Datasheet: Only available via NDA from ServerWorks
* ATI IXP200, IXP300, IXP400, SB600, SB700 and SB800 southbridges
Datasheet: Not publicly available
- * AMD SB900
+ * AMD Hudson-2
Datasheet: Not publicly available
* Standard Microsystems (SMSC) SLC90E66 (Victory66) southbridge
Datasheet: Publicly available at the SMSC website http://www.smsc.com
Generic Thermal Sysfs driver How To
-=========================
+===================================
Written by Sujith Thomas <sujith.thomas@intel.com>, Zhang Rui <rui.zhang@intel.com>
0. Introduction
-The generic thermal sysfs provides a set of interfaces for thermal zone devices (sensors)
-and thermal cooling devices (fan, processor...) to register with the thermal management
-solution and to be a part of it.
+The generic thermal sysfs provides a set of interfaces for thermal zone
+devices (sensors) and thermal cooling devices (fan, processor...) to register
+with the thermal management solution and to be a part of it.
-This how-to focuses on enabling new thermal zone and cooling devices to participate
-in thermal management.
-This solution is platform independent and any type of thermal zone devices and
-cooling devices should be able to make use of the infrastructure.
+This how-to focuses on enabling new thermal zone and cooling devices to
+participate in thermal management.
+This solution is platform independent and any type of thermal zone devices
+and cooling devices should be able to make use of the infrastructure.
-The main task of the thermal sysfs driver is to expose thermal zone attributes as well
-as cooling device attributes to the user space.
-An intelligent thermal management application can make decisions based on inputs
-from thermal zone attributes (the current temperature and trip point temperature)
-and throttle appropriate devices.
+The main task of the thermal sysfs driver is to expose thermal zone attributes
+as well as cooling device attributes to the user space.
+An intelligent thermal management application can make decisions based on
+inputs from thermal zone attributes (the current temperature and trip point
+temperature) and throttle appropriate devices.
[0-*] denotes any positive number starting from 0
[1-*] denotes any positive number starting from 1
1. thermal sysfs driver interface functions
1.1 thermal zone device interface
-1.1.1 struct thermal_zone_device *thermal_zone_device_register(char *name, int trips,
- void *devdata, struct thermal_zone_device_ops *ops)
-
- This interface function adds a new thermal zone device (sensor) to
- /sys/class/thermal folder as thermal_zone[0-*].
- It tries to bind all the thermal cooling devices registered at the same time.
-
- name: the thermal zone name.
- trips: the total number of trip points this thermal zone supports.
- devdata: device private data
- ops: thermal zone device call-backs.
- .bind: bind the thermal zone device with a thermal cooling device.
- .unbind: unbind the thermal zone device with a thermal cooling device.
- .get_temp: get the current temperature of the thermal zone.
- .get_mode: get the current mode (user/kernel) of the thermal zone.
- "kernel" means thermal management is done in kernel.
- "user" will prevent kernel thermal driver actions upon trip points
- so that user applications can take charge of thermal management.
- .set_mode: set the mode (user/kernel) of the thermal zone.
- .get_trip_type: get the type of certain trip point.
- .get_trip_temp: get the temperature above which the certain trip point
- will be fired.
+1.1.1 struct thermal_zone_device *thermal_zone_device_register(char *name,
+ int trips, void *devdata, struct thermal_zone_device_ops *ops)
+
+ This interface function adds a new thermal zone device (sensor) to
+ /sys/class/thermal folder as thermal_zone[0-*]. It tries to bind all the
+ thermal cooling devices registered at the same time.
+
+ name: the thermal zone name.
+ trips: the total number of trip points this thermal zone supports.
+ devdata: device private data
+ ops: thermal zone device call-backs.
+ .bind: bind the thermal zone device with a thermal cooling device.
+ .unbind: unbind the thermal zone device with a thermal cooling device.
+ .get_temp: get the current temperature of the thermal zone.
+ .get_mode: get the current mode (user/kernel) of the thermal zone.
+ - "kernel" means thermal management is done in kernel.
+ - "user" will prevent kernel thermal driver actions upon trip points
+ so that user applications can take charge of thermal management.
+ .set_mode: set the mode (user/kernel) of the thermal zone.
+ .get_trip_type: get the type of certain trip point.
+ .get_trip_temp: get the temperature above which the certain trip point
+ will be fired.
1.1.2 void thermal_zone_device_unregister(struct thermal_zone_device *tz)
- This interface function removes the thermal zone device.
- It deletes the corresponding entry form /sys/class/thermal folder and unbind all
- the thermal cooling devices it uses.
+ This interface function removes the thermal zone device.
+ It deletes the corresponding entry form /sys/class/thermal folder and
+ unbind all the thermal cooling devices it uses.
1.2 thermal cooling device interface
1.2.1 struct thermal_cooling_device *thermal_cooling_device_register(char *name,
- void *devdata, struct thermal_cooling_device_ops *)
-
- This interface function adds a new thermal cooling device (fan/processor/...) to
- /sys/class/thermal/ folder as cooling_device[0-*].
- It tries to bind itself to all the thermal zone devices register at the same time.
- name: the cooling device name.
- devdata: device private data.
- ops: thermal cooling devices call-backs.
- .get_max_state: get the Maximum throttle state of the cooling device.
- .get_cur_state: get the Current throttle state of the cooling device.
- .set_cur_state: set the Current throttle state of the cooling device.
+ void *devdata, struct thermal_cooling_device_ops *)
+
+ This interface function adds a new thermal cooling device (fan/processor/...)
+ to /sys/class/thermal/ folder as cooling_device[0-*]. It tries to bind itself
+ to all the thermal zone devices register at the same time.
+ name: the cooling device name.
+ devdata: device private data.
+ ops: thermal cooling devices call-backs.
+ .get_max_state: get the Maximum throttle state of the cooling device.
+ .get_cur_state: get the Current throttle state of the cooling device.
+ .set_cur_state: set the Current throttle state of the cooling device.
1.2.2 void thermal_cooling_device_unregister(struct thermal_cooling_device *cdev)
- This interface function remove the thermal cooling device.
- It deletes the corresponding entry form /sys/class/thermal folder and unbind
- itself from all the thermal zone devices using it.
+ This interface function remove the thermal cooling device.
+ It deletes the corresponding entry form /sys/class/thermal folder and
+ unbind itself from all the thermal zone devices using it.
1.3 interface for binding a thermal zone device with a thermal cooling device
1.3.1 int thermal_zone_bind_cooling_device(struct thermal_zone_device *tz,
- int trip, struct thermal_cooling_device *cdev);
+ int trip, struct thermal_cooling_device *cdev);
- This interface function bind a thermal cooling device to the certain trip point
- of a thermal zone device.
- This function is usually called in the thermal zone device .bind callback.
- tz: the thermal zone device
- cdev: thermal cooling device
- trip: indicates which trip point the cooling devices is associated with
- in this thermal zone.
+ This interface function bind a thermal cooling device to the certain trip
+ point of a thermal zone device.
+ This function is usually called in the thermal zone device .bind callback.
+ tz: the thermal zone device
+ cdev: thermal cooling device
+ trip: indicates which trip point the cooling devices is associated with
+ in this thermal zone.
1.3.2 int thermal_zone_unbind_cooling_device(struct thermal_zone_device *tz,
- int trip, struct thermal_cooling_device *cdev);
+ int trip, struct thermal_cooling_device *cdev);
- This interface function unbind a thermal cooling device from the certain trip point
- of a thermal zone device.
- This function is usually called in the thermal zone device .unbind callback.
- tz: the thermal zone device
- cdev: thermal cooling device
- trip: indicates which trip point the cooling devices is associated with
- in this thermal zone.
+ This interface function unbind a thermal cooling device from the certain
+ trip point of a thermal zone device. This function is usually called in
+ the thermal zone device .unbind callback.
+ tz: the thermal zone device
+ cdev: thermal cooling device
+ trip: indicates which trip point the cooling devices is associated with
+ in this thermal zone.
2. sysfs attributes structure
Thermal zone device sys I/F, created once it's registered:
/sys/class/thermal/thermal_zone[0-*]:
- |-----type: Type of the thermal zone
- |-----temp: Current temperature
- |-----mode: Working mode of the thermal zone
- |-----trip_point_[0-*]_temp: Trip point temperature
- |-----trip_point_[0-*]_type: Trip point type
+ |---type: Type of the thermal zone
+ |---temp: Current temperature
+ |---mode: Working mode of the thermal zone
+ |---trip_point_[0-*]_temp: Trip point temperature
+ |---trip_point_[0-*]_type: Trip point type
Thermal cooling device sys I/F, created once it's registered:
/sys/class/thermal/cooling_device[0-*]:
- |-----type : Type of the cooling device(processor/fan/...)
- |-----max_state: Maximum cooling state of the cooling device
- |-----cur_state: Current cooling state of the cooling device
+ |---type: Type of the cooling device(processor/fan/...)
+ |---max_state: Maximum cooling state of the cooling device
+ |---cur_state: Current cooling state of the cooling device
-These two dynamic attributes are created/removed in pairs.
-They represent the relationship between a thermal zone and its associated cooling device.
-They are created/removed for each
-thermal_zone_bind_cooling_device/thermal_zone_unbind_cooling_device successful execution.
+Then next two dynamic attributes are created/removed in pairs. They represent
+the relationship between a thermal zone and its associated cooling device.
+They are created/removed for each successful execution of
+thermal_zone_bind_cooling_device/thermal_zone_unbind_cooling_device.
-/sys/class/thermal/thermal_zone[0-*]
- |-----cdev[0-*]: The [0-*]th cooling device in the current thermal zone
- |-----cdev[0-*]_trip_point: Trip point that cdev[0-*] is associated with
+/sys/class/thermal/thermal_zone[0-*]:
+ |---cdev[0-*]: [0-*]th cooling device in current thermal zone
+ |---cdev[0-*]_trip_point: Trip point that cdev[0-*] is associated with
Besides the thermal zone device sysfs I/F and cooling device sysfs I/F,
-the generic thermal driver also creates a hwmon sysfs I/F for each _type_ of
-thermal zone device. E.g. the generic thermal driver registers one hwmon class device
-and build the associated hwmon sysfs I/F for all the registered ACPI thermal zones.
+the generic thermal driver also creates a hwmon sysfs I/F for each _type_
+of thermal zone device. E.g. the generic thermal driver registers one hwmon
+class device and build the associated hwmon sysfs I/F for all the registered
+ACPI thermal zones.
+
/sys/class/hwmon/hwmon[0-*]:
- |-----name: The type of the thermal zone devices.
- |-----temp[1-*]_input: The current temperature of thermal zone [1-*].
- |-----temp[1-*]_critical: The critical trip point of thermal zone [1-*].
+ |---name: The type of the thermal zone devices
+ |---temp[1-*]_input: The current temperature of thermal zone [1-*]
+ |---temp[1-*]_critical: The critical trip point of thermal zone [1-*]
+
Please read Documentation/hwmon/sysfs-interface for additional information.
***************************
* Thermal zone attributes *
***************************
-type Strings which represent the thermal zone type.
- This is given by thermal zone driver as part of registration.
- Eg: "acpitz" indicates it's an ACPI thermal device.
- In order to keep it consistent with hwmon sys attribute,
- this should be a short, lowercase string,
- not containing spaces nor dashes.
- RO
- Required
-
-temp Current temperature as reported by thermal zone (sensor)
- Unit: millidegree Celsius
- RO
- Required
-
-mode One of the predefined values in [kernel, user]
- This file gives information about the algorithm
- that is currently managing the thermal zone.
- It can be either default kernel based algorithm
- or user space application.
- RW
- Optional
- kernel = Thermal management in kernel thermal zone driver.
- user = Preventing kernel thermal zone driver actions upon
- trip points so that user application can take full
- charge of the thermal management.
-
-trip_point_[0-*]_temp The temperature above which trip point will be fired
- Unit: millidegree Celsius
- RO
- Optional
-
-trip_point_[0-*]_type Strings which indicate the type of the trip point
- E.g. it can be one of critical, hot, passive,
- active[0-*] for ACPI thermal zone.
- RO
- Optional
-
-cdev[0-*] Sysfs link to the thermal cooling device node where the sys I/F
- for cooling device throttling control represents.
- RO
- Optional
-
-cdev[0-*]_trip_point The trip point with which cdev[0-*] is associated in this thermal zone
- -1 means the cooling device is not associated with any trip point.
- RO
- Optional
-
-******************************
-* Cooling device attributes *
-******************************
-
-type String which represents the type of device
- eg: For generic ACPI: this should be "Fan",
- "Processor" or "LCD"
- eg. For memory controller device on intel_menlow platform:
- this should be "Memory controller"
- RO
- Required
-
-max_state The maximum permissible cooling state of this cooling device.
- RO
- Required
-
-cur_state The current cooling state of this cooling device.
- the value can any integer numbers between 0 and max_state,
- cur_state == 0 means no cooling
- cur_state == max_state means the maximum cooling.
- RW
- Required
+type
+ Strings which represent the thermal zone type.
+ This is given by thermal zone driver as part of registration.
+ E.g: "acpitz" indicates it's an ACPI thermal device.
+ In order to keep it consistent with hwmon sys attribute; this should
+ be a short, lowercase string, not containing spaces nor dashes.
+ RO, Required
+
+temp
+ Current temperature as reported by thermal zone (sensor).
+ Unit: millidegree Celsius
+ RO, Required
+
+mode
+ One of the predefined values in [kernel, user].
+ This file gives information about the algorithm that is currently
+ managing the thermal zone. It can be either default kernel based
+ algorithm or user space application.
+ kernel = Thermal management in kernel thermal zone driver.
+ user = Preventing kernel thermal zone driver actions upon
+ trip points so that user application can take full
+ charge of the thermal management.
+ RW, Optional
+
+trip_point_[0-*]_temp
+ The temperature above which trip point will be fired.
+ Unit: millidegree Celsius
+ RO, Optional
+
+trip_point_[0-*]_type
+ Strings which indicate the type of the trip point.
+ E.g. it can be one of critical, hot, passive, active[0-*] for ACPI
+ thermal zone.
+ RO, Optional
+
+cdev[0-*]
+ Sysfs link to the thermal cooling device node where the sys I/F
+ for cooling device throttling control represents.
+ RO, Optional
+
+cdev[0-*]_trip_point
+ The trip point with which cdev[0-*] is associated in this thermal
+ zone; -1 means the cooling device is not associated with any trip
+ point.
+ RO, Optional
+
+passive
+ Attribute is only present for zones in which the passive cooling
+ policy is not supported by native thermal driver. Default is zero
+ and can be set to a temperature (in millidegrees) to enable a
+ passive trip point for the zone. Activation is done by polling with
+ an interval of 1 second.
+ Unit: millidegrees Celsius
+ RW, Optional
+
+*****************************
+* Cooling device attributes *
+*****************************
+
+type
+ String which represents the type of device, e.g:
+ - for generic ACPI: should be "Fan", "Processor" or "LCD"
+ - for memory controller device on intel_menlow platform:
+ should be "Memory controller".
+ RO, Required
+
+max_state
+ The maximum permissible cooling state of this cooling device.
+ RO, Required
+
+cur_state
+ The current cooling state of this cooling device.
+ The value can any integer numbers between 0 and max_state:
+ - cur_state == 0 means no cooling
+ - cur_state == max_state means the maximum cooling.
+ RW, Required
3. A simple implementation
-ACPI thermal zone may support multiple trip points like critical/hot/passive/active.
-If an ACPI thermal zone supports critical, passive, active[0] and active[1] at the same time,
-it may register itself as a thermal_zone_device (thermal_zone1) with 4 trip points in all.
-It has one processor and one fan, which are both registered as thermal_cooling_device.
-If the processor is listed in _PSL method, and the fan is listed in _AL0 method,
-the sys I/F structure will be built like this:
+ACPI thermal zone may support multiple trip points like critical, hot,
+passive, active. If an ACPI thermal zone supports critical, passive,
+active[0] and active[1] at the same time, it may register itself as a
+thermal_zone_device (thermal_zone1) with 4 trip points in all.
+It has one processor and one fan, which are both registered as
+thermal_cooling_device.
+
+If the processor is listed in _PSL method, and the fan is listed in _AL0
+method, the sys I/F structure will be built like this:
/sys/class/thermal:
|thermal_zone1:
- |-----type: acpitz
- |-----temp: 37000
- |-----mode: kernel
- |-----trip_point_0_temp: 100000
- |-----trip_point_0_type: critical
- |-----trip_point_1_temp: 80000
- |-----trip_point_1_type: passive
- |-----trip_point_2_temp: 70000
- |-----trip_point_2_type: active0
- |-----trip_point_3_temp: 60000
- |-----trip_point_3_type: active1
- |-----cdev0: --->/sys/class/thermal/cooling_device0
- |-----cdev0_trip_point: 1 /* cdev0 can be used for passive */
- |-----cdev1: --->/sys/class/thermal/cooling_device3
- |-----cdev1_trip_point: 2 /* cdev1 can be used for active[0]*/
+ |---type: acpitz
+ |---temp: 37000
+ |---mode: kernel
+ |---trip_point_0_temp: 100000
+ |---trip_point_0_type: critical
+ |---trip_point_1_temp: 80000
+ |---trip_point_1_type: passive
+ |---trip_point_2_temp: 70000
+ |---trip_point_2_type: active0
+ |---trip_point_3_temp: 60000
+ |---trip_point_3_type: active1
+ |---cdev0: --->/sys/class/thermal/cooling_device0
+ |---cdev0_trip_point: 1 /* cdev0 can be used for passive */
+ |---cdev1: --->/sys/class/thermal/cooling_device3
+ |---cdev1_trip_point: 2 /* cdev1 can be used for active[0]*/
|cooling_device0:
- |-----type: Processor
- |-----max_state: 8
- |-----cur_state: 0
+ |---type: Processor
+ |---max_state: 8
+ |---cur_state: 0
|cooling_device3:
- |-----type: Fan
- |-----max_state: 2
- |-----cur_state: 0
+ |---type: Fan
+ |---max_state: 2
+ |---cur_state: 0
/sys/class/hwmon:
|hwmon0:
- |-----name: acpitz
- |-----temp1_input: 37000
- |-----temp1_crit: 100000
+ |---name: acpitz
+ |---temp1_input: 37000
+ |---temp1_crit: 100000
exit(EXIT_FAILURE);
}
-int checked_open(const char *pathname, int flags)
+static int checked_open(const char *pathname, int flags)
{
int fd = open(pathname, flags);
M: Latchesar Ionkov <lucho@ionkov.net>
L: v9fs-developer@lists.sourceforge.net
W: http://swik.net/v9fs
-T: git git://git.kernel.org/pub/scm/linux/kernel/ericvh/v9fs.git
+T: git git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs.git
S: Maintained
F: Documentation/filesystems/9p.txt
F: fs/9p/
L: acpi4asus-user@lists.sourceforge.net
W: http://acpi4asus.sf.net
S: Maintained
-F: arch/x86/kernel/acpi/boot.c
F: drivers/platform/x86/asus_acpi.c
ASUS ASB100 HARDWARE MONITOR DRIVER
F: drivers/net/tg3.*
BROCADE BFA FC SCSI DRIVER
-P: Jing Huang
-M: huangj@brocade.com
-L: linux-scsi@vger.kernel.org
-S: Supported
-F: drivers/scsi/bfa/
+M: Jing Huang <huangj@brocade.com>
+L: linux-scsi@vger.kernel.org
+S: Supported
+F: drivers/scsi/bfa/
BSG (block layer generic sg v4 driver)
M: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
IPMI SUBSYSTEM
M: Corey Minyard <minyard@acm.org>
-L: openipmi-developer@lists.sourceforge.net
+L: openipmi-developer@lists.sourceforge.net (moderated for non-subscribers)
W: http://openipmi.sourceforge.net/
S: Supported
F: Documentation/IPMI.txt
L: coreteam@netfilter.org
W: http://www.netfilter.org/
W: http://www.iptables.org/
-T: git://git.kernel.org/pub/scm/linux/kernel/git/kaber/nf-2.6.git
+T: git git://git.kernel.org/pub/scm/linux/kernel/git/kaber/nf-2.6.git
S: Supported
F: include/linux/netfilter*
F: include/linux/netfilter/
W: http://www.linuxfoundation.org/en/Net
W: http://patchwork.ozlabs.org/project/netdev/list/
T: git git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6.git
+T: git git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6.git
S: Maintained
F: net/
F: include/net/
SECURITY SUBSYSTEM
M: James Morris <jmorris@namei.org>
L: linux-security-module@vger.kernel.org (suggested Cc:)
-T: git git://www.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6.git
+T: git git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6.git
W: http://security.wiki.kernel.org/
S: Supported
F: security/
F: include/linux/libata.h
SERVER ENGINES 10Gbps iSCSI - BladeEngine 2 DRIVER
-P: Jayamohan Kallickal
-M: jayamohank@serverengines.com
-L: linux-scsi@vger.kernel.org
-W: http://www.serverengines.com
-S: Supported
-F: drivers/scsi/be2iscsi/
+M: Jayamohan Kallickal <jayamohank@serverengines.com>
+L: linux-scsi@vger.kernel.org
+W: http://www.serverengines.com
+S: Supported
+F: drivers/scsi/be2iscsi/
SERVER ENGINES 10Gbps NIC - BladeEngine 2 DRIVER
M: Sathya Perla <sathyap@serverengines.com>
F: include/linux/vlynq.h
VMWARE VMXNET3 ETHERNET DRIVER
-M: Shreyas Bhatewara <sbhatewara@vmware.com>
-M:
VMware, Inc. <pv-drivers@vmware.com>
-L: netdev@vger.kernel.org
-S: Maintained
-F: drivers/net/vmxnet3/
+M: Shreyas Bhatewara <sbhatewara@vmware.com>
+M:
"VMware, Inc." <pv-drivers@vmware.com>
+L: netdev@vger.kernel.org
+S: Maintained
+F: drivers/net/vmxnet3/
VOLTAGE AND CURRENT REGULATOR FRAMEWORK
M: Liam Girdwood <lrg@slimlogic.co.uk>
VERSION = 2
PATCHLEVEL = 6
SUBLEVEL = 32
-EXTRAVERSION = -rc5
+EXTRAVERSION = -rc7
NAME = Man-Eating Seals of Antiquity
# *DOCUMENTATION*
HOSTCC = gcc
HOSTCXX = g++
-HOSTCFLAGS = -Wall -Wstrict-prototypes -O2 -fomit-frame-pointer
+HOSTCFLAGS = -Wall -Wmissing-prototypes -Wstrict-prototypes -O2 -fomit-frame-pointer
HOSTCXXFLAGS = -O2
# Decide whether to build built-in, modular, or both.
const char * prog_name;
-void
+static void
usage (void)
{
fprintf(stderr,
#define F_GETOWN 6 /* for sockets. */
#define F_SETSIG 10 /* for sockets. */
#define F_GETSIG 11 /* for sockets. */
-#define F_SETOWN_EX 12
-#define F_GETOWN_EX 13
/* for posix fcntl() and lockf() */
#define F_RDLCK 1
register struct thread_info *__current_thread_info __asm__("$8");
#define current_thread_info() __current_thread_info
+#endif /* __ASSEMBLY__ */
+
/* Thread information allocation. */
#define THREAD_SIZE_ORDER 1
#define THREAD_SIZE (2*PAGE_SIZE)
-#endif /* __ASSEMBLY__ */
-
#define PREEMPT_ACTIVE 0x40000000
/*
CONFIG_INITRAMFS_SOURCE=""
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SYSCTL=y
-# CONFIG_EMBEDDED is not set
+CONFIG_EMBEDDED=y
CONFIG_UID16=y
CONFIG_SYSCTL_SYSCALL=y
-CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS is not set
# CONFIG_KALLSYMS_ALL is not set
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_HOTPLUG=y
#
# Processor Features
#
-# CONFIG_ARM_THUMB is not set
+CONFIG_ARM_THUMB=y
# CONFIG_CPU_ICACHE_DISABLE is not set
# CONFIG_CPU_DCACHE_DISABLE is not set
CONFIG_CPU_DCACHE_WRITETHROUGH=y
# CONFIG_HIGH_RES_TIMERS is not set
CONFIG_PREEMPT=y
CONFIG_HZ=100
-# CONFIG_AEABI is not set
+CONFIG_AEABI=y
# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
#
# Power management options
#
-# CONFIG_PM is not set
+CONFIG_PM=y
+# CONFIG_SUSPEND is not set
+CONFIG_PM_RUNTIME=y
#
# Networking
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
# CONFIG_INPUT_TSDEV is not set
-# CONFIG_INPUT_EVDEV is not set
+CONFIG_INPUT_EVDEV=y
# CONFIG_INPUT_EVBUG is not set
#
#
# CONFIG_SPI is not set
# CONFIG_SPI_MASTER is not set
+CONFIG_GPIO_SYSFS=y
#
# Dallas's 1-wire bus
CONFIG_LEDS_TRIGGERS=y
CONFIG_LEDS_TRIGGER_TIMER=y
CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
#
# Multimedia devices
#
# Sound
#
-# CONFIG_SOUND is not set
+CONFIG_SOUND=y
+CONFIG_SND=y
+CONFIG_SND_MIXER_OSS=y
+CONFIG_SND_PCM_OSS=y
+CONFIG_SND_SOC=y
+CONFIG_SND_OMAP_SOC=y
+CONFIG_SND_OMAP_SOC_AMS_DELTA=y
#
# HID Devices
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc4
-# Mon May 4 11:58:57 2009
+# Linux kernel version: 2.6.32-rc6
+# Sat Nov 7 20:31:18 2009
#
CONFIG_ARM=y
CONFIG_SYS_SUPPORTS_APM_EMULATION=y
CONFIG_GENERIC_GPIO=y
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_MMU=y
-# CONFIG_NO_IOPORT is not set
CONFIG_GENERIC_HARDIRQS=y
CONFIG_STACKTRACE_SUPPORT=y
CONFIG_HAVE_LATENCYTOP_SUPPORT=y
CONFIG_HARDIRQS_SW_RESEND=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
-# CONFIG_ARCH_HAS_ILOG2_U32 is not set
-# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_VECTORS_BASE=0xffff0000
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=19
# CONFIG_GROUP_SCHED is not set
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_ALL is not set
# CONFIG_KALLSYMS_EXTRA_PASS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
+
+#
+# Kernel Performance Events And Counters
+#
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_PCI_QUIRKS=y
CONFIG_SLUB_DEBUG=y
# CONFIG_SLOB is not set
CONFIG_PROFILING=y
CONFIG_TRACEPOINTS=y
-# CONFIG_MARKERS is not set
CONFIG_OPROFILE=y
CONFIG_HAVE_OPROFILE=y
CONFIG_KPROBES=y
CONFIG_KRETPROBES=y
CONFIG_HAVE_KPROBES=y
CONFIG_HAVE_KRETPROBES=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_GCOV_KERNEL is not set
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_SLABINFO=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
#
# System Type
#
+CONFIG_MMU=y
# CONFIG_ARCH_AAEC2000 is not set
# CONFIG_ARCH_INTEGRATOR is not set
# CONFIG_ARCH_REALVIEW is not set
# CONFIG_ARCH_VERSATILE is not set
# CONFIG_ARCH_AT91 is not set
# CONFIG_ARCH_CLPS711X is not set
+# CONFIG_ARCH_GEMINI is not set
# CONFIG_ARCH_EBSA110 is not set
# CONFIG_ARCH_EP93XX is not set
-# CONFIG_ARCH_GEMINI is not set
# CONFIG_ARCH_FOOTBRIDGE is not set
+# CONFIG_ARCH_MXC is not set
+# CONFIG_ARCH_STMP3XXX is not set
# CONFIG_ARCH_NETX is not set
# CONFIG_ARCH_H720X is not set
-# CONFIG_ARCH_IMX is not set
+# CONFIG_ARCH_NOMADIK is not set
# CONFIG_ARCH_IOP13XX is not set
# CONFIG_ARCH_IOP32X is not set
# CONFIG_ARCH_IOP33X is not set
# CONFIG_ARCH_IXP4XX is not set
# CONFIG_ARCH_L7200 is not set
CONFIG_ARCH_KIRKWOOD=y
-# CONFIG_ARCH_KS8695 is not set
-# CONFIG_ARCH_NS9XXX is not set
# CONFIG_ARCH_LOKI is not set
# CONFIG_ARCH_MV78XX0 is not set
-# CONFIG_ARCH_MXC is not set
# CONFIG_ARCH_ORION5X is not set
+# CONFIG_ARCH_MMP is not set
+# CONFIG_ARCH_KS8695 is not set
+# CONFIG_ARCH_NS9XXX is not set
+# CONFIG_ARCH_W90X900 is not set
# CONFIG_ARCH_PNX4008 is not set
# CONFIG_ARCH_PXA is not set
-# CONFIG_ARCH_MMP is not set
+# CONFIG_ARCH_MSM is not set
# CONFIG_ARCH_RPC is not set
# CONFIG_ARCH_SA1100 is not set
# CONFIG_ARCH_S3C2410 is not set
# CONFIG_ARCH_S3C64XX is not set
+# CONFIG_ARCH_S5PC1XX is not set
# CONFIG_ARCH_SHARK is not set
# CONFIG_ARCH_LH7A40X is not set
+# CONFIG_ARCH_U300 is not set
# CONFIG_ARCH_DAVINCI is not set
# CONFIG_ARCH_OMAP is not set
-# CONFIG_ARCH_MSM is not set
-# CONFIG_ARCH_W90X900 is not set
+# CONFIG_ARCH_BCMRING is not set
#
# Marvell Kirkwood Implementations
CONFIG_MACH_MV88F6281GTW_GE=y
CONFIG_MACH_SHEEVAPLUG=y
CONFIG_MACH_TS219=y
+CONFIG_MACH_OPENRD_BASE=y
CONFIG_PLAT_ORION=y
#
# CONFIG_CPU_FEROCEON_OLD_ID is not set
CONFIG_CPU_32v5=y
CONFIG_CPU_ABRT_EV5T=y
-CONFIG_CPU_PABRT_NOIFAR=y
+CONFIG_CPU_PABRT_LEGACY=y
CONFIG_CPU_CACHE_VIVT=y
CONFIG_CPU_COPY_FEROCEON=y
CONFIG_CPU_TLB_FEROCEON=y
CONFIG_OUTER_CACHE=y
CONFIG_CACHE_FEROCEON_L2=y
# CONFIG_CACHE_FEROCEON_L2_WRITETHROUGH is not set
+CONFIG_ARM_L1_CACHE_SHIFT=5
#
# Bus support
# CONFIG_VMSPLIT_2G is not set
# CONFIG_VMSPLIT_1G is not set
CONFIG_PAGE_OFFSET=0xC0000000
+# CONFIG_PREEMPT_NONE is not set
+# CONFIG_PREEMPT_VOLUNTARY is not set
CONFIG_PREEMPT=y
CONFIG_HZ=100
CONFIG_AEABI=y
# CONFIG_OABI_COMPAT is not set
-CONFIG_ARCH_FLATMEM_HAS_HOLES=y
# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
# CONFIG_HIGHMEM is not set
# CONFIG_PHYS_ADDR_T_64BIT is not set
CONFIG_ZONE_DMA_FLAG=0
CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
CONFIG_ALIGNMENT_TRAP=y
+CONFIG_UACCESS_WITH_MEMCPY=y
#
# Boot options
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
# CONFIG_NET_SCHED is not set
# CONFIG_DCB is not set
# CONFIG_AF_RXRPC is not set
CONFIG_WIRELESS=y
CONFIG_CFG80211=y
+# CONFIG_NL80211_TESTMODE is not set
+# CONFIG_CFG80211_DEVELOPER_WARNINGS is not set
# CONFIG_CFG80211_REG_DEBUG is not set
+CONFIG_CFG80211_DEFAULT_PS=y
+CONFIG_CFG80211_DEFAULT_PS_VALUE=1
+# CONFIG_CFG80211_DEBUGFS is not set
CONFIG_WIRELESS_OLD_REGULATORY=y
CONFIG_WIRELESS_EXT=y
CONFIG_WIRELESS_EXT_SYSFS=y
CONFIG_LIB80211=y
# CONFIG_LIB80211_DEBUG is not set
CONFIG_MAC80211=y
-
-#
-# Rate control algorithm selection
-#
CONFIG_MAC80211_RC_MINSTREL=y
# CONFIG_MAC80211_RC_DEFAULT_PID is not set
CONFIG_MAC80211_RC_DEFAULT_MINSTREL=y
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
# CONFIG_CONNECTOR is not set
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_CONCAT is not set
CONFIG_MTD_PARTITIONS=y
-# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_REDBOOT_PARTS is not set
CONFIG_MTD_CMDLINE_PARTS=y
# CONFIG_MTD_AFS_PARTS is not set
# CONFIG_MTD_DATAFLASH is not set
CONFIG_MTD_M25P80=y
CONFIG_M25PXX_USE_FAST_READ=y
+# CONFIG_MTD_SST25L is not set
# CONFIG_MTD_SLRAM is not set
# CONFIG_MTD_PHRAM is not set
# CONFIG_MTD_MTDRAM is not set
# CONFIG_BLK_DEV_RAM is not set
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
+# CONFIG_MG_DISK is not set
# CONFIG_MISC_DEVICES is not set
CONFIG_HAVE_IDE=y
# CONFIG_IDE is not set
# CONFIG_BLK_DEV_SR_VENDOR is not set
CONFIG_CHR_DEV_SG=m
# CONFIG_CHR_DEV_SCH is not set
-
-#
-# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
-#
# CONFIG_SCSI_MULTI_LUN is not set
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set
# CONFIG_SCSI_SRP_ATTRS is not set
CONFIG_SCSI_LOWLEVEL=y
# CONFIG_ISCSI_TCP is not set
+# CONFIG_SCSI_BNX2_ISCSI is not set
+# CONFIG_BE2ISCSI is not set
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_3W_9XXX is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_SCSI_AIC94XX is not set
+# CONFIG_SCSI_MVSAS is not set
# CONFIG_SCSI_DPT_I2O is not set
# CONFIG_SCSI_ADVANSYS is not set
# CONFIG_SCSI_ARCMSR is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
-# CONFIG_SCSI_MVSAS is not set
# CONFIG_SCSI_STEX is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_IPR is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
+# CONFIG_SCSI_PMCRAID is not set
# CONFIG_SCSI_SRP is not set
+# CONFIG_SCSI_BFA_FC is not set
# CONFIG_SCSI_DH is not set
# CONFIG_SCSI_OSD_INITIATOR is not set
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
+CONFIG_ATA_VERBOSE_ERROR=y
CONFIG_SATA_PMP=y
CONFIG_SATA_AHCI=y
# CONFIG_SATA_SIL24 is not set
# CONFIG_PATA_ALI is not set
# CONFIG_PATA_AMD is not set
# CONFIG_PATA_ARTOP is not set
+# CONFIG_PATA_ATP867X is not set
# CONFIG_PATA_ATIIXP is not set
# CONFIG_PATA_CMD640_PCI is not set
# CONFIG_PATA_CMD64X is not set
# CONFIG_PATA_OPTIDMA is not set
# CONFIG_PATA_PDC_OLD is not set
# CONFIG_PATA_RADISYS is not set
+# CONFIG_PATA_RDC is not set
# CONFIG_PATA_RZ1000 is not set
# CONFIG_PATA_SC1200 is not set
# CONFIG_PATA_SERVERWORKS is not set
#
#
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
#
# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
# CONFIG_I2O is not set
CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_MACVLAN is not set
# CONFIG_SMSC9420 is not set
# CONFIG_SUNDANCE is not set
# CONFIG_TLAN is not set
+# CONFIG_KS8842 is not set
+# CONFIG_KS8851 is not set
+# CONFIG_KS8851_MLL is not set
# CONFIG_VIA_RHINE is not set
# CONFIG_SC92031 is not set
# CONFIG_ATL2 is not set
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
CONFIG_MV643XX_ETH=y
# CONFIG_QLA3XXX is not set
# CONFIG_ATL1 is not set
# CONFIG_JME is not set
# CONFIG_NETDEV_10000 is not set
# CONFIG_TR is not set
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
CONFIG_WLAN_80211=y
CONFIG_LIBERTAS=y
# CONFIG_MAC80211_HWSIM is not set
# CONFIG_MWL8K is not set
# CONFIG_P54_COMMON is not set
-# CONFIG_ATH5K is not set
-# CONFIG_ATH9K is not set
-# CONFIG_AR9170_USB is not set
+# CONFIG_ATH_COMMON is not set
# CONFIG_IPW2100 is not set
# CONFIG_IPW2200 is not set
# CONFIG_IWLWIFI is not set
# CONFIG_ZD1211RW is not set
# CONFIG_RT2X00 is not set
# CONFIG_HERMES is not set
+# CONFIG_WL12XX is not set
+# CONFIG_IWM is not set
#
# Enable WiMAX (Networking options) to see the WiMAX drivers
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
#
# Input device support
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
+# CONFIG_KEYBOARD_ADP5588 is not set
CONFIG_KEYBOARD_ATKBD=y
-# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_QT2160 is not set
# CONFIG_KEYBOARD_LKKBD is not set
-# CONFIG_KEYBOARD_XTKBD is not set
+CONFIG_KEYBOARD_GPIO=y
+# CONFIG_KEYBOARD_MATRIX is not set
+# CONFIG_KEYBOARD_LM8323 is not set
+# CONFIG_KEYBOARD_MAX7359 is not set
# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_OPENCORES is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
-CONFIG_KEYBOARD_GPIO=y
+# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TABLET is not set
CONFIG_DEVPORT=y
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
+# CONFIG_I2C_COMPAT is not set
CONFIG_I2C_CHARDEV=y
CONFIG_I2C_HELPER_AUTO=y
# Miscellaneous I2C Chip support
#
# CONFIG_DS1682 is not set
-# CONFIG_SENSORS_PCF8574 is not set
-# CONFIG_PCF8575 is not set
-# CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
#
# CONFIG_SPI_SPIDEV is not set
# CONFIG_SPI_TLE62X0 is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+CONFIG_GPIOLIB=y
+# CONFIG_DEBUG_GPIO is not set
+CONFIG_GPIO_SYSFS=y
+
+#
+# Memory mapped GPIO expanders:
+#
+
+#
+# I2C GPIO expanders:
+#
+# CONFIG_GPIO_MAX732X is not set
+# CONFIG_GPIO_PCA953X is not set
+# CONFIG_GPIO_PCF857X is not set
+
+#
+# PCI GPIO expanders:
+#
+# CONFIG_GPIO_BT8XX is not set
+# CONFIG_GPIO_LANGWELL is not set
+
+#
+# SPI GPIO expanders:
+#
+# CONFIG_GPIO_MAX7301 is not set
+# CONFIG_GPIO_MCP23S08 is not set
+# CONFIG_GPIO_MC33880 is not set
+
+#
+# AC97 GPIO expanders:
+#
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
#
# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
+# CONFIG_MFD_ASIC3 is not set
+# CONFIG_HTC_EGPIO is not set
# CONFIG_HTC_PASIC3 is not set
+# CONFIG_TPS65010 is not set
# CONFIG_TWL4030_CORE is not set
# CONFIG_MFD_TMIO is not set
+# CONFIG_MFD_TC6393XB is not set
# CONFIG_PMIC_DA903X is not set
# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM831X is not set
# CONFIG_MFD_WM8350_I2C is not set
# CONFIG_MFD_PCF50633 is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-# CONFIG_DAB is not set
+# CONFIG_MFD_MC13783 is not set
+# CONFIG_AB3100_CORE is not set
+# CONFIG_EZX_PCAP is not set
+# CONFIG_REGULATOR is not set
+# CONFIG_MEDIA_SUPPORT is not set
#
# Graphics support
#
+CONFIG_VGA_ARB=y
# CONFIG_DRM is not set
# CONFIG_VGASTATE is not set
# CONFIG_VIDEO_OUTPUT_CONTROL is not set
# CONFIG_SOUND is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
-# CONFIG_HID_DEBUG is not set
# CONFIG_HIDRAW is not set
#
CONFIG_HID_CHERRY=y
CONFIG_HID_CHICONY=y
CONFIG_HID_CYPRESS=y
+CONFIG_HID_DRAGONRISE=y
# CONFIG_DRAGONRISE_FF is not set
CONFIG_HID_EZKEY=y
CONFIG_HID_KYE=y
CONFIG_HID_GYRATION=y
+CONFIG_HID_TWINHAN=y
CONFIG_HID_KENSINGTON=y
CONFIG_HID_LOGITECH=y
# CONFIG_LOGITECH_FF is not set
CONFIG_HID_SAMSUNG=y
CONFIG_HID_SONY=y
CONFIG_HID_SUNPLUS=y
+CONFIG_HID_GREENASIA=y
# CONFIG_GREENASIA_FF is not set
+CONFIG_HID_SMARTJOYPLUS=y
+# CONFIG_SMARTJOYPLUS_FF is not set
CONFIG_HID_TOPSEED=y
+CONFIG_HID_THRUSTMASTER=y
# CONFIG_THRUSTMASTER_FF is not set
+CONFIG_HID_ZEROPLUS=y
# CONFIG_ZEROPLUS_FF is not set
CONFIG_USB_SUPPORT=y
CONFIG_USB_ARCH_HAS_HCD=y
# USB Host Controller Drivers
#
# CONFIG_USB_C67X00_HCD is not set
+# CONFIG_USB_XHCI_HCD is not set
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_EHCI_ROOT_HUB_TT=y
CONFIG_USB_EHCI_TT_NEWSCHED=y
# CONFIG_USB_OXU210HP_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
# CONFIG_USB_ISP1760_HCD is not set
+# CONFIG_USB_ISP1362_HCD is not set
# CONFIG_USB_OHCI_HCD is not set
# CONFIG_USB_UHCI_HCD is not set
# CONFIG_USB_SL811_HCD is not set
# CONFIG_USB_R8A66597_HCD is not set
# CONFIG_USB_WHCI_HCD is not set
# CONFIG_USB_HWA_HCD is not set
+# CONFIG_USB_MUSB_HDRC is not set
#
# USB Device Class drivers
# MMC/SD/SDIO Host Controller Drivers
#
# CONFIG_MMC_SDHCI is not set
+# CONFIG_MMC_AT91 is not set
+# CONFIG_MMC_ATMELMCI is not set
# CONFIG_MMC_TIFM_SD is not set
CONFIG_MMC_MVSDIO=y
# CONFIG_MMC_SPI is not set
+# CONFIG_MMC_CB710 is not set
+# CONFIG_MMC_VIA_SDMMC is not set
# CONFIG_MEMSTICK is not set
-# CONFIG_ACCESSIBILITY is not set
CONFIG_NEW_LEDS=y
CONFIG_LEDS_CLASS=y
# CONFIG_LEDS_PCA9532 is not set
CONFIG_LEDS_GPIO=y
CONFIG_LEDS_GPIO_PLATFORM=y
-# CONFIG_LEDS_LP5521 is not set
+# CONFIG_LEDS_LP3944 is not set
# CONFIG_LEDS_PCA955X is not set
# CONFIG_LEDS_DAC124S085 is not set
# CONFIG_LEDS_BD2802 is not set
CONFIG_LEDS_TRIGGER_TIMER=y
CONFIG_LEDS_TRIGGER_HEARTBEAT=y
# CONFIG_LEDS_TRIGGER_BACKLIGHT is not set
+# CONFIG_LEDS_TRIGGER_GPIO is not set
CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
#
# iptables trigger is under Netfilter config (LED target)
#
+# CONFIG_ACCESSIBILITY is not set
+# CONFIG_INFINIBAND is not set
CONFIG_RTC_LIB=y
CONFIG_RTC_CLASS=y
CONFIG_RTC_HCTOSYS=y
CONFIG_RTC_DRV_S35390A=y
# CONFIG_RTC_DRV_FM3130 is not set
# CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
#
# SPI RTC drivers
# CONFIG_RTC_DRV_R9701 is not set
# CONFIG_RTC_DRV_RS5C348 is not set
# CONFIG_RTC_DRV_DS3234 is not set
+# CONFIG_RTC_DRV_PCF2123 is not set
#
# Platform RTC drivers
# CONFIG_ASYNC_TX_DMA is not set
# CONFIG_DMATEST is not set
# CONFIG_AUXDISPLAY is not set
-# CONFIG_REGULATOR is not set
# CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
# CONFIG_STAGING is not set
#
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
CONFIG_MAGIC_SYSRQ=y
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_OBJECTS is not set
# CONFIG_SLUB_DEBUG_ON is not set
# CONFIG_SLUB_STATS is not set
+# CONFIG_DEBUG_KMEMLEAK is not set
# CONFIG_DEBUG_PREEMPT is not set
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
# CONFIG_DEBUG_LIST is not set
# CONFIG_DEBUG_SG is not set
# CONFIG_DEBUG_NOTIFIERS is not set
+# CONFIG_DEBUG_CREDENTIALS is not set
# CONFIG_BOOT_PRINTK_DELAY is not set
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_RCU_CPU_STALL_DETECTOR is not set
# CONFIG_KPROBES_SANITY_TEST is not set
# CONFIG_BACKTRACE_SELF_TEST is not set
# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
+# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
# CONFIG_LKDTM is not set
# CONFIG_FAULT_INJECTION is not set
# CONFIG_LATENCYTOP is not set
CONFIG_NOP_TRACER=y
CONFIG_HAVE_FUNCTION_TRACER=y
CONFIG_RING_BUFFER=y
+CONFIG_EVENT_TRACING=y
+CONFIG_CONTEXT_SWITCH_TRACER=y
+CONFIG_RING_BUFFER_ALLOW_SWAP=y
CONFIG_TRACING=y
CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
-# CONFIG_FUNCTION_TRACER is not set
-# CONFIG_IRQSOFF_TRACER is not set
-# CONFIG_PREEMPT_TRACER is not set
-# CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
-# CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
-# CONFIG_STACK_TRACER is not set
-# CONFIG_KMEMTRACE is not set
-# CONFIG_WORKQUEUE_TRACER is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
-# CONFIG_FTRACE_STARTUP_TEST is not set
+# CONFIG_FTRACE is not set
# CONFIG_DYNAMIC_DEBUG is not set
# CONFIG_SAMPLES is not set
CONFIG_HAVE_ARCH_KGDB=y
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
CONFIG_CRYPTO_ALGAPI=y
CONFIG_CRYPTO_ALGAPI2=y
CONFIG_CRYPTO_AEAD2=y
#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
CONFIG_CRYPTO_CRC32C=y
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
#
# CONFIG_CRYPTO_ANSI_CPRNG is not set
CONFIG_CRYPTO_HW=y
+CONFIG_CRYPTO_DEV_MV_CESA=y
# CONFIG_CRYPTO_DEV_HIFN_795X is not set
CONFIG_BINARY_PRINTF=y
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
-# CONFIG_KEYBOARD_GPIO is not set
+CONFIG_KEYBOARD_GPIO=y
CONFIG_INPUT_MOUSE=y
# CONFIG_MOUSE_PS2 is not set
# CONFIG_MOUSE_SERIAL is not set
# CONFIG_TOUCHSCREEN_TOUCHWIN is not set
# CONFIG_TOUCHSCREEN_USB_COMPOSITE is not set
# CONFIG_TOUCHSCREEN_TOUCHIT213 is not set
-# CONFIG_INPUT_MISC is not set
+CONFIG_INPUT_MISC=y
+CONFIG_INPUT_TWL4030_PWRBUTTON=y
#
# Hardware I/O ports
#
# CONFIG_VGA_CONSOLE is not set
CONFIG_DUMMY_CONSOLE=y
-# CONFIG_SOUND is not set
+CONFIG_SOUND=y
+CONFIG_SOUND_OSS_CORE=y
+CONFIG_SOUND_OSS_CORE_PRECLAIM=y
+CONFIG_SND=y
+CONFIG_SND_TIMER=y
+CONFIG_SND_PCM=y
+CONFIG_SND_JACK=y
+CONFIG_SND_OSSEMUL=y
+CONFIG_SND_MIXER_OSS=y
+CONFIG_SND_PCM_OSS=y
+CONFIG_SND_PCM_OSS_PLUGINS=y
+CONFIG_SND_SUPPORT_OLD_API=y
+CONFIG_SND_VERBOSE_PROCFS=y
+CONFIG_SND_VERBOSE_PRINTK=y
+CONFIG_SND_DRIVERS=y
+CONFIG_SND_USB=y
+CONFIG_SND_SOC=y
+CONFIG_SND_OMAP_SOC=y
+CONFIG_SND_OMAP_SOC_MCBSP=y
+CONFIG_SND_OMAP_SOC_OMAP3_PANDORA=y
+CONFIG_SND_SOC_I2C_AND_SPI=y
+CONFIG_SND_SOC_TWL4030=y
+
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
# CONFIG_HID_DEBUG is not set
# CONFIG_MMC_SPI is not set
# CONFIG_MEMSTICK is not set
# CONFIG_ACCESSIBILITY is not set
-# CONFIG_NEW_LEDS is not set
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_GPIO_PLATFORM=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
+
CONFIG_RTC_LIB=y
CONFIG_RTC_CLASS=y
CONFIG_RTC_HCTOSYS=y
# on-CPU RTC drivers
#
# CONFIG_DMADEVICES is not set
-# CONFIG_REGULATOR is not set
# CONFIG_UIO is not set
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
+CONFIG_REGULATOR_TWL4030=y
+
#
# File systems
#
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
+
+# added by hand for now
+CONFIG_KEYBOARD_TWL4030=y
+CONFIG_USB_OTG_UTILS=y
+CONFIG_TWL4030_USB=y
+CONFIG_MMC_OMAP_HS=y
+
# on-CPU RTC drivers
#
# CONFIG_DMADEVICES is not set
-# CONFIG_REGULATOR is not set
+CONFIG_REGULATOR=y
+# CONFIG_REGULATOR_DEBUG is not set
+# CONFIG_REGULATOR_FIXED_VOLTAGE is not set
+# CONFIG_REGULATOR_VIRTUAL_CONSUMER is not set
+# CONFIG_REGULATOR_USERSPACE_CONSUMER is not set
+# CONFIG_REGULATOR_BQ24022 is not set
+# CONFIG_REGULATOR_MAX1586 is not set
+CONFIG_REGULATOR_TWL4030=y
# CONFIG_UIO is not set
# CONFIG_STAGING is not set
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.30-rc4
-# Mon May 4 14:07:25 2009
+# Linux kernel version: 2.6.32-rc6
+# Sat Nov 7 20:52:21 2009
#
CONFIG_ARM=y
CONFIG_SYS_SUPPORTS_APM_EMULATION=y
CONFIG_GENERIC_GPIO=y
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_MMU=y
-# CONFIG_NO_IOPORT is not set
CONFIG_GENERIC_HARDIRQS=y
CONFIG_STACKTRACE_SUPPORT=y
CONFIG_HAVE_LATENCYTOP_SUPPORT=y
CONFIG_HARDIRQS_SW_RESEND=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
-# CONFIG_ARCH_HAS_ILOG2_U32 is not set
-# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
CONFIG_VECTORS_BASE=0xffff0000
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+CONFIG_CONSTRUCTORS=y
#
# General setup
#
# RCU Subsystem
#
-CONFIG_CLASSIC_RCU=y
-# CONFIG_TREE_RCU is not set
-# CONFIG_PREEMPT_RCU is not set
+CONFIG_TREE_RCU=y
+# CONFIG_TREE_PREEMPT_RCU is not set
+# CONFIG_RCU_TRACE is not set
+CONFIG_RCU_FANOUT=32
+# CONFIG_RCU_FANOUT_EXACT is not set
# CONFIG_TREE_RCU_TRACE is not set
-# CONFIG_PREEMPT_RCU_TRACE is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=14
# CONFIG_GROUP_SCHED is not set
CONFIG_KALLSYMS=y
CONFIG_KALLSYMS_ALL=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_AIO=y
+
+#
+# Kernel Performance Events And Counters
+#
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_PCI_QUIRKS=y
# CONFIG_SLUB_DEBUG is not set
# CONFIG_SLOB is not set
CONFIG_PROFILING=y
CONFIG_TRACEPOINTS=y
-# CONFIG_MARKERS is not set
CONFIG_OPROFILE=y
CONFIG_HAVE_OPROFILE=y
CONFIG_KPROBES=y
CONFIG_KRETPROBES=y
CONFIG_HAVE_KPROBES=y
CONFIG_HAVE_KRETPROBES=y
+
+#
+# GCOV-based kernel profiling
+#
+# CONFIG_GCOV_KERNEL is not set
# CONFIG_SLOW_WORK is not set
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_RT_MUTEXES=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_BLOCK=y
-# CONFIG_LBD is not set
+CONFIG_LBDAF=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
#
# System Type
#
+CONFIG_MMU=y
# CONFIG_ARCH_AAEC2000 is not set
# CONFIG_ARCH_INTEGRATOR is not set
# CONFIG_ARCH_REALVIEW is not set
# CONFIG_ARCH_VERSATILE is not set
# CONFIG_ARCH_AT91 is not set
# CONFIG_ARCH_CLPS711X is not set
+# CONFIG_ARCH_GEMINI is not set
# CONFIG_ARCH_EBSA110 is not set
# CONFIG_ARCH_EP93XX is not set
-# CONFIG_ARCH_GEMINI is not set
# CONFIG_ARCH_FOOTBRIDGE is not set
+# CONFIG_ARCH_MXC is not set
+# CONFIG_ARCH_STMP3XXX is not set
# CONFIG_ARCH_NETX is not set
# CONFIG_ARCH_H720X is not set
-# CONFIG_ARCH_IMX is not set
+# CONFIG_ARCH_NOMADIK is not set
# CONFIG_ARCH_IOP13XX is not set
# CONFIG_ARCH_IOP32X is not set
# CONFIG_ARCH_IOP33X is not set
# CONFIG_ARCH_IXP4XX is not set
# CONFIG_ARCH_L7200 is not set
# CONFIG_ARCH_KIRKWOOD is not set
-# CONFIG_ARCH_KS8695 is not set
-# CONFIG_ARCH_NS9XXX is not set
# CONFIG_ARCH_LOKI is not set
# CONFIG_ARCH_MV78XX0 is not set
-# CONFIG_ARCH_MXC is not set
CONFIG_ARCH_ORION5X=y
+# CONFIG_ARCH_MMP is not set
+# CONFIG_ARCH_KS8695 is not set
+# CONFIG_ARCH_NS9XXX is not set
+# CONFIG_ARCH_W90X900 is not set
# CONFIG_ARCH_PNX4008 is not set
# CONFIG_ARCH_PXA is not set
-# CONFIG_ARCH_MMP is not set
+# CONFIG_ARCH_MSM is not set
# CONFIG_ARCH_RPC is not set
# CONFIG_ARCH_SA1100 is not set
# CONFIG_ARCH_S3C2410 is not set
# CONFIG_ARCH_S3C64XX is not set
+# CONFIG_ARCH_S5PC1XX is not set
# CONFIG_ARCH_SHARK is not set
# CONFIG_ARCH_LH7A40X is not set
+# CONFIG_ARCH_U300 is not set
# CONFIG_ARCH_DAVINCI is not set
# CONFIG_ARCH_OMAP is not set
-# CONFIG_ARCH_MSM is not set
-# CONFIG_ARCH_W90X900 is not set
+# CONFIG_ARCH_BCMRING is not set
#
# Orion Implementations
CONFIG_MACH_TS78XX=y
CONFIG_MACH_MV2120=y
CONFIG_MACH_EDMINI_V2=y
+CONFIG_MACH_D2NET=y
+CONFIG_MACH_BIGDISK=y
+CONFIG_MACH_NET2BIG=y
CONFIG_MACH_MSS2=y
CONFIG_MACH_WNR854T=y
CONFIG_MACH_RD88F5181L_GE=y
CONFIG_CPU_FEROCEON_OLD_ID=y
CONFIG_CPU_32v5=y
CONFIG_CPU_ABRT_EV5T=y
-CONFIG_CPU_PABRT_NOIFAR=y
+CONFIG_CPU_PABRT_LEGACY=y
CONFIG_CPU_CACHE_VIVT=y
CONFIG_CPU_COPY_FEROCEON=y
CONFIG_CPU_TLB_FEROCEON=y
CONFIG_ARM_THUMB=y
# CONFIG_CPU_ICACHE_DISABLE is not set
# CONFIG_CPU_DCACHE_DISABLE is not set
-# CONFIG_OUTER_CACHE is not set
+CONFIG_ARM_L1_CACHE_SHIFT=5
#
# Bus support
# CONFIG_VMSPLIT_2G is not set
# CONFIG_VMSPLIT_1G is not set
CONFIG_PAGE_OFFSET=0xC0000000
+# CONFIG_PREEMPT_NONE is not set
+# CONFIG_PREEMPT_VOLUNTARY is not set
CONFIG_PREEMPT=y
CONFIG_HZ=100
CONFIG_AEABI=y
CONFIG_OABI_COMPAT=y
-CONFIG_ARCH_FLATMEM_HAS_HOLES=y
# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
# CONFIG_HIGHMEM is not set
# CONFIG_PHYS_ADDR_T_64BIT is not set
CONFIG_ZONE_DMA_FLAG=0
CONFIG_VIRT_TO_BUS=y
-CONFIG_UNEVICTABLE_LRU=y
CONFIG_HAVE_MLOCK=y
CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+# CONFIG_KSM is not set
+CONFIG_DEFAULT_MMAP_MIN_ADDR=4096
CONFIG_LEDS=y
CONFIG_LEDS_CPU=y
CONFIG_ALIGNMENT_TRAP=y
+CONFIG_UACCESS_WITH_MEMCPY=y
#
# Boot options
# CONFIG_PM_DEBUG is not set
# CONFIG_SUSPEND is not set
# CONFIG_APM_EMULATION is not set
+# CONFIG_PM_RUNTIME is not set
CONFIG_ARCH_SUSPEND_POSSIBLE=y
CONFIG_NET=y
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
+# CONFIG_RDS is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_PHONET is not set
+# CONFIG_IEEE802154 is not set
# CONFIG_NET_SCHED is not set
# CONFIG_DCB is not set
# CONFIG_AF_RXRPC is not set
CONFIG_WIRELESS=y
# CONFIG_CFG80211 is not set
+CONFIG_CFG80211_DEFAULT_PS_VALUE=0
# CONFIG_WIRELESS_OLD_REGULATORY is not set
CONFIG_WIRELESS_EXT=y
CONFIG_WIRELESS_EXT_SYSFS=y
# CONFIG_LIB80211 is not set
-# CONFIG_MAC80211 is not set
+
+#
+# CFG80211 needs to be enabled for MAC80211
+#
# CONFIG_WIMAX is not set
# CONFIG_RFKILL is not set
# CONFIG_NET_9P is not set
# Generic Driver Options
#
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_DEVTMPFS is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
# CONFIG_CONNECTOR is not set
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_CONCAT is not set
CONFIG_MTD_PARTITIONS=y
-# CONFIG_MTD_TESTS is not set
# CONFIG_MTD_REDBOOT_PARTS is not set
CONFIG_MTD_CMDLINE_PARTS=y
# CONFIG_MTD_AFS_PARTS is not set
# CONFIG_BLK_DEV_RAM is not set
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
+# CONFIG_MG_DISK is not set
CONFIG_MISC_DEVICES=y
# CONFIG_PHANTOM is not set
# CONFIG_SGI_IOC4 is not set
#
# CONFIG_EEPROM_AT24 is not set
# CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_MAX6875 is not set
# CONFIG_EEPROM_93CX6 is not set
+# CONFIG_CB710_CORE is not set
CONFIG_HAVE_IDE=y
# CONFIG_IDE is not set
# CONFIG_BLK_DEV_SR_VENDOR is not set
CONFIG_CHR_DEV_SG=m
# CONFIG_CHR_DEV_SCH is not set
-
-#
-# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
-#
# CONFIG_SCSI_MULTI_LUN is not set
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set
# CONFIG_SCSI_SRP_ATTRS is not set
CONFIG_SCSI_LOWLEVEL=y
# CONFIG_ISCSI_TCP is not set
+# CONFIG_SCSI_BNX2_ISCSI is not set
+# CONFIG_BE2ISCSI is not set
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_3W_9XXX is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_SCSI_AIC94XX is not set
+# CONFIG_SCSI_MVSAS is not set
# CONFIG_SCSI_DPT_I2O is not set
# CONFIG_SCSI_ADVANSYS is not set
# CONFIG_SCSI_ARCMSR is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
-# CONFIG_SCSI_MVSAS is not set
# CONFIG_SCSI_STEX is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_IPR is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
+# CONFIG_SCSI_PMCRAID is not set
# CONFIG_SCSI_SRP is not set
+# CONFIG_SCSI_BFA_FC is not set
# CONFIG_SCSI_DH is not set
# CONFIG_SCSI_OSD_INITIATOR is not set
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
+CONFIG_ATA_VERBOSE_ERROR=y
CONFIG_SATA_PMP=y
# CONFIG_SATA_AHCI is not set
# CONFIG_SATA_SIL24 is not set
# CONFIG_PATA_ALI is not set
# CONFIG_PATA_AMD is not set
# CONFIG_PATA_ARTOP is not set
+# CONFIG_PATA_ATP867X is not set
# CONFIG_PATA_ATIIXP is not set
# CONFIG_PATA_CMD640_PCI is not set
# CONFIG_PATA_CMD64X is not set
# CONFIG_PATA_OPTIDMA is not set
# CONFIG_PATA_PDC_OLD is not set
# CONFIG_PATA_RADISYS is not set
+# CONFIG_PATA_RDC is not set
# CONFIG_PATA_RZ1000 is not set
# CONFIG_PATA_SC1200 is not set
# CONFIG_PATA_SERVERWORKS is not set
#
#
-# Enable only one of the two stacks, unless you know what you are doing
+# You can enable one or both FireWire driver stacks.
+#
+
+#
+# See the help texts for more information.
#
# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
# CONFIG_I2O is not set
CONFIG_NETDEVICES=y
-CONFIG_COMPAT_NET_DEV_OPS=y
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_MACVLAN is not set
# CONFIG_SMSC9420 is not set
# CONFIG_SUNDANCE is not set
# CONFIG_TLAN is not set
+# CONFIG_KS8842 is not set
+# CONFIG_KS8851_MLL is not set
# CONFIG_VIA_RHINE is not set
# CONFIG_SC92031 is not set
# CONFIG_ATL2 is not set
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
+# CONFIG_CNIC is not set
CONFIG_MV643XX_ETH=y
# CONFIG_QLA3XXX is not set
# CONFIG_ATL1 is not set
# CONFIG_JME is not set
# CONFIG_NETDEV_10000 is not set
# CONFIG_TR is not set
-
-#
-# Wireless LAN
-#
+CONFIG_WLAN=y
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
# CONFIG_ISDN is not set
+# CONFIG_PHONE is not set
#
# Input device support
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
+# CONFIG_KEYBOARD_ADP5588 is not set
# CONFIG_KEYBOARD_ATKBD is not set
-# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_QT2160 is not set
# CONFIG_KEYBOARD_LKKBD is not set
-# CONFIG_KEYBOARD_XTKBD is not set
+CONFIG_KEYBOARD_GPIO=y
+# CONFIG_KEYBOARD_MATRIX is not set
+# CONFIG_KEYBOARD_LM8323 is not set
+# CONFIG_KEYBOARD_MAX7359 is not set
# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_OPENCORES is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
-CONFIG_KEYBOARD_GPIO=y
+# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TABLET is not set
CONFIG_DEVPORT=y
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
+# CONFIG_I2C_COMPAT is not set
CONFIG_I2C_CHARDEV=y
CONFIG_I2C_HELPER_AUTO=y
# Miscellaneous I2C Chip support
#
# CONFIG_DS1682 is not set
-# CONFIG_SENSORS_PCF8574 is not set
-# CONFIG_PCF8575 is not set
-# CONFIG_SENSORS_PCA9539 is not set
-# CONFIG_SENSORS_MAX6875 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set
# CONFIG_SPI is not set
+
+#
+# PPS support
+#
+# CONFIG_PPS is not set
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+CONFIG_GPIOLIB=y
+# CONFIG_DEBUG_GPIO is not set
+CONFIG_GPIO_SYSFS=y
+
+#
+# Memory mapped GPIO expanders:
+#
+
+#
+# I2C GPIO expanders:
+#
+# CONFIG_GPIO_MAX732X is not set
+# CONFIG_GPIO_PCA953X is not set
+# CONFIG_GPIO_PCF857X is not set
+
+#
+# PCI GPIO expanders:
+#
+# CONFIG_GPIO_BT8XX is not set
+# CONFIG_GPIO_LANGWELL is not set
+
+#
+# SPI GPIO expanders:
+#
+
+#
+# AC97 GPIO expanders:
+#
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+
+#
+# Native drivers
+#
# CONFIG_SENSORS_AD7414 is not set
# CONFIG_SENSORS_AD7418 is not set
# CONFIG_SENSORS_ADM1021 is not set
# CONFIG_SENSORS_SMSC47B397 is not set
# CONFIG_SENSORS_ADS7828 is not set
# CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_TMP401 is not set
+# CONFIG_SENSORS_TMP421 is not set
# CONFIG_SENSORS_VIA686A is not set
# CONFIG_SENSORS_VT1211 is not set
# CONFIG_SENSORS_VT8231 is not set
# CONFIG_SENSORS_W83L786NG is not set
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
-# CONFIG_HWMON_DEBUG_CHIP is not set
# CONFIG_THERMAL is not set
-# CONFIG_THERMAL_HWMON is not set
# CONFIG_WATCHDOG is not set
CONFIG_SSB_POSSIBLE=y
#
# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
+# CONFIG_MFD_ASIC3 is not set
+# CONFIG_HTC_EGPIO is not set
# CONFIG_HTC_PASIC3 is not set
+# CONFIG_TPS65010 is not set
# CONFIG_TWL4030_CORE is not set
# CONFIG_MFD_TMIO is not set
+# CONFIG_MFD_TC6393XB is not set
# CONFIG_PMIC_DA903X is not set
# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM831X is not set
# CONFIG_MFD_WM8350_I2C is not set
# CONFIG_MFD_PCF50633 is not set
-
-#
-# Multimedia devices
-#
-
-#
-# Multimedia core support
-#
-# CONFIG_VIDEO_DEV is not set
-# CONFIG_DVB_CORE is not set
-# CONFIG_VIDEO_MEDIA is not set
-
-#
-# Multimedia drivers
-#
-# CONFIG_DAB is not set
+# CONFIG_AB3100_CORE is not set
+# CONFIG_REGULATOR is not set
+# CONFIG_MEDIA_SUPPORT is not set
#
# Graphics support
#
+# CONFIG_VGA_ARB is not set
# CONFIG_DRM is not set
# CONFIG_VGASTATE is not set
# CONFIG_VIDEO_OUTPUT_CONTROL is not set
# CONFIG_SOUND is not set
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
-# CONFIG_HID_DEBUG is not set
# CONFIG_HIDRAW is not set
#
# CONFIG_HID_CHERRY is not set
# CONFIG_HID_CHICONY is not set
# CONFIG_HID_CYPRESS is not set
-# CONFIG_DRAGONRISE_FF is not set
+# CONFIG_HID_DRAGONRISE is not set
# CONFIG_HID_EZKEY is not set
# CONFIG_HID_KYE is not set
# CONFIG_HID_GYRATION is not set
+# CONFIG_HID_TWINHAN is not set
# CONFIG_HID_KENSINGTON is not set
# CONFIG_HID_LOGITECH is not set
# CONFIG_HID_MICROSOFT is not set
# CONFIG_HID_SAMSUNG is not set
# CONFIG_HID_SONY is not set
# CONFIG_HID_SUNPLUS is not set
-# CONFIG_GREENASIA_FF is not set
+# CONFIG_HID_GREENASIA is not set
+# CONFIG_HID_SMARTJOYPLUS is not set
# CONFIG_HID_TOPSEED is not set
-# CONFIG_THRUSTMASTER_FF is not set
-# CONFIG_ZEROPLUS_FF is not set
+# CONFIG_HID_THRUSTMASTER is not set
+# CONFIG_HID_ZEROPLUS is not set
CONFIG_USB_SUPPORT=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
# USB Host Controller Drivers
#
# CONFIG_USB_C67X00_HCD is not set
+# CONFIG_USB_XHCI_HCD is not set
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_EHCI_ROOT_HUB_TT=y
CONFIG_USB_EHCI_TT_NEWSCHED=y
# CONFIG_USB_OXU210HP_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
# CONFIG_USB_ISP1760_HCD is not set
+# CONFIG_USB_ISP1362_HCD is not set
# CONFIG_USB_OHCI_HCD is not set
# CONFIG_USB_UHCI_HCD is not set
# CONFIG_USB_SL811_HCD is not set
# CONFIG_USB_R8A66597_HCD is not set
# CONFIG_USB_WHCI_HCD is not set
# CONFIG_USB_HWA_HCD is not set
+# CONFIG_USB_MUSB_HDRC is not set
#
# USB Device Class drivers
# CONFIG_UWB is not set
# CONFIG_MMC is not set
# CONFIG_MEMSTICK is not set
-# CONFIG_ACCESSIBILITY is not set
CONFIG_NEW_LEDS=y
CONFIG_LEDS_CLASS=y
# CONFIG_LEDS_PCA9532 is not set
CONFIG_LEDS_GPIO=y
CONFIG_LEDS_GPIO_PLATFORM=y
-# CONFIG_LEDS_LP5521 is not set
+# CONFIG_LEDS_LP3944 is not set
# CONFIG_LEDS_PCA955X is not set
# CONFIG_LEDS_BD2802 is not set
CONFIG_LEDS_TRIGGER_TIMER=y
CONFIG_LEDS_TRIGGER_HEARTBEAT=y
# CONFIG_LEDS_TRIGGER_BACKLIGHT is not set
+# CONFIG_LEDS_TRIGGER_GPIO is not set
CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
#
# iptables trigger is under Netfilter config (LED target)
#
+# CONFIG_ACCESSIBILITY is not set
+# CONFIG_INFINIBAND is not set
CONFIG_RTC_LIB=y
CONFIG_RTC_CLASS=y
CONFIG_RTC_HCTOSYS=y
CONFIG_RTC_DRV_S35390A=y
# CONFIG_RTC_DRV_FM3130 is not set
# CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RX8025 is not set
#
# SPI RTC drivers
# CONFIG_ASYNC_TX_DMA is not set
# CONFIG_DMATEST is not set
# CONFIG_AUXDISPLAY is not set
-# CONFIG_REGULATOR is not set
# CONFIG_UIO is not set
+
+#
+# TI VLYNQ
+#
# CONFIG_STAGING is not set
#
# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
# CONFIG_EXT3_FS_XATTR is not set
CONFIG_EXT4_FS=m
-# CONFIG_EXT4DEV_COMPAT is not set
CONFIG_EXT4_FS_XATTR=y
# CONFIG_EXT4_FS_POSIX_ACL is not set
# CONFIG_EXT4_FS_SECURITY is not set
+# CONFIG_EXT4_DEBUG is not set
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
CONFIG_JBD2=m
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
-CONFIG_FILE_LOCKING=y
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_BTRFS_FS is not set
+# CONFIG_NILFS2_FS is not set
+CONFIG_FILE_LOCKING=y
+CONFIG_FSNOTIFY=y
CONFIG_DNOTIFY=y
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-# CONFIG_NILFS2_FS is not set
CONFIG_NETWORK_FILESYSTEMS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
CONFIG_ENABLE_MUST_CHECK=y
CONFIG_FRAME_WARN=1024
CONFIG_MAGIC_SYSRQ=y
+# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_UNUSED_SYMBOLS is not set
CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
CONFIG_SCHEDSTATS=y
# CONFIG_TIMER_STATS is not set
# CONFIG_DEBUG_OBJECTS is not set
+# CONFIG_DEBUG_KMEMLEAK is not set
CONFIG_DEBUG_PREEMPT=y
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_RT_MUTEX_TESTER is not set
# CONFIG_DEBUG_LIST is not set
# CONFIG_DEBUG_SG is not set
# CONFIG_DEBUG_NOTIFIERS is not set
+# CONFIG_DEBUG_CREDENTIALS is not set
CONFIG_FRAME_POINTER=y
# CONFIG_BOOT_PRINTK_DELAY is not set
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_KPROBES_SANITY_TEST is not set
# CONFIG_BACKTRACE_SELF_TEST is not set
# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
+# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
# CONFIG_LKDTM is not set
# CONFIG_FAULT_INJECTION is not set
CONFIG_LATENCYTOP=y
CONFIG_NOP_TRACER=y
CONFIG_HAVE_FUNCTION_TRACER=y
CONFIG_RING_BUFFER=y
+CONFIG_EVENT_TRACING=y
+CONFIG_CONTEXT_SWITCH_TRACER=y
+CONFIG_RING_BUFFER_ALLOW_SWAP=y
CONFIG_TRACING=y
CONFIG_TRACING_SUPPORT=y
-
-#
-# Tracers
-#
-# CONFIG_FUNCTION_TRACER is not set
-# CONFIG_IRQSOFF_TRACER is not set
-# CONFIG_PREEMPT_TRACER is not set
-# CONFIG_SCHED_TRACER is not set
-# CONFIG_CONTEXT_SWITCH_TRACER is not set
-# CONFIG_EVENT_TRACER is not set
-# CONFIG_BOOT_TRACER is not set
-# CONFIG_TRACE_BRANCH_PROFILING is not set
-# CONFIG_STACK_TRACER is not set
-# CONFIG_KMEMTRACE is not set
-# CONFIG_WORKQUEUE_TRACER is not set
-# CONFIG_BLK_DEV_IO_TRACE is not set
-# CONFIG_FTRACE_STARTUP_TEST is not set
+# CONFIG_FTRACE is not set
# CONFIG_DYNAMIC_DEBUG is not set
# CONFIG_SAMPLES is not set
CONFIG_HAVE_ARCH_KGDB=y
#
# Crypto core or helper
#
-# CONFIG_CRYPTO_FIPS is not set
-CONFIG_CRYPTO_ALGAPI=m
-CONFIG_CRYPTO_ALGAPI2=m
-CONFIG_CRYPTO_AEAD2=m
+CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_ALGAPI2=y
+CONFIG_CRYPTO_AEAD2=y
CONFIG_CRYPTO_BLKCIPHER=m
-CONFIG_CRYPTO_BLKCIPHER2=m
-CONFIG_CRYPTO_HASH2=m
-CONFIG_CRYPTO_RNG2=m
-CONFIG_CRYPTO_PCOMP=m
+CONFIG_CRYPTO_BLKCIPHER2=y
+CONFIG_CRYPTO_HASH2=y
+CONFIG_CRYPTO_RNG2=y
+CONFIG_CRYPTO_PCOMP=y
CONFIG_CRYPTO_MANAGER=m
-CONFIG_CRYPTO_MANAGER2=m
+CONFIG_CRYPTO_MANAGER2=y
# CONFIG_CRYPTO_GF128MUL is not set
# CONFIG_CRYPTO_NULL is not set
-CONFIG_CRYPTO_WORKQUEUE=m
+CONFIG_CRYPTO_WORKQUEUE=y
# CONFIG_CRYPTO_CRYPTD is not set
# CONFIG_CRYPTO_AUTHENC is not set
# CONFIG_CRYPTO_TEST is not set
#
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_VMAC is not set
#
# Digest
#
# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_GHASH is not set
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
#
# Ciphers
#
-# CONFIG_CRYPTO_AES is not set
+CONFIG_CRYPTO_AES=y
# CONFIG_CRYPTO_ANUBIS is not set
# CONFIG_CRYPTO_ARC4 is not set
# CONFIG_CRYPTO_BLOWFISH is not set
#
# CONFIG_CRYPTO_ANSI_CPRNG is not set
CONFIG_CRYPTO_HW=y
+CONFIG_CRYPTO_DEV_MV_CESA=y
# CONFIG_CRYPTO_DEV_HIFN_795X is not set
CONFIG_BINARY_PRINTF=y
#define __ARM_NR_usr32 (__ARM_NR_BASE+4)
#define __ARM_NR_set_tls (__ARM_NR_BASE+5)
+/*
+ * *NOTE*: This is a ghost syscall private to the kernel. Only the
+ * __kuser_cmpxchg code in entry-armv.S should be aware of its
+ * existence. Don't ever use this from user code.
+ */
+#ifdef __KERNEL__
+#define __ARM_NR_cmpxchg (__ARM_NR_BASE+0x00fff0)
+#endif
+
/*
* The following syscalls are obsolete and no longer available for EABI.
*/
#include <mach/entry-macro.S>
#include <asm/thread_notify.h>
#include <asm/unwind.h>
+#include <asm/unistd.h>
#include "entry-header.S"
* A special ghost syscall is used for that (see traps.c).
*/
stmfd sp!, {r7, lr}
- mov r7, #0xff00 @ 0xfff0 into r7 for EABI
- orr r7, r7, #0xf0
- swi #0x9ffff0
+ ldr r7, =1f @ it's 20 bits
+ swi __ARM_NR_cmpxchg
ldmfd sp!, {r7, pc}
+1: .word __ARM_NR_cmpxchg
#elif __LINUX_ARM_ARCH__ < 6
bl printhex8
adr r0, str_a2
bl printascii
- adr r3, 3f
+ adr r3, 4f
ldmia r3, {r4, r5, r6} @ get machine desc list
sub r4, r3, r4 @ get offset between virt&phys
add r5, r5, r4 @ convert virt addresses to
u32 scu_ctrl;
scu_ctrl = __raw_readl(scu_base + SCU_CTRL);
+ /* already enabled? */
+ if (scu_ctrl & 1)
+ return;
+
scu_ctrl |= 1;
__raw_writel(scu_ctrl, scu_base + SCU_CTRL);
* __kuser_cmpxchg code in entry-armv.S should be aware of its
* existence. Don't ever use this from user code.
*/
- case 0xfff0:
+ case NR(cmpxchg):
for (;;) {
extern void do_DataAbort(unsigned long addr, unsigned int fsr,
struct pt_regs *regs);
if not implemented, rather than raising SIGILL. This
way the calling program can gracefully determine whether
a feature is supported. */
- if (no <= 0x7ff)
+ if ((no & 0xffff) <= 0x7ff)
return -ENOSYS;
break;
}
help
Select this if you are using the Adeneo Neocore 926 board.
-config MACH_AT91SAM9G20EK_2MMC
- bool "Atmel AT91SAM9G20-EK Evaluation Kit modified for 2 MMC Slots"
- depends on ARCH_AT91SAM9G20
- help
- Select this if you are using an Atmel AT91SAM9G20-EK Evaluation Kit
- Rev A or B modified for 2 MMC Slots.
-
endif
# ----------------------------------------------------------
bool "Atmel AT91SAM9G20-EK Evaluation Kit"
depends on ARCH_AT91SAM9G20
help
- Select this if you are using Atmel's AT91SAM9G20-EK Evaluation Kit.
+ Select this if you are using Atmel's AT91SAM9G20-EK Evaluation Kit
+ that embeds only one SD/MMC slot.
+
+config MACH_AT91SAM9G20EK_2MMC
+ bool "Atmel AT91SAM9G20-EK Evaluation Kit with 2 SD/MMC Slots"
+ depends on ARCH_AT91SAM9G20
+ help
+ Select this if you are using an Atmel AT91SAM9G20-EK Evaluation Kit
+ with 2 SD/MMC Slots. This is the case for AT91SAM9G20-EK rev. C and
+ onwards.
config MACH_CPU9G20
bool "Eukrea CPU9G20 board"
config MTD_NAND_ATMEL_BUSWIDTH_16
bool "Enable 16-bit data bus interface to NAND flash"
- depends on (MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9G10EK || MACH_AT91SAM9263EK || MACH_AT91SAM9G20EK || MACH_AT91SAM9G45EKES || MACH_AT91CAP9ADK)
+ depends on (MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9G10EK || MACH_AT91SAM9263EK || MACH_AT91SAM9G20EK || MACH_AT91SAM9G20EK_2MMC || MACH_AT91SAM9G45EKES || MACH_AT91CAP9ADK)
help
On AT91SAM926x boards both types of NAND flash can be present
(8 and 16 bit data bus width).
* SPI devices.
*/
static struct spi_board_info ek_spi_devices[] = {
-#if !defined(CONFIG_MMC_ATMELMCI)
+#if !(defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_AT91))
{ /* DataFlash chip */
.modalias = "mtd_dataflash",
.chip_select = 1,
* MACB Ethernet device
*/
static struct at91_eth_data __initdata ek_macb_data = {
- .phy_irq_pin = AT91_PIN_PC12,
+ .phy_irq_pin = AT91_PIN_PB0,
.is_rmii = 1,
};
/*
* MCI (SD/MMC)
- * det_pin and wp_pin are not connected
+ * wp_pin is not connected
*/
#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE)
static struct mci_platform_data __initdata ek_mmc_data = {
.slot[0] = {
.bus_width = 4,
- .detect_pin = -ENODEV,
+ .detect_pin = AT91_PIN_PC2,
.wp_pin = -ENODEV,
},
.slot[1] = {
.bus_width = 4,
- .detect_pin = -ENODEV,
+ .detect_pin = AT91_PIN_PC9,
.wp_pin = -ENODEV,
},
};
#else
-static struct amci_platform_data __initdata ek_mmc_data = {
+static struct at91_mmc_data __initdata ek_mmc_data = {
+ .slot_b = 1, /* Only one slot so use slot B */
+ .wire4 = 1,
+ .det_pin = AT91_PIN_PC9,
};
#endif
static struct gpio_led ek_leds[] = {
{ /* "bottom" led, green, userled1 to be defined */
.name = "ds5",
- .gpio = AT91_PIN_PB12,
+ .gpio = AT91_PIN_PB8,
.active_low = 1,
.default_trigger = "none",
},
{ /* "power" led, yellow */
.name = "ds1",
- .gpio = AT91_PIN_PB13,
+ .gpio = AT91_PIN_PB9,
.default_trigger = "heartbeat",
}
};
/* Ethernet */
at91_add_device_eth(&ek_macb_data);
/* MMC */
+#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE)
at91_add_device_mci(0, &ek_mmc_data);
+#else
+ at91_add_device_mmc(0, &ek_mmc_data);
+#endif
/* I2C */
at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
/* LEDs */
#define ARCH_ID_AT91SAM9G20 0x019905a0
#define ARCH_ID_AT91SAM9RL64 0x019b03a0
#define ARCH_ID_AT91SAM9G45 0x819b05a0
+#define ARCH_ID_AT91SAM9G45MRL 0x819b05a2 /* aka 9G45-ES2 & non ES lots */
+#define ARCH_ID_AT91SAM9G45ES 0x819b05a1 /* 9G45-ES (Engineering Sample) */
#define ARCH_ID_AT91CAP9 0x039A03A0
#define ARCH_ID_AT91SAM9XE128 0x329973a0
return (at91_sys_read(AT91_DBGU_CIDR) & ~AT91_CIDR_VERSION);
}
+static inline unsigned long at91_cpu_fully_identify(void)
+{
+ return at91_sys_read(AT91_DBGU_CIDR);
+}
+
#define ARCH_EXID_AT91SAM9M11 0x00000001
#define ARCH_EXID_AT91SAM9M10 0x00000002
#define ARCH_EXID_AT91SAM9G45 0x00000004
#ifdef CONFIG_ARCH_AT91SAM9G45
#define cpu_is_at91sam9g45() (at91_cpu_identify() == ARCH_ID_AT91SAM9G45)
+#define cpu_is_at91sam9g45es() (at91_cpu_fully_identify() == ARCH_ID_AT91SAM9G45ES)
#else
#define cpu_is_at91sam9g45() (0)
+#define cpu_is_at91sam9g45es() (0)
#endif
#ifdef CONFIG_ARCH_AT91CAP9
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/mtd/physmap.h>
+#include <linux/io.h>
#include <mach/hardware.h>
setup_cpu_win(0, KIRKWOOD_PCIE_IO_PHYS_BASE, KIRKWOOD_PCIE_IO_SIZE,
TARGET_PCIE, ATTR_PCIE_IO, KIRKWOOD_PCIE_IO_BUS_BASE);
setup_cpu_win(1, KIRKWOOD_PCIE_MEM_PHYS_BASE, KIRKWOOD_PCIE_MEM_SIZE,
- TARGET_PCIE, ATTR_PCIE_MEM, -1);
+ TARGET_PCIE, ATTR_PCIE_MEM, KIRKWOOD_PCIE_MEM_BUS_BASE);
/*
* Setup window for NAND controller.
return 166666667;
}
-static void kirkwood_timer_init(void)
+static void __init kirkwood_timer_init(void)
{
kirkwood_tclk = kirkwood_find_tclk();
orion_time_init(IRQ_KIRKWOOD_BRIDGE, kirkwood_tclk);
kirkwood_uart0_data[0].uartclk = kirkwood_tclk;
kirkwood_uart1_data[0].uartclk = kirkwood_tclk;
+ /*
+ * Disable propagation of mbus errors to the CPU local bus,
+ * as this causes mbus errors (which can occur for example
+ * for PCI aborts) to throw CPU aborts, which we're not set
+ * up to deal with.
+ */
+ writel(readl(CPU_CONFIG) & ~CPU_CONFIG_ERROR_PROP, CPU_CONFIG);
+
kirkwood_setup_cpu_mbus();
#ifdef CONFIG_CACHE_FEROCEON_L2
#include <mach/kirkwood.h>
+#define CPU_CONFIG (BRIDGE_VIRT_BASE | 0x0100)
+#define CPU_CONFIG_ERROR_PROP 0x00000004
+
#define CPU_CONTROL (BRIDGE_VIRT_BASE | 0x0104)
#define CPU_RESET 0x00000002
static inline void __iomem *__io(unsigned long addr)
{
- return (void __iomem *)((addr - KIRKWOOD_PCIE_IO_PHYS_BASE)
+ return (void __iomem *)((addr - KIRKWOOD_PCIE_IO_BUS_BASE)
+ KIRKWOOD_PCIE_IO_VIRT_BASE);
}
#define KIRKWOOD_REGS_SIZE SZ_1M
#define KIRKWOOD_PCIE_MEM_PHYS_BASE 0xe0000000
+#define KIRKWOOD_PCIE_MEM_BUS_BASE 0xe0000000
#define KIRKWOOD_PCIE_MEM_SIZE SZ_128M
/*
kirkwood_ge00_init(&openrd_base_ge00_data);
kirkwood_sata_init(&openrd_base_sata_data);
kirkwood_sdio_init(&openrd_base_mvsdio_data);
+
+ kirkwood_i2c_init();
}
+static int __init openrd_base_pci_init(void)
+{
+ if (machine_is_openrd_base())
+ kirkwood_pcie_init();
+
+ return 0;
+ }
+subsys_initcall(openrd_base_pci_init);
+
+
MACHINE_START(OPENRD_BASE, "Marvell OpenRD Base Board")
/* Maintainer: Dhaval Vasa <dhaval.vasa@einfochips.com> */
.phys_io = KIRKWOOD_REGS_PHYS_BASE,
};
-static int kirkwood_pcie_setup(int nr, struct pci_sys_data *sys)
+static int __init kirkwood_pcie_setup(int nr, struct pci_sys_data *sys)
{
struct resource *res;
extern unsigned int kirkwood_clk_ctrl;
*/
res[0].name = "PCIe I/O Space";
res[0].flags = IORESOURCE_IO;
- res[0].start = KIRKWOOD_PCIE_IO_PHYS_BASE;
+ res[0].start = KIRKWOOD_PCIE_IO_BUS_BASE;
res[0].end = res[0].start + KIRKWOOD_PCIE_IO_SIZE - 1;
if (request_resource(&ioport_resource, &res[0]))
panic("Request PCIe IO resource failed\n");
*/
res[1].name = "PCIe Memory Space";
res[1].flags = IORESOURCE_MEM;
- res[1].start = KIRKWOOD_PCIE_MEM_PHYS_BASE;
+ res[1].start = KIRKWOOD_PCIE_MEM_BUS_BASE;
res[1].end = res[1].start + KIRKWOOD_PCIE_MEM_SIZE - 1;
if (request_resource(&iomem_resource, &res[1]))
panic("Request PCIe Memory resource failed\n");
#define KS8695_SEC1 (0x04) /* Switch Engine Control 1 */
#define KS8695_SEC2 (0x08) /* Switch Engine Control 2 */
-#define KS8695_P(x)_C(z) (0xc0 + (((x)-1)*3 + ((z)-1))*4) /* Port Configuration Registers */
+#define KS8695_SEPXCZ(x,z) (0x0c + (((x)-1)*3 + ((z)-1))*4) /* Port Configuration Registers */
#define KS8695_SEP12AN (0x48) /* Port 1 & 2 Auto-Negotiation */
#define KS8695_SEP34AN (0x4c) /* Port 3 & 4 Auto-Negotiation */
#define MMC1_WP_MMC1_WP MFP_CFG_DRV(MMC1_WP, AF0, MEDIUM)
/* PWM */
-#define GPIO27 PWM3 AF2 MFP_CFG(GPIO27, AF2)
+#define GPIO27_PWM3_AF2 MFP_CFG(GPIO27, AF2)
#define GPIO51_PWM2_OUT MFP_CFG(GPIO51, AF2)
#define GPIO117_PWM1_OUT MFP_CFG(GPIO117, AF2)
#define GPIO118_PWM2_OUT MFP_CFG(GPIO118, AF2)
} else if (dev == MV78100_DEV_ID) {
if (rev == MV78100_REV_A0)
return "MV78100-A0";
+ else if (rev == MV78100_REV_A1)
+ return "MV78100-A1";
else
return "MV78100-Rev-Unsupported";
} else if (dev == MV78200_DEV_ID) {
#define MV78100_DEV_ID 0x7810
#define MV78100_REV_A0 1
+#define MV78100_REV_A1 2
#define MV78200_DEV_ID 0x7820
#define MV78200_REV_A0 1
/* TWL4030_GPIO_MAX + 0 == ledA, EHCI nEN_USB_PWR (out, active low) */
gpio_request(gpio + TWL4030_GPIO_MAX, "nEN_USB_PWR");
- gpio_direction_output(gpio + TWL4030_GPIO_MAX, 1);
+ gpio_direction_output(gpio + TWL4030_GPIO_MAX, 0);
/* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
}
static int board_keymap[] = {
- /* col, row, code */
+ /* row, col, code */
KEY(0, 0, KEY_9),
- KEY(0, 1, KEY_0),
- KEY(0, 2, KEY_BACKSPACE),
- KEY(0, 3, KEY_O),
- KEY(0, 4, KEY_P),
- KEY(0, 5, KEY_K),
- KEY(0, 6, KEY_L),
- KEY(0, 7, KEY_ENTER),
- KEY(1, 0, KEY_8),
+ KEY(0, 1, KEY_8),
+ KEY(0, 2, KEY_I),
+ KEY(0, 3, KEY_J),
+ KEY(0, 4, KEY_N),
+ KEY(0, 5, KEY_M),
+ KEY(1, 0, KEY_0),
KEY(1, 1, KEY_7),
- KEY(1, 2, KEY_6),
- KEY(1, 3, KEY_5),
- KEY(1, 4, KEY_4),
- KEY(1, 5, KEY_3),
- KEY(1, 6, KEY_2),
- KEY(1, 7, KEY_1),
- KEY(2, 0, KEY_I),
- KEY(2, 1, KEY_U),
+ KEY(1, 2, KEY_U),
+ KEY(1, 3, KEY_H),
+ KEY(1, 4, KEY_B),
+ KEY(1, 5, KEY_SPACE),
+ KEY(2, 0, KEY_BACKSPACE),
+ KEY(2, 1, KEY_6),
KEY(2, 2, KEY_Y),
- KEY(2, 3, KEY_T),
- KEY(2, 4, KEY_R),
- KEY(2, 5, KEY_E),
- KEY(2, 6, KEY_W),
- KEY(2, 7, KEY_Q),
- KEY(3, 0, KEY_J),
- KEY(3, 1, KEY_H),
- KEY(3, 2, KEY_G),
+ KEY(2, 3, KEY_G),
+ KEY(2, 4, KEY_V),
+ KEY(2, 5, KEY_FN),
+ KEY(3, 0, KEY_O),
+ KEY(3, 1, KEY_5),
+ KEY(3, 2, KEY_T),
KEY(3, 3, KEY_F),
- KEY(3, 4, KEY_D),
- KEY(3, 5, KEY_S),
- KEY(3, 6, KEY_A),
- KEY(3, 7, KEY_LEFTSHIFT),
- KEY(4, 0, KEY_N),
- KEY(4, 1, KEY_B),
- KEY(4, 2, KEY_V),
- KEY(4, 3, KEY_C),
+ KEY(3, 4, KEY_C),
+ KEY(4, 0, KEY_P),
+ KEY(4, 1, KEY_4),
+ KEY(4, 2, KEY_R),
+ KEY(4, 3, KEY_D),
KEY(4, 4, KEY_X),
- KEY(4, 5, KEY_Z),
- KEY(4, 6, KEY_DOT),
- KEY(4, 7, KEY_COMMA),
- KEY(5, 0, KEY_M),
- KEY(5, 1, KEY_SPACE),
- KEY(5, 2, KEY_FN),
+ KEY(5, 0, KEY_K),
+ KEY(5, 1, KEY_3),
+ KEY(5, 2, KEY_E),
+ KEY(5, 3, KEY_S),
+ KEY(5, 4, KEY_Z),
+ KEY(6, 0, KEY_L),
+ KEY(6, 1, KEY_2),
+ KEY(6, 2, KEY_W),
+ KEY(6, 3, KEY_A),
+ KEY(6, 4, KEY_DOT),
+ KEY(7, 0, KEY_ENTER),
+ KEY(7, 1, KEY_1),
+ KEY(7, 2, KEY_Q),
+ KEY(7, 3, KEY_LEFTSHIFT),
+ KEY(7, 4, KEY_COMMA),
};
static struct matrix_keymap_data board_map_data = {
if (r < 0)
goto out;
- gpmc_cs_enable_mem(cs, res->start, res->end - res->start + 1);
+ gpmc_cs_enable_mem(cs, res->start, resource_size(res));
*base = res->start;
gpmc_cs_set_reserved(cs, 1);
out:
dev_err(&pdev->dev, "invalid mem resource\n");
return -ENODEV;
}
- mbox_base = ioremap(res->start, res->end - res->start);
+ mbox_base = ioremap(res->start, resource_size(res));
if (!mbox_base)
return -ENOMEM;
#include <mach/colibri.h>
#include <mach/pxafb.h>
#include <mach/ohci.h>
+#include <mach/audio.h>
#include "generic.h"
#include "devices.h"
static inline void colibri_pxa320_init_lcd(void) {}
#endif
-#if defined(SND_AC97_CODEC) || defined(SND_AC97_CODEC_MODULE)
+#if defined(CONFIG_SND_AC97_CODEC) || \
+ defined(CONFIG_SND_AC97_CODEC_MODULE)
static mfp_cfg_t colibri_pxa320_ac97_pin_config[] __initdata = {
GPIO34_AC97_SYSCLK,
GPIO35_AC97_SDATA_IN_0,
static const struct ads7846_platform_data tsc2046_info = {
.model = 7846,
.vref_delay_usecs = 100,
- .pressure_max = 512,
+ .pressure_max = 1024,
.debounce_max = 10,
.debounce_tol = 3,
.debounce_rep = 1,
beq 1001f
bic \irqstat, \irqstat, #0x80000000
mov \irqnr, \irqstat, lsr #16
+ add \irqnr, \irqnr, #(PXA_IRQ(0))
1001:
.endm
#include "generic.h"
+#define MAX_INTERNAL_IRQS 128
+
#define IRQ_BIT(n) (((n) - PXA_IRQ(0)) & 0x1f)
#define _ICMR(n) (*((((n) - PXA_IRQ(0)) & ~0x1f) ? &ICMR2 : &ICMR))
#define _ICLR(n) (*((((n) - PXA_IRQ(0)) & ~0x1f) ? &ICLR2 : &ICLR))
{
int irq, i;
+ BUG_ON(irq_nr > MAX_INTERNAL_IRQS);
+
pxa_internal_irq_nr = irq_nr;
for (irq = PXA_IRQ(0); irq < PXA_IRQ(irq_nr); irq += 32) {
}
#ifdef CONFIG_PM
-static unsigned long saved_icmr[2];
+static unsigned long saved_icmr[MAX_INTERNAL_IRQS/32];
+static unsigned long saved_ipr[MAX_INTERNAL_IRQS];
static int pxa_irq_suspend(struct sys_device *dev, pm_message_t state)
{
saved_icmr[i] = _ICMR(irq);
_ICMR(irq) = 0;
}
+ for (i = 0; i < pxa_internal_irq_nr; i++)
+ saved_ipr[i] = IPR(i);
return 0;
}
_ICMR(irq) = saved_icmr[i];
_ICLR(irq) = 0;
}
+ for (i = 0; i < pxa_internal_irq_nr; i++)
+ IPR(i) = saved_ipr[i];
ICCR = 1;
return 0;
static struct matrix_keypad_platform_data palmtc_keypad_platform_data = {
.keymap_data = &palmtc_keymap_data,
- .col_gpios = palmtc_keypad_row_gpios,
- .num_col_gpios = 12,
- .row_gpios = palmtc_keypad_col_gpios,
- .num_row_gpios = 4,
+ .row_gpios = palmtc_keypad_row_gpios,
+ .num_row_gpios = ARRAY_SIZE(palmtc_keypad_row_gpios),
+ .col_gpios = palmtc_keypad_col_gpios,
+ .num_col_gpios = ARRAY_SIZE(palmtc_keypad_col_gpios),
.active_low = 1,
.debounce_ms = 20,
pxa_set_i2c_info(NULL);
}
+#if defined(CONFIG_MACH_AKITA) || defined(CONFIG_MACH_BORZOI)
+static struct nand_bbt_descr sharpsl_akita_bbt = {
+ .options = 0,
+ .offs = 4,
+ .len = 1,
+ .pattern = scan_ff_pattern
+};
+
+static struct nand_ecclayout akita_oobinfo = {
+ .eccbytes = 24,
+ .eccpos = {
+ 0x5, 0x1, 0x2, 0x3, 0x6, 0x7, 0x15, 0x11,
+ 0x12, 0x13, 0x16, 0x17, 0x25, 0x21, 0x22, 0x23,
+ 0x26, 0x27, 0x35, 0x31, 0x32, 0x33, 0x36, 0x37},
+ .oobfree = {{0x08, 0x09}}
+};
+#endif
+
#if defined(CONFIG_MACH_SPITZ) || defined(CONFIG_MACH_BORZOI)
static void __init spitz_init(void)
{
spitz_ficp_platform_data.gpio_pwdown = SPITZ_GPIO_IR_ON;
+ if (machine_is_borzoi()) {
+ sharpsl_nand_platform_data.badblock_pattern = &sharpsl_akita_bbt;
+ sharpsl_nand_platform_data.ecc_layout = &akita_oobinfo;
+ }
+
platform_scoop_config = &spitz_pcmcia_config;
common_init();
},
};
-static struct nand_bbt_descr sharpsl_akita_bbt = {
- .options = 0,
- .offs = 4,
- .len = 1,
- .pattern = scan_ff_pattern
-};
-
-static struct nand_ecclayout akita_oobinfo = {
- .eccbytes = 24,
- .eccpos = {
- 0x5, 0x1, 0x2, 0x3, 0x6, 0x7, 0x15, 0x11,
- 0x12, 0x13, 0x16, 0x17, 0x25, 0x21, 0x22, 0x23,
- 0x26, 0x27, 0x35, 0x31, 0x32, 0x33, 0x36, 0x37},
- .oobfree = {{0x08, 0x09}}
-};
-
static void __init akita_init(void)
{
spitz_ficp_platform_data.gpio_pwdown = AKITA_GPIO_IR_ON;
bool "Support RealView/PBX platform"
select ARM_GIC
select HAVE_PATA_PLATFORM
+ select ARCH_SPARSEMEM_ENABLE if CPU_V7 && !HIGH_PHYS_OFFSET
+ select ZONE_DMA if SPARSEMEM
help
Include support for the ARM(R) RealView PBX platform.
0x70000000, 256MB of which being mirrored at 0x00000000. If
the board supports 512MB of RAM, this option allows the
memory to be accessed contiguously at the high physical
- offset.
+ offset. On the PBX board, disabling this option allows 1GB of
+ RAM to be used with SPARSEMEM.
endmenu
/* used by entry-macro.S and platsmp.c */
void __iomem *gic_cpu_base_addr;
+#ifdef CONFIG_ZONE_DMA
+/*
+ * Adjust the zones if there are restrictions for DMA access.
+ */
+void __init realview_adjust_zones(int node, unsigned long *size,
+ unsigned long *hole)
+{
+ unsigned long dma_size = SZ_256M >> PAGE_SHIFT;
+
+ if (!machine_is_realview_pbx() || node || (size[0] <= dma_size))
+ return;
+
+ size[ZONE_NORMAL] = size[0] - dma_size;
+ size[ZONE_DMA] = dma_size;
+ hole[ZONE_NORMAL] = hole[0];
+ hole[ZONE_DMA] = 0;
+}
+#endif
+
/*
* This is the RealView sched_clock implementation. This has
* a resolution of 41.7ns, and a maximum value of about 179s.
fb->panel = realview_clcd_panel();
fb->fb.screen_base = dma_alloc_writecombine(&fb->dev->dev, framesize,
- &dma, GFP_KERNEL);
+ &dma, GFP_KERNEL | GFP_DMA);
if (!fb->fb.screen_base) {
printk(KERN_ERR "CLCD: unable to map framebuffer\n");
return -ENOMEM;
realview_clocksource_init();
realview_clockevents_init(timer_irq);
}
+
+/*
+ * Setup the memory banks.
+ */
+void realview_fixup(struct machine_desc *mdesc, struct tag *tags, char **from,
+ struct meminfo *meminfo)
+{
+ /*
+ * Most RealView platforms have 512MB contiguous RAM at 0x70000000.
+ * Half of this is mirrored at 0.
+ */
+#ifdef CONFIG_REALVIEW_HIGH_PHYS_OFFSET
+ meminfo->bank[0].start = 0x70000000;
+ meminfo->bank[0].size = SZ_512M;
+ meminfo->nr_banks = 1;
+#else
+ meminfo->bank[0].start = 0;
+ meminfo->bank[0].size = SZ_256M;
+ meminfo->nr_banks = 1;
+#endif
+}
#include <linux/amba/bus.h>
#include <linux/io.h>
+#include <asm/setup.h>
#include <asm/leds.h>
#define AMBA_DEVICE(name,busid,base,plat) \
/* .dma = base##_DMA,*/ \
}
+struct machine_desc;
+
extern struct platform_device realview_flash_device;
extern struct platform_device realview_cf_device;
extern struct platform_device realview_i2c_device;
extern int realview_flash_register(struct resource *res, u32 num);
extern int realview_eth_register(const char *name, struct resource *res);
extern int realview_usb_register(struct resource *res);
+extern void realview_fixup(struct machine_desc *mdesc, struct tag *tags,
+ char **from, struct meminfo *meminfo);
extern void (*realview_reset)(char);
+
#endif
#define PHYS_OFFSET UL(0x00000000)
#endif
+#if !defined(__ASSEMBLY__) && defined(CONFIG_ZONE_DMA)
+extern void realview_adjust_zones(int node, unsigned long *size,
+ unsigned long *hole);
+#define arch_adjust_zones(node, size, hole) \
+ realview_adjust_zones(node, size, hole)
+
+#define ISA_DMA_THRESHOLD (PHYS_OFFSET + SZ_256M - 1)
+#define MAX_DMA_ADDRESS (PAGE_OFFSET + SZ_256M)
+#endif
+
+#ifdef CONFIG_SPARSEMEM
+
+/*
+ * Sparsemem definitions for RealView PBX.
+ *
+ * The RealView PBX board has another block of 512MB of RAM at 0x20000000,
+ * however only the block at 0x70000000 (or the 256MB mirror at 0x00000000)
+ * may be used for DMA.
+ *
+ * The macros below define a section size of 256MB and a non-linear virtual to
+ * physical mapping:
+ *
+ * 256MB @ 0x00000000 -> PAGE_OFFSET
+ * 512MB @ 0x20000000 -> PAGE_OFFSET + 0x10000000
+ * 256MB @ 0x80000000 -> PAGE_OFFSET + 0x30000000
+ */
+#ifdef CONFIG_REALVIEW_HIGH_PHYS_OFFSET
+#error "SPARSEMEM not available with REALVIEW_HIGH_PHYS_OFFSET"
+#endif
+
+#define MAX_PHYSMEM_BITS 32
+#define SECTION_SIZE_BITS 28
+
+/* bank page offsets */
+#define PAGE_OFFSET1 (PAGE_OFFSET + 0x10000000)
+#define PAGE_OFFSET2 (PAGE_OFFSET + 0x30000000)
+
+#define __phys_to_virt(phys) \
+ ((phys) >= 0x80000000 ? (phys) - 0x80000000 + PAGE_OFFSET2 : \
+ (phys) >= 0x20000000 ? (phys) - 0x20000000 + PAGE_OFFSET1 : \
+ (phys) + PAGE_OFFSET)
+
+#define __virt_to_phys(virt) \
+ ((virt) >= PAGE_OFFSET2 ? (virt) - PAGE_OFFSET2 + 0x80000000 : \
+ (virt) >= PAGE_OFFSET1 ? (virt) - PAGE_OFFSET1 + 0x20000000 : \
+ (virt) - PAGE_OFFSET)
+
+#endif /* CONFIG_SPARSEMEM */
+
#endif
* register. The BootMonitor waits for this register to become
* non-zero.
*/
-#define REALVIEW_SYS_FLAGSS_OFFSET 0x30
-#define REALVIEW_SYS_FLAGSC_OFFSET 0x34
__raw_writel(BSYM(virt_to_phys(realview_secondary_startup)),
- __io_address(REALVIEW_SYS_BASE) +
- REALVIEW_SYS_FLAGSS_OFFSET);
+ __io_address(REALVIEW_SYS_FLAGSSET));
mb();
}
.phys_io = REALVIEW_EB_UART0_BASE,
.io_pg_offst = (IO_ADDRESS(REALVIEW_EB_UART0_BASE) >> 18) & 0xfffc,
.boot_params = PHYS_OFFSET + 0x00000100,
+ .fixup = realview_fixup,
.map_io = realview_eb_map_io,
.init_irq = gic_init_irq,
.timer = &realview_eb_timer,
__raw_writel(REALVIEW_PB1176_SYS_LOCKVAL_RSTCTL, hdr_ctrl);
}
+static void realview_pb1176_fixup(struct machine_desc *mdesc,
+ struct tag *tags, char **from,
+ struct meminfo *meminfo)
+{
+ /*
+ * RealView PB1176 only has 128MB of RAM mapped at 0.
+ */
+ meminfo->bank[0].start = 0;
+ meminfo->bank[0].size = SZ_128M;
+ meminfo->nr_banks = 1;
+}
+
static void __init realview_pb1176_init(void)
{
int i;
.phys_io = REALVIEW_PB1176_UART0_BASE,
.io_pg_offst = (IO_ADDRESS(REALVIEW_PB1176_UART0_BASE) >> 18) & 0xfffc,
.boot_params = PHYS_OFFSET + 0x00000100,
+ .fixup = realview_pb1176_fixup,
.map_io = realview_pb1176_map_io,
.init_irq = gic_init_irq,
.timer = &realview_pb1176_timer,
.phys_io = REALVIEW_PB11MP_UART0_BASE,
.io_pg_offst = (IO_ADDRESS(REALVIEW_PB11MP_UART0_BASE) >> 18) & 0xfffc,
.boot_params = PHYS_OFFSET + 0x00000100,
+ .fixup = realview_fixup,
.map_io = realview_pb11mp_map_io,
.init_irq = gic_init_irq,
.timer = &realview_pb11mp_timer,
.phys_io = REALVIEW_PBA8_UART0_BASE,
.io_pg_offst = (IO_ADDRESS(REALVIEW_PBA8_UART0_BASE) >> 18) & 0xfffc,
.boot_params = PHYS_OFFSET + 0x00000100,
+ .fixup = realview_fixup,
.map_io = realview_pba8_map_io,
.init_irq = gic_init_irq,
.timer = &realview_pba8_timer,
.init = realview_pbx_timer_init,
};
+static void realview_pbx_fixup(struct machine_desc *mdesc, struct tag *tags,
+ char **from, struct meminfo *meminfo)
+{
+#ifdef CONFIG_SPARSEMEM
+ /*
+ * Memory configuration with SPARSEMEM enabled on RealView PBX (see
+ * asm/mach/memory.h for more information).
+ */
+ meminfo->bank[0].start = 0;
+ meminfo->bank[0].size = SZ_256M;
+ meminfo->bank[1].start = 0x20000000;
+ meminfo->bank[1].size = SZ_512M;
+ meminfo->bank[2].start = 0x80000000;
+ meminfo->bank[2].size = SZ_256M;
+ meminfo->nr_banks = 3;
+#else
+ realview_fixup(mdesc, tags, from, meminfo);
+#endif
+}
+
static void __init realview_pbx_init(void)
{
int i;
.phys_io = REALVIEW_PBX_UART0_BASE,
.io_pg_offst = (IO_ADDRESS(REALVIEW_PBX_UART0_BASE) >> 18) & 0xfffc,
.boot_params = PHYS_OFFSET + 0x00000100,
+ .fixup = realview_pbx_fixup,
.map_io = realview_pbx_map_io,
.init_irq = gic_init_irq,
.timer = &realview_pbx_timer,
#include <linux/io.h>
#include <mach/hardware.h>
+#include <mach/gpio-fns.h>
#include <asm/irq.h>
#include <mach/regs-gpio.h>
* waiting for reloads */
#define S3C2410_DMAF_AUTOSTART (1<<1) /* auto-start if buffer queued */
+#define S3C2410_DMAF_CIRCULAR (1 << 2) /* no circular dma support */
+
/* dma buffer */
struct s3c2410_dma_buf;
typedef unsigned long dma_device_t;
+static inline bool s3c_dma_has_circular(void)
+{
+ return false;
+}
+
#endif /* __ASM_ARCH_DMA_H */
select LEDS_TRIGGER_BACKLIGHT
select SND_S3C24XX_SOC_S3C24XX_UDA134X
select S3C_DEV_NAND
+ select S3C_DEV_USB_HOST
help
Say Y here to select support for the MINI2440. Is a 10cm x 10cm board
available via various sources. It can come with a 3.5" or 7" touch LCD.
.type = (S3C2410_LCDCON1_TFT16BPP |\
S3C2410_LCDCON1_TFT)
-struct s3c2410fb_display mini2440_lcd_cfg[] __initdata = {
+static struct s3c2410fb_display mini2440_lcd_cfg[] __initdata = {
[0] = { /* mini2440 + 3.5" TFT + touchscreen */
_LCD_DECLARE(
7, /* The 3.5 is quite fast */
#define S3C2410_GPCCON_MASK(x) (3 << ((x) * 2))
#define S3C2410_GPDCON_MASK(x) (3 << ((x) * 2))
-struct s3c2410fb_mach_info mini2440_fb_info __initdata = {
+static struct s3c2410fb_mach_info mini2440_fb_info __initdata = {
.displays = &mini2440_lcd_cfg[0], /* not constant! see init */
.num_displays = 1,
.default_display = 0,
DMACH_MAX /* the end */
};
-static __inline__ int s3c_dma_has_circular(void)
+static __inline__ bool s3c_dma_has_circular(void)
{
- /* we will be supporting ciruclar buffers as soon as we have DMA
- * engine support.
- */
- return 1;
+ return true;
}
#define S3C2410_DMAF_CIRCULAR (1 << 0)
depends on MACH_SMDK6410
select REGULATOR
select REGULATOR_WM8350
+ select S3C24XX_GPIO_EXTRA64
select MFD_WM8350_I2C
select MFD_WM8350_CONFIG_MODE_0
select MFD_WM8350_CONFIG_MODE_3
{
int i;
+ /* Configure the IRQ line */
+ s3c_gpio_setpull(S3C64XX_GPN(12), S3C_GPIO_PULL_UP);
+
/* Instantiate the regulators */
for (i = 0; i < ARRAY_SIZE(wm1190_regulators); i++)
wm8350_register_regulator(wm8350,
};
static struct platform_device rtc_device = {
- .name = "rtc0",
+ .name = "rtc-coh901331",
.id = -1,
.num_resources = ARRAY_SIZE(rtc_resources),
.resource = rtc_resources,
*/
__v7_setup:
#ifdef CONFIG_SMP
- mrc p15, 0, r0, c1, c0, 1 @ Enable SMP/nAMP mode and
- orr r0, r0, #(1 << 6) | (1 << 0) @ TLB ops broadcasting
- mcr p15, 0, r0, c1, c0, 1
+ mrc p15, 0, r0, c1, c0, 1
+ tst r0, #(1 << 6) @ SMP/nAMP mode enabled?
+ orreq r0, r0, #(1 << 6) | (1 << 0) @ Enable SMP/nAMP mode and
+ mcreq p15, 0, r0, c1, c0, 1 @ TLB ops broadcasting
#endif
adr r12, __v7_setup_stack @ the local stack
stmia r12, {r0-r5, r7, r9, r11, lr}
}
/* FIXME: what's the actual transition time? */
- policy->cpuinfo.transition_latency = 10 * 1000 * 1000;
+ policy->cpuinfo.transition_latency = 300 * 1000;
return 0;
}
static inline void omap2_enable_irq_lch(int lch)
{
u32 val;
+ unsigned long flags;
if (!cpu_class_is_omap2())
return;
+ spin_lock_irqsave(&dma_chan_lock, flags);
val = dma_read(IRQENABLE_L0);
val |= 1 << lch;
dma_write(val, IRQENABLE_L0);
+ spin_unlock_irqrestore(&dma_chan_lock, flags);
}
int omap_request_dma(int dev_id, const char *dev_name,
if (cpu_class_is_omap2()) {
u32 val;
+
+ spin_lock_irqsave(&dma_chan_lock, flags);
/* Disable interrupts */
val = dma_read(IRQENABLE_L0);
val &= ~(1 << lch);
dma_write(val, IRQENABLE_L0);
+ spin_unlock_irqrestore(&dma_chan_lock, flags);
/* Clear the CSR register and IRQ status register */
dma_write(OMAP2_DMA_CSR_CLEAR_MASK, CSR(lch));
{
int lch;
+ /*
+ * On OMAP1510, internal LCD controller will start the transfer
+ * when it gets enabled, so assume DMA running if LCD enabled.
+ */
+ if (cpu_is_omap1510())
+ if (omap_readw(0xfffec000 + 0x00) & (1 << 0))
+ return 1;
+
/* Check if LCD DMA is running */
if (cpu_is_omap16xx())
if (omap_readw(OMAP1610_DMA_LCD_CCR) & OMAP_DMA_CCR_EN)
#ifndef __ASM_PLAT_MFP_H
#define __ASM_PLAT_MFP_H
-#define mfp_to_gpio(m) ((m) % 128)
+#define mfp_to_gpio(m) ((m) % 256)
/* list of all the configurable MFP pins */
enum {
{
unsigned long val, flags;
- BUG_ON(mfp >= MFP_PIN_MAX);
+ BUG_ON(mfp < 0 || mfp >= MFP_PIN_MAX);
spin_lock_irqsave(&mfp_spin_lock, flags);
val = mfpr_readl(mfp_table[mfp].mfpr_off);
{
unsigned long flags;
- BUG_ON(mfp >= MFP_PIN_MAX);
+ BUG_ON(mfp < 0 || mfp >= MFP_PIN_MAX);
spin_lock_irqsave(&mfp_spin_lock, flags);
mfpr_writel(mfp_table[mfp].mfpr_off, val);
err:
return ret;
}
-EXPORT_SYMBOL_GPL(s3c_adc_convert);
+EXPORT_SYMBOL_GPL(s3c_adc_read);
static void s3c_adc_default_select(struct s3c_adc_client *client,
unsigned select)
static const char name_s3c2412[] = "S3C2412";
static const char name_s3c2440[] = "S3C2440";
static const char name_s3c2442[] = "S3C2442";
+static const char name_s3c2442b[] = "S3C2442B";
static const char name_s3c2443[] = "S3C2443";
static const char name_s3c2410a[] = "S3C2410A";
static const char name_s3c2440a[] = "S3C2440A";
.init = s3c2442_init,
.name = name_s3c2442
},
+ {
+ .idcode = 0x32440aab,
+ .idmask = 0xffffffff,
+ .map_io = s3c244x_map_io,
+ .init_clocks = s3c244x_init_clocks,
+ .init_uarts = s3c244x_init_uarts,
+ .init = s3c2442_init,
+ .name = name_s3c2442b
+ },
{
.idcode = 0x32412001,
.idmask = 0xffffffff,
{
unsigned long reload;
- pr_debug("s3c2410_chan_loadbuffer: loading buff %p (0x%08lx,0x%06x)\n",
- buf, (unsigned long)buf->data, buf->size);
-
if (buf == NULL) {
dmawarn("buffer is NULL\n");
return -EINVAL;
}
+ pr_debug("s3c2410_chan_loadbuffer: loading buff %p (0x%08lx,0x%06x)\n",
+ buf, (unsigned long)buf->data, buf->size);
+
/* check the state of the channel before we do anything */
if (chan->load_state == S3C2410_DMALOAD_1LOADED) {
#include <linux/io.h>
#include <mach/hardware.h>
+#include <mach/gpio-fns.h>
#include <asm/irq.h>
#include <mach/regs-gpio.h>
/* S3C2410 and compatible exported functions */
extern void s3c2410_cpufreq_setrefresh(struct s3c_cpufreq_config *cfg);
+extern void s3c2410_set_fvco(struct s3c_cpufreq_config *cfg);
+#ifdef CONFIG_S3C2410_IOTIMING
extern int s3c2410_iotiming_calc(struct s3c_cpufreq_config *cfg,
struct s3c_iotimings *iot);
extern void s3c2410_iotiming_set(struct s3c_cpufreq_config *cfg,
struct s3c_iotimings *iot);
-
-extern void s3c2410_set_fvco(struct s3c_cpufreq_config *cfg);
+#else
+#define s3c2410_iotiming_calc NULL
+#define s3c2410_iotiming_get NULL
+#define s3c2410_iotiming_set NULL
+#endif /* CONFIG_S3C2410_IOTIMING */
/* S3C2412 compatible routines */
#define s3c2410_init_uarts NULL
#define s3c2410_map_io NULL
#define s3c2410_init NULL
+#define s3c2410a_init NULL
#endif
extern int s3c2410_baseclk_add(void);
src = chan->dev_addr;
dst = data;
control0 = PL080_CONTROL_SRC_AHB2;
- control0 |= (u32)chan->hw_width << PL080_CONTROL_SWIDTH_SHIFT;
- control0 |= 2 << PL080_CONTROL_DWIDTH_SHIFT;
control0 |= PL080_CONTROL_DST_INCR;
break;
src = data;
dst = chan->dev_addr;
control0 = PL080_CONTROL_DST_AHB2;
- control0 |= (u32)chan->hw_width << PL080_CONTROL_DWIDTH_SHIFT;
- control0 |= 2 << PL080_CONTROL_SWIDTH_SHIFT;
control0 |= PL080_CONTROL_SRC_INCR;
break;
default:
control1 = size >> chan->hw_width; /* size in no of xfers */
control0 |= PL080_CONTROL_PROT_SYS; /* always in priv. mode */
control0 |= PL080_CONTROL_TC_IRQ_EN; /* always fire IRQ */
+ control0 |= (u32)chan->hw_width << PL080_CONTROL_DWIDTH_SHIFT;
+ control0 |= (u32)chan->hw_width << PL080_CONTROL_SWIDTH_SHIFT;
lli->src_addr = src;
lli->dst_addr = dst;
struct s3c64xx_dma_buff *next;
struct s3c64xx_dma_buff *buff;
struct pl080s_lli *lli;
+ unsigned long flags;
int ret;
WARN_ON(!chan);
s3c64xx_dma_fill_lli(chan, lli, data, size);
+ local_irq_save(flags);
+
if ((next = chan->next) != NULL) {
struct s3c64xx_dma_buff *end = chan->end;
struct pl080s_lli *endlli = end->lli;
s3c64xx_lli_to_regs(chan, lli);
}
+ local_irq_restore(flags);
+
show_lli(lli);
dbg_showchan(chan);
EXPORT_SYMBOL(s3c2410_dma_free);
-
-static void s3c64xx_dma_tcirq(struct s3c64xx_dmac *dmac, int offs)
-{
- struct s3c2410_dma_chan *chan = dmac->channels + offs;
-
- /* note, we currently do not bother to work out which buffer
- * or buffers have been completed since the last tc-irq. */
-
- if (chan->callback_fn)
- (chan->callback_fn)(chan, chan->curr->pw, 0, S3C2410_RES_OK);
-}
-
-static void s3c64xx_dma_errirq(struct s3c64xx_dmac *dmac, int offs)
-{
- printk(KERN_DEBUG "%s: offs %d\n", __func__, offs);
-}
-
static irqreturn_t s3c64xx_dma_irq(int irq, void *pw)
{
struct s3c64xx_dmac *dmac = pw;
+ struct s3c2410_dma_chan *chan;
+ enum s3c2410_dma_buffresult res;
u32 tcstat, errstat;
u32 bit;
int offs;
errstat = readl(dmac->regs + PL080_ERR_STATUS);
for (offs = 0, bit = 1; offs < 8; offs++, bit <<= 1) {
+ struct s3c64xx_dma_buff *buff;
+
+ if (!(errstat & bit) && !(tcstat & bit))
+ continue;
+
+ chan = dmac->channels + offs;
+ res = S3C2410_RES_ERR;
+
if (tcstat & bit) {
writel(bit, dmac->regs + PL080_TC_CLEAR);
- s3c64xx_dma_tcirq(dmac, offs);
+ res = S3C2410_RES_OK;
}
- if (errstat & bit) {
- s3c64xx_dma_errirq(dmac, offs);
+ if (errstat & bit)
writel(bit, dmac->regs + PL080_ERR_CLEAR);
+
+ /* 'next' points to the buffer that is next to the
+ * currently active buffer.
+ * For CIRCULAR queues, 'next' will be same as 'curr'
+ * when 'end' is the active buffer.
+ */
+ buff = chan->curr;
+ while (buff && buff != chan->next
+ && buff->next != chan->next)
+ buff = buff->next;
+
+ if (!buff)
+ BUG();
+
+ if (buff == chan->next)
+ buff = chan->end;
+
+ s3c64xx_dma_bufffdone(chan, buff, res);
+
+ /* Free the node and update curr, if non-circular queue */
+ if (!(chan->flags & S3C2410_DMAF_CIRCULAR)) {
+ chan->curr = buff->next;
+ s3c64xx_dma_freebuff(buff);
+ }
+
+ /* Update 'next' */
+ buff = chan->next;
+ if (chan->next == chan->end) {
+ chan->next = chan->curr;
+ if (!(chan->flags & S3C2410_DMAF_CIRCULAR))
+ chan->end = NULL;
+ } else {
+ chan->next = buff->next;
}
}
#define S3C6400_CLKDIV0_HCLK_SHIFT (8)
#define S3C6400_CLKDIV0_MPLL_MASK (0x1 << 4)
#define S3C6400_CLKDIV0_MPLL_SHIFT (4)
-#define S3C6400_CLKDIV0_ARM_MASK (0x3 << 0)
-#define S3C6410_CLKDIV0_ARM_MASK (0x7 << 0)
+#define S3C6400_CLKDIV0_ARM_MASK (0x7 << 0)
+#define S3C6410_CLKDIV0_ARM_MASK (0xf << 0)
#define S3C6400_CLKDIV0_ARM_SHIFT (0)
/* CLKDIV1 */
printk(KERN_DEBUG "%s: xtal is %ld\n", __func__, xtal);
+ /* For now assume the mux always selects the crystal */
+ clk_ext_xtal_mux.parent = xtal_clk;
+
epll = s3c6400_get_epll(xtal);
mpll = s3c6400_get_pll(xtal, __raw_readl(S3C_MPLL_CON));
apll = s3c6400_get_pll(xtal, __raw_readl(S3C_APLL_CON));
#define cpu_is_at91sam9263() (0)
#define cpu_is_at91sam9rl() (0)
#define cpu_is_at91cap9() (0)
+#define cpu_is_at91sam9g10() (0)
+#define cpu_is_at91sam9g45() (0)
+#define cpu_is_at91sam9g45es() (0)
#endif /* __ASM_ARCH_CPU_H */
select HAVE_IDE
select HAVE_OPROFILE
select INIT_ALL_POSSIBLE
+ select HAVE_KERNEL_GZIP
+ select HAVE_KERNEL_BZIP2
+ select HAVE_KERNEL_LZMA
config SBUS
bool
#
-# linux/arch/sh/boot/compressed/Makefile
+# linux/arch/m32r/boot/compressed/Makefile
#
# create a compressed vmlinux image from the original vmlinux
#
-targets := vmlinux vmlinux.bin vmlinux.bin.gz head.o misc.o \
- piggy.o vmlinux.lds
+targets := vmlinux vmlinux.bin vmlinux.bin.gz vmlinux.bin.bz2 \
+ vmlinux.bin.lzma head.o misc.o piggy.o vmlinux.lds
OBJECTS = $(obj)/head.o $(obj)/misc.o
$(obj)/vmlinux.bin.gz: $(obj)/vmlinux.bin FORCE
$(call if_changed,gzip)
+$(obj)/vmlinux.bin.bz2: $(obj)/vmlinux.bin FORCE
+ $(call if_changed,bzip2)
+
+$(obj)/vmlinux.bin.lzma: $(obj)/vmlinux.bin FORCE
+ $(call if_changed,lzma)
+
CFLAGS_misc.o += -fpic
ifdef CONFIG_MMU
OBJCOPYFLAGS += -R .empty_zero_page
-$(obj)/piggy.o: $(obj)/vmlinux.scr $(obj)/vmlinux.bin.gz FORCE
+suffix_$(CONFIG_KERNEL_GZIP) = gz
+suffix_$(CONFIG_KERNEL_BZIP2) = bz2
+suffix_$(CONFIG_KERNEL_LZMA) = lzma
+
+$(obj)/piggy.o: $(obj)/vmlinux.scr $(obj)/vmlinux.bin.$(suffix-y) FORCE
$(call if_changed,ld)
* Adapted for SH by Stuart Menefy, Aug 1999
*
* 2003-02-12: Support M32R by Takeo Takahashi
- * This is based on arch/sh/boot/compressed/misc.c.
*/
-#include <linux/string.h>
-
/*
* gzip declarations
*/
-
-#define OF(args) args
#define STATIC static
#undef memset
#undef memcpy
#define memzero(s, n) memset ((s), 0, (n))
-typedef unsigned char uch;
-typedef unsigned short ush;
-typedef unsigned long ulg;
-
-#define WSIZE 0x8000 /* Window size must be at least 32k, */
- /* and a power of two */
-
-static uch *inbuf; /* input buffer */
-static uch window[WSIZE]; /* Sliding window buffer */
-
-static unsigned insize = 0; /* valid bytes in inbuf */
-static unsigned inptr = 0; /* index of next byte to be processed in inbuf */
-static unsigned outcnt = 0; /* bytes in output buffer */
-
-/* gzip flag byte */
-#define ASCII_FLAG 0x01 /* bit 0 set: file probably ASCII text */
-#define CONTINUATION 0x02 /* bit 1 set: continuation of multi-part gzip file */
-#define EXTRA_FIELD 0x04 /* bit 2 set: extra field present */
-#define ORIG_NAME 0x08 /* bit 3 set: original file name present */
-#define COMMENT 0x10 /* bit 4 set: file comment present */
-#define ENCRYPTED 0x20 /* bit 5 set: file is encrypted */
-#define RESERVED 0xC0 /* bit 6,7: reserved */
-
-#define get_byte() (inptr < insize ? inbuf[inptr++] : fill_inbuf())
-
-/* Diagnostic functions */
-#ifdef DEBUG
-# define Assert(cond,msg) {if(!(cond)) error(msg);}
-# define Trace(x) fprintf x
-# define Tracev(x) {if (verbose) fprintf x ;}
-# define Tracevv(x) {if (verbose>1) fprintf x ;}
-# define Tracec(c,x) {if (verbose && (c)) fprintf x ;}
-# define Tracecv(c,x) {if (verbose>1 && (c)) fprintf x ;}
-#else
-# define Assert(cond,msg)
-# define Trace(x)
-# define Tracev(x)
-# define Tracevv(x)
-# define Tracec(c,x)
-# define Tracecv(c,x)
-#endif
-
-static int fill_inbuf(void);
-static void flush_window(void);
static void error(ch
git.samba.org / sfrench / cifs-2.6.git / commitdiff