#define DRV_VERSION "0.5.1"
struct sis_chipset {
- u16 device; /* PCI host ID */
- struct ata_port_info *info; /* Info block */
+ u16 device; /* PCI host ID */
+ const struct ata_port_info *info; /* Info block */
/* Probably add family, cable detect type etc here to clean
up code later */
};
}
/**
- * sis_port_base - return PCI configuration base for dev
+ * sis_old_port_base - return PCI configuration base for dev
* @adev: device
*
* Returns the base of the PCI configuration registers for this port
* number.
*/
-static int sis_port_base(struct ata_device *adev)
+static int sis_old_port_base(struct ata_device *adev)
{
return 0x40 + (4 * adev->ap->port_no) + (2 * adev->devno);
}
/**
* sis_133_cable_detect - check for 40/80 pin
* @ap: Port
+ * @deadline: deadline jiffies for the operation
*
* Perform cable detection for the later UDMA133 capable
* SiS chipset.
/**
* sis_66_cable_detect - check for 40/80 pin
* @ap: Port
+ * @deadline: deadline jiffies for the operation
*
* Perform cable detection on the UDMA66, UDMA100 and early UDMA133
* SiS IDE controllers.
/**
* sis_pre_reset - probe begin
* @ap: ATA port
+ * @deadline: deadline jiffies for the operation
*
* Set up cable type and use generic probe init
*/
-static int sis_pre_reset(struct ata_port *ap)
+static int sis_pre_reset(struct ata_port *ap, unsigned long deadline)
{
static const struct pci_bits sis_enable_bits[] = {
{ 0x4aU, 1U, 0x02UL, 0x02UL }, /* port 0 */
if (!pci_test_config_bits(pdev, &sis_enable_bits[ap->port_no]))
return -ENOENT;
- return ata_std_prereset(ap);
+
+ return ata_std_prereset(ap, deadline);
}
static void sis_old_set_piomode (struct ata_port *ap, struct ata_device *adev)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- int port = sis_port_base(adev);
+ int port = sis_old_port_base(adev);
u8 t1, t2;
int speed = adev->pio_mode - XFER_PIO_0;
static void sis_100_set_piomode (struct ata_port *ap, struct ata_device *adev)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- int port = sis_port_base(adev);
+ int port = sis_old_port_base(adev);
int speed = adev->pio_mode - XFER_PIO_0;
const u8 actrec[] = { 0x00, 0x67, 0x44, 0x33, 0x31 };
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int speed = adev->dma_mode - XFER_MW_DMA_0;
- int drive_pci = sis_port_base(adev);
+ int drive_pci = sis_old_port_base(adev);
u16 timing;
const u16 mwdma_bits[] = { 0x707, 0x202, 0x202 };
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int speed = adev->dma_mode - XFER_MW_DMA_0;
- int drive_pci = sis_port_base(adev);
+ int drive_pci = sis_old_port_base(adev);
u16 timing;
const u16 mwdma_bits[] = { 0x707, 0x202, 0x202 };
if (adev->dma_mode < XFER_UDMA_0) {
/* bits 3-0 hold recovery timing bits 8-10 active timing and
the higer bits are dependant on the device, bit 15 udma */
- timing &= ~ 0x870F;
+ timing &= ~0x870F;
timing |= mwdma_bits[speed];
} else {
/* Bit 15 is UDMA on/off, bit 12-14 are cycle time */
speed = adev->dma_mode - XFER_UDMA_0;
- timing &= ~0x6000;
+ timing &= ~0xF000;
timing |= udma_bits[speed];
}
pci_write_config_word(pdev, drive_pci, timing);
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int speed = adev->dma_mode - XFER_MW_DMA_0;
- int drive_pci = sis_port_base(adev);
- u16 timing;
+ int drive_pci = sis_old_port_base(adev);
+ u8 timing;
- const u16 udma_bits[] = { 0x8B00, 0x8700, 0x8500, 0x8300, 0x8200, 0x8100};
+ const u8 udma_bits[] = { 0x8B, 0x87, 0x85, 0x83, 0x82, 0x81};
- pci_read_config_word(pdev, drive_pci, &timing);
+ pci_read_config_byte(pdev, drive_pci + 1, &timing);
if (adev->dma_mode < XFER_UDMA_0) {
/* NOT SUPPORTED YET: NEED DATA SHEET. DITTO IN OLD DRIVER */
} else {
- /* Bit 15 is UDMA on/off, bit 12-14 are cycle time */
+ /* Bit 7 is UDMA on/off, bit 0-3 are cycle time */
speed = adev->dma_mode - XFER_UDMA_0;
- timing &= ~0x0F00;
+ timing &= ~0x8F;
timing |= udma_bits[speed];
}
- pci_write_config_word(pdev, drive_pci, timing);
+ pci_write_config_byte(pdev, drive_pci + 1, timing);
}
/**
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int speed = adev->dma_mode - XFER_MW_DMA_0;
- int drive_pci = sis_port_base(adev);
- u16 timing;
-
- static const u16 udma_bits[] = { 0x8F00, 0x8A00, 0x8700, 0x8500, 0x8300, 0x8200, 0x8100};
+ int drive_pci = sis_old_port_base(adev);
+ u8 timing;
+ /* Low 4 bits are timing */
+ static const u8 udma_bits[] = { 0x8F, 0x8A, 0x87, 0x85, 0x83, 0x82, 0x81};
- pci_read_config_word(pdev, drive_pci, &timing);
+ pci_read_config_byte(pdev, drive_pci + 1, &timing);
if (adev->dma_mode < XFER_UDMA_0) {
/* NOT SUPPORTED YET: NEED DATA SHEET. DITTO IN OLD DRIVER */
} else {
- /* Bit 15 is UDMA on/off, bit 12-14 are cycle time */
+ /* Bit 7 is UDMA on/off, bit 0-3 are cycle time */
speed = adev->dma_mode - XFER_UDMA_0;
- timing &= ~0x0F00;
+ timing &= ~0x8F;
timing |= udma_bits[speed];
}
- pci_write_config_word(pdev, drive_pci, timing);
+ pci_write_config_byte(pdev, drive_pci + 1, timing);
}
/**
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
-#ifdef CONFIG_PM
- .resume = ata_scsi_device_resume,
- .suspend = ata_scsi_device_suspend,
-#endif
};
static const struct ata_port_operations sis_133_ops = {
.port_start = ata_port_start,
};
+static const struct ata_port_operations sis_133_for_sata_ops = {
+ .port_disable = ata_port_disable,
+ .set_piomode = sis_133_set_piomode,
+ .set_dmamode = sis_133_set_dmamode,
+ .mode_filter = ata_pci_default_filter,
+
+ .tf_load = ata_tf_load,
+ .tf_read = ata_tf_read,
+ .check_status = ata_check_status,
+ .exec_command = ata_exec_command,
+ .dev_select = ata_std_dev_select,
+
+ .freeze = ata_bmdma_freeze,
+ .thaw = ata_bmdma_thaw,
+ .error_handler = ata_bmdma_error_handler,
+ .post_internal_cmd = ata_bmdma_post_internal_cmd,
+ .cable_detect = sis_133_cable_detect,
+
+ .bmdma_setup = ata_bmdma_setup,
+ .bmdma_start = ata_bmdma_start,
+ .bmdma_stop = ata_bmdma_stop,
+ .bmdma_status = ata_bmdma_status,
+ .qc_prep = ata_qc_prep,
+ .qc_issue = ata_qc_issue_prot,
+ .data_xfer = ata_data_xfer,
+
+ .irq_handler = ata_interrupt,
+ .irq_clear = ata_bmdma_irq_clear,
+ .irq_on = ata_irq_on,
+ .irq_ack = ata_irq_ack,
+
+ .port_start = ata_port_start,
+};
+
static const struct ata_port_operations sis_133_early_ops = {
.port_disable = ata_port_disable,
.set_piomode = sis_100_set_piomode,
.port_start = ata_port_start,
};
-static struct ata_port_info sis_info = {
+static const struct ata_port_info sis_info = {
.sht = &sis_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = 0,
.port_ops = &sis_old_ops,
};
-static struct ata_port_info sis_info33 = {
+static const struct ata_port_info sis_info33 = {
.sht = &sis_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA2, /* UDMA 33 */
.port_ops = &sis_old_ops,
};
-static struct ata_port_info sis_info66 = {
+static const struct ata_port_info sis_info66 = {
.sht = &sis_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA4, /* UDMA 66 */
.port_ops = &sis_66_ops,
};
-static struct ata_port_info sis_info100 = {
+static const struct ata_port_info sis_info100 = {
.sht = &sis_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA5,
.port_ops = &sis_100_ops,
};
-static struct ata_port_info sis_info100_early = {
+static const struct ata_port_info sis_info100_early = {
.sht = &sis_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.udma_mask = ATA_UDMA5,
.pio_mask = 0x1f, /* pio0-4 */
.port_ops = &sis_66_ops,
};
-struct ata_port_info sis_info133 = {
+static const struct ata_port_info sis_info133 = {
.sht = &sis_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &sis_133_ops,
};
-static struct ata_port_info sis_info133_early = {
+const struct ata_port_info sis_info133_for_sata = {
+ .sht = &sis_sht,
+ .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .udma_mask = ATA_UDMA6,
+ .port_ops = &sis_133_for_sata_ops,
+};
+static const struct ata_port_info sis_info133_early = {
.sht = &sis_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f, /* pio0-4 */
};
/* Privately shared with the SiS180 SATA driver, not for use elsewhere */
-EXPORT_SYMBOL_GPL(sis_info133);
+EXPORT_SYMBOL_GPL(sis_info133_for_sata);
static void sis_fixup(struct pci_dev *pdev, struct sis_chipset *sis)
{
static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
{
static int printed_version;
- static struct ata_port_info *port_info[2];
- struct ata_port_info *port;
+ struct ata_port_info port;
+ const struct ata_port_info *ppi[] = { &port, NULL };
struct pci_dev *host = NULL;
struct sis_chipset *chipset = NULL;
struct sis_chipset *sets;
if (chipset == NULL)
return -ENODEV;
- port = chipset->info;
- port->private_data = chipset;
+ port = *chipset->info;
+ port.private_data = chipset;
sis_fixup(pdev, chipset);
- port_info[0] = port_info[1] = port;
- return ata_pci_init_one(pdev, port_info, 2);
+ return ata_pci_init_one(pdev, ppi);
}
static const struct pci_device_id sis_pci_tbl[] = {
{ PCI_VDEVICE(SI, 0x5513), }, /* SiS 5513 */
{ PCI_VDEVICE(SI, 0x5518), }, /* SiS 5518 */
+ { PCI_VDEVICE(SI, 0x1180), }, /* SiS 1180 */
{ }
};
git.samba.org / sfrench / cifs-2.6.git / blobdiff