N: Erik Inge Bolsø
E: knan@mo.himolde.no
D: Misc kernel hacks
+D: Updated PC speaker driver for 2.3
+S: Norway
N: Andreas E. Bombe
E: andreas.bombe@munich.netsurf.de
S: Sunnyvale, California 94088-4132
S: USA
+N: Stas Sergeev
+E: stsp@users.sourceforge.net
+D: PCM PC-Speaker driver
+D: misc fixes
+S: Russia
+
N: Simon Shapiro
E: shimon@i-Connect.Net
W: http://www.-i-Connect.Net/~shimon
--- /dev/null
+################################################################################
+# #
+# NFS/RDMA README #
+# #
+################################################################################
+
+ Author: NetApp and Open Grid Computing
+ Date: February 25, 2008
+
+Table of Contents
+~~~~~~~~~~~~~~~~~
+ - Overview
+ - Getting Help
+ - Installation
+ - Check RDMA and NFS Setup
+ - NFS/RDMA Setup
+
+Overview
+~~~~~~~~
+
+ This document describes how to install and setup the Linux NFS/RDMA client
+ and server software.
+
+ The NFS/RDMA client was first included in Linux 2.6.24. The NFS/RDMA server
+ was first included in the following release, Linux 2.6.25.
+
+ In our testing, we have obtained excellent performance results (full 10Gbit
+ wire bandwidth at minimal client CPU) under many workloads. The code passes
+ the full Connectathon test suite and operates over both Infiniband and iWARP
+ RDMA adapters.
+
+Getting Help
+~~~~~~~~~~~~
+
+ If you get stuck, you can ask questions on the
+
+ nfs-rdma-devel@lists.sourceforge.net
+
+ mailing list.
+
+Installation
+~~~~~~~~~~~~
+
+ These instructions are a step by step guide to building a machine for
+ use with NFS/RDMA.
+
+ - Install an RDMA device
+
+ Any device supported by the drivers in drivers/infiniband/hw is acceptable.
+
+ Testing has been performed using several Mellanox-based IB cards, the
+ Ammasso AMS1100 iWARP adapter, and the Chelsio cxgb3 iWARP adapter.
+
+ - Install a Linux distribution and tools
+
+ The first kernel release to contain both the NFS/RDMA client and server was
+ Linux 2.6.25 Therefore, a distribution compatible with this and subsequent
+ Linux kernel release should be installed.
+
+ The procedures described in this document have been tested with
+ distributions from Red Hat's Fedora Project (http://fedora.redhat.com/).
+
+ - Install nfs-utils-1.1.1 or greater on the client
+
+ An NFS/RDMA mount point can only be obtained by using the mount.nfs
+ command in nfs-utils-1.1.1 or greater. To see which version of mount.nfs
+ you are using, type:
+
+ > /sbin/mount.nfs -V
+
+ If the version is less than 1.1.1 or the command does not exist,
+ then you will need to install the latest version of nfs-utils.
+
+ Download the latest package from:
+
+ http://www.kernel.org/pub/linux/utils/nfs
+
+ Uncompress the package and follow the installation instructions.
+
+ If you will not be using GSS and NFSv4, the installation process
+ can be simplified by disabling these features when running configure:
+
+ > ./configure --disable-gss --disable-nfsv4
+
+ For more information on this see the package's README and INSTALL files.
+
+ After building the nfs-utils package, there will be a mount.nfs binary in
+ the utils/mount directory. This binary can be used to initiate NFS v2, v3,
+ or v4 mounts. To initiate a v4 mount, the binary must be called mount.nfs4.
+ The standard technique is to create a symlink called mount.nfs4 to mount.nfs.
+
+ NOTE: mount.nfs and therefore nfs-utils-1.1.1 or greater is only needed
+ on the NFS client machine. You do not need this specific version of
+ nfs-utils on the server. Furthermore, only the mount.nfs command from
+ nfs-utils-1.1.1 is needed on the client.
+
+ - Install a Linux kernel with NFS/RDMA
+
+ The NFS/RDMA client and server are both included in the mainline Linux
+ kernel version 2.6.25 and later. This and other versions of the 2.6 Linux
+ kernel can be found at:
+
+ ftp://ftp.kernel.org/pub/linux/kernel/v2.6/
+
+ Download the sources and place them in an appropriate location.
+
+ - Configure the RDMA stack
+
+ Make sure your kernel configuration has RDMA support enabled. Under
+ Device Drivers -> InfiniBand support, update the kernel configuration
+ to enable InfiniBand support [NOTE: the option name is misleading. Enabling
+ InfiniBand support is required for all RDMA devices (IB, iWARP, etc.)].
+
+ Enable the appropriate IB HCA support (mlx4, mthca, ehca, ipath, etc.) or
+ iWARP adapter support (amso, cxgb3, etc.).
+
+ If you are using InfiniBand, be sure to enable IP-over-InfiniBand support.
+
+ - Configure the NFS client and server
+
+ Your kernel configuration must also have NFS file system support and/or
+ NFS server support enabled. These and other NFS related configuration
+ options can be found under File Systems -> Network File Systems.
+
+ - Build, install, reboot
+
+ The NFS/RDMA code will be enabled automatically if NFS and RDMA
+ are turned on. The NFS/RDMA client and server are configured via the hidden
+ SUNRPC_XPRT_RDMA config option that depends on SUNRPC and INFINIBAND. The
+ value of SUNRPC_XPRT_RDMA will be:
+
+ - N if either SUNRPC or INFINIBAND are N, in this case the NFS/RDMA client
+ and server will not be built
+ - M if both SUNRPC and INFINIBAND are on (M or Y) and at least one is M,
+ in this case the NFS/RDMA client and server will be built as modules
+ - Y if both SUNRPC and INFINIBAND are Y, in this case the NFS/RDMA client
+ and server will be built into the kernel
+
+ Therefore, if you have followed the steps above and turned no NFS and RDMA,
+ the NFS/RDMA client and server will be built.
+
+ Build a new kernel, install it, boot it.
+
+Check RDMA and NFS Setup
+~~~~~~~~~~~~~~~~~~~~~~~~
+
+ Before configuring the NFS/RDMA software, it is a good idea to test
+ your new kernel to ensure that the kernel is working correctly.
+ In particular, it is a good idea to verify that the RDMA stack
+ is functioning as expected and standard NFS over TCP/IP and/or UDP/IP
+ is working properly.
+
+ - Check RDMA Setup
+
+ If you built the RDMA components as modules, load them at
+ this time. For example, if you are using a Mellanox Tavor/Sinai/Arbel
+ card:
+
+ > modprobe ib_mthca
+ > modprobe ib_ipoib
+
+ If you are using InfiniBand, make sure there is a Subnet Manager (SM)
+ running on the network. If your IB switch has an embedded SM, you can
+ use it. Otherwise, you will need to run an SM, such as OpenSM, on one
+ of your end nodes.
+
+ If an SM is running on your network, you should see the following:
+
+ > cat /sys/class/infiniband/driverX/ports/1/state
+ 4: ACTIVE
+
+ where driverX is mthca0, ipath5, ehca3, etc.
+
+ To further test the InfiniBand software stack, use IPoIB (this
+ assumes you have two IB hosts named host1 and host2):
+
+ host1> ifconfig ib0 a.b.c.x
+ host2> ifconfig ib0 a.b.c.y
+ host1> ping a.b.c.y
+ host2> ping a.b.c.x
+
+ For other device types, follow the appropriate procedures.
+
+ - Check NFS Setup
+
+ For the NFS components enabled above (client and/or server),
+ test their functionality over standard Ethernet using TCP/IP or UDP/IP.
+
+NFS/RDMA Setup
+~~~~~~~~~~~~~~
+
+ We recommend that you use two machines, one to act as the client and
+ one to act as the server.
+
+ One time configuration:
+
+ - On the server system, configure the /etc/exports file and
+ start the NFS/RDMA server.
+
+ Exports entries with the following format have been tested:
+
+ /vol0 10.97.103.47(rw,async) 192.168.0.47(rw,async,insecure,no_root_squash)
+
+ Here the first IP address is the client's Ethernet address and the second
+ IP address is the clients IPoIB address.
+
+ Each time a machine boots:
+
+ - Load and configure the RDMA drivers
+
+ For InfiniBand using a Mellanox adapter:
+
+ > modprobe ib_mthca
+ > modprobe ib_ipoib
+ > ifconfig ib0 a.b.c.d
+
+ NOTE: use unique addresses for the client and server
+
+ - Start the NFS server
+
+ If the NFS/RDMA server was built as a module (CONFIG_SUNRPC_XPRT_RDMA=m in kernel config),
+ load the RDMA transport module:
+
+ > modprobe svcrdma
+
+ Regardless of how the server was built (module or built-in), start the server:
+
+ > /etc/init.d/nfs start
+
+ or
+
+ > service nfs start
+
+ Instruct the server to listen on the RDMA transport:
+
+ > echo rdma 2050 > /proc/fs/nfsd/portlist
+
+ - On the client system
+
+ If the NFS/RDMA client was built as a module (CONFIG_SUNRPC_XPRT_RDMA=m in kernel config),
+ load the RDMA client module:
+
+ > modprobe xprtrdma.ko
+
+ Regardless of how the client was built (module or built-in), issue the mount.nfs command:
+
+ > /path/to/your/mount.nfs <IPoIB-server-name-or-address>:/<export> /mnt -i -o rdma,port=2050
+
+ To verify that the mount is using RDMA, run "cat /proc/mounts" and check the
+ "proto" field for the given mount.
+
+ Congratulations! You're using NFS/RDMA!
control correctly. If you have problems regarding this, try
another ALSA compliant mixer (alsamixer works).
+ Module snd-aw2
+ --------------
+
+ Module for Audiowerk2 sound card
+
+ This module supports multiple cards.
+
Module snd-azt2320
------------------
hippo_1 Hippo (Benq) with jack detection
sony-assamd Sony ASSAMD
ultra Samsung Q1 Ultra Vista model
+ lenovo-3000 Lenovo 3000 y410
basic fixed pin assignment w/o SPDIF
auto auto-config reading BIOS (default)
- ALC268
+ ALC267/268
+ quanta-il1 Quanta IL1 mini-notebook
3stack 3-stack model
toshiba Toshiba A205
acer Acer laptops
dell Dell OEM laptops (Vostro 1200)
+ zepto Zepto laptops
test for testing/debugging purpose, almost all controls can
adjusted. Appearing only when compiled with
$CONFIG_SND_DEBUG=y
auto auto-config reading BIOS (default)
+ ALC269
+ basic Basic preset
+
ALC662
3stack-dig 3-stack (2-channel) with SPDIF
3stack-6ch 3-stack (6-channel)
lenovo-nb0763 Lenovo NB0763
lenovo-ms7195-dig Lenovo MS7195
haier-w66 Haier W66
- 6stack-hp HP machines with 6stack (Nettle boards)
3stack-hp HP machines with 3stack (Lucknow, Samba boards)
6stack-dell Dell machines with 6stack (Inspiron 530)
mitac Mitac 8252D
+ clevo-m720 Clevo M720 laptop series
+ fujitsu-pi2515 Fujitsu AMILO Pi2515
auto auto-config reading BIOS (default)
ALC861/660
3stack 3-stack mode (default)
6stack 6-stack mode
+ AD1884A / AD1883 / AD1984A / AD1984B
+ desktop 3-stack desktop (default)
+ laptop laptop with HP jack sensing
+ mobile mobile devices with HP jack sensing
+ thinkpad Lenovo Thinkpad X300
+
AD1884
N/A
laptop-automute 2-channel with EAPD and HP-automute (Lenovo N100)
ultra 2-channel with EAPD (Samsung Ultra tablet PC)
- AD1988
+ AD1988/AD1988B/AD1989A/AD1989B
6stack 6-jack
6stack-dig ditto with SPDIF
3stack 3-jack
dell-m26 Dell Inspiron 1501
dell-m27 Dell Inspiron E1705/9400
gateway Gateway laptops with EAPD control
+ panasonic Panasonic CF-74
STAC9205/9254
ref Reference board
3stack D965 3stack
5stack D965 5stack + SPDIF
dell-3stack Dell Dimension E520
+ dell-bios Fixes with Dell BIOS setup
+
+ STAC92HD71B*
+ ref Reference board
+ dell-m4-1 Dell desktops
+ dell-m4-2 Dell desktops
+
+ STAC92HD73*
+ ref Reference board
+ dell-m6 Dell desktops
STAC9872
vaio Setup for VAIO FE550G/SZ110
Power management is _not_ supported.
+ Module snd-pcsp
+ -----------------
+
+ Module for internal PC-Speaker.
+
+ nforce_wa - enable NForce chipset workaround. Expect bad sound.
+
+ This module supports system beeps, some kind of PCM playback and
+ even a few mixer controls.
+
Module snd-pcxhr
----------------
--- /dev/null
+ 0 -> Unknown board (au0828)
+ 1 -> Hauppauge HVR950Q (au0828) [2040:7200]
+ 2 -> Hauppauge HVR850 (au0828) [2040:7240]
+ 3 -> DViCO FusionHDTV USB (au0828) [0fe9:d620]
147 -> VoodooTV 200 (USA) [121a:3000]
148 -> DViCO FusionHDTV 2 [dbc0:d200]
149 -> Typhoon TV-Tuner PCI (50684)
+150 -> Geovision GV-600 [008a:763c]
+151 -> Kozumi KTV-01C
4 -> DViCO FusionHDTV5 Express [18ac:d500]
5 -> Hauppauge WinTV-HVR1500Q [0070:7790,0070:7797]
6 -> Hauppauge WinTV-HVR1500 [0070:7710,0070:7717]
+ 7 -> Hauppauge WinTV-HVR1200 [0070:71d1]
+ 8 -> Hauppauge WinTV-HVR1700 [0070:8101]
+ 9 -> Hauppauge WinTV-HVR1400 [0070:8010]
56 -> Hauppauge WinTV-HVR1300 DVB-T/Hybrid MPEG Encoder [0070:9600,0070:9601,0070:9602]
57 -> ADS Tech Instant Video PCI [1421:0390]
58 -> Pinnacle PCTV HD 800i [11bd:0051]
+ 59 -> DViCO FusionHDTV 5 PCI nano [18ac:d530]
+ 60 -> Pinnacle Hybrid PCTV [12ab:1788]
+ 61 -> Winfast TV2000 XP Global [107d:6f18]
+ 62 -> PowerColor Real Angel 330 [14f1:ea3d]
+ 63 -> Geniatech X8000-MT DVBT [14f1:8852]
+ 64 -> DViCO FusionHDTV DVB-T PRO [18ac:db30]
+ 65 -> DViCO FusionHDTV 7 Gold [18ac:d610]
+ 66 -> Prolink Pixelview MPEG 8000GT [1554:4935]
+ 67 -> Kworld PlusTV HD PCI 120 (ATSC 120) [17de:08c1]
24 -> KNC One TV-Station DVR [1894:a006]
25 -> ASUS TV-FM 7133 [1043:4843]
26 -> Pinnacle PCTV Stereo (saa7134) [11bd:002b]
- 27 -> Manli MuchTV M-TV002/Behold TV 403 FM
- 28 -> Manli MuchTV M-TV001/Behold TV 401
+ 27 -> Manli MuchTV M-TV002
+ 28 -> Manli MuchTV M-TV001
29 -> Nagase Sangyo TransGear 3000TV [1461:050c]
30 -> Elitegroup ECS TVP3XP FM1216 Tuner Card(PAL-BG,FM) [1019:4cb4]
31 -> Elitegroup ECS TVP3XP FM1236 Tuner Card (NTSC,FM) [1019:4cb5]
130 -> Beholder BeholdTV M6 / BeholdTV M6 Extra [5ace:6190,5ace:6193]
131 -> Twinhan Hybrid DTV-DVB 3056 PCI [1822:0022]
132 -> Genius TVGO AM11MCE
+133 -> NXP Snake DVB-S reference design
+134 -> Medion/Creatix CTX953 Hybrid [16be:0010]
+135 -> MSI TV@nywhere A/D v1.1 [1462:8625]
+136 -> AVerMedia Cardbus TV/Radio (E506R) [1461:f436]
+137 -> AVerMedia Hybrid TV/Radio (A16D) [1461:f936]
+138 -> Avermedia M115 [1461:a836]
+139 -> Compro VideoMate T750 [185b:c900]
+140 -> Avermedia DVB-S Pro A700 [1461:a7a1]
+141 -> Avermedia DVB-S Hybrid+FM A700 [1461:a7a2]
write_hunk(812664, 192);
#
- # Firmware 58, type: SCODE FW HAS IF (0x60000000), IF = 4.50 MHz id: NTSC/M Jp (0000000000002000), size: 192
+ # Firmware 58, type: SCODE FW MTS LCD NOGD MONO IF HAS IF (0x6002b004), IF = 4.50 MHz id: NTSC PAL/M PAL/N (000000000000b700), size: 192
#
- write_le32(0x60000000); # Type
- write_le64(0x00000000, 0x00002000); # ID
+ write_le32(0x6002b004); # Type
+ write_le64(0x00000000, 0x0000b700); # ID
write_le16(4500); # IF
write_le32(192); # Size
write_hunk(807672, 192);
write_hunk(807864, 192);
#
- # Firmware 60, type: SCODE FW DTV78 ZARLINK456 HAS IF (0x62000100), IF = 4.76 MHz id: (0000000000000000), size: 192
+ # Firmware 60, type: SCODE FW DTV6 QAM DTV7 DTV78 DTV8 ZARLINK456 HAS IF (0x620003e0), IF = 4.76 MHz id: (0000000000000000), size: 192
#
- write_le32(0x62000100); # Type
+ write_le32(0x620003e0); # Type
write_le64(0x00000000, 0x00000000); # ID
write_le16(4760); # IF
write_le32(192); # Size
write_hunk(811512, 192);
#
- # Firmware 62, type: SCODE FW DTV7 ZARLINK456 HAS IF (0x62000080), IF = 5.26 MHz id: (0000000000000000), size: 192
+ # Firmware 62, type: SCODE FW HAS IF (0x60000000), IF = 5.26 MHz id: (0000000000000000), size: 192
#
- write_le32(0x62000080); # Type
+ write_le32(0x60000000); # Type
write_le64(0x00000000, 0x00000000); # ID
write_le16(5260); # IF
write_le32(192); # Size
write_hunk(810552, 192);
#
- # Firmware 63, type: SCODE FW MONO HAS IF (0x60008000), IF = 5.32 MHz id: PAL/BG NICAM/B (0000000800000007), size: 192
+ # Firmware 63, type: SCODE FW MONO HAS IF (0x60008000), IF = 5.32 MHz id: PAL/BG A2 NICAM (0000000f00000007), size: 192
#
write_le32(0x60008000); # Type
- write_le64(0x00000008, 0x00000007); # ID
+ write_le64(0x0000000f, 0x00000007); # ID
write_le16(5320); # IF
write_le32(192); # Size
write_hunk(810744, 192);
#
- # Firmware 64, type: SCODE FW DTV8 CHINA HAS IF (0x64000200), IF = 5.40 MHz id: (0000000000000000), size: 192
+ # Firmware 64, type: SCODE FW DTV7 DTV78 DTV8 DIBCOM52 CHINA HAS IF (0x65000380), IF = 5.40 MHz id: (0000000000000000), size: 192
#
- write_le32(0x64000200); # Type
+ write_le32(0x65000380); # Type
write_le64(0x00000000, 0x00000000); # ID
write_le16(5400); # IF
write_le32(192); # Size
write_hunk(809592, 192);
#
- # Firmware 66, type: SCODE FW HAS IF (0x60000000), IF = 5.64 MHz id: PAL/BG A2/B (0000000200000007), size: 192
+ # Firmware 66, type: SCODE FW HAS IF (0x60000000), IF = 5.64 MHz id: PAL/BG A2 (0000000300000007), size: 192
#
write_le32(0x60000000); # Type
- write_le64(0x00000002, 0x00000007); # ID
+ write_le64(0x00000003, 0x00000007); # ID
write_le16(5640); # IF
write_le32(192); # Size
write_hunk(808440, 192);
#
- # Firmware 67, type: SCODE FW HAS IF (0x60000000), IF = 5.74 MHz id: PAL/BG NICAM/B (0000000800000007), size: 192
+ # Firmware 67, type: SCODE FW HAS IF (0x60000000), IF = 5.74 MHz id: PAL/BG NICAM (0000000c00000007), size: 192
#
write_le32(0x60000000); # Type
- write_le64(0x00000008, 0x00000007); # ID
+ write_le64(0x0000000c, 0x00000007); # ID
write_le16(5740); # IF
write_le32(192); # Size
write_hunk(808632, 192);
#
- # Firmware 68, type: SCODE FW DTV7 DIBCOM52 HAS IF (0x61000080), IF = 5.90 MHz id: (0000000000000000), size: 192
+ # Firmware 68, type: SCODE FW HAS IF (0x60000000), IF = 5.90 MHz id: (0000000000000000), size: 192
#
- write_le32(0x61000080); # Type
+ write_le32(0x60000000); # Type
write_le64(0x00000000, 0x00000000); # ID
write_le16(5900); # IF
write_le32(192); # Size
write_hunk(810360, 192);
#
- # Firmware 69, type: SCODE FW MONO HAS IF (0x60008000), IF = 6.00 MHz id: PAL/I (0000000000000010), size: 192
+ # Firmware 69, type: SCODE FW MONO HAS IF (0x60008000), IF = 6.00 MHz id: PAL/DK PAL/I SECAM/K3 SECAM/L SECAM/Lc NICAM (0000000c04c000f0), size: 192
#
write_le32(0x60008000); # Type
- write_le64(0x00000000, 0x00000010); # ID
+ write_le64(0x0000000c, 0x04c000f0); # ID
write_le16(6000); # IF
write_le32(192); # Size
write_hunk(808824, 192);
#
- # Firmware 70, type: SCODE FW DTV6 QAM F6MHZ HAS IF (0x68000060), IF = 6.20 MHz id: (0000000000000000), size: 192
+ # Firmware 70, type: SCODE FW DTV6 QAM ATSC LG60 F6MHZ HAS IF (0x68050060), IF = 6.20 MHz id: (0000000000000000), size: 192
#
- write_le32(0x68000060); # Type
+ write_le32(0x68050060); # Type
write_le64(0x00000000, 0x00000000); # ID
write_le16(6200); # IF
write_le32(192); # Size
write_hunk(809208, 192);
#
- # Firmware 74, type: SCODE FW MONO HAS IF (0x60008000), IF = 6.50 MHz id: SECAM/K3 (0000000004000000), size: 192
+ # Firmware 74, type: SCODE FW MONO HAS IF (0x60008000), IF = 6.50 MHz id: PAL/DK SECAM/K3 SECAM/L NICAM (0000000c044000e0), size: 192
#
write_le32(0x60008000); # Type
- write_le64(0x00000000, 0x04000000); # ID
+ write_le64(0x0000000c, 0x044000e0); # ID
write_le16(6500); # IF
write_le32(192); # Size
write_hunk(811128, 192);
S: Maintained
MAC80211
-P: Michael Wu
-M: flamingice@sourmilk.net
P: Johannes Berg
M: johannes@sipsolutions.net
-P: Jiri Benc
-M: jbenc@suse.cz
+P: Michael Wu
+M: flamingice@sourmilk.net
L: linux-wireless@vger.kernel.org
W: http://linuxwireless.org/
T: git kernel.org:/pub/scm/linux/kernel/git/linville/wireless-2.6.git
lock_kernel();
mm = current->mm;
mm->end_code = bss_start + bss_len;
+ mm->start_brk = bss_start + bss_len;
mm->brk = bss_start + bss_len;
#if 0
printk("set_program_attributes(%lx %lx %lx %lx)\n",
static void __init
quirk_cypress(struct pci_dev *dev)
{
- /* The Notorious Cy82C693 chip. */
-
- /* The Cypress IDE controller doesn't support native mode, but it
- has programmable addresses of IDE command/control registers.
- This violates PCI specifications, confuses the IDE subsystem and
- causes resource conflicts between the primary HD_CMD register and
- the floppy controller. Ugh. Fix that. */
- if (dev->class >> 8 == PCI_CLASS_STORAGE_IDE) {
- dev->resource[0].flags = 0;
- dev->resource[1].flags = 0;
- }
-
/* The Cypress bridge responds on the PCI bus in the address range
0xffff0000-0xffffffff (conventional x86 BIOS ROM). There is no
way to turn this off. The bridge also supports several extended
BIOS ranges (disabled after power-up), and some consoles do turn
them on. So if we use a large direct-map window, or a large SG
window, we must avoid the entire 0xfff00000-0xffffffff region. */
- else if (dev->class >> 8 == PCI_CLASS_BRIDGE_ISA) {
+ if (dev->class >> 8 == PCI_CLASS_BRIDGE_ISA) {
if (__direct_map_base + __direct_map_size >= 0xfff00000UL)
__direct_map_size = 0xfff00000UL - __direct_map_base;
else {
pci_write_config_byte(dev, PCI_LATENCY_TIMER, 64);
}
-static void __init
+void __init
pcibios_claim_one_bus(struct pci_bus *b)
{
struct pci_dev *dev;
if (r->parent || !r->start || !r->flags)
continue;
- pci_claim_resource(dev, i);
+ if (pci_probe_only || (r->flags & IORESOURCE_PCI_FIXED))
+ pci_claim_resource(dev, i);
}
}
}
}
- if (pci_probe_only)
- pcibios_claim_console_setup();
+ pcibios_claim_console_setup();
pci_assign_unassigned_resources();
pci_fixup_irqs(alpha_mv.pci_swizzle, alpha_mv.pci_map_irq);
}
extern void free_reserved_mem(void *, void *);
+extern void pcibios_claim_one_bus(struct pci_bus *);
static struct resource irongate_mem = {
.name = "Irongate PCI MEM",
/* Scan our single hose. */
bus = pci_scan_bus(0, alpha_mv.pci_ops, hose);
hose->bus = bus;
+ pcibios_claim_one_bus(bus);
irongate = pci_get_bus_and_slot(0, 0);
bus->self = irongate;
xtime.tv_sec = __raw_readl(rtc_base + RTC_DR);
+ /* note that 'dev' is merely used for irq disambiguation;
+ * it is not actually referenced in the irq handler
+ */
ret = request_irq(dev->irq[0], arm_rtc_interrupt, IRQF_DISABLED,
- "rtc-pl030", NULL);
+ "rtc-pl030", dev);
if (ret)
goto map_out;
{
u32 mask = CPLD_LATCHED_INTS;
irq = IRQ_KEV7A400_CPLD;
- for (; mask; mask >>= 1, ++irq) {
+ for (; mask; mask >>= 1, ++irq)
if (mask & 1)
- desc[irq].handle (irq, desc);
- }
+ desc_handle_irq(irq, desc);
}
void __init lh7a40x_init_board_irq (void)
depends on !MMU
select CPU_32v4T
select CPU_ABRT_LV4T
+ select CPU_PABRT_NOIFAR
select CPU_CACHE_V4
help
A 32-bit RISC microprocessor based on the ARM7 processor core
depends on !MMU
select CPU_32v4T
select CPU_ABRT_LV4T
+ select CPU_PABRT_NOIFAR
select CPU_CACHE_V3 # although the core is v4t
select CPU_CP15_MPU
help
depends on !MMU
select CPU_32v4T
select CPU_ABRT_NOMMU
+ select CPU_PABRT_NOIFAR
select CPU_CACHE_V4
help
A 32-bit RISC microprocessor based on the ARM9 processor core
depends on !MMU
select CPU_32v4T
select CPU_ABRT_NOMMU
+ select CPU_PABRT_NOIFAR
select CPU_CACHE_VIVT
select CPU_CP15_MPU
help
depends on !MMU
select CPU_32v5
select CPU_ABRT_NOMMU
+ select CPU_PABRT_NOIFAR
select CPU_CACHE_VIVT
select CPU_CP15_MPU
help
default y
select CPU_32v5
select CPU_ABRT_EV5T
+ select CPU_PABRT_NOIFAR
select CPU_CACHE_VIVT
select CPU_CP15_MMU
select CPU_TLB_V4WBI if MMU
.type arm1020_processor_functions, #object
arm1020_processor_functions:
.word v4t_early_abort
+ .word pabort_noifar
.word cpu_arm1020_proc_init
.word cpu_arm1020_proc_fin
.word cpu_arm1020_reset
.word cpu_arm1020_dcache_clean_area
.word cpu_arm1020_switch_mm
.word cpu_arm1020_set_pte_ext
- .word pabort_noifar
.size arm1020_processor_functions, . - arm1020_processor_functions
.section ".rodata"
.type arm1020e_processor_functions, #object
arm1020e_processor_functions:
.word v4t_early_abort
+ .word pabort_noifar
.word cpu_arm1020e_proc_init
.word cpu_arm1020e_proc_fin
.word cpu_arm1020e_reset
.word cpu_arm1020e_dcache_clean_area
.word cpu_arm1020e_switch_mm
.word cpu_arm1020e_set_pte_ext
- .word pabort_noifar
.size arm1020e_processor_functions, . - arm1020e_processor_functions
.section ".rodata"
.type arm1022_processor_functions, #object
arm1022_processor_functions:
.word v4t_early_abort
+ .word pabort_noifar
.word cpu_arm1022_proc_init
.word cpu_arm1022_proc_fin
.word cpu_arm1022_reset
.word cpu_arm1022_dcache_clean_area
.word cpu_arm1022_switch_mm
.word cpu_arm1022_set_pte_ext
- .word pabort_noifar
.size arm1022_processor_functions, . - arm1022_processor_functions
.section ".rodata"
.type arm1026_processor_functions, #object
arm1026_processor_functions:
.word v5t_early_abort
+ .word pabort_noifar
.word cpu_arm1026_proc_init
.word cpu_arm1026_proc_fin
.word cpu_arm1026_reset
.word cpu_arm1026_dcache_clean_area
.word cpu_arm1026_switch_mm
.word cpu_arm1026_set_pte_ext
- .word pabort_noifar
.size arm1026_processor_functions, . - arm1026_processor_functions
.section .rodata
.type arm6_processor_functions, #object
ENTRY(arm6_processor_functions)
.word cpu_arm6_data_abort
+ .word pabort_noifar
.word cpu_arm6_proc_init
.word cpu_arm6_proc_fin
.word cpu_arm6_reset
.word cpu_arm6_dcache_clean_area
.word cpu_arm6_switch_mm
.word cpu_arm6_set_pte_ext
- .word pabort_noifar
.size arm6_processor_functions, . - arm6_processor_functions
/*
.type arm7_processor_functions, #object
ENTRY(arm7_processor_functions)
.word cpu_arm7_data_abort
+ .word pabort_noifar
.word cpu_arm7_proc_init
.word cpu_arm7_proc_fin
.word cpu_arm7_reset
.word cpu_arm7_dcache_clean_area
.word cpu_arm7_switch_mm
.word cpu_arm7_set_pte_ext
- .word pabort_noifar
.size arm7_processor_functions, . - arm7_processor_functions
.section ".rodata"
.type arm720_processor_functions, #object
ENTRY(arm720_processor_functions)
.word v4t_late_abort
+ .word pabort_noifar
.word cpu_arm720_proc_init
.word cpu_arm720_proc_fin
.word cpu_arm720_reset
.word cpu_arm720_dcache_clean_area
.word cpu_arm720_switch_mm
.word cpu_arm720_set_pte_ext
- .word pabort_noifar
.size arm720_processor_functions, . - arm720_processor_functions
.section ".rodata"
.type arm740_processor_functions, #object
ENTRY(arm740_processor_functions)
.word v4t_late_abort
+ .word pabort_noifar
.word cpu_arm740_proc_init
.word cpu_arm740_proc_fin
.word cpu_arm740_reset
.type arm7tdmi_processor_functions, #object
ENTRY(arm7tdmi_processor_functions)
.word v4t_late_abort
+ .word pabort_noifar
.word cpu_arm7tdmi_proc_init
.word cpu_arm7tdmi_proc_fin
.word cpu_arm7tdmi_reset
.type arm920_processor_functions, #object
arm920_processor_functions:
.word v4t_early_abort
+ .word pabort_noifar
.word cpu_arm920_proc_init
.word cpu_arm920_proc_fin
.word cpu_arm920_reset
.word cpu_arm920_dcache_clean_area
.word cpu_arm920_switch_mm
.word cpu_arm920_set_pte_ext
- .word pabort_noifar
.size arm920_processor_functions, . - arm920_processor_functions
.section ".rodata"
.type arm922_processor_functions, #object
arm922_processor_functions:
.word v4t_early_abort
+ .word pabort_noifar
.word cpu_arm922_proc_init
.word cpu_arm922_proc_fin
.word cpu_arm922_reset
.word cpu_arm922_dcache_clean_area
.word cpu_arm922_switch_mm
.word cpu_arm922_set_pte_ext
- .word pabort_noifar
.size arm922_processor_functions, . - arm922_processor_functions
.section ".rodata"
.type arm925_processor_functions, #object
arm925_processor_functions:
.word v4t_early_abort
+ .word pabort_noifar
.word cpu_arm925_proc_init
.word cpu_arm925_proc_fin
.word cpu_arm925_reset
.word cpu_arm925_dcache_clean_area
.word cpu_arm925_switch_mm
.word cpu_arm925_set_pte_ext
- .word pabort_noifar
.size arm925_processor_functions, . - arm925_processor_functions
.section ".rodata"
.type arm926_processor_functions, #object
arm926_processor_functions:
.word v5tj_early_abort
+ .word pabort_noifar
.word cpu_arm926_proc_init
.word cpu_arm926_proc_fin
.word cpu_arm926_reset
.word cpu_arm926_dcache_clean_area
.word cpu_arm926_switch_mm
.word cpu_arm926_set_pte_ext
- .word pabort_noifar
.size arm926_processor_functions, . - arm926_processor_functions
.section ".rodata"
.type arm940_processor_functions, #object
ENTRY(arm940_processor_functions)
.word nommu_early_abort
+ .word pabort_noifar
.word cpu_arm940_proc_init
.word cpu_arm940_proc_fin
.word cpu_arm940_reset
.type arm946_processor_functions, #object
ENTRY(arm946_processor_functions)
.word nommu_early_abort
+ .word pabort_noifar
.word cpu_arm946_proc_init
.word cpu_arm946_proc_fin
.word cpu_arm946_reset
.type arm9tdmi_processor_functions, #object
ENTRY(arm9tdmi_processor_functions)
.word nommu_early_abort
+ .word pabort_noifar
.word cpu_arm9tdmi_proc_init
.word cpu_arm9tdmi_proc_fin
.word cpu_arm9tdmi_reset
.type feroceon_processor_functions, #object
feroceon_processor_functions:
.word v5t_early_abort
+ .word pabort_noifar
.word cpu_feroceon_proc_init
.word cpu_feroceon_proc_fin
.word cpu_feroceon_reset
.word cpu_feroceon_dcache_clean_area
.word cpu_feroceon_switch_mm
.word cpu_feroceon_set_pte_ext
- .word pabort_noifar
.size feroceon_processor_functions, . - feroceon_processor_functions
.section ".rodata"
.type sa110_processor_functions, #object
ENTRY(sa110_processor_functions)
.word v4_early_abort
+ .word pabort_noifar
.word cpu_sa110_proc_init
.word cpu_sa110_proc_fin
.word cpu_sa110_reset
.word cpu_sa110_dcache_clean_area
.word cpu_sa110_switch_mm
.word cpu_sa110_set_pte_ext
- .word pabort_noifar
.size sa110_processor_functions, . - sa110_processor_functions
.section ".rodata"
.type sa1100_processor_functions, #object
ENTRY(sa1100_processor_functions)
.word v4_early_abort
+ .word pabort_noifar
.word cpu_sa1100_proc_init
.word cpu_sa1100_proc_fin
.word cpu_sa1100_reset
.word cpu_sa1100_dcache_clean_area
.word cpu_sa1100_switch_mm
.word cpu_sa1100_set_pte_ext
- .word pabort_noifar
.size sa1100_processor_functions, . - sa1100_processor_functions
.section ".rodata"
.type v6_processor_functions, #object
ENTRY(v6_processor_functions)
.word v6_early_abort
+ .word pabort_noifar
.word cpu_v6_proc_init
.word cpu_v6_proc_fin
.word cpu_v6_reset
.word cpu_v6_dcache_clean_area
.word cpu_v6_switch_mm
.word cpu_v6_set_pte_ext
- .word pabort_noifar
.size v6_processor_functions, . - v6_processor_functions
.type cpu_arch_name, #object
.type v7_processor_functions, #object
ENTRY(v7_processor_functions)
.word v7_early_abort
+ .word pabort_ifar
.word cpu_v7_proc_init
.word cpu_v7_proc_fin
.word cpu_v7_reset
.word cpu_v7_dcache_clean_area
.word cpu_v7_switch_mm
.word cpu_v7_set_pte_ext
- .word pabort_ifar
.size v7_processor_functions, . - v7_processor_functions
.type cpu_arch_name, #object
.type xsc3_processor_functions, #object
ENTRY(xsc3_processor_functions)
.word v5t_early_abort
+ .word pabort_noifar
.word cpu_xsc3_proc_init
.word cpu_xsc3_proc_fin
.word cpu_xsc3_reset
.type xscale_processor_functions, #object
ENTRY(xscale_processor_functions)
.word v5t_early_abort
+ .word pabort_noifar
.word cpu_xscale_proc_init
.word cpu_xscale_proc_fin
.word cpu_xscale_reset
.word cpu_xscale_dcache_clean_area
.word cpu_xscale_switch_mm
.word cpu_xscale_set_pte_ext
- .word pabort_noifar
.size xscale_processor_functions, . - xscale_processor_functions
.section ".rodata"
bool
default y
-config GENERIC_TIME
- bool
- default n
-
config GENERIC_GPIO
bool
default y
depends on (BF542 || BF544 || BF547 || BF548 || BF549)
default y
-config BFIN_DUAL_CORE
- bool
- depends on (BF561)
- default y
-
-config BFIN_SINGLE_CORE
- bool
- depends on !BFIN_DUAL_CORE
- default y
-
config MEM_GENERIC_BOARD
bool
depends on GENERIC_BOARD
config MEM_MT48LC32M16A2TG_75
bool
- depends on (BFIN527_EZKIT)
+ depends on (BFIN527_EZKIT || BFIN532_IP0X)
default y
source "arch/blackfin/mach-bf527/Kconfig"
to the kernel, you may specify one here. As a minimum, you should specify
the memory size and the root device (e.g., mem=8M, root=/dev/nfs).
+config BOOT_LOAD
+ hex "Kernel load address for booting"
+ default "0x1000"
+ range 0x1000 0x20000000
+ help
+ This option allows you to set the load address of the kernel.
+ This can be useful if you are on a board which has a small amount
+ of memory or you wish to reserve some memory at the beginning of
+ the address space.
+
+ Note that you need to keep this value above 4k (0x1000) as this
+ memory region is used to capture NULL pointer references as well
+ as some core kernel functions.
+
comment "Clock/PLL Setup"
config CLKIN_HZ
- int "Crystal Frequency in Hz"
+ int "Frequency of the crystal on the board in Hz"
default "11059200" if BFIN533_STAMP
default "27000000" if BFIN533_EZKIT
default "25000000" if (BFIN537_STAMP || BFIN527_EZKIT || H8606_HVSISTEMAS)
default "30000000" if BFIN561_EZKIT
default "24576000" if PNAV10
+ default "10000000" if BFIN532_IP0X
help
The frequency of CLKIN crystal oscillator on the board in Hz.
+ Warning: This value should match the crystal on the board. Otherwise,
+ peripherals won't work properly.
config BFIN_KERNEL_CLOCK
bool "Re-program Clocks while Kernel boots?"
are also not changed, and the Bootloader does 100% of the hardware
configuration.
+config MEM_SIZE
+ int "SDRAM Memory Size in MBytes"
+ depends on BFIN_KERNEL_CLOCK
+ default 64
+
+config MEM_ADD_WIDTH
+ int "Memory Address Width"
+ depends on BFIN_KERNEL_CLOCK
+ depends on (!BF54x)
+ range 8 11
+ default 9 if BFIN533_EZKIT
+ default 9 if BFIN561_EZKIT
+ default 9 if H8606_HVSISTEMAS
+ default 10 if BFIN527_EZKIT
+ default 10 if BFIN537_STAMP
+ default 11 if BFIN533_STAMP
+ default 10 if PNAV10
+ default 10 if BFIN532_IP0X
+
config PLL_BYPASS
bool "Bypass PLL"
depends on BFIN_KERNEL_CLOCK
range 1 64
default "22" if BFIN533_EZKIT
default "45" if BFIN533_STAMP
- default "20" if (BFIN537_STAMP || BFIN527_EZKIT || BFIN548_EZKIT)
+ default "20" if (BFIN537_STAMP || BFIN527_EZKIT || BFIN548_EZKIT || BFIN548_BLUETECHNIX_CM)
default "22" if BFIN533_BLUETECHNIX_CM
default "20" if BFIN537_BLUETECHNIX_CM
default "20" if BFIN561_BLUETECHNIX_CM
int "System Clock Divider"
depends on BFIN_KERNEL_CLOCK
range 1 15
- default 5 if BFIN533_EZKIT
- default 5 if BFIN533_STAMP
- default 4 if (BFIN537_STAMP || BFIN527_EZKIT || BFIN548_EZKIT)
- default 5 if BFIN533_BLUETECHNIX_CM
- default 4 if BFIN537_BLUETECHNIX_CM
- default 4 if BFIN561_BLUETECHNIX_CM
- default 5 if BFIN561_EZKIT
- default 3 if H8606_HVSISTEMAS
+ default 5
help
This sets the frequency of the system clock (including SDRAM or DDR).
This can be between 1 and 15
System Clock = (PLL frequency) / (this setting)
+config MAX_MEM_SIZE
+ int "Max SDRAM Memory Size in MBytes"
+ depends on !BFIN_KERNEL_CLOCK && !MPU
+ default 512
+ help
+ This is the max memory size that the kernel will create CPLB
+ tables for. Your system will not be able to handle any more.
+
+choice
+ prompt "DDR SDRAM Chip Type"
+ depends on BFIN_KERNEL_CLOCK
+ depends on BF54x
+ default MEM_MT46V32M16_5B
+
+config MEM_MT46V32M16_6T
+ bool "MT46V32M16_6T"
+
+config MEM_MT46V32M16_5B
+ bool "MT46V32M16_5B"
+endchoice
+
#
# Max & Min Speeds for various Chips
#
source kernel/Kconfig.hz
-comment "Memory Setup"
-
-config MEM_SIZE
- int "SDRAM Memory Size in MBytes"
- default 32 if BFIN533_EZKIT
- default 64 if BFIN527_EZKIT
- default 64 if BFIN537_STAMP
- default 64 if BFIN548_EZKIT
- default 64 if BFIN561_EZKIT
- default 128 if BFIN533_STAMP
- default 64 if PNAV10
- default 32 if H8606_HVSISTEMAS
+config GENERIC_TIME
+ bool "Generic time"
+ default y
-config MEM_ADD_WIDTH
- int "SDRAM Memory Address Width"
- depends on (!BF54x)
- default 9 if BFIN533_EZKIT
- default 9 if BFIN561_EZKIT
- default 9 if H8606_HVSISTEMAS
- default 10 if BFIN527_EZKIT
- default 10 if BFIN537_STAMP
- default 11 if BFIN533_STAMP
- default 10 if PNAV10
+config GENERIC_CLOCKEVENTS
+ bool "Generic clock events"
+ depends on GENERIC_TIME
+ default y
+config CYCLES_CLOCKSOURCE
+ bool "Use 'CYCLES' as a clocksource (EXPERIMENTAL)"
+ depends on EXPERIMENTAL
+ depends on GENERIC_CLOCKEVENTS
+ depends on !BFIN_SCRATCH_REG_CYCLES
+ default n
+ help
+ If you say Y here, you will enable support for using the 'cycles'
+ registers as a clock source. Doing so means you will be unable to
+ safely write to the 'cycles' register during runtime. You will
+ still be able to read it (such as for performance monitoring), but
+ writing the registers will most likely crash the kernel.
-choice
- prompt "DDR SDRAM Chip Type"
- depends on BFIN548_EZKIT
- default MEM_MT46V32M16_5B
+source kernel/time/Kconfig
-config MEM_MT46V32M16_6T
- bool "MT46V32M16_6T"
+comment "Memory Setup"
-config MEM_MT46V32M16_5B
- bool "MT46V32M16_5B"
-endchoice
+comment "Misc"
config ENET_FLASH_PIN
int "PF port/pin used for flash and ethernet sharing"
code.
For example: PF0 --> 0,PF1 --> 1,PF2 --> 2, etc.
-config BOOT_LOAD
- hex "Kernel load address for booting"
- default "0x1000"
- range 0x1000 0x20000000
- help
- This option allows you to set the load address of the kernel.
- This can be useful if you are on a board which has a small amount
- of memory or you wish to reserve some memory at the beginning of
- the address space.
-
- Note that you need to keep this value above 4k (0x1000) as this
- memory region is used to capture NULL pointer references as well
- as some core kernel functions.
-
choice
prompt "Blackfin Exception Scratch Register"
default BFIN_SCRATCH_REG_RETN
source "mm/Kconfig"
-config LARGE_ALLOCS
- bool "Allow allocating large blocks (> 1MB) of memory"
- help
- Allow the slab memory allocator to keep chains for very large
- memory sizes - upto 32MB. You may need this if your system has
- a lot of RAM, and you need to able to allocate very large
- contiguous chunks. If unsure, say N.
-
config BFIN_GPTIMERS
tristate "Enable Blackfin General Purpose Timers API"
default n
KBUILD_CFLAGS += -mcpu=$(cpu-y)-$(rev-y)
KBUILD_AFLAGS += -mcpu=$(cpu-y)-$(rev-y)
+# - we utilize the silicon rev from the toolchain, so move it over to the checkflags
+# - the l1_text attribute is Blackfin specific, so fake it out as used to kill warnings
+CHECKFLAGS_SILICON = $(shell echo "" | $(CPP) $(KBUILD_CFLAGS) -dD - 2>/dev/null | awk '$$2 == "__SILICON_REVISION__" { print $$3 }')
+CHECKFLAGS += -D__SILICON_REVISION__=$(CHECKFLAGS_SILICON) -Dl1_text=__used__
+
head-y := arch/$(ARCH)/mach-$(MACHINE)/head.o arch/$(ARCH)/kernel/init_task.o
core-y += arch/$(ARCH)/kernel/ arch/$(ARCH)/mm/ arch/$(ARCH)/mach-common/
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
-# CONFIG_GENERIC_TIME is not set
+CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_GPIO=y
CONFIG_FORCE_MAX_ZONEORDER=14
CONFIG_GENERIC_CALIBRATE_DELAY=y
#
# Memory Setup
#
-CONFIG_MEM_SIZE=64
+CONFIG_MAX_MEM_SIZE=512
CONFIG_MEM_ADD_WIDTH=10
CONFIG_BOOT_LOAD=0x1000
CONFIG_BFIN_SCRATCH_REG_RETN=y
#
CONFIG_SERIAL_BFIN=y
CONFIG_SERIAL_BFIN_CONSOLE=y
-# CONFIG_SERIAL_BFIN_DMA is not set
-CONFIG_SERIAL_BFIN_PIO=y
+CONFIG_SERIAL_BFIN_DMA=y
+# CONFIG_SERIAL_BFIN_PIO is not set
# CONFIG_SERIAL_BFIN_UART0 is not set
CONFIG_SERIAL_BFIN_UART1=y
# CONFIG_BFIN_UART1_CTSRTS is not set
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
-# CONFIG_GENERIC_TIME is not set
+CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_GPIO=y
CONFIG_FORCE_MAX_ZONEORDER=14
CONFIG_GENERIC_CALIBRATE_DELAY=y
#
# Memory Setup
#
-CONFIG_MEM_SIZE=32
+CONFIG_MAX_MEM_SIZE=512
CONFIG_MEM_ADD_WIDTH=9
CONFIG_BOOT_LOAD=0x1000
CONFIG_BFIN_SCRATCH_REG_RETN=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
-# CONFIG_GENERIC_TIME is not set
+CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_GPIO=y
CONFIG_FORCE_MAX_ZONEORDER=14
CONFIG_GENERIC_CALIBRATE_DELAY=y
#
# Memory Setup
#
-CONFIG_MEM_SIZE=128
+CONFIG_MAX_MEM_SIZE=512
CONFIG_MEM_ADD_WIDTH=11
CONFIG_ENET_FLASH_PIN=0
CONFIG_BOOT_LOAD=0x1000
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
-# CONFIG_GENERIC_TIME is not set
+CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_GPIO=y
CONFIG_FORCE_MAX_ZONEORDER=14
CONFIG_GENERIC_CALIBRATE_DELAY=y
#
# Memory Setup
#
-CONFIG_MEM_SIZE=64
+CONFIG_MAX_MEM_SIZE=512
CONFIG_MEM_ADD_WIDTH=10
CONFIG_BOOT_LOAD=0x1000
CONFIG_BFIN_SCRATCH_REG_RETN=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
-# CONFIG_GENERIC_TIME is not set
+CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_GPIO=y
CONFIG_FORCE_MAX_ZONEORDER=14
CONFIG_GENERIC_CALIBRATE_DELAY=y
#
# Memory Setup
#
-CONFIG_MEM_SIZE=64
+CONFIG_MAX_MEM_SIZE=512
# CONFIG_MEM_MT46V32M16_6T is not set
CONFIG_MEM_MT46V32M16_5B=y
CONFIG_BOOT_LOAD=0x1000
#
CONFIG_SERIAL_BFIN=y
CONFIG_SERIAL_BFIN_CONSOLE=y
-# CONFIG_SERIAL_BFIN_DMA is not set
-CONFIG_SERIAL_BFIN_PIO=y
+CONFIG_SERIAL_BFIN_DMA=y
+# CONFIG_SERIAL_BFIN_PIO is not set
# CONFIG_SERIAL_BFIN_UART0 is not set
CONFIG_SERIAL_BFIN_UART1=y
# CONFIG_BFIN_UART1_CTSRTS is not set
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
-# CONFIG_GENERIC_TIME is not set
+CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_GPIO=y
CONFIG_FORCE_MAX_ZONEORDER=14
CONFIG_GENERIC_CALIBRATE_DELAY=y
#
# Memory Setup
#
-CONFIG_MEM_SIZE=64
+CONFIG_MAX_MEM_SIZE=512
CONFIG_MEM_ADD_WIDTH=9
CONFIG_BOOT_LOAD=0x1000
CONFIG_BFIN_SCRATCH_REG_RETN=y
--- /dev/null
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.22.16
+#
+# CONFIG_MMU is not set
+# CONFIG_FPU is not set
+CONFIG_RWSEM_GENERIC_SPINLOCK=y
+# CONFIG_RWSEM_XCHGADD_ALGORITHM is not set
+CONFIG_BLACKFIN=y
+CONFIG_ZONE_DMA=y
+CONFIG_SEMAPHORE_SLEEPERS=y
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_GPIO=y
+CONFIG_FORCE_MAX_ZONEORDER=14
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+
+#
+# Code maturity level options
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+
+#
+# General setup
+#
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_SYSVIPC=y
+# CONFIG_IPC_NS is not set
+CONFIG_SYSVIPC_SYSCTL=y
+# CONFIG_POSIX_MQUEUE is not set
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_UTS_NS is not set
+# CONFIG_AUDIT is not set
+# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_SYSFS_DEPRECATED=y
+# CONFIG_RELAY is not set
+# CONFIG_BLK_DEV_INITRD is not set
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SYSCTL=y
+CONFIG_EMBEDDED=y
+# CONFIG_UID16 is not set
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+# CONFIG_HOTPLUG is not set
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_ANON_INODES=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_EVENTFD=y
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_BIG_ORDER_ALLOC_NOFAIL_MAGIC=3
+# CONFIG_NP2 is not set
+CONFIG_SLAB=y
+# CONFIG_SLUB is not set
+# CONFIG_SLOB is not set
+CONFIG_RT_MUTEXES=y
+CONFIG_TINY_SHMEM=y
+CONFIG_BASE_SMALL=0
+
+#
+# Loadable module support
+#
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_MODULE_FORCE_UNLOAD is not set
+# CONFIG_MODVERSIONS is not set
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+CONFIG_KMOD=y
+
+#
+# Block layer
+#
+CONFIG_BLOCK=y
+# CONFIG_LBD is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+# CONFIG_IOSCHED_AS is not set
+# CONFIG_IOSCHED_DEADLINE is not set
+CONFIG_IOSCHED_CFQ=y
+# CONFIG_DEFAULT_AS is not set
+# CONFIG_DEFAULT_DEADLINE is not set
+# CONFIG_DEFAULT_CFQ is not set
+CONFIG_DEFAULT_NOOP=y
+CONFIG_DEFAULT_IOSCHED="noop"
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+
+#
+# Blackfin Processor Options
+#
+
+#
+# Processor and Board Settings
+#
+# CONFIG_BF522 is not set
+# CONFIG_BF523 is not set
+# CONFIG_BF524 is not set
+# CONFIG_BF525 is not set
+# CONFIG_BF526 is not set
+# CONFIG_BF527 is not set
+# CONFIG_BF531 is not set
+# CONFIG_BF532 is not set
+CONFIG_BF533=y
+# CONFIG_BF534 is not set
+# CONFIG_BF536 is not set
+# CONFIG_BF537 is not set
+# CONFIG_BF542 is not set
+# CONFIG_BF544 is not set
+# CONFIG_BF547 is not set
+# CONFIG_BF548 is not set
+# CONFIG_BF549 is not set
+# CONFIG_BF561 is not set
+# CONFIG_BF_REV_0_0 is not set
+# CONFIG_BF_REV_0_1 is not set
+# CONFIG_BF_REV_0_2 is not set
+CONFIG_BF_REV_0_3=y
+# CONFIG_BF_REV_0_4 is not set
+# CONFIG_BF_REV_0_5 is not set
+# CONFIG_BF_REV_ANY is not set
+# CONFIG_BF_REV_NONE is not set
+CONFIG_BF53x=y
+CONFIG_BFIN_SINGLE_CORE=y
+CONFIG_MEM_MT48LC16M16A2TG_75=y
+# CONFIG_BFIN533_EZKIT is not set
+# CONFIG_BFIN533_STAMP is not set
+CONFIG_BFIN533_BLUETECHNIX_CM=y
+# CONFIG_H8606_HVSISTEMAS is not set
+# CONFIG_GENERIC_BF533_BOARD is not set
+
+#
+# BF533/2/1 Specific Configuration
+#
+
+#
+# Interrupt Priority Assignment
+#
+
+#
+# Priority
+#
+CONFIG_UART_ERROR=7
+CONFIG_SPORT0_ERROR=7
+CONFIG_SPI_ERROR=7
+CONFIG_SPORT1_ERROR=7
+CONFIG_PPI_ERROR=7
+CONFIG_DMA_ERROR=7
+CONFIG_PLLWAKE_ERROR=7
+CONFIG_RTC_ERROR=8
+CONFIG_DMA0_PPI=8
+CONFIG_DMA1_SPORT0RX=9
+CONFIG_DMA2_SPORT0TX=9
+CONFIG_DMA3_SPORT1RX=9
+CONFIG_DMA4_SPORT1TX=9
+CONFIG_DMA5_SPI=10
+CONFIG_DMA6_UARTRX=10
+CONFIG_DMA7_UARTTX=10
+CONFIG_TIMER0=11
+CONFIG_TIMER1=11
+CONFIG_TIMER2=11
+CONFIG_PFA=12
+CONFIG_PFB=12
+CONFIG_MEMDMA0=13
+CONFIG_MEMDMA1=13
+CONFIG_WDTIMER=13
+
+#
+# Board customizations
+#
+# CONFIG_CMDLINE_BOOL is not set
+
+#
+# Clock/PLL Setup
+#
+CONFIG_CLKIN_HZ=25000000
+# CONFIG_BFIN_KERNEL_CLOCK is not set
+CONFIG_MAX_VCO_HZ=750000000
+CONFIG_MIN_VCO_HZ=50000000
+CONFIG_MAX_SCLK_HZ=133333333
+CONFIG_MIN_SCLK_HZ=27000000
+
+#
+# Kernel Timer/Scheduler
+#
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_250=y
+# CONFIG_HZ_300 is not set
+# CONFIG_HZ_1000 is not set
+CONFIG_HZ=250
+
+#
+# Memory Setup
+#
+CONFIG_MAX_MEM_SIZE=32
+CONFIG_MEM_ADD_WIDTH=9
+CONFIG_BOOT_LOAD=0x1000
+CONFIG_BFIN_SCRATCH_REG_RETN=y
+# CONFIG_BFIN_SCRATCH_REG_RETE is not set
+# CONFIG_BFIN_SCRATCH_REG_CYCLES is not set
+
+#
+# Blackfin Kernel Optimizations
+#
+
+#
+# Memory Optimizations
+#
+CONFIG_I_ENTRY_L1=y
+CONFIG_EXCPT_IRQ_SYSC_L1=y
+CONFIG_DO_IRQ_L1=y
+CONFIG_CORE_TIMER_IRQ_L1=y
+CONFIG_IDLE_L1=y
+CONFIG_SCHEDULE_L1=y
+CONFIG_ARITHMETIC_OPS_L1=y
+CONFIG_ACCESS_OK_L1=y
+CONFIG_MEMSET_L1=y
+CONFIG_MEMCPY_L1=y
+CONFIG_SYS_BFIN_SPINLOCK_L1=y
+CONFIG_IP_CHECKSUM_L1=y
+CONFIG_CACHELINE_ALIGNED_L1=y
+CONFIG_SYSCALL_TAB_L1=y
+CONFIG_CPLB_SWITCH_TAB_L1=y
+CONFIG_RAMKERNEL=y
+# CONFIG_ROMKERNEL is not set
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4
+# CONFIG_RESOURCES_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=1
+CONFIG_LARGE_ALLOCS=y
+# CONFIG_BFIN_GPTIMERS is not set
+CONFIG_BFIN_DMA_5XX=y
+# CONFIG_DMA_UNCACHED_2M is not set
+CONFIG_DMA_UNCACHED_1M=y
+# CONFIG_DMA_UNCACHED_NONE is not set
+
+#
+# Cache Support
+#
+CONFIG_BFIN_ICACHE=y
+CONFIG_BFIN_DCACHE=y
+# CONFIG_BFIN_DCACHE_BANKA is not set
+# CONFIG_BFIN_ICACHE_LOCK is not set
+CONFIG_BFIN_WB=y
+# CONFIG_BFIN_WT is not set
+CONFIG_L1_MAX_PIECE=16
+# CONFIG_MPU is not set
+
+#
+# Asynchonous Memory Configuration
+#
+
+#
+# EBIU_AMGCTL Global Control
+#
+CONFIG_C_AMCKEN=y
+CONFIG_C_CDPRIO=y
+# CONFIG_C_AMBEN is not set
+# CONFIG_C_AMBEN_B0 is not set
+# CONFIG_C_AMBEN_B0_B1 is not set
+# CONFIG_C_AMBEN_B0_B1_B2 is not set
+CONFIG_C_AMBEN_ALL=y
+
+#
+# EBIU_AMBCTL Control
+#
+CONFIG_BANK_0=0x7BB0
+CONFIG_BANK_1=0x7BB0
+CONFIG_BANK_2=0x7BB0
+CONFIG_BANK_3=0xFFC3
+
+#
+# Bus options (PCI, PCMCIA, EISA, MCA, ISA)
+#
+# CONFIG_PCI is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+
+#
+# PCCARD (PCMCIA/CardBus) support
+#
+
+#
+# Executable file formats
+#
+CONFIG_BINFMT_ELF_FDPIC=y
+CONFIG_BINFMT_FLAT=y
+CONFIG_BINFMT_ZFLAT=y
+CONFIG_BINFMT_SHARED_FLAT=y
+# CONFIG_BINFMT_MISC is not set
+
+#
+# Power management options
+#
+# CONFIG_PM is not set
+# CONFIG_PM_WAKEUP_BY_GPIO is not set
+
+#
+# CPU Frequency scaling
+#
+# CONFIG_CPU_FREQ is not set
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+CONFIG_XFRM=y
+# CONFIG_XFRM_USER is not set
+# CONFIG_XFRM_SUB_POLICY is not set
+# CONFIG_XFRM_MIGRATE is not set
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+# CONFIG_IP_MULTICAST is not set
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+# CONFIG_IP_PNP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_ARPD is not set
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+CONFIG_INET_XFRM_MODE_TRANSPORT=y
+CONFIG_INET_XFRM_MODE_TUNNEL=y
+CONFIG_INET_XFRM_MODE_BEET=y
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_INET6_XFRM_TUNNEL is not set
+# CONFIG_INET6_TUNNEL is not set
+# CONFIG_NETLABEL is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+
+#
+# QoS and/or fair queueing
+#
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_MAC80211 is not set
+# CONFIG_IEEE80211 is not set
+# CONFIG_RFKILL is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_SYS_HYPERVISOR is not set
+
+#
+# Connector - unified userspace <-> kernelspace linker
+#
+# CONFIG_CONNECTOR is not set
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_CONCAT is not set
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_REDBOOT_PARTS is not set
+# CONFIG_MTD_CMDLINE_PARTS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_FTL is not set
+# CONFIG_NFTL is not set
+# CONFIG_INFTL is not set
+# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+# CONFIG_MTD_CFI is not set
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+CONFIG_MTD_RAM=y
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+CONFIG_MTD_UCLINUX=y
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+# CONFIG_MTD_NAND is not set
+# CONFIG_MTD_ONENAND is not set
+
+#
+# UBI - Unsorted block images
+#
+# CONFIG_MTD_UBI is not set
+
+#
+# Parallel port support
+#
+# CONFIG_PARPORT is not set
+
+#
+# Plug and Play support
+#
+# CONFIG_PNPACPI is not set
+
+#
+# Block devices
+#
+# CONFIG_BLK_DEV_COW_COMMON is not set
+# CONFIG_BLK_DEV_LOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=4096
+CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+
+#
+# Misc devices
+#
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+# CONFIG_SCSI is not set
+# CONFIG_SCSI_NETLINK is not set
+# CONFIG_ATA is not set
+
+#
+# Multi-device support (RAID and LVM)
+#
+# CONFIG_MD is not set
+
+#
+# Network device support
+#
+CONFIG_NETDEVICES=y
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+# CONFIG_PHYLIB is not set
+
+#
+# Ethernet (10 or 100Mbit)
+#
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+CONFIG_SMC91X=y
+# CONFIG_SMSC911X is not set
+# CONFIG_DM9000 is not set
+CONFIG_NETDEV_1000=y
+# CONFIG_AX88180 is not set
+CONFIG_NETDEV_10000=y
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+# CONFIG_WAN is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_SHAPER is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+
+#
+# ISDN subsystem
+#
+# CONFIG_ISDN is not set
+
+#
+# Telephony Support
+#
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+# CONFIG_INPUT is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+# CONFIG_AD9960 is not set
+# CONFIG_SPI_ADC_BF533 is not set
+# CONFIG_BF5xx_PFLAGS is not set
+# CONFIG_BF5xx_PPIFCD is not set
+# CONFIG_BFIN_SIMPLE_TIMER is not set
+# CONFIG_BF5xx_PPI is not set
+CONFIG_BFIN_SPORT=y
+# CONFIG_BFIN_TIMER_LATENCY is not set
+# CONFIG_VT is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+# CONFIG_SERIAL_8250 is not set
+
+#
+# Non-8250 serial port support
+#
+CONFIG_SERIAL_BFIN=y
+CONFIG_SERIAL_BFIN_CONSOLE=y
+CONFIG_SERIAL_BFIN_DMA=y
+# CONFIG_SERIAL_BFIN_PIO is not set
+CONFIG_SERIAL_BFIN_UART0=y
+# CONFIG_BFIN_UART0_CTSRTS is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+# CONFIG_SERIAL_BFIN_SPORT is not set
+CONFIG_UNIX98_PTYS=y
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+
+#
+# CAN, the car bus and industrial fieldbus
+#
+# CONFIG_CAN4LINUX is not set
+
+#
+# IPMI
+#
+# CONFIG_IPMI_HANDLER is not set
+# CONFIG_WATCHDOG is not set
+# CONFIG_HW_RANDOM is not set
+# CONFIG_GEN_RTC is not set
+# CONFIG_R3964 is not set
+# CONFIG_RAW_DRIVER is not set
+
+#
+# TPM devices
+#
+# CONFIG_TCG_TPM is not set
+# CONFIG_I2C is not set
+
+#
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+
+#
+# Dallas's 1-wire bus
+#
+# CONFIG_W1 is not set
+CONFIG_HWMON=y
+# CONFIG_HWMON_VID is not set
+# CONFIG_SENSORS_ABITUGURU is not set
+# CONFIG_SENSORS_F71805F is not set
+# CONFIG_SENSORS_PC87427 is not set
+# CONFIG_SENSORS_SMSC47M1 is not set
+# CONFIG_SENSORS_SMSC47B397 is not set
+# CONFIG_SENSORS_VT1211 is not set
+# CONFIG_SENSORS_W83627HF is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_SM501 is not set
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+# CONFIG_DVB_CORE is not set
+CONFIG_DAB=y
+
+#
+# Graphics support
+#
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
+# CONFIG_VGASTATE is not set
+# CONFIG_FB is not set
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+
+#
+# USB support
+#
+CONFIG_USB_ARCH_HAS_HCD=y
+# CONFIG_USB_ARCH_HAS_OHCI is not set
+# CONFIG_USB_ARCH_HAS_EHCI is not set
+# CONFIG_USB is not set
+
+#
+# Enable Host or Gadget support to see Inventra options
+#
+
+#
+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+#
+
+#
+# USB Gadget Support
+#
+# CONFIG_USB_GADGET is not set
+# CONFIG_MMC is not set
+
+#
+# LED devices
+#
+# CONFIG_NEW_LEDS is not set
+
+#
+# LED drivers
+#
+
+#
+# LED Triggers
+#
+
+#
+# InfiniBand support
+#
+
+#
+# EDAC - error detection and reporting (RAS) (EXPERIMENTAL)
+#
+
+#
+# Real Time Clock
+#
+# CONFIG_RTC_CLASS is not set
+
+#
+# DMA Engine support
+#
+# CONFIG_DMA_ENGINE is not set
+
+#
+# DMA Clients
+#
+
+#
+# DMA Devices
+#
+
+#
+# PBX support
+#
+# CONFIG_PBX is not set
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+CONFIG_EXT2_FS_XATTR=y
+# CONFIG_EXT2_FS_POSIX_ACL is not set
+# CONFIG_EXT2_FS_SECURITY is not set
+# CONFIG_EXT3_FS is not set
+# CONFIG_EXT4DEV_FS is not set
+CONFIG_FS_MBCACHE=y
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
+# CONFIG_QUOTA is not set
+CONFIG_DNOTIFY=y
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+#&
git.samba.org / sfrench / cifs-2.6.git / commitdiff