CONFIG_ARCH_IQ31244=y
# CONFIG_ARCH_IQ80331 is not set
# CONFIG_MACH_IQ80332 is not set
-CONFIG_ARCH_EP80219=y
#
# IOP3xx Chipset Features
#
# CONFIG_MTD_COMPLEX_MAPPINGS is not set
CONFIG_MTD_PHYSMAP=y
-CONFIG_MTD_PHYSMAP_START=0xf0000000
-CONFIG_MTD_PHYSMAP_LEN=0x00800000
-CONFIG_MTD_PHYSMAP_BANKWIDTH=2
+CONFIG_MTD_PHYSMAP_START=0x0
+CONFIG_MTD_PHYSMAP_LEN=0x0
+CONFIG_MTD_PHYSMAP_BANKWIDTH=1
# CONFIG_MTD_ARM_INTEGRATOR is not set
# CONFIG_MTD_EDB7312 is not set
CONFIG_ARCH_IQ31244=y
# CONFIG_ARCH_IQ80331 is not set
# CONFIG_MACH_IQ80332 is not set
-# CONFIG_ARCH_EP80219 is not set
#
# IOP3xx Chipset Features
#
# CONFIG_MTD_COMPLEX_MAPPINGS is not set
CONFIG_MTD_PHYSMAP=y
-CONFIG_MTD_PHYSMAP_START=0xf0000000
-CONFIG_MTD_PHYSMAP_LEN=0x00800000
-CONFIG_MTD_PHYSMAP_BANKWIDTH=2
+CONFIG_MTD_PHYSMAP_START=0x0
+CONFIG_MTD_PHYSMAP_LEN=0x0
+CONFIG_MTD_PHYSMAP_BANKWIDTH=1
# CONFIG_MTD_ARM_INTEGRATOR is not set
# CONFIG_MTD_EDB7312 is not set
# CONFIG_ARCH_IQ31244 is not set
# CONFIG_ARCH_IQ80331 is not set
# CONFIG_MACH_IQ80332 is not set
-# CONFIG_ARCH_EP80219 is not set
#
# IOP3xx Chipset Features
#
# CONFIG_MTD_COMPLEX_MAPPINGS is not set
CONFIG_MTD_PHYSMAP=y
-CONFIG_MTD_PHYSMAP_START=0xf0000000
-CONFIG_MTD_PHYSMAP_LEN=0x00800000
+CONFIG_MTD_PHYSMAP_START=0x0
+CONFIG_MTD_PHYSMAP_LEN=0x0
CONFIG_MTD_PHYSMAP_BANKWIDTH=1
# CONFIG_MTD_ARM_INTEGRATOR is not set
# CONFIG_MTD_EDB7312 is not set
# CONFIG_ARCH_IQ31244 is not set
CONFIG_ARCH_IQ80331=y
# CONFIG_MACH_IQ80332 is not set
-# CONFIG_ARCH_EP80219 is not set
-
-#
-# IOP3xx Chipset Features
-#
-CONFIG_IOP331_STEPD=y
#
# Processor Type
#
# CONFIG_MTD_COMPLEX_MAPPINGS is not set
CONFIG_MTD_PHYSMAP=y
-CONFIG_MTD_PHYSMAP_START=0xc0000000
-CONFIG_MTD_PHYSMAP_LEN=0x00800000
+CONFIG_MTD_PHYSMAP_START=0x0
+CONFIG_MTD_PHYSMAP_LEN=0x0
CONFIG_MTD_PHYSMAP_BANKWIDTH=1
# CONFIG_MTD_ARM_INTEGRATOR is not set
# CONFIG_MTD_EDB7312 is not set
# CONFIG_ARCH_IQ31244 is not set
# CONFIG_ARCH_IQ80331 is not set
CONFIG_MACH_IQ80332=y
-# CONFIG_ARCH_EP80219 is not set
-
-#
-# IOP3xx Chipset Features
-#
-# CONFIG_IOP331_STEPD is not set
#
# Processor Type
#
# CONFIG_MTD_COMPLEX_MAPPINGS is not set
CONFIG_MTD_PHYSMAP=y
-CONFIG_MTD_PHYSMAP_START=0xc0000000
-CONFIG_MTD_PHYSMAP_LEN=0x00800000
+CONFIG_MTD_PHYSMAP_START=0x0
+CONFIG_MTD_PHYSMAP_LEN=0x0
CONFIG_MTD_PHYSMAP_BANKWIDTH=1
# CONFIG_MTD_ARM_INTEGRATOR is not set
# CONFIG_MTD_EDB7312 is not set
Say Y here if you want to run your kernel on the Intel IQ31244
evaluation kit for the IOP321 chipset.
-config ARCH_EP80219
- bool "Enable support for EP80219"
- select ARCH_IQ31244
- help
- Say Y here if you want to run your kernel on the Intel EP80219
- evaluation kit for the Intel 80219 chipset (a IOP321 variant).
-
endmenu
endif
# Makefile for the linux kernel.
#
-obj-y := common.o setup.o irq.o
+obj-y := irq.o
obj-m :=
obj-n :=
obj- :=
-obj-$(CONFIG_ARCH_IQ80321) += iq80321-mm.o iq80321-pci.o
-obj-$(CONFIG_ARCH_IQ31244) += iq31244-mm.o iq31244-pci.o
+obj-$(CONFIG_ARCH_IQ80321) += iq80321.o
+obj-$(CONFIG_ARCH_IQ31244) += iq31244.o
+++ /dev/null
-/*
- * arch/arm/mach-iop32x/common.c
- *
- * Common routines shared across all IOP3xx implementations
- *
- * Author: Deepak Saxena <dsaxena@mvista.com>
- *
- * Copyright 2003 (c) MontaVista, Software, Inc.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/delay.h>
-#include <asm/hardware.h>
-#include <asm/hardware/iop3xx.h>
-
-#ifdef CONFIG_ARCH_EP80219
-#include <linux/kernel.h>
-/*
- * Default power-off for EP80219
- */
-
-static inline void ep80219_send_to_pic(__u8 c) {
-}
-
-void ep80219_power_off(void)
-{
- /*
- * This function will send a SHUTDOWN_COMPLETE message to the PIC controller
- * over I2C. We are not using the i2c subsystem since we are going to power
- * off and it may be removed
- */
-
- /* Send the Address byte w/ the start condition */
- *IOP3XX_IDBR1 = 0x60;
- *IOP3XX_ICR1 = 0xE9;
- mdelay(1);
-
- /* Send the START_MSG byte w/ no start or stop condition */
- *IOP3XX_IDBR1 = 0x0F;
- *IOP3XX_ICR1 = 0xE8;
- mdelay(1);
-
- /* Send the SHUTDOWN_COMPLETE Message ID byte w/ no start or stop condition */
- *IOP3XX_IDBR1 = 0x03;
- *IOP3XX_ICR1 = 0xE8;
- mdelay(1);
-
- /* Send an ignored byte w/ stop condition */
- *IOP3XX_IDBR1 = 0x00;
- *IOP3XX_ICR1 = 0xEA;
-
- while (1) ;
-}
-
-#include <linux/init.h>
-#include <linux/pm.h>
-
-static int __init ep80219_init(void)
-{
- pm_power_off = ep80219_power_off;
- return 0;
-}
-arch_initcall(ep80219_init);
-#endif
+++ /dev/null
-/*
- * linux/arch/arm/mach-iop32x/iq31244-mm.c
- *
- * Low level memory initialization for iq80321 platform
- *
- * Author: Rory Bolt <rorybolt@pacbell.net>
- * Copyright (C) 2002 Rory Bolt
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- */
-
-#include <linux/mm.h>
-#include <linux/init.h>
-
-#include <asm/io.h>
-#include <asm/pgtable.h>
-#include <asm/page.h>
-
-#include <asm/mach/map.h>
-#include <asm/hardware/iop3xx.h>
-
-
-/*
- * IQ80321 specific IO mappings
- *
- * We use RedBoot's setup for the onboard devices.
- */
-static struct map_desc iq31244_io_desc[] __initdata = {
- { /* on-board devices */
- .virtual = IQ31244_UART,
- .pfn = __phys_to_pfn(IQ31244_UART),
- .length = 0x00100000,
- .type = MT_DEVICE
- }
-};
-
-void __init iq31244_map_io(void)
-{
- iop3xx_map_io();
-
- iotable_init(iq31244_io_desc, ARRAY_SIZE(iq31244_io_desc));
-}
+++ /dev/null
-/*
- * arch/arm/mach-iop32x/iq31244-pci.c
- *
- * PCI support for the Intel IQ31244 reference board
- *
- * Author: Rory Bolt <rorybolt@pacbell.net>
- * Copyright (C) 2002 Rory Bolt
- * Copyright (C) 2004 Intel Corp.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-#include <linux/kernel.h>
-#include <linux/pci.h>
-#include <linux/init.h>
-#include <linux/string.h>
-#include <linux/slab.h>
-
-#include <asm/hardware.h>
-#include <asm/irq.h>
-#include <asm/mach/pci.h>
-#include <asm/mach-types.h>
-
-/*
- * The following macro is used to lookup irqs in a standard table
- * format for those systems that do not already have PCI
- * interrupts properly routed. We assume 1 <= pin <= 4
- */
-#define PCI_IRQ_TABLE_LOOKUP(minid,maxid) \
-({ int _ctl_ = -1; \
- unsigned int _idsel = idsel - minid; \
- if (_idsel <= maxid) \
- _ctl_ = pci_irq_table[_idsel][pin-1]; \
- _ctl_; })
-
-#define INTA IRQ_IQ31244_INTA
-#define INTB IRQ_IQ31244_INTB
-#define INTC IRQ_IQ31244_INTC
-#define INTD IRQ_IQ31244_INTD
-
-#define INTE IRQ_IQ31244_I82546
-
-static inline int __init
-iq31244_map_irq(struct pci_dev *dev, u8 idsel, u8 pin)
-{
- static int pci_irq_table[][4] = {
- /*
- * PCI IDSEL/INTPIN->INTLINE
- * A B C D
- */
-#ifdef CONFIG_ARCH_EP80219
- {INTB, INTB, INTB, INTB}, /* CFlash */
- {INTE, INTE, INTE, INTE}, /* 82551 Pro 100 */
- {INTD, INTD, INTD, INTD}, /* PCI-X Slot */
- {INTC, INTC, INTC, INTC}, /* SATA */
-#else
- {INTB, INTB, INTB, INTB}, /* CFlash */
- {INTC, INTC, INTC, INTC}, /* SATA */
- {INTD, INTD, INTD, INTD}, /* PCI-X Slot */
- {INTE, INTE, INTE, INTE}, /* 82546 GigE */
-#endif // CONFIG_ARCH_EP80219
- };
-
- BUG_ON(pin < 1 || pin > 4);
-
- return PCI_IRQ_TABLE_LOOKUP(0, 7);
-}
-
-static struct hw_pci iq31244_pci __initdata = {
- .swizzle = pci_std_swizzle,
- .nr_controllers = 1,
- .setup = iop3xx_pci_setup,
- .scan = iop3xx_pci_scan_bus,
- .preinit = iop3xx_pci_preinit,
- .map_irq = iq31244_map_irq
-};
-
-static int __init iq31244_pci_init(void)
-{
- if (machine_is_iq31244())
- pci_common_init(&iq31244_pci);
- return 0;
-}
-
-subsys_initcall(iq31244_pci_init);
-
-
-
-
--- /dev/null
+/*
+ * arch/arm/mach-iop32x/iq31244.c
+ *
+ * Board support code for the Intel EP80219 and IQ31244 platforms.
+ *
+ * Author: Rory Bolt <rorybolt@pacbell.net>
+ * Copyright (C) 2002 Rory Bolt
+ * Copyright 2003 (c) MontaVista, Software, Inc.
+ * Copyright (C) 2004 Intel Corp.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/mm.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/pm.h>
+#include <linux/string.h>
+#include <linux/slab.h>
+#include <linux/serial_core.h>
+#include <linux/serial_8250.h>
+#include <linux/mtd/physmap.h>
+#include <linux/platform_device.h>
+#include <asm/hardware.h>
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/pci.h>
+#include <asm/mach/time.h>
+#include <asm/mach-types.h>
+#include <asm/page.h>
+#include <asm/pgtable.h>
+
+
+/*
+ * The EP80219 and IQ31244 use the same machine ID. To find out
+ * which of the two we're running on, we look at the processor ID.
+ */
+static int is_80219(void)
+{
+ extern int processor_id;
+ return !!((processor_id & 0xffffffe0) == 0x69052e20);
+}
+
+
+/*
+ * EP80219/IQ31244 timer tick configuration.
+ */
+static void __init iq31244_timer_init(void)
+{
+ if (is_80219()) {
+ /* 33.333 MHz crystal. */
+ iop3xx_init_time(200000000);
+ } else {
+ /* 33.000 MHz crystal. */
+ iop3xx_init_time(198000000);
+ }
+}
+
+static struct sys_timer iq31244_timer = {
+ .init = iq31244_timer_init,
+ .offset = iop3xx_gettimeoffset,
+};
+
+
+/*
+ * IQ31244 I/O.
+ */
+static struct map_desc iq31244_io_desc[] __initdata = {
+ { /* on-board devices */
+ .virtual = IQ31244_UART,
+ .pfn = __phys_to_pfn(IQ31244_UART),
+ .length = 0x00100000,
+ .type = MT_DEVICE,
+ },
+};
+
+void __init iq31244_map_io(void)
+{
+ iop3xx_map_io();
+ iotable_init(iq31244_io_desc, ARRAY_SIZE(iq31244_io_desc));
+}
+
+
+/*
+ * EP80219/IQ31244 PCI.
+ */
+static inline int __init
+ep80219_pci_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
+{
+ int irq;
+
+ if (slot == 0) {
+ /* CFlash */
+ irq = IRQ_IOP321_XINT1;
+ } else if (slot == 1) {
+ /* 82551 Pro 100 */
+ irq = IRQ_IOP321_XINT0;
+ } else if (slot == 2) {
+ /* PCI-X Slot */
+ irq = IRQ_IOP321_XINT3;
+ } else if (slot == 3) {
+ /* SATA */
+ irq = IRQ_IOP321_XINT2;
+ } else {
+ printk(KERN_ERR "ep80219_pci_map_irq() called for unknown "
+ "device PCI:%d:%d:%d\n", dev->bus->number,
+ PCI_SLOT(dev->devfn), PCI_FUNC(dev->devfn));
+ irq = -1;
+ }
+
+ return irq;
+}
+
+static struct hw_pci ep80219_pci __initdata = {
+ .swizzle = pci_std_swizzle,
+ .nr_controllers = 1,
+ .setup = iop3xx_pci_setup,
+ .preinit = iop3xx_pci_preinit,
+ .scan = iop3xx_pci_scan_bus,
+ .map_irq = ep80219_pci_map_irq,
+};
+
+static inline int __init
+iq31244_pci_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
+{
+ int irq;
+
+ if (slot == 0) {
+ /* CFlash */
+ irq = IRQ_IOP321_XINT1;
+ } else if (slot == 1) {
+ /* SATA */
+ irq = IRQ_IOP321_XINT2;
+ } else if (slot == 2) {
+ /* PCI-X Slot */
+ irq = IRQ_IOP321_XINT3;
+ } else if (slot == 3) {
+ /* 82546 GigE */
+ irq = IRQ_IOP321_XINT0;
+ } else {
+ printk(KERN_ERR "iq31244_pci_map_irq() called for unknown "
+ "device PCI:%d:%d:%d\n", dev->bus->number,
+ PCI_SLOT(dev->devfn), PCI_FUNC(dev->devfn));
+ irq = -1;
+ }
+
+ return irq;
+}
+
+static struct hw_pci iq31244_pci __initdata = {
+ .swizzle = pci_std_swizzle,
+ .nr_controllers = 1,
+ .setup = iop3xx_pci_setup,
+ .preinit = iop3xx_pci_preinit,
+ .scan = iop3xx_pci_scan_bus,
+ .map_irq = iq31244_pci_map_irq,
+};
+
+static int __init iq31244_pci_init(void)
+{
+ if (machine_is_iq31244()) {
+ if (is_80219()) {
+ pci_common_init(&ep80219_pci);
+ } else {
+ pci_common_init(&iq31244_pci);
+ }
+ }
+
+ return 0;
+}
+
+subsys_initcall(iq31244_pci_init);
+
+
+/*
+ * IQ31244 machine initialisation.
+ */
+static struct physmap_flash_data iq31244_flash_data = {
+ .width = 2,
+};
+
+static struct resource iq31244_flash_resource = {
+ .start = 0xf0000000,
+ .end = 0xf07fffff,
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device iq31244_flash_device = {
+ .name = "physmap-flash",
+ .id = 0,
+ .dev = {
+ .platform_data = &iq31244_flash_data,
+ },
+ .num_resources = 1,
+ .resource = &iq31244_flash_resource,
+};
+
+static struct plat_serial8250_port iq31244_serial_port[] = {
+ {
+ .mapbase = IQ31244_UART,
+ .membase = (char *)IQ31244_UART,
+ .irq = IRQ_IOP321_XINT1,
+ .flags = UPF_SKIP_TEST,
+ .iotype = UPIO_MEM,
+ .regshift = 0,
+ .uartclk = 1843200,
+ },
+ { },
+};
+
+static struct resource iq31244_uart_resource = {
+ .start = IQ31244_UART,
+ .end = IQ31244_UART + 7,
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device iq31244_serial_device = {
+ .name = "serial8250",
+ .id = PLAT8250_DEV_PLATFORM,
+ .dev = {
+ .platform_data = iq31244_serial_port,
+ },
+ .num_resources = 1,
+ .resource = &iq31244_uart_resource,
+};
+
+/*
+ * This function will send a SHUTDOWN_COMPLETE message to the PIC
+ * controller over I2C. We are not using the i2c subsystem since
+ * we are going to power off and it may be removed
+ */
+void ep80219_power_off(void)
+{
+ /*
+ * Send the Address byte w/ the start condition
+ */
+ *IOP3XX_IDBR1 = 0x60;
+ *IOP3XX_ICR1 = 0xE9;
+ mdelay(1);
+
+ /*
+ * Send the START_MSG byte w/ no start or stop condition
+ */
+ *IOP3XX_IDBR1 = 0x0F;
+ *IOP3XX_ICR1 = 0xE8;
+ mdelay(1);
+
+ /*
+ * Send the SHUTDOWN_COMPLETE Message ID byte w/ no start or
+ * stop condition
+ */
+ *IOP3XX_IDBR1 = 0x03;
+ *IOP3XX_ICR1 = 0xE8;
+ mdelay(1);
+
+ /*
+ * Send an ignored byte w/ stop condition
+ */
+ *IOP3XX_IDBR1 = 0x00;
+ *IOP3XX_ICR1 = 0xEA;
+
+ while (1)
+ ;
+}
+
+static void __init iq31244_init_machine(void)
+{
+ platform_device_register(&iop3xx_i2c0_device);
+ platform_device_register(&iop3xx_i2c1_device);
+ platform_device_register(&iq31244_flash_device);
+ platform_device_register(&iq31244_serial_device);
+
+ if (is_80219())
+ pm_power_off = ep80219_power_off;
+}
+
+MACHINE_START(IQ31244, "Intel IQ31244")
+ /* Maintainer: Intel Corp. */
+ .phys_io = IQ31244_UART,
+ .io_pg_offst = ((IQ31244_UART) >> 18) & 0xfffc,
+ .boot_params = 0xa0000100,
+ .map_io = iq31244_map_io,
+ .init_irq = iop321_init_irq,
+ .timer = &iq31244_timer,
+ .init_machine = iq31244_init_machine,
+MACHINE_END
+++ /dev/null
-/*
- * linux/arch/arm/mach-iop32x/iq80321-mm.c
- *
- * Low level memory initialization for iq80321 platform
- *
- * Author: Rory Bolt <rorybolt@pacbell.net>
- * Copyright (C) 2002 Rory Bolt
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- */
-
-#include <linux/mm.h>
-#include <linux/init.h>
-
-#include <asm/io.h>
-#include <asm/pgtable.h>
-#include <asm/page.h>
-
-#include <asm/mach/map.h>
-#include <asm/hardware/iop3xx.h>
-
-
-/*
- * IQ80321 specific IO mappings
- *
- * We use RedBoot's setup for the onboard devices.
- */
-static struct map_desc iq80321_io_desc[] __initdata = {
- { /* on-board devices */
- .virtual = IQ80321_UART,
- .pfn = __phys_to_pfn(IQ80321_UART),
- .length = 0x00100000,
- .type = MT_DEVICE
- }
-};
-
-void __init iq80321_map_io(void)
-{
- iop3xx_map_io();
-
- iotable_init(iq80321_io_desc, ARRAY_SIZE(iq80321_io_desc));
-}
+++ /dev/null
-/*
- * arch/arm/mach-iop32x/iq80321-pci.c
- *
- * PCI support for the Intel IQ80321 reference board
- *
- * Author: Rory Bolt <rorybolt@pacbell.net>
- * Copyright (C) 2002 Rory Bolt
- * Copyright (C) 2004 Intel Corp.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-#include <linux/kernel.h>
-#include <linux/pci.h>
-#include <linux/init.h>
-#include <linux/string.h>
-#include <linux/slab.h>
-
-#include <asm/hardware.h>
-#include <asm/irq.h>
-#include <asm/mach/pci.h>
-#include <asm/mach-types.h>
-
-/*
- * The following macro is used to lookup irqs in a standard table
- * format for those systems that do not already have PCI
- * interrupts properly routed. We assume 1 <= pin <= 4
- */
-#define PCI_IRQ_TABLE_LOOKUP(minid,maxid) \
-({ int _ctl_ = -1; \
- unsigned int _idsel = idsel - minid; \
- if (_idsel <= maxid) \
- _ctl_ = pci_irq_table[_idsel][pin-1]; \
- _ctl_; })
-
-#define INTA IRQ_IQ80321_INTA
-#define INTB IRQ_IQ80321_INTB
-#define INTC IRQ_IQ80321_INTC
-#define INTD IRQ_IQ80321_INTD
-
-#define INTE IRQ_IQ80321_I82544
-
-static inline int __init
-iq80321_map_irq(struct pci_dev *dev, u8 idsel, u8 pin)
-{
- static int pci_irq_table[][4] = {
- /*
- * PCI IDSEL/INTPIN->INTLINE
- * A B C D
- */
- {INTE, INTE, INTE, INTE}, /* Gig-E */
- {-1, -1, -1, -1}, /* Unused */
- {INTC, INTD, INTA, INTB}, /* PCI-X Slot */
- {-1, -1, -1, -1},
- };
-
- BUG_ON(pin < 1 || pin > 4);
-
-// return PCI_IRQ_TABLE_LOOKUP(4, 7);
- return pci_irq_table[idsel%4][pin-1];
-}
-
-static struct hw_pci iq80321_pci __initdata = {
- .swizzle = pci_std_swizzle,
- .nr_controllers = 1,
- .setup = iop3xx_pci_setup,
- .scan = iop3xx_pci_scan_bus,
- .preinit = iop3xx_pci_preinit,
- .map_irq = iq80321_map_irq
-};
-
-static int __init iq80321_pci_init(void)
-{
- if (machine_is_iq80321())
- pci_common_init(&iq80321_pci);
- return 0;
-}
-
-subsys_initcall(iq80321_pci_init);
-
-
-
-
--- /dev/null
+/*
+ * arch/arm/mach-iop32x/iq80321.c
+ *
+ * Board support code for the Intel IQ80321 platform.
+ *
+ * Author: Rory Bolt <rorybolt@pacbell.net>
+ * Copyright (C) 2002 Rory Bolt
+ * Copyright (C) 2004 Intel Corp.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/mm.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/string.h>
+#include <linux/slab.h>
+#include <linux/serial_core.h>
+#include <linux/serial_8250.h>
+#include <linux/mtd/physmap.h>
+#include <linux/platform_device.h>
+#include <asm/hardware.h>
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/pci.h>
+#include <asm/mach/time.h>
+#include <asm/mach-types.h>
+#include <asm/page.h>
+#include <asm/pgtable.h>
+
+/*
+ * IQ80321 timer tick configuration.
+ */
+static void __init iq80321_timer_init(void)
+{
+ /* 33.333 MHz crystal. */
+ iop3xx_init_time(200000000);
+}
+
+static struct sys_timer iq80321_timer = {
+ .init = iq80321_timer_init,
+ .offset = iop3xx_gettimeoffset,
+};
+
+
+/*
+ * IQ80321 I/O.
+ */
+static struct map_desc iq80321_io_desc[] __initdata = {
+ { /* on-board devices */
+ .virtual = IQ80321_UART,
+ .pfn = __phys_to_pfn(IQ80321_UART),
+ .length = 0x00100000,
+ .type = MT_DEVICE,
+ },
+};
+
+void __init iq80321_map_io(void)
+{
+ iop3xx_map_io();
+ iotable_init(iq80321_io_desc, ARRAY_SIZE(iq80321_io_desc));
+}
+
+
+/*
+ * IQ80321 PCI.
+ */
+static inline int __init
+iq80321_pci_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
+{
+ int irq;
+
+ if ((slot == 2 || slot == 6) && pin == 1) {
+ /* PCI-X Slot INTA */
+ irq = IRQ_IOP321_XINT2;
+ } else if ((slot == 2 || slot == 6) && pin == 2) {
+ /* PCI-X Slot INTA */
+ irq = IRQ_IOP321_XINT3;
+ } else if ((slot == 2 || slot == 6) && pin == 3) {
+ /* PCI-X Slot INTA */
+ irq = IRQ_IOP321_XINT0;
+ } else if ((slot == 2 || slot == 6) && pin == 4) {
+ /* PCI-X Slot INTA */
+ irq = IRQ_IOP321_XINT1;
+ } else if (slot == 4 || slot == 8) {
+ /* Gig-E */
+ irq = IRQ_IOP321_XINT0;
+ } else {
+ printk(KERN_ERR "iq80321_pci_map_irq() called for unknown "
+ "device PCI:%d:%d:%d\n", dev->bus->number,
+ PCI_SLOT(dev->devfn), PCI_FUNC(dev->devfn));
+ irq = -1;
+ }
+
+ return irq;
+}
+
+static struct hw_pci iq80321_pci __initdata = {
+ .swizzle = pci_std_swizzle,
+ .nr_controllers = 1,
+ .setup = iop3xx_pci_setup,
+ .preinit = iop3xx_pci_preinit,
+ .scan = iop3xx_pci_scan_bus,
+ .map_irq = iq80321_pci_map_irq,
+};
+
+static int __init iq80321_pci_init(void)
+{
+ if (machine_is_iq80321())
+ pci_common_init(&iq80321_pci);
+
+ return 0;
+}
+
+subsys_initcall(iq80321_pci_init);
+
+
+/*
+ * IQ80321 machine initialisation.
+ */
+static struct physmap_flash_data iq80321_flash_data = {
+ .width = 1,
+};
+
+static struct resource iq80321_flash_resource = {
+ .start = 0xf0000000,
+ .end = 0xf07fffff,
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device iq80321_flash_device = {
+ .name = "physmap-flash",
+ .id = 0,
+ .dev = {
+ .platform_data = &iq80321_flash_data,
+ },
+ .num_resources = 1,
+ .resource = &iq80321_flash_resource,
+};
+
+static struct plat_serial8250_port iq80321_serial_port[] = {
+ {
+ .mapbase = IQ80321_UART,
+ .membase = (char *)IQ80321_UART,
+ .irq = IRQ_IOP321_XINT1,
+ .flags = UPF_SKIP_TEST,
+ .iotype = UPIO_MEM,
+ .regshift = 0,
+ .uartclk = 1843200,
+ },
+ { },
+};
+
+static struct resource iq80321_uart_resource = {
+ .start = IQ80321_UART,
+ .end = IQ80321_UART + 7,
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device iq80321_serial_device = {
+ .name = "serial8250",
+ .id = PLAT8250_DEV_PLATFORM,
+ .dev = {
+ .platform_data = iq80321_serial_port,
+ },
+ .num_resources = 1,
+ .resource = &iq80321_uart_resource,
+};
+
+static void __init iq80321_init_machine(void)
+{
+ platform_device_register(&iop3xx_i2c0_device);
+ platform_device_register(&iop3xx_i2c1_device);
+ platform_device_register(&iq80321_flash_device);
+ platform_device_register(&iq80321_serial_device);
+}
+
+MACHINE_START(IQ80321, "Intel IQ80321")
+ /* Maintainer: Intel Corp. */
+ .phys_io = IQ80321_UART,
+ .io_pg_offst = ((IQ80321_UART) >> 18) & 0xfffc,
+ .boot_params = 0xa0000100,
+ .map_io = iq80321_map_io,
+ .init_irq = iop321_init_irq,
+ .timer = &iq80321_timer,
+ .init_machine = iq80321_init_machine,
+MACHINE_END
+++ /dev/null
-/*
- * linux/arch/arm/mach-iop32x/setup.c
- *
- * Author: Nicolas Pitre <nico@cam.org>
- * Copyright (C) 2001 MontaVista Software, Inc.
- * Copyright (C) 2004 Intel Corporation.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- */
-#include <linux/mm.h>
-#include <linux/init.h>
-#include <linux/major.h>
-#include <linux/fs.h>
-#include <linux/platform_device.h>
-#include <linux/serial.h>
-#include <linux/tty.h>
-#include <linux/serial_core.h>
-
-#include <asm/io.h>
-#include <asm/pgtable.h>
-#include <asm/page.h>
-#include <asm/mach/map.h>
-#include <asm/setup.h>
-#include <asm/system.h>
-#include <asm/memory.h>
-#include <asm/hardware.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-#include <asm/hardware/iop3xx.h>
-
-#define IOP321_UART_XTAL 1843200
-
-#ifdef CONFIG_ARCH_IQ80321
-#define UARTBASE IQ80321_UART
-#define IRQ_UART IRQ_IQ80321_UART
-#endif
-
-#ifdef CONFIG_ARCH_IQ31244
-#define UARTBASE IQ31244_UART
-#define IRQ_UART IRQ_IQ31244_UART
-#endif
-
-static struct uart_port iop321_serial_ports[] = {
- {
- .membase = (char*)(UARTBASE),
- .mapbase = (UARTBASE),
- .irq = IRQ_UART,
- .flags = UPF_SKIP_TEST,
- .iotype = UPIO_MEM,
- .regshift = 0,
- .uartclk = IOP321_UART_XTAL,
- .line = 0,
- .type = PORT_16550A,
- .fifosize = 16
- }
-};
-
-void __init iop32x_init(void)
-{
- platform_device_register(&iop3xx_i2c0_device);
- platform_device_register(&iop3xx_i2c1_device);
- early_serial_setup(&iop321_serial_ports[0]);
-}
-
-#ifdef CONFIG_ARCH_IQ80321
-extern void iq80321_map_io(void);
-#endif
-
-#ifdef CONFIG_ARCH_IQ31244
-extern void iq31244_map_io(void);
-#endif
-
-static void __init iop3xx_timer_init(void)
-{
- iop3xx_init_time(IOP321_TICK_RATE);
-}
-
-struct sys_timer iop321_timer = {
- .init = iop3xx_timer_init,
- .offset = iop3xx_gettimeoffset,
-};
-
-#if defined(CONFIG_ARCH_IQ80321)
-MACHINE_START(IQ80321, "Intel IQ80321")
- /* Maintainer: Intel Corporation */
- .phys_io = IQ80321_UART,
- .io_pg_offst = ((IQ80321_UART) >> 18) & 0xfffc,
- .map_io = iq80321_map_io,
- .init_irq = iop321_init_irq,
- .timer = &iop321_timer,
- .boot_params = 0xa0000100,
- .init_machine = iop32x_init,
-MACHINE_END
-#elif defined(CONFIG_ARCH_IQ31244)
-MACHINE_START(IQ31244, "Intel IQ31244")
- /* Maintainer: Intel Corp. */
- .phys_io = IQ31244_UART,
- .io_pg_offst = ((IQ31244_UART) >> 18) & 0xfffc,
- .map_io = iq31244_map_io,
- .init_irq = iop321_init_irq,
- .timer = &iop321_timer,
- .boot_params = 0xa0000100,
- .init_machine = iop32x_init,
-MACHINE_END
-#else
-#error No machine descriptor defined for this IOP3XX implementation
-#endif
Say Y here if you want to run your kernel on the Intel IQ80332
evaluation kit for the IOP332 chipset.
-config IOP331_STEPD
- bool "Chip stepping D of the IOP80331 processor or IOP80333"
- help
- Say Y here if you have StepD of the IOP80331 or IOP8033
- based platforms.
-
endmenu
endif
# Makefile for the linux kernel.
#
-obj-y := setup.o irq.o
+obj-y := irq.o uart.o
obj-m :=
obj-n :=
obj- :=
-obj-$(CONFIG_ARCH_IQ80331) += iq80331-pci.o
-obj-$(CONFIG_MACH_IQ80332) += iq80332-pci.o
+obj-$(CONFIG_ARCH_IQ80331) += iq80331.o
+obj-$(CONFIG_MACH_IQ80332) += iq80332.o
+++ /dev/null
-/*
- * arch/arm/mach-iop33x/iq80331-pci.c
- *
- * PCI support for the Intel IQ80331 reference board
- *
- * Author: Dave Jiang <dave.jiang@intel.com>
- * Copyright (C) 2003, 2004 Intel Corp.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-#include <linux/kernel.h>
-#include <linux/pci.h>
-#include <linux/init.h>
-#include <linux/string.h>
-#include <linux/slab.h>
-
-#include <asm/hardware.h>
-#include <asm/irq.h>
-#include <asm/mach/pci.h>
-#include <asm/mach-types.h>
-
-/*
- * The following macro is used to lookup irqs in a standard table
- * format for those systems that do not already have PCI
- * interrupts properly routed. We assume 1 <= pin <= 4
- */
-#define PCI_IRQ_TABLE_LOOKUP(minid,maxid) \
-({ int _ctl_ = -1; \
- unsigned int _idsel = idsel - minid; \
- if (_idsel <= maxid) \
- _ctl_ = pci_irq_table[_idsel][pin-1]; \
- _ctl_; })
-
-#define INTA IRQ_IQ80331_INTA
-#define INTB IRQ_IQ80331_INTB
-#define INTC IRQ_IQ80331_INTC
-#define INTD IRQ_IQ80331_INTD
-
-//#define INTE IRQ_IQ80331_I82544
-
-static inline int __init
-iq80331_map_irq(struct pci_dev *dev, u8 idsel, u8 pin)
-{
- static int pci_irq_table[][4] = {
- /*
- * PCI IDSEL/INTPIN->INTLINE
- * A B C D
- */
- {INTB, INTC, INTD, INTA}, /* PCI-X Slot */
- {INTC, INTC, INTC, INTC}, /* GigE */
- };
-
- BUG_ON(pin < 1 || pin > 4);
-
- return PCI_IRQ_TABLE_LOOKUP(1, 7);
-}
-
-static struct hw_pci iq80331_pci __initdata = {
- .swizzle = pci_std_swizzle,
- .nr_controllers = 1,
- .setup = iop3xx_pci_setup,
- .scan = iop3xx_pci_scan_bus,
- .preinit = iop3xx_pci_preinit,
- .map_irq = iq80331_map_irq
-};
-
-static int __init iq80331_pci_init(void)
-{
- if (machine_is_iq80331())
- pci_common_init(&iq80331_pci);
- return 0;
-}
-
-subsys_initcall(iq80331_pci_init);
-
-
-
-
--- /dev/null
+/*
+ * arch/arm/mach-iop33x/iq80331.c
+ *
+ * Board support code for the Intel IQ80331 platform.
+ *
+ * Author: Dave Jiang <dave.jiang@intel.com>
+ * Copyright (C) 2003 Intel Corp.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/mm.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/string.h>
+#include <linux/slab.h>
+#include <linux/serial_core.h>
+#include <linux/serial_8250.h>
+#include <linux/mtd/physmap.h>
+#include <linux/platform_device.h>
+#include <asm/hardware.h>
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/pci.h>
+#include <asm/mach/time.h>
+#include <asm/mach-types.h>
+#include <asm/page.h>
+#include <asm/pgtable.h>
+
+/*
+ * IQ80331 timer tick configuration.
+ */
+static void __init iq80331_timer_init(void)
+{
+ /* D-Step parts run at a higher internal bus frequency */
+ if (*IOP3XX_ATURID >= 0xa)
+ iop3xx_init_time(333000000);
+ else
+ iop3xx_init_time(266000000);
+}
+
+static struct sys_timer iq80331_timer = {
+ .init = iq80331_timer_init,
+ .offset = iop3xx_gettimeoffset,
+};
+
+
+/*
+ * IQ80331 PCI.
+ */
+static inline int __init
+iq80331_pci_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
+{
+ int irq;
+
+ if (slot == 1 && pin == 1) {
+ /* PCI-X Slot INTA */
+ irq = IRQ_IOP331_XINT1;
+ } else if (slot == 1 && pin == 2) {
+ /* PCI-X Slot INTB */
+ irq = IRQ_IOP331_XINT2;
+ } else if (slot == 1 && pin == 3) {
+ /* PCI-X Slot INTC */
+ irq = IRQ_IOP331_XINT3;
+ } else if (slot == 1 && pin == 4) {
+ /* PCI-X Slot INTD */
+ irq = IRQ_IOP331_XINT0;
+ } else if (slot == 2) {
+ /* GigE */
+ irq = IRQ_IOP331_XINT2;
+ } else {
+ printk(KERN_ERR "iq80331_pci_map_irq() called for unknown "
+ "device PCI:%d:%d:%d\n", dev->bus->number,
+ PCI_SLOT(dev->devfn), PCI_FUNC(dev->devfn));
+ irq = -1;
+ }
+
+ return irq;
+}
+
+static struct hw_pci iq80331_pci __initdata = {
+ .swizzle = pci_std_swizzle,
+ .nr_controllers = 1,
+ .setup = iop3xx_pci_setup,
+ .preinit = iop3xx_pci_preinit,
+ .scan = iop3xx_pci_scan_bus,
+ .map_irq = iq80331_pci_map_irq,
+};
+
+static int __init iq80331_pci_init(void)
+{
+ if (machine_is_iq80331())
+ pci_common_init(&iq80331_pci);
+
+ return 0;
+}
+
+subsys_initcall(iq80331_pci_init);
+
+
+/*
+ * IQ80331 machine initialisation.
+ */
+static struct physmap_flash_data iq80331_flash_data = {
+ .width = 1,
+};
+
+static struct resource iq80331_flash_resource = {
+ .start = 0xc0000000,
+ .end = 0xc07fffff,
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device iq80331_flash_device = {
+ .name = "physmap-flash",
+ .id = 0,
+ .dev = {
+ .platform_data = &iq80331_flash_data,
+ },
+ .num_resources = 1,
+ .resource = &iq80331_flash_resource,
+};
+
+static void __init iq80331_init_machine(void)
+{
+ platform_device_register(&iop3xx_i2c0_device);
+ platform_device_register(&iop3xx_i2c1_device);
+ platform_device_register(&iop33x_uart0_device);
+ platform_device_register(&iop33x_uart1_device);
+ platform_device_register(&iq80331_flash_device);
+}
+
+MACHINE_START(IQ80331, "Intel IQ80331")
+ /* Maintainer: Intel Corp. */
+ .phys_io = 0xfefff000,
+ .io_pg_offst = ((0xfffff000) >> 18) & 0xfffc,
+ .boot_params = 0x00000100,
+ .map_io = iop3xx_map_io,
+ .init_irq = iop331_init_irq,
+ .timer = &iq80331_timer,
+ .init_machine = iq80331_init_machine,
+MACHINE_END
+++ /dev/null
-/*
- * arch/arm/mach-iop33x/iq80332-pci.c
- *
- * PCI support for the Intel IQ80332 reference board
- *
- * Author: Dave Jiang <dave.jiang@intel.com>
- * Copyright (C) 2004 Intel Corp.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-#include <linux/kernel.h>
-#include <linux/pci.h>
-#include <linux/init.h>
-#include <linux/string.h>
-#include <linux/slab.h>
-
-#include <asm/hardware.h>
-#include <asm/irq.h>
-#include <asm/mach/pci.h>
-#include <asm/mach-types.h>
-
-/*
- * The following macro is used to lookup irqs in a standard table
- * format for those systems that do not already have PCI
- * interrupts properly routed. We assume 1 <= pin <= 4
- */
-#define PCI_IRQ_TABLE_LOOKUP(minid,maxid) \
-({ int _ctl_ = -1; \
- unsigned int _idsel = idsel - minid; \
- if (_idsel <= maxid) \
- _ctl_ = pci_irq_table[_idsel][pin-1]; \
- _ctl_; })
-
-#define INTA IRQ_IQ80332_INTA
-#define INTB IRQ_IQ80332_INTB
-#define INTC IRQ_IQ80332_INTC
-#define INTD IRQ_IQ80332_INTD
-
-//#define INTE IRQ_IQ80332_I82544
-
-static inline int __init
-iq80332_map_irq(struct pci_dev *dev, u8 idsel, u8 pin)
-{
- static int pci_irq_table[][8] = {
- /*
- * PCI IDSEL/INTPIN->INTLINE
- * A B C D
- */
- {-1, -1, -1, -1},
- {-1, -1, -1, -1},
- {-1, -1, -1, -1},
- {INTA, INTB, INTC, INTD}, /* PCI-X Slot */
- {-1, -1, -1, -1},
- {INTC, INTC, INTC, INTC}, /* GigE */
- {-1, -1, -1, -1},
- {-1, -1, -1, -1},
- };
-
- BUG_ON(pin < 1 || pin > 4);
-
- return PCI_IRQ_TABLE_LOOKUP(1, 7);
-}
-
-static struct hw_pci iq80332_pci __initdata = {
- .swizzle = pci_std_swizzle,
- .nr_controllers = 1,
- .setup = iop3xx_pci_setup,
- .scan = iop3xx_pci_scan_bus,
- .preinit = iop3xx_pci_preinit,
- .map_irq = iq80332_map_irq
-};
-
-static int __init iq80332_pci_init(void)
-{
- if (machine_is_iq80332())
- pci_common_init(&iq80332_pci);
- return 0;
-}
-
-subsys_initcall(iq80332_pci_init);
-
-
-
-
--- /dev/null
+/*
+ * arch/arm/mach-iop33x/iq80332.c
+ *
+ * Board support code for the Intel IQ80332 platform.
+ *
+ * Author: Dave Jiang <dave.jiang@intel.com>
+ * Copyright (C) 2004 Intel Corp.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/mm.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/string.h>
+#include <linux/slab.h>
+#include <linux/serial_core.h>
+#include <linux/serial_8250.h>
+#include <linux/mtd/physmap.h>
+#include <linux/platform_device.h>
+#include <asm/hardware.h>
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/pci.h>
+#include <asm/mach/time.h>
+#include <asm/mach-types.h>
+#include <asm/page.h>
+#include <asm/pgtable.h>
+
+/*
+ * IQ80332 timer tick configuration.
+ */
+static void __init iq80332_timer_init(void)
+{
+ /* D-Step parts and the iop333 run at a higher internal bus frequency */
+ if (*IOP3XX_ATURID >= 0xa || *IOP3XX_ATUDID == 0x374)
+ iop3xx_init_time(333000000);
+ else
+ iop3xx_init_time(266000000);
+}
+
+static struct sys_timer iq80332_timer = {
+ .init = iq80332_timer_init,
+ .offset = iop3xx_gettimeoffset,
+};
+
+
+/*
+ * IQ80332 PCI.
+ */
+static inline int __init
+iq80332_pci_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
+{
+ int irq;
+
+ if (slot == 4 && pin == 1) {
+ /* PCI-X Slot INTA */
+ irq = IRQ_IOP331_XINT0;
+ } else if (slot == 4 && pin == 2) {
+ /* PCI-X Slot INTB */
+ irq = IRQ_IOP331_XINT1;
+ } else if (slot == 4 && pin == 3) {
+ /* PCI-X Slot INTC */
+ irq = IRQ_IOP331_XINT2;
+ } else if (slot == 4 && pin == 4) {
+ /* PCI-X Slot INTD */
+ irq = IRQ_IOP331_XINT3;
+ } else if (slot == 6) {
+ /* GigE */
+ irq = IRQ_IOP331_XINT2;
+ } else {
+ printk(KERN_ERR "iq80332_pci_map_irq() called for unknown "
+ "device PCI:%d:%d:%d\n", dev->bus->number,
+ PCI_SLOT(dev->devfn), PCI_FUNC(dev->devfn));
+ irq = -1;
+ }
+
+ return irq;
+}
+
+static struct hw_pci iq80332_pci __initdata = {
+ .swizzle = pci_std_swizzle,
+ .nr_controllers = 1,
+ .setup = iop3xx_pci_setup,
+ .preinit = iop3xx_pci_preinit,
+ .scan = iop3xx_pci_scan_bus,
+ .map_irq = iq80332_pci_map_irq,
+};
+
+static int __init iq80332_pci_init(void)
+{
+ if (machine_is_iq80332())
+ pci_common_init(&iq80332_pci);
+
+ return 0;
+}
+
+subsys_initcall(iq80332_pci_init);
+
+
+/*
+ * IQ80332 machine initialisation.
+ */
+static struct physmap_flash_data iq80332_flash_data = {
+ .width = 1,
+};
+
+static struct resource iq80332_flash_resource = {
+ .start = 0xc0000000,
+ .end = 0xc07fffff,
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device iq80332_flash_device = {
+ .name = "physmap-flash",
+ .id = 0,
+ .dev = {
+ .platform_data = &iq80332_flash_data,
+ },
+ .num_resources = 1,
+ .resource = &iq80332_flash_resource,
+};
+
+static void __init iq80332_init_machine(void)
+{
+ platform_device_register(&iop3xx_i2c0_device);
+ platform_device_register(&iop3xx_i2c1_device);
+ platform_device_register(&iop33x_uart0_device);
+ platform_device_register(&iop33x_uart1_device);
+ platform_device_register(&iq80332_flash_device);
+}
+
+MACHINE_START(IQ80332, "Intel IQ80332")
+ /* Maintainer: Intel Corp. */
+ .phys_io = 0xfefff000,
+ .io_pg_offst = ((0xfffff000) >> 18) & 0xfffc,
+ .boot_params = 0x00000100,
+ .map_io = iop3xx_map_io,
+ .init_irq = iop331_init_irq,
+ .timer = &iq80332_timer,
+ .init_machine = iq80332_init_machine,
+MACHINE_END
+++ /dev/null
-/*
- * linux/arch/arm/mach-iop33x/setup.c
- *
- * Author: Dave Jiang (dave.jiang@intel.com)
- * Copyright (C) 2004 Intel Corporation.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- */
-#include <linux/mm.h>
-#include <linux/init.h>
-#include <linux/major.h>
-#include <linux/fs.h>
-#include <linux/platform_device.h>
-#include <linux/serial.h>
-#include <linux/tty.h>
-#include <linux/serial_8250.h>
-
-#include <asm/io.h>
-#include <asm/pgtable.h>
-#include <asm/page.h>
-#include <asm/mach/map.h>
-#include <asm/setup.h>
-#include <asm/system.h>
-#include <asm/memory.h>
-#include <asm/hardware.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-#include <asm/hardware/iop3xx.h>
-
-#define IOP331_UART_XTAL 33334000
-
-static struct resource iop33x_uart0_resources[] = {
- [0] = {
- .start = IOP331_UART0_PHYS,
- .end = IOP331_UART0_PHYS + 0x3f,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = IRQ_IOP331_UART0,
- .end = IRQ_IOP331_UART0,
- .flags = IORESOURCE_IRQ
- }
-};
-
-static struct resource iop33x_uart1_resources[] = {
- [0] = {
- .start = IOP331_UART1_PHYS,
- .end = IOP331_UART1_PHYS + 0x3f,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = IRQ_IOP331_UART1,
- .end = IRQ_IOP331_UART1,
- .flags = IORESOURCE_IRQ
- }
-};
-
-static struct plat_serial8250_port iop33x_uart0_data[] = {
- {
- .membase = (char*)(IOP331_UART0_VIRT),
- .mapbase = (IOP331_UART0_PHYS),
- .irq = IRQ_IOP331_UART0,
- .uartclk = IOP331_UART_XTAL,
- .regshift = 2,
- .iotype = UPIO_MEM,
- .flags = UPF_SKIP_TEST,
- },
- { },
-};
-
-static struct plat_serial8250_port iop33x_uart1_data[] = {
- {
- .membase = (char*)(IOP331_UART1_VIRT),
- .mapbase = (IOP331_UART1_PHYS),
- .irq = IRQ_IOP331_UART1,
- .uartclk = IOP331_UART_XTAL,
- .regshift = 2,
- .iotype = UPIO_MEM,
- .flags = UPF_SKIP_TEST,
- },
- { },
-};
-
-static struct platform_device iop33x_uart0 = {
- .name = "serial8250",
- .id = PLAT8250_DEV_PLATFORM,
- .dev.platform_data = iop33x_uart0_data,
- .num_resources = 2,
- .resource = iop33x_uart0_resources,
-};
-
-static struct platform_device iop33x_uart1 = {
- .name = "serial8250",
- .id = PLAT8250_DEV_PLATFORM1,
- .dev.platform_data = iop33x_uart1_data,
- .num_resources = 2,
- .resource = iop33x_uart1_resources,
-};
-
-static struct platform_device *iop33x_devices[] __initdata = {
- &iop33x_uart0,
- &iop33x_uart1,
-};
-
-void __init iop33x_init(void)
-{
- if(iop_is_331())
- {
- platform_add_devices(iop33x_devices,
- ARRAY_SIZE(iop33x_devices));
- }
- platform_device_register(&iop3xx_i2c0_device);
- platform_device_register(&iop3xx_i2c1_device);
-}
-
-#ifdef CONFIG_ARCH_IOP33X
-extern void iop331_init_irq(void);
-#endif
-
-static void __init iop3xx_timer_init(void)
-{
- iop3xx_init_time(IOP331_TICK_RATE);
-}
-
-struct sys_timer iop331_timer = {
- .init = iop3xx_timer_init,
- .offset = iop3xx_gettimeoffset,
-};
-
-#if defined(CONFIG_ARCH_IQ80331)
-MACHINE_START(IQ80331, "Intel IQ80331")
- /* Maintainer: Intel Corp. */
- .phys_io = 0xfefff000,
- .io_pg_offst = ((0xfffff000) >> 18) & 0xfffc, // virtual, physical
- .map_io = iop3xx_map_io,
- .init_irq = iop331_init_irq,
- .timer = &iop331_timer,
- .boot_params = 0x0100,
- .init_machine = iop33x_init,
-MACHINE_END
-
-#elif defined(CONFIG_MACH_IQ80332)
-MACHINE_START(IQ80332, "Intel IQ80332")
- /* Maintainer: Intel Corp. */
- .phys_io = 0xfefff000,
- .io_pg_offst = ((0xfffff000) >> 18) & 0xfffc, // virtual, physical
- .map_io = iop3xx_map_io,
- .init_irq = iop331_init_irq,
- .timer = &iop331_timer,
- .boot_params = 0x0100,
- .init_machine = iop33x_init,
-MACHINE_END
-
-#else
-#error No machine descriptor defined for this IOP3XX implementation
-#endif
-
-
--- /dev/null
+/*
+ * linux/arch/arm/mach-iop33x/uart.c
+ *
+ * Author: Dave Jiang (dave.jiang@intel.com)
+ * Copyright (C) 2004 Intel Corporation.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/mm.h>
+#include <linux/init.h>
+#include <linux/major.h>
+#include <linux/fs.h>
+#include <linux/platform_device.h>
+#include <linux/serial.h>
+#include <linux/tty.h>
+#include <linux/serial_8250.h>
+
+#include <asm/io.h>
+#include <asm/pgtable.h>
+#include <asm/page.h>
+#include <asm/mach/map.h>
+#include <asm/setup.h>
+#include <asm/system.h>
+#include <asm/memory.h>
+#include <asm/hardware.h>
+#include <asm/hardware/iop3xx.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+
+#define IOP331_UART_XTAL 33334000
+
+static struct plat_serial8250_port iop33x_uart0_data[] = {
+ {
+ .membase = (char *)IOP331_UART0_VIRT,
+ .mapbase = IOP331_UART0_PHYS,
+ .irq = IRQ_IOP331_UART0,
+ .uartclk = IOP331_UART_XTAL,
+ .regshift = 2,
+ .iotype = UPIO_MEM,
+ .flags = UPF_SKIP_TEST,
+ },
+ { },
+};
+
+static struct resource iop33x_uart0_resources[] = {
+ [0] = {
+ .start = IOP331_UART0_PHYS,
+ .end = IOP331_UART0_PHYS + 0x3f,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = IRQ_IOP331_UART0,
+ .end = IRQ_IOP331_UART0,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+struct platform_device iop33x_uart0_device = {
+ .name = "serial8250",
+ .id = PLAT8250_DEV_PLATFORM,
+ .dev = {
+ .platform_data = iop33x_uart0_data,
+ },
+ .num_resources = 2,
+ .resource = iop33x_uart0_resources,
+};
+
+
+static struct resource iop33x_uart1_resources[] = {
+ [0] = {
+ .start = IOP331_UART1_PHYS,
+ .end = IOP331_UART1_PHYS + 0x3f,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = IRQ_IOP331_UART1,
+ .end = IRQ_IOP331_UART1,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct plat_serial8250_port iop33x_uart1_data[] = {
+ {
+ .membase = (char *)IOP331_UART1_VIRT,
+ .mapbase = IOP331_UART1_PHYS,
+ .irq = IRQ_IOP331_UART1,
+ .uartclk = IOP331_UART_XTAL,
+ .regshift = 2,
+ .iotype = UPIO_MEM,
+ .flags = UPF_SKIP_TEST,
+ },
+ { },
+};
+
+struct platform_device iop33x_uart1_device = {
+ .name = "serial8250",
+ .id = PLAT8250_DEV_PLATFORM1,
+ .dev = {
+ .platform_data = iop33x_uart1_data,
+ },
+ .num_resources = 2,
+ .resource = iop33x_uart1_resources,
+};
#define IOP321_IINTSRC (volatile u32 *)IOP321_REG_ADDR(0x000007D8)
#define IOP321_FINTSRC (volatile u32 *)IOP321_REG_ADDR(0x000007DC)
-/* Timers */
-#ifdef CONFIG_ARCH_IQ80321
-#define IOP321_TICK_RATE 200000000 /* 200 MHz clock */
-#elif defined(CONFIG_ARCH_IQ31244)
-#define IOP321_TICK_RATE 198000000 /* 33.000 MHz crystal */
-#endif
-
-#ifdef CONFIG_ARCH_EP80219
-#undef IOP321_TICK_RATE
-#define IOP321_TICK_RATE 200000000 /* 33.333333 Mhz crystal */
-#endif
-
/* Application accelerator unit 0x00000800 - 0x000008FF */
#define IOP321_AAU_ACR (volatile u32 *)IOP321_REG_ADDR(0x00000800)
#define IOP321_AAU_ASR (volatile u32 *)IOP321_REG_ADDR(0x00000804)
#ifndef _IQ31244_H_
#define _IQ31244_H_
-#define IQ31244_FLASHBASE 0xf0000000 /* Flash */
-#define IQ31244_FLASHSIZE 0x00800000
-#define IQ31244_FLASHWIDTH 2
-
#define IQ31244_UART 0xfe800000 /* UART #1 */
#define IQ31244_7SEG_1 0xfe840000 /* 7-Segment MSB */
#define IQ31244_7SEG_0 0xfe850000 /* 7-Segment LSB (WO) */
#define IQ31244_ROTARY_SW 0xfe8d0000 /* Rotary Switch */
#define IQ31244_BATT_STAT 0xfe8f0000 /* Battery Status */
-#ifndef __ASSEMBLY__
-extern void iq31244_map_io(void);
-#endif
#endif // _IQ31244_H_
#ifndef _IQ80321_H_
#define _IQ80321_H_
-#define IQ80321_FLASHBASE 0xf0000000 /* Flash */
-#define IQ80321_FLASHSIZE 0x00800000
-#define IQ80321_FLASHWIDTH 1
-
#define IQ80321_UART 0xfe800000 /* UART #1 */
#define IQ80321_7SEG_1 0xfe840000 /* 7-Segment MSB */
#define IQ80321_7SEG_0 0xfe850000 /* 7-Segment LSB (WO) */
#define IQ80321_ROTARY_SW 0xfe8d0000 /* Rotary Switch */
#define IQ80321_BATT_STAT 0xfe8f0000 /* Battery Status */
-#ifndef __ASSEMBLY__
-extern void iq80321_map_io(void);
-#endif
#endif // _IQ80321_H_
#define NR_IRQS 32
-/*
- * Interrupts available on the IQ80321 board
- */
-
-/*
- * On board devices
- */
-#define IRQ_IQ80321_I82544 IRQ_IOP321_XINT0
-#define IRQ_IQ80321_UART IRQ_IOP321_XINT1
-
-/*
- * PCI interrupts
- */
-#define IRQ_IQ80321_INTA IRQ_IOP321_XINT0
-#define IRQ_IQ80321_INTB IRQ_IOP321_XINT1
-#define IRQ_IQ80321_INTC IRQ_IOP321_XINT2
-#define IRQ_IQ80321_INTD IRQ_IOP321_XINT3
-
-/*
- * Interrupts on the IQ31244 board
- */
-
-/*
- * On board devices
- */
-#define IRQ_IQ31244_UART IRQ_IOP321_XINT1
-#define IRQ_IQ31244_I82546 IRQ_IOP321_XINT0
-#define IRQ_IQ31244_SATA IRQ_IOP321_XINT2
-#define IRQ_IQ31244_PCIX_SLOT IRQ_IOP321_XINT3
-
-/*
- * PCI interrupts
- */
-#define IRQ_IQ31244_INTA IRQ_IOP321_XINT0
-#define IRQ_IQ31244_INTB IRQ_IOP321_XINT1
-#define IRQ_IQ31244_INTC IRQ_IOP321_XINT2
-#define IRQ_IQ31244_INTD IRQ_IOP321_XINT3
-
#endif // _IRQ_H_
#define PCIBIOS_MIN_IO 0x00000000
#define PCIBIOS_MIN_MEM 0x00000000
+#ifndef __ASSEMBLY__
+extern struct platform_device iop33x_uart0_device;
+extern struct platform_device iop33x_uart1_device;
+#endif
+
/*
* Generic chipset bits
#define IOP331_FINTVEC (volatile u32 *)IOP331_REG_ADDR(0x000007CC)
-/* Timers */
-#if defined(CONFIG_ARCH_IOP33X)
-#define IOP331_TICK_RATE 266000000 /* 266 MHz IB clock */
-#endif
-
-#if defined(CONFIG_IOP331_STEPD) || defined(CONFIG_ARCH_IQ80333)
-#undef IOP331_TICK_RATE
-#define IOP331_TICK_RATE 333000000 /* 333 Mhz IB clock */
-#endif
-
/* Application accelerator unit 0x00000800 - 0x000008FF */
#define IOP331_AAU_ACR (volatile u32 *)IOP331_REG_ADDR(0x00000800)
#define IOP331_AAU_ASR (volatile u32 *)IOP331_REG_ADDR(0x00000804)
#ifndef _IQ80331_H_
#define _IQ80331_H_
-#define IQ80331_FLASHBASE 0xc0000000 /* Flash */
-#define IQ80331_FLASHSIZE 0x00800000
-#define IQ80331_FLASHWIDTH 1
-
#define IQ80331_7SEG_1 0xce840000 /* 7-Segment MSB */
#define IQ80331_7SEG_0 0xce850000 /* 7-Segment LSB (WO) */
#define IQ80331_ROTARY_SW 0xce8d0000 /* Rotary Switch */
#define IQ80331_BATT_STAT 0xce8f0000 /* Battery Status */
-#ifndef __ASSEMBLY__
-extern void iq80331_map_io(void);
-#endif
#endif // _IQ80331_H_
#ifndef _IQ80332_H_
#define _IQ80332_H_
-#define IQ80332_FLASHBASE 0xc0000000 /* Flash */
-#define IQ80332_FLASHSIZE 0x00800000
-#define IQ80332_FLASHWIDTH 1
-
#define IQ80332_7SEG_1 0xce840000 /* 7-Segment MSB */
#define IQ80332_7SEG_0 0xce850000 /* 7-Segment LSB (WO) */
#define IQ80332_ROTARY_SW 0xce8d0000 /* Rotary Switch */
#define IQ80332_BATT_STAT 0xce8f0000 /* Battery Status */
-#ifndef __ASSEMBLY__
-extern void iq80332_map_io(void);
-#endif
#endif // _IQ80332_H_
#define NR_IRQS 64
-/*
- * Interrupts available on the IQ80331 board
- */
-
-/*
- * On board devices
- */
-#define IRQ_IQ80331_I82544 IRQ_IOP331_XINT0
-#define IRQ_IQ80331_UART0 IRQ_IOP331_UART0
-#define IRQ_IQ80331_UART1 IRQ_IOP331_UART1
-
-/*
- * PCI interrupts
- */
-#define IRQ_IQ80331_INTA IRQ_IOP331_XINT0
-#define IRQ_IQ80331_INTB IRQ_IOP331_XINT1
-#define IRQ_IQ80331_INTC IRQ_IOP331_XINT2
-#define IRQ_IQ80331_INTD IRQ_IOP331_XINT3
-
-/*
- * Interrupts available on the IQ80332 board
- */
-
-/*
- * On board devices
- */
-#define IRQ_IQ80332_I82544 IRQ_IOP331_XINT0
-#define IRQ_IQ80332_UART0 IRQ_IOP331_UART0
-#define IRQ_IQ80332_UART1 IRQ_IOP331_UART1
-
-/*
- * PCI interrupts
- */
-#define IRQ_IQ80332_INTA IRQ_IOP331_XINT0
-#define IRQ_IQ80332_INTB IRQ_IOP331_XINT1
-#define IRQ_IQ80332_INTC IRQ_IOP331_XINT2
-#define IRQ_IQ80332_INTD IRQ_IOP331_XINT3
-
#endif // _IRQ_H_
git.samba.org / sfrench / cifs-2.6.git / commitdiff