#define LATCH2_PIN_HOOKFLASH1 14
#define LATCH2_PIN_HOOKFLASH2 15
-static const struct gpio latch_gpios[] __initconst = {
- {
- .gpio = LATCH1_GPIO_BASE + 6,
- .flags = GPIOF_OUT_INIT_LOW,
- .label = "dockit1",
- },
- {
- .gpio = LATCH1_GPIO_BASE + 7,
- .flags = GPIOF_OUT_INIT_LOW,
- .label = "dockit2",
- },
- {
- .gpio = AMS_DELTA_GPIO_PIN_SCARD_RSTIN,
- .flags = GPIOF_OUT_INIT_LOW,
- .label = "scard_rstin",
- },
- {
- .gpio = AMS_DELTA_GPIO_PIN_SCARD_CMDVCC,
- .flags = GPIOF_OUT_INIT_LOW,
- .label = "scard_cmdvcc",
- },
- {
- .gpio = AMS_DELTA_LATCH2_GPIO_BASE + 14,
- .flags = GPIOF_OUT_INIT_LOW,
- .label = "hookflash1",
- },
- {
- .gpio = AMS_DELTA_LATCH2_GPIO_BASE + 15,
- .flags = GPIOF_OUT_INIT_LOW,
- .label = "hookflash2",
- },
-};
-
static struct regulator_consumer_supply modem_nreset_consumers[] = {
REGULATOR_SUPPLY("RESET#", "serial8250.1"),
REGULATOR_SUPPLY("POR", "cx20442-codec"),
static struct modem_private_data modem_priv;
-void ams_delta_latch_write(int base, int ngpio, u16 mask, u16 value)
-{
- int bit = 0;
- u16 bitpos = 1 << bit;
-
- for (; bit < ngpio; bit++, bitpos = bitpos << 1) {
- if (!(mask & bitpos))
- continue;
- else
- gpio_set_value(base + bit, (value & bitpos) != 0);
- }
-}
-EXPORT_SYMBOL(ams_delta_latch_write);
-
static struct resource ams_delta_nand_resources[] = {
[0] = {
.start = OMAP1_MPUIO_BASE,
{},
};
+static struct plat_serial8250_port ams_delta_modem_ports[];
+
+/*
+ * Obtain MODEM IRQ GPIO descriptor using its hardware pin
+ * number and assign related IRQ number to the MODEM port.
+ * Keep the GPIO descriptor open so nobody steps in.
+ */
+static void __init modem_assign_irq(struct gpio_chip *chip)
+{
+ struct gpio_desc *gpiod;
+
+ gpiod = gpiochip_request_own_desc(chip, AMS_DELTA_GPIO_PIN_MODEM_IRQ,
+ "modem_irq");
+ if (IS_ERR(gpiod)) {
+ pr_err("%s: modem IRQ GPIO request failed (%ld)\n", __func__,
+ PTR_ERR(gpiod));
+ } else {
+ gpiod_direction_input(gpiod);
+ ams_delta_modem_ports[0].irq = gpiod_to_irq(gpiod);
+ }
+}
+
/*
* The purpose of this function is to take care of proper initialization of
* devices and data structures which depend on GPIO lines provided by OMAP GPIO
return;
}
+ /*
+ * Start with FIQ initialization as it may have to request
+ * and release successfully each OMAP GPIO pin in turn.
+ */
ams_delta_init_fiq(chip, &ams_delta_serio_device);
+
+ modem_assign_irq(chip);
+}
+
+/*
+ * Initialize latch2 pins with values which are safe for dependent on-board
+ * devices or useful for their successull initialization even before GPIO
+ * driver takes control over the latch pins:
+ * - LATCH2_PIN_LCD_VBLEN = 0
+ * - LATCH2_PIN_LCD_NDISP = 0 Keep LCD device powered off before its
+ * driver takes control over it.
+ * - LATCH2_PIN_NAND_NCE = 0
+ * - LATCH2_PIN_NAND_NWP = 0 Keep NAND device down and write-
+ * protected before its driver takes
+ * control over it.
+ * - LATCH2_PIN_KEYBRD_PWR = 0 Keep keyboard powered off before serio
+ * driver takes control over it.
+ * - LATCH2_PIN_KEYBRD_DATAOUT = 0 Keep low to avoid corruption of first
+ * byte of data received from attached
+ * keyboard when serio device is probed;
+ * the pin is also hogged low by the latch2
+ * GPIO driver as soon as it is ready.
+ * - LATCH2_PIN_MODEM_NRESET = 1 Enable voice MODEM device, allowing for
+ * its successful probe even before a
+ * regulator it depends on, which in turn
+ * takes control over the pin, is set up.
+ * - LATCH2_PIN_MODEM_CODEC = 1 Attach voice MODEM CODEC data port
+ * to the MODEM so the CODEC is under
+ * control even if audio driver doesn't
+ * take it over.
+ */
+static void __init ams_delta_latch2_init(void)
+{
+ u16 latch2 = 1 << LATCH2_PIN_MODEM_NRESET | 1 << LATCH2_PIN_MODEM_CODEC;
+
+ __raw_writew(latch2, LATCH2_VIRT);
}
static void __init ams_delta_init(void)
omap_cfg_reg(J18_1610_CAM_D7);
omap_gpio_deps_init();
+ ams_delta_latch2_init();
gpiod_add_hogs(ams_delta_gpio_hogs);
omap_serial_init();
{
.membase = IOMEM(MODEM_VIRT),
.mapbase = MODEM_PHYS,
- .irq = -EINVAL, /* changed later */
+ .irq = IRQ_NOTCONNECTED, /* changed later */
.flags = UPF_BOOT_AUTOCONF,
.irqflags = IRQF_TRIGGER_RISING,
.iotype = UPIO_MEM,
static int __init ams_delta_gpio_init(void)
{
struct gpio_chip *chip;
- int err;
if (!machine_is_ams_delta())
return -ENODEV;
else
ams_delta_led_init(chip);
- err = gpio_request_array(latch_gpios, ARRAY_SIZE(latch_gpios));
- if (err)
- pr_err("Couldn't take over latch1/latch2 GPIO pins\n");
-
- return err;
+ return 0;
}
device_initcall_sync(ams_delta_gpio_init);
}
+/*
+ * This function expects MODEM IRQ number already assigned to the port.
+ * The MODEM device requires its RESET# pin kept high during probe.
+ * That requirement can be fulfilled in several ways:
+ * - with a descriptor of already functional modem_nreset regulator
+ * assigned to the MODEM private data,
+ * - with the regulator not yet controlled by modem_pm function but
+ * already enabled by default on probe,
+ * - before the modem_nreset regulator is probed, with the pin already
+ * set high explicitly.
+ * The last one is already guaranteed by ams_delta_latch2_init() called
+ * from machine_init.
+ * In order to avoid taking over ttyS0 device slot, the MODEM device
+ * should be registered after OMAP serial ports. Since those ports
+ * are registered at arch_initcall, this function can be called safely
+ * at arch_initcall_sync earliest.
+ */
static int __init ams_delta_modem_init(void)
{
int err;
- omap_cfg_reg(M14_1510_GPIO2);
- ams_delta_modem_ports[0].irq =
- gpio_to_irq(AMS_DELTA_GPIO_PIN_MODEM_IRQ);
+ if (!machine_is_ams_delta())
+ return -ENODEV;
- err = gpio_request(AMS_DELTA_GPIO_PIN_MODEM_IRQ, "modem");
- if (err) {
- pr_err("Couldn't request gpio pin for modem\n");
- return err;
- }
- gpio_direction_input(AMS_DELTA_GPIO_PIN_MODEM_IRQ);
+ omap_cfg_reg(M14_1510_GPIO2);
/* Initialize the modem_nreset regulator consumer before use */
modem_priv.regulator = ERR_PTR(-ENODEV);
- ams_delta_latch2_write(AMS_DELTA_LATCH2_MODEM_CODEC,
- AMS_DELTA_LATCH2_MODEM_CODEC);
-
err = platform_device_register(&ams_delta_modem_device);
- if (err)
- gpio_free(AMS_DELTA_GPIO_PIN_MODEM_IRQ);
return err;
}
+arch_initcall_sync(ams_delta_modem_init);
static int __init late_init(void)
{
if (err)
return err;
- err = ams_delta_modem_init();
- if (err)
- return err;
-
/*
* Once the modem device is registered, the modem_nreset
* regulator can be requested on behalf of that device.
unregister:
platform_device_unregister(&ams_delta_modem_device);
- gpio_free(AMS_DELTA_GPIO_PIN_MODEM_IRQ);
return err;
}
git.samba.org / sfrench / cifs-2.6.git / blobdiff