- Default: 1
- For auto-loading more than one card, specify this
option together with snd-card-X aliases.
-
+ slots - Reserve the slot index for the given driver.
+ This option takes multiple strings.
+ See "Module Autoloading Support" section for details.
Module snd-pcm-oss
------------------
Module for sound cards based on Analog Devices AD1816A/AD1815 ISA chips.
- port - port # for AD1816A chip (PnP setup)
- mpu_port - port # for MPU-401 UART (PnP setup)
- fm_port - port # for OPL3 (PnP setup)
- irq - IRQ # for AD1816A chip (PnP setup)
- mpu_irq - IRQ # for MPU-401 UART (PnP setup)
- dma1 - first DMA # for AD1816A chip (PnP setup)
- dma2 - second DMA # for AD1816A chip (PnP setup)
clockfreq - Clock frequency for AD1816A chip (default = 0, 33000Hz)
This module supports multiple cards, autoprobe and PnP.
Module for sound cards based on Avance Logic ALS100/ALS120 ISA chips.
- port - port # for ALS100 (SB16) chip (PnP setup)
- irq - IRQ # for ALS100 (SB16) chip (PnP setup)
- dma8 - 8-bit DMA # for ALS100 (SB16) chip (PnP setup)
- dma16 - 16-bit DMA # for ALS100 (SB16) chip (PnP setup)
- mpu_port - port # for MPU-401 UART (PnP setup)
- mpu_irq - IRQ # for MPU-401 (PnP setup)
- fm_port - port # for OPL3 FM (PnP setup)
-
This module supports multiple cards, autoprobe and PnP.
The power-management is supported.
Module for sound cards based on Aztech System AZT2320 ISA chip (PnP only).
- port - port # for AZT2320 chip (PnP setup)
- wss_port - port # for WSS (PnP setup)
- mpu_port - port # for MPU-401 UART (PnP setup)
- fm_port - FM port # for AZT2320 chip (PnP setup)
- irq - IRQ # for AZT2320 (WSS) chip (PnP setup)
- mpu_irq - IRQ # for MPU-401 UART (PnP setup)
- dma1 - 1st DMA # for AZT2320 (WSS) chip (PnP setup)
- dma2 - 2nd DMA # for AZT2320 (WSS) chip (PnP setup)
-
This module supports multiple cards, PnP and autoprobe.
The power-management is supported.
Module for sound cards based on C-Media CMI8330 ISA chips.
+ isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
+
+ with isapnp=0, the following options are available:
+
wssport - port # for CMI8330 chip (WSS)
wssirq - IRQ # for CMI8330 chip (WSS)
wssdma - first DMA # for CMI8330 chip (WSS)
Module snd-cmipci
-----------------
- Module for C-Media CMI8338 and 8738 PCI sound cards.
+ Module for C-Media CMI8338/8738/8768/8770 PCI sound cards.
- mpu_port - 0x300,0x310,0x320,0x330 = legacy port,
- 1 = integrated PCI port,
+ mpu_port - port address of MIDI interface (8338 only):
+ 0x300,0x310,0x320,0x330 = legacy port,
0 = disable (default)
- fm_port - 0x388 = legacy port,
- 1 = integrated PCI port (default),
+ fm_port - port address of OPL-3 FM synthesizer (8x38 only):
+ 0x388 = legacy port,
+ 1 = integrated PCI port (default on 8738),
0 = disable
soft_ac3 - Software-conversion of raw SPDIF packets (model 033 only)
(default = 1)
Module for sound cards based on CS4232/CS4232A ISA chips.
+ isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
+
+ with isapnp=0, the following options are available:
+
port - port # for CS4232 chip (PnP setup - 0x534)
cport - control port # for CS4232 chip (PnP setup - 0x120,0x210,0xf00)
mpu_port - port # for MPU-401 UART (PnP setup - 0x300), -1 = disable
mpu_irq - IRQ # for MPU-401 UART (9,11,12,15)
dma1 - first DMA # for CS4232 chip (0,1,3)
dma2 - second DMA # for Yamaha CS4232 chip (0,1,3), -1 = disable
- isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
This module supports multiple cards. This module does not support autoprobe
- thus main port must be specified!!! Other ports are optional.
+ (if ISA PnP is not used) thus main port must be specified!!! Other ports are
+ optional.
The power-management is supported.
Module for sound cards based on CS4235/CS4236/CS4236B/CS4237B/
CS4238B/CS4239 ISA chips.
+ isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
+
+ with isapnp=0, the following options are available:
+
port - port # for CS4236 chip (PnP setup - 0x534)
cport - control port # for CS4236 chip (PnP setup - 0x120,0x210,0xf00)
mpu_port - port # for MPU-401 UART (PnP setup - 0x300), -1 = disable
mpu_irq - IRQ # for MPU-401 UART (9,11,12,15)
dma1 - first DMA # for CS4236 chip (0,1,3)
dma2 - second DMA # for CS4236 chip (0,1,3), -1 = disable
- isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
This module supports multiple cards. This module does not support autoprobe
(if ISA PnP is not used) thus main port and control port must be
Module for Diamond Technologies DT-019X / Avance Logic ALS-007 (PnP
only)
- port - Port # (PnP setup)
- mpu_port - Port # for MPU-401 (PnP setup)
- fm_port - Port # for FM OPL-3 (PnP setup)
- irq - IRQ # (PnP setup)
- mpu_irq - IRQ # for MPU-401 (PnP setup)
- dma8 - DMA # (PnP setup)
-
This module supports multiple cards. This module is enabled only with
ISA PnP support.
Module for sound cards based on ESS ES968 chip (PnP only).
- port - port # for ES968 (SB8) chip (PnP setup)
- irq - IRQ # for ES968 (SB8) chip (PnP setup)
- dma1 - DMA # for ES968 (SB8) chip (PnP setup)
-
This module supports multiple cards, PnP and autoprobe.
The power-management is supported.
Module for ESS AudioDrive ES-18xx sound cards.
+ isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
+
+ with isapnp=0, the following options are available:
+
port - port # for ES-18xx chip (0x220,0x240,0x260)
mpu_port - port # for MPU-401 port (0x300,0x310,0x320,0x330), -1 = disable (default)
fm_port - port # for FM (optional, not used)
irq - IRQ # for ES-18xx chip (5,7,9,10)
dma1 - first DMA # for ES-18xx chip (0,1,3)
dma2 - first DMA # for ES-18xx chip (0,1,3)
- isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
This module supports multiple cards, ISA PnP and autoprobe (without MPU-401
port if native ISA PnP routines are not used).
VIA VT8251/VT8237A,
SIS966, ULI M5461
+ [Multiple options for each card instance]
model - force the model name
position_fix - Fix DMA pointer (0 = auto, 1 = none, 2 = POSBUF, 3 = FIFO size)
probe_mask - Bitmask to probe codecs (default = -1, meaning all slots)
+
+ [Single (global) options]
single_cmd - Use single immediate commands to communicate with
codecs (for debugging only)
enable_msi - Enable Message Signaled Interrupt (MSI) (default = off)
power_save - Automatic power-saving timtout (in second, 0 =
- disable, default = 10)
+ disable)
power_save_controller - Reset HD-audio controller in power-saving mode
(default = on)
- This module supports one card and autoprobe.
-
+ This module supports multiple cards and autoprobe.
+
Each codec may have a model table for different configurations.
If your machine isn't listed there, the default (usually minimal)
configuration is set up. You can pass "model=<name>" option to
will Will laptops (PB V7900)
replacer Replacer 672V
basic fixed pin assignment (old default model)
+ test for testing/debugging purpose, almost all controls can
+ adjusted. Appearing only when compiled with
+ $CONFIG_SND_DEBUG=y
auto auto-config reading BIOS (default)
ALC262
fujitsu Fujitsu Laptop
hp-bpc HP xw4400/6400/8400/9400 laptops
hp-bpc-d7000 HP BPC D7000
+ hp-tc-t5735 HP Thin Client T5735
+ hp-rp5700 HP RP5700
benq Benq ED8
benq-t31 Benq T31
hippo Hippo (ATI) with jack detection, Sony UX-90s
hippo_1 Hippo (Benq) with jack detection
sony-assamd Sony ASSAMD
+ ultra Samsung Q1 Ultra Vista model
basic fixed pin assignment w/o SPDIF
auto auto-config reading BIOS (default)
3stack 3-stack model
toshiba Toshiba A205
acer Acer laptops
+ dell Dell OEM laptops (Vostro 1200)
+ test for testing/debugging purpose, almost all controls can
+ adjusted. Appearing only when compiled with
+ $CONFIG_SND_DEBUG=y
auto auto-config reading BIOS (default)
ALC662
3stack-6ch-dig 3-stack (6-channel) with SPDIF
6stack-dig 6-stack with SPDIF
lenovo-101e Lenovo laptop
+ eeepc-p701 ASUS Eeepc P701
+ eeepc-ep20 ASUS Eeepc EP20
auto auto-config reading BIOS (default)
ALC882/885
3stack-dig 3-jack with SPDIF I/O
6stack-dig 6-jack digital with SPDIF I/O
arima Arima W820Di1
+ targa Targa T8, MSI-1049 T8
+ asus-a7j ASUS A7J
+ asus-a7m ASUS A7M
macpro MacPro support
mbp3 Macbook Pro rev3
imac24 iMac 24'' with jack detection
lenovo-101e Lenovo 101E
lenovo-nb0763 Lenovo NB0763
lenovo-ms7195-dig Lenovo MS7195
+ haier-w66 Haier W66
6stack-hp HP machines with 6stack (Nettle boards)
3stack-hp HP machines with 3stack (Lucknow, Samba boards)
+ 6stack-dell Dell machines with 6stack (Inspiron 530)
+ mitac Mitac 8252D
auto auto-config reading BIOS (default)
ALC861/660
AD1984
basic default configuration
thinkpad Lenovo Thinkpad T61/X61
+ dell Dell T3400
AD1986A
6stack 6-jack, separate surrounds (default)
3stack 3-stack, shared surrounds
laptop 2-channel only (FSC V2060, Samsung M50)
laptop-eapd 2-channel with EAPD (Samsung R65, ASUS A6J)
+ laptop-automute 2-channel with EAPD and HP-automute (Lenovo N100)
ultra 2-channel with EAPD (Samsung Ultra tablet PC)
AD1988
auto auto-config reading BIOS (default)
Conexant 5045
- laptop Laptop config
+ laptop-hpsense Laptop with HP sense (old model laptop)
+ laptop-micsense Laptop with Mic sense (old model fujitsu)
+ laptop-hpmicsense Laptop with HP and Mic senses
+ benq Benq R55E
test for testing/debugging purpose, almost all controls
can be adjusted. Appearing only when compiled with
$CONFIG_SND_DEBUG=y
can be adjusted. Appearing only when compiled with
$CONFIG_SND_DEBUG=y
- STAC9200/9205/9254
+ Conexant 5051
+ laptop Basic Laptop config (default)
+ hp HP Spartan laptop
+
+ STAC9200
ref Reference board
+ dell-d21 Dell (unknown)
+ dell-d22 Dell (unknown)
+ dell-d23 Dell (unknown)
+ dell-m21 Dell Inspiron 630m, Dell Inspiron 640m
+ dell-m22 Dell Latitude D620, Dell Latitude D820
+ dell-m23 Dell XPS M1710, Dell Precision M90
+ dell-m24 Dell Latitude 120L
+ dell-m25 Dell Inspiron E1505n
+ dell-m26 Dell Inspiron 1501
+ dell-m27 Dell Inspiron E1705/9400
+ gateway Gateway laptops with EAPD control
+
+ STAC9205/9254
+ ref Reference board
+ dell-m42 Dell (unknown)
dell-m43 Dell Precision
dell-m44 Dell Inspiron
ref Reference board
3stack D945 3stack
5stack D945 5stack + SPDIF
- dell Dell XPS M1210
intel-mac-v1 Intel Mac Type 1
intel-mac-v2 Intel Mac Type 2
intel-mac-v3 Intel Mac Type 3
macbook-pro Intel Mac Book Pro 2nd generation (eq. type 3)
imac-intel Intel iMac (eq. type 2)
imac-intel-20 Intel iMac (newer version) (eq. type 3)
+ dell-d81 Dell (unknown)
+ dell-d82 Dell (unknown)
+ dell-m81 Dell (unknown)
+ dell-m82 Dell XPS M1210
STAC9202/9250/9251
ref Reference board, base config
ref Reference board
3stack D965 3stack
5stack D965 5stack + SPDIF
- dell-3stack Dell E520
+ dell-3stack Dell Dimension E520
STAC9872
vaio Setup for VAIO FE550G/SZ110
subsystem ID (output of "lspci -nv") to ALSA BTS or alsa-devel
ML (see the section "Links and Addresses").
- When CONFIG_SND_HDA_POWER_SAVE is set, two options, power_save and
- power_save_controller become available. power_save specifies the
- time to turn off the power automatically at idle status. When
- power_save_controller is true, the controller is also turned off.
- This might result in more obvious click noise at turning on/off.
+ power_save and power_save_controller options are for power-saving
+ mode. See powersave.txt for details.
Note 2: If you get click noises on output, try the module option
position_fix=1 or 2. position_fix=1 will use the SD_LPIB
See hdspm.txt for details.
+ Module snd-hifier
+ -----------------
+
+ Module for the MediaTek/TempoTec HiFier Fantasia sound card.
+
+ This module supports autoprobe and multiple cards.
+
+ Power management is _not_ supported.
+
Module snd-ice1712
------------------
* Chaintech 9CJS
* Chaintech AV-710
* Shuttle SN25P
+ * Onkyo SE-90PCI
+ * Onkyo SE-200PCI
model - Use the given board model, one of the following:
revo51, revo71, amp2000, prodigy71, prodigy71lt,
prodigy192, aureon51, aureon71, universe, ap192,
- k8x800, phase22, phase28, ms300, av710
+ k8x800, phase22, phase28, ms300, av710, se200pci,
+ se90pci
This module supports multiple cards and autoprobe.
Module for Gravis UltraSound PnP, Dynasonic 3-D/Pro, STB Sound Rage 32
and other sound cards based on AMD InterWave (tm) chip.
- port - port # for InterWave chip (0x210,0x220,0x230,0x240,0x250,0x260)
- irq - IRQ # for InterWave chip (3,5,9,11,12,15)
- dma1 - DMA # for InterWave chip (0,1,3,5,6,7)
- dma2 - DMA # for InterWave chip (0,1,3,5,6,7,-1=disable)
joystick_dac - 0 to 31, (0.59V-4.52V or 0.389V-2.98V)
midi - 1 = MIDI UART enable, 0 = MIDI UART disable (default)
pcm_voices - reserved PCM voices for the synthesizer (default 2)
effect - 1 = InterWave effects enable (default 0);
requires 8 voices
+ isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
+
+ with isapnp=0, the following options are available:
+
+ port - port # for InterWave chip (0x210,0x220,0x230,0x240,0x250,0x260)
+ irq - IRQ # for InterWave chip (3,5,9,11,12,15)
+ dma1 - DMA # for InterWave chip (0,1,3,5,6,7)
+ dma2 - DMA # for InterWave chip (0,1,3,5,6,7,-1=disable)
This module supports multiple cards, autoprobe and ISA PnP.
and other sound cards based on AMD InterWave (tm) chip with TEA6330T
circuit for extended control of bass, treble and master volume.
- port - port # for InterWave chip (0x210,0x220,0x230,0x240,0x250,0x260)
- port_tc - tone control (i2c bus) port # for TEA6330T chip (0x350,0x360,0x370,0x380)
- irq - IRQ # for InterWave chip (3,5,9,11,12,15)
- dma1 - DMA # for InterWave chip (0,1,3,5,6,7)
- dma2 - DMA # for InterWave chip (0,1,3,5,6,7,-1=disable)
joystick_dac - 0 to 31, (0.59V-4.52V or 0.389V-2.98V)
midi - 1 = MIDI UART enable, 0 = MIDI UART disable (default)
pcm_voices - reserved PCM voices for the synthesizer (default 2)
effect - 1 = InterWave effects enable (default 0);
requires 8 voices
+ isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
+
+ with isapnp=0, the following options are available:
+
+ port - port # for InterWave chip (0x210,0x220,0x230,0x240,0x250,0x260)
+ port_tc - tone control (i2c bus) port # for TEA6330T chip (0x350,0x360,0x370,0x380)
+ irq - IRQ # for InterWave chip (3,5,9,11,12,15)
+ dma1 - DMA # for InterWave chip (0,1,3,5,6,7)
+ dma2 - DMA # for InterWave chip (0,1,3,5,6,7,-1=disable)
This module supports multiple cards, autoprobe and ISA PnP.
port - port number or -1 (disable)
irq - IRQ number or -1 (disable)
pnp - PnP detection - 0 = disable, 1 = enable (default)
- uart_enter - Issue UART_ENTER command at open - bool, default = on
This module supports multiple devices and PnP.
Module for Yamaha OPL3-SA2/SA3 sound cards.
+ isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
+
+ with isapnp=0, the following options are available:
+
port - control port # for OPL3-SA chip (0x370)
sb_port - SB port # for OPL3-SA chip (0x220,0x240)
wss_port - WSS port # for OPL3-SA chip (0x530,0xe80,0xf40,0x604)
irq - IRQ # for OPL3-SA chip (5,7,9,10)
dma1 - first DMA # for Yamaha OPL3-SA chip (0,1,3)
dma2 - second DMA # for Yamaha OPL3-SA chip (0,1,3), -1 = disable
- isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
This module supports multiple cards and ISA PnP. It does not support
autoprobe (if ISA PnP is not used) thus all ports must be specified!!!
Module for sound cards based on OPTi 82c92x and Analog Devices AD1848 chips.
Module works with OAK Mozart cards as well.
+ isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
+
+ with isapnp=0, the following options are available:
+
port - port # for WSS chip (0x530,0xe80,0xf40,0x604)
mpu_port - port # for MPU-401 UART (0x300,0x310,0x320,0x330)
fm_port - port # for OPL3 device (0x388)
Module for sound cards based on OPTi 82c92x and Crystal CS4231 chips.
+ isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
+
+ with isapnp=0, the following options are available:
+
port - port # for WSS chip (0x530,0xe80,0xf40,0x604)
mpu_port - port # for MPU-401 UART (0x300,0x310,0x320,0x330)
fm_port - port # for OPL3 device (0x388)
Module for sound cards based on OPTi 82c93x chips.
+ isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
+
+ with isapnp=0, the following options are available:
+
port - port # for WSS chip (0x530,0xe80,0xf40,0x604)
mpu_port - port # for MPU-401 UART (0x300,0x310,0x320,0x330)
fm_port - port # for OPL3 device (0x388)
This module supports only one card, autoprobe and PnP.
+ Module snd-oxygen
+ -----------------
+
+ Module for sound cards based on the C-Media CMI8788 chip:
+ * Asound A-8788
+ * AuzenTech X-Meridian
+ * Bgears b-Enspirer
+ * Club3D Theatron DTS
+ * HT-Omega Claro
+ * Razer Barracuda AC-1
+ * Sondigo Inferno
+
+ This module supports autoprobe and multiple cards.
+
+ Power management is _not_ supported.
+
Module snd-pcxhr
----------------
SoundBlaster AWE 32 (PnP),
SoundBlaster AWE 64 PnP
+ mic_agc - Mic Auto-Gain-Control - 0 = disable, 1 = enable (default)
+ csp - ASP/CSP chip support - 0 = disable (default), 1 = enable
+ isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
+
+ with isapnp=0, the following options are available:
+
port - port # for SB DSP 4.x chip (0x220,0x240,0x260)
mpu_port - port # for MPU-401 UART (0x300,0x330), -1 = disable
awe_port - base port # for EMU8000 synthesizer (0x620,0x640,0x660)
irq - IRQ # for SB DSP 4.x chip (5,7,9,10)
dma8 - 8-bit DMA # for SB DSP 4.x chip (0,1,3)
dma16 - 16-bit DMA # for SB DSP 4.x chip (5,6,7)
- mic_agc - Mic Auto-Gain-Control - 0 = disable, 1 = enable (default)
- csp - ASP/CSP chip support - 0 = disable (default), 1 = enable
- isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
This module supports multiple cards, autoprobe and ISA PnP.
The power-management is supported.
+ Module snd-sc6000
+ -----------------
+
+ Module for Gallant SC-6000 soundcard.
+
+ port - Port # (0x220 or 0x240)
+ mss_port - MSS Port # (0x530 or 0xe80)
+ irq - IRQ # (5,7,9,10,11)
+ mpu_irq - MPU-401 IRQ # (5,7,9,10) ,0 - no MPU-401 irq
+ dma - DMA # (1,3,0)
+
+ This module supports multiple cards.
+
+ This card is also known as Audio Excel DSP 16 or Zoltrix AV302.
+
Module snd-sgalaxy
------------------
Module for ENSONIQ SoundScape PnP cards.
port - Port # (PnP setup)
+ wss_port - WSS Port # (PnP setup)
irq - IRQ # (PnP setup)
mpu_irq - MPU-401 IRQ # (PnP setup)
dma - DMA # (PnP setup)
+ dma2 - 2nd DMA # (PnP setup, -1 to disable)
This module supports multiple cards. ISA PnP must be enabled.
You need sscape_ctl tool in alsa-tools package for loading
Module for Turtle Beach Maui, Tropez and Tropez+ sound cards.
+ use_cs4232_midi - Use CS4232 MPU-401 interface
+ (inaccessibly located inside your computer)
+ isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
+
+ with isapnp=0, the following options are available:
+
cs4232_pcm_port - Port # for CS4232 PCM interface.
cs4232_pcm_irq - IRQ # for CS4232 PCM interface (5,7,9,11,12,15).
cs4232_mpu_port - Port # for CS4232 MPU-401 interface.
cs4232_mpu_irq - IRQ # for CS4232 MPU-401 interface (9,11,12,15).
- use_cs4232_midi - Use CS4232 MPU-401 interface
- (inaccessibly located inside your computer)
ics2115_port - Port # for ICS2115
ics2115_irq - IRQ # for ICS2115
fm_port - FM OPL-3 Port #
dma1 - DMA1 # for CS4232 PCM interface.
dma2 - DMA2 # for CS4232 PCM interface.
- isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
+
+ The below are options for wavefront_synth features:
+ wf_raw - Assume that we need to boot the OS (default:no)
+ If yes, then during driver loading, the state of the board is
+ ignored, and we reset the board and load the firmware anyway.
+ fx_raw - Assume that the FX process needs help (default:yes)
+ If false, we'll leave the FX processor in whatever state it is
+ when the driver is loaded. The default is to download the
+ microprogram and associated coefficients to set it up for
+ "default" operation, whatever that means.
+ debug_default - Debug parameters for card initialization
+ wait_usecs - How long to wait without sleeping, usecs
+ (default:150)
+ This magic number seems to give pretty optimal throughput
+ based on my limited experimentation.
+ If you want to play around with it and find a better value, be
+ my guest. Remember, the idea is to get a number that causes us
+ to just busy wait for as many WaveFront commands as possible,
+ without coming up with a number so large that we hog the whole
+ CPU.
+ Specifically, with this number, out of about 134,000 status
+ waits, only about 250 result in a sleep.
+ sleep_interval - How long to sleep when waiting for reply
+ (default: 100)
+ sleep_tries - How many times to try sleeping during a wait
+ (default: 50)
+ ospath - Pathname to processed ICS2115 OS firmware
+ (default:wavefront.os)
+ The path name of the ISC2115 OS firmware. In the recent
+ version, it's handled via firmware loader framework, so it
+ must be installed in the proper path, typically,
+ /lib/firmware.
+ reset_time - How long to wait for a reset to take effect
+ (default:2)
+ ramcheck_time - How many seconds to wait for the RAM test
+ (default:20)
+ osrun_time - How many seconds to wait for the ICS2115 OS
+ (default:10)
This module supports multiple cards and ISA PnP.
+ Note: the firmware file "wavefront.os" was located in the earlier
+ version in /etc. Now it's loaded via firmware loader, and
+ must be in the proper firmware path, such as /lib/firmware.
+ Copy (or symlink) the file appropriately if you get an error
+ regarding firmware downloading after upgrading the kernel.
+
Module snd-sonicvibes
---------------------
This module supports multiple cards.
+ Module snd-virtuoso
+ -------------------
+
+ Module for sound cards based on the Asus AV200 chip, i.e.,
+ Xonar D2 and Xonar D2X.
+
+ This module supports autoprobe and multiple cards.
+
+ Power management is _not_ supported.
+
Module snd-vx222
----------------
In this example, the interwave card is always loaded as the first card
(index 0) and ens1371 as the second (index 1).
+Alternative (and new) way to fixate the slot assignment is to use
+"slots" option of snd module. In the case above, specify like the
+following:
+
+options snd slots=snd-interwave,snd-ens1371
+
+Then, the first slot (#0) is reserved for snd-interwave driver, and
+the second (#1) for snd-ens1371. You can omit index option in each
+driver if slots option is used (although you can still have them at
+the same time as long as they don't conflict).
+
+The slots option is especially useful for avoiding the possible
+hot-plugging and the resultant slot conflict. For example, in the
+case above again, the first two slots are already reserved. If any
+other driver (e.g. snd-usb-audio) is loaded before snd-interwave or
+snd-ens1371, it will be assigned to the third or later slot.
+
ALSA PCM devices to OSS devices mapping
=======================================
git.samba.org / sfrench / cifs-2.6.git / blobdiff