default y
select HAVE_AOUT
select HAVE_IDE
+ select HAVE_MEMBLOCK
select RTC_LIB
select SYS_SUPPORTS_APM_EMULATION
select GENERIC_ATOMIC64 if (!CPU_32v6K)
config GENERIC_CLOCKEVENTS_BROADCAST
bool
depends on GENERIC_CLOCKEVENTS
- default y if SMP && !LOCAL_TIMERS
+ default y if SMP
config HAVE_TCM
bool
help
Support for Intel's IXP4XX (XScale) family of processors.
-config ARCH_L7200
- bool "LinkUp-L7200"
- select CPU_ARM720T
- select FIQ
- select ARCH_USES_GETTIMEOFFSET
- help
- Say Y here if you intend to run this kernel on a LinkUp Systems
- L7200 Software Development Board which uses an ARM720T processor.
- Information on this board can be obtained at:
-
- <http://www.linkupsys.com/>
-
- If you have any questions or comments about the Linux kernel port
- to this board, send e-mail to <sjhill@cotw.com>.
-
config ARCH_DOVE
bool "Marvell Dove"
select PCI
config ARCH_LH7A40X
bool "Sharp LH7A40X"
select CPU_ARM922T
- select ARCH_DISCONTIGMEM_ENABLE if !LH7A40X_CONTIGMEM
select ARCH_SPARSEMEM_ENABLE if !LH7A40X_CONTIGMEM
select ARCH_USES_GETTIMEOFFSET
help
config LOCAL_TIMERS
bool "Use local timer interrupts"
depends on SMP && (REALVIEW_EB_ARM11MP || MACH_REALVIEW_PB11MP || \
- REALVIEW_EB_A9MP || MACH_REALVIEW_PBX || ARCH_OMAP4 || ARCH_U8500)
+ REALVIEW_EB_A9MP || MACH_REALVIEW_PBX || ARCH_OMAP4 || \
+ ARCH_U8500 || ARCH_VEXPRESS_CA9X4)
default y
- select HAVE_ARM_TWD if (ARCH_REALVIEW || ARCH_OMAP4 || ARCH_U8500)
+ select HAVE_ARM_TWD if (ARCH_REALVIEW || ARCH_VEXPRESS || ARCH_OMAP4 || ARCH_U8500)
help
Enable support for local timers on SMP platforms, rather then the
legacy IPI broadcast method. Local timers allows the system
config HZ
int
- default 128 if ARCH_L7200
default 200 if ARCH_EBSA110 || ARCH_S3C2410 || ARCH_S5P6440 || ARCH_S5P6442 || ARCH_S5PV210
default OMAP_32K_TIMER_HZ if ARCH_OMAP && OMAP_32K_TIMER
default AT91_TIMER_HZ if ARCH_AT91
+ default SHMOBILE_TIMER_HZ if ARCH_SHMOBILE
default 100
config THUMB2_KERNEL
config ARCH_HAS_HOLES_MEMORYMODEL
bool
-# Discontigmem is deprecated
-config ARCH_DISCONTIGMEM_ENABLE
- bool
-
config ARCH_SPARSEMEM_ENABLE
bool
def_bool ARCH_SPARSEMEM_ENABLE
config ARCH_SELECT_MEMORY_MODEL
- def_bool ARCH_DISCONTIGMEM_ENABLE && ARCH_SPARSEMEM_ENABLE
-
-config NODES_SHIFT
- int
- default "4" if ARCH_LH7A40X
- default "2"
- depends on NEED_MULTIPLE_NODES
+ def_bool ARCH_SPARSEMEM_ENABLE
config HIGHMEM
bool "High Memory Support (EXPERIMENTAL)"
disabled, perf events will use software events only.
config SPARSE_IRQ
- bool "Support sparse irq numbering"
- depends on EXPERIMENTAL
+ def_bool n
help
This enables support for sparse irqs. This is useful in general
as most CPUs have a fairly sparse array of IRQ vectors, which
number of off-chip IRQs will want to treat this as
experimental until they have been independently verified.
- If you don't know what to do here, say N.
-
source "mm/Kconfig"
config FORCE_MAX_ZONEORDER