*
* Hardware documentation available at http://developer.intel.com/
*
+ * Documentation
+ * Publically available from Intel web site. Errata documentation
+ * is also publically available. As an aide to anyone hacking on this
+ * driver the list of errata that are relevant is below.going back to
+ * PIIX4. Older device documentation is now a bit tricky to find.
+ *
+ * The chipsets all follow very much the same design. The orginal Triton
+ * series chipsets do _not_ support independant device timings, but this
+ * is fixed in Triton II. With the odd mobile exception the chips then
+ * change little except in gaining more modes until SATA arrives. This
+ * driver supports only the chips with independant timing (that is those
+ * with SITRE and the 0x44 timing register). See pata_oldpiix and pata_mpiix
+ * for the early chip drivers.
+ *
+ * Errata of note:
+ *
+ * Unfixable
+ * PIIX4 errata #9 - Only on ultra obscure hw
+ * ICH3 errata #13 - Not observed to affect real hw
+ * by Intel
+ *
+ * Things we must deal with
+ * PIIX4 errata #10 - BM IDE hang with non UDMA
+ * (must stop/start dma to recover)
+ * 440MX errata #15 - As PIIX4 errata #10
+ * PIIX4 errata #15 - Must not read control registers
+ * during a PIO transfer
+ * 440MX errata #13 - As PIIX4 errata #15
+ * ICH2 errata #21 - DMA mode 0 doesn't work right
+ * ICH0/1 errata #55 - As ICH2 errata #21
+ * ICH2 spec c #9 - Extra operations needed to handle
+ * drive hotswap [NOT YET SUPPORTED]
+ * ICH2 spec c #20 - IDE PRD must not cross a 64K boundary
+ * and must be dword aligned
+ * ICH2 spec c #24 - UDMA mode 4,5 t85/86 should be 6ns not 3.3
+ *
+ * Should have been BIOS fixed:
+ * 450NX: errata #19 - DMA hangs on old 450NX
+ * 450NX: errata #20 - DMA hangs on old 450NX
+ * 450NX: errata #25 - Corruption with DMA on old 450NX
+ * ICH3 errata #15 - IDE deadlock under high load
+ * (BIOS must set dev 31 fn 0 bit 23)
+ * ICH3 errata #18 - Don't use native mode
*/
#include <linux/kernel.h>
ICH5_PCS = 0x92, /* port control and status */
PIIX_SCC = 0x0A, /* sub-class code register */
- PIIX_FLAG_AHCI = (1 << 28), /* AHCI possible */
- PIIX_FLAG_CHECKINTR = (1 << 29), /* make sure PCI INTx enabled */
- PIIX_FLAG_COMBINED = (1 << 30), /* combined mode possible */
+ PIIX_FLAG_AHCI = (1 << 27), /* AHCI possible */
+ PIIX_FLAG_CHECKINTR = (1 << 28), /* make sure PCI INTx enabled */
+ PIIX_FLAG_COMBINED = (1 << 29), /* combined mode possible */
+ /* ICH6/7 use different scheme for map value */
+ PIIX_FLAG_COMBINED_ICH6 = PIIX_FLAG_COMBINED | (1 << 30),
/* combined mode. if set, PATA is channel 0.
* if clear, PATA is channel 1.
ich5_sata = 1,
piix4_pata = 2,
ich6_sata = 3,
- ich6_sata_rm = 4,
- ich7_sata = 5,
- esb2_sata = 6,
+ ich6_sata_ahci = 4,
PIIX_AHCI_DEVICE = 6,
};
static int piix_init_one (struct pci_dev *pdev,
const struct pci_device_id *ent);
-static void piix_pata_phy_reset(struct ata_port *ap);
-static void piix_sata_phy_reset(struct ata_port *ap);
+static int piix_pata_probe_reset(struct ata_port *ap, unsigned int *classes);
+static int piix_sata_probe_reset(struct ata_port *ap, unsigned int *classes);
static void piix_set_piomode (struct ata_port *ap, struct ata_device *adev);
static void piix_set_dmamode (struct ata_port *ap, struct ata_device *adev);
{ 0x8086, 0x25a3, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_sata },
{ 0x8086, 0x25b0, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich5_sata },
{ 0x8086, 0x2651, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata },
- { 0x8086, 0x2652, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata_rm },
- { 0x8086, 0x2653, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata_rm },
- { 0x8086, 0x27c0, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich7_sata },
- { 0x8086, 0x27c4, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich7_sata },
- { 0x8086, 0x2680, PCI_ANY_ID, PCI_ANY_ID, 0, 0, esb2_sata },
+ { 0x8086, 0x2652, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata_ahci },
+ { 0x8086, 0x2653, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata_ahci },
+ { 0x8086, 0x27c0, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata_ahci },
+ { 0x8086, 0x27c4, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata_ahci },
+ { 0x8086, 0x2680, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata_ahci },
+ { 0x8086, 0x2820, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata_ahci },
+ { 0x8086, 0x2825, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata_ahci },
+ { 0x8086, 0x2828, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata_ahci },
{ } /* terminate list */
};
.id_table = piix_pci_tbl,
.probe = piix_init_one,
.remove = ata_pci_remove_one,
+ .suspend = ata_pci_device_suspend,
+ .resume = ata_pci_device_resume,
};
static struct scsi_host_template piix_sht = {
.name = DRV_NAME,
.ioctl = ata_scsi_ioctl,
.queuecommand = ata_scsi_queuecmd,
+ .eh_timed_out = ata_scsi_timed_out,
.eh_strategy_handler = ata_scsi_error,
.can_queue = ATA_DEF_QUEUE,
.this_id = ATA_SHT_THIS_ID,
.sg_tablesize = LIBATA_MAX_PRD,
- .max_sectors = ATA_MAX_SECTORS,
.cmd_per_lun = ATA_SHT_CMD_PER_LUN,
.emulated = ATA_SHT_EMULATED,
.use_clustering = ATA_SHT_USE_CLUSTERING,
.dma_boundary = ATA_DMA_BOUNDARY,
.slave_configure = ata_scsi_slave_config,
.bios_param = ata_std_bios_param,
- .ordered_flush = 1,
+ .resume = ata_scsi_device_resume,
+ .suspend = ata_scsi_device_suspend,
};
static const struct ata_port_operations piix_pata_ops = {
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
- .phy_reset = piix_pata_phy_reset,
+ .probe_reset = piix_pata_probe_reset,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
- .phy_reset = piix_sata_phy_reset,
+ .probe_reset = piix_sata_probe_reset,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
/* ich5_pata */
{
.sht = &piix_sht,
- .host_flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST |
- PIIX_FLAG_CHECKINTR,
+ .host_flags = ATA_FLAG_SLAVE_POSS | PIIX_FLAG_CHECKINTR,
.pio_mask = 0x1f, /* pio0-4 */
#if 0
.mwdma_mask = 0x06, /* mwdma1-2 */
/* ich5_sata */
{
.sht = &piix_sht,
- .host_flags = ATA_FLAG_SATA | ATA_FLAG_SRST |
- PIIX_FLAG_COMBINED | PIIX_FLAG_CHECKINTR,
+ .host_flags = ATA_FLAG_SATA | PIIX_FLAG_COMBINED |
+ PIIX_FLAG_CHECKINTR,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
.udma_mask = 0x7f, /* udma0-6 */
/* piix4_pata */
{
.sht = &piix_sht,
- .host_flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .host_flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f, /* pio0-4 */
#if 0
.mwdma_mask = 0x06, /* mwdma1-2 */
/* ich6_sata */
{
.sht = &piix_sht,
- .host_flags = ATA_FLAG_SATA | ATA_FLAG_SRST |
- PIIX_FLAG_COMBINED | PIIX_FLAG_CHECKINTR |
- ATA_FLAG_SLAVE_POSS,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = 0x7f, /* udma0-6 */
- .port_ops = &piix_sata_ops,
- },
-
- /* ich6_sata_rm */
- {
- .sht = &piix_sht,
- .host_flags = ATA_FLAG_SATA | ATA_FLAG_SRST |
- PIIX_FLAG_COMBINED | PIIX_FLAG_CHECKINTR |
- ATA_FLAG_SLAVE_POSS | PIIX_FLAG_AHCI,
+ .host_flags = ATA_FLAG_SATA | PIIX_FLAG_COMBINED_ICH6 |
+ PIIX_FLAG_CHECKINTR | ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
.udma_mask = 0x7f, /* udma0-6 */
.port_ops = &piix_sata_ops,
},
- /* ich7_sata */
+ /* ich6_sata_ahci */
{
.sht = &piix_sht,
- .host_flags = ATA_FLAG_SATA | ATA_FLAG_SRST |
- PIIX_FLAG_COMBINED | PIIX_FLAG_CHECKINTR |
- ATA_FLAG_SLAVE_POSS | PIIX_FLAG_AHCI,
- .pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x07, /* mwdma0-2 */
- .udma_mask = 0x7f, /* udma0-6 */
- .port_ops = &piix_sata_ops,
- },
-
- /* esb2_sata */
- {
- .sht = &piix_sht,
- .host_flags = ATA_FLAG_SATA | ATA_FLAG_SRST |
- PIIX_FLAG_COMBINED | PIIX_FLAG_CHECKINTR |
- ATA_FLAG_SLAVE_POSS | PIIX_FLAG_AHCI,
+ .host_flags = ATA_FLAG_SATA | PIIX_FLAG_COMBINED_ICH6 |
+ PIIX_FLAG_CHECKINTR | ATA_FLAG_SLAVE_POSS |
+ PIIX_FLAG_AHCI,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
.udma_mask = 0x7f, /* udma0-6 */
}
/**
- * piix_pata_phy_reset - Probe specified port on PATA host controller
- * @ap: Port to probe
+ * piix_pata_probeinit - probeinit for PATA host controller
+ * @ap: Target port
*
- * Probe PATA phy.
+ * Probeinit including cable detection.
*
* LOCKING:
* None (inherited from caller).
*/
+static void piix_pata_probeinit(struct ata_port *ap)
+{
+ piix_pata_cbl_detect(ap);
+ ata_std_probeinit(ap);
+}
-static void piix_pata_phy_reset(struct ata_port *ap)
+/**
+ * piix_pata_probe_reset - Perform reset on PATA port and classify
+ * @ap: Port to reset
+ * @classes: Resulting classes of attached devices
+ *
+ * Reset PATA phy and classify attached devices.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+static int piix_pata_probe_reset(struct ata_port *ap, unsigned int *classes)
{
struct pci_dev *pdev = to_pci_dev(ap->host_set->dev);
if (!pci_test_config_bits(pdev, &piix_enable_bits[ap->hard_port_no])) {
- ata_port_disable(ap);
printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id);
- return;
+ return 0;
}
- piix_pata_cbl_detect(ap);
-
- ata_port_probe(ap);
-
- ata_bus_reset(ap);
+ return ata_drive_probe_reset(ap, piix_pata_probeinit,
+ ata_std_softreset, NULL,
+ ata_std_postreset, classes);
}
/**
int orig_mask, mask, i;
u8 pcs;
- mask = (PIIX_PORT_PRESENT << ap->hard_port_no) |
- (PIIX_PORT_ENABLED << ap->hard_port_no);
-
pci_read_config_byte(pdev, ICH5_PCS, &pcs);
orig_mask = (int) pcs & 0xff;
}
/**
- * piix_sata_phy_reset - Probe specified port on SATA host controller
- * @ap: Port to probe
+ * piix_sata_probe_reset - Perform reset on SATA port and classify
+ * @ap: Port to reset
+ * @classes: Resulting classes of attached devices
*
- * Probe SATA phy.
+ * Reset SATA phy and classify attached devices.
*
* LOCKING:
* None (inherited from caller).
*/
-
-static void piix_sata_phy_reset(struct ata_port *ap)
+static int piix_sata_probe_reset(struct ata_port *ap, unsigned int *classes)
{
if (!piix_sata_probe(ap)) {
- ata_port_disable(ap);
printk(KERN_INFO "ata%u: SATA port has no device.\n", ap->id);
- return;
+ return 0;
}
- ap->cbl = ATA_CBL_SATA;
-
- ata_port_probe(ap);
-
- ata_bus_reset(ap);
+ return ata_drive_probe_reset(ap, ata_std_probeinit,
+ ata_std_softreset, NULL,
+ ata_std_postreset, classes);
}
/**
return rc;
}
+/**
+ * piix_check_450nx_errata - Check for problem 450NX setup
+ * @ata_dev: the PCI device to check
+ *
+ * Check for the present of 450NX errata #19 and errata #25. If
+ * they are found return an error code so we can turn off DMA
+ */
+
+static int __devinit piix_check_450nx_errata(struct pci_dev *ata_dev)
+{
+ struct pci_dev *pdev = NULL;
+ u16 cfg;
+ u8 rev;
+ int no_piix_dma = 0;
+
+ while((pdev = pci_get_device(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82454NX, pdev)) != NULL)
+ {
+ /* Look for 450NX PXB. Check for problem configurations
+ A PCI quirk checks bit 6 already */
+ pci_read_config_byte(pdev, PCI_REVISION_ID, &rev);
+ pci_read_config_word(pdev, 0x41, &cfg);
+ /* Only on the original revision: IDE DMA can hang */
+ if(rev == 0x00)
+ no_piix_dma = 1;
+ /* On all revisions below 5 PXB bus lock must be disabled for IDE */
+ else if(cfg & (1<<14) && rev < 5)
+ no_piix_dma = 2;
+ }
+ if(no_piix_dma)
+ dev_printk(KERN_WARNING, &ata_dev->dev, "450NX errata present, disabling IDE DMA.\n");
+ if(no_piix_dma == 2)
+ dev_printk(KERN_WARNING, &ata_dev->dev, "A BIOS update may resolve this.\n");
+ return no_piix_dma;
+}
+
/**
* piix_init_one - Register PIIX ATA PCI device with kernel services
* @pdev: PCI device to register
struct ata_port_info *port_info[2];
unsigned int combined = 0;
unsigned int pata_chan = 0, sata_chan = 0;
+ unsigned long host_flags;
if (!printed_version++)
dev_printk(KERN_DEBUG, &pdev->dev,
port_info[0] = &piix_port_info[ent->driver_data];
port_info[1] = &piix_port_info[ent->driver_data];
- if (port_info[0]->host_flags & PIIX_FLAG_AHCI) {
+ host_flags = port_info[0]->host_flags;
+
+ if (host_flags & PIIX_FLAG_AHCI) {
u8 tmp;
pci_read_config_byte(pdev, PIIX_SCC, &tmp);
if (tmp == PIIX_AHCI_DEVICE) {
}
}
- if (port_info[0]->host_flags & PIIX_FLAG_COMBINED) {
+ if (host_flags & PIIX_FLAG_COMBINED) {
u8 tmp;
pci_read_config_byte(pdev, ICH5_PMR, &tmp);
- if (tmp & PIIX_COMB) {
- combined = 1;
- if (tmp & PIIX_COMB_PATA_P0)
+ if (host_flags & PIIX_FLAG_COMBINED_ICH6) {
+ switch (tmp & 0x3) {
+ case 0:
+ break;
+ case 1:
+ combined = 1;
sata_chan = 1;
- else
+ break;
+ case 2:
+ combined = 1;
pata_chan = 1;
+ break;
+ case 3:
+ dev_printk(KERN_WARNING, &pdev->dev,
+ "invalid MAP value %u\n", tmp);
+ break;
+ }
+ } else {
+ if (tmp & PIIX_COMB) {
+ combined = 1;
+ if (tmp & PIIX_COMB_PATA_P0)
+ sata_chan = 1;
+ else
+ pata_chan = 1;
+ }
}
}
* MSI is disabled (and it is disabled, as we don't use
* message-signalled interrupts currently).
*/
- if (port_info[0]->host_flags & PIIX_FLAG_CHECKINTR)
+ if (host_flags & PIIX_FLAG_CHECKINTR)
pci_intx(pdev, 1);
if (combined) {
"combined mode detected (p=%u, s=%u)\n",
pata_chan, sata_chan);
}
-
+ if (piix_check_450nx_errata(pdev)) {
+ /* This writes into the master table but it does not
+ really matter for this errata as we will apply it to
+ all the PIIX devices on the board */
+ port_info[0]->mwdma_mask = 0;
+ port_info[0]->udma_mask = 0;
+ port_info[1]->mwdma_mask = 0;
+ port_info[1]->udma_mask = 0;
+ }
return ata_pci_init_one(pdev, port_info, 2);
}
git.samba.org / sfrench / cifs-2.6.git / blobdiff