bzip2 -dc linux-3.X.tar.bz2 | tar xvf -
- Replace "XX" with the version number of the latest kernel.
+ Replace "X" with the version number of the latest kernel.
Do NOT use the /usr/src/linux area! This area has a (usually
incomplete) set of kernel headers that are used by the library header
- You can also upgrade between 3.x releases by patching. Patches are
distributed in the traditional gzip and the newer bzip2 format. To
install by patching, get all the newer patch files, enter the
- top level directory of the kernel source (linux-3.x) and execute:
+ top level directory of the kernel source (linux-3.X) and execute:
gzip -cd ../patch-3.x.gz | patch -p1
or
bzip2 -dc ../patch-3.x.bz2 | patch -p1
- (repeat xx for all versions bigger than the version of your current
- source tree, _in_order_) and you should be ok. You may want to remove
- the backup files (xxx~ or xxx.orig), and make sure that there are no
- failed patches (xxx# or xxx.rej). If there are, either you or me has
- made a mistake.
+ Replace "x" for all versions bigger than the version "X" of your current
+ source tree, _in_order_, and you should be ok. You may want to remove
+ the backup files (some-file-name~ or some-file-name.orig), and make sure
+ that there are no failed patches (some-file-name# or some-file-name.rej).
+ If there are, either you or I have made a mistake.
Unlike patches for the 3.x kernels, patches for the 3.x.y kernels
(also known as the -stable kernels) are not incremental but instead apply
BUILD directory for the kernel:
- When compiling the kernel all output files will per default be
+ When compiling the kernel, all output files will per default be
stored together with the kernel source code.
Using the option "make O=output/dir" allow you to specify an alternate
place for the output files (including .config).
Example:
- kernel source code: /usr/src/linux-3.N
+ kernel source code: /usr/src/linux-3.X
build directory: /home/name/build/kernel
- To configure and build the kernel use:
- cd /usr/src/linux-3.N
+ To configure and build the kernel, use:
+ cd /usr/src/linux-3.X
make O=/home/name/build/kernel menuconfig
make O=/home/name/build/kernel
sudo make O=/home/name/build/kernel modules_install install
- Please note: If the 'O=output/dir' option is used then it must be
+ Please note: If the 'O=output/dir' option is used, then it must be
used for all invocations of make.
CONFIGURING the kernel:
new version with minimal work, use "make oldconfig", which will
only ask you for the answers to new questions.
- - Alternate configuration commands are:
+ - Alternative configuration commands are:
"make config" Plain text interface.
"make menuconfig" Text based color menus, radiolists & dialogs.
"make nconfig" Enhanced text based color menus.
possible to do "make install" if you have lilo installed to suit the
kernel makefiles, but you may want to check your particular lilo setup first.
- To do the actual install you have to be root, but none of the normal
+ To do the actual install, you have to be root, but none of the normal
build should require that. Don't take the name of root in vain.
- If you configured any of the parts of the kernel as `modules', you
- Verbose kernel compile/build output:
- Normally the kernel build system runs in a fairly quiet mode (but not
+ Normally, the kernel build system runs in a fairly quiet mode (but not
totally silent). However, sometimes you or other kernel developers need
to see compile, link, or other commands exactly as they are executed.
For this, use "verbose" build mode. This is done by inserting
- Booting a kernel directly from a floppy without the assistance of a
bootloader such as LILO, is no longer supported.
- If you boot Linux from the hard drive, chances are you use LILO which
+ If you boot Linux from the hard drive, chances are you use LILO, which
uses the kernel image as specified in the file /etc/lilo.conf. The
kernel image file is usually /vmlinuz, /boot/vmlinuz, /bzImage or
/boot/bzImage. To use the new kernel, save a copy of the old image
incomprehensible to you, but it does contain information that may
help debugging the problem. The text above the dump is also
important: it tells something about why the kernel dumped code (in
- the above example it's due to a bad kernel pointer). More information
+ the above example, it's due to a bad kernel pointer). More information
on making sense of the dump is in Documentation/oops-tracing.txt
- If you compiled the kernel with CONFIG_KALLSYMS you can send the dump
sense of the dump (but compiling with CONFIG_KALLSYMS is usually preferred).
This utility can be downloaded from
ftp://ftp.<country>.kernel.org/pub/linux/utils/kernel/ksymoops/ .
- Alternately you can do the dump lookup by hand:
+ Alternatively, you can do the dump lookup by hand:
- In debugging dumps like the above, it helps enormously if you can
look up what the EIP value means. The hex value as such doesn't help
kernel image or similar), telling me as much about your setup as
possible will help. Please read the REPORTING-BUGS document for details.
- - Alternately, you can use gdb on a running kernel. (read-only; i.e. you
+ - Alternatively, you can use gdb on a running kernel. (read-only; i.e. you
cannot change values or set break points.) To do this, first compile the
kernel with -g; edit arch/i386/Makefile appropriately, then do a "make
clean". You'll also need to enable CONFIG_PROC_FS (via "make config").
git.samba.org / sfrench / cifs-2.6.git / blobdiff