trivial: Kconfig: .ko is normally not included in module names

[sfrench/cifs-2.6.git] / drivers / s390 / net / Kconfig

diff --git a/drivers/s390/net/Kconfig b/drivers/s390/net/Kconfig
index a7745c82b4ae594a05ebbdc52b284e90ed4e844c..cb909a5b5047e11fc6b3d6ddcca3a31811f73106 100644 (file)
--- a/drivers/s390/net/Kconfig
+++ b/drivers/s390/net/Kconfig
@@ -8,7 +8,7 @@ config LCS
           Select this option if you want to use LCS networking on IBM System z.
           This device driver supports Token Ring (IEEE 802.5),
           FDDI (IEEE 802.7) and Ethernet.
-          To compile as a module, choose M. The module name is lcs.ko.
+          To compile as a module, choose M. The module name is lcs.
           If you do not know what it is, it's safe to choose Y.
 
 config CTCM
@@ -21,7 +21,7 @@ config CTCM
          It also supports virtual CTCs when running under VM.
          This driver also supports channel-to-channel MPC SNA devices.
          MPC is an SNA protocol device used by Communication Server for Linux.
-         To compile as a module, choose M. The module name is ctcm.ko.
+         To compile as a module, choose M. The module name is ctcm.
          To compile into the kernel, choose Y.
          If you do not need any channel-to-channel connection, choose N.
 
@@ -34,7 +34,7 @@ config NETIUCV
          link between VM guests. Using ifconfig a point-to-point connection
          can be established to the Linux on IBM System z
          running on the other VM guest. To compile as a module, choose M.
-         The module name is netiucv.ko. If unsure, choose Y.
+         The module name is netiucv. If unsure, choose Y.
 
 config SMSGIUCV
        tristate "IUCV special message support (VM only)"
@@ -50,7 +50,7 @@ config CLAW
          This driver supports channel attached CLAW devices.
          CLAW is Common Link Access for Workstation.  Common devices
           that use CLAW are RS/6000s, Cisco Routers (CIP) and 3172 devices.
-         To compile as a module, choose M. The module name is claw.ko.
+         To compile as a module, choose M. The module name is claw.
          To compile into the kernel, choose Y.
 
 config QETH
@@ -65,14 +65,14 @@ config QETH
          <http://www.ibm.com/developerworks/linux/linux390>
 
          To compile this driver as a module, choose M.
-         The module name is qeth.ko.
+         The module name is qeth.
 
 config QETH_L2
         tristate "qeth layer 2 device support"
         depends on QETH
         help
           Select this option to be able to run qeth devices in layer 2 mode.
-          To compile as a module, choose M. The module name is qeth_l2.ko.
+          To compile as a module, choose M. The module name is qeth_l2.
           If unsure, choose y.
 
 config QETH_L3
@@ -80,7 +80,7 @@ config QETH_L3
         depends on QETH
         help
           Select this option to be able to run qeth devices in layer 3 mode.
-          To compile as a module choose M. The module name is qeth_l3.ko.
+          To compile as a module choose M. The module name is qeth_l3.
           If unsure, choose Y.
 
 config QETH_IPV6