#include <net/dcbnl.h>
#define XGBE_DRV_NAME "amd-xgbe"
-#define XGBE_DRV_VERSION "1.0.2"
+#define XGBE_DRV_VERSION "1.0.3"
#define XGBE_DRV_DESC "AMD 10 Gigabit Ethernet Driver"
/* Descriptor related defines */
#define XGBE_MAX_DMA_CHANNELS 16
#define XGBE_MAX_QUEUES 16
+#define XGBE_PRIORITY_QUEUES 8
#define XGBE_DMA_STOP_TIMEOUT 5
/* DMA cache settings - Outer sharable, write-back, write-allocate */
#define XGMAC_MAX_STD_PACKET 1518
#define XGMAC_JUMBO_PACKET_MTU 9000
#define XGMAC_MAX_JUMBO_PACKET 9018
+#define XGMAC_ETH_PREAMBLE (12 + 8) /* Inter-frame gap + preamble */
+
+#define XGMAC_PFC_DATA_LEN 46
+#define XGMAC_PFC_DELAYS 14000
+
+#define XGMAC_PRIO_QUEUES(_cnt) \
+ min_t(unsigned int, IEEE_8021QAZ_MAX_TCS, (_cnt))
/* Common property names */
#define XGBE_MAC_ADDR_PROPERTY "mac-address"
#define XGBE_PHY_MODE_PROPERTY "phy-mode"
#define XGBE_DMA_IRQS_PROPERTY "amd,per-channel-interrupt"
#define XGBE_SPEEDSET_PROPERTY "amd,speed-set"
-#define XGBE_BLWC_PROPERTY "amd,serdes-blwc"
-#define XGBE_CDR_RATE_PROPERTY "amd,serdes-cdr-rate"
-#define XGBE_PQ_SKEW_PROPERTY "amd,serdes-pq-skew"
-#define XGBE_TX_AMP_PROPERTY "amd,serdes-tx-amp"
-#define XGBE_DFE_CFG_PROPERTY "amd,serdes-dfe-tap-config"
-#define XGBE_DFE_ENA_PROPERTY "amd,serdes-dfe-tap-enable"
/* Device-tree clock names */
#define XGBE_DMA_CLOCK "dma_clk"
#define XGMAC_DRIVER_CONTEXT 1
#define XGMAC_IOCTL_CONTEXT 2
-#define XGBE_FIFO_MAX 81920
+#define XGMAC_FIFO_RX_MAX 81920
+#define XGMAC_FIFO_TX_MAX 81920
+#define XGMAC_FIFO_MIN_ALLOC 2048
+#define XGMAC_FIFO_UNIT 256
+#define XGMAC_FIFO_ALIGN(_x) \
+ (((_x) + XGMAC_FIFO_UNIT - 1) & ~(XGMAC_FIFO_UNIT - 1))
+#define XGMAC_FIFO_FC_OFF 2048
+#define XGMAC_FIFO_FC_MIN 4096
#define XGBE_TC_MIN_QUANTUM 10
/* Flow control queue count */
#define XGMAC_MAX_FLOW_CONTROL_QUEUES 8
+/* Flow control threshold units */
+#define XGMAC_FLOW_CONTROL_UNIT 512
+#define XGMAC_FLOW_CONTROL_ALIGN(_x) \
+ (((_x) + XGMAC_FLOW_CONTROL_UNIT - 1) & ~(XGMAC_FLOW_CONTROL_UNIT - 1))
+#define XGMAC_FLOW_CONTROL_VALUE(_x) \
+ (((_x) < 1024) ? 0 : ((_x) / XGMAC_FLOW_CONTROL_UNIT) - 2)
+#define XGMAC_FLOW_CONTROL_MAX 33280
+
/* Maximum MAC address hash table size (256 bits = 8 bytes) */
#define XGBE_MAC_HASH_TABLE_SIZE 8
/* Auto-negotiation */
#define XGBE_AN_MS_TIMEOUT 500
-#define XGBE_LINK_TIMEOUT 10
-
-#define XGBE_AN_INT_CMPLT 0x01
-#define XGBE_AN_INC_LINK 0x02
-#define XGBE_AN_PG_RCV 0x04
-#define XGBE_AN_INT_MASK 0x07
-
-/* Rate-change complete wait/retry count */
-#define XGBE_RATECHANGE_COUNT 500
-
-/* Default SerDes settings */
-#define XGBE_SPEED_10000_BLWC 0
-#define XGBE_SPEED_10000_CDR 0x7
-#define XGBE_SPEED_10000_PLL 0x1
-#define XGBE_SPEED_10000_PQ 0x12
-#define XGBE_SPEED_10000_RATE 0x0
-#define XGBE_SPEED_10000_TXAMP 0xa
-#define XGBE_SPEED_10000_WORD 0x7
-#define XGBE_SPEED_10000_DFE_TAP_CONFIG 0x1
-#define XGBE_SPEED_10000_DFE_TAP_ENABLE 0x7f
-
-#define XGBE_SPEED_2500_BLWC 1
-#define XGBE_SPEED_2500_CDR 0x2
-#define XGBE_SPEED_2500_PLL 0x0
-#define XGBE_SPEED_2500_PQ 0xa
-#define XGBE_SPEED_2500_RATE 0x1
-#define XGBE_SPEED_2500_TXAMP 0xf
-#define XGBE_SPEED_2500_WORD 0x1
-#define XGBE_SPEED_2500_DFE_TAP_CONFIG 0x3
-#define XGBE_SPEED_2500_DFE_TAP_ENABLE 0x0
-
-#define XGBE_SPEED_1000_BLWC 1
-#define XGBE_SPEED_1000_CDR 0x2
-#define XGBE_SPEED_1000_PLL 0x0
-#define XGBE_SPEED_1000_PQ 0xa
-#define XGBE_SPEED_1000_RATE 0x3
-#define XGBE_SPEED_1000_TXAMP 0xf
-#define XGBE_SPEED_1000_WORD 0x1
-#define XGBE_SPEED_1000_DFE_TAP_CONFIG 0x3
-#define XGBE_SPEED_1000_DFE_TAP_ENABLE 0x0
+#define XGBE_LINK_TIMEOUT 5
+
+#define XGBE_SGMII_AN_LINK_STATUS BIT(1)
+#define XGBE_SGMII_AN_LINK_SPEED (BIT(2) | BIT(3))
+#define XGBE_SGMII_AN_LINK_SPEED_100 0x04
+#define XGBE_SGMII_AN_LINK_SPEED_1000 0x08
+#define XGBE_SGMII_AN_LINK_DUPLEX BIT(4)
struct xgbe_prv_data;
XGBE_SPEEDS,
};
+enum xgbe_xpcs_access {
+ XGBE_XPCS_ACCESS_V1 = 0,
+ XGBE_XPCS_ACCESS_V2,
+};
+
+enum xgbe_an_mode {
+ XGBE_AN_MODE_CL73 = 0,
+ XGBE_AN_MODE_CL37,
+ XGBE_AN_MODE_CL37_SGMII,
+ XGBE_AN_MODE_NONE,
+};
+
enum xgbe_an {
XGBE_AN_READY = 0,
XGBE_AN_PAGE_RECEIVED,
};
enum xgbe_mode {
- XGBE_MODE_KR = 0,
- XGBE_MODE_KX,
+ XGBE_MODE_KX_1000 = 0,
+ XGBE_MODE_KX_2500,
+ XGBE_MODE_KR,
+ XGBE_MODE_UNKNOWN,
};
enum xgbe_speedset {
int (*read_mmd_regs)(struct xgbe_prv_data *, int, int);
void (*write_mmd_regs)(struct xgbe_prv_data *, int, int, int);
- int (*set_gmii_speed)(struct xgbe_prv_data *);
- int (*set_gmii_2500_speed)(struct xgbe_prv_data *);
- int (*set_xgmii_speed)(struct xgbe_prv_data *);
+ int (*set_speed)(struct xgbe_prv_data *, int);
void (*enable_tx)(struct xgbe_prv_data *);
void (*disable_tx)(struct xgbe_prv_data *);
int (*set_rss_lookup_table)(struct xgbe_prv_data *, const u32 *);
};
+/* This structure represents implementation specific routines for an
+ * implementation of a PHY. All routines are required unless noted below.
+ * Optional routines:
+ * kr_training_pre, kr_training_post
+ */
+struct xgbe_phy_impl_if {
+ /* Perform Setup/teardown actions */
+ int (*init)(struct xgbe_prv_data *);
+ void (*exit)(struct xgbe_prv_data *);
+
+ /* Perform start/stop specific actions */
+ int (*reset)(struct xgbe_prv_data *);
+ int (*start)(struct xgbe_prv_data *);
+ void (*stop)(struct xgbe_prv_data *);
+
+ /* Return the link status */
+ int (*link_status)(struct xgbe_prv_data *);
+
+ /* Indicate if a particular speed is valid */
+ bool (*valid_speed)(struct xgbe_prv_data *, int);
+
+ /* Check if the specified mode can/should be used */
+ bool (*use_mode)(struct xgbe_prv_data *, enum xgbe_mode);
+ /* Switch the PHY into various modes */
+ void (*set_mode)(struct xgbe_prv_data *, enum xgbe_mode);
+ /* Retrieve mode needed for a specific speed */
+ enum xgbe_mode (*get_mode)(struct xgbe_prv_data *, int);
+ /* Retrieve new/next mode when trying to auto-negotiate */
+ enum xgbe_mode (*switch_mode)(struct xgbe_prv_data *);
+ /* Retrieve current mode */
+ enum xgbe_mode (*cur_mode)(struct xgbe_prv_data *);
+
+ /* Retrieve current auto-negotiation mode */
+ enum xgbe_an_mode (*an_mode)(struct xgbe_prv_data *);
+
+ /* Process results of auto-negotiation */
+ enum xgbe_mode (*an_outcome)(struct xgbe_prv_data *);
+
+ /* Pre/Post KR training enablement support */
+ void (*kr_training_pre)(struct xgbe_prv_data *);
+ void (*kr_training_post)(struct xgbe_prv_data *);
+};
+
struct xgbe_phy_if {
- /* For initial PHY setup */
- void (*phy_init)(struct xgbe_prv_data *);
+ /* For PHY setup/teardown */
+ int (*phy_init)(struct xgbe_prv_data *);
+ void (*phy_exit)(struct xgbe_prv_data *);
/* For PHY support when setting device up/down */
int (*phy_reset)(struct xgbe_prv_data *);
/* For PHY support while device is up */
void (*phy_status)(struct xgbe_prv_data *);
int (*phy_config_aneg)(struct xgbe_prv_data *);
+
+ /* For PHY settings validation */
+ bool (*phy_valid_speed)(struct xgbe_prv_data *, int);
+
+ /* PHY implementation specific services */
+ struct xgbe_phy_impl_if phy_impl;
};
struct xgbe_desc_if {
unsigned int aux_snap_num; /* Number of Aux snapshot inputs */
};
+struct xgbe_version_data {
+ void (*init_function_ptrs_phy_impl)(struct xgbe_phy_if *);
+ enum xgbe_xpcs_access xpcs_access;
+};
+
struct xgbe_prv_data {
struct net_device *netdev;
struct platform_device *pdev;
struct acpi_device *adev;
struct device *dev;
+ struct platform_device *phy_pdev;
+ struct device *phy_dev;
+
+ /* Version related data */
+ struct xgbe_version_data *vdata;
/* ACPI or DT flag */
unsigned int use_acpi;
/* XPCS indirect addressing lock */
spinlock_t xpcs_lock;
+ unsigned int xpcs_window;
+ unsigned int xpcs_window_size;
+ unsigned int xpcs_window_mask;
/* RSS addressing mutex */
struct mutex rss_mutex;
unsigned int pause_autoneg;
unsigned int tx_pause;
unsigned int rx_pause;
+ unsigned int rx_rfa[XGBE_MAX_QUEUES];
+ unsigned int rx_rfd[XGBE_MAX_QUEUES];
/* Receive Side Scaling settings */
u8 rss_key[XGBE_RSS_HASH_KEY_SIZE];
struct ieee_pfc *pfc;
unsigned int q2tc_map[XGBE_MAX_QUEUES];
unsigned int prio2q_map[IEEE_8021QAZ_MAX_TCS];
+ unsigned int pfcq[XGBE_MAX_QUEUES];
+ unsigned int pfc_rfa;
u8 num_tcs;
/* Hardware features of the device */
int phy_speed;
/* MDIO/PHY related settings */
+ unsigned int phy_started;
+ void *phy_data;
struct xgbe_phy phy;
int mdio_mmd;
unsigned long link_check;
int an_irq;
struct work_struct an_irq_work;
- unsigned int speed_set;
-
- /* SerDes UEFI configurable settings.
- * Switching between modes/speeds requires new values for some
- * SerDes settings. The values can be supplied as device
- * properties in array format. The first array entry is for
- * 1GbE, second for 2.5GbE and third for 10GbE
- */
- u32 serdes_blwc[XGBE_SPEEDS];
- u32 serdes_cdr_rate[XGBE_SPEEDS];
- u32 serdes_pq_skew[XGBE_SPEEDS];
- u32 serdes_tx_amp[XGBE_SPEEDS];
- u32 serdes_dfe_tap_cfg[XGBE_SPEEDS];
- u32 serdes_dfe_tap_ena[XGBE_SPEEDS];
-
/* Auto-negotiation state machine support */
unsigned int an_int;
+ unsigned int an_status;
struct mutex an_mutex;
enum xgbe_an an_result;
enum xgbe_an an_state;
unsigned int parallel_detect;
unsigned int fec_ability;
unsigned long an_start;
+ enum xgbe_an_mode an_mode;
unsigned int lpm_ctrl; /* CTRL1 for resume */
void xgbe_init_function_ptrs_dev(struct xgbe_hw_if *);
void xgbe_init_function_ptrs_phy(struct xgbe_phy_if *);
+void xgbe_init_function_ptrs_phy_v1(struct xgbe_phy_if *);
void xgbe_init_function_ptrs_desc(struct xgbe_desc_if *);
const struct net_device_ops *xgbe_get_netdev_ops(void);
const struct ethtool_ops *xgbe_get_ethtool_ops(void);
git.samba.org / sfrench / cifs-2.6.git / blobdiff