EFI EFI Partitioning (GPT) is enabled
EIDE EIDE/ATAPI support is enabled.
FB The frame buffer device is enabled.
+ GCOV GCOV profiling is enabled.
HW Appropriate hardware is enabled.
IA-64 IA-64 architecture is enabled.
IMA Integrity measurement architecture is enabled.
ISAPNP ISA PnP code is enabled.
ISDN Appropriate ISDN support is enabled.
JOY Appropriate joystick support is enabled.
- KMEMTRACE kmemtrace is enabled.
LIBATA Libata driver is enabled
LP Printer support is enabled.
LOOP Loopback device support is enabled.
to assume that this machine's pmtimer latches its value
and always returns good values.
- acpi.power_nocheck= [HW,ACPI]
- Format: 1/0 enable/disable the check of power state.
- On some bogus BIOS the _PSC object/_STA object of
- power resource can't return the correct device power
- state. In such case it is unneccessary to check its
- power state again in power transition.
- 1 : disable the power state check
-
acpi_sci= [HW,ACPI] ACPI System Control Interrupt trigger mode
Format: { level | edge | high | low }
flushed before they will be reused, which
is a lot of faster
- amd_iommu_size= [HW,X86-64]
- Define the size of the aperture for the AMD IOMMU
- driver. Possible values are:
- '32M', '64M' (default), '128M', '256M', '512M', '1G'
-
amijoy.map= [HW,JOY] Amiga joystick support
Map of devices attached to JOY0DAT and JOY1DAT
Format: <a>,<b>
Also note the kernel might malfunction if you disable
some critical bits.
+ cmo_free_hint= [PPC] Format: { yes | no }
+ Specify whether pages are marked as being inactive
+ when they are freed. This is used in CMO environments
+ to determine OS memory pressure for page stealing by
+ a hypervisor.
+ Default: yes
+
code_bytes [X86] How many bytes of object code to print
in an oops report.
Range: 0 - 8192
console=brl,ttyS0
For now, only VisioBraille is supported.
+ consoleblank= [KNL] The console blank (screen saver) timeout in
+ seconds. Defaults to 10*60 = 10mins. A value of 0
+ disables the blank timer.
+
coredump_filter=
[KNL] Change the default value for
/proc/<pid>/coredump_filter.
DMA-API debugging code disables itself because the
architectural default is too low.
+ dma_debug_driver=<driver_name>
+ With this option the DMA-API debugging driver
+ filter feature can be enabled at boot time. Just
+ pass the driver to filter for as the parameter.
+ The filter can be disabled or changed to another
+ driver later using sysfs.
+
dscc4.setup= [NET]
dtc3181e= [HW,SCSI]
ia64_pal_cache_flush instead of SAL_CACHE_FLUSH.
ftrace=[tracer]
- [ftrace] will set and start the specified tracer
+ [FTRACE] will set and start the specified tracer
as early as possible in order to facilitate early
boot debugging.
ftrace_dump_on_oops
- [ftrace] will dump the trace buffers on oops.
+ [FTRACE] will dump the trace buffers on oops.
+
+ ftrace_filter=[function-list]
+ [FTRACE] Limit the functions traced by the function
+ tracer at boot up. function-list is a comma separated
+ list of functions. This list can be changed at run
+ time by the set_ftrace_filter file in the debugfs
+ tracing directory.
+
+ ftrace_notrace=[function-list]
+ [FTRACE] Do not trace the functions specified in
+ function-list. This list can be changed at run time
+ by the set_ftrace_notrace file in the debugfs
+ tracing directory.
gamecon.map[2|3]=
[HW,JOY] Multisystem joystick and NES/SNES/PSX pad
Format: off | on
default: on
+ gcov_persist= [GCOV] When non-zero (default), profiling data for
+ kernel modules is saved and remains accessible via
+ debugfs, even when the module is unloaded/reloaded.
+ When zero, profiling data is discarded and associated
+ debugfs files are removed at module unload time.
+
gdth= [HW,SCSI]
See header of drivers/scsi/gdth.c.
ide-core.nodma= [HW] (E)IDE subsystem
Format: =0.0 to prevent dma on hda, =0.1 hdb =1.0 hdc
- .vlb_clock .pci_clock .noflush .noprobe .nowerr .cdrom
- .chs .ignore_cable are additional options
- See Documentation/ide/ide.txt.
-
- idebus= [HW] (E)IDE subsystem - VLB/PCI bus speed
+ .vlb_clock .pci_clock .noflush .nohpa .noprobe .nowerr
+ .cdrom .chs .ignore_cable are additional options
See Documentation/ide/ide.txt.
ide-pci-generic.all-generic-ide [HW] (E)IDE subsystem
Formt: { "sha1" | "md5" }
default: "sha1"
+ ima_tcb [IMA]
+ Load a policy which meets the needs of the Trusted
+ Computing Base. This means IMA will measure all
+ programs exec'd, files mmap'd for exec, and all files
+ opened for read by uid=0.
+
in2000= [HW,SCSI]
See header of drivers/scsi/in2000.c.
nomerge
forcesac
soft
+ pt [x86, IA64]
io7= [HW] IO7 for Marvel based alpha systems
See comment before marvel_specify_io7 in
use the HighMem zone if it exists, and the Normal
zone if it does not.
- kmemtrace.enable= [KNL,KMEMTRACE] Format: { yes | no }
- Controls whether kmemtrace is enabled
- at boot-time.
-
- kmemtrace.subbufs=n [KNL,KMEMTRACE] Overrides the number of
- subbufs kmemtrace's relay channel has. Set this
- higher than default (KMEMTRACE_N_SUBBUFS in code) if
- you experience buffer overruns.
-
kgdboc= [HW] kgdb over consoles.
Requires a tty driver that supports console polling.
- (only serial suported for now)
+ (only serial supported for now)
Format: <serial_device>[,baud]
kmac= [MIPS] korina ethernet MAC address.
Configure the RouterBoard 532 series on-chip
Ethernet adapter MAC address.
+ kmemleak= [KNL] Boot-time kmemleak enable/disable
+ Valid arguments: on, off
+ Default: on
+
kstack=N [X86] Print N words from the kernel stack
in oops dumps.
min_addr=nn[KMG] [KNL,BOOT,ia64] All physical memory below this
physical address is ignored.
+ mini2440= [ARM,HW,KNL]
+ Format:[0..2][b][c][t]
+ Default: "0tb"
+ MINI2440 configuration specification:
+ 0 - The attached screen is the 3.5" TFT
+ 1 - The attached screen is the 7" TFT
+ 2 - The VGA Shield is attached (1024x768)
+ Leaving out the screen size parameter will not load
+ the TFT driver, and the framebuffer will be left
+ unconfigured.
+ b - Enable backlight. The TFT backlight pin will be
+ linked to the kernel VESA blanking code and a GPIO
+ LED. This parameter is not necessary when using the
+ VGA shield.
+ c - Enable the s3c camera interface.
+ t - Reserved for enabling touchscreen support. The
+ touchscreen support is not enabled in the mainstream
+ kernel as of 2.6.30, a preliminary port can be found
+ in the "bleeding edge" mini2440 support kernel at
+ http://repo.or.cz/w/linux-2.6/mini2440.git
+
mminit_loglevel=
[KNL] When CONFIG_DEBUG_MEMORY_INIT is set, this
parameter allows control of the logging verbosity for
mtdparts= [MTD]
See drivers/mtd/cmdlinepart.c.
+ onenand.bdry= [HW,MTD] Flex-OneNAND Boundary Configuration
+
+ Format: [die0_boundary][,die0_lock][,die1_boundary][,die1_lock]
+
+ boundary - index of last SLC block on Flex-OneNAND.
+ The remaining blocks are configured as MLC blocks.
+ lock - Configure if Flex-OneNAND boundary should be locked.
+ Once locked, the boundary cannot be changed.
+ 1 indicates lock status, 0 indicates unlock status.
+
mtdset= [ARM]
ARM/S3C2412 JIVE boot control
('y', default) or cooked coordinates ('n')
mtrr_chunk_size=nn[KMG] [X86]
- used for mtrr cleanup. It is largest continous chunk
+ used for mtrr cleanup. It is largest continuous chunk
that could hold holes aka. UC entries.
mtrr_gran_size=nn[KMG] [X86]
noinitrd [RAM] Tells the kernel not to load any configured
initial RAM disk.
+ nointremap [X86-64, Intel-IOMMU] Do not enable interrupt
+ remapping.
+
nointroute [IA-64]
nojitter [IA64] Disables jitter checking for ITC timers.
oprofile.timer= [HW]
Use timer interrupt instead of performance counters
+ oprofile.cpu_type= Force an oprofile cpu type
+ This might be useful if you have an older oprofile
+ userland or if you want common events.
+ Format: { archperfmon }
+ archperfmon: [X86] Force use of architectural
+ perfmon on Intel CPUs instead of the
+ CPU specific event set.
+
osst= [HW,SCSI] SCSI Tape Driver
Format: <buffer_size>,<write_threshold>
See also Documentation/scsi/st.txt.
root domains (aka PCI segments, in ACPI-speak).
nommconf [X86] Disable use of MMCONFIG for PCI
Configuration
+ check_enable_amd_mmconf [X86] check for and enable
+ properly configured MMIO access to PCI
+ config space on AMD family 10h CPU
nomsi [MSI] If the PCI_MSI kernel config parameter is
enabled, this kernel boot option can be used to
disable the use of MSI interrupts system-wide.
IRQ routing is enabled.
noacpi [X86] Do not use ACPI for IRQ routing
or for PCI scanning.
- use_crs [X86] Use _CRS for PCI resource
+ nocrs [X86] Don't use _CRS for PCI resource
allocation.
routeirq Do IRQ routing for all PCI devices.
This is normally done in pci_enable_device(),
PAGE_SIZE is used as alignment.
PCI-PCI bridge can be specified, if resource
windows need to be expanded.
+ ecrc= Enable/disable PCIe ECRC (transaction layer
+ end-to-end CRC checking).
+ bios: Use BIOS/firmware settings. This is the
+ the default.
+ off: Turn ECRC off
+ on: Turn ECRC on.
pcie_aspm= [PCIE] Forcibly enable or disable PCIe Active State Power
Management.
git.samba.org / sfrench / cifs-2.6.git / blobdiff