strict -- Be less tolerant of platforms that are not
strictly ACPI specification compliant.
- See also Documentation/pm.txt, pci=noacpi
+ See also Documentation/power/pm.txt, pci=noacpi
acpi_apic_instance= [ACPI, IOAPIC]
Format: <int>
default: 0
acpi_sleep= [HW,ACPI] Sleep options
- Format: { s3_bios, s3_mode }
- See Documentation/power/video.txt
+ Format: { s3_bios, s3_mode, s3_beep }
+ See Documentation/power/video.txt for s3_bios and s3_mode.
+ s3_beep is for debugging; it makes the PC's speaker beep
+ as soon as the kernel's real-mode entry point is called.
acpi_sci= [HW,ACPI] ACPI System Control Interrupt trigger mode
Format: { level | edge | high | low }
Format: <cyl>,<head>,<sect>
hd?= [HW] (E)IDE subsystem
- hd?lun= See Documentation/ide.txt.
+ hd?lun= See Documentation/ide/ide.txt.
highmem=nn[KMG] [KNL,BOOT] forces the highmem zone to have an exact
size of <nn>. This works even on boxes that have no
(Don't attempt to blink the leds)
i8042.noaux [HW] Don't check for auxiliary (== mouse) port
i8042.nokbd [HW] Don't check/create keyboard port
+ i8042.noloop [HW] Disable the AUX Loopback command while probing
+ for the AUX port
i8042.nomux [HW] Don't check presence of an active multiplexing
controller
i8042.nopnp [HW] Don't use ACPIPnP / PnPBIOS to discover KBD/AUX
ide= [HW] (E)IDE subsystem
Format: ide=nodma or ide=doubler or ide=reverse
- See Documentation/ide.txt.
+ See Documentation/ide/ide.txt.
ide?= [HW] (E)IDE subsystem
Format: ide?=noprobe or chipset specific parameters.
- See Documentation/ide.txt.
+ See Documentation/ide/ide.txt.
idebus= [HW] (E)IDE subsystem - VLB/PCI bus speed
- See Documentation/ide.txt.
+ See Documentation/ide/ide.txt.
idle= [X86]
Format: idle=poll or idle=mwait
when set.
Format: <int>
+ libata.force= [LIBATA] Force configurations. The format is comma
+ separated list of "[ID:]VAL" where ID is
+ PORT[:DEVICE]. PORT and DEVICE are decimal numbers
+ matching port, link or device. Basically, it matches
+ the ATA ID string printed on console by libata. If
+ the whole ID part is omitted, the last PORT and DEVICE
+ values are used. If ID hasn't been specified yet, the
+ configuration applies to all ports, links and devices.
+
+ If only DEVICE is omitted, the parameter applies to
+ the port and all links and devices behind it. DEVICE
+ number of 0 either selects the first device or the
+ first fan-out link behind PMP device. It does not
+ select the host link. DEVICE number of 15 selects the
+ host link and device attached to it.
+
+ The VAL specifies the configuration to force. As long
+ as there's no ambiguity shortcut notation is allowed.
+ For example, both 1.5 and 1.5G would work for 1.5Gbps.
+ The following configurations can be forced.
+
+ * Cable type: 40c, 80c, short40c, unk, ign or sata.
+ Any ID with matching PORT is used.
+
+ * SATA link speed limit: 1.5Gbps or 3.0Gbps.
+
+ * Transfer mode: pio[0-7], mwdma[0-4] and udma[0-7].
+ udma[/][16,25,33,44,66,100,133] notation is also
+ allowed.
+
+ * [no]ncq: Turn on or off NCQ.
+
+ If there are multiple matching configurations changing
+ the same attribute, the last one is used.
+
load_ramdisk= [RAM] List of ramdisks to load from floppy
See Documentation/ramdisk.txt.
[SCSI] Maximum number of LUNs received.
Should be between 1 and 16384.
- mca-pentium [BUGS=X86-32]
-
mcatest= [IA-64]
mce [X86-32] Machine Check Exception
<deci-seconds>: poll all this frequency
0: no polling (default)
- time Show timing data prefixed to each printk message line
- [deprecated, see 'printk.time']
-
tipar.timeout= [HW,PPT]
Set communications timeout in tenths of a second
(default 15).
git.samba.org / sfrench / cifs-2.6.git / blobdiff