Renesas MSIOF spi controller
Required properties:
-- compatible : "renesas,msiof-<soctype>" for SoCs,
- "renesas,sh-msiof" for SuperH, or
- "renesas,sh-mobile-msiof" for SH Mobile series.
- Examples with soctypes are:
- "renesas,msiof-r8a7790" (R-Car H2)
+- compatible : "renesas,msiof-r8a7790" (R-Car H2)
"renesas,msiof-r8a7791" (R-Car M2-W)
"renesas,msiof-r8a7792" (R-Car V2H)
"renesas,msiof-r8a7793" (R-Car M2-N)
"renesas,msiof-r8a7794" (R-Car E2)
"renesas,msiof-r8a7796" (R-Car M3-W)
"renesas,msiof-sh73a0" (SH-Mobile AG5)
+ "renesas,sh-mobile-msiof" (generic SH-Mobile compatibile device)
+ "renesas,rcar-gen2-msiof" (generic R-Car Gen2 compatible device)
+ "renesas,rcar-gen3-msiof" (generic R-Car Gen3 compatible device)
+ "renesas,sh-msiof" (deprecated)
+
+ When compatible with the generic version, nodes
+ must list the SoC-specific version corresponding
+ to the platform first followed by the generic
+ version.
+
- reg : A list of offsets and lengths of the register sets for
the device.
If only one register set is present, it is to be used
Example:
msiof0: spi@e6e20000 {
- compatible = "renesas,msiof-r8a7791";
+ compatible = "renesas,msiof-r8a7791",
+ "renesas,rcar-gen2-msiof";
reg = <0 0xe6e20000 0 0x0064>;
interrupts = <0 156 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp0_clks R8A7791_CLK_MSIOF0>;
+++ /dev/null
-Cirrus EP93xx SPI controller driver HOWTO
-=========================================
-
-ep93xx_spi driver brings SPI master support for EP93xx SPI controller. Chip
-selects are implemented with GPIO lines.
-
-NOTE: If possible, don't use SFRMOUT (SFRM1) signal as a chip select. It will
-not work correctly (it cannot be controlled by software). Use GPIO lines
-instead.
-
-Sample configuration
-====================
-
-Typically driver configuration is done in platform board files (the files under
-arch/arm/mach-ep93xx/*.c). In this example we configure MMC over SPI through
-this driver on TS-7260 board. You can adapt the code to suit your needs.
-
-This example uses EGPIO9 as SD/MMC card chip select (this is wired in DIO1
-header on the board).
-
-You need to select CONFIG_MMC_SPI to use mmc_spi driver.
-
-arch/arm/mach-ep93xx/ts72xx.c:
-
-...
-#include <linux/gpio.h>
-#include <linux/spi/spi.h>
-
-#include <linux/platform_data/spi-ep93xx.h>
-
-/* this is our GPIO line used for chip select */
-#define MMC_CHIP_SELECT_GPIO EP93XX_GPIO_LINE_EGPIO9
-
-static int ts72xx_mmc_spi_setup(struct spi_device *spi)
-{
- int err;
-
- err = gpio_request(MMC_CHIP_SELECT_GPIO, spi->modalias);
- if (err)
- return err;
-
- gpio_direction_output(MMC_CHIP_SELECT_GPIO, 1);
-
- return 0;
-}
-
-static void ts72xx_mmc_spi_cleanup(struct spi_device *spi)
-{
- gpio_set_value(MMC_CHIP_SELECT_GPIO, 1);
- gpio_direction_input(MMC_CHIP_SELECT_GPIO);
- gpio_free(MMC_CHIP_SELECT_GPIO);
-}
-
-static void ts72xx_mmc_spi_cs_control(struct spi_device *spi, int value)
-{
- gpio_set_value(MMC_CHIP_SELECT_GPIO, value);
-}
-
-static struct ep93xx_spi_chip_ops ts72xx_mmc_spi_ops = {
- .setup = ts72xx_mmc_spi_setup,
- .cleanup = ts72xx_mmc_spi_cleanup,
- .cs_control = ts72xx_mmc_spi_cs_control,
-};
-
-static struct spi_board_info ts72xx_spi_devices[] __initdata = {
- {
- .modalias = "mmc_spi",
- .controller_data = &ts72xx_mmc_spi_ops,
- /*
- * We use 10 MHz even though the maximum is 7.4 MHz. The driver
- * will limit it automatically to max. frequency.
- */
- .max_speed_hz = 10 * 1000 * 1000,
- .bus_num = 0,
- .chip_select = 0,
- .mode = SPI_MODE_0,
- },
-};
-
-static struct ep93xx_spi_info ts72xx_spi_info = {
- .num_chipselect = ARRAY_SIZE(ts72xx_spi_devices),
-};
-
-static void __init ts72xx_init_machine(void)
-{
- ...
- ep93xx_register_spi(&ts72xx_spi_info, ts72xx_spi_devices,
- ARRAY_SIZE(ts72xx_spi_devices));
-}
-
-The driver can use DMA for the transfers also. In this case ts72xx_spi_info
-becomes:
-
-static struct ep93xx_spi_info ts72xx_spi_info = {
- .num_chipselect = ARRAY_SIZE(ts72xx_spi_devices),
- .use_dma = true;
-};
-
-Note that CONFIG_EP93XX_DMA should be enabled as well.
-
-Thanks to
-=========
-Martin Guy, H. Hartley Sweeten and others who helped me during development of
-the driver. Simplemachines.it donated me a Sim.One board which I used testing
-the driver on EP9307.
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
-#include <linux/gpio.h>
#include <linux/i2c.h>
#include <linux/i2c-gpio.h>
#include <linux/spi/spi.h>
.gpio_nreset = -EINVAL, /* filled in later */
};
-static int edb93xx_cs4271_hw_setup(struct spi_device *spi)
-{
- return gpio_request_one(EP93XX_GPIO_LINE_EGPIO6,
- GPIOF_OUT_INIT_HIGH, spi->modalias);
-}
-
-static void edb93xx_cs4271_hw_cleanup(struct spi_device *spi)
-{
- gpio_free(EP93XX_GPIO_LINE_EGPIO6);
-}
-
-static void edb93xx_cs4271_hw_cs_control(struct spi_device *spi, int value)
-{
- gpio_set_value(EP93XX_GPIO_LINE_EGPIO6, value);
-}
-
-static struct ep93xx_spi_chip_ops edb93xx_cs4271_hw = {
- .setup = edb93xx_cs4271_hw_setup,
- .cleanup = edb93xx_cs4271_hw_cleanup,
- .cs_control = edb93xx_cs4271_hw_cs_control,
-};
-
static struct spi_board_info edb93xx_spi_board_info[] __initdata = {
{
.modalias = "cs4271",
.platform_data = &edb93xx_cs4271_data,
- .controller_data = &edb93xx_cs4271_hw,
.max_speed_hz = 6000000,
.bus_num = 0,
.chip_select = 0,
},
};
+static int edb93xx_spi_chipselects[] __initdata = {
+ EP93XX_GPIO_LINE_EGPIO6,
+};
+
static struct ep93xx_spi_info edb93xx_spi_info __initdata = {
- .num_chipselect = ARRAY_SIZE(edb93xx_spi_board_info),
+ .chipselect = edb93xx_spi_chipselects,
+ .num_chipselect = ARRAY_SIZE(edb93xx_spi_chipselects),
};
static void __init edb93xx_register_spi(void)
*/
#define MMC_CARD_DETECT_GPIO EP93XX_GPIO_LINE_EGPIO0
-/*
- * Up to v1.3, the Sim.One used SFRMOUT as SD card chip select, but this goes
- * low between multi-message command blocks. From v1.4, it uses a GPIO instead.
- * v1.3 parts will still work, since the signal on SFRMOUT is automatic.
- */
-#define MMC_CHIP_SELECT_GPIO EP93XX_GPIO_LINE_EGPIO1
-
-/*
- * MMC SPI chip select GPIO handling. If you are using SFRMOUT (SFRM1) signal,
- * you can leave these empty and pass NULL as .controller_data.
- */
-
-static int simone_mmc_spi_setup(struct spi_device *spi)
-{
- unsigned int gpio = MMC_CHIP_SELECT_GPIO;
- int err;
-
- err = gpio_request(gpio, spi->modalias);
- if (err)
- return err;
-
- err = gpio_direction_output(gpio, 1);
- if (err) {
- gpio_free(gpio);
- return err;
- }
-
- return 0;
-}
-
-static void simone_mmc_spi_cleanup(struct spi_device *spi)
-{
- unsigned int gpio = MMC_CHIP_SELECT_GPIO;
-
- gpio_set_value(gpio, 1);
- gpio_direction_input(gpio);
- gpio_free(gpio);
-}
-
-static void simone_mmc_spi_cs_control(struct spi_device *spi, int value)
-{
- gpio_set_value(MMC_CHIP_SELECT_GPIO, value);
-}
-
-static struct ep93xx_spi_chip_ops simone_mmc_spi_ops = {
- .setup = simone_mmc_spi_setup,
- .cleanup = simone_mmc_spi_cleanup,
- .cs_control = simone_mmc_spi_cs_control,
-};
-
/*
* MMC card detection GPIO setup.
*/
static struct spi_board_info simone_spi_devices[] __initdata = {
{
.modalias = "mmc_spi",
- .controller_data = &simone_mmc_spi_ops,
.platform_data = &simone_mmc_spi_data,
/*
* We use 10 MHz even though the maximum is 3.7 MHz. The driver
},
};
+/*
+ * Up to v1.3, the Sim.One used SFRMOUT as SD card chip select, but this goes
+ * low between multi-message command blocks. From v1.4, it uses a GPIO instead.
+ * v1.3 parts will still work, since the signal on SFRMOUT is automatic.
+ */
+static int simone_spi_chipselects[] __initdata = {
+ EP93XX_GPIO_LINE_EGPIO1,
+};
+
static struct ep93xx_spi_info simone_spi_info __initdata = {
- .num_chipselect = ARRAY_SIZE(simone_spi_devices),
+ .chipselect = simone_spi_chipselects,
+ .num_chipselect = ARRAY_SIZE(simone_spi_chipselects),
.use_dma = 1,
};
.gpio_nreset = EP93XX_GPIO_LINE_H(2),
};
-static int vision_cs4271_hw_setup(struct spi_device *spi)
-{
- return gpio_request_one(EP93XX_GPIO_LINE_EGPIO6,
- GPIOF_OUT_INIT_HIGH, spi->modalias);
-}
-
-static void vision_cs4271_hw_cleanup(struct spi_device *spi)
-{
- gpio_free(EP93XX_GPIO_LINE_EGPIO6);
-}
-
-static void vision_cs4271_hw_cs_control(struct spi_device *spi, int value)
-{
- gpio_set_value(EP93XX_GPIO_LINE_EGPIO6, value);
-}
-
-static struct ep93xx_spi_chip_ops vision_cs4271_hw = {
- .setup = vision_cs4271_hw_setup,
- .cleanup = vision_cs4271_hw_cleanup,
- .cs_control = vision_cs4271_hw_cs_control,
-};
-
/*************************************************************************
* SPI Flash
*************************************************************************/
-#define VISION_SPI_FLASH_CS EP93XX_GPIO_LINE_EGPIO7
-
static struct mtd_partition vision_spi_flash_partitions[] = {
{
.name = "SPI bootstrap",
.nr_parts = ARRAY_SIZE(vision_spi_flash_partitions),
};
-static int vision_spi_flash_hw_setup(struct spi_device *spi)
-{
- return gpio_request_one(VISION_SPI_FLASH_CS, GPIOF_INIT_HIGH,
- spi->modalias);
-}
-
-static void vision_spi_flash_hw_cleanup(struct spi_device *spi)
-{
- gpio_free(VISION_SPI_FLASH_CS);
-}
-
-static void vision_spi_flash_hw_cs_control(struct spi_device *spi, int value)
-{
- gpio_set_value(VISION_SPI_FLASH_CS, value);
-}
-
-static struct ep93xx_spi_chip_ops vision_spi_flash_hw = {
- .setup = vision_spi_flash_hw_setup,
- .cleanup = vision_spi_flash_hw_cleanup,
- .cs_control = vision_spi_flash_hw_cs_control,
-};
-
/*************************************************************************
* SPI SD/MMC host
*************************************************************************/
-#define VISION_SPI_MMC_CS EP93XX_GPIO_LINE_G(2)
-#define VISION_SPI_MMC_WP EP93XX_GPIO_LINE_F(0)
-#define VISION_SPI_MMC_CD EP93XX_GPIO_LINE_EGPIO15
-
static struct mmc_spi_platform_data vision_spi_mmc_data = {
.detect_delay = 100,
.powerup_msecs = 100,
.ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
.flags = MMC_SPI_USE_CD_GPIO | MMC_SPI_USE_RO_GPIO,
- .cd_gpio = VISION_SPI_MMC_CD,
+ .cd_gpio = EP93XX_GPIO_LINE_EGPIO15,
.cd_debounce = 1,
- .ro_gpio = VISION_SPI_MMC_WP,
+ .ro_gpio = EP93XX_GPIO_LINE_F(0),
.caps2 = MMC_CAP2_RO_ACTIVE_HIGH,
};
-static int vision_spi_mmc_hw_setup(struct spi_device *spi)
-{
- return gpio_request_one(VISION_SPI_MMC_CS, GPIOF_INIT_HIGH,
- spi->modalias);
-}
-
-static void vision_spi_mmc_hw_cleanup(struct spi_device *spi)
-{
- gpio_free(VISION_SPI_MMC_CS);
-}
-
-static void vision_spi_mmc_hw_cs_control(struct spi_device *spi, int value)
-{
- gpio_set_value(VISION_SPI_MMC_CS, value);
-}
-
-static struct ep93xx_spi_chip_ops vision_spi_mmc_hw = {
- .setup = vision_spi_mmc_hw_setup,
- .cleanup = vision_spi_mmc_hw_cleanup,
- .cs_control = vision_spi_mmc_hw_cs_control,
-};
-
/*************************************************************************
* SPI Bus
*************************************************************************/
{
.modalias = "cs4271",
.platform_data = &vision_cs4271_data,
- .controller_data = &vision_cs4271_hw,
.max_speed_hz = 6000000,
.bus_num = 0,
.chip_select = 0,
}, {
.modalias = "sst25l",
.platform_data = &vision_spi_flash_data,
- .controller_data = &vision_spi_flash_hw,
.max_speed_hz = 20000000,
.bus_num = 0,
.chip_select = 1,
}, {
.modalias = "mmc_spi",
.platform_data = &vision_spi_mmc_data,
- .controller_data = &vision_spi_mmc_hw,
.max_speed_hz = 20000000,
.bus_num = 0,
.chip_select = 2,
},
};
+static int vision_spi_chipselects[] __initdata = {
+ EP93XX_GPIO_LINE_EGPIO6,
+ EP93XX_GPIO_LINE_EGPIO7,
+ EP93XX_GPIO_LINE_G(2),
+};
+
static struct ep93xx_spi_info vision_spi_master __initdata = {
- .num_chipselect = ARRAY_SIZE(vision_spi_board_info),
+ .chipselect = vision_spi_chipselects,
+ .num_chipselect = ARRAY_SIZE(vision_spi_chipselects),
.use_dma = 1,
};
config SPI_BCM_QSPI
tristate "Broadcom BSPI and MSPI controller support"
- depends on ARCH_BRCMSTB || ARCH_BCM || ARCH_BCM_IPROC || COMPILE_TEST
+ depends on ARCH_BRCMSTB || ARCH_BCM || ARCH_BCM_IPROC || \
+ BMIPS_GENERIC || COMPILE_TEST
default ARCH_BCM_IPROC
help
Enables support for the Broadcom SPI flash and MSPI controller.
mode.
config SPI_FALCON
- tristate "Falcon SPI controller support"
+ bool "Falcon SPI controller support"
depends on SOC_FALCON
help
The external bus unit (EBU) found on the FALC-ON SoC has SPI
config SPI_FSL_DSPI
tristate "Freescale DSPI controller"
select REGMAP_MMIO
+ depends on HAS_DMA
depends on SOC_VF610 || SOC_LS1021A || ARCH_LAYERSCAPE || COMPILE_TEST
help
This enables support for the Freescale DSPI controller in master
val &= ~(A3700_SPI_DATA_PIN0 | A3700_SPI_DATA_PIN1);
switch (pin_mode) {
- case 1:
+ case SPI_NBITS_SINGLE:
break;
- case 2:
+ case SPI_NBITS_DUAL:
val |= A3700_SPI_DATA_PIN0;
break;
- case 4:
+ case SPI_NBITS_QUAD:
val |= A3700_SPI_DATA_PIN1;
break;
default:
spireg_write(a3700_spi, A3700_SPI_INT_STAT_REG, cause);
/* Wake up the transfer */
- if (a3700_spi->wait_mask & cause)
- complete(&a3700_spi->done);
+ complete(&a3700_spi->done);
return IRQ_HANDLED;
}
}
static void a3700_spi_transfer_setup(struct spi_device *spi,
- struct spi_transfer *xfer)
+ struct spi_transfer *xfer)
{
struct a3700_spi *a3700_spi;
unsigned int byte_len;
val = spireg_read(a3700_spi, A3700_SPI_DATA_IN_REG);
if (a3700_spi->buf_len >= 4) {
u32 data = le32_to_cpu(val);
+
memcpy(a3700_spi->rx_buf, &data, 4);
a3700_spi->buf_len -= 4;
struct spi_master *master;
struct a3700_spi *spi;
u32 num_cs = 0;
- int ret = 0;
+ int irq, ret = 0;
master = spi_alloc_master(dev, sizeof(*spi));
if (!master) {
master->unprepare_message = a3700_spi_unprepare_message;
master->set_cs = a3700_spi_set_cs;
master->flags = SPI_MASTER_HALF_DUPLEX;
- master->mode_bits |= (SPI_RX_DUAL | SPI_RX_DUAL |
+ master->mode_bits |= (SPI_RX_DUAL | SPI_TX_DUAL |
SPI_RX_QUAD | SPI_TX_QUAD);
platform_set_drvdata(pdev, master);
goto error;
}
- spi->irq = platform_get_irq(pdev, 0);
- if (spi->irq < 0) {
- dev_err(dev, "could not get irq: %d\n", spi->irq);
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0) {
+ dev_err(dev, "could not get irq: %d\n", irq);
ret = -ENXIO;
goto error;
}
+ spi->irq = irq;
init_completion(&spi->done);
struct a3700_spi *spi = spi_master_get_devdata(master);
clk_unprepare(spi->clk);
- spi_master_put(master);
return 0;
}
static struct platform_driver a3700_spi_driver = {
.driver = {
.name = DRIVER_NAME,
- .owner = THIS_MODULE,
.of_match_table = of_match_ptr(a3700_spi_dt_ids),
},
.probe = a3700_spi_probe,
ath79_spi_wr(sp, AR71XX_SPI_REG_IOC, sp->ioc_base);
}
- if (spi->chip_select) {
+ if (gpio_is_valid(spi->cs_gpio)) {
/* SPI is normally active-low */
- gpio_set_value(spi->cs_gpio, cs_high);
+ gpio_set_value_cansleep(spi->cs_gpio, cs_high);
} else {
+ u32 cs_bit = AR71XX_SPI_IOC_CS(spi->chip_select);
+
if (cs_high)
- sp->ioc_base |= AR71XX_SPI_IOC_CS0;
+ sp->ioc_base |= cs_bit;
else
- sp->ioc_base &= ~AR71XX_SPI_IOC_CS0;
+ sp->ioc_base &= ~cs_bit;
ath79_spi_wr(sp, AR71XX_SPI_REG_IOC, sp->ioc_base);
}
struct ath79_spi *sp = ath79_spidev_to_sp(spi);
int status;
- if (spi->chip_select && !gpio_is_valid(spi->cs_gpio))
- return -EINVAL;
-
status = 0;
- if (spi->chip_select) {
+ if (gpio_is_valid(spi->cs_gpio)) {
unsigned long flags;
flags = GPIOF_DIR_OUT;
status = gpio_request_one(spi->cs_gpio, flags,
dev_name(&spi->dev));
} else {
+ u32 cs_bit = AR71XX_SPI_IOC_CS(spi->chip_select);
+
if (spi->mode & SPI_CS_HIGH)
- sp->ioc_base &= ~AR71XX_SPI_IOC_CS0;
+ sp->ioc_base &= ~cs_bit;
else
- sp->ioc_base |= AR71XX_SPI_IOC_CS0;
+ sp->ioc_base |= cs_bit;
ath79_spi_wr(sp, AR71XX_SPI_REG_IOC, sp->ioc_base);
}
static void ath79_spi_cleanup_cs(struct spi_device *spi)
{
- if (spi->chip_select) {
+ if (gpio_is_valid(spi->cs_gpio)) {
gpio_free(spi->cs_gpio);
}
}
SPI_ENGINE_VERSION_MAJOR(version),
SPI_ENGINE_VERSION_MINOR(version),
SPI_ENGINE_VERSION_PATCH(version));
- return -ENODEV;
+ ret = -ENODEV;
+ goto err_put_master;
}
spi_engine->clk = devm_clk_get(&pdev->dev, "s_axi_aclk");
#define BSPI_BPP_MODE_SELECT_MASK BIT(8)
#define BSPI_BPP_ADDR_SELECT_MASK BIT(16)
-#define BSPI_READ_LENGTH 256
+#define BSPI_READ_LENGTH 512
/* MSPI register offsets */
#define MSPI_SPCR0_LSB 0x000
void *dev;
};
+
struct qspi_trans {
struct spi_transfer *trans;
int byte;
+ bool mspi_last_trans;
};
struct bcm_qspi {
return 0;
}
+static bool bcm_qspi_mspi_transfer_is_last(struct bcm_qspi *qspi,
+ struct qspi_trans *qt)
+{
+ if (qt->mspi_last_trans &&
+ spi_transfer_is_last(qspi->master, qt->trans))
+ return true;
+ else
+ return false;
+}
+
static int update_qspi_trans_byte_count(struct bcm_qspi *qspi,
struct qspi_trans *qt, int flags)
{
if (qt->byte >= qt->trans->len) {
/* we're at the end of the spi_transfer */
-
/* in TX mode, need to pause for a delay or CS change */
if (qt->trans->delay_usecs &&
(flags & TRANS_STATUS_BREAK_DELAY))
goto done;
dev_dbg(&qspi->pdev->dev, "advance msg exit\n");
- if (spi_transfer_is_last(qspi->master, qt->trans))
+ if (bcm_qspi_mspi_transfer_is_last(qspi, qt))
ret = TRANS_STATUS_BREAK_EOM;
else
ret = TRANS_STATUS_BREAK_NO_BYTES;
struct spi_flash_read_message *msg)
{
struct bcm_qspi *qspi = spi_master_get_devdata(spi->master);
- u32 addr = 0, len, len_words;
+ u32 addr = 0, len, rdlen, len_words;
int ret = 0;
unsigned long timeo = msecs_to_jiffies(100);
struct bcm_qspi_soc_intc *soc_intc = qspi->soc_intc;
bcm_qspi_write(qspi, MSPI, MSPI_WRITE_LOCK, 0);
/*
- * when using flex mode mode we need to send
+ * when using flex mode we need to send
* the upper address byte to bspi
*/
if (bcm_qspi_bspi_ver_three(qspi) == false) {
else
addr = msg->from & 0x00ffffff;
- /* set BSPI RAF buffer max read length */
- len = msg->len;
- if (len > BSPI_READ_LENGTH)
- len = BSPI_READ_LENGTH;
-
if (bcm_qspi_bspi_ver_three(qspi) == true)
addr = (addr + 0xc00000) & 0xffffff;
- reinit_completion(&qspi->bspi_done);
- bcm_qspi_enable_bspi(qspi);
- len_words = (len + 3) >> 2;
- qspi->bspi_rf_msg = msg;
- qspi->bspi_rf_msg_status = 0;
+ /*
+ * read into the entire buffer by breaking the reads
+ * into RAF buffer read lengths
+ */
+ len = msg->len;
qspi->bspi_rf_msg_idx = 0;
- qspi->bspi_rf_msg_len = len;
- dev_dbg(&qspi->pdev->dev, "bspi xfr addr 0x%x len 0x%x", addr, len);
- bcm_qspi_write(qspi, BSPI, BSPI_RAF_START_ADDR, addr);
- bcm_qspi_write(qspi, BSPI, BSPI_RAF_NUM_WORDS, len_words);
- bcm_qspi_write(qspi, BSPI, BSPI_RAF_WATERMARK, 0);
+ do {
+ if (len > BSPI_READ_LENGTH)
+ rdlen = BSPI_READ_LENGTH;
+ else
+ rdlen = len;
+
+ reinit_completion(&qspi->bspi_done);
+ bcm_qspi_enable_bspi(qspi);
+ len_words = (rdlen + 3) >> 2;
+ qspi->bspi_rf_msg = msg;
+ qspi->bspi_rf_msg_status = 0;
+ qspi->bspi_rf_msg_len = rdlen;
+ dev_dbg(&qspi->pdev->dev,
+ "bspi xfr addr 0x%x len 0x%x", addr, rdlen);
+ bcm_qspi_write(qspi, BSPI, BSPI_RAF_START_ADDR, addr);
+ bcm_qspi_write(qspi, BSPI, BSPI_RAF_NUM_WORDS, len_words);
+ bcm_qspi_write(qspi, BSPI, BSPI_RAF_WATERMARK, 0);
+ if (qspi->soc_intc) {
+ /*
+ * clear soc MSPI and BSPI interrupts and enable
+ * BSPI interrupts.
+ */
+ soc_intc->bcm_qspi_int_ack(soc_intc, MSPI_BSPI_DONE);
+ soc_intc->bcm_qspi_int_set(soc_intc, BSPI_DONE, true);
+ }
- if (qspi->soc_intc) {
- /*
- * clear soc MSPI and BSPI interrupts and enable
- * BSPI interrupts.
- */
- soc_intc->bcm_qspi_int_ack(soc_intc, MSPI_BSPI_DONE);
- soc_intc->bcm_qspi_int_set(soc_intc, BSPI_DONE, true);
+ /* Must flush previous writes before starting BSPI operation */
+ mb();
+ bcm_qspi_bspi_lr_start(qspi);
+ if (!wait_for_completion_timeout(&qspi->bspi_done, timeo)) {
+ dev_err(&qspi->pdev->dev, "timeout waiting for BSPI\n");
+ ret = -ETIMEDOUT;
+ break;
+ }
+
+ /* set msg return length */
+ msg->retlen += rdlen;
+ addr += rdlen;
+ len -= rdlen;
+ } while (len);
+
+ return ret;
+}
+
+static int bcm_qspi_transfer_one(struct spi_master *master,
+ struct spi_device *spi,
+ struct spi_transfer *trans)
+{
+ struct bcm_qspi *qspi = spi_master_get_devdata(master);
+ int slots;
+ unsigned long timeo = msecs_to_jiffies(100);
+
+ bcm_qspi_chip_select(qspi, spi->chip_select);
+ qspi->trans_pos.trans = trans;
+ qspi->trans_pos.byte = 0;
+
+ while (qspi->trans_pos.byte < trans->len) {
+ reinit_completion(&qspi->mspi_done);
+
+ slots = write_to_hw(qspi, spi);
+ if (!wait_for_completion_timeout(&qspi->mspi_done, timeo)) {
+ dev_err(&qspi->pdev->dev, "timeout waiting for MSPI\n");
+ return -ETIMEDOUT;
+ }
+
+ read_from_hw(qspi, slots);
}
- /* Must flush previous writes before starting BSPI operation */
- mb();
+ return 0;
+}
- bcm_qspi_bspi_lr_start(qspi);
- if (!wait_for_completion_timeout(&qspi->bspi_done, timeo)) {
- dev_err(&qspi->pdev->dev, "timeout waiting for BSPI\n");
- ret = -ETIMEDOUT;
- } else {
- /* set the return length for the caller */
- msg->retlen = len;
+static int bcm_qspi_mspi_flash_read(struct spi_device *spi,
+ struct spi_flash_read_message *msg)
+{
+ struct bcm_qspi *qspi = spi_master_get_devdata(spi->master);
+ struct spi_transfer t[2];
+ u8 cmd[6];
+ int ret;
+
+ memset(cmd, 0, sizeof(cmd));
+ memset(t, 0, sizeof(t));
+
+ /* tx */
+ /* opcode is in cmd[0] */
+ cmd[0] = msg->read_opcode;
+ cmd[1] = msg->from >> (msg->addr_width * 8 - 8);
+ cmd[2] = msg->from >> (msg->addr_width * 8 - 16);
+ cmd[3] = msg->from >> (msg->addr_width * 8 - 24);
+ cmd[4] = msg->from >> (msg->addr_width * 8 - 32);
+ t[0].tx_buf = cmd;
+ t[0].len = msg->addr_width + msg->dummy_bytes + 1;
+ t[0].bits_per_word = spi->bits_per_word;
+ t[0].tx_nbits = msg->opcode_nbits;
+ /* lets mspi know that this is not last transfer */
+ qspi->trans_pos.mspi_last_trans = false;
+ ret = bcm_qspi_transfer_one(spi->master, spi, &t[0]);
+
+ /* rx */
+ qspi->trans_pos.mspi_last_trans = true;
+ if (!ret) {
+ /* rx */
+ t[1].rx_buf = msg->buf;
+ t[1].len = msg->len;
+ t[1].rx_nbits = msg->data_nbits;
+ t[1].bits_per_word = spi->bits_per_word;
+ ret = bcm_qspi_transfer_one(spi->master, spi, &t[1]);
}
+ if (!ret)
+ msg->retlen = msg->len;
+
return ret;
}
mspi_read = true;
if (mspi_read)
- /* this will make the m25p80 read to fallback to mspi read */
- return -EAGAIN;
+ return bcm_qspi_mspi_flash_read(spi, msg);
io_width = msg->data_nbits ? msg->data_nbits : SPI_NBITS_SINGLE;
addrlen = msg->addr_width;
return ret;
}
-static int bcm_qspi_transfer_one(struct spi_master *master,
- struct spi_device *spi,
- struct spi_transfer *trans)
-{
- struct bcm_qspi *qspi = spi_master_get_devdata(master);
- int slots;
- unsigned long timeo = msecs_to_jiffies(100);
-
- bcm_qspi_chip_select(qspi, spi->chip_select);
- qspi->trans_pos.trans = trans;
- qspi->trans_pos.byte = 0;
-
- while (qspi->trans_pos.byte < trans->len) {
- reinit_completion(&qspi->mspi_done);
-
- slots = write_to_hw(qspi, spi);
- if (!wait_for_completion_timeout(&qspi->mspi_done, timeo)) {
- dev_err(&qspi->pdev->dev, "timeout waiting for MSPI\n");
- return -ETIMEDOUT;
- }
-
- read_from_hw(qspi, slots);
- }
-
- return 0;
-}
-
static void bcm_qspi_cleanup(struct spi_device *spi)
{
struct bcm_qspi_parms *xp = spi_get_ctldata(spi);
qspi->pdev = pdev;
qspi->trans_pos.trans = NULL;
qspi->trans_pos.byte = 0;
+ qspi->trans_pos.mspi_last_trans = true;
qspi->master = master;
master->bus_num = -1;
{
struct bcm_qspi *qspi = platform_get_drvdata(pdev);
- platform_set_drvdata(pdev, NULL);
bcm_qspi_hw_uninit(qspi);
clk_disable_unprepare(qspi->clk);
kfree(qspi->dev_ids);
+/*
+ * Copyright (C) 2014-2016 Rafał Miłecki <rafal@milecki.pl>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
#include <linux/kernel.h>
* BCMA
**************************************************/
-static struct spi_board_info bcm53xx_info = {
- .modalias = "bcm53xxspiflash",
-};
-
static const struct bcma_device_id bcm53xxspi_bcma_tbl[] = {
BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_NS_QSPI, BCMA_ANY_REV, BCMA_ANY_CLASS),
{},
b53spi->bspi = true;
bcm53xxspi_disable_bspi(b53spi);
+ master->dev.of_node = dev->of_node;
master->transfer_one = bcm53xxspi_transfer_one;
if (b53spi->mmio_base)
master->spi_flash_read = bcm53xxspi_flash_read;
return err;
}
- /* Broadcom SoCs (at least with the CC rev 42) use SPI for flash only */
- spi_new_device(master, &bcm53xx_info);
-
return 0;
}
MODULE_DESCRIPTION("Broadcom BCM53xx SPI Controller driver");
MODULE_AUTHOR("Rafał Miłecki <zajec5@gmail.com>");
-MODULE_LICENSE("GPL");
+MODULE_LICENSE("GPL v2");
buf = t->rx_buf;
t->rx_dma = dma_map_single(&spi->dev, buf,
t->len, DMA_FROM_DEVICE);
- if (!t->rx_dma) {
+ if (dma_mapping_error(&spi->dev, !t->rx_dma)) {
ret = -EFAULT;
goto err_rx_map;
}
buf = (void *)t->tx_buf;
t->tx_dma = dma_map_single(&spi->dev, buf,
t->len, DMA_TO_DEVICE);
- if (!t->tx_dma) {
+ if (dma_mapping_error(&spi->dev, t->tx_dma)) {
ret = -EFAULT;
goto err_tx_map;
}
static void mid_spi_dma_stop(struct dw_spi *dws)
{
if (test_bit(TX_BUSY, &dws->dma_chan_busy)) {
- dmaengine_terminate_all(dws->txchan);
+ dmaengine_terminate_sync(dws->txchan);
clear_bit(TX_BUSY, &dws->dma_chan_busy);
}
if (test_bit(RX_BUSY, &dws->dma_chan_busy)) {
- dmaengine_terminate_all(dws->rxchan);
+ dmaengine_terminate_sync(dws->rxchan);
clear_bit(RX_BUSY, &dws->dma_chan_busy);
}
}
static int dw_spi_debugfs_init(struct dw_spi *dws)
{
- dws->debugfs = debugfs_create_dir("dw_spi", NULL);
+ char name[32];
+
+ snprintf(name, 32, "dw_spi%d", dws->master->bus_num);
+ dws->debugfs = debugfs_create_dir(name, NULL);
if (!dws->debugfs)
return -ENOMEM;
dws->type = SSI_MOTO_SPI;
dws->dma_inited = 0;
dws->dma_addr = (dma_addr_t)(dws->paddr + DW_SPI_DR);
- snprintf(dws->name, sizeof(dws->name), "dw_spi%d", dws->bus_num);
- ret = request_irq(dws->irq, dw_spi_irq, IRQF_SHARED, dws->name, master);
+ ret = request_irq(dws->irq, dw_spi_irq, IRQF_SHARED, dev_name(dev),
+ master);
if (ret < 0) {
dev_err(dev, "can not get IRQ\n");
goto err_free_master;
struct dw_spi {
struct spi_master *master;
enum dw_ssi_type type;
- char name[16];
void __iomem *regs;
unsigned long paddr;
#include <linux/platform_device.h>
#include <linux/sched.h>
#include <linux/scatterlist.h>
+#include <linux/gpio.h>
#include <linux/spi/spi.h>
#include <linux/platform_data/dma-ep93xx.h>
void *zeropage;
};
-/**
- * struct ep93xx_spi_chip - SPI device hardware settings
- * @spi: back pointer to the SPI device
- * @ops: private chip operations
- */
-struct ep93xx_spi_chip {
- const struct spi_device *spi;
- struct ep93xx_spi_chip_ops *ops;
-};
-
/* converts bits per word to CR0.DSS value */
#define bits_per_word_to_dss(bpw) ((bpw) - 1)
return -EINVAL;
}
-static void ep93xx_spi_cs_control(struct spi_device *spi, bool control)
-{
- struct ep93xx_spi_chip *chip = spi_get_ctldata(spi);
- int value = (spi->mode & SPI_CS_HIGH) ? control : !control;
-
- if (chip->ops && chip->ops->cs_control)
- chip->ops->cs_control(spi, value);
-}
-
-/**
- * ep93xx_spi_setup() - setup an SPI device
- * @spi: SPI device to setup
- *
- * This function sets up SPI device mode, speed etc. Can be called multiple
- * times for a single device. Returns %0 in case of success, negative error in
- * case of failure. When this function returns success, the device is
- * deselected.
- */
-static int ep93xx_spi_setup(struct spi_device *spi)
+static void ep93xx_spi_cs_control(struct spi_device *spi, bool enable)
{
- struct ep93xx_spi *espi = spi_master_get_devdata(spi->master);
- struct ep93xx_spi_chip *chip;
+ if (spi->mode & SPI_CS_HIGH)
+ enable = !enable;
- chip = spi_get_ctldata(spi);
- if (!chip) {
- dev_dbg(&espi->pdev->dev, "initial setup for %s\n",
- spi->modalias);
-
- chip = kzalloc(sizeof(*chip), GFP_KERNEL);
- if (!chip)
- return -ENOMEM;
-
- chip->spi = spi;
- chip->ops = spi->controller_data;
-
- if (chip->ops && chip->ops->setup) {
- int ret = chip->ops->setup(spi);
-
- if (ret) {
- kfree(chip);
- return ret;
- }
- }
-
- spi_set_ctldata(spi, chip);
- }
-
- ep93xx_spi_cs_control(spi, false);
- return 0;
+ if (gpio_is_valid(spi->cs_gpio))
+ gpio_set_value(spi->cs_gpio, !enable);
}
-/**
- * ep93xx_spi_cleanup() - cleans up master controller specific state
- * @spi: SPI device to cleanup
- *
- * This function releases master controller specific state for given @spi
- * device.
- */
-static void ep93xx_spi_cleanup(struct spi_device *spi)
-{
- struct ep93xx_spi_chip *chip;
-
- chip = spi_get_ctldata(spi);
- if (chip) {
- if (chip->ops && chip->ops->cleanup)
- chip->ops->cleanup(spi);
- spi_set_ctldata(spi, NULL);
- kfree(chip);
- }
-}
-
-/**
- * ep93xx_spi_chip_setup() - configures hardware according to given @chip
- * @espi: ep93xx SPI controller struct
- * @chip: chip specific settings
- * @speed_hz: transfer speed
- * @bits_per_word: transfer bits_per_word
- */
static int ep93xx_spi_chip_setup(const struct ep93xx_spi *espi,
- const struct ep93xx_spi_chip *chip,
- u32 speed_hz, u8 bits_per_word)
+ struct spi_device *spi,
+ struct spi_transfer *xfer)
{
- u8 dss = bits_per_word_to_dss(bits_per_word);
+ u8 dss = bits_per_word_to_dss(xfer->bits_per_word);
u8 div_cpsr = 0;
u8 div_scr = 0;
u16 cr0;
int err;
- err = ep93xx_spi_calc_divisors(espi, speed_hz, &div_cpsr, &div_scr);
+ err = ep93xx_spi_calc_divisors(espi, xfer->speed_hz,
+ &div_cpsr, &div_scr);
if (err)
return err;
cr0 = div_scr << SSPCR0_SCR_SHIFT;
- cr0 |= (chip->spi->mode & (SPI_CPHA|SPI_CPOL)) << SSPCR0_MODE_SHIFT;
+ cr0 |= (spi->mode & (SPI_CPHA | SPI_CPOL)) << SSPCR0_MODE_SHIFT;
cr0 |= dss;
dev_dbg(&espi->pdev->dev, "setup: mode %d, cpsr %d, scr %d, dss %d\n",
- chip->spi->mode, div_cpsr, div_scr, dss);
+ spi->mode, div_cpsr, div_scr, dss);
dev_dbg(&espi->pdev->dev, "setup: cr0 %#x\n", cr0);
ep93xx_spi_write_u8(espi, SSPCPSR, div_cpsr);
struct spi_message *msg,
struct spi_transfer *t)
{
- struct ep93xx_spi_chip *chip = spi_get_ctldata(msg->spi);
int err;
msg->state = t;
- err = ep93xx_spi_chip_setup(espi, chip, t->speed_hz, t->bits_per_word);
+ err = ep93xx_spi_chip_setup(espi, msg->spi, t);
if (err) {
dev_err(&espi->pdev->dev,
"failed to setup chip for transfer\n");
struct resource *res;
int irq;
int error;
+ int i;
info = dev_get_platdata(&pdev->dev);
+ if (!info) {
+ dev_err(&pdev->dev, "missing platform data\n");
+ return -EINVAL;
+ }
irq = platform_get_irq(pdev, 0);
if (irq < 0) {
if (!master)
return -ENOMEM;
- master->setup = ep93xx_spi_setup;
master->transfer_one_message = ep93xx_spi_transfer_one_message;
- master->cleanup = ep93xx_spi_cleanup;
master->bus_num = pdev->id;
- master->num_chipselect = info->num_chipselect;
master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
master->bits_per_word_mask = SPI_BPW_RANGE_MASK(4, 16);
+ master->num_chipselect = info->num_chipselect;
+ master->cs_gpios = devm_kzalloc(&master->dev,
+ sizeof(int) * master->num_chipselect,
+ GFP_KERNEL);
+ if (!master->cs_gpios) {
+ error = -ENOMEM;
+ goto fail_release_master;
+ }
+
+ for (i = 0; i < master->num_chipselect; i++) {
+ master->cs_gpios[i] = info->chipselect[i];
+
+ if (!gpio_is_valid(master->cs_gpios[i]))
+ continue;
+
+ error = devm_gpio_request_one(&pdev->dev, master->cs_gpios[i],
+ GPIOF_OUT_INIT_HIGH,
+ "ep93xx-spi");
+ if (error) {
+ dev_err(&pdev->dev, "could not request cs gpio %d\n",
+ master->cs_gpios[i]);
+ goto fail_release_master;
+ }
+ }
+
platform_set_drvdata(pdev, master);
espi = spi_master_get_devdata(master);
struct spi_transfer *xfer;
bool is_first_xfer = true;
u32 temp;
- int ret;
+ int ret = 0;
msg->status = 0;
msg->actual_length = 0;
static struct platform_driver fsl_lpspi_driver = {
.driver = {
- .name = DRIVER_NAME,
- .of_match_table = fsl_lpspi_dt_ids,
- },
+ .name = DRIVER_NAME,
+ .of_match_table = fsl_lpspi_dt_ids,
+ },
.probe = fsl_lpspi_probe,
.remove = fsl_lpspi_remove,
};
if ((mpc8xxx_spi->spibrg / hz) > 64) {
cs->hw_mode |= SPMODE_DIV16;
pm = (mpc8xxx_spi->spibrg - 1) / (hz * 64) + 1;
-
- WARN_ONCE(pm > 16, "%s: Requested speed is too low: %d Hz. "
- "Will use %d Hz instead.\n", dev_name(&spi->dev),
- hz, mpc8xxx_spi->spibrg / 1024);
+ WARN_ONCE(pm > 16,
+ "%s: Requested speed is too low: %d Hz. Will use %d Hz instead.\n",
+ dev_name(&spi->dev), hz, mpc8xxx_spi->spibrg / 1024);
if (pm > 16)
pm = 16;
} else {
return 0;
}
- pinfo->gpios = kmalloc(ngpios * sizeof(*pinfo->gpios), GFP_KERNEL);
+ pinfo->gpios = kmalloc_array(ngpios, sizeof(*pinfo->gpios),
+ GFP_KERNEL);
if (!pinfo->gpios)
return -ENOMEM;
memset(pinfo->gpios, -1, ngpios * sizeof(*pinfo->gpios));
- pinfo->alow_flags = kzalloc(ngpios * sizeof(*pinfo->alow_flags),
+ pinfo->alow_flags = kcalloc(ngpios, sizeof(*pinfo->alow_flags),
GFP_KERNEL);
if (!pinfo->alow_flags) {
ret = -ENOMEM;
ret = gpio_direction_output(pinfo->gpios[i],
pinfo->alow_flags[i]);
if (ret) {
- dev_err(dev, "can't set output direction for gpio "
- "#%d: %d\n", i, ret);
+ dev_err(dev,
+ "can't set output direction for gpio #%d: %d\n",
+ i, ret);
goto err_loop;
}
}
struct spi_transfer *transfer)
{
struct spi_imx_data *spi_imx = spi_master_get_devdata(master);
- unsigned int bpw;
+ unsigned int bpw, i;
if (!master->dma_rx)
return false;
if (bpw != 1 && bpw != 2 && bpw != 4)
return false;
- if (transfer->len < spi_imx->wml * bpw)
- return false;
+ for (i = spi_imx_get_fifosize(spi_imx) / 2; i > 0; i--) {
+ if (!(transfer->len % (i * bpw)))
+ break;
+ }
- if (transfer->len % (spi_imx->wml * bpw))
+ if (i == 0)
return false;
+ spi_imx->wml = i;
+
return true;
}
struct dma_slave_config rx = {}, tx = {};
struct spi_imx_data *spi_imx = spi_master_get_devdata(master);
- if (bytes_per_word == spi_imx->bytes_per_word)
- /* Same as last time */
- return 0;
-
switch (bytes_per_word) {
case 4:
buswidth = DMA_SLAVE_BUSWIDTH_4_BYTES;
ms->gpio_cs_count = of_gpio_count(op->dev.of_node);
if (ms->gpio_cs_count > 0) {
master->num_chipselect = ms->gpio_cs_count;
- ms->gpio_cs = kmalloc(ms->gpio_cs_count * sizeof(unsigned int),
- GFP_KERNEL);
+ ms->gpio_cs = kmalloc_array(ms->gpio_cs_count,
+ sizeof(*ms->gpio_cs),
+ GFP_KERNEL);
if (!ms->gpio_cs) {
rc = -ENOMEM;
goto err_alloc_gpio;
gpio_cs = of_get_gpio(op->dev.of_node, i);
if (gpio_cs < 0) {
dev_err(&op->dev,
- "could not parse the gpio field "
- "in oftree\n");
+ "could not parse the gpio field in oftree\n");
rc = -ENODEV;
goto err_gpio;
}
rc = gpio_request(gpio_cs, dev_name(&op->dev));
if (rc) {
dev_err(&op->dev,
- "can't request spi cs gpio #%d "
- "on gpio line %d\n", i, gpio_cs);
+ "can't request spi cs gpio #%d on gpio line %d\n",
+ i, gpio_cs);
goto err_gpio;
}
#define MTK_SPI_IDLE 0
#define MTK_SPI_PAUSED 1
-#define MTK_SPI_MAX_FIFO_SIZE 32
+#define MTK_SPI_MAX_FIFO_SIZE 32U
#define MTK_SPI_PACKET_SIZE 1024
struct mtk_spi_compatible {
struct mtk_spi *mdata = spi_master_get_devdata(master);
mdata->cur_transfer = xfer;
- mdata->xfer_len = xfer->len;
+ mdata->xfer_len = min(MTK_SPI_MAX_FIFO_SIZE, xfer->len);
mtk_spi_prepare_transfer(master, xfer);
mtk_spi_setup_packet(master);
struct spi_device *spi,
struct spi_transfer *xfer)
{
- return xfer->len > MTK_SPI_MAX_FIFO_SIZE;
+ /* Buffers for DMA transactions must be 4-byte aligned */
+ return (xfer->len > MTK_SPI_MAX_FIFO_SIZE &&
+ (unsigned long)xfer->tx_buf % 4 == 0 &&
+ (unsigned long)xfer->rx_buf % 4 == 0);
}
static int mtk_spi_setup(struct spi_device *spi)
®_val, remainder);
}
}
- spi_finalize_current_transfer(master);
+
+ trans->len -= mdata->xfer_len;
+ if (!trans->len) {
+ spi_finalize_current_transfer(master);
+ return IRQ_HANDLED;
+ }
+
+ if (trans->tx_buf)
+ trans->tx_buf += mdata->xfer_len;
+ if (trans->rx_buf)
+ trans->rx_buf += mdata->xfer_len;
+
+ mdata->xfer_len = min(MTK_SPI_MAX_FIFO_SIZE, trans->len);
+ mtk_spi_setup_packet(master);
+
+ cnt = trans->len / 4;
+ iowrite32_rep(mdata->base + SPI_TX_DATA_REG, trans->tx_buf, cnt);
+
+ remainder = trans->len % 4;
+ if (remainder > 0) {
+ reg_val = 0;
+ memcpy(®_val, trans->tx_buf + (cnt * 4), remainder);
+ writel(reg_val, mdata->base + SPI_TX_DATA_REG);
+ }
+
+ mtk_spi_enable_transfer(master);
+
return IRQ_HANDLED;
}
if (num_gpios > 0) {
int i;
- hw->gpios = kzalloc(sizeof(int) * num_gpios, GFP_KERNEL);
+ hw->gpios = kcalloc(num_gpios, sizeof(*hw->gpios), GFP_KERNEL);
if (!hw->gpios) {
ret = -ENOMEM;
goto free_master;
/* Real CS - set the initial state. */
ret = gpio_request(gpio, np->name);
if (ret < 0) {
- dev_err(dev, "can't request gpio "
- "#%d: %d\n", i, ret);
+ dev_err(dev,
+ "can't request gpio #%d: %d\n",
+ i, ret);
goto free_gpios;
}
static struct dw_dma_slave byt_tx_param = { .dst_id = 0 };
static struct dw_dma_slave byt_rx_param = { .src_id = 1 };
+static struct dw_dma_slave mrfld3_tx_param = { .dst_id = 15 };
+static struct dw_dma_slave mrfld3_rx_param = { .src_id = 14 };
+static struct dw_dma_slave mrfld5_tx_param = { .dst_id = 13 };
+static struct dw_dma_slave mrfld5_rx_param = { .src_id = 12 };
+static struct dw_dma_slave mrfld6_tx_param = { .dst_id = 11 };
+static struct dw_dma_slave mrfld6_rx_param = { .src_id = 10 };
+
static struct dw_dma_slave bsw0_tx_param = { .dst_id = 0 };
static struct dw_dma_slave bsw0_rx_param = { .src_id = 1 };
static struct dw_dma_slave bsw1_tx_param = { .dst_id = 6 };
static int mrfld_spi_setup(struct pci_dev *dev, struct pxa_spi_info *c)
{
+ struct pci_dev *dma_dev = pci_get_slot(dev->bus, PCI_DEVFN(21, 0));
+ struct dw_dma_slave *tx, *rx;
+
switch (PCI_FUNC(dev->devfn)) {
case 0:
c->port_id = 3;
c->num_chipselect = 1;
+ c->tx_param = &mrfld3_tx_param;
+ c->rx_param = &mrfld3_rx_param;
break;
case 1:
c->port_id = 5;
c->num_chipselect = 4;
+ c->tx_param = &mrfld5_tx_param;
+ c->rx_param = &mrfld5_rx_param;
break;
case 2:
c->port_id = 6;
c->num_chipselect = 1;
+ c->tx_param = &mrfld6_tx_param;
+ c->rx_param = &mrfld6_rx_param;
break;
default:
return -ENODEV;
}
+
+ tx = c->tx_param;
+ tx->dma_dev = &dma_dev->dev;
+
+ rx = c->rx_param;
+ rx->dma_dev = &dma_dev->dev;
+
+ c->dma_filter = lpss_dma_filter;
return 0;
}
ssp = &spi_pdata.ssp;
ssp->phys_base = pci_resource_start(dev, 0);
ssp->mmio_base = pcim_iomap_table(dev)[0];
- ssp->irq = dev->irq;
ssp->port_id = (c->port_id >= 0) ? c->port_id : dev->devfn;
ssp->type = c->type;
+ pci_set_master(dev);
+
+ ret = pci_alloc_irq_vectors(dev, 1, 1, PCI_IRQ_ALL_TYPES);
+ if (ret < 0)
+ return ret;
+ ssp->irq = pci_irq_vector(dev, 0);
+
snprintf(buf, sizeof(buf), "pxa2xx-spi.%d", ssp->port_id);
ssp->clk = clk_register_fixed_rate(&dev->dev, buf , NULL, 0,
c->max_clk_rate);
return IRQ_HANDLED;
}
+static void handle_bad_msg(struct driver_data *drv_data)
+{
+ pxa2xx_spi_write(drv_data, SSCR0,
+ pxa2xx_spi_read(drv_data, SSCR0) & ~SSCR0_SSE);
+ pxa2xx_spi_write(drv_data, SSCR1,
+ pxa2xx_spi_read(drv_data, SSCR1) & ~drv_data->int_cr1);
+ if (!pxa25x_ssp_comp(drv_data))
+ pxa2xx_spi_write(drv_data, SSTO, 0);
+ write_SSSR_CS(drv_data, drv_data->clear_sr);
+
+ dev_err(&drv_data->pdev->dev,
+ "bad message state in interrupt handler\n");
+}
+
static irqreturn_t ssp_int(int irq, void *dev_id)
{
struct driver_data *drv_data = dev_id;
if (!(status & mask))
return IRQ_NONE;
- if (!drv_data->master->cur_msg) {
-
- pxa2xx_spi_write(drv_data, SSCR0,
- pxa2xx_spi_read(drv_data, SSCR0)
- & ~SSCR0_SSE);
- pxa2xx_spi_write(drv_data, SSCR1,
- pxa2xx_spi_read(drv_data, SSCR1)
- & ~drv_data->int_cr1);
- if (!pxa25x_ssp_comp(drv_data))
- pxa2xx_spi_write(drv_data, SSTO, 0);
- write_SSSR_CS(drv_data, drv_data->clear_sr);
-
- dev_err(&drv_data->pdev->dev,
- "bad message state in interrupt handler\n");
+ pxa2xx_spi_write(drv_data, SSCR1, sccr1_reg & ~drv_data->int_cr1);
+ pxa2xx_spi_write(drv_data, SSCR1, sccr1_reg);
+ if (!drv_data->master->cur_msg) {
+ handle_bad_msg(drv_data);
/* Never fail */
return IRQ_HANDLED;
}
{ PCI_VDEVICE(INTEL, 0x1ac2), LPSS_BXT_SSP },
{ PCI_VDEVICE(INTEL, 0x1ac4), LPSS_BXT_SSP },
{ PCI_VDEVICE(INTEL, 0x1ac6), LPSS_BXT_SSP },
+ /* GLK */
+ { PCI_VDEVICE(INTEL, 0x31c2), LPSS_BXT_SSP },
+ { PCI_VDEVICE(INTEL, 0x31c4), LPSS_BXT_SSP },
+ { PCI_VDEVICE(INTEL, 0x31c6), LPSS_BXT_SSP },
/* APL */
{ PCI_VDEVICE(INTEL, 0x5ac2), LPSS_BXT_SSP },
{ PCI_VDEVICE(INTEL, 0x5ac4), LPSS_BXT_SSP },
pxa2xx_spi_write(drv_data, SSCR1, tmp);
tmp = SSCR0_SCR(2) | SSCR0_Motorola | SSCR0_DataSize(8);
pxa2xx_spi_write(drv_data, SSCR0, tmp);
+ break;
default:
tmp = SSCR1_RxTresh(RX_THRESH_DFLT) |
SSCR1_TxTresh(TX_THRESH_DFLT);
for (i = 0; i < len; i++)
rspi_write_data(rspi, *tx++);
} else {
- ret = rspi_pio_transfer(rspi, tx, NULL, n);
+ ret = rspi_pio_transfer(rspi, tx, NULL, len);
if (ret < 0)
return ret;
}
for (i = 0; i < len; i++)
*rx++ = rspi_read_data(rspi);
} else {
- ret = rspi_pio_transfer(rspi, NULL, rx, n);
+ ret = rspi_pio_transfer(rspi, NULL, rx, len);
if (ret < 0)
return ret;
- *rx++ = ret;
}
n -= len;
}
sci->num_cs = temp;
}
- sci->no_cs = of_property_read_bool(dev->of_node, "broken-cs");
+ sci->no_cs = of_property_read_bool(dev->of_node, "no-cs-readback");
return sci;
}
};
static const struct of_device_id sh_msiof_match[] = {
- { .compatible = "renesas,sh-msiof", .data = &sh_data },
{ .compatible = "renesas,sh-mobile-msiof", .data = &sh_data },
{ .compatible = "renesas,msiof-r8a7790", .data = &r8a779x_data },
{ .compatible = "renesas,msiof-r8a7791", .data = &r8a779x_data },
{ .compatible = "renesas,msiof-r8a7792", .data = &r8a779x_data },
{ .compatible = "renesas,msiof-r8a7793", .data = &r8a779x_data },
{ .compatible = "renesas,msiof-r8a7794", .data = &r8a779x_data },
+ { .compatible = "renesas,rcar-gen2-msiof", .data = &r8a779x_data },
{ .compatible = "renesas,msiof-r8a7796", .data = &r8a779x_data },
+ { .compatible = "renesas,rcar-gen3-msiof", .data = &r8a779x_data },
+ { .compatible = "renesas,sh-msiof", .data = &sh_data }, /* Deprecated */
{},
};
MODULE_DEVICE_TABLE(of, sh_msiof_match);
if (!spi)
return;
- if (spi->dev.of_node)
+ if (spi->dev.of_node) {
of_node_clear_flag(spi->dev.of_node, OF_POPULATED);
+ of_node_put(spi->dev.of_node);
+ }
if (ACPI_COMPANION(&spi->dev))
acpi_device_clear_enumerated(ACPI_COMPANION(&spi->dev));
device_unregister(&spi->dev);
if (!n)
return -EINVAL;
- bi = kzalloc(n * sizeof(*bi), GFP_KERNEL);
+ bi = kcalloc(n, sizeof(*bi), GFP_KERNEL);
if (!bi)
return -ENOMEM;
if (master->dma_tx)
tx_dev = master->dma_tx->device->dev;
else
- tx_dev = &master->dev;
+ tx_dev = master->dev.parent;
if (master->dma_rx)
rx_dev = master->dma_rx->device->dev;
else
- rx_dev = &master->dev;
+ rx_dev = master->dev.parent;
list_for_each_entry(xfer, &msg->transfers, transfer_list) {
if (!master->can_dma(master, msg->spi, xfer))
if (master->dma_tx)
tx_dev = master->dma_tx->device->dev;
else
- tx_dev = &master->dev;
+ tx_dev = master->dev.parent;
if (master->dma_rx)
rx_dev = master->dma_rx->device->dev;
else
- rx_dev = &master->dev;
+ rx_dev = master->dev.parent;
list_for_each_entry(xfer, &msg->transfers, transfer_list) {
if (!master->can_dma(master, msg->spi, xfer))
if (rc) {
dev_err(&master->dev, "spi_device register error %s\n",
nc->full_name);
- goto err_out;
+ goto err_of_node_put;
}
return spi;
+err_of_node_put:
+ of_node_put(nc);
err_out:
spi_dev_put(spi);
return ERR_PTR(rc);
/**
* struct ep93xx_spi_info - EP93xx specific SPI descriptor
- * @num_chipselect: number of chip selects on this board, must be
- * at least one
+ * @chipselect: array of gpio numbers to use as chip selects
+ * @num_chipselect: ARRAY_SIZE(chipselect)
* @use_dma: use DMA for the transfers
*/
struct ep93xx_spi_info {
+ int *chipselect;
int num_chipselect;
bool use_dma;
};
-/**
- * struct ep93xx_spi_chip_ops - operation callbacks for SPI slave device
- * @setup: setup the chip select mechanism
- * @cleanup: cleanup the chip select mechanism
- * @cs_control: control the device chip select
- */
-struct ep93xx_spi_chip_ops {
- int (*setup)(struct spi_device *spi);
- void (*cleanup)(struct spi_device *spi);
- void (*cs_control)(struct spi_device *spi, int value);
-};
-
#endif /* __ASM_MACH_EP93XX_SPI_H */
#define SSSR_RFL_MASK (0xf << 12) /* Receive FIFO Level mask */
#define SSCR1_TFT (0x000003c0) /* Transmit FIFO Threshold (mask) */
-#define SSCR1_TxTresh(x) (((x) - 1) << 6) /* level [1..16] */
+#define SSCR1_TxTresh(x) (((x) - 1) << 6) /* level [1..16] */
#define SSCR1_RFT (0x00003c00) /* Receive FIFO Threshold (mask) */
-#define SSCR1_RxTresh(x) (((x) - 1) << 10) /* level [1..16] */
+#define SSCR1_RxTresh(x) (((x) - 1) << 10) /* level [1..16] */
#define RX_THRESH_CE4100_DFLT 2
#define TX_THRESH_CE4100_DFLT 2
#define CE4100_SSCR1_RxTresh(x) (((x) - 1) << 10) /* level [1..4] */
/* QUARK_X1000 SSCR0 bit definition */
-#define QUARK_X1000_SSCR0_DSS (0x1F) /* Data Size Select (mask) */
-#define QUARK_X1000_SSCR0_DataSize(x) ((x) - 1) /* Data Size Select [4..32] */
-#define QUARK_X1000_SSCR0_FRF (0x3 << 5) /* FRame Format (mask) */
+#define QUARK_X1000_SSCR0_DSS (0x1F << 0) /* Data Size Select (mask) */
+#define QUARK_X1000_SSCR0_DataSize(x) ((x) - 1) /* Data Size Select [4..32] */
+#define QUARK_X1000_SSCR0_FRF (0x3 << 5) /* FRame Format (mask) */
#define QUARK_X1000_SSCR0_Motorola (0x0 << 5) /* Motorola's Serial Peripheral Interface (SPI) */
#define RX_THRESH_QUARK_X1000_DFLT 1
#define QUARK_X1000_SSCR1_TxTresh(x) (((x) - 1) << 6) /* level [1..32] */
#define QUARK_X1000_SSCR1_RFT (0x1F << 11) /* Receive FIFO Threshold (mask) */
#define QUARK_X1000_SSCR1_RxTresh(x) (((x) - 1) << 11) /* level [1..32] */
-#define QUARK_X1000_SSCR1_STRF (1 << 17) /* Select FIFO or EFWR */
-#define QUARK_X1000_SSCR1_EFWR (1 << 16) /* Enable FIFO Write/Read */
+#define QUARK_X1000_SSCR1_STRF (1 << 17) /* Select FIFO or EFWR */
+#define QUARK_X1000_SSCR1_EFWR (1 << 16) /* Enable FIFO Write/Read */
/* extra bits in PXA255, PXA26x and PXA27x SSP ports */
#define SSCR0_TISSP (1 << 4) /* TI Sync Serial Protocol */
git.samba.org / sfrench / cifs-2.6.git / commitdiff