* OMAP OCP2SCP - ocp interface to scp interface
properties:
-- compatible : Should be "ti,omap-ocp2scp"
+- compatible : Should be "ti,am437x-ocp2scp" for AM437x processor
+ Should be "ti,omap-ocp2scp" for all others
- reg : Address and length of the register set for the device
- #address-cells, #size-cells : Must be present if the device has sub-nodes
- ranges : the child address space are mapped 1:1 onto the parent address space
T: git git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap.git
S: Maintained
F: arch/arm/*omap*/
+F: arch/arm/configs/omap1_defconfig
+F: arch/arm/configs/omap2plus_defconfig
F: drivers/i2c/busses/i2c-omap.c
F: drivers/irqchip/irq-omap-intc.c
F: drivers/mfd/*omap*.c
};
ocp2scp0: ocp2scp@483a8000 {
- compatible = "ti,omap-ocp2scp";
+ compatible = "ti,am437x-ocp2scp", "ti,omap-ocp2scp";
#address-cells = <1>;
#size-cells = <1>;
ranges;
};
ocp2scp1: ocp2scp@483e8000 {
- compatible = "ti,omap-ocp2scp";
+ compatible = "ti,am437x-ocp2scp", "ti,omap-ocp2scp";
#address-cells = <1>;
#size-cells = <1>;
ranges;
gpios = <&tps659038_gpio 1 GPIO_ACTIVE_HIGH>;
gpio-fan,speed-map = <0 0>,
<13000 1>;
+ #cooling-cells = <2>;
};
extcon_usb1: extcon_usb1 {
pinctrl-0 = <&tmp102_pins_default>;
interrupt-parent = <&gpio7>;
interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
+ #thermal-sensor-cells = <1>;
};
};
&usb2 {
dr_mode = "peripheral";
};
+
+&cpu_trips {
+ cpu_alert1: cpu_alert1 {
+ temperature = <50000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "active";
+ };
+};
+
+&cpu_cooling_maps {
+ map1 {
+ trip = <&cpu_alert1>;
+ cooling-device = <&gpio_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+};
+
+&thermal_zones {
+ board_thermal: board_thermal {
+ polling-delay-passive = <1250>; /* milliseconds */
+ polling-delay = <1500>; /* milliseconds */
+
+ /* sensor ID */
+ thermal-sensors = <&tmp102 0>;
+
+ board_trips: trips {
+ board_alert0: board_alert {
+ temperature = <40000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "active";
+ };
+
+ board_crit: board_crit {
+ temperature = <105000>; /* millicelsius */
+ hysteresis = <0>; /* millicelsius */
+ type = "critical";
+ };
+ };
+
+ board_cooling_maps: cooling-maps {
+ map0 {
+ trip = <&board_alert0>;
+ cooling-device =
+ <&gpio_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+};
macb1: ethernet@f802c000 {
phy-mode = "rmii";
+ #address-cells = <1>;
+ #size-cells = <0>;
status = "okay";
+
+ ethernet-phy@1 {
+ reg = <0x1>;
+ };
};
dbgu: serial@ffffee00 {
};
};
+ bandgap: bandgap@4a0021e0 {
+ reg = <0x4a0021e0 0xc
+ 0x4a00232c 0xc
+ 0x4a002380 0x2c
+ 0x4a0023C0 0x3c
+ 0x4a002564 0x8
+ 0x4a002574 0x50>;
+ compatible = "ti,dra752-bandgap";
+ interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
+ #thermal-sensor-cells = <1>;
+ };
+
cm_core_aon: cm_core_aon@4a005000 {
compatible = "ti,dra7-cm-core-aon";
reg = <0x4a005000 0x2000>;
status = "disabled";
};
};
+
+ thermal_zones: thermal-zones {
+ #include "omap4-cpu-thermal.dtsi"
+ #include "omap5-gpu-thermal.dtsi"
+ #include "omap5-core-thermal.dtsi"
+ };
+
+};
+
+&cpu_thermal {
+ polling-delay = <500>; /* milliseconds */
};
/include/ "dra7xx-clocks.dtsi"
device_type = "cpu";
compatible = "arm,cortex-a15";
reg = <0>;
+
+ /* cooling options */
+ cooling-min-level = <0>;
+ cooling-max-level = <2>;
+ #cooling-cells = <2>; /* min followed by max */
};
};
clock-names = "cpu";
clock-latency = <300000>; /* From omap-cpufreq driver */
+
+ /* cooling options */
+ cooling-min-level = <0>;
+ cooling-max-level = <2>;
+ #cooling-cells = <2>; /* min followed by max */
};
cpu@1 {
device_type = "cpu";
&mmc_0 {
status = "okay";
num-slots = <1>;
- supports-highspeed;
broken-cd;
card-detect-delay = <200>;
samsung,dw-mshc-ciu-div = <3>;
samsung,dw-mshc-ddr-timing = <1 2>;
pinctrl-names = "default";
pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_cd &sd0_bus4 &sd0_bus8>;
-
- slot@0 {
- reg = <0>;
- bus-width = <8>;
- };
+ bus-width = <8>;
+ cap-mmc-highspeed;
};
/*
&mmc_1 {
status = "okay";
num-slots = <1>;
- supports-highspeed;
broken-cd;
card-detect-delay = <200>;
samsung,dw-mshc-ciu-div = <3>;
samsung,dw-mshc-ddr-timing = <1 2>;
pinctrl-names = "default";
pinctrl-0 = <&sd1_clk &sd1_cmd &sd1_cd &sd1_bus4>;
-
- slot@0 {
- reg = <0>;
- bus-width = <4>;
- };
+ bus-width = <4>;
+ cap-sd-highspeed;
};
&pinctrl_0 {
power_key_irq: power-key-irq {
samsung,pins = "gpx1-3";
- samsung,pin-function = <0>;
+ samsung,pin-function = <0xf>;
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
};
lid_irq: lid-irq {
samsung,pins = "gpx3-5";
- samsung,pin-function = <0>;
+ samsung,pin-function = <0xf>;
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
};
/* sensor ID */
thermal-sensors = <&bandgap 0>;
- trips {
+ cpu_trips: trips {
cpu_alert0: cpu_alert {
temperature = <100000>; /* millicelsius */
hysteresis = <2000>; /* millicelsius */
};
};
- cooling-maps {
+ cpu_cooling_maps: cooling-maps {
map0 {
trip = <&cpu_alert0>;
cooling-device =
__raw_writel(reg, PM_SOFT_RST_REG);
}
-EXPORT_SYMBOL(cns3xxx_pwr_soft_rst_force);
void cns3xxx_pwr_soft_rst(unsigned int block)
{
if (!IS_ENABLED(CONFIG_SMP))
exynos_sysram_init();
-#ifdef CONFIG_ARM_EXYNOS_CPUIDLE
+#if defined(CONFIG_SMP) && defined(CONFIG_ARM_EXYNOS_CPUIDLE)
if (of_machine_is_compatible("samsung,exynos4210"))
exynos_cpuidle.dev.platform_data = &cpuidle_coupled_exynos_data;
#endif
cpu_pm_exit();
}
+#if defined(CONFIG_SMP) && defined(CONFIG_ARM_EXYNOS_CPUIDLE)
static atomic_t cpu1_wakeup = ATOMIC_INIT(0);
static int exynos_cpu0_enter_aftr(void)
.pre_enter_aftr = exynos_pre_enter_aftr,
.post_enter_aftr = exynos_post_enter_aftr,
};
+#endif /* CONFIG_SMP && CONFIG_ARM_EXYNOS_CPUIDLE */
void __iomem *mpsoc_base;
u32 reg;
+ pr_warn("CPU idle is currently broken on Armada 38x: disabling");
+ return 0;
+
np = of_find_compatible_node(NULL, NULL,
"marvell,armada-380-coherency-fabric");
if (!np)
return 0;
of_node_put(np);
+ /*
+ * Currently the CPU idle support for Armada 38x is broken, as
+ * the CPU hotplug uses some of the CPU idle functions it is
+ * broken too, so let's disable it
+ */
+ if (of_machine_is_compatible("marvell,armada380")) {
+ cpu_hotplug_disable();
+ pr_warn("CPU hotplug support is currently broken on Armada 38x: disabling");
+ }
+
if (of_machine_is_compatible("marvell,armadaxp"))
ret = armada_xp_cpuidle_init();
else if (of_machine_is_compatible("marvell,armada370"))
return ret;
mvebu_v7_pmsu_enable_l2_powerdown_onidle();
- platform_device_register(&mvebu_v7_cpuidle_device);
+ if (mvebu_v7_cpuidle_device.name)
+ platform_device_register(&mvebu_v7_cpuidle_device);
cpu_pm_register_notifier(&mvebu_v7_cpu_pm_notifier);
return 0;
static unsigned int mpui1510_sleep_save[MPUI1510_SLEEP_SAVE_SIZE];
static unsigned int mpui1610_sleep_save[MPUI1610_SLEEP_SAVE_SIZE];
-#ifndef CONFIG_OMAP_32K_TIMER
-
-static unsigned short enable_dyn_sleep = 0;
-
-#else
-
-static unsigned short enable_dyn_sleep = 1;
+static unsigned short enable_dyn_sleep;
static ssize_t idle_show(struct kobject *kobj, struct kobj_attribute *attr,
char *buf)
{
unsigned short value;
if (sscanf(buf, "%hu", &value) != 1 ||
- (value != 0 && value != 1)) {
- printk(KERN_ERR "idle_sleep_store: Invalid value\n");
+ (value != 0 && value != 1) ||
+ (value != 0 && !IS_ENABLED(CONFIG_OMAP_32K_TIMER))) {
+ pr_err("idle_sleep_store: Invalid value\n");
return -EINVAL;
}
enable_dyn_sleep = value;
static struct kobj_attribute sleep_while_idle_attr =
__ATTR(sleep_while_idle, 0644, idle_show, idle_store);
-#endif
static void (*omap_sram_suspend)(unsigned long r0, unsigned long r1) = NULL;
{
extern __u32 arm_idlect1_mask;
__u32 use_idlect1 = arm_idlect1_mask;
- int do_sleep = 0;
local_fiq_disable();
#if defined(CONFIG_OMAP_MPU_TIMER) && !defined(CONFIG_OMAP_DM_TIMER)
-#warning Enable 32kHz OS timer in order to allow sleep states in idle
use_idlect1 = use_idlect1 & ~(1 << 9);
-#else
- if (enable_dyn_sleep)
- do_sleep = 1;
#endif
#ifdef CONFIG_OMAP_DM_TIMER
if (omap_dma_running())
use_idlect1 &= ~(1 << 6);
- /* We should be able to remove the do_sleep variable and multiple
+ /*
+ * We should be able to remove the do_sleep variable and multiple
* tests above as soon as drivers, timer and DMA code have been fixed.
- * Even the sleep block count should become obsolete. */
- if ((use_idlect1 != ~0) || !do_sleep) {
+ * Even the sleep block count should become obsolete.
+ */
+ if ((use_idlect1 != ~0) || !enable_dyn_sleep) {
__u32 saved_idlect1 = omap_readl(ARM_IDLECT1);
if (cpu_is_omap15xx())
static int __init omap_pm_init(void)
{
-
-#ifdef CONFIG_OMAP_32K_TIMER
- int error;
-#endif
+ int error = 0;
if (!cpu_class_is_omap1())
return -ENODEV;
- printk("Power Management for TI OMAP.\n");
+ pr_info("Power Management for TI OMAP.\n");
+
+ if (!IS_ENABLED(CONFIG_OMAP_32K_TIMER))
+ pr_info("OMAP1 PM: sleep states in idle disabled due to no 32KiHz timer\n");
+
+ if (!IS_ENABLED(CONFIG_OMAP_DM_TIMER))
+ pr_info("OMAP1 PM: sleep states in idle disabled due to no DMTIMER support\n");
+
+ if (IS_ENABLED(CONFIG_OMAP_32K_TIMER) &&
+ IS_ENABLED(CONFIG_OMAP_DM_TIMER)) {
+ /* OMAP16xx only */
+ pr_info("OMAP1 PM: sleep states in idle enabled\n");
+ enable_dyn_sleep = 1;
+ }
/*
* We copy the assembler sleep/wakeup routines to SRAM.
omap_pm_init_debugfs();
#endif
-#ifdef CONFIG_OMAP_32K_TIMER
error = sysfs_create_file(power_kobj, &sleep_while_idle_attr.attr);
if (error)
printk(KERN_ERR "sysfs_create_file failed: %d\n", error);
-#endif
if (cpu_is_omap16xx()) {
/* configure LOW_PWR pin */
omap_cfg_reg(T20_1610_LOW_PWR);
}
- return 0;
+ return error;
}
__initcall(omap_pm_init);
select ARM_GIC
select HAVE_ARM_ARCH_TIMER
select IRQ_CROSSBAR
+ select ARM_ERRATA_798181 if SMP
config ARCH_OMAP2PLUS
bool
wish to say no. Selecting yes without understanding what is
going on could result in system crashes;
-config OMAP4_ERRATA_I688
- bool "OMAP4 errata: Async Bridge Corruption"
- depends on (ARCH_OMAP4 || SOC_OMAP5) && !ARCH_MULTIPLATFORM
- select ARCH_HAS_BARRIERS
- help
- If a data is stalled inside asynchronous bridge because of back
- pressure, it may be accepted multiple times, creating pointer
- misalignment that will corrupt next transfers on that data path
- until next reset of the system (No recovery procedure once the
- issue is hit, the path remains consistently broken). Async bridge
- can be found on path between MPU to EMIF and MPU to L3 interconnect.
- This situation can happen only when the idle is initiated by a
- Master Request Disconnection (which is trigged by software when
- executing WFI on CPU).
- The work-around for this errata needs all the initiators connected
- through async bridge must ensure that data path is properly drained
- before issuing WFI. This condition will be met if one Strongly ordered
- access is performed to the target right before executing the WFI.
- In MPU case, L3 T2ASYNC FIFO and DDR T2ASYNC FIFO needs to be drained.
- IO barrier ensure that there is no synchronisation loss on initiators
- operating on both interconnect port simultaneously.
endmenu
endif
void __init omap_reserve(void)
{
omap_secure_ram_reserve_memblock();
- omap_barrier_reserve_memblock();
}
void __init omap5_map_io(void);
void __init ti81xx_map_io(void);
-/* omap_barriers_init() is OMAP4 only */
-void omap_barriers_init(void);
-
/**
* omap_test_timeout - busy-loop, testing a condition
* @cond: condition to test until it evaluates to true
void __init omap4_map_io(void)
{
iotable_init(omap44xx_io_desc, ARRAY_SIZE(omap44xx_io_desc));
- omap_barriers_init();
}
#endif
void __init omap5_map_io(void)
{
iotable_init(omap54xx_io_desc, ARRAY_SIZE(omap54xx_io_desc));
- omap_barriers_init();
}
#endif
/*
struct omap_mux *entry;
#ifdef CONFIG_OMAP_MUX
- if (!superset->muxnames || !superset->muxnames[0]) {
+ if (!superset->muxnames[0]) {
superset++;
continue;
}
extern u32 rx51_secure_update_aux_cr(u32 set_bits, u32 clear_bits);
extern u32 rx51_secure_rng_call(u32 ptr, u32 count, u32 flag);
-#ifdef CONFIG_OMAP4_ERRATA_I688
-extern int omap_barrier_reserve_memblock(void);
-#else
-static inline void omap_barrier_reserve_memblock(void)
-{ }
-#endif
-
#ifdef CONFIG_SOC_HAS_REALTIME_COUNTER
void set_cntfreq(void);
#else
#define IRQ_LOCALTIMER 29
-#ifdef CONFIG_OMAP4_ERRATA_I688
-/* Used to implement memory barrier on DRAM path */
-#define OMAP4_DRAM_BARRIER_VA 0xfe600000
-
-void __iomem *dram_sync, *sram_sync;
-
-static phys_addr_t paddr;
-static u32 size;
-
-void omap_bus_sync(void)
-{
- if (dram_sync && sram_sync) {
- writel_relaxed(readl_relaxed(dram_sync), dram_sync);
- writel_relaxed(readl_relaxed(sram_sync), sram_sync);
- isb();
- }
-}
-EXPORT_SYMBOL(omap_bus_sync);
-
-static int __init omap4_sram_init(void)
-{
- struct device_node *np;
- struct gen_pool *sram_pool;
-
- np = of_find_compatible_node(NULL, NULL, "ti,omap4-mpu");
- if (!np)
- pr_warn("%s:Unable to allocate sram needed to handle errata I688\n",
- __func__);
- sram_pool = of_get_named_gen_pool(np, "sram", 0);
- if (!sram_pool)
- pr_warn("%s:Unable to get sram pool needed to handle errata I688\n",
- __func__);
- else
- sram_sync = (void *)gen_pool_alloc(sram_pool, PAGE_SIZE);
-
- return 0;
-}
-omap_arch_initcall(omap4_sram_init);
-
-/* Steal one page physical memory for barrier implementation */
-int __init omap_barrier_reserve_memblock(void)
-{
-
- size = ALIGN(PAGE_SIZE, SZ_1M);
- paddr = arm_memblock_steal(size, SZ_1M);
-
- return 0;
-}
-
-void __init omap_barriers_init(void)
-{
- struct map_desc dram_io_desc[1];
-
- dram_io_desc[0].virtual = OMAP4_DRAM_BARRIER_VA;
- dram_io_desc[0].pfn = __phys_to_pfn(paddr);
- dram_io_desc[0].length = size;
- dram_io_desc[0].type = MT_MEMORY_RW_SO;
- iotable_init(dram_io_desc, ARRAY_SIZE(dram_io_desc));
- dram_sync = (void __iomem *) dram_io_desc[0].virtual;
-
- pr_info("OMAP4: Map 0x%08llx to 0x%08lx for dram barrier\n",
- (long long) paddr, dram_io_desc[0].virtual);
-
-}
-#else
-void __init omap_barriers_init(void)
-{}
-#endif
-
void gic_dist_disable(void)
{
if (gic_dist_base_addr)
#endif /* defined(CONFIG_SMP) && defined(CONFIG_PM) */
-#ifndef CONFIG_OMAP4_ERRATA_I688
ENTRY(omap_bus_sync)
ret lr
ENDPROC(omap_bus_sync)
-#endif
ENTRY(omap_do_wfi)
stmfd sp!, {lr}
bool "SAMSUNG S3C2412"
select CPU_ARM926T
select S3C2412_COMMON_CLK
- select S3C2412_PM if PM
+ select S3C2412_PM if PM_SLEEP
help
Support for the S3C2412 and S3C2413 SoCs from the S3C24XX line
config CPU_S3C2416
bool "SAMSUNG S3C2416/S3C2450"
select CPU_ARM926T
- select S3C2416_PM if PM
+ select S3C2416_PM if PM_SLEEP
select S3C2443_COMMON_CLK
help
Support for the S3C2416 SoC from the S3C24XX line
bool "SAMSUNG S3C2440"
select CPU_ARM920T
select S3C2410_COMMON_CLK
- select S3C2410_PM if PM
+ select S3C2410_PM if PM_SLEEP
help
Support for S3C2440 Samsung Mobile CPU based systems.
bool "SAMSUNG S3C2442"
select CPU_ARM920T
select S3C2410_COMMON_CLK
- select S3C2410_PM if PM
+ select S3C2410_PM if PM_SLEEP
help
Support for S3C2442 Samsung Mobile CPU based systems.
This is a simple driver that is able to control
the state of built in bluetooth chip on h1940.
-config PM_H1940
- bool
- help
- Internal node for H1940 and related PM
-
config MACH_N30
bool "Acer N30 family"
select S3C_DEV_NAND
config S3C2416_PM
bool
select S3C2412_PM_SLEEP
+ select SAMSUNG_WAKEMASK
help
Internal config node to apply S3C2416 power management
endif # CPU_S3C2443
+config PM_H1940
+ bool
+ help
+ Internal node for H1940 and related PM
+
endmenu # SAMSUNG S3C24XX SoCs Support
endif # ARCH_S3C24XX
# PM
-obj-$(CONFIG_PM) += pm.o irq-pm.o sleep.o
+obj-$(CONFIG_PM) += pm.o
+obj-$(CONFIG_PM_SLEEP) += irq-pm.o sleep.o
# common code
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
+#include <linux/delay.h>
+#include <linux/io.h>
+
+#include "regs-clock.h"
+#include "regs-irq.h"
static inline void s3c_pm_debug_init_uart(void)
{
__raw_writel(0x00, S3C2410_CLKCON); /* turn off clocks over sleep */
}
-static void s3c_pm_show_resume_irqs(int start, unsigned long which,
- unsigned long mask);
+/* s3c2410_pm_show_resume_irqs
+ *
+ * print any IRQs asserted at resume time (ie, we woke from)
+*/
+static inline void s3c_pm_show_resume_irqs(int start, unsigned long which,
+ unsigned long mask)
+{
+ int i;
+
+ which &= ~mask;
+
+ for (i = 0; i <= 31; i++) {
+ if (which & (1L<<i)) {
+ S3C_PMDBG("IRQ %d asserted at resume\n", start+i);
+ }
+ }
+}
static inline void s3c_pm_arch_show_resume_irqs(void)
{
#include "s3c2412-power.h"
+#ifdef CONFIG_PM_SLEEP
extern void s3c2412_sleep_enter(void);
static int s3c2416_cpu_suspend(unsigned long arg)
}
arch_initcall(s3c2416_pm_init);
-
+#endif
static void s3c2416_pm_resume(void)
{
#define PFX "s3c24xx-pm: "
+#ifdef CONFIG_PM_SLEEP
static struct sleep_save core_save[] = {
/* we restore the timings here, with the proviso that the board
* brings the system up in an slower, or equal frequency setting
SAVE_ITEM(S3C2410_BANKCON4),
SAVE_ITEM(S3C2410_BANKCON5),
};
+#endif
/* s3c_pm_check_resume_pin
*
}
}
-
+#ifdef CONFIG_PM_SLEEP
void s3c_pm_restore_core(void)
{
s3c_pm_do_restore_core(core_save, ARRAY_SIZE(core_save));
{
s3c_pm_do_save(core_save, ARRAY_SIZE(core_save));
}
-
+#endif
{
printk("S3C2410: Initialising architecture\n");
-#ifdef CONFIG_PM
+#ifdef CONFIG_PM_SLEEP
register_syscore_ops(&s3c2410_pm_syscore_ops);
register_syscore_ops(&s3c24xx_irq_syscore_ops);
#endif
{
printk("S3C2412: Initialising architecture\n");
-#ifdef CONFIG_PM
+#ifdef CONFIG_PM_SLEEP
register_syscore_ops(&s3c2412_pm_syscore_ops);
register_syscore_ops(&s3c24xx_irq_syscore_ops);
#endif
s3c_adc_setname("s3c2416-adc");
s3c_rtc_setname("s3c2416-rtc");
-#ifdef CONFIG_PM
+#ifdef CONFIG_PM_SLEEP
register_syscore_ops(&s3c2416_pm_syscore_ops);
register_syscore_ops(&s3c24xx_irq_syscore_ops);
register_syscore_ops(&s3c2416_irq_syscore_ops);
/* register suspend/resume handlers */
-#ifdef CONFIG_PM
+#ifdef CONFIG_PM_SLEEP
register_syscore_ops(&s3c2410_pm_syscore_ops);
register_syscore_ops(&s3c24xx_irq_syscore_ops);
-#endif
register_syscore_ops(&s3c244x_pm_syscore_ops);
+#endif
/* register our system device for everything else */
{
printk("S3C2442: Initialising architecture\n");
-#ifdef CONFIG_PM
+#ifdef CONFIG_PM_SLEEP
register_syscore_ops(&s3c2410_pm_syscore_ops);
register_syscore_ops(&s3c24xx_irq_syscore_ops);
-#endif
register_syscore_ops(&s3c244x_pm_syscore_ops);
+#endif
return device_register(&s3c2442_dev);
}
core_initcall(s3c2442_core_init);
-#ifdef CONFIG_PM
+#ifdef CONFIG_PM_SLEEP
static struct sleep_save s3c244x_sleep[] = {
SAVE_ITEM(S3C2440_DSC0),
SAVE_ITEM(S3C2440_DSC1),
{
s3c_pm_do_restore(s3c244x_sleep, ARRAY_SIZE(s3c244x_sleep));
}
-#else
-#define s3c244x_suspend NULL
-#define s3c244x_resume NULL
-#endif
struct syscore_ops s3c244x_pm_syscore_ops = {
.suspend = s3c244x_suspend,
.resume = s3c244x_resume,
};
+#endif
config SMDK6410_WM1190_EV1
bool "Support Wolfson Microelectronics 1190-EV1 PMIC card"
depends on MACH_SMDK6410
+ depends on I2C=y
select MFD_WM8350_I2C
select REGULATOR
select REGULATOR_WM8350
config SMDK6410_WM1192_EV1
bool "Support Wolfson Microelectronics 1192-EV1 PMIC card"
depends on MACH_SMDK6410
+ depends on I2C=y
select MFD_WM831X
select MFD_WM831X_I2C
select REGULATOR
config MACH_WLF_CRAGG_6410
bool "Wolfson Cragganmore 6410"
+ depends on I2C=y
select CPU_S3C6410
- select I2C
select LEDS_GPIO_REGISTER
select S3C64XX_DEV_SPI0
select S3C64XX_SETUP_FB_24BPP
# PM
-obj-$(CONFIG_PM) += pm.o irq-pm.o sleep.o
+obj-$(CONFIG_PM) += pm.o
+obj-$(CONFIG_PM_SLEEP) += irq-pm.o sleep.o
obj-$(CONFIG_CPU_IDLE) += cpuidle.o
# DMA support
};
#ifdef CONFIG_REGULATOR
-static struct regulator_consumer_supply smdk6410_b_pwr_5v_consumers[] __initdata = {
+static struct regulator_consumer_supply smdk6410_b_pwr_5v_consumers[] = {
REGULATOR_SUPPLY("PVDD", "0-001b"),
REGULATOR_SUPPLY("AVDD", "0-001b"),
};
}
#endif
+#ifdef CONFIG_PM_SLEEP
static struct sleep_save core_save[] = {
SAVE_ITEM(S3C64XX_MEM0DRVCON),
SAVE_ITEM(S3C64XX_MEM1DRVCON),
s3c_pm_do_save(misc_save, ARRAY_SIZE(misc_save));
s3c_pm_do_save(core_save, ARRAY_SIZE(core_save));
}
+#endif
/* since both s3c6400 and s3c6410 share the same sleep pm calls, we
* put the per-cpu code in here until any new cpu comes along and changes
/* IRQ masks for IRQs allowed to go to sleep (see irq.c) */
extern unsigned long s3c_irqwake_intallow;
+#ifdef CONFIG_PM_SLEEP
extern unsigned long s3c_irqwake_eintallow;
+#else
+#define s3c_irqwake_eintallow 0
+#endif
/* per-cpu sleep functions */
extern int s3c2410_cpu_suspend(unsigned long);
-#ifdef CONFIG_SAMSUNG_PM
+#ifdef CONFIG_PM_SLEEP
extern int s3c_irq_wake(struct irq_data *data, unsigned int state);
-extern int s3c_irqext_wake(struct irq_data *data, unsigned int state);
extern void s3c_cpu_resume(void);
#else
#define s3c_irq_wake NULL
-#define s3c_irqext_wake NULL
#define s3c_cpu_resume NULL
#endif
+#ifdef CONFIG_SAMSUNG_PM
+extern int s3c_irqext_wake(struct irq_data *data, unsigned int state);
+#else
+#define s3c_irqext_wake NULL
+#endif
+
#ifdef CONFIG_S3C_PM_DEBUG_LED_SMDK
/**
* s3c_pm_debug_smdkled() - Debug PM suspend/resume via SMDK Board LEDs
#include <plat/pm-common.h>
#ifdef CONFIG_SAMSUNG_ATAGS
+#include <plat/pm.h>
#include <mach/pm-core.h>
#else
static inline void s3c_pm_debug_init_uart(void) {}
return 0;
}
-/* s3c2410_pm_show_resume_irqs
- *
- * print any IRQs asserted at resume time (ie, we woke from)
-*/
-static void __maybe_unused s3c_pm_show_resume_irqs(int start,
- unsigned long which,
- unsigned long mask)
-{
- int i;
-
- which &= ~mask;
-
- for (i = 0; i <= 31; i++) {
- if (which & (1L<<i)) {
- S3C_PMDBG("IRQ %d asserted at resume\n", start+i);
- }
- }
-}
-
-
void (*pm_cpu_prep)(void);
int (*pm_cpu_sleep)(unsigned long);
*
*/
+#include <linux/io.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/err.h>
#include <linux/of.h>
#include <linux/of_platform.h>
+#define OCP2SCP_TIMING 0x18
+#define SYNC2_MASK 0xf
+
static int ocp2scp_remove_devices(struct device *dev, void *c)
{
struct platform_device *pdev = to_platform_device(dev);
static int omap_ocp2scp_probe(struct platform_device *pdev)
{
int ret;
+ u32 reg;
+ void __iomem *regs;
+ struct resource *res;
struct device_node *np = pdev->dev.of_node;
if (np) {
}
pm_runtime_enable(&pdev->dev);
+ /*
+ * As per AM572x TRM: http://www.ti.com/lit/ug/spruhz6/spruhz6.pdf
+ * under section 26.3.2.2, table 26-26 OCP2SCP TIMING Caution;
+ * As per OMAP4430 TRM: http://www.ti.com/lit/ug/swpu231ap/swpu231ap.pdf
+ * under section 23.12.6.2.2 , Table 23-1213 OCP2SCP TIMING Caution;
+ * As per OMAP4460 TRM: http://www.ti.com/lit/ug/swpu235ab/swpu235ab.pdf
+ * under section 23.12.6.2.2, Table 23-1213 OCP2SCP TIMING Caution;
+ * As per OMAP543x TRM http://www.ti.com/lit/pdf/swpu249
+ * under section 27.3.2.2, Table 27-27 OCP2SCP TIMING Caution;
+ *
+ * Read path of OCP2SCP is not working properly due to low reset value
+ * of SYNC2 parameter in OCP2SCP. Suggested reset value is 0x6 or more.
+ */
+ if (!of_device_is_compatible(np, "ti,am437x-ocp2scp")) {
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ regs = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(regs))
+ goto err0;
+
+ pm_runtime_get_sync(&pdev->dev);
+ reg = readl_relaxed(regs + OCP2SCP_TIMING);
+ reg &= ~(SYNC2_MASK);
+ reg |= 0x6;
+ writel_relaxed(reg, regs + OCP2SCP_TIMING);
+ pm_runtime_put_sync(&pdev->dev);
+ }
return 0;
#ifdef CONFIG_OF
static const struct of_device_id omap_ocp2scp_id_table[] = {
{ .compatible = "ti,omap-ocp2scp" },
+ { .compatible = "ti,am437x-ocp2scp" },
{}
};
MODULE_DEVICE_TABLE(of, omap_ocp2scp_id_table);
{
int ret;
- if (of_machine_is_compatible("samsung,exynos4210")) {
+ if (IS_ENABLED(CONFIG_SMP) &&
+ of_machine_is_compatible("samsung,exynos4210")) {
exynos_cpuidle_pdata = pdev->dev.platform_data;
ret = cpuidle_register(&exynos_coupled_idle_driver,
$(call cmd,dt_S_dtb)
quiet_cmd_dtc = DTC $@
-cmd_dtc = $(CPP) $(dtc_cpp_flags) -x assembler-with-cpp -o $(dtc-tmp) $< ; \
+cmd_dtc = mkdir -p $(dir ${dtc-tmp}) ; \
+ $(CPP) $(dtc_cpp_flags) -x assembler-with-cpp -o $(dtc-tmp) $< ; \
$(objtree)/scripts/dtc/dtc -O dtb -o $@ -b 0 \
-i $(dir $<) $(DTC_FLAGS) \
-d $(depfile).dtc.tmp $(dtc-tmp) ; \
git.samba.org / sfrench / cifs-2.6.git / commitdiff