
case. In case of a resource shortage all mailboxes should be discarded,
to avoid an IRQ storm and give the system some time to recover.
Since can_rx_offload_irq_offload_timestamp() is typically called from a
while loop, all message will eventually be discarded. So let's continue
on error instead to discard them directly.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Wed, 9 Oct 2019 19:00:32 +0000 (21:00 +0200)]
can: rx-offload: can_rx_offload_offload_one(): use ERR_PTR() to propagate error value in case of errors
Before this patch can_rx_offload_offload_one() returns a pointer to a
skb containing the read CAN frame or a NULL pointer.
However the meaning of the NULL pointer is ambiguous, it can either mean
the requested mailbox is empty or there was an error.
This patch fixes this situation by returning:
- pointer to skb on success
- NULL pointer if mailbox is empty
- ERR_PTR() in case of an error
All users of can_rx_offload_offload_one() have been adopted, no
functional change intended.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Wed, 9 Oct 2019 13:15:07 +0000 (15:15 +0200)]
can: rx-offload: can_rx_offload_offload_one(): increment rx_fifo_errors on queue overflow or OOM
If the rx-offload skb_queue is full or the skb allocation fails (due to OOM),
the mailbox contents is discarded.
This patch adds the incrementing of the rx_fifo_errors statistics counter.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Wed, 9 Oct 2019 14:03:18 +0000 (16:03 +0200)]
can: rx-offload: can_rx_offload_offload_one(): do not increase the skb_queue beyond skb_queue_len_max
The skb_queue is a linked list, holding the skb to be processed in the
next NAPI call.
Without this patch, the queue length in can_rx_offload_offload_one() is
limited to skb_queue_len_max + 1. As the skb_queue is a linked list, no
array or other resources are accessed out-of-bound, however this
behaviour is counterintuitive.
This patch limits the rx-offload skb_queue length to skb_queue_len_max.
Fixes: d254586c3453 ("can: rx-offload: Add support for HW fifo based irq offloading")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Wed, 9 Oct 2019 13:48:48 +0000 (15:48 +0200)]
can: rx-offload: can_rx_offload_queue_tail(): fix error handling, avoid skb mem leak
If the rx-offload skb_queue is full can_rx_offload_queue_tail() will not
queue the skb and return with an error.
This patch frees the skb in case of a full queue, which brings
can_rx_offload_queue_tail() in line with the
can_rx_offload_queue_sorted() function, which has been adjusted in the
previous patch.
The return value is adjusted to -ENOBUFS to better reflect the actual
problem.
The device stats handling is left to the caller.
Fixes: d254586c3453 ("can: rx-offload: Add support for HW fifo based irq offloading")
Reported-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Wed, 9 Oct 2019 13:48:48 +0000 (15:48 +0200)]
can: rx-offload: can_rx_offload_queue_sorted(): fix error handling, avoid skb mem leak
If the rx-offload skb_queue is full can_rx_offload_queue_sorted() will
not queue the skb and return with an error.
None of the callers of this function, issue a kfree_skb() to free the
not queued skb. This results in a memory leak.
This patch fixes the problem by freeing the skb in case of a full queue.
The return value is adjusted to -ENOBUFS to better reflect the actual
problem.
The device stats handling is left to the callers, as this function might
be used in both the rx and tx path.
Fixes: 55059f2b7f86 ("can: rx-offload: introduce can_rx_offload_get_echo_skb() and can_rx_offload_queue_sorted() functions")
Cc: linux-stable <stable@vger.kernel.org>
Cc: Martin Hundebøll <martin@geanix.com>
Reported-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Appana Durga Kedareswara rao [Wed, 9 Oct 2019 07:29:47 +0000 (12:59 +0530)]
can: xilinx_can: Fix flags field initialization for axi can
AXI CANIP doesn't support tx fifo empty interrupt feature(TXFEMP),
update the flags filed in the driver for AXI CAN case accordingly.
Fixes: 3281b380ec9f ("can: xilinx_can: Fix flags field initialization for axi can and canps")
Reported-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Jeroen Hofstee [Tue, 1 Oct 2019 21:01:24 +0000 (21:01 +0000)]
can: c_can: C_CAN: add bus recovery events
While the state is updated when the error counters increase and
decrease, there is no event when the bus recovers and the error counters
decrease again. So add that event as well.
Change the state going downward to be ERROR_PASSIVE -> ERROR_WARNING ->
ERROR_ACTIVE instead of directly to ERROR_ACTIVE again.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Acked-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Tested-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Jeroen Hofstee [Tue, 1 Oct 2019 21:01:20 +0000 (21:01 +0000)]
can: c_can: D_CAN: c_can_chip_config(): perform a sofware reset on open
When the CAN interface is closed it the hardwre is put in power down
mode, but does not reset the error counters / state. Reset the D_CAN on
open, so the reported state and the actual state match.
According to [1], the C_CAN module doesn't have the software reset.
[1] http://www.bosch-semiconductors.com/media/ip_modules/pdf_2/c_can_fd8/users_manual_c_can_fd8_r210_1.pdf
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Kurt Van Dijck [Tue, 1 Oct 2019 07:40:36 +0000 (09:40 +0200)]
can: c_can: c_can_poll(): only read status register after status IRQ
When the status register is read without the status IRQ pending, the
chip may not raise the interrupt line for an upcoming status interrupt
and the driver may miss a status interrupt.
It is critical that the BUSOFF status interrupt is forwarded to the
higher layers, since no more interrupts will follow without
intervention.
Thanks to Wolfgang and Joe for bringing up the first idea.
Signed-off-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Joe Burmeister <joe.burmeister@devtank.co.uk>
Fixes: fa39b54ccf28 ("can: c_can: Get rid of pointless interrupts")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Jeroen Hofstee [Wed, 25 Sep 2019 08:58:45 +0000 (08:58 +0000)]
can: peak_usb: report bus recovery as well
While the state changes are reported when the error counters increase
and decrease, there is no event when the bus recovers and the error
counters decrease again. So add those as well.
Change the state going downward to be ERROR_PASSIVE -> ERROR_WARNING ->
ERROR_ACTIVE instead of directly to ERROR_ACTIVE again.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Johan Hovold [Wed, 23 Oct 2019 08:27:05 +0000 (10:27 +0200)]
can: peak_usb: fix slab info leak
Fix a small slab info leak due to a failure to clear the command buffer
at allocation.
The first 16 bytes of the command buffer are always sent to the device
in pcan_usb_send_cmd() even though only the first two may have been
initialised in case no argument payload is provided (e.g. when waiting
for a response).
Fixes: bb4785551f64 ("can: usb: PEAK-System Technik USB adapters driver core")
Cc: stable <stable@vger.kernel.org> # 3.4
Reported-by: syzbot+863724e7128e14b26732@syzkaller.appspotmail.com
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Stephane Grosjean [Tue, 8 Oct 2019 08:35:44 +0000 (10:35 +0200)]
can: peak_usb: fix a potential out-of-sync while decoding packets
When decoding a buffer received from PCAN-USB, the first timestamp read in
a packet is a 16-bit coded time base, and the next ones are an 8-bit
offset to this base, regardless of the type of packet read.
This patch corrects a potential loss of synchronization by using a
timestamp index read from the buffer, rather than an index of received
data packets, to determine on the sizeof the timestamp to be read from the
packet being decoded.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Fixes: 46be265d3388 ("can: usb: PEAK-System Technik PCAN-USB specific part")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Joakim Zhang [Thu, 15 Aug 2019 08:00:26 +0000 (08:00 +0000)]
can: flexcan: disable completely the ECC mechanism
The ECC (memory error detection and correction) mechanism can be
activated or not, controlled by the ECCDIS bit in CAN_MECR. When
disabled, updates on indications and reporting registers are stopped.
So if want to disable ECC completely, had better assert ECCDIS bit, not
just mask the related interrupts.
Fixes: cdce844865be ("can: flexcan: add vf610 support for FlexCAN")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Johan Hovold [Tue, 1 Oct 2019 10:29:14 +0000 (12:29 +0200)]
can: usb_8dev: fix use-after-free on disconnect
The driver was accessing its driver data after having freed it.
Fixes: 0024d8ad1639 ("can: usb_8dev: Add support for USB2CAN interface from 8 devices")
Cc: stable <stable@vger.kernel.org> # 3.9
Cc: Bernd Krumboeck <b.krumboeck@gmail.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Johan Hovold [Tue, 1 Oct 2019 10:29:13 +0000 (12:29 +0200)]
can: mcba_usb: fix use-after-free on disconnect
The driver was accessing its driver data after having freed it.
Fixes: 51f3baad7de9 ("can: mcba_usb: Add support for Microchip CAN BUS Analyzer")
Cc: stable <stable@vger.kernel.org> # 4.12
Cc: Remigiusz Kołłątaj <remigiusz.kollataj@mobica.com>
Reported-by: syzbot+e29b17e5042bbc56fae9@syzkaller.appspotmail.com
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Navid Emamdoost [Fri, 20 Sep 2019 02:44:38 +0000 (21:44 -0500)]
can: gs_usb: gs_can_open(): prevent memory leak
In gs_can_open() if usb_submit_urb() fails the allocated urb should be
released.
Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Wen Yang [Sat, 28 Sep 2019 14:29:05 +0000 (22:29 +0800)]
can: dev: add missing of_node_put() after calling of_get_child_by_name()
of_node_put() needs to be called when the device node which is got
from of_get_child_by_name() finished using.
Fixes: 2290aefa2e90 ("can: dev: Add support for limiting configured bitrate")
Cc: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Wen Yang <wenyang@linux.alibaba.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Pablo Neira Ayuso [Mon, 4 Nov 2019 19:59:00 +0000 (20:59 +0100)]
Merge branch 'master' of git://blackhole.kfki.hu/nf
Jozsef Kadlecsik says:
====================
ipset patches for nf
- Fix the error code in ip_set_sockfn_get() when copy_to_user() is used,
from Dan Carpenter.
- The IPv6 part was missed when fixing copying the right MAC address
in the patch "netfilter: ipset: Copy the right MAC address in bitmap:ip,mac
and hash:ip,mac sets", it is completed now by Stefano Brivio.
- ipset nla_policies are fixed to fully support NL_VALIDATE_STRICT and
the code is converted from deprecated parsings to verified ones.
====================
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
git.samba.org / sfrench / cifs-2.6.git / log