** modifier UNLESS the lower order bits are saved and ORed back in when
** the macro is used.
*************************************************************************************/
-/*
-** ********************* PLL AND RESET MASKS ****************************************/
-/* PLL_CTL Masks */
-#define DF 0x0001 /* 0: PLL = CLKIN, 1: PLL = CLKIN/2 */
-#define PLL_OFF 0x0002 /* PLL Not Powered */
-#define STOPCK 0x0008 /* Core Clock Off */
-#define PDWN 0x0020 /* Enter Deep Sleep Mode */
-#define IN_DELAY 0x0040 /* Add 200ps Delay To EBIU Input Latches */
-#define OUT_DELAY 0x0080 /* Add 200ps Delay To EBIU Output Signals */
-#define BYPASS 0x0100 /* Bypass the PLL */
-#define MSEL 0x7E00 /* Multiplier Select For CCLK/VCO Factors */
-/* PLL_CTL Macros (Only Use With Logic OR While Setting Lower Order Bits) */
-#define SET_MSEL(x) (((x)&0x3F) << 0x9) /* Set MSEL = 0-63 --> VCO = CLKIN*MSEL */
-
-/* PLL_DIV Masks */
-#define SSEL 0x000F /* System Select */
-#define CSEL 0x0030 /* Core Select */
-#define CSEL_DIV1 0x0000 /* CCLK = VCO / 1 */
-#define CSEL_DIV2 0x0010 /* CCLK = VCO / 2 */
-#define CSEL_DIV4 0x0020 /* CCLK = VCO / 4 */
-#define CSEL_DIV8 0x0030 /* CCLK = VCO / 8 */
-/* PLL_DIV Macros */
-#define SET_SSEL(x) ((x)&0xF) /* Set SSEL = 0-15 --> SCLK = VCO/SSEL */
-
-/* VR_CTL Masks */
-#define FREQ 0x3000 /* Switching Oscillator Frequency For Regulator */
-#define HIBERNATE 0x0000 /* Powerdown/Bypass On-Board Regulation */
-
-#define VLEV 0x00F0 /* Internal Voltage Level */
-#define VLEV_085 0x0060 /* VLEV = 0.85 V (-5% - +10% Accuracy) */
-#define VLEV_090 0x0070 /* VLEV = 0.90 V (-5% - +10% Accuracy) */
-#define VLEV_095 0x0080 /* VLEV = 0.95 V (-5% - +10% Accuracy) */
-#define VLEV_100 0x0090 /* VLEV = 1.00 V (-5% - +10% Accuracy) */
-#define VLEV_105 0x00A0 /* VLEV = 1.05 V (-5% - +10% Accuracy) */
-#define VLEV_110 0x00B0 /* VLEV = 1.10 V (-5% - +10% Accuracy) */
-#define VLEV_115 0x00C0 /* VLEV = 1.15 V (-5% - +10% Accuracy) */
-#define VLEV_120 0x00D0 /* VLEV = 1.20 V (-5% - +10% Accuracy) */
-#define VLEV_125 0x00E0 /* VLEV = 1.25 V (-5% - +10% Accuracy) */
-#define VLEV_130 0x00F0 /* VLEV = 1.30 V (-5% - +10% Accuracy) */
-
-#define WAKE 0x0100 /* Enable RTC/Reset Wakeup From Hibernate */
-#define USBWE 0x0200 /* Enable USB Wakeup From Hibernate */
-#define PHYWE 0x0400 /* Enable PHY Wakeup From Hibernate */
-#define CLKBUFOE 0x4000 /* CLKIN Buffer Output Enable */
-#define PHYCLKOE CLKBUFOE /* Alternative legacy name for the above */
-#define SCKELOW 0x8000 /* Enable Drive CKE Low During Reset */
-
-/* PLL_STAT Masks */
-#define ACTIVE_PLLENABLED 0x0001 /* Processor In Active Mode With PLL Enabled */
-#define FULL_ON 0x0002 /* Processor In Full On Mode */
-#define ACTIVE_PLLDISABLED 0x0004 /* Processor In Active Mode With PLL Disabled */
-#define PLL_LOCKED 0x0020 /* PLL_LOCKCNT Has Been Reached */
/* CHIPID Masks */
#define CHIPID_VERSION 0xF0000000
#define IWR_DISABLE(x) (0xFFFFFFFF ^ (1 << ((x)&0x1F))) /* Wakeup Disable Peripheral #x */
-/* ********* WATCHDOG TIMER MASKS ******************** */
-
-/* Watchdog Timer WDOG_CTL Register Masks */
-
-#define WDEV(x) (((x)<<1) & 0x0006) /* event generated on roll over */
-#define WDEV_RESET 0x0000 /* generate reset event on roll over */
-#define WDEV_NMI 0x0002 /* generate NMI event on roll over */
-#define WDEV_GPI 0x0004 /* generate GP IRQ on roll over */
-#define WDEV_NONE 0x0006 /* no event on roll over */
-#define WDEN 0x0FF0 /* enable watchdog */
-#define WDDIS 0x0AD0 /* disable watchdog */
-#define WDRO 0x8000 /* watchdog rolled over latch */
-
-/* depreciated WDOG_CTL Register Masks for legacy code */
-
-
-#define ICTL WDEV
-#define ENABLE_RESET WDEV_RESET
-#define WDOG_RESET WDEV_RESET
-#define ENABLE_NMI WDEV_NMI
-#define WDOG_NMI WDEV_NMI
-#define ENABLE_GPI WDEV_GPI
-#define WDOG_GPI WDEV_GPI
-#define DISABLE_EVT WDEV_NONE
-#define WDOG_NONE WDEV_NONE
-
-#define TMR_EN WDEN
-#define TMR_DIS WDDIS
-#define TRO WDRO
-#define ICTL_P0 0x01
- #define ICTL_P1 0x02
-#define TRO_P 0x0F
-
-
-
-/* *************** REAL TIME CLOCK MASKS **************************/
-/* RTC_STAT and RTC_ALARM Masks */
-#define RTC_SEC 0x0000003F /* Real-Time Clock Seconds */
-#define RTC_MIN 0x00000FC0 /* Real-Time Clock Minutes */
-#define RTC_HR 0x0001F000 /* Real-Time Clock Hours */
-#define RTC_DAY 0xFFFE0000 /* Real-Time Clock Days */
-
-/* RTC_ALARM Macro z=day y=hr x=min w=sec */
-#define SET_ALARM(z,y,x,w) ((((z)&0x7FFF)<<0x11)|(((y)&0x1F)<<0xC)|(((x)&0x3F)<<0x6)|((w)&0x3F))
-
-/* RTC_ICTL and RTC_ISTAT Masks */
-#define STOPWATCH 0x0001 /* Stopwatch Interrupt Enable */
-#define ALARM 0x0002 /* Alarm Interrupt Enable */
-#define SECOND 0x0004 /* Seconds (1 Hz) Interrupt Enable */
-#define MINUTE 0x0008 /* Minutes Interrupt Enable */
-#define HOUR 0x0010 /* Hours Interrupt Enable */
-#define DAY 0x0020 /* 24 Hours (Days) Interrupt Enable */
-#define DAY_ALARM 0x0040 /* Day Alarm (Day, Hour, Minute, Second) Interrupt Enable */
-#define WRITE_PENDING 0x4000 /* Write Pending Status */
-#define WRITE_COMPLETE 0x8000 /* Write Complete Interrupt Enable */
-
-/* RTC_FAST / RTC_PREN Mask */
-#define PREN 0x0001 /* Enable Prescaler, RTC Runs @1 Hz */
-
-
/* ************** UART CONTROLLER MASKS *************************/
/* UARTx_LCR Masks */
#define WLS(x) (((x)-5) & 0x03) /* Word Length Select */
/* ************************** DMA CONTROLLER MASKS ********************************/
-/* DMAx_CONFIG, MDMA_yy_CONFIG Masks */
-#define DMAEN 0x0001 /* DMA Channel Enable */
-#define WNR 0x0002 /* Channel Direction (W/R*) */
-#define WDSIZE_8 0x0000 /* Transfer Word Size = 8 */
-#define WDSIZE_16 0x0004 /* Transfer Word Size = 16 */
-#define WDSIZE_32 0x0008 /* Transfer Word Size = 32 */
-#define DMA2D 0x0010 /* DMA Mode (2D/1D*) */
-#define RESTART 0x0020 /* DMA Buffer Clear */
-#define DI_SEL 0x0040 /* Data Interrupt Timing Select */
-#define DI_EN 0x0080 /* Data Interrupt Enable */
-#define NDSIZE_0 0x0000 /* Next Descriptor Size = 0 (Stop/Autobuffer) */
-#define NDSIZE_1 0x0100 /* Next Descriptor Size = 1 */
-#define NDSIZE_2 0x0200 /* Next Descriptor Size = 2 */
-#define NDSIZE_3 0x0300 /* Next Descriptor Size = 3 */
-#define NDSIZE_4 0x0400 /* Next Descriptor Size = 4 */
-#define NDSIZE_5 0x0500 /* Next Descriptor Size = 5 */
-#define NDSIZE_6 0x0600 /* Next Descriptor Size = 6 */
-#define NDSIZE_7 0x0700 /* Next Descriptor Size = 7 */
-#define NDSIZE_8 0x0800 /* Next Descriptor Size = 8 */
-#define NDSIZE_9 0x0900 /* Next Descriptor Size = 9 */
-#define NDSIZE 0x0900 /* Next Descriptor Size */
-#define DMAFLOW 0x7000 /* Flow Control */
-#define DMAFLOW_STOP 0x0000 /* Stop Mode */
-#define DMAFLOW_AUTO 0x1000 /* Autobuffer Mode */
-#define DMAFLOW_ARRAY 0x4000 /* Descriptor Array Mode */
-#define DMAFLOW_SMALL 0x6000 /* Small Model Descriptor List Mode */
-#define DMAFLOW_LARGE 0x7000 /* Large Model Descriptor List Mode */
/* DMAx_PERIPHERAL_MAP, MDMA_yy_PERIPHERAL_MAP Masks */
#define CTYPE 0x0040 /* DMA Channel Type Indicator (Memory/Peripheral*) */
#define PMAP_UART1RX 0xA000 /* UART1 Port Receive DMA */
#define PMAP_UART1TX 0xB000 /* UART1 Port Transmit DMA */
-/* DMAx_IRQ_STATUS, MDMA_yy_IRQ_STATUS Masks */
-#define DMA_DONE 0x0001 /* DMA Completion Interrupt Status */
-#define DMA_ERR 0x0002 /* DMA Error Interrupt Status */
-#define DFETCH 0x0004 /* DMA Descriptor Fetch Indicator */
-#define DMA_RUN 0x0008 /* DMA Channel Running Indicator */
-
-
/* ************ PARALLEL PERIPHERAL INTERFACE (PPI) MASKS *************/
/* PPI_CONTROL Masks */
#define PORT_EN 0x0001 /* PPI Port Enable */
#define BNDMODE_CAPT 0x2000 /* boundary capture mode */
#define BNDMODE_AEXT 0x3000 /* boundary auto-extend mode */
-/* Bit masks for OTP_CONTROL */
-
-#define FUSE_FADDR 0x1ff /* OTP/Fuse Address */
-#define FIEN 0x800 /* OTP/Fuse Interrupt Enable */
-#define nFIEN 0x0
-#define FTESTDEC 0x1000 /* OTP/Fuse Test Decoder */
-#define nFTESTDEC 0x0
-#define FWRTEST 0x2000 /* OTP/Fuse Write Test */
-#define nFWRTEST 0x0
-#define FRDEN 0x4000 /* OTP/Fuse Read Enable */
-#define nFRDEN 0x0
-#define FWREN 0x8000 /* OTP/Fuse Write Enable */
-#define nFWREN 0x0
-
-/* Bit masks for OTP_BEN */
-
-#define FBEN 0xffff /* OTP/Fuse Byte Enable */
-
-/* Bit masks for OTP_STATUS */
-
-#define FCOMP 0x1 /* OTP/Fuse Access Complete */
-#define nFCOMP 0x0
-#define FERROR 0x2 /* OTP/Fuse Access Error */
-#define nFERROR 0x0
-#define MMRGLOAD 0x10 /* Memory Mapped Register Gasket Load */
-#define nMMRGLOAD 0x0
-#define MMRGLOCK 0x20 /* Memory Mapped Register Gasket Lock */
-#define nMMRGLOCK 0x0
-#define FPGMEN 0x40 /* OTP/Fuse Program Enable */
-#define nFPGMEN 0x0
-
-/* Bit masks for OTP_TIMING */
-
-#define USECDIV 0xff /* Micro Second Divider */
-#define READACC 0x7f00 /* Read Access Time */
-#define CPUMPRL 0x38000 /* Charge Pump Release Time */
-#define CPUMPSU 0xc0000 /* Charge Pump Setup Time */
-#define CPUMPHD 0xf00000 /* Charge Pump Hold Time */
-#define PGMTIME 0xff000000 /* Program Time */
-
/* Bit masks for SECURE_SYSSWT */
#define EMUDABL 0x1 /* Emulation Disable. */
git.samba.org / sfrench / cifs-2.6.git / blobdiff