#include <linux/pci.h>
#include <linux/ioport.h>
#include <linux/slab.h>
-#include <linux/smp_lock.h>
#include <asm/byteorder.h>
#include <asm/pdc.h>
#include <asm/page.h>
#include <asm/system.h>
+#include <asm/ropes.h>
#include <asm/hardware.h> /* for register_parisc_driver() stuff */
#include <asm/parisc-device.h>
-#include <asm/iosapic.h> /* for iosapic_register() */
#include <asm/io.h> /* read/write stuff */
#undef DEBUG_LBA /* general stuff */
#define MODULE_NAME "LBA"
-#define LBA_FUNC_ID 0x0000 /* function id */
-#define LBA_FCLASS 0x0008 /* function class, bist, header, rev... */
-#define LBA_CAPABLE 0x0030 /* capabilities register */
-
-#define LBA_PCI_CFG_ADDR 0x0040 /* poke CFG address here */
-#define LBA_PCI_CFG_DATA 0x0048 /* read or write data here */
-
-#define LBA_PMC_MTLT 0x0050 /* Firmware sets this - read only. */
-#define LBA_FW_SCRATCH 0x0058 /* Firmware writes the PCI bus number here. */
-#define LBA_ERROR_ADDR 0x0070 /* On error, address gets logged here */
-
-#define LBA_ARB_MASK 0x0080 /* bit 0 enable arbitration. PAT/PDC enables */
-#define LBA_ARB_PRI 0x0088 /* firmware sets this. */
-#define LBA_ARB_MODE 0x0090 /* firmware sets this. */
-#define LBA_ARB_MTLT 0x0098 /* firmware sets this. */
-
-#define LBA_MOD_ID 0x0100 /* Module ID. PDC_PAT_CELL reports 4 */
-
-#define LBA_STAT_CTL 0x0108 /* Status & Control */
-#define LBA_BUS_RESET 0x01 /* Deassert PCI Bus Reset Signal */
-#define CLEAR_ERRLOG 0x10 /* "Clear Error Log" cmd */
-#define CLEAR_ERRLOG_ENABLE 0x20 /* "Clear Error Log" Enable */
-#define HF_ENABLE 0x40 /* enable HF mode (default is -1 mode) */
-
-#define LBA_LMMIO_BASE 0x0200 /* < 4GB I/O address range */
-#define LBA_LMMIO_MASK 0x0208
-
-#define LBA_GMMIO_BASE 0x0210 /* > 4GB I/O address range */
-#define LBA_GMMIO_MASK 0x0218
-
-#define LBA_WLMMIO_BASE 0x0220 /* All < 4GB ranges under the same *SBA* */
-#define LBA_WLMMIO_MASK 0x0228
-
-#define LBA_WGMMIO_BASE 0x0230 /* All > 4GB ranges under the same *SBA* */
-#define LBA_WGMMIO_MASK 0x0238
-
-#define LBA_IOS_BASE 0x0240 /* I/O port space for this LBA */
-#define LBA_IOS_MASK 0x0248
-
-#define LBA_ELMMIO_BASE 0x0250 /* Extra LMMIO range */
-#define LBA_ELMMIO_MASK 0x0258
-
-#define LBA_EIOS_BASE 0x0260 /* Extra I/O port space */
-#define LBA_EIOS_MASK 0x0268
-
-#define LBA_GLOBAL_MASK 0x0270 /* Mercury only: Global Address Mask */
-#define LBA_DMA_CTL 0x0278 /* firmware sets this */
-
-#define LBA_IBASE 0x0300 /* SBA DMA support */
-#define LBA_IMASK 0x0308
-
-/* FIXME: ignore DMA Hint stuff until we can measure performance */
-#define LBA_HINT_CFG 0x0310
-#define LBA_HINT_BASE 0x0380 /* 14 registers at every 8 bytes. */
-
-#define LBA_BUS_MODE 0x0620
-
-/* ERROR regs are needed for config cycle kluges */
-#define LBA_ERROR_CONFIG 0x0680
-#define LBA_SMART_MODE 0x20
-#define LBA_ERROR_STATUS 0x0688
-#define LBA_ROPE_CTL 0x06A0
-
-#define LBA_IOSAPIC_BASE 0x800 /* Offset of IRQ logic */
-
/* non-postable I/O port space, densely packed */
#define LBA_PORT_BASE (PCI_F_EXTEND | 0xfee00000UL)
static void __iomem *astro_iop_base __read_mostly;
-#define ELROY_HVERS 0x782
-#define MERCURY_HVERS 0x783
-#define QUICKSILVER_HVERS 0x784
-
-static inline int IS_ELROY(struct parisc_device *d)
-{
- return (d->id.hversion == ELROY_HVERS);
-}
-
-static inline int IS_MERCURY(struct parisc_device *d)
-{
- return (d->id.hversion == MERCURY_HVERS);
-}
-
-static inline int IS_QUICKSILVER(struct parisc_device *d)
-{
- return (d->id.hversion == QUICKSILVER_HVERS);
-}
-
-
-/*
-** lba_device: Per instance Elroy data structure
-*/
-struct lba_device {
- struct pci_hba_data hba;
-
- spinlock_t lba_lock;
- void *iosapic_obj;
-
-#ifdef CONFIG_64BIT
- void __iomem * iop_base; /* PA_VIEW - for IO port accessor funcs */
-#endif
-
- int flags; /* state/functionality enabled */
- int hw_rev; /* HW revision of chip */
-};
-
-
static u32 lba_t32;
/* lba flags */
printk(KERN_DEBUG "(%p)", r->parent);
for (i = d; i ; --i) printk(" ");
- printk(KERN_DEBUG "%p [%lx,%lx]/%lx\n", r, r->start, r->end, r->flags);
+ printk(KERN_DEBUG "%p [%lx,%lx]/%lx\n", r,
+ (long)r->start, (long)r->end, r->flags);
lba_dump_res(r->child, d+2);
lba_dump_res(r->sibling, d);
}
#ifdef CONFIG_64BIT
-/*
-** Determine if a device is already configured.
-** If so, reserve it resources.
-**
-** Read PCI cfg command register and see if I/O or MMIO is enabled.
-** PAT has to enable the devices it's using.
-**
-** Note: resources are fixed up before we try to claim them.
-*/
-static void
-lba_claim_dev_resources(struct pci_dev *dev)
-{
- u16 cmd;
- int i, srch_flags;
-
- (void) pci_read_config_word(dev, PCI_COMMAND, &cmd);
-
- srch_flags = (cmd & PCI_COMMAND_IO) ? IORESOURCE_IO : 0;
- if (cmd & PCI_COMMAND_MEMORY)
- srch_flags |= IORESOURCE_MEM;
-
- if (!srch_flags)
- return;
-
- for (i = 0; i <= PCI_ROM_RESOURCE; i++) {
- if (dev->resource[i].flags & srch_flags) {
- pci_claim_resource(dev, i);
- DBG(" claimed %s %d [%lx,%lx]/%lx\n",
- pci_name(dev), i,
- dev->resource[i].start,
- dev->resource[i].end,
- dev->resource[i].flags
- );
- }
- }
-}
-
-
/*
* truncate_pat_collision: Deal with overlaps or outright collisions
* between PAT PDC reported ranges.
printk(KERN_WARNING "LBA: Truncating lmmio_space [%lx/%lx] "
"to [%lx,%lx]\n",
start, end,
- new->start, new->end );
+ (long)new->start, (long)new->end );
return 0; /* truncation successful */
}
#else
-#define lba_claim_dev_resources(dev) do { } while (0)
#define truncate_pat_collision(r,n) (0)
#endif
** pci_alloc_primary_bus() mangles this.
*/
if (bus->self) {
+ int i;
/* PCI-PCI Bridge */
pci_read_bridge_bases(bus);
+ for (i = PCI_BRIDGE_RESOURCES; i < PCI_NUM_RESOURCES; i++) {
+ pci_claim_resource(bus->self, i);
+ }
} else {
/* Host-PCI Bridge */
int err, i;
printk("FAILED: lba_fixup_bus() request for "
"elmmio_space [%lx/%lx]\n",
- ldev->hba.elmmio_space.start,
- ldev->hba.elmmio_space.end);
+ (long)ldev->hba.elmmio_space.start,
+ (long)ldev->hba.elmmio_space.end);
/* lba_dump_res(&iomem_resource, 2); */
/* BUG(); */
&(ldev->hba.lmmio_space))) {
printk(KERN_WARNING "LBA: lmmio_space [%lx/%lx] duplicate!\n",
- ldev->hba.lmmio_space.start,
- ldev->hba.lmmio_space.end);
+ (long)ldev->hba.lmmio_space.start,
+ (long)ldev->hba.lmmio_space.end);
} else {
err = request_resource(&iomem_resource, &(ldev->hba.lmmio_space));
if (err < 0) {
printk(KERN_ERR "FAILED: lba_fixup_bus() request for "
"lmmio_space [%lx/%lx]\n",
- ldev->hba.lmmio_space.start,
- ldev->hba.lmmio_space.end);
+ (long)ldev->hba.lmmio_space.start,
+ (long)ldev->hba.lmmio_space.end);
} else
bus->resource[i++] = &(ldev->hba.lmmio_space);
}
if (err < 0) {
printk("FAILED: lba_fixup_bus() request for "
"gmmio_space [%lx/%lx]\n",
- ldev->hba.gmmio_space.start,
- ldev->hba.gmmio_space.end);
+ (long)ldev->hba.gmmio_space.start,
+ (long)ldev->hba.gmmio_space.end);
lba_dump_res(&iomem_resource, 2);
BUG();
}
DBG("lba_fixup_bus() WTF? 0x%lx [%lx/%lx] XXX",
res->flags, res->start, res->end);
}
+ if ((i != PCI_ROM_RESOURCE) ||
+ (res->flags & IORESOURCE_ROM_ENABLE))
+ pci_claim_resource(dev, i);
}
#ifdef FBB_SUPPORT
bus->bridge_ctl &= ~(status & PCI_STATUS_FAST_BACK);
#endif
- if (is_pdc_pat()) {
- /* Claim resources for PDC's devices */
- lba_claim_dev_resources(dev);
- }
-
/*
** P2PB's have no IRQs. ignore them.
*/
#define LBA_PORT_OUT(size, mask) \
static void lba_pat_out##size (struct pci_hba_data *l, u16 addr, u##size val) \
{ \
- void *where = (void *) PIOP_TO_GMMIO(LBA_DEV(l), addr); \
+ void __iomem *where = PIOP_TO_GMMIO(LBA_DEV(l), addr); \
DBG_PORT("%s(0x%p, 0x%x, 0x%x)\n", __FUNCTION__, l, addr, val); \
WRITE_REG##size(val, where); \
/* flush the I/O down to the elroy at least */ \
/* used to fix up pre-initialized MEM BARs */
if (!lba_dev->hba.lmmio_space.start) {
sprintf(lba_dev->hba.lmmio_name,
- "PCI%02lx LMMIO",
- lba_dev->hba.bus_num.start);
+ "PCI%02x LMMIO",
+ (int)lba_dev->hba.bus_num.start);
lba_dev->hba.lmmio_space_offset = p->start -
io->start;
r = &lba_dev->hba.lmmio_space;
r->name = lba_dev->hba.lmmio_name;
} else if (!lba_dev->hba.elmmio_space.start) {
sprintf(lba_dev->hba.elmmio_name,
- "PCI%02lx ELMMIO",
- lba_dev->hba.bus_num.start);
+ "PCI%02x ELMMIO",
+ (int)lba_dev->hba.bus_num.start);
r = &lba_dev->hba.elmmio_space;
r->name = lba_dev->hba.elmmio_name;
} else {
case PAT_GMMIO:
/* MMIO space > 4GB phys addr; for 64-bit BAR */
- sprintf(lba_dev->hba.gmmio_name, "PCI%02lx GMMIO",
- lba_dev->hba.bus_num.start);
+ sprintf(lba_dev->hba.gmmio_name, "PCI%02x GMMIO",
+ (int)lba_dev->hba.bus_num.start);
r = &lba_dev->hba.gmmio_space;
r->name = lba_dev->hba.gmmio_name;
r->start = p->start;
*/
lba_dev->iop_base = ioremap_nocache(p->start, 64 * 1024 * 1024);
- sprintf(lba_dev->hba.io_name, "PCI%02lx Ports",
- lba_dev->hba.bus_num.start);
+ sprintf(lba_dev->hba.io_name, "PCI%02x Ports",
+ (int)lba_dev->hba.bus_num.start);
r = &lba_dev->hba.io_space;
r->name = lba_dev->hba.io_name;
r->start = HBA_PORT_BASE(lba_dev->hba.hba_num);
** Legacy boxes but it's nice to see in /proc/iomem.
*/
r = &(lba_dev->hba.lmmio_space);
- sprintf(lba_dev->hba.lmmio_name, "PCI%02lx LMMIO",
- lba_dev->hba.bus_num.start);
+ sprintf(lba_dev->hba.lmmio_name, "PCI%02x LMMIO",
+ (int)lba_dev->hba.bus_num.start);
r->name = lba_dev->hba.lmmio_name;
#if 1
** an existing (but unused portion of) distributed range.
*/
r = &(lba_dev->hba.elmmio_space);
- sprintf(lba_dev->hba.elmmio_name, "PCI%02lx ELMMIO",
- lba_dev->hba.bus_num.start);
+ sprintf(lba_dev->hba.elmmio_name, "PCI%02x ELMMIO",
+ (int)lba_dev->hba.bus_num.start);
r->name = lba_dev->hba.elmmio_name;
#if 1
#endif
r = &(lba_dev->hba.io_space);
- sprintf(lba_dev->hba.io_name, "PCI%02lx Ports",
- lba_dev->hba.bus_num.start);
+ sprintf(lba_dev->hba.io_name, "PCI%02x Ports",
+ (int)lba_dev->hba.bus_num.start);
r->name = lba_dev->hba.io_name;
r->flags = IORESOURCE_IO;
r->start = READ_REG32(lba_dev->hba.base_addr + LBA_IOS_BASE) & ~1L;
return 0;
}
-
+/*
+ * Unfortunately, when firmware numbers busses, it doesn't take into account
+ * Cardbus bridges. So we have to renumber the busses to suit ourselves.
+ * Elroy/Mercury don't actually know what bus number they're attached to;
+ * we use bus 0 to indicate the directly attached bus and any other bus
+ * number will be taken care of by the PCI-PCI bridge.
+ */
+static unsigned int lba_next_bus = 0;
/*
-** Determine if lba should claim this chip (return 0) or not (return 1).
-** If so, initialize the chip and tell other partners in crime they
-** have work to do.
-*/
+ * Determine if lba should claim this chip (return 0) or not (return 1).
+ * If so, initialize the chip and tell other partners in crime they
+ * have work to do.
+ */
static int __init
lba_driver_probe(struct parisc_device *dev)
{
default: version = "TR4+";
}
- printk(KERN_INFO "%s version %s (0x%x) found at 0x%lx\n",
- MODULE_NAME, version, func_class & 0xf, dev->hpa.start);
+ printk(KERN_INFO "Elroy version %s (0x%x) found at 0x%lx\n",
+ version, func_class & 0xf, (long)dev->hpa.start);
if (func_class < 2) {
printk(KERN_WARNING "Can't support LBA older than "
}
} else if (IS_MERCURY(dev) || IS_QUICKSILVER(dev)) {
+ int major, minor;
+
func_class &= 0xff;
- version = kmalloc(6, GFP_KERNEL);
- snprintf(version, 6, "TR%d.%d",(func_class >> 4),(func_class & 0xf));
+ major = func_class >> 4, minor = func_class & 0xf;
+
/* We could use one printk for both Elroy and Mercury,
* but for the mask for func_class.
*/
- printk(KERN_INFO "%s version %s (0x%x) found at 0x%lx\n",
- MODULE_NAME, version, func_class & 0xff, dev->hpa.start);
+ printk(KERN_INFO "%s version TR%d.%d (0x%x) found at 0x%lx\n",
+ IS_MERCURY(dev) ? "Mercury" : "Quicksilver", major,
+ minor, func_class, (long)dev->hpa.start);
+
cfg_ops = &mercury_cfg_ops;
} else {
- printk(KERN_ERR "Unknown LBA found at 0x%lx\n", dev->hpa.start);
+ printk(KERN_ERR "Unknown LBA found at 0x%lx\n",
+ (long)dev->hpa.start);
return -ENODEV;
}
- /*
- ** Tell I/O SAPIC driver we have a IRQ handler/region.
- */
+ /* Tell I/O SAPIC driver we have a IRQ handler/region. */
tmp_obj = iosapic_register(dev->hpa.start + LBA_IOSAPIC_BASE);
/* NOTE: PCI devices (e.g. 103c:1005 graphics card) which don't
lba_dev->hba.dev = dev;
lba_dev->iosapic_obj = tmp_obj; /* save interrupt handle */
lba_dev->hba.iommu = sba_get_iommu(dev); /* get iommu data */
+ parisc_set_drvdata(dev, lba_dev);
/* ------------ Second : initialize common stuff ---------- */
pci_bios = &lba_bios_ops;
lba_legacy_resources(dev, lba_dev);
}
- /*
- ** Tell PCI support another PCI bus was found.
- ** Walks PCI bus for us too.
- */
+ if (lba_dev->hba.bus_num.start < lba_next_bus)
+ lba_dev->hba.bus_num.start = lba_next_bus;
+
dev->dev.platform_data = lba_dev;
lba_bus = lba_dev->hba.hba_bus =
pci_scan_bus_parented(&dev->dev, lba_dev->hba.bus_num.start,
cfg_ops, NULL);
- if (lba_bus)
+ if (lba_bus) {
+ lba_next_bus = lba_bus->subordinate + 1;
pci_bus_add_devices(lba_bus);
+ }
/* This is in lieu of calling pci_assign_unassigned_resources() */
if (is_pdc_pat()) {
git.samba.org / sfrench / cifs-2.6.git / blobdiff