Copyright (C) 2004 BULL SA.
Written by Simon.Derr@bull.net
-Portions Copyright (c) 2004 Silicon Graphics, Inc.
+Portions Copyright (c) 2004-2006 Silicon Graphics, Inc.
Modified by Paul Jackson <pj@sgi.com>
+Modified by Christoph Lameter <clameter@sgi.com>
CONTENTS:
=========
These subsets, or "soft partitions" must be able to be dynamically
adjusted, as the job mix changes, without impacting other concurrently
-executing jobs.
+executing jobs. The location of the running jobs pages may also be moved
+when the memory locations are changed.
The kernel cpuset patch provides the minimum essential kernel
mechanisms required to efficiently implement such subsets. It
1.3 How are cpusets implemented ?
---------------------------------
-Cpusets provide a Linux kernel (2.6.7 and above) mechanism to constrain
-which CPUs and Memory Nodes are used by a process or set of processes.
+Cpusets provide a Linux kernel mechanism to constrain which CPUs and
+Memory Nodes are used by a process or set of processes.
The Linux kernel already has a pair of mechanisms to specify on which
CPUs a task may be scheduled (sched_setaffinity) and on which Memory
If the cpuset flag file 'memory_migrate' is set true, then when
tasks are attached to that cpuset, any pages that task had
allocated to it on nodes in its previous cpuset are migrated
-to the tasks new cpuset. Depending on the implementation,
-this migration may either be done by swapping the page out,
-so that the next time the page is referenced, it will be paged
-into the tasks new cpuset, usually on the node where it was
-referenced, or this migration may be done by directly copying
-the pages from the tasks previous cpuset to the new cpuset,
-where possible to the same node, relative to the new cpuset,
-as the node that held the page, relative to the old cpuset.
+to the tasks new cpuset. The relative placement of the page within
+the cpuset is preserved during these migration operations if possible.
+For example if the page was on the second valid node of the prior cpuset
+then the page will be placed on the second valid node of the new cpuset.
+
Also if 'memory_migrate' is set true, then if that cpusets
'mems' file is modified, pages allocated to tasks in that
cpuset, that were on nodes in the previous setting of 'mems',
-will be moved to nodes in the new setting of 'mems.' Again,
-depending on the implementation, this might be done by swapping,
-or by direct copying. In either case, pages that were not in
-the tasks prior cpuset, or in the cpusets prior 'mems' setting,
-will not be moved.
+will be moved to nodes in the new setting of 'mems.'
+Pages that were not in the tasks prior cpuset, or in the cpusets
+prior 'mems' setting, will not be moved.
There is an exception to the above. If hotplug functionality is used
to remove all the CPUs that are currently assigned to a cpuset,
# The next line should display '/Charlie'
cat /proc/self/cpuset
-In the case that a change of cpuset includes wanting to move already
-allocated memory pages, consider further the work of IWAMOTO
-Toshihiro <iwamoto@valinux.co.jp> for page remapping and memory
-hotremoval, which can be found at:
-
- http://people.valinux.co.jp/~iwamoto/mh.html
-
-The integration of cpusets with such memory migration is not yet
-available.
-
In the future, a C library interface to cpusets will likely be
available. For now, the only way to query or modify cpusets is
via the cpuset file system, using the various cd, mkdir, echo, cat,
Page migration allows a process to manually relocate the node on which its
pages are located through the MF_MOVE and MF_MOVE_ALL options while setting
-a new memory policy. The pages of process can also be relocated
+a new memory policy via mbind(). The pages of process can also be relocated
from another process using the sys_migrate_pages() function call. The
migrate_pages function call takes two sets of nodes and moves pages of a
process that are located on the from nodes to the destination nodes.
-
-Manual migration is very useful if for example the scheduler has relocated
+Page migration functions are provided by the numactl package by Andi Kleen
+(a version later than 0.9.3 is required. Get it from
+ftp://ftp.suse.com/pub/people/ak). numactl provided libnuma which
+provides an interface similar to other numa functionality for page migration.
+cat /proc/<pid>/numa_maps allows an easy review of where the pages of
+a process are located. See also the numa_maps manpage in the numactl package.
+
+Manual migration is useful if for example the scheduler has relocated
a process to a processor on a distant node. A batch scheduler or an
administrator may detect the situation and move the pages of the process
nearer to the new processor. At some point in the future we may have
Larger installations usually partition the system using cpusets into
sections of nodes. Paul Jackson has equipped cpusets with the ability to
-move pages when a task is moved to another cpuset. This allows automatic
-control over locality of a process. If a task is moved to a new cpuset
-then also all its pages are moved with it so that the performance of the
-process does not sink dramatically (as is the case today).
+move pages when a task is moved to another cpuset (See ../cpusets.txt).
+Cpusets allows the automation of process locality. If a task is moved to
+a new cpuset then also all its pages are moved with it so that the
+performance of the process does not sink dramatically. Also the pages
+of processes in a cpuset are moved if the allowed memory nodes of a
+cpuset are changed.
Page migration allows the preservation of the relative location of pages
within a group of nodes for all migration techniques which will preserve a
Processes will run with similar performance after migration.
Page migration occurs in several steps. First a high level
-description for those trying to use migrate_pages() and then
-a low level description of how the low level details work.
+description for those trying to use migrate_pages() from the kernel
+(for userspace usage see the Andi Kleen's numactl package mentioned above)
+and then a low level description of how the low level details work.
-A. Use of migrate_pages()
--------------------------
+A. In kernel use of migrate_pages()
+-----------------------------------
1. Remove pages from the LRU.
Lists of pages to be migrated are generated by scanning over
pages and moving them into lists. This is done by
- calling isolate_lru_page() or __isolate_lru_page().
+ calling isolate_lru_page().
Calling isolate_lru_page increases the references to the page
- so that it cannot vanish under us.
+ so that it cannot vanish while the page migration occurs.
+ It also prevents the swapper or other scans to encounter
+ the page.
-2. Generate a list of newly allocates page to move the contents
- of the first list to.
+2. Generate a list of newly allocates page. These pages will contain the
+ contents of the pages from the first list after page migration is
+ complete.
3. The migrate_pages() function is called which attempts
to do the migration. It returns the moved pages in the
4. The leftover pages of various types are returned
to the LRU using putback_to_lru_pages() or otherwise
disposed of. The pages will still have the refcount as
- increased by isolate_lru_pages()!
+ increased by isolate_lru_pages() if putback_to_lru_pages() is not
+ used! The kernel may want to handle the various cases of failures in
+ different ways.
-B. Operation of migrate_pages()
---------------------------------
+B. How migrate_pages() works
+----------------------------
-migrate_pages does several passes over its list of pages. A page is moved
-if all references to a page are removable at the time.
+migrate_pages() does several passes over its list of pages. A page is moved
+if all references to a page are removable at the time. The page has
+already been removed from the LRU via isolate_lru_page() and the refcount
+is increased so that the page cannot be freed while page migration occurs.
Steps:
3. Make sure that the page has assigned swap cache entry if
it is an anonyous page. The swap cache reference is necessary
- to preserve the information contain in the page table maps.
+ to preserve the information contain in the page table maps while
+ page migration occurs.
4. Prep the new page that we want to move to. It is locked
and set to not being uptodate so that all accesses to the new
- page immediately lock while we are moving references.
+ page immediately lock while the move is in progress.
-5. All the page table references to the page are either dropped (file backed)
- or converted to swap references (anonymous pages). This should decrease the
- reference count.
+5. All the page table references to the page are either dropped (file
+ backed pages) or converted to swap references (anonymous pages).
+ This should decrease the reference count.
-6. The radix tree lock is taken
+6. The radix tree lock is taken. This will cause all processes trying
+ to reestablish a pte to block on the radix tree spinlock.
7. The refcount of the page is examined and we back out if references remain
otherwise we know that we are the only one referencing this page.
8. The radix tree is checked and if it does not contain the pointer to this
- page then we back out.
+ page then we back out because someone else modified the mapping first.
9. The mapping is checked. If the mapping is gone then a truncate action may
be in progress and we back out.
-10. The new page is prepped with some settings from the old page so that accesses
- to the new page will be discovered to have the correct settings.
+10. The new page is prepped with some settings from the old page so that
+ accesses to the new page will be discovered to have the correct settings.
11. The radix tree is changed to point to the new page.
-12. The reference count of the old page is dropped because the reference has now
- been removed.
+12. The reference count of the old page is dropped because the radix tree
+ reference is gone.
-13. The radix tree lock is dropped.
+13. The radix tree lock is dropped. With that lookups become possible again
+ and other processes will move from spinning on the tree lock to sleeping on
+ the locked new page.
14. The page contents are copied to the new page.
17. Queued up writeback on the new page is triggered.
-18. If swap pte's were generated for the page then remove them again.
+18. If swap pte's were generated for the page then replace them with real
+ ptes. This will reenable access for processes not blocked by the page lock.
+
+19. The page locks are dropped from the old and new page.
+ Processes waiting on the page lock can continue.
+
+20. The new page is moved to the LRU and can be scanned by the swapper
+ etc again.
+
+TODO list
+---------
+
+- Page migration requires the use of swap handles to preserve the
+ information of the anonymous page table entries. This means that swap
+ space is reserved but never used. The maximum number of swap handles used
+ is determined by CHUNK_SIZE (see mm/mempolicy.c) per ongoing migration.
+ Reservation of pages could be avoided by having a special type of swap
+ handle that does not require swap space and that would only track the page
+ references. Something like that was proposed by Marcelo Tosatti in the
+ past (search for migration cache on lkml or linux-mm@kvack.org).
-19. The locks are dropped from the old and new page.
+- Page migration unmaps ptes for file backed pages and requires page
+ faults to reestablish these ptes. This could be optimized by somehow
+ recording the references before migration and then reestablish them later.
+ However, there are several locking challenges that have to be overcome
+ before this is possible.
-20. The new page is moved to the LRU.
+- Page migration generates read ptes for anonymous pages. Dirty page
+ faults are required to make the pages writable again. It may be possible
+ to generate a pte marked dirty if it is known that the page is dirty and
+ that this process has the only reference to that page.
-Christoph Lameter, December 19, 2005.
+Christoph Lameter, March 8, 2006.
source "drivers/spi/Kconfig"
+source "drivers/w1/Kconfig"
+
source "drivers/hwmon/Kconfig"
#source "drivers/l3/Kconfig"
}
#endif
+
+#define LCM_ALC_EN 0x8000
+
+void frontlight_set(struct locomo *lchip, int duty, int vr, int bpwf)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&lchip->lock, flags);
+ locomo_writel(bpwf, lchip->base + LOCOMO_FRONTLIGHT + LOCOMO_ALS);
+ udelay(100);
+ locomo_writel(duty, lchip->base + LOCOMO_FRONTLIGHT + LOCOMO_ALD);
+ locomo_writel(bpwf | LCM_ALC_EN, lchip->base + LOCOMO_FRONTLIGHT + LOCOMO_ALS);
+ spin_unlock_irqrestore(&lchip->lock, flags);
+}
+
+
/**
* locomo_probe - probe for a single LoCoMo chip.
* @phys_addr: physical address of device.
/* FrontLight */
locomo_writel(0, lchip->base + LOCOMO_FRONTLIGHT + LOCOMO_ALS);
locomo_writel(0, lchip->base + LOCOMO_FRONTLIGHT + LOCOMO_ALD);
+
+ /* Same constants can be used for collie and poodle
+ (depending on CONFIG options in original sharp code)? */
+ frontlight_set(lchip, 163, 0, 148);
+
/* Longtime timer */
locomo_writel(0, lchip->base + LOCOMO_LTINT);
/* SPI */
DEFINE(TI_TP_VALUE, offsetof(struct thread_info, tp_value));
DEFINE(TI_FPSTATE, offsetof(struct thread_info, fpstate));
DEFINE(TI_VFPSTATE, offsetof(struct thread_info, vfpstate));
- DEFINE(TI_IWMMXT_STATE, (offsetof(struct thread_info, fpstate)+4)&~7);
+#ifdef CONFIG_IWMMXT
+ DEFINE(TI_IWMMXT_STATE, offsetof(struct thread_info, fpstate.iwmmxt));
+#endif
BLANK();
DEFINE(S_R0, offsetof(struct pt_regs, ARM_r0));
DEFINE(S_R1, offsetof(struct pt_regs, ARM_r1));
#include <asm/mach/arch.h>
+#include "compat.h"
+
/*
* Usage:
* - do not go blindly adding fields, add them at the end
--- /dev/null
+/*
+ * linux/arch/arm/kernel/compat.h
+ *
+ * Copyright (C) 2001 Russell King
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+extern void convert_to_tag_list(struct tag *tags);
+
+extern void squash_mem_tags(struct tag *tag);
#include <linux/kallsyms.h>
#include <linux/init.h>
#include <linux/cpu.h>
+#include <linux/elfcore.h>
#include <asm/leds.h>
#include <asm/processor.h>
* This is our default idle handler. We need to disable
* interrupts here to ensure we don't miss a wakeup call.
*/
-void default_idle(void)
+static void default_idle(void)
{
if (hlt_counter)
cpu_relax();
static int ptrace_getwmmxregs(struct task_struct *tsk, void __user *ufp)
{
struct thread_info *thread = task_thread_info(tsk);
- void *ptr = &thread->fpstate;
if (!test_ti_thread_flag(thread, TIF_USING_IWMMXT))
return -ENODATA;
iwmmxt_task_disable(thread); /* force it to ram */
- /* The iWMMXt state is stored doubleword-aligned. */
- if (((long) ptr) & 4)
- ptr += 4;
- return copy_to_user(ufp, ptr, 0x98) ? -EFAULT : 0;
+ return copy_to_user(ufp, &thread->fpstate.iwmmxt, IWMMXT_SIZE)
+ ? -EFAULT : 0;
}
/*
static int ptrace_setwmmxregs(struct task_struct *tsk, void __user *ufp)
{
struct thread_info *thread = task_thread_info(tsk);
- void *ptr = &thread->fpstate;
if (!test_ti_thread_flag(thread, TIF_USING_IWMMXT))
return -EACCES;
iwmmxt_task_release(thread); /* force a reload */
- /* The iWMMXt state is stored doubleword-aligned. */
- if (((long) ptr) & 4)
- ptr += 4;
- return copy_from_user(ptr, ufp, 0x98) ? -EFAULT : 0;
+ return copy_from_user(&thread->fpstate.iwmmxt, ufp, IWMMXT_SIZE)
+ ? -EFAULT : 0;
}
#endif
#include <asm/mach/irq.h>
#include <asm/mach/time.h>
+#include "compat.h"
+
#ifndef MEM_SIZE
#define MEM_SIZE (16*1024*1024)
#endif
__setup("fpe=", fpe_setup);
#endif
-extern unsigned int mem_fclk_21285;
extern void paging_init(struct meminfo *, struct machine_desc *desc);
-extern void convert_to_tag_list(struct tag *tags);
-extern void squash_mem_tags(struct tag *tag);
extern void reboot_setup(char *str);
extern int root_mountflags;
extern void _stext, _text, _etext, __data_start, _edata, _end;
mul xh, yl, xh
mla xh, xl, yh, xh
- mov ip, xl, asr #16
- mov yh, yl, asr #16
+ mov ip, xl, lsr #16
+ mov yh, yl, lsr #16
bic xl, xl, ip, lsl #16
bic yl, yl, yh, lsl #16
mla xh, yh, ip, xh
comment "IXP4xx Platforms"
-# This entry is placed on top because otherwise it would have
-# been shown as a submenu.
config MACH_NSLU2
bool
- prompt "NSLU2" if !(MACH_IXDP465 || MACH_IXDPG425 || ARCH_IXDP425 || ARCH_ADI_COYOTE || ARCH_AVILA || ARCH_IXCDP1100 || ARCH_PRPMC1100 || MACH_GTWX5715)
+ prompt "Linksys NSLU2"
help
Say 'Y' here if you want your kernel to support Linksys's
NSLU2 NAS device. For more information on this platform,
{
ixp4xx_sys_init();
+ /* gpio 14 and 15 are _not_ clocks */
+ *IXP4XX_GPIO_GPCLKR = 0;
+
nas100d_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
nas100d_flash_resource.end =
IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1;
};
+static u64 s3c_device_spi0_dmamask = 0xffffffffUL;
+
struct platform_device s3c_device_spi0 = {
.name = "s3c2410-spi",
.id = 0,
.num_resources = ARRAY_SIZE(s3c_spi0_resource),
.resource = s3c_spi0_resource,
+ .dev = {
+ .dma_mask = &s3c_device_spi0_dmamask,
+ .coherent_dma_mask = 0xffffffffUL
+ }
};
EXPORT_SYMBOL(s3c_device_spi0);
};
+static u64 s3c_device_spi1_dmamask = 0xffffffffUL;
+
struct platform_device s3c_device_spi1 = {
.name = "s3c2410-spi",
.id = 1,
.num_resources = ARRAY_SIZE(s3c_spi1_resource),
.resource = s3c_spi1_resource,
+ .dev = {
+ .dma_mask = &s3c_device_spi1_dmamask,
+ .coherent_dma_mask = 0xffffffffUL
+ }
};
EXPORT_SYMBOL(s3c_device_spi1);
#ifdef HARVARD_CACHE
bic r0, r0, #CACHE_LINE_SIZE - 1
1: mcr p15, 0, r0, c7, c10, 1 @ clean D line
- mcr p15, 0, r0, c7, c5, 1 @ invalidate I line
add r0, r0, #CACHE_LINE_SIZE
cmp r0, r1
blo 1b
#endif
- mcr p15, 0, r0, c7, c5, 6 @ invalidate BTB
-#ifdef HARVARD_CACHE
mov r0, #0
+#ifdef HARVARD_CACHE
mcr p15, 0, r0, c7, c10, 4 @ drain write buffer
+ mcr p15, 0, r0, c7, c5, 0 @ I+BTB cache invalidate
+#else
+ mcr p15, 0, r0, c7, c5, 6 @ invalidate BTB
#endif
mov pc, lr
static void flush_pfn_alias(unsigned long pfn, unsigned long vaddr)
{
unsigned long to = ALIAS_FLUSH_START + (CACHE_COLOUR(vaddr) << PAGE_SHIFT);
+ const int zero = 0;
set_pte(TOP_PTE(to), pfn_pte(pfn, PAGE_KERNEL));
flush_tlb_kernel_page(to);
asm( "mcrr p15, 0, %1, %0, c14\n"
- " mcrr p15, 0, %1, %0, c5\n"
+ " mcr p15, 0, %2, c7, c10, 4\n"
+ " mcr p15, 0, %2, c7, c5, 0\n"
:
- : "r" (to), "r" (to + PAGE_SIZE - L1_CACHE_BYTES)
+ : "r" (to), "r" (to + PAGE_SIZE - L1_CACHE_BYTES), "r" (zero)
: "cc");
}
*/
void lapic_shutdown(void)
{
+ unsigned long flags;
+
if (!cpu_has_apic)
return;
- local_irq_disable();
+ local_irq_save(flags);
clear_local_APIC();
if (enabled_via_apicbase)
disable_local_APIC();
- local_irq_enable();
+ local_irq_restore(flags);
}
#ifdef CONFIG_PM
strongly in flux, so no good recommendation can be made.
config CRASH_DUMP
- bool "kernel crash dumps (EXPERIMENTAL)"
+ bool "Build a kdump crash kernel (EXPERIMENTAL)"
depends on PPC_MULTIPLATFORM && PPC64 && EXPERIMENTAL
help
Build a kernel suitable for use as a kdump capture kernel.
bdnz 2b
/* Do a cache flush for our text, in case OF didn't */
-3: lis r9,_start@h
+3: lis r9,_start@ha
+ addi r9,r9,_start@l
add r9,r0,r9
lis r8,_etext@ha
addi r8,r8,_etext@l
4: dcbf r0,r9
icbi r0,r9
addi r9,r9,0x20
- cmplwi 0,r9,8
+ cmplw cr0,r9,r8
blt 4b
sync
isync
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.15-rc5
-# Tue Dec 20 15:59:26 2005
+# Linux kernel version: 2.6.16-rc6
+# Wed Mar 15 16:19:48 2006
#
CONFIG_PPC64=y
CONFIG_64BIT=y
CONFIG_SYSVIPC_COMPAT=y
CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+CONFIG_PPC_OF=y
+CONFIG_PPC_UDBG_16550=y
+# CONFIG_GENERIC_TBSYNC is not set
+# CONFIG_DEFAULT_UIMAGE is not set
#
# Processor support
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
-CONFIG_CLEAN_COMPILE=y
CONFIG_LOCK_KERNEL=y
CONFIG_INIT_ENV_ARG_LIMIT=32
# CONFIG_BSD_PROCESS_ACCT is not set
CONFIG_SYSCTL=y
# CONFIG_AUDIT is not set
-CONFIG_HOTPLUG=y
-CONFIG_KOBJECT_UEVENT=y
# CONFIG_IKCONFIG is not set
# CONFIG_CPUSETS is not set
CONFIG_INITRAMFS_SOURCE=""
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_ALL is not set
# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
+CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_CC_ALIGN_LABELS=0
CONFIG_CC_ALIGN_LOOPS=0
CONFIG_CC_ALIGN_JUMPS=0
+CONFIG_SLAB=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
+# CONFIG_SLOB is not set
#
# Loadable module support
# CONFIG_PPC_PMAC is not set
# CONFIG_PPC_MAPLE is not set
CONFIG_PPC_CELL=y
-CONFIG_PPC_OF=y
# CONFIG_U3_DART is not set
CONFIG_PPC_RTAS=y
# CONFIG_RTAS_ERROR_LOGGING is not set
CONFIG_MMIO_NVRAM=y
CONFIG_CELL_IIC=y
# CONFIG_PPC_MPC106 is not set
-# CONFIG_GENERIC_TBSYNC is not set
# CONFIG_CPU_FREQ is not set
# CONFIG_WANT_EARLY_SERIAL is not set
+#
+# Cell Broadband Engine options
+#
+CONFIG_SPU_FS=y
+
#
# Kernel options
#
CONFIG_FORCE_MAX_ZONEORDER=13
# CONFIG_IOMMU_VMERGE is not set
CONFIG_KEXEC=y
+# CONFIG_CRASH_DUMP is not set
CONFIG_IRQ_ALL_CPUS=y
# CONFIG_NUMA is not set
CONFIG_ARCH_SELECT_MEMORY_MODEL=y
#
# Networking options
#
+# CONFIG_NETDEBUG is not set
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
CONFIG_UNIX=y
# Core Netfilter Configuration
#
# CONFIG_NETFILTER_NETLINK is not set
+CONFIG_NETFILTER_XTABLES=m
+CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
+CONFIG_NETFILTER_XT_TARGET_MARK=m
+CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
+CONFIG_NETFILTER_XT_TARGET_NOTRACK=m
+CONFIG_NETFILTER_XT_MATCH_COMMENT=m
+CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
+# CONFIG_NETFILTER_XT_MATCH_DCCP is not set
+CONFIG_NETFILTER_XT_MATCH_HELPER=m
+CONFIG_NETFILTER_XT_MATCH_LENGTH=m
+CONFIG_NETFILTER_XT_MATCH_LIMIT=m
+CONFIG_NETFILTER_XT_MATCH_MAC=m
+CONFIG_NETFILTER_XT_MATCH_MARK=m
+CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
+CONFIG_NETFILTER_XT_MATCH_REALM=m
+CONFIG_NETFILTER_XT_MATCH_SCTP=m
+CONFIG_NETFILTER_XT_MATCH_STATE=m
+CONFIG_NETFILTER_XT_MATCH_STRING=m
+CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
#
# IP: Netfilter Configuration
# CONFIG_IP_NF_PPTP is not set
CONFIG_IP_NF_QUEUE=m
CONFIG_IP_NF_IPTABLES=m
-CONFIG_IP_NF_MATCH_LIMIT=m
CONFIG_IP_NF_MATCH_IPRANGE=m
-CONFIG_IP_NF_MATCH_MAC=m
-CONFIG_IP_NF_MATCH_PKTTYPE=m
-CONFIG_IP_NF_MATCH_MARK=m
CONFIG_IP_NF_MATCH_MULTIPORT=m
CONFIG_IP_NF_MATCH_TOS=m
CONFIG_IP_NF_MATCH_RECENT=m
CONFIG_IP_NF_MATCH_ECN=m
CONFIG_IP_NF_MATCH_DSCP=m
CONFIG_IP_NF_MATCH_AH_ESP=m
-CONFIG_IP_NF_MATCH_LENGTH=m
CONFIG_IP_NF_MATCH_TTL=m
-CONFIG_IP_NF_MATCH_TCPMSS=m
-CONFIG_IP_NF_MATCH_HELPER=m
-CONFIG_IP_NF_MATCH_STATE=m
-CONFIG_IP_NF_MATCH_CONNTRACK=m
CONFIG_IP_NF_MATCH_OWNER=m
CONFIG_IP_NF_MATCH_ADDRTYPE=m
-CONFIG_IP_NF_MATCH_REALM=m
-CONFIG_IP_NF_MATCH_SCTP=m
-# CONFIG_IP_NF_MATCH_DCCP is not set
-CONFIG_IP_NF_MATCH_COMMENT=m
CONFIG_IP_NF_MATCH_HASHLIMIT=m
-CONFIG_IP_NF_MATCH_STRING=m
+CONFIG_IP_NF_MATCH_POLICY=m
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_ULOG=m
CONFIG_IP_NF_TARGET_TCPMSS=m
-CONFIG_IP_NF_TARGET_NFQUEUE=m
CONFIG_IP_NF_NAT=m
CONFIG_IP_NF_NAT_NEEDED=y
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_TARGET_TOS=m
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_TARGET_DSCP=m
-CONFIG_IP_NF_TARGET_MARK=m
-CONFIG_IP_NF_TARGET_CLASSIFY=m
CONFIG_IP_NF_TARGET_TTL=m
CONFIG_IP_NF_RAW=m
-CONFIG_IP_NF_TARGET_NOTRACK=m
CONFIG_IP_NF_ARPTABLES=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m
#
# CONFIG_IP6_NF_QUEUE is not set
# CONFIG_IP6_NF_IPTABLES is not set
-# CONFIG_IP6_NF_TARGET_NFQUEUE is not set
#
# DCCP Configuration (EXPERIMENTAL)
# SCTP Configuration (EXPERIMENTAL)
#
# CONFIG_IP_SCTP is not set
+
+#
+# TIPC Configuration (EXPERIMENTAL)
+#
+# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_R8169 is not set
# CONFIG_SIS190 is not set
CONFIG_SKGE=m
+# CONFIG_SKY2 is not set
# CONFIG_SK98LIN is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
+CONFIG_SPIDER_NET=y
# CONFIG_MV643XX_ETH is not set
#
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_SERIAL_NONSTANDARD=y
+# CONFIG_COMPUTONE is not set
# CONFIG_ROCKETPORT is not set
# CONFIG_CYCLADES is not set
# CONFIG_DIGIEPCA is not set
+# CONFIG_MOXA_INTELLIO is not set
# CONFIG_MOXA_SMARTIO is not set
# CONFIG_ISI is not set
# CONFIG_SYNCLINK is not set
# CONFIG_SYNCLINKMP is not set
+# CONFIG_SYNCLINK_GT is not set
# CONFIG_N_HDLC is not set
# CONFIG_SPECIALIX is not set
# CONFIG_SX is not set
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_8250_NR_UARTS=4
+CONFIG_SERIAL_8250_RUNTIME_UARTS=4
# CONFIG_SERIAL_8250_EXTENDED is not set
#
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set
+#
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+
#
# Dallas's 1-wire bus
#
# CONFIG_INFINIBAND is not set
#
-# SN Devices
+# EDAC - error detection and reporting (RAS) (EXPERIMENTAL)
#
#
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
# CONFIG_XFS_FS is not set
+# CONFIG_OCFS2_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_INOTIFY=y
CONFIG_HUGETLB_PAGE=y
CONFIG_RAMFS=y
# CONFIG_RELAYFS_FS is not set
+# CONFIG_CONFIGFS_FS is not set
#
# Miscellaneous filesystems
# CONFIG_SGI_PARTITION is not set
# CONFIG_ULTRIX_PARTITION is not set
# CONFIG_SUN_PARTITION is not set
+# CONFIG_KARMA_PARTITION is not set
CONFIG_EFI_PARTITION=y
#
# Kernel hacking
#
# CONFIG_PRINTK_TIME is not set
-CONFIG_DEBUG_KERNEL=y
CONFIG_MAGIC_SYSRQ=y
+CONFIG_DEBUG_KERNEL=y
CONFIG_LOG_BUF_SHIFT=15
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_SCHEDSTATS is not set
# CONFIG_DEBUG_SLAB is not set
+# CONFIG_DEBUG_MUTEXES is not set
# CONFIG_DEBUG_SPINLOCK is not set
CONFIG_DEBUG_SPINLOCK_SLEEP=y
# CONFIG_DEBUG_KOBJECT is not set
# CONFIG_DEBUG_INFO is not set
CONFIG_DEBUG_FS=y
# CONFIG_DEBUG_VM is not set
+# CONFIG_FORCED_INLINING is not set
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_DEBUG_STACKOVERFLOW is not set
# CONFIG_DEBUG_STACK_USAGE is not set
# CONFIG_XMON is not set
CONFIG_IRQSTACKS=y
# CONFIG_BOOTX_TEXT is not set
+# CONFIG_PPC_EARLY_DEBUG_LPAR is not set
+# CONFIG_PPC_EARLY_DEBUG_G5 is not set
+# CONFIG_PPC_EARLY_DEBUG_RTAS is not set
+# CONFIG_PPC_EARLY_DEBUG_MAPLE is not set
+# CONFIG_PPC_EARLY_DEBUG_ISERIES is not set
#
# Security options
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.15-rc5
-# Tue Dec 20 15:59:32 2005
+# Linux kernel version: 2.6.16-rc6
+# Wed Mar 15 16:19:52 2006
#
CONFIG_PPC64=y
CONFIG_64BIT=y
CONFIG_SYSVIPC_COMPAT=y
CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+CONFIG_PPC_OF=y
+# CONFIG_PPC_UDBG_16550 is not set
+# CONFIG_GENERIC_TBSYNC is not set
+# CONFIG_DEFAULT_UIMAGE is not set
#
# Processor support
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
-CONFIG_CLEAN_COMPILE=y
CONFIG_LOCK_KERNEL=y
CONFIG_INIT_ENV_ARG_LIMIT=32
CONFIG_SYSCTL=y
CONFIG_AUDIT=y
CONFIG_AUDITSYSCALL=y
-CONFIG_HOTPLUG=y
-CONFIG_KOBJECT_UEVENT=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
# CONFIG_CPUSETS is not set
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_ALL is not set
# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
+CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_CC_ALIGN_LABELS=0
CONFIG_CC_ALIGN_LOOPS=0
CONFIG_CC_ALIGN_JUMPS=0
+CONFIG_SLAB=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
+# CONFIG_SLOB is not set
#
# Loadable module support
# CONFIG_MMIO_NVRAM is not set
CONFIG_IBMVIO=y
# CONFIG_PPC_MPC106 is not set
-# CONFIG_GENERIC_TBSYNC is not set
# CONFIG_CPU_FREQ is not set
# CONFIG_WANT_EARLY_SERIAL is not set
#
# Networking options
#
+# CONFIG_NETDEBUG is not set
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
CONFIG_UNIX=y
# Core Netfilter Configuration
#
# CONFIG_NETFILTER_NETLINK is not set
+CONFIG_NETFILTER_XTABLES=m
+CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
+CONFIG_NETFILTER_XT_TARGET_CONNMARK=m
+CONFIG_NETFILTER_XT_TARGET_MARK=m
+CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
+CONFIG_NETFILTER_XT_TARGET_NOTRACK=m
+CONFIG_NETFILTER_XT_MATCH_COMMENT=m
+CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m
+CONFIG_NETFILTER_XT_MATCH_CONNMARK=m
+CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
+# CONFIG_NETFILTER_XT_MATCH_DCCP is not set
+CONFIG_NETFILTER_XT_MATCH_HELPER=m
+CONFIG_NETFILTER_XT_MATCH_LENGTH=m
+CONFIG_NETFILTER_XT_MATCH_LIMIT=m
+CONFIG_NETFILTER_XT_MATCH_MAC=m
+CONFIG_NETFILTER_XT_MATCH_MARK=m
+CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
+CONFIG_NETFILTER_XT_MATCH_REALM=m
+CONFIG_NETFILTER_XT_MATCH_SCTP=m
+CONFIG_NETFILTER_XT_MATCH_STATE=m
+CONFIG_NETFILTER_XT_MATCH_STRING=m
+CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
#
# IP: Netfilter Configuration
# CONFIG_IP_NF_PPTP is not set
CONFIG_IP_NF_QUEUE=m
CONFIG_IP_NF_IPTABLES=m
-CONFIG_IP_NF_MATCH_LIMIT=m
CONFIG_IP_NF_MATCH_IPRANGE=m
-CONFIG_IP_NF_MATCH_MAC=m
-CONFIG_IP_NF_MATCH_PKTTYPE=m
-CONFIG_IP_NF_MATCH_MARK=m
CONFIG_IP_NF_MATCH_MULTIPORT=m
CONFIG_IP_NF_MATCH_TOS=m
CONFIG_IP_NF_MATCH_RECENT=m
CONFIG_IP_NF_MATCH_ECN=m
CONFIG_IP_NF_MATCH_DSCP=m
CONFIG_IP_NF_MATCH_AH_ESP=m
-CONFIG_IP_NF_MATCH_LENGTH=m
CONFIG_IP_NF_MATCH_TTL=m
-CONFIG_IP_NF_MATCH_TCPMSS=m
-CONFIG_IP_NF_MATCH_HELPER=m
-CONFIG_IP_NF_MATCH_STATE=m
-CONFIG_IP_NF_MATCH_CONNTRACK=m
CONFIG_IP_NF_MATCH_OWNER=m
CONFIG_IP_NF_MATCH_ADDRTYPE=m
-CONFIG_IP_NF_MATCH_REALM=m
-CONFIG_IP_NF_MATCH_SCTP=m
-# CONFIG_IP_NF_MATCH_DCCP is not set
-CONFIG_IP_NF_MATCH_COMMENT=m
-CONFIG_IP_NF_MATCH_CONNMARK=m
-CONFIG_IP_NF_MATCH_CONNBYTES=m
CONFIG_IP_NF_MATCH_HASHLIMIT=m
-CONFIG_IP_NF_MATCH_STRING=m
+CONFIG_IP_NF_MATCH_POLICY=m
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_ULOG=m
CONFIG_IP_NF_TARGET_TCPMSS=m
-CONFIG_IP_NF_TARGET_NFQUEUE=m
CONFIG_IP_NF_NAT=m
CONFIG_IP_NF_NAT_NEEDED=y
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_TARGET_TOS=m
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_TARGET_DSCP=m
-CONFIG_IP_NF_TARGET_MARK=m
-CONFIG_IP_NF_TARGET_CLASSIFY=m
CONFIG_IP_NF_TARGET_TTL=m
-CONFIG_IP_NF_TARGET_CONNMARK=m
CONFIG_IP_NF_TARGET_CLUSTERIP=m
CONFIG_IP_NF_RAW=m
-CONFIG_IP_NF_TARGET_NOTRACK=m
CONFIG_IP_NF_ARPTABLES=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m
# SCTP Configuration (EXPERIMENTAL)
#
# CONFIG_IP_SCTP is not set
+
+#
+# TIPC Configuration (EXPERIMENTAL)
+#
+# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_SCSI_IPR is not set
# CONFIG_SCSI_QLOGIC_FC is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
-CONFIG_SCSI_QLA2XXX=y
-# CONFIG_SCSI_QLA21XX is not set
-# CONFIG_SCSI_QLA22XX is not set
-# CONFIG_SCSI_QLA2300 is not set
-# CONFIG_SCSI_QLA2322 is not set
-# CONFIG_SCSI_QLA6312 is not set
-# CONFIG_SCSI_QLA24XX is not set
+# CONFIG_SCSI_QLA_FC is not set
# CONFIG_SCSI_LPFC is not set
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_R8169 is not set
# CONFIG_SIS190 is not set
# CONFIG_SKGE is not set
+# CONFIG_SKY2 is not set
# CONFIG_SK98LIN is not set
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
#
# CONFIG_I2C is not set
+#
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+
#
# Dallas's 1-wire bus
#
# CONFIG_INFINIBAND is not set
#
-# SN Devices
+# EDAC - error detection and reporting (RAS) (EXPERIMENTAL)
#
#
CONFIG_XFS_SECURITY=y
CONFIG_XFS_POSIX_ACL=y
# CONFIG_XFS_RT is not set
+# CONFIG_OCFS2_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_INOTIFY=y
# CONFIG_HUGETLB_PAGE is not set
CONFIG_RAMFS=y
# CONFIG_RELAYFS_FS is not set
+# CONFIG_CONFIGFS_FS is not set
#
# Miscellaneous filesystems
#
# Instrumentation Support
#
-CONFIG_PROFILING=y
-CONFIG_OPROFILE=y
# CONFIG_KPROBES is not set
#
# Kernel hacking
#
# CONFIG_PRINTK_TIME is not set
-CONFIG_DEBUG_KERNEL=y
CONFIG_MAGIC_SYSRQ=y
+CONFIG_DEBUG_KERNEL=y
CONFIG_LOG_BUF_SHIFT=17
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_SCHEDSTATS is not set
# CONFIG_DEBUG_SLAB is not set
+# CONFIG_DEBUG_MUTEXES is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_KOBJECT is not set
# CONFIG_DEBUG_INFO is not set
CONFIG_DEBUG_FS=y
# CONFIG_DEBUG_VM is not set
+# CONFIG_FORCED_INLINING is not set
# CONFIG_RCU_TORTURE_TEST is not set
CONFIG_DEBUG_STACKOVERFLOW=y
CONFIG_DEBUG_STACK_USAGE=y
# CONFIG_DEBUGGER is not set
CONFIG_IRQSTACKS=y
+# CONFIG_PPC_EARLY_DEBUG_LPAR is not set
+# CONFIG_PPC_EARLY_DEBUG_G5 is not set
+# CONFIG_PPC_EARLY_DEBUG_RTAS is not set
+# CONFIG_PPC_EARLY_DEBUG_MAPLE is not set
+# CONFIG_PPC_EARLY_DEBUG_ISERIES is not set
#
# Security options
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.15-rc5
-# Tue Dec 20 15:59:36 2005
+# Linux kernel version: 2.6.16-rc6
+# Wed Mar 15 16:19:54 2006
#
CONFIG_PPC64=y
CONFIG_64BIT=y
CONFIG_SYSVIPC_COMPAT=y
CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+CONFIG_PPC_OF=y
+CONFIG_PPC_UDBG_16550=y
+CONFIG_GENERIC_TBSYNC=y
+# CONFIG_DEFAULT_UIMAGE is not set
#
# Processor support
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
-CONFIG_CLEAN_COMPILE=y
CONFIG_LOCK_KERNEL=y
CONFIG_INIT_ENV_ARG_LIMIT=32
# CONFIG_BSD_PROCESS_ACCT is not set
CONFIG_SYSCTL=y
# CONFIG_AUDIT is not set
-# CONFIG_HOTPLUG is not set
-CONFIG_KOBJECT_UEVENT=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
# CONFIG_CPUSETS is not set
CONFIG_KALLSYMS=y
CONFIG_KALLSYMS_ALL=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
+CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_CC_ALIGN_LABELS=0
CONFIG_CC_ALIGN_LOOPS=0
CONFIG_CC_ALIGN_JUMPS=0
+CONFIG_SLAB=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
+# CONFIG_SLOB is not set
#
# Loadable module support
# CONFIG_PPC_PMAC is not set
CONFIG_PPC_MAPLE=y
# CONFIG_PPC_CELL is not set
-CONFIG_PPC_OF=y
CONFIG_U3_DART=y
CONFIG_MPIC=y
# CONFIG_PPC_RTAS is not set
# CONFIG_MMIO_NVRAM is not set
CONFIG_MPIC_BROKEN_U3=y
# CONFIG_PPC_MPC106 is not set
-CONFIG_GENERIC_TBSYNC=y
# CONFIG_CPU_FREQ is not set
# CONFIG_WANT_EARLY_SERIAL is not set
CONFIG_FORCE_MAX_ZONEORDER=13
CONFIG_IOMMU_VMERGE=y
CONFIG_KEXEC=y
+# CONFIG_CRASH_DUMP is not set
CONFIG_IRQ_ALL_CPUS=y
# CONFIG_NUMA is not set
CONFIG_ARCH_SELECT_MEMORY_MODEL=y
#
# Networking options
#
+# CONFIG_NETDEBUG is not set
CONFIG_PACKET=y
CONFIG_PACKET_MMAP=y
CONFIG_UNIX=y
# SCTP Configuration (EXPERIMENTAL)
#
# CONFIG_IP_SCTP is not set
+
+#
+# TIPC Configuration (EXPERIMENTAL)
+#
+# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_R8169 is not set
# CONFIG_SIS190 is not set
# CONFIG_SKGE is not set
+# CONFIG_SKY2 is not set
# CONFIG_SK98LIN is not set
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_8250_NR_UARTS=4
+CONFIG_SERIAL_8250_RUNTIME_UARTS=4
# CONFIG_SERIAL_8250_EXTENDED is not set
#
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set
+#
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+
#
# Dallas's 1-wire bus
#
# may also be needed; see USB_STORAGE Help for more information
#
# CONFIG_USB_STORAGE is not set
+# CONFIG_USB_LIBUSUAL is not set
#
# USB Input Devices
#
CONFIG_USB_HID=y
CONFIG_USB_HIDINPUT=y
+# CONFIG_USB_HIDINPUT_POWERBOOK is not set
# CONFIG_HID_FF is not set
# CONFIG_USB_HIDDEV is not set
# CONFIG_USB_AIPTEK is not set
# CONFIG_USB_YEALINK is not set
# CONFIG_USB_XPAD is not set
# CONFIG_USB_ATI_REMOTE is not set
+# CONFIG_USB_ATI_REMOTE2 is not set
# CONFIG_USB_KEYSPAN_REMOTE is not set
# CONFIG_USB_APPLETOUCH is not set
# CONFIG_USB_SERIAL_AIRPRIME is not set
# CONFIG_USB_SERIAL_ANYDATA is not set
# CONFIG_USB_SERIAL_BELKIN is not set
+# CONFIG_USB_SERIAL_WHITEHEAT is not set
# CONFIG_USB_SERIAL_DIGI_ACCELEPORT is not set
# CONFIG_USB_SERIAL_CP2101 is not set
CONFIG_USB_SERIAL_CYPRESS_M8=m
# CONFIG_INFINIBAND is not set
#
-# SN Devices
+# EDAC - error detection and reporting (RAS) (EXPERIMENTAL)
#
#
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
# CONFIG_XFS_FS is not set
+# CONFIG_OCFS2_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
CONFIG_INOTIFY=y
CONFIG_HUGETLB_PAGE=y
CONFIG_RAMFS=y
# CONFIG_RELAYFS_FS is not set
+# CONFIG_CONFIGFS_FS is not set
#
# Miscellaneous filesystems
# CONFIG_SGI_PARTITION is not set
# CONFIG_ULTRIX_PARTITION is not set
# CONFIG_SUN_PARTITION is not set
+# CONFIG_KARMA_PARTITION is not set
# CONFIG_EFI_PARTITION is not set
#
# Kernel hacking
#
# CONFIG_PRINTK_TIME is not set
-CONFIG_DEBUG_KERNEL=y
CONFIG_MAGIC_SYSRQ=y
+CONFIG_DEBUG_KERNEL=y
CONFIG_LOG_BUF_SHIFT=17
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_SCHEDSTATS is not set
CONFIG_DEBUG_SLAB=y
+# CONFIG_DEBUG_MUTEXES is not set
# CONFIG_DEBUG_SPINLOCK is not set
CONFIG_DEBUG_SPINLOCK_SLEEP=y
# CONFIG_DEBUG_KOBJECT is not set
# CONFIG_DEBUG_INFO is not set
CONFIG_DEBUG_FS=y
# CONFIG_DEBUG_VM is not set
+# CONFIG_FORCED_INLINING is not set
# CONFIG_RCU_TORTURE_TEST is not set
CONFIG_DEBUG_STACKOVERFLOW=y
CONFIG_DEBUG_STACK_USAGE=y
CONFIG_XMON_DEFAULT=y
# CONFIG_IRQSTACKS is not set
CONFIG_BOOTX_TEXT=y
+# CONFIG_PPC_EARLY_DEBUG_LPAR is not set
+# CONFIG_PPC_EARLY_DEBUG_G5 is not set
+# CONFIG_PPC_EARLY_DEBUG_RTAS is not set
+# CONFIG_PPC_EARLY_DEBUG_MAPLE is not set
+# CONFIG_PPC_EARLY_DEBUG_ISERIES is not set
#
# Security options
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.15-g461d4edf-dirty
-# Fri Jan 13 11:01:47 2006
+# Linux kernel version: 2.6.16-rc6
+# Wed Mar 15 16:19:56 2006
#
# CONFIG_PPC64 is not set
CONFIG_PPC32=y
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
-CONFIG_CLEAN_COMPILE=y
CONFIG_BROKEN_ON_SMP=y
CONFIG_INIT_ENV_ARG_LIMIT=32
#
# Networking options
#
+# CONFIG_NETDEBUG is not set
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
CONFIG_UNIX=y
# SCTP Configuration (EXPERIMENTAL)
#
# CONFIG_IP_SCTP is not set
+
+#
+# TIPC Configuration (EXPERIMENTAL)
+#
+# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_VLAN_8021Q is not set
#
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
+# CONFIG_SERIAL_JSM is not set
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set
+#
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+
#
# Dallas's 1-wire bus
#
# CONFIG_SENSORS_ASB100 is not set
# CONFIG_SENSORS_ATXP1 is not set
# CONFIG_SENSORS_DS1621 is not set
+# CONFIG_SENSORS_F71805F is not set
# CONFIG_SENSORS_FSCHER is not set
# CONFIG_SENSORS_FSCPOS is not set
# CONFIG_SENSORS_GL518SM is not set
# CONFIG_INFINIBAND is not set
#
-# SN Devices
+# EDAC - error detection and reporting (RAS) (EXPERIMENTAL)
#
#
# CONFIG_SGI_PARTITION is not set
# CONFIG_ULTRIX_PARTITION is not set
# CONFIG_SUN_PARTITION is not set
+# CONFIG_KARMA_PARTITION is not set
# CONFIG_EFI_PARTITION is not set
#
#
# Hardware crypto devices
#
-
-#
-# SEC2.x Options
-#
-CONFIG_MPC8349E_SEC2x=y
-
-#
-# SEC2.x Test Options
-#
-CONFIG_MPC8349E_SEC2xTEST=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.15
-# Sat Jan 14 16:26:08 2006
+# Linux kernel version: 2.6.16-rc6
+# Wed Mar 15 16:21:32 2006
#
# CONFIG_PPC64 is not set
CONFIG_PPC32=y
CONFIG_ARCH_MAY_HAVE_PC_FDC=y
CONFIG_PPC_OF=y
# CONFIG_PPC_UDBG_16550 is not set
-# CONFIG_CRASH_DUMP is not set
# CONFIG_GENERIC_TBSYNC is not set
+# CONFIG_DEFAULT_UIMAGE is not set
#
# Processor support
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
-CONFIG_CLEAN_COMPILE=y
CONFIG_BROKEN_ON_SMP=y
CONFIG_INIT_ENV_ARG_LIMIT=32
#
# Networking options
#
+# CONFIG_NETDEBUG is not set
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
CONFIG_UNIX=y
# Core Netfilter Configuration
#
# CONFIG_NETFILTER_NETLINK is not set
+CONFIG_NETFILTER_XTABLES=m
+CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
+CONFIG_NETFILTER_XT_TARGET_MARK=m
+CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
+CONFIG_NETFILTER_XT_TARGET_NOTRACK=m
+CONFIG_NETFILTER_XT_MATCH_COMMENT=m
+CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
+# CONFIG_NETFILTER_XT_MATCH_DCCP is not set
+CONFIG_NETFILTER_XT_MATCH_HELPER=m
+CONFIG_NETFILTER_XT_MATCH_LENGTH=m
+CONFIG_NETFILTER_XT_MATCH_LIMIT=m
+CONFIG_NETFILTER_XT_MATCH_MAC=m
+CONFIG_NETFILTER_XT_MATCH_MARK=m
+CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
+CONFIG_NETFILTER_XT_MATCH_REALM=m
+CONFIG_NETFILTER_XT_MATCH_SCTP=m
+CONFIG_NETFILTER_XT_MATCH_STATE=m
+CONFIG_NETFILTER_XT_MATCH_STRING=m
+CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
#
# IP: Netfilter Configuration
CONFIG_IP_NF_PPTP=m
# CONFIG_IP_NF_QUEUE is not set
CONFIG_IP_NF_IPTABLES=m
-CONFIG_IP_NF_MATCH_LIMIT=m
CONFIG_IP_NF_MATCH_IPRANGE=m
-CONFIG_IP_NF_MATCH_MAC=m
-CONFIG_IP_NF_MATCH_PKTTYPE=m
-CONFIG_IP_NF_MATCH_MARK=m
CONFIG_IP_NF_MATCH_MULTIPORT=m
CONFIG_IP_NF_MATCH_TOS=m
CONFIG_IP_NF_MATCH_RECENT=m
CONFIG_IP_NF_MATCH_ECN=m
CONFIG_IP_NF_MATCH_DSCP=m
CONFIG_IP_NF_MATCH_AH_ESP=m
-CONFIG_IP_NF_MATCH_LENGTH=m
CONFIG_IP_NF_MATCH_TTL=m
-CONFIG_IP_NF_MATCH_TCPMSS=m
-CONFIG_IP_NF_MATCH_HELPER=m
-CONFIG_IP_NF_MATCH_STATE=m
-CONFIG_IP_NF_MATCH_CONNTRACK=m
CONFIG_IP_NF_MATCH_OWNER=m
-# CONFIG_IP_NF_MATCH_ADDRTYPE is not set
-# CONFIG_IP_NF_MATCH_REALM is not set
-# CONFIG_IP_NF_MATCH_SCTP is not set
-CONFIG_IP_NF_MATCH_DCCP=m
-# CONFIG_IP_NF_MATCH_COMMENT is not set
-# CONFIG_IP_NF_MATCH_HASHLIMIT is not set
-CONFIG_IP_NF_MATCH_STRING=m
+CONFIG_IP_NF_MATCH_ADDRTYPE=m
+CONFIG_IP_NF_MATCH_HASHLIMIT=m
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
-# CONFIG_IP_NF_TARGET_LOG is not set
+CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_ULOG=m
CONFIG_IP_NF_TARGET_TCPMSS=m
-# CONFIG_IP_NF_TARGET_NFQUEUE is not set
CONFIG_IP_NF_NAT=m
CONFIG_IP_NF_NAT_NEEDED=y
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_NAT_TFTP=m
CONFIG_IP_NF_NAT_AMANDA=m
CONFIG_IP_NF_NAT_PPTP=m
-# CONFIG_IP_NF_MANGLE is not set
+CONFIG_IP_NF_MANGLE=m
+CONFIG_IP_NF_TARGET_TOS=m
+CONFIG_IP_NF_TARGET_ECN=m
+CONFIG_IP_NF_TARGET_DSCP=m
+CONFIG_IP_NF_TARGET_TTL=m
CONFIG_IP_NF_RAW=m
-CONFIG_IP_NF_TARGET_NOTRACK=m
CONFIG_IP_NF_ARPTABLES=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m
# SCTP Configuration (EXPERIMENTAL)
#
# CONFIG_IP_SCTP is not set
+
+#
+# TIPC Configuration (EXPERIMENTAL)
+#
+# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_VLAN_8021Q is not set
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set
+CONFIG_NET_CLS_ROUTE=y
#
# Network testing
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
CONFIG_BLK_DEV_PDC202XX_NEW=y
-# CONFIG_PDC202XX_FORCE is not set
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIIMAGE is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_SCSI_IPR is not set
# CONFIG_SCSI_QLOGIC_FC is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
-CONFIG_SCSI_QLA2XXX=y
-# CONFIG_SCSI_QLA2XXX_EMBEDDED_FIRMWARE is not set
+# CONFIG_SCSI_QLA_FC is not set
# CONFIG_SCSI_LPFC is not set
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
#
CONFIG_SERIAL_CORE=m
CONFIG_SERIAL_PMACZILOG=m
+# CONFIG_SERIAL_JSM is not set
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set
+#
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+
#
# Dallas's 1-wire bus
#
#
CONFIG_USB_HID=y
CONFIG_USB_HIDINPUT=y
+CONFIG_USB_HIDINPUT_POWERBOOK=y
# CONFIG_HID_FF is not set
# CONFIG_USB_HIDDEV is not set
# CONFIG_USB_AIPTEK is not set
# CONFIG_INFINIBAND is not set
#
-# SN Devices
+# EDAC - error detection and reporting (RAS) (EXPERIMENTAL)
#
#
# CONFIG_SGI_PARTITION is not set
# CONFIG_ULTRIX_PARTITION is not set
# CONFIG_SUN_PARTITION is not set
+# CONFIG_KARMA_PARTITION is not set
# CONFIG_EFI_PARTITION is not set
#
# CONFIG_DEBUG_INFO is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_DEBUG_VM is not set
+# CONFIG_FORCED_INLINING is not set
# CONFIG_RCU_TORTURE_TEST is not set
CONFIG_DEBUGGER=y
CONFIG_XMON=y
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_BLK_DEV_GENERIC=y
# CONFIG_BLK_DEV_OPTI621 is not set
-# CONFIG_BLK_DEV_SL82C105 is not set
+CONFIG_BLK_DEV_SL82C105=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
#endif /* CONFIG_PPC_MULTIPLATFORM */
if (mode == PCI_PROBE_NORMAL)
hose->last_busno = bus->subordinate = pci_scan_child_bus(bus);
- pci_bus_add_devices(bus);
}
static int __init pcibios_init(void)
printk("PCI: Probing PCI hardware\n");
/* Scan all of the recorded PCI controllers. */
- list_for_each_entry_safe(hose, tmp, &hose_list, list_node)
+ list_for_each_entry_safe(hose, tmp, &hose_list, list_node) {
scan_phb(hose);
+ pci_bus_add_devices(hose->bus);
+ }
#ifndef CONFIG_PPC_ISERIES
if (pci_probe_only)
EXPORT_SYMBOL(_outsw_ns);
EXPORT_SYMBOL(_insl_ns);
EXPORT_SYMBOL(_outsl_ns);
-EXPORT_SYMBOL(ioremap);
-#ifdef CONFIG_44x
-EXPORT_SYMBOL(ioremap64);
-#endif
-EXPORT_SYMBOL(__ioremap);
-EXPORT_SYMBOL(iounmap);
-#ifdef CONFIG_PPC32
-EXPORT_SYMBOL(ioremap_bot); /* aka VMALLOC_END */
-#endif
#if defined(CONFIG_PPC32) && (defined(CONFIG_BLK_DEV_IDE) || defined(CONFIG_BLK_DEV_IDE_MODULE))
EXPORT_SYMBOL(ppc_ide_md);
EXPORT_SYMBOL(flush_dcache_range);
#ifdef CONFIG_SMP
-EXPORT_SYMBOL(smp_call_function);
#ifdef CONFIG_PPC32
EXPORT_SYMBOL(smp_hw_index);
#endif
error = rtas_call(rtas_token("get-time-of-day"), 0, 8, ret);
if (error == RTAS_CLOCK_BUSY || rtas_is_extended_busy(error)) {
if (in_interrupt() && printk_ratelimit()) {
- memset(&rtc_tm, 0, sizeof(struct rtc_time));
+ memset(rtc_tm, 0, sizeof(struct rtc_time));
printk(KERN_WARNING "error: reading clock"
" would delay interrupt\n");
return; /* delay not allowed */
return 0;
}
-static int __devinit setup_phb(struct device_node *dev,
- struct pci_controller *phb)
+int __devinit setup_phb(struct device_node *dev, struct pci_controller *phb)
{
if (is_python(dev))
python_countermeasures(dev);
return 0;
}
-struct pci_controller * __devinit init_phb_dynamic(struct device_node *dn)
-{
- struct pci_controller *phb;
- int primary;
-
- primary = list_empty(&hose_list);
- phb = pcibios_alloc_controller(dn);
- if (!phb)
- return NULL;
- setup_phb(dn, phb);
- pci_process_bridge_OF_ranges(phb, dn, primary);
-
- pci_setup_phb_io_dynamic(phb, primary);
-
- pci_devs_phb_init_dynamic(phb);
- scan_phb(phb);
-
- return phb;
-}
-EXPORT_SYMBOL(init_phb_dynamic);
-
/* RPA-specific bits for removing PHBs */
int pcibios_remove_root_bus(struct pci_controller *phb)
{
* the two values of tb_update_count match and are even then the
* tb_to_xs and stamp_xsec values are consistent. If not, then it
* loops back and reads them again until this criteria is met.
+ * We expect the caller to have done the first increment of
+ * vdso_data->tb_update_count already.
*/
- ++(vdso_data->tb_update_count);
- smp_wmb();
vdso_data->tb_orig_stamp = new_tb_stamp;
vdso_data->stamp_xsec = new_stamp_xsec;
vdso_data->tb_to_xs = new_tb_to_xs;
unsigned long offset;
u64 new_stamp_xsec;
u64 tlen, t2x;
+ u64 tb, xsec_old, xsec_new;
+ struct gettimeofday_vars *varp;
if (__USE_RTC())
return;
tlen = current_tick_length();
offset = cur_tb - do_gtod.varp->tb_orig_stamp;
- if (tlen == last_tick_len && offset < 0x80000000u) {
- /* check that we're still in sync; if not, resync */
- struct timeval tv;
- __do_gettimeofday(&tv, cur_tb);
- if (tv.tv_sec <= xtime.tv_sec &&
- (tv.tv_sec < xtime.tv_sec ||
- tv.tv_usec * 1000 <= xtime.tv_nsec))
- return;
- }
+ if (tlen == last_tick_len && offset < 0x80000000u)
+ return;
if (tlen != last_tick_len) {
t2x = mulhdu(tlen << TICKLEN_SHIFT, ticklen_to_xs);
last_tick_len = tlen;
new_stamp_xsec = (u64) xtime.tv_nsec * XSEC_PER_SEC;
do_div(new_stamp_xsec, 1000000000);
new_stamp_xsec += (u64) xtime.tv_sec * XSEC_PER_SEC;
+
+ ++vdso_data->tb_update_count;
+ smp_mb();
+
+ /*
+ * Make sure time doesn't go backwards for userspace gettimeofday.
+ */
+ tb = get_tb();
+ varp = do_gtod.varp;
+ xsec_old = mulhdu(tb - varp->tb_orig_stamp, varp->tb_to_xs)
+ + varp->stamp_xsec;
+ xsec_new = mulhdu(tb - cur_tb, t2x) + new_stamp_xsec;
+ if (xsec_new < xsec_old)
+ new_stamp_xsec += xsec_old - xsec_new;
+
update_gtod(cur_tb, new_stamp_xsec, t2x);
}
}
#endif
+ /* Make userspace gettimeofday spin until we're done. */
+ ++vdso_data->tb_update_count;
+ smp_mb();
+
/*
* Subtract off the number of nanoseconds since the
* beginning of the last tick.
* It is computed as:
* ticklen_to_xs = 2^N / (tb_ticks_per_jiffy * 1e9)
* where N = 64 + 20 - TICKLEN_SCALE - TICKLEN_SHIFT
- * so as to give the result as a 0.64 fixed-point fraction.
+ * which turns out to be N = 51 - SHIFT_HZ.
+ * This gives the result as a 0.64 fixed-point fraction.
+ * That value is reduced by an offset amounting to 1 xsec per
+ * 2^31 timebase ticks to avoid problems with time going backwards
+ * by 1 xsec when we do timer_recalc_offset due to losing the
+ * fractional xsec. That offset is equal to ppc_tb_freq/2^51
+ * since there are 2^20 xsec in a second.
*/
- div128_by_32(1ULL << (64 + 20 - TICKLEN_SCALE - TICKLEN_SHIFT), 0,
- tb_ticks_per_jiffy, &res);
+ div128_by_32((1ULL << 51) - ppc_tb_freq, 0,
+ tb_ticks_per_jiffy << SHIFT_HZ, &res);
div128_by_32(res.result_high, res.result_low, NSEC_PER_SEC, &res);
ticklen_to_xs = res.result_low;
unsigned long ioremap_base;
unsigned long ioremap_bot;
+EXPORT_SYMBOL(ioremap_bot); /* aka VMALLOC_END */
int io_bat_index;
#if defined(CONFIG_6xx) || defined(CONFIG_POWER3)
{
return __ioremap(addr, size, _PAGE_NO_CACHE);
}
+EXPORT_SYMBOL(ioremap64);
void __iomem *
ioremap(phys_addr_t addr, unsigned long size)
return ioremap64(addr64, size);
}
#endif /* CONFIG_PHYS_64BIT */
+EXPORT_SYMBOL(ioremap);
void __iomem *
__ioremap(phys_addr_t addr, unsigned long size, unsigned long flags)
out:
return (void __iomem *) (v + ((unsigned long)addr & ~PAGE_MASK));
}
+EXPORT_SYMBOL(__ioremap);
void iounmap(volatile void __iomem *addr)
{
if (addr > high_memory && (unsigned long) addr < ioremap_bot)
vunmap((void *) (PAGE_MASK & (unsigned long)addr));
}
+EXPORT_SYMBOL(iounmap);
void __iomem *ioport_map(unsigned long port, unsigned int len)
{
pmac_mb.model_id = PMAC_TYPE_COMET;
iounmap(mach_id_ptr);
}
-#endif /* CONFIG_POWER4 */
-#ifdef CONFIG_6xx
/* Set default value of powersave_nap on machines that support it.
* It appears that uninorth rev 3 has a problem with it, we don't
* enable it on those. In theory, the flush-on-lock property is
* NAP mode
*/
powersave_lowspeed = 1;
-#endif /* CONFIG_6xx */
-#ifdef CONFIG_POWER4
+
+#else /* CONFIG_POWER4 */
powersave_nap = 1;
-#endif
+#endif /* CONFIG_POWER4 */
+
/* Check for "mobile" machine */
if (model && (strncmp(model, "PowerBook", 9) == 0
|| strncmp(model, "iBook", 5) == 0))
/* Probe motherboard chipset */
pmac_feature_init();
- /* We can NAP */
- powersave_nap = 1;
- printk(KERN_INFO "Using native/NAP idle loop\n");
-
/* Initialize debug stuff */
udbg_scc_init(!!strstr(cmd_line, "sccdbg"));
udbg_adb_init(!!strstr(cmd_line, "btextdbg"));
depends on RTAS_PROC && PPC_PSERIES
config LPARCFG
- tristate "LPAR Configuration Data"
+ bool "LPAR Configuration Data"
depends on PPC_PSERIES || PPC_ISERIES
help
Provide system capacity information via human readable
#include <linux/pci.h>
#include <asm/pci-bridge.h>
+#include <asm/ppc-pci.h>
static struct pci_bus *
find_bus_among_children(struct pci_bus *bus,
}
}
EXPORT_SYMBOL_GPL(pcibios_add_pci_devices);
+
+struct pci_controller * __devinit init_phb_dynamic(struct device_node *dn)
+{
+ struct pci_controller *phb;
+ int primary;
+
+ primary = list_empty(&hose_list);
+ phb = pcibios_alloc_controller(dn);
+ if (!phb)
+ return NULL;
+ setup_phb(dn, phb);
+ pci_process_bridge_OF_ranges(phb, dn, 0);
+
+ pci_setup_phb_io_dynamic(phb, primary);
+
+ pci_devs_phb_init_dynamic(phb);
+
+ if (dn->child)
+ eeh_add_device_tree_early(dn);
+
+ scan_phb(phb);
+ pcibios_fixup_new_pci_devices(phb->bus, 0);
+ pci_bus_add_devices(phb->bus);
+
+ return phb;
+}
+EXPORT_SYMBOL_GPL(init_phb_dynamic);
#define EDAC_MC_VERSION "edac_mc Ver: 2.0.0 " __DATE__
+/* For now, disable the EDAC sysfs code. The sysfs interface that EDAC
+ * presents to user space needs more thought, and is likely to change
+ * substantially.
+ */
+#define DISABLE_EDAC_SYSFS
+
#ifdef CONFIG_EDAC_DEBUG
/* Values of 0 to 4 will generate output */
int edac_debug_level = 1;
/* EDAC Controls, setable by module parameter, and sysfs */
static int log_ue = 1;
static int log_ce = 1;
-static int panic_on_ue = 1;
+static int panic_on_ue;
static int poll_msec = 1000;
static int check_pci_parity = 0; /* default YES check PCI parity */
/* START sysfs data and methods */
+#ifndef DISABLE_EDAC_SYSFS
+
static const char *mem_types[] = {
[MEM_EMPTY] = "Empty",
[MEM_RESERVED] = "Reserved",
.default_attrs = (struct attribute **) memctrl_attr,
};
+#endif /* DISABLE_EDAC_SYSFS */
/* Initialize the main sysfs entries for edac:
* /sys/devices/system/edac
* !0 FAILURE
*/
static int edac_sysfs_memctrl_setup(void)
+#ifdef DISABLE_EDAC_SYSFS
+{
+ return 0;
+}
+#else
{
int err=0;
return err;
}
+#endif /* DISABLE_EDAC_SYSFS */
/*
* MC teardown:
*/
static void edac_sysfs_memctrl_teardown(void)
{
+#ifndef DISABLE_EDAC_SYSFS
debugf0("MC: " __FILE__ ": %s()\n", __func__);
/* Unregister the MC's kobject */
/* Unregister the 'edac' object */
sysdev_class_unregister(&edac_class);
+#endif /* DISABLE_EDAC_SYSFS */
}
+#ifndef DISABLE_EDAC_SYSFS
+
/*
* /sys/devices/system/edac/pci;
* data structures and methods
.default_attrs = (struct attribute **) edac_pci_attr,
};
+#endif /* DISABLE_EDAC_SYSFS */
+
/**
* edac_sysfs_pci_setup()
*
*/
static int edac_sysfs_pci_setup(void)
+#ifdef DISABLE_EDAC_SYSFS
+{
+ return 0;
+}
+#else
{
int err;
}
return err;
}
-
+#endif /* DISABLE_EDAC_SYSFS */
static void edac_sysfs_pci_teardown(void)
{
+#ifndef DISABLE_EDAC_SYSFS
debugf0("MC: " __FILE__ ": %s()\n", __func__);
kobject_unregister(&edac_pci_kobj);
kobject_put(&edac_pci_kobj);
+#endif
}
+#ifndef DISABLE_EDAC_SYSFS
+
/* EDAC sysfs CSROW data structures and methods */
/* Set of more detailed csrow<id> attribute show/store functions */
.default_attrs = (struct attribute **) mci_attr,
};
+#endif /* DISABLE_EDAC_SYSFS */
+
#define EDAC_DEVICE_SYMLINK "device"
/*
* !0 Failure
*/
static int edac_create_sysfs_mci_device(struct mem_ctl_info *mci)
+#ifdef DISABLE_EDAC_SYSFS
+{
+ return 0;
+}
+#else
{
int i;
int err;
return err;
}
+#endif /* DISABLE_EDAC_SYSFS */
/*
* remove a Memory Controller instance
*/
static void edac_remove_sysfs_mci_device(struct mem_ctl_info *mci)
{
+#ifndef DISABLE_EDAC_SYSFS
int i;
debugf0("MC: " __FILE__ ": %s()\n", __func__);
kobject_unregister(&mci->edac_mci_kobj);
kobject_put(&mci->edac_mci_kobj);
+#endif /* DISABLE_EDAC_SYSFS */
}
/* END OF sysfs data and methods */
p += sprintf(p, "PMU driver version : %d\n", PMU_DRIVER_VERSION);
p += sprintf(p, "PMU firmware version : %02x\n", pmu_version);
p += sprintf(p, "AC Power : %d\n",
- ((pmu_power_flags & PMU_PWR_AC_PRESENT) != 0));
+ ((pmu_power_flags & PMU_PWR_AC_PRESENT) != 0) || pmu_battery_count == 0);
p += sprintf(p, "Battery count : %d\n", pmu_battery_count);
return p - page;
/*
mxb - v4l2 driver for the Multimedia eXtension Board
- Copyright (C) 1998-2003 Michael Hunold <michael@mihu.de>
+ Copyright (C) 1998-2006 Michael Hunold <michael@mihu.de>
Visit http://www.mihu.de/linux/saa7146/mxb/
for further details about this card.
struct video_decoder_init init;
struct i2c_msg msg;
struct tuner_setup tun_setup;
+ v4l2_std_id std = V4L2_STD_PAL_BG;
int i = 0, err = 0;
struct tea6415c_multiplex vm;
mxb->tuner->driver->command(mxb->tuner, VIDIOC_S_FREQUENCY,
&mxb->cur_freq);
+ /* set a default video standard */
+ mxb->tuner->driver->command(mxb->tuner, VIDIOC_S_STD, &std);
+
/* mute audio on tea6420s */
mxb->tea6420_1->driver->command(mxb->tea6420_1,TEA6420_SWITCH, &TEA6420_line[6][0]);
mxb->tea6420_2->driver->command(mxb->tea6420_2,TEA6420_SWITCH, &TEA6420_line[6][1]);
int one = 1;
if(V4L2_STD_PAL_I == std->id ) {
+ v4l2_std_id std = V4L2_STD_PAL_I;
DEB_D(("VIDIOC_S_STD: setting mxb for PAL_I.\n"));
/* set the 7146 gpio register -- I don't know what this does exactly */
saa7146_write(dev, GPIO_CTRL, 0x00404050);
/* unset the 7111 gpio register -- I don't know what this does exactly */
mxb->saa7111a->driver->command(mxb->saa7111a,DECODER_SET_GPIO, &zero);
+ mxb->tuner->driver->command(mxb->tuner, VIDIOC_S_STD, &std);
} else {
+ v4l2_std_id std = V4L2_STD_PAL_BG;
DEB_D(("VIDIOC_S_STD: setting mxb for PAL/NTSC/SECAM.\n"));
/* set the 7146 gpio register -- I don't know what this does exactly */
saa7146_write(dev, GPIO_CTRL, 0x00404050);
/* set the 7111 gpio register -- I don't know what this does exactly */
mxb->saa7111a->driver->command(mxb->saa7111a,DECODER_SET_GPIO, &one);
+ mxb->tuner->driver->command(mxb->tuner, VIDIOC_S_STD, &std);
}
return 0;
}
* we're at a block boundary and need to erase the whole block.
*/
pageaddr = instr->addr / priv->page_size;
- do_block = (pageaddr & 0x7) == 0 && instr->len <= blocksize;
+ do_block = (pageaddr & 0x7) == 0 && instr->len >= blocksize;
pageaddr = pageaddr << priv->page_offset;
command[0] = do_block ? OP_ERASE_BLOCK : OP_ERASE_PAGE;
if (test_and_clear_bit(nd->if_port,
&sge->stopped_tx_queues) &&
netif_running(nd)) {
- sge->stats.cmdQ_restarted[3]++;
+ sge->stats.cmdQ_restarted[2]++;
netif_wake_queue(nd);
}
}
if (unlikely(credits < count)) {
netif_stop_queue(dev);
set_bit(dev->if_port, &sge->stopped_tx_queues);
- sge->stats.cmdQ_full[3]++;
+ sge->stats.cmdQ_full[2]++;
spin_unlock(&q->lock);
if (!netif_queue_stopped(dev))
CH_ERR("%s: Tx ring full while queue awake!\n",
return NETDEV_TX_BUSY;
}
if (unlikely(credits - count < q->stop_thres)) {
- sge->stats.cmdQ_full[3]++;
+ sge->stats.cmdQ_full[2]++;
netif_stop_queue(dev);
set_bit(dev->if_port, &sge->stopped_tx_queues);
}
msleep(10);
+ pci_dma_sync_single_for_cpu(nic->pdev, nic->rx_to_clean->dma_addr,
+ RFD_BUF_LEN, PCI_DMA_FROMDEVICE);
+
if(memcmp(nic->rx_to_clean->skb->data + sizeof(struct rfd),
skb->data, ETH_DATA_LEN))
err = -EAGAIN;
err_loopback_none:
mdio_write(nic->netdev, nic->mii.phy_id, MII_BMCR, 0);
nic->loopback = lb_none;
- e100_hw_init(nic);
e100_clean_cbs(nic);
+ e100_hw_reset(nic);
err_clean_rx:
e100_rx_clean_list(nic);
return err;
e1000_rx_checksum(adapter,
(uint32_t)(status) |
((uint32_t)(rx_desc->errors) << 24),
- rx_desc->csum, skb);
+ le16_to_cpu(rx_desc->csum), skb);
skb->protocol = eth_type_trans(skb, netdev);
#ifdef CONFIG_E1000_NAPI
copydone:
e1000_rx_checksum(adapter, staterr,
- rx_desc->wb.lower.hi_dword.csum_ip.csum, skb);
+ le16_to_cpu(rx_desc->wb.lower.hi_dword.csum_ip.csum), skb);
skb->protocol = eth_type_trans(skb, netdev);
if (likely(rx_desc->wb.upper.header_status &
- E1000_RXDPS_HDRSTAT_HDRSP))
+ cpu_to_le16(E1000_RXDPS_HDRSTAT_HDRSP)))
adapter->rx_hdr_split++;
#ifdef CONFIG_E1000_NAPI
if (unlikely(adapter->vlgrp && (staterr & E1000_RXD_STAT_VP))) {
netdev->last_rx = jiffies;
next_desc:
- rx_desc->wb.middle.status_error &= ~0xFF;
+ rx_desc->wb.middle.status_error &= cpu_to_le32(~0xFF);
buffer_info->skb = NULL;
/* return some buffers to hardware, one at a time is too slow */
strcat(str, "66MHz");
else if (clock_ctrl == 6)
strcat(str, "100MHz");
- else if (clock_ctrl == 7)
- strcat(str, "133MHz");
} else {
strcpy(str, "PCI:");
if (tp->tg3_flags & TG3_FLAG_PCI_HIGH_SPEED)
if (align)
skb_reserve(skb, align);
- if (memcpy_fromiovec(skb_put(skb, len), iv, len))
+ if (memcpy_fromiovec(skb_put(skb, len), iv, len)) {
+ tun->stats.rx_dropped++;
+ kfree_skb(skb);
return -EFAULT;
+ }
skb->dev = tun->dev;
switch (tun->flags & TUN_TYPE_MASK) {
/* -ENXIO: no more subchannels. */
case -ENXIO:
return ret;
+ /* -EIO: this subchannel set not supported. */
+ case -EIO:
+ return ret;
default:
return 0;
}
#define ZFCP_STATUS_UNIT_TEMPORARY 0x00000002
#define ZFCP_STATUS_UNIT_SHARED 0x00000004
#define ZFCP_STATUS_UNIT_READONLY 0x00000008
+#define ZFCP_STATUS_UNIT_REGISTERED 0x00000010
/* FSF request status (this does not have a common part) */
#define ZFCP_STATUS_FSFREQ_NOT_INIT 0x00000000
&& (!atomic_test_mask(ZFCP_STATUS_UNIT_TEMPORARY,
&unit->status))
&& !unit->device
- && port->rport)
- scsi_add_device(port->adapter->scsi_host, 0,
- port->rport->scsi_target_id,
- unit->scsi_lun);
+ && port->rport) {
+ atomic_set_mask(ZFCP_STATUS_UNIT_REGISTERED,
+ &unit->status);
+ scsi_scan_target(&port->rport->dev, 0,
+ port->rport->scsi_target_id,
+ unit->scsi_lun, 0);
+ }
zfcp_unit_put(unit);
break;
case ZFCP_ERP_ACTION_REOPEN_PORT_FORCED:
eh_host_reset_handler: zfcp_scsi_eh_host_reset_handler,
/* FIXME(openfcp): Tune */
can_queue: 4096,
- this_id: 0,
+ this_id: -1,
/*
* FIXME:
* one less? can zfcp_create_sbale cope with it?
read_lock_irqsave(&zfcp_data.config_lock, flags);
unit = zfcp_unit_lookup(adapter, sdp->channel, sdp->id, sdp->lun);
- if (unit) {
+ if (unit && atomic_test_mask(ZFCP_STATUS_UNIT_REGISTERED,
+ &unit->status)) {
sdp->hostdata = unit;
unit->device = sdp;
zfcp_unit_get(unit);
struct zfcp_unit *unit = (struct zfcp_unit *) sdpnt->hostdata;
if (unit) {
+ atomic_clear_mask(ZFCP_STATUS_UNIT_REGISTERED, &unit->status);
sdpnt->hostdata = NULL;
unit->device = NULL;
zfcp_unit_put(unit);
"on port 0x%016Lx in recovery\n",
zfcp_get_busid_by_unit(unit),
unit->fcp_lun, unit->port->wwpn);
- retval = SCSI_MLQUEUE_DEVICE_BUSY;
+ zfcp_scsi_command_fail(scpnt, DID_NO_CONNECT);
goto out;
}
struct ata_queued_cmd *qc;
qc = ata_qc_from_tag(ap, ap->active_tag);
if (!ahci_host_intr(ap, qc))
- if (ata_ratelimit()) {
- struct pci_dev *pdev =
- to_pci_dev(ap->host_set->dev);
- dev_printk(KERN_WARNING, &pdev->dev,
+ if (ata_ratelimit())
+ dev_printk(KERN_WARNING, host_set->dev,
"unhandled interrupt on port %u\n",
i);
- }
VPRINTK("port %u\n", i);
} else {
VPRINTK("port %u (no irq)\n", i);
- if (ata_ratelimit()) {
- struct pci_dev *pdev =
- to_pci_dev(ap->host_set->dev);
- dev_printk(KERN_WARNING, &pdev->dev,
+ if (ata_ratelimit())
+ dev_printk(KERN_WARNING, host_set->dev,
"interrupt on disabled port %u\n", i);
- }
}
irq_ack |= (1 << i);
config PCMCIA_AHA152X
tristate "Adaptec AHA152X PCMCIA support"
depends on m && !64BIT
+ select SCSI_SPI_ATTRS
help
Say Y here if you intend to attach this type of PCMCIA SCSI host
adapter to your computer.
{"ADAPTEC", "Adaptec 5400S", NULL, BLIST_FORCELUN},
{"AFT PRO", "-IX CF", "0.0>", BLIST_FORCELUN},
{"BELKIN", "USB 2 HS-CF", "1.95", BLIST_FORCELUN | BLIST_INQUIRY_36},
+ {"BROWNIE", "1600U3P", NULL, BLIST_NOREPORTLUN},
{"CANON", "IPUBJD", NULL, BLIST_SPARSELUN},
{"CBOX3", "USB Storage-SMC", "300A", BLIST_FORCELUN | BLIST_INQUIRY_36},
{"CMD", "CRA-7280", NULL, BLIST_SPARSELUN}, /* CMD RAID Controller */
*/
#define FC_STARGET_NUM_ATTRS 3
#define FC_RPORT_NUM_ATTRS 9
-#define FC_HOST_NUM_ATTRS 16
+#define FC_HOST_NUM_ATTRS 17
struct fc_internal {
struct scsi_transport_template t;
{
struct address_space *mapping = page->mapping;
struct buffer_head *bh, *head;
+ int rc;
if (!mapping)
return -EAGAIN;
head = page_buffers(page);
- if (migrate_page_remove_references(newpage, page, 3))
- return -EAGAIN;
+ rc = migrate_page_remove_references(newpage, page, 3);
+ if (rc)
+ return rc;
bh = head;
do {
* For writes, i_mutex is not held on entry; it is never taken.
*
* DIO_LOCKING (simple locking for regular files)
- * For writes we are called under i_mutex and return with i_mutex held, even though
- * it is internally dropped.
+ * For writes we are called under i_mutex and return with i_mutex held, even
+ * though it is internally dropped.
* For reads, i_mutex is not held on entry, but it is taken and dropped before
* returning.
*
* DIO_OWN_LOCKING (filesystem provides synchronisation and handling of
* uninitialised data, allowing parallel direct readers and writers)
* For writes we are called without i_mutex, return without it, never touch it.
- * For reads, i_mutex is held on entry and will be released before returning.
+ * For reads we are called under i_mutex and return with i_mutex held, even
+ * though it may be internally dropped.
*
* Additional i_alloc_sem locking requirements described inline below.
*/
ssize_t retval = -EINVAL;
loff_t end = offset;
struct dio *dio;
- int reader_with_isem = (rw == READ && dio_lock_type == DIO_OWN_LOCKING);
+ int release_i_mutex = 0;
+ int acquire_i_mutex = 0;
if (rw & WRITE)
current->flags |= PF_SYNCWRITE;
* writers need to grab i_alloc_sem only (i_mutex is already held)
* For regular files using DIO_OWN_LOCKING,
* neither readers nor writers take any locks here
- * (i_mutex is already held and release for writers here)
*/
dio->lock_type = dio_lock_type;
if (dio_lock_type != DIO_NO_LOCKING) {
mapping = iocb->ki_filp->f_mapping;
if (dio_lock_type != DIO_OWN_LOCKING) {
mutex_lock(&inode->i_mutex);
- reader_with_isem = 1;
+ release_i_mutex = 1;
}
retval = filemap_write_and_wait_range(mapping, offset,
if (dio_lock_type == DIO_OWN_LOCKING) {
mutex_unlock(&inode->i_mutex);
- reader_with_isem = 0;
+ acquire_i_mutex = 1;
}
}
nr_segs, blkbits, get_blocks, end_io, dio);
if (rw == READ && dio_lock_type == DIO_LOCKING)
- reader_with_isem = 0;
+ release_i_mutex = 0;
out:
- if (reader_with_isem)
+ if (release_i_mutex)
mutex_unlock(&inode->i_mutex);
+ else if (acquire_i_mutex)
+ mutex_lock(&inode->i_mutex);
if (rw & WRITE)
current->flags &= ~PF_SYNCWRITE;
return retval;
unsigned long npages = dir_pages(inode);
unsigned chunk_mask = ~(ext2_chunk_size(inode)-1);
unsigned char *types = NULL;
- int need_revalidate = (filp->f_version != inode->i_version);
- int ret;
+ int need_revalidate = filp->f_version != inode->i_version;
if (pos > inode->i_size - EXT2_DIR_REC_LEN(1))
- goto success;
+ return 0;
if (EXT2_HAS_INCOMPAT_FEATURE(sb, EXT2_FEATURE_INCOMPAT_FILETYPE))
types = ext2_filetype_table;
"bad page in #%lu",
inode->i_ino);
filp->f_pos += PAGE_CACHE_SIZE - offset;
- ret = -EIO;
- goto done;
+ return -EIO;
}
kaddr = page_address(page);
- if (need_revalidate) {
- offset = ext2_validate_entry(kaddr, offset, chunk_mask);
+ if (unlikely(need_revalidate)) {
+ if (offset) {
+ offset = ext2_validate_entry(kaddr, offset, chunk_mask);
+ filp->f_pos = (n<<PAGE_CACHE_SHIFT) + offset;
+ }
+ filp->f_version = inode->i_version;
need_revalidate = 0;
}
de = (ext2_dirent *)(kaddr+offset);
if (de->rec_len == 0) {
ext2_error(sb, __FUNCTION__,
"zero-length directory entry");
- ret = -EIO;
ext2_put_page(page);
- goto done;
+ return -EIO;
}
if (de->inode) {
int over;
le32_to_cpu(de->inode), d_type);
if (over) {
ext2_put_page(page);
- goto success;
+ return 0;
}
}
filp->f_pos += le16_to_cpu(de->rec_len);
}
ext2_put_page(page);
}
-
-success:
- ret = 0;
-done:
- filp->f_version = inode->i_version;
- return ret;
+ return 0;
}
/*
lastlblkno = lblkno;
+ LOGSYNC_LOCK(log, flags);
if (mp->lsn != 0) {
/* inherit older/smaller lsn */
logdiff(diffp, mp->lsn, log);
- LOGSYNC_LOCK(log, flags);
if (difft < diffp) {
mp->lsn = lsn;
logdiff(diffp, mp->clsn, log);
if (difft > diffp)
mp->clsn = tblk->clsn;
- LOGSYNC_UNLOCK(log, flags);
} else {
mp->log = log;
mp->lsn = lsn;
/* insert bp after tblock in logsync list */
- LOGSYNC_LOCK(log, flags);
-
log->count++;
list_add(&mp->synclist, &tblk->synclist);
mp->clsn = tblk->clsn;
- LOGSYNC_UNLOCK(log, flags);
}
+ LOGSYNC_UNLOCK(log, flags);
}
/* write the last buffer. */
*/
lsn = tblk->lsn;
log = JFS_SBI(tblk->sb)->log;
+ LOGSYNC_LOCK(log, flags);
if (mp->lsn != 0) {
/* inherit older/smaller lsn */
logdiff(difft, lsn, log);
logdiff(diffp, mp->lsn, log);
- LOGSYNC_LOCK(log, flags);
if (difft < diffp) {
mp->lsn = lsn;
/* move mp after tblock in logsync list */
logdiff(diffp, mp->clsn, log);
if (difft > diffp)
mp->clsn = tblk->clsn;
- LOGSYNC_UNLOCK(log, flags);
} else {
mp->log = log;
mp->lsn = lsn;
/* insert mp after tblock in logsync list */
- LOGSYNC_LOCK(log, flags);
log->count++;
list_add(&mp->synclist, &tblk->synclist);
mp->clsn = tblk->clsn;
- LOGSYNC_UNLOCK(log, flags);
}
+ LOGSYNC_UNLOCK(log, flags);
write_metapage(mp);
return (0);
}
* reclaimed while we're stuck in the unlock call. */
fl->fl_u.nfs_fl.flags &= ~NFS_LCK_GRANTED;
+ /*
+ * Note: the server is supposed to either grant us the unlock
+ * request, or to deny it with NLM_LCK_DENIED_GRACE_PERIOD. In either
+ * case, we want to unlock.
+ */
+ do_vfs_lock(fl);
+
if (req->a_flags & RPC_TASK_ASYNC) {
status = nlmclnt_async_call(req, NLMPROC_UNLOCK,
&nlmclnt_unlock_ops);
/* Hrmf... Do the unlock early since locks_remove_posix()
* really expects us to free the lock synchronously */
- do_vfs_lock(fl);
if (status < 0) {
nlmclnt_release_lockargs(req);
kfree(req);
if (status < 0)
return status;
- do_vfs_lock(fl);
if (resp->status == NLM_LCK_GRANTED)
return 0;
new_ns = kmalloc(sizeof(struct namespace), GFP_KERNEL);
if (!new_ns)
- goto out;
+ return NULL;
atomic_set(&new_ns->count, 1);
INIT_LIST_HEAD(&new_ns->list);
if (!new_ns->root) {
up_write(&namespace_sem);
kfree(new_ns);
- goto out;
+ return NULL;
}
spin_lock(&vfsmount_lock);
list_add_tail(&new_ns->list, &new_ns->root->mnt_list);
if (altrootmnt)
mntput(altrootmnt);
-out:
return new_ns;
}
#define NFSDBG_FACILITY NFSDBG_VFS
#define MAX_DIRECTIO_SIZE (4096UL << PAGE_SHIFT)
+static void nfs_free_user_pages(struct page **pages, int npages, int do_dirty);
static kmem_cache_t *nfs_direct_cachep;
/*
page_count, (rw == READ), 0,
*pages, NULL);
up_read(¤t->mm->mmap_sem);
+ /*
+ * If we got fewer pages than expected from get_user_pages(),
+ * the user buffer runs off the end of a mapping; return EFAULT.
+ */
+ if (result >= 0 && result < page_count) {
+ nfs_free_user_pages(*pages, result, 0);
+ *pages = NULL;
+ result = -EFAULT;
+ }
}
return result;
}
if (status == 0)
status = nfs4_do_fsinfo(server, fhandle, info);
out:
- return status;
+ return nfs4_map_errors(status);
}
static int _nfs4_proc_getattr(struct nfs_server *server, struct nfs_fh *fhandle, struct nfs_fattr *fattr)
unsigned int save[FP_SOFT_SIZE]; /* undefined information */
};
+#define IWMMXT_SIZE 0x98
+
struct iwmmxt_struct {
- unsigned int save[0x98/sizeof(int) + 1];
+ unsigned int save[IWMMXT_SIZE / sizeof(unsigned int)];
};
union fp_state {
return ret;
}
+extern void disable_hlt(void);
+extern void enable_hlt(void);
+
#endif /* __ASSEMBLY__ */
#define arch_align_stack(x) (x)
struct cpu_context_save cpu_context; /* cpu context */
__u8 used_cp[16]; /* thread used copro */
unsigned long tp_value;
- union fp_state fpstate;
+ union fp_state fpstate __attribute__((aligned(8)));
union vfp_state vfpstate;
struct restart_block restart_block;
};
void pci_devs_phb_init(void);
void pci_devs_phb_init_dynamic(struct pci_controller *phb);
+int setup_phb(struct device_node *dev, struct pci_controller *phb);
void __devinit scan_phb(struct pci_controller *hose);
/* From rtas_pci.h */
*/
p->clear_child_tid = (clone_flags & CLONE_CHILD_CLEARTID) ? child_tidptr: NULL;
+ /*
+ * sigaltstack should be cleared when sharing the same VM
+ */
+ if ((clone_flags & (CLONE_VM|CLONE_VFORK)) == CLONE_VM)
+ p->sas_ss_sp = p->sas_ss_size = 0;
+
/*
* Syscall tracing should be turned off in the child regardless
* of CLONE_PTRACE.
MPOL_MF_MOVE | MPOL_MF_MOVE_ALL))
|| mode > MPOL_MAX)
return -EINVAL;
- if ((flags & MPOL_MF_MOVE_ALL) && !capable(CAP_SYS_RESOURCE))
+ if ((flags & MPOL_MF_MOVE_ALL) && !capable(CAP_SYS_NICE))
return -EPERM;
if (start & ~PAGE_MASK)
*/
if ((current->euid != task->suid) && (current->euid != task->uid) &&
(current->uid != task->suid) && (current->uid != task->uid) &&
- !capable(CAP_SYS_ADMIN)) {
+ !capable(CAP_SYS_NICE)) {
err = -EPERM;
goto out;
}
task_nodes = cpuset_mems_allowed(task);
/* Is the user allowed to access the target nodes? */
- if (!nodes_subset(new, task_nodes) && !capable(CAP_SYS_ADMIN)) {
+ if (!nodes_subset(new, task_nodes) && !capable(CAP_SYS_NICE)) {
err = -EPERM;
goto out;
}
err = do_migrate_pages(mm, &old, &new,
- capable(CAP_SYS_ADMIN) ? MPOL_MF_MOVE_ALL : MPOL_MF_MOVE);
+ capable(CAP_SYS_NICE) ? MPOL_MF_MOVE_ALL : MPOL_MF_MOVE);
out:
mmput(mm);
return err;
* the page.
*/
if (!mapping || page_mapcount(page) + nr_refs != page_count(page))
- return 1;
+ return -EAGAIN;
/*
* Establish swap ptes for anonymous pages or destroy pte
* If the page was not migrated then the PageSwapCache bit
* is still set and the operation may continue.
*/
- try_to_unmap(page, 1);
+ if (try_to_unmap(page, 1) == SWAP_FAIL)
+ /* A vma has VM_LOCKED set -> Permanent failure */
+ return -EPERM;
/*
* Give up if we were unable to remove all mappings.
*/
if (page_mapcount(page))
- return 1;
+ return -EAGAIN;
write_lock_irq(&mapping->tree_lock);
if (!page_mapping(page) || page_count(page) != nr_refs ||
*radix_pointer != page) {
write_unlock_irq(&mapping->tree_lock);
- return 1;
+ return -EAGAIN;
}
/*
*/
int migrate_page(struct page *newpage, struct page *page)
{
+ int rc;
+
BUG_ON(PageWriteback(page)); /* Writeback must be complete */
- if (migrate_page_remove_references(newpage, page, 2))
- return -EAGAIN;
+ rc = migrate_page_remove_references(newpage, page, 2);
+
+ if (rc)
+ return rc;
migrate_page_copy(newpage, page);
# watchers
obj-$(CONFIG_BRIDGE_EBT_LOG) += ebt_log.o
-obj-$(CONFIG_BRIDGE_EBT_LOG) += ebt_ulog.o
+obj-$(CONFIG_BRIDGE_EBT_ULOG) += ebt_ulog.o
a4_included = ((fc & (IEEE80211_FCTL_TODS | IEEE80211_FCTL_FROMDS)) ==
(IEEE80211_FCTL_TODS | IEEE80211_FCTL_FROMDS));
qc_included = ((WLAN_FC_GET_TYPE(fc) == IEEE80211_FTYPE_DATA) &&
- (WLAN_FC_GET_STYPE(fc) & 0x08));
+ (WLAN_FC_GET_STYPE(fc) & IEEE80211_STYPE_QOS_DATA));
aad_len = 22;
if (a4_included)
aad_len += 6;
if (is_beacon(beacon->header.frame_ctl)) {
if (ieee->handle_beacon != NULL)
- ieee->handle_beacon(dev, beacon, &network);
+ ieee->handle_beacon(dev, beacon, target);
} else {
if (ieee->handle_probe_response != NULL)
- ieee->handle_probe_response(dev, beacon, &network);
+ ieee->handle_probe_response(dev, beacon, target);
}
}
if (((length > mtu) && (sk->sk_protocol == IPPROTO_UDP)) &&
(rt->u.dst.dev->features & NETIF_F_UFO)) {
- if(ip_ufo_append_data(sk, getfrag, from, length, hh_len,
- fragheaderlen, transhdrlen, mtu, flags))
+ err = ip_ufo_append_data(sk, getfrag, from, length, hh_len,
+ fragheaderlen, transhdrlen, mtu,
+ flags);
+ if (err)
goto error;
-
return 0;
}
struct arpt_table *t;
t = xt_find_table_lock(NF_ARP, entries->name);
- if (t || !IS_ERR(t)) {
+ if (t && !IS_ERR(t)) {
struct xt_table_info *private = t->private;
duprintf("t->private->number = %u\n",
private->number);
/* Update AIMD parameters */
if (tp->snd_cwnd > hstcp_aimd_vals[ca->ai].cwnd) {
while (tp->snd_cwnd > hstcp_aimd_vals[ca->ai].cwnd &&
- ca->ai < HSTCP_AIMD_MAX)
+ ca->ai < HSTCP_AIMD_MAX - 1)
ca->ai++;
} else if (tp->snd_cwnd < hstcp_aimd_vals[ca->ai].cwnd) {
while (tp->snd_cwnd > hstcp_aimd_vals[ca->ai].cwnd &&
limit = min(send_win, cong_win);
+ /* If a full-sized TSO skb can be sent, do it. */
+ if (limit >= 65536)
+ return 0;
+
if (sysctl_tcp_tso_win_divisor) {
u32 chunk = min(tp->snd_wnd, tp->snd_cwnd * tp->mss_cache);
int addr_type;
unsigned int attrs;
int matchlen;
- unsigned int scope;
+ int scope;
unsigned int rule;
};
goto out;
memcpy(tmp_hdr, skb->nh.raw, hdr_len);
if (ipv6_clear_mutable_options(skb->nh.ipv6h, hdr_len))
- goto out;
+ goto free_out;
skb->nh.ipv6h->priority = 0;
skb->nh.ipv6h->flow_lbl[0] = 0;
skb->nh.ipv6h->flow_lbl[1] = 0;
struct inet_timewait_sock **twp)
{
struct inet_hashinfo *hinfo = death_row->hashinfo;
- const struct inet_sock *inet = inet_sk(sk);
+ struct inet_sock *inet = inet_sk(sk);
const struct ipv6_pinfo *np = inet6_sk(sk);
const struct in6_addr *daddr = &np->rcv_saddr;
const struct in6_addr *saddr = &np->daddr;
}
unique:
+ /* Must record num and sport now. Otherwise we will see
+ * in hash table socket with a funny identity. */
+ inet->num = lport;
+ inet->sport = htons(lport);
BUG_TRAP(sk_unhashed(sk));
__sk_add_node(sk, &head->chain);
sk->sk_hash = hash;
if (((length > mtu) && (sk->sk_protocol == IPPROTO_UDP)) &&
(rt->u.dst.dev->features & NETIF_F_UFO)) {
- if(ip6_ufo_append_data(sk, getfrag, from, length, hh_len,
- fragheaderlen, transhdrlen, mtu, flags))
+ err = ip6_ufo_append_data(sk, getfrag, from, length, hh_len,
+ fragheaderlen, transhdrlen, mtu,
+ flags);
+ if (err)
goto error;
-
return 0;
}
if (nfqa[NFQA_CFG_PARAMS-1]) {
struct nfqnl_msg_config_params *params;
- params = NFA_DATA(nfqa[NFQA_CFG_PARAMS-1]);
+ if (!queue) {
+ ret = -ENOENT;
+ goto out_put;
+ }
+ params = NFA_DATA(nfqa[NFQA_CFG_PARAMS-1]);
nfqnl_set_mode(queue, params->copy_mode,
ntohl(params->copy_range));
}
msg->msg_namelen = sizeof(*addr);
}
+ if (nlk->flags & NETLINK_RECV_PKTINFO)
+ netlink_cmsg_recv_pktinfo(msg, skb);
+
if (NULL == siocb->scm) {
memset(&scm, 0, sizeof(scm));
siocb->scm = &scm;
netlink_dump(sk);
scm_recv(sock, msg, siocb->scm, flags);
- if (nlk->flags & NETLINK_RECV_PKTINFO)
- netlink_cmsg_recv_pktinfo(msg, skb);
out:
netlink_rcv_wake(sk);
rtattr_failure:
nlmsg_failure:
- skb_trim(skb, b - skb->data);
+ kfree_skb(skb);
return -1;
}
err = -EINVAL;
if (!xprt)
- goto out_err;
+ goto out_no_xprt;
if (vers >= program->nrvers || !(version = program->version[vers]))
goto out_err;
kfree(clnt);
out_err:
xprt_destroy(xprt);
+out_no_xprt:
return ERR_PTR(err);
}
*/
void rpc_wake_up(struct rpc_wait_queue *queue)
{
- struct rpc_task *task;
-
+ struct rpc_task *task, *next;
struct list_head *head;
+
spin_lock_bh(&queue->lock);
head = &queue->tasks[queue->maxpriority];
for (;;) {
- while (!list_empty(head)) {
- task = list_entry(head->next, struct rpc_task, u.tk_wait.list);
+ list_for_each_entry_safe(task, next, head, u.tk_wait.list)
__rpc_wake_up_task(task);
- }
if (head == &queue->tasks[0])
break;
head--;
*/
void rpc_wake_up_status(struct rpc_wait_queue *queue, int status)
{
+ struct rpc_task *task, *next;
struct list_head *head;
- struct rpc_task *task;
spin_lock_bh(&queue->lock);
head = &queue->tasks[queue->maxpriority];
for (;;) {
- while (!list_empty(head)) {
- task = list_entry(head->next, struct rpc_task, u.tk_wait.list);
+ list_for_each_entry_safe(task, next, head, u.tk_wait.list) {
task->tk_status = status;
__rpc_wake_up_task(task);
}