* for paravirtualization. The following will never clobber any registers:
* INTERRUPT_RETURN (aka. "iret")
* GET_CR0_INTO_EAX (aka. "movl %cr0, %eax")
- * ENABLE_INTERRUPTS_SYSEXIT (aka "sti; sysexit").
+ * ENABLE_INTERRUPTS_SYSCALL_RET (aka "sti; sysexit").
*
* For DISABLE_INTERRUPTS/ENABLE_INTERRUPTS (aka "cli"/"sti"), you must
* specify what registers can be overwritten (CLBR_NONE, CLBR_EAX/EDX/ECX/ANY).
jb resume_kernel # not returning to v8086 or userspace
ENTRY(resume_userspace)
+ LOCKDEP_SYS_EXIT
DISABLE_INTERRUPTS(CLBR_ANY) # make sure we don't miss an interrupt
# setting need_resched or sigpending
# between sampling and the iret
the vsyscall page. See vsyscall-sysentry.S, which defines the symbol. */
# sysenter call handler stub
-ENTRY(sysenter_entry)
+ENTRY(ia32_sysenter_target)
CFI_STARTPROC simple
CFI_SIGNAL_FRAME
CFI_DEF_CFA esp, 0
CFI_REGISTER esp, ebp
- movl TSS_sysenter_esp0(%esp),%esp
+ movl TSS_sysenter_sp0(%esp),%esp
sysenter_past_esp:
/*
* No need to follow this irqs on/off section: the syscall
jae syscall_badsys
call *sys_call_table(,%eax,4)
movl %eax,PT_EAX(%esp)
+ LOCKDEP_SYS_EXIT
DISABLE_INTERRUPTS(CLBR_ANY)
TRACE_IRQS_OFF
movl TI_flags(%ebp), %ecx
xorl %ebp,%ebp
TRACE_IRQS_ON
1: mov PT_FS(%esp), %fs
- ENABLE_INTERRUPTS_SYSEXIT
+ ENABLE_INTERRUPTS_SYSCALL_RET
CFI_ENDPROC
.pushsection .fixup,"ax"
2: movl $0,PT_FS(%esp)
.align 4
.long 1b,2b
.popsection
-ENDPROC(sysenter_entry)
+ENDPROC(ia32_sysenter_target)
# system call handler stub
ENTRY(system_call)
call *sys_call_table(,%eax,4)
movl %eax,PT_EAX(%esp) # store the return value
syscall_exit:
+ LOCKDEP_SYS_EXIT
DISABLE_INTERRUPTS(CLBR_ANY) # make sure we don't miss an interrupt
# setting need_resched or sigpending
# between sampling and the iret
RESTORE_REGS
addl $4, %esp # skip orig_eax/error_code
CFI_ADJUST_CFA_OFFSET -4
-1: INTERRUPT_RETURN
+ENTRY(irq_return)
+ INTERRUPT_RETURN
.section .fixup,"ax"
iret_exc:
pushl $0 # no error code
.previous
.section __ex_table,"a"
.align 4
- .long 1b,iret_exc
+ .long irq_return,iret_exc
.previous
CFI_RESTORE_STATE
* is still available to implement the setting of the high
* 16-bits in the INTERRUPT_RETURN paravirt-op.
*/
- cmpl $0, paravirt_ops+PARAVIRT_enabled
+ cmpl $0, pv_info+PARAVIRT_enabled
jne restore_nocheck
#endif
jz work_notifysig
work_resched:
call schedule
+ LOCKDEP_SYS_EXIT
DISABLE_INTERRUPTS(CLBR_ANY) # make sure we don't miss an interrupt
# setting need_resched or sigpending
# between sampling and the iret
* Build the entry stubs and pointer table with
* some assembler magic.
*/
-.data
+.section .rodata,"a"
ENTRY(interrupt)
.text
* that sets up the real kernel stack. Check here, since we can't
* allow the wrong stack to be used.
*
- * "TSS_sysenter_esp0+12" is because the NMI/debug handler will have
+ * "TSS_sysenter_sp0+12" is because the NMI/debug handler will have
* already pushed 3 words if it hits on the sysenter instruction:
* eflags, cs and eip.
*
cmpw $__KERNEL_CS,4(%esp); \
jne ok; \
label: \
- movl TSS_sysenter_esp0+offset(%esp),%esp; \
+ movl TSS_sysenter_sp0+offset(%esp),%esp; \
CFI_DEF_CFA esp, 0; \
CFI_UNDEFINED eip; \
pushfl; \
KPROBE_ENTRY(debug)
RING0_INT_FRAME
- cmpl $sysenter_entry,(%esp)
+ cmpl $ia32_sysenter_target,(%esp)
jne debug_stack_correct
FIX_STACK(12, debug_stack_correct, debug_esp_fix_insn)
debug_stack_correct:
popl %eax
CFI_ADJUST_CFA_OFFSET -4
je nmi_espfix_stack
- cmpl $sysenter_entry,(%esp)
+ cmpl $ia32_sysenter_target,(%esp)
je nmi_stack_fixup
pushl %eax
CFI_ADJUST_CFA_OFFSET 4
popl %eax
CFI_ADJUST_CFA_OFFSET -4
jae nmi_stack_correct
- cmpl $sysenter_entry,12(%esp)
+ cmpl $ia32_sysenter_target,12(%esp)
je nmi_debug_stack_check
nmi_stack_correct:
/* We have a RING0_INT_FRAME here */
RESTORE_REGS
lss 12+4(%esp), %esp # back to espfix stack
CFI_ADJUST_CFA_OFFSET -24
-1: INTERRUPT_RETURN
+ jmp irq_return
CFI_ENDPROC
-.section __ex_table,"a"
- .align 4
- .long 1b,iret_exc
-.previous
KPROBE_END(nmi)
#ifdef CONFIG_PARAVIRT
ENTRY(native_iret)
-1: iret
+ iret
.section __ex_table,"a"
.align 4
- .long 1b,iret_exc
+ .long native_iret, iret_exc
.previous
END(native_iret)
-ENTRY(native_irq_enable_sysexit)
+ENTRY(native_irq_enable_syscall_ret)
sti
sysexit
-END(native_irq_enable_sysexit)
+END(native_irq_enable_syscall_ret)
#endif
KPROBE_ENTRY(int3)