--- /dev/null
+/*
+ * sata_sil24.c - Driver for Silicon Image 3124/3132 SATA-2 controllers
+ *
+ * Copyright 2005 Tejun Heo
+ *
+ * Based on preview driver from Silicon Image.
+ *
+ * NOTE: No NCQ/ATAPI support yet. The preview driver didn't support
+ * NCQ nor ATAPI, and, unfortunately, I couldn't find out how to make
+ * those work. Enabling those shouldn't be difficult. Basic
+ * structure is all there (in libata-dev tree). If you have any
+ * information about this hardware, please contact me or linux-ide.
+ * Info is needed on...
+ *
+ * - How to issue tagged commands and turn on sactive on issue accordingly.
+ * - Where to put an ATAPI command and how to tell the device to send it.
+ * - How to enable/use 64bit.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2, or (at your option) any
+ * later version.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/dma-mapping.h>
+#include <scsi/scsi_host.h>
+#include "scsi.h"
+#include <linux/libata.h>
+#include <asm/io.h>
+
+#define DRV_NAME "sata_sil24"
+#define DRV_VERSION "0.20" /* Silicon Image's preview driver was 0.10 */
+
+#define NR_PORTS 4
+
+/*
+ * Port request block (PRB) 32 bytes
+ */
+struct sil24_prb {
+ u16 ctrl;
+ u16 prot;
+ u32 rx_cnt;
+ u8 fis[6 * 4];
+};
+
+/*
+ * Scatter gather entry (SGE) 16 bytes
+ */
+struct sil24_sge {
+ u64 addr;
+ u32 cnt;
+ u32 flags;
+};
+
+/*
+ * Port multiplier
+ */
+struct sil24_port_multiplier {
+ u32 diag;
+ u32 sactive;
+};
+
+enum {
+ /*
+ * Global controller registers (128 bytes @ BAR0)
+ */
+ /* 32 bit regs */
+ HOST_SLOT_STAT = 0x00, /* 32 bit slot stat * 4 */
+ HOST_CTRL = 0x40,
+ HOST_IRQ_STAT = 0x44,
+ HOST_PHY_CFG = 0x48,
+ HOST_BIST_CTRL = 0x50,
+ HOST_BIST_PTRN = 0x54,
+ HOST_BIST_STAT = 0x58,
+ HOST_MEM_BIST_STAT = 0x5c,
+ HOST_FLASH_CMD = 0x70,
+ /* 8 bit regs */
+ HOST_FLASH_DATA = 0x74,
+ HOST_TRANSITION_DETECT = 0x75,
+ HOST_GPIO_CTRL = 0x76,
+ HOST_I2C_ADDR = 0x78, /* 32 bit */
+ HOST_I2C_DATA = 0x7c,
+ HOST_I2C_XFER_CNT = 0x7e,
+ HOST_I2C_CTRL = 0x7f,
+
+ /* HOST_SLOT_STAT bits */
+ HOST_SSTAT_ATTN = (1 << 31),
+
+ /*
+ * Port registers
+ * (8192 bytes @ +0x0000, +0x2000, +0x4000 and +0x6000 @ BAR2)
+ */
+ PORT_REGS_SIZE = 0x2000,
+ PORT_PRB = 0x0000, /* (32 bytes PRB + 16 bytes SGEs * 6) * 31 (3968 bytes) */
+ /* TF is overlayed w/ PRB regs in the preview driver,
+ * but it doesn't seem to work. */
+ PORT_TF = 0x0000,
+
+ PORT_PM = 0x0f80, /* 8 bytes PM * 16 (128 bytes) */
+ /* 32 bit regs */
+ PORT_CTRL_STAT = 0x1000, /* write:ctrl, read:stat */
+ PORT_CTRL_CLR = 0x1004,
+ PORT_IRQ_STAT = 0x1008,
+ PORT_IRQ_ENABLE_SET = 0x1010,
+ PORT_IRQ_ENABLE_CLR = 0x1014,
+ PORT_ACTIVATE_UPPER_ADDR= 0x101c,
+ PORT_EXEC_FIFO = 0x1020,
+ PORT_CMD_ERR = 0x1024,
+ PORT_FIS_CFG = 0x1028,
+ PORT_FIFO_THRES = 0x102c,
+ /* 16 bit regs */
+ PORT_DECODE_ERR_CNT = 0x1040,
+ PORT_DECODE_ERR_THRESH = 0x1042,
+ PORT_CRC_ERR_CNT = 0x1044,
+ PORT_CRC_ERR_THRESH = 0x1046,
+ PORT_HSHK_ERR_CNT = 0x1048,
+ PORT_HSHK_ERR_THRESH = 0x104a,
+ /* 32 bit regs */
+ PORT_PHY_CFG = 0x1050,
+ PORT_SLOT_STAT = 0x1800,
+ PORT_CMD_ACTIVATE = 0x1c00, /* 64 bit cmd activate * 31 (248 bytes) */
+ PORT_EXEC_DIAG = 0x1e00, /* 32bit exec diag * 16 (64 bytes, 0-10 used on 3124) */
+ PORT_PSD_DIAG = 0x1e40, /* 32bit psd diag * 16 (64 bytes, 0-8 used on 3124) */
+ PORT_SCONTROL = 0x1f00,
+ PORT_SSTATUS = 0x1f04,
+ PORT_SERROR = 0x1f08,
+ PORT_SACTIVE = 0x1f0c,
+
+ /* PORT_CTRL_STAT bits */
+ PORT_CS_PORT_RST = (1 << 0), /* port reset */
+ PORT_CS_DEV_RST = (1 << 1), /* device reset */
+ PORT_CS_INIT = (1 << 2), /* port initialize */
+ PORT_CS_IRQ_WOC = (1 << 3), /* interrupt write one to clear */
+ PORT_CS_RESUME = (1 << 4), /* port resume */
+ PORT_CS_32BIT_ACTV = (1 << 5), /* 32-bit activation */
+ PORT_CS_PM_EN = (1 << 6), /* port multiplier enable */
+ PORT_CS_RDY = (1 << 7), /* port ready to accept commands */
+
+ /* PORT_IRQ_STAT/ENABLE_SET/CLR */
+ /* bits[11:0] are masked */
+ PORT_IRQ_COMPLETE = (1 << 0), /* command(s) completed */
+ PORT_IRQ_ERROR = (1 << 1), /* command execution error */
+ PORT_IRQ_PORTRDY_CHG = (1 << 2), /* port ready change */
+ PORT_IRQ_PWR_CHG = (1 << 3), /* power management change */
+ PORT_IRQ_PHYRDY_CHG = (1 << 4), /* PHY ready change */
+ PORT_IRQ_COMWAKE = (1 << 5), /* COMWAKE received */
+ PORT_IRQ_UNK_FIS = (1 << 6), /* Unknown FIS received */
+ PORT_IRQ_SDB_FIS = (1 << 11), /* SDB FIS received */
+
+ /* bits[27:16] are unmasked (raw) */
+ PORT_IRQ_RAW_SHIFT = 16,
+ PORT_IRQ_MASKED_MASK = 0x7ff,
+ PORT_IRQ_RAW_MASK = (0x7ff << PORT_IRQ_RAW_SHIFT),
+
+ /* ENABLE_SET/CLR specific, intr steering - 2 bit field */
+ PORT_IRQ_STEER_SHIFT = 30,
+ PORT_IRQ_STEER_MASK = (3 << PORT_IRQ_STEER_SHIFT),
+
+ /* PORT_CMD_ERR constants */
+ PORT_CERR_DEV = 1, /* Error bit in D2H Register FIS */
+ PORT_CERR_SDB = 2, /* Error bit in SDB FIS */
+ PORT_CERR_DATA = 3, /* Error in data FIS not detected by dev */
+ PORT_CERR_SEND = 4, /* Initial cmd FIS transmission failure */
+ PORT_CERR_INCONSISTENT = 5, /* Protocol mismatch */
+ PORT_CERR_DIRECTION = 6, /* Data direction mismatch */
+ PORT_CERR_UNDERRUN = 7, /* Ran out of SGEs while writing */
+ PORT_CERR_OVERRUN = 8, /* Ran out of SGEs while reading */
+ PORT_CERR_PKT_PROT = 11, /* DIR invalid in 1st PIO setup of ATAPI */
+ PORT_CERR_SGT_BOUNDARY = 16, /* PLD ecode 00 - SGT not on qword boundary */
+ PORT_CERR_SGT_TGTABRT = 17, /* PLD ecode 01 - target abort */
+ PORT_CERR_SGT_MSTABRT = 18, /* PLD ecode 10 - master abort */
+ PORT_CERR_SGT_PCIPERR = 19, /* PLD ecode 11 - PCI parity err while fetching SGT */
+ PORT_CERR_CMD_BOUNDARY = 24, /* ctrl[15:13] 001 - PRB not on qword boundary */
+ PORT_CERR_CMD_TGTABRT = 25, /* ctrl[15:13] 010 - target abort */
+ PORT_CERR_CMD_MSTABRT = 26, /* ctrl[15:13] 100 - master abort */
+ PORT_CERR_CMD_PCIPERR = 27, /* ctrl[15:13] 110 - PCI parity err while fetching PRB */
+ PORT_CERR_XFR_UNDEF = 32, /* PSD ecode 00 - undefined */
+ PORT_CERR_XFR_TGTABRT = 33, /* PSD ecode 01 - target abort */
+ PORT_CERR_XFR_MSGABRT = 34, /* PSD ecode 10 - master abort */
+ PORT_CERR_XFR_PCIPERR = 35, /* PSD ecode 11 - PCI prity err during transfer */
+ PORT_CERR_SENDSERVICE = 36, /* FIS received whiel sending service */
+
+ /*
+ * Other constants
+ */
+ SGE_TRM = (1 << 31), /* Last SGE in chain */
+ PRB_SOFT_RST = (1 << 7), /* Soft reset request (ign BSY?) */
+
+ /* board id */
+ BID_SIL3124 = 0,
+ BID_SIL3132 = 1,
+
+ IRQ_STAT_4PORTS = 0xf,
+};
+
+struct sil24_cmd_block {
+ struct sil24_prb prb;
+ struct sil24_sge sge[LIBATA_MAX_PRD];
+};
+
+/*
+ * ap->private_data
+ *
+ * The preview driver always returned 0 for status. We emulate it
+ * here from the previous interrupt.
+ */
+struct sil24_port_priv {
+ void *port;
+ struct sil24_cmd_block *cmd_block; /* 32 cmd blocks */
+ dma_addr_t cmd_block_dma; /* DMA base addr for them */
+};
+
+/* ap->host_set->private_data */
+struct sil24_host_priv {
+ void *host_base; /* global controller control (128 bytes @BAR0) */
+ void *port_base; /* port registers (4 * 8192 bytes @BAR2) */
+};
+
+static u8 sil24_check_status(struct ata_port *ap);
+static u8 sil24_check_err(struct ata_port *ap);
+static u32 sil24_scr_read(struct ata_port *ap, unsigned sc_reg);
+static void sil24_scr_write(struct ata_port *ap, unsigned sc_reg, u32 val);
+static void sil24_phy_reset(struct ata_port *ap);
+static void sil24_qc_prep(struct ata_queued_cmd *qc);
+static int sil24_qc_issue(struct ata_queued_cmd *qc);
+static void sil24_irq_clear(struct ata_port *ap);
+static void sil24_eng_timeout(struct ata_port *ap);
+static irqreturn_t sil24_interrupt(int irq, void *dev_instance, struct pt_regs *regs);
+static int sil24_port_start(struct ata_port *ap);
+static void sil24_port_stop(struct ata_port *ap);
+static void sil24_host_stop(struct ata_host_set *host_set);
+static int sil24_init_one(struct pci_dev *pdev, const struct pci_device_id *ent);
+
+static struct pci_device_id sil24_pci_tbl[] = {
+ { 0x1095, 0x3124, PCI_ANY_ID, PCI_ANY_ID, 0, 0, BID_SIL3124 },
+ { 0x1095, 0x3132, PCI_ANY_ID, PCI_ANY_ID, 0, 0, BID_SIL3132 },
+};
+
+static struct pci_driver sil24_pci_driver = {
+ .name = DRV_NAME,
+ .id_table = sil24_pci_tbl,
+ .probe = sil24_init_one,
+ .remove = ata_pci_remove_one, /* safe? */
+};
+
+static Scsi_Host_Template sil24_sht = {
+ .module = THIS_MODULE,
+ .name = DRV_NAME,
+ .ioctl = ata_scsi_ioctl,
+ .queuecommand = ata_scsi_queuecmd,
+ .eh_strategy_handler = ata_scsi_error,
+ .can_queue = ATA_DEF_QUEUE,
+ .this_id = ATA_SHT_THIS_ID,
+ .sg_tablesize = LIBATA_MAX_PRD,
+ .max_sectors = ATA_MAX_SECTORS,
+ .cmd_per_lun = ATA_SHT_CMD_PER_LUN,
+ .emulated = ATA_SHT_EMULATED,
+ .use_clustering = ATA_SHT_USE_CLUSTERING,
+ .proc_name = DRV_NAME,
+ .dma_boundary = ATA_DMA_BOUNDARY,
+ .slave_configure = ata_scsi_slave_config,
+ .bios_param = ata_std_bios_param,
+ .ordered_flush = 1, /* NCQ not supported yet */
+};
+
+static struct ata_port_operations sil24_ops = {
+ .port_disable = ata_port_disable,
+
+ .check_status = sil24_check_status,
+ .check_altstatus = sil24_check_status,
+ .check_err = sil24_check_err,
+ .dev_select = ata_noop_dev_select,
+
+ .phy_reset = sil24_phy_reset,
+
+ .qc_prep = sil24_qc_prep,
+ .qc_issue = sil24_qc_issue,
+
+ .eng_timeout = sil24_eng_timeout,
+
+ .irq_handler = sil24_interrupt,
+ .irq_clear = sil24_irq_clear,
+
+ .scr_read = sil24_scr_read,
+ .scr_write = sil24_scr_write,
+
+ .port_start = sil24_port_start,
+ .port_stop = sil24_port_stop,
+ .host_stop = sil24_host_stop,
+};
+
+static struct ata_port_info sil24_port_info[] = {
+ /* sil_3124 */
+ {
+ .sht = &sil24_sht,
+ .host_flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
+ ATA_FLAG_SATA_RESET | ATA_FLAG_MMIO |
+ ATA_FLAG_PIO_DMA,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .mwdma_mask = 0x07, /* mwdma0-2 */
+ .udma_mask = 0x3f, /* udma0-5 */
+ .port_ops = &sil24_ops,
+ },
+ /* sil_3132 */
+ {
+ .sht = &sil24_sht,
+ .host_flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
+ ATA_FLAG_SATA_RESET | ATA_FLAG_MMIO |
+ ATA_FLAG_PIO_DMA,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .mwdma_mask = 0x07, /* mwdma0-2 */
+ .udma_mask = 0x3f, /* udma0-5 */
+ .port_ops = &sil24_ops,
+ },
+};
+
+static u8 sil24_check_status(struct ata_port *ap)
+{
+ return ATA_DRDY;
+}
+
+static u8 sil24_check_err(struct ata_port *ap)
+{
+ return 0;
+}
+
+static int sil24_scr_map[] = {
+ [SCR_CONTROL] = 0,
+ [SCR_STATUS] = 1,
+ [SCR_ERROR] = 2,
+ [SCR_ACTIVE] = 3,
+};
+
+static u32 sil24_scr_read(struct ata_port *ap, unsigned sc_reg)
+{
+ void *scr_addr = (void *)ap->ioaddr.scr_addr;
+ if (sc_reg < ARRAY_SIZE(sil24_scr_map)) {
+ void *addr;
+ addr = scr_addr + sil24_scr_map[sc_reg] * 4;
+ return readl(scr_addr + sil24_scr_map[sc_reg] * 4);
+ }
+ return 0xffffffffU;
+}
+
+static void sil24_scr_write(struct ata_port *ap, unsigned sc_reg, u32 val)
+{
+ void *scr_addr = (void *)ap->ioaddr.scr_addr;
+ if (sc_reg < ARRAY_SIZE(sil24_scr_map)) {
+ void *addr;
+ addr = scr_addr + sil24_scr_map[sc_reg] * 4;
+ writel(val, scr_addr + sil24_scr_map[sc_reg] * 4);
+ }
+}
+
+static void sil24_phy_reset(struct ata_port *ap)
+{
+ __sata_phy_reset(ap);
+ /*
+ * No ATAPI yet. Just unconditionally indicate ATA device.
+ * If ATAPI device is attached, it will fail ATA_CMD_ID_ATA
+ * and libata core will ignore the device.
+ */
+ if (!(ap->flags & ATA_FLAG_PORT_DISABLED))
+ ap->device[0].class = ATA_DEV_ATA;
+}
+
+static inline void sil24_fill_sg(struct ata_queued_cmd *qc,
+ struct sil24_cmd_block *cb)
+{
+ struct scatterlist *sg = qc->sg;
+ struct sil24_sge *sge = cb->sge;
+ unsigned i;
+
+ for (i = 0; i < qc->n_elem; i++, sg++, sge++) {
+ sge->addr = cpu_to_le64(sg_dma_address(sg));
+ sge->cnt = cpu_to_le32(sg_dma_len(sg));
+ sge->flags = 0;
+ sge->flags = i < qc->n_elem - 1 ? 0 : cpu_to_le32(SGE_TRM);
+ }
+}
+
+static void sil24_qc_prep(struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ struct sil24_port_priv *pp = ap->private_data;
+ struct sil24_cmd_block *cb = pp->cmd_block + qc->tag;
+ struct sil24_prb *prb = &cb->prb;
+
+ switch (qc->tf.protocol) {
+ case ATA_PROT_PIO:
+ case ATA_PROT_DMA:
+ case ATA_PROT_NODATA:
+ break;
+ default:
+ /* ATAPI isn't supported yet */
+ BUG();
+ }
+
+ ata_tf_to_fis(&qc->tf, prb->fis, 0);
+
+ if (qc->flags & ATA_QCFLAG_DMAMAP)
+ sil24_fill_sg(qc, cb);
+}
+
+static int sil24_qc_issue(struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ struct sil24_port_priv *pp = ap->private_data;
+ dma_addr_t paddr = pp->cmd_block_dma + qc->tag * sizeof(*pp->cmd_block);
+
+ writel((u32)paddr, pp->port + PORT_CMD_ACTIVATE);
+ return 0;
+}
+
+static void sil24_irq_clear(struct ata_port *ap)
+{
+ /* unused */
+}
+
+static void sil24_reset_controller(struct ata_port *ap)
+{
+ struct sil24_port_priv *pp = ap->private_data;
+ void *port = pp->port;
+ int cnt;
+ u32 tmp;
+
+ printk(KERN_NOTICE DRV_NAME
+ " ata%u: resetting controller...\n", ap->id);
+
+ /* Reset controller state. Is this correct? */
+ writel(PORT_CS_DEV_RST, port + PORT_CTRL_STAT);
+ readl(port + PORT_CTRL_STAT); /* sync */
+
+ /* Max ~100ms */
+ for (cnt = 0; cnt < 1000; cnt++) {
+ udelay(100);
+ tmp = readl(port + PORT_CTRL_STAT);
+ if (!(tmp & PORT_CS_DEV_RST))
+ break;
+ }
+ if (tmp & PORT_CS_DEV_RST)
+ printk(KERN_ERR DRV_NAME
+ " ata%u: failed to reset controller\n", ap->id);
+}
+
+static void sil24_eng_timeout(struct ata_port *ap)
+{
+ struct ata_queued_cmd *qc;
+
+ qc = ata_qc_from_tag(ap, ap->active_tag);
+ if (!qc) {
+ printk(KERN_ERR "ata%u: BUG: tiemout without command\n",
+ ap->id);
+ return;
+ }
+
+ /*
+ * hack alert! We cannot use the supplied completion
+ * function from inside the ->eh_strategy_handler() thread.
+ * libata is the only user of ->eh_strategy_handler() in
+ * any kernel, so the default scsi_done() assumes it is
+ * not being called from the SCSI EH.
+ */
+ printk(KERN_ERR "ata%u: command timeout\n", ap->id);
+ qc->scsidone = scsi_finish_command;
+ ata_qc_complete(qc, ATA_ERR);
+
+ sil24_reset_controller(ap);
+}
+
+static inline void sil24_host_intr(struct ata_port *ap)
+{
+ struct ata_queued_cmd *qc = ata_qc_from_tag(ap, ap->active_tag);
+ struct sil24_port_priv *pp = ap->private_data;
+ void *port = pp->port;
+ u32 slot_stat;
+
+ slot_stat = readl(port + PORT_SLOT_STAT);
+ if (!(slot_stat & HOST_SSTAT_ATTN)) {
+ if (qc)
+ ata_qc_complete(qc, 0);
+ } else {
+ u32 irq_stat, cmd_err, sstatus, serror;
+
+ irq_stat = readl(port + PORT_IRQ_STAT);
+ cmd_err = readl(port + PORT_CMD_ERR);
+ sstatus = readl(port + PORT_SSTATUS);
+ serror = readl(port + PORT_SERROR);
+
+ /* Clear IRQ/errors */
+ writel(irq_stat, port + PORT_IRQ_STAT);
+ if (cmd_err)
+ writel(cmd_err, port + PORT_CMD_ERR);
+ if (serror)
+ writel(serror, port + PORT_SERROR);
+
+ printk(KERN_ERR DRV_NAME " ata%u: error interrupt on port%d\n"
+ " stat=0x%x irq=0x%x cmd_err=%d sstatus=0x%x serror=0x%x\n",
+ ap->id, ap->port_no, slot_stat, irq_stat, cmd_err, sstatus, serror);
+
+ if (qc)
+ ata_qc_complete(qc, ATA_ERR);
+
+ sil24_reset_controller(ap);
+ }
+}
+
+static irqreturn_t sil24_interrupt(int irq, void *dev_instance, struct pt_regs *regs)
+{
+ struct ata_host_set *host_set = dev_instance;
+ struct sil24_host_priv *hpriv = host_set->private_data;
+ unsigned handled = 0;
+ u32 status;
+ int i;
+
+ status = readl(hpriv->host_base + HOST_IRQ_STAT);
+
+ if (!(status & IRQ_STAT_4PORTS))
+ goto out;
+
+ spin_lock(&host_set->lock);
+
+ for (i = 0; i < host_set->n_ports; i++)
+ if (status & (1 << i)) {
+ struct ata_port *ap = host_set->ports[i];
+ if (ap && !(ap->flags & ATA_FLAG_PORT_DISABLED))
+ sil24_host_intr(host_set->ports[i]);
+ else {
+ u32 tmp;
+ printk(KERN_WARNING DRV_NAME
+ ": spurious interrupt from port %d\n", i);
+ tmp = readl(hpriv->host_base + HOST_CTRL);
+ tmp &= ~(1 << i);
+ writel(tmp, hpriv->host_base + HOST_CTRL);
+ }
+ handled++;
+ }
+
+ spin_unlock(&host_set->lock);
+ out:
+ return IRQ_RETVAL(handled);
+}
+
+static int sil24_port_start(struct ata_port *ap)
+{
+ struct device *dev = ap->host_set->dev;
+ struct sil24_host_priv *hpriv = ap->host_set->private_data;
+ struct sil24_port_priv *pp;
+ struct sil24_cmd_block *cb;
+ size_t cb_size = sizeof(*cb);
+ dma_addr_t cb_dma;
+
+ pp = kmalloc(sizeof(*pp), GFP_KERNEL);
+ if (!pp)
+ return -ENOMEM;
+ memset(pp, 0, sizeof(*pp));
+
+ cb = dma_alloc_coherent(dev, cb_size, &cb_dma, GFP_KERNEL);
+ if (!cb) {
+ kfree(pp);
+ return -ENOMEM;
+ }
+ memset(cb, 0, cb_size);
+
+ pp->port = hpriv->port_base + ap->port_no * PORT_REGS_SIZE;
+ pp->cmd_block = cb;
+ pp->cmd_block_dma = cb_dma;
+
+ ap->private_data = pp;
+
+ return 0;
+}
+
+static void sil24_port_stop(struct ata_port *ap)
+{
+ struct device *dev = ap->host_set->dev;
+ struct sil24_port_priv *pp = ap->private_data;
+ size_t cb_size = sizeof(*pp->cmd_block);
+
+ dma_free_coherent(dev, cb_size, pp->cmd_block, pp->cmd_block_dma);
+ kfree(pp);
+}
+
+static void sil24_host_stop(struct ata_host_set *host_set)
+{
+ struct sil24_host_priv *hpriv = host_set->private_data;
+
+ iounmap(hpriv->host_base);
+ iounmap(hpriv->port_base);
+ kfree(hpriv);
+}
+
+static int sil24_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
+{
+ static int printed_version = 0;
+ unsigned int board_id = (unsigned int)ent->driver_data;
+ struct ata_probe_ent *probe_ent = NULL;
+ struct sil24_host_priv *hpriv = NULL;
+ void *host_base = NULL, *port_base = NULL;
+ int i, rc;
+
+ if (!printed_version++)
+ printk(KERN_DEBUG DRV_NAME " version " DRV_VERSION "\n");
+
+ rc = pci_enable_device(pdev);
+ if (rc)
+ return rc;
+
+ rc = pci_request_regions(pdev, DRV_NAME);
+ if (rc)
+ goto out_disable;
+
+ rc = -ENOMEM;
+ /* ioremap mmio registers */
+ host_base = ioremap(pci_resource_start(pdev, 0),
+ pci_resource_len(pdev, 0));
+ if (!host_base)
+ goto out_free;
+ port_base = ioremap(pci_resource_start(pdev, 2),
+ pci_resource_len(pdev, 2));
+ if (!port_base)
+ goto out_free;
+
+ /* allocate & init probe_ent and hpriv */
+ probe_ent = kmalloc(sizeof(*probe_ent), GFP_KERNEL);
+ if (!probe_ent)
+ goto out_free;
+
+ hpriv = kmalloc(sizeof(*hpriv), GFP_KERNEL);
+ if (!hpriv)
+ goto out_free;
+
+ memset(probe_ent, 0, sizeof(*probe_ent));
+ probe_ent->dev = pci_dev_to_dev(pdev);
+ INIT_LIST_HEAD(&probe_ent->node);
+
+ probe_ent->sht = sil24_port_info[board_id].sht;
+ probe_ent->host_flags = sil24_port_info[board_id].host_flags;
+ probe_ent->pio_mask = sil24_port_info[board_id].pio_mask;
+ probe_ent->udma_mask = sil24_port_info[board_id].udma_mask;
+ probe_ent->port_ops = sil24_port_info[board_id].port_ops;
+ probe_ent->n_ports = (board_id == BID_SIL3124) ? 4 : 2;
+
+ probe_ent->irq = pdev->irq;
+ probe_ent->irq_flags = SA_SHIRQ;
+ probe_ent->mmio_base = port_base;
+ probe_ent->private_data = hpriv;
+
+ memset(hpriv, 0, sizeof(*hpriv));
+ hpriv->host_base = host_base;
+ hpriv->port_base = port_base;
+
+ /*
+ * Configure the device
+ */
+ /*
+ * FIXME: This device is certainly 64-bit capable. We just
+ * don't know how to use it. After fixing 32bit activation in
+ * this function, enable 64bit masks here.
+ */
+ rc = pci_set_dma_mask(pdev, DMA_32BIT_MASK);
+ if (rc) {
+ printk(KERN_ERR DRV_NAME "(%s): 32-bit DMA enable failed\n",
+ pci_name(pdev));
+ goto out_free;
+ }
+ rc = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK);
+ if (rc) {
+ printk(KERN_ERR DRV_NAME "(%s): 32-bit consistent DMA enable failed\n",
+ pci_name(pdev));
+ goto out_free;
+ }
+
+ /* GPIO off */
+ writel(0, host_base + HOST_FLASH_CMD);
+
+ /* Mask interrupts during initialization */
+ writel(0, host_base + HOST_CTRL);
+
+ for (i = 0; i < probe_ent->n_ports; i++) {
+ void *port = port_base + i * PORT_REGS_SIZE;
+ unsigned long portu = (unsigned long)port;
+ u32 tmp;
+ int cnt;
+
+ probe_ent->port[i].cmd_addr = portu + PORT_TF;
+ probe_ent->port[i].ctl_addr = portu + PORT_TF + 0xa;
+ probe_ent->port[i].altstatus_addr = portu + PORT_TF + 0xa;
+ probe_ent->port[i].scr_addr = portu + PORT_SCONTROL;
+
+ ata_std_ports(&probe_ent->port[i]);
+
+ /* Initial PHY setting */
+ writel(0x20c, port + PORT_PHY_CFG);
+
+ /* Clear port RST */
+ tmp = readl(port + PORT_CTRL_STAT);
+ if (tmp & PORT_CS_PORT_RST) {
+ writel(PORT_CS_PORT_RST, port + PORT_CTRL_CLR);
+ readl(port + PORT_CTRL_STAT); /* sync */
+ for (cnt = 0; cnt < 10; cnt++) {
+ msleep(10);
+ tmp = readl(port + PORT_CTRL_STAT);
+ if (!(tmp & PORT_CS_PORT_RST))
+ break;
+ }
+ if (tmp & PORT_CS_PORT_RST)
+ printk(KERN_ERR DRV_NAME
+ "(%s): failed to clear port RST\n",
+ pci_name(pdev));
+ }
+
+ /* Zero error counters. */
+ writel(0x8000, port + PORT_DECODE_ERR_THRESH);
+ writel(0x8000, port + PORT_CRC_ERR_THRESH);
+ writel(0x8000, port + PORT_HSHK_ERR_THRESH);
+ writel(0x0000, port + PORT_DECODE_ERR_CNT);
+ writel(0x0000, port + PORT_CRC_ERR_CNT);
+ writel(0x0000, port + PORT_HSHK_ERR_CNT);
+
+ /* FIXME: 32bit activation? */
+ writel(0, port + PORT_ACTIVATE_UPPER_ADDR);
+ writel(PORT_CS_32BIT_ACTV, port + PORT_CTRL_STAT);
+
+ /* Configure interrupts */
+ writel(0xffff, port + PORT_IRQ_ENABLE_CLR);
+ writel(PORT_IRQ_COMPLETE | PORT_IRQ_ERROR | PORT_IRQ_SDB_FIS,
+ port + PORT_IRQ_ENABLE_SET);
+
+ /* Clear interrupts */
+ writel(0x0fff0fff, port + PORT_IRQ_STAT);
+ writel(PORT_CS_IRQ_WOC, port + PORT_CTRL_CLR);
+ }
+
+ /* Turn on interrupts */
+ writel(IRQ_STAT_4PORTS, host_base + HOST_CTRL);
+
+ pci_set_master(pdev);
+
+ ata_device_add(probe_ent);
+
+ kfree(probe_ent);
+ return 0;
+
+ out_free:
+ if (host_base)
+ iounmap(host_base);
+ if (port_base)
+ iounmap(port_base);
+ kfree(probe_ent);
+ kfree(hpriv);
+ pci_release_regions(pdev);
+ out_disable:
+ pci_disable_device(pdev);
+ return rc;
+}
+
+static int __init sil24_init(void)
+{
+ return pci_module_init(&sil24_pci_driver);
+}
+
+static void __exit sil24_exit(void)
+{
+ pci_unregister_driver(&sil24_pci_driver);
+}
+
+MODULE_AUTHOR("Tejun Heo");
+MODULE_DESCRIPTION("Silicon Image 3124/3132 SATA low-level driver");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, sil24_pci_tbl);
+
+module_init(sil24_init);
+module_exit(sil24_exit);
git.samba.org / sfrench / cifs-2.6.git / commitdiff