regshifts=<shift1>,<shift2>,...
slave_addrs=<addr1>,<addr2>,...
force_kipmid=<enable1>,<enable2>,...
+ unload_when_empty=[0|1]
Each of these except si_trydefaults is a list, the first item for the
first interface, second item for the second interface, etc.
or users that don't want the daemon (don't need the performance, don't
want the CPU hit) can disable it.
+If unload_when_empty is set to 1, the driver will be unloaded if it
+doesn't find any interfaces or all the interfaces fail to work. The
+default is one. Setting to 0 is useful with the hotmod, but is
+obviously only useful for modules.
+
When compiled into the kernel, the parameters can be specified on the
kernel command line as:
0xca2. If you want to turn this off, set the "trydefaults" option to
false.
-If you have high-res timers compiled into the kernel, the driver will
-use them to provide much better performance. Note that if you do not
-have high-res timers enabled in the kernel and you don't have
-interrupts enabled, the driver will run VERY slowly. Don't blame me,
+If your IPMI interface does not support interrupts and is a KCS or
+SMIC interface, the IPMI driver will start a kernel thread for the
+interface to help speed things up. This is a low-priority kernel
+thread that constantly polls the IPMI driver while an IPMI operation
+is in progress. The force_kipmid module parameter will all the user to
+force this thread on or off. If you force it off and don't have
+interrupts, the driver will run VERY slowly. Don't blame me,
these interfaces suck.
+The driver supports a hot add and remove of interfaces. This way,
+interfaces can be added or removed after the kernel is up and running.
+This is done using /sys/modules/ipmi_si/parameters/hotmod, which is a
+write-only parameter. You write a string to this interface. The string
+has the format:
+ <op1>[:op2[:op3...]]
+The "op"s are:
+ add|remove,kcs|bt|smic,mem|i/o,<address>[,<opt1>[,<opt2>[,...]]]
+You can specify more than one interface on the line. The "opt"s are:
+ rsp=<regspacing>
+ rsi=<regsize>
+ rsh=<regshift>
+ irq=<irq>
+ ipmb=<ipmb slave addr>
+and these have the same meanings as discussed above. Note that you
+can also use this on the kernel command line for a more compact format
+for specifying an interface. Note that when removing an interface,
+only the first three parameters (si type, address type, and address)
+are used for the comparison. Any options are ignored for removing.
The SMBus Driver
----------------
modprobe ipmi_watchdog timeout=<t> pretimeout=<t> action=<action type>
preaction=<preaction type> preop=<preop type> start_now=x
- nowayout=x
+ nowayout=x ifnum_to_use=n
+
+ifnum_to_use specifies which interface the watchdog timer should use.
+The default is -1, which means to pick the first one registered.
The timeout is the number of seconds to the action, and the pretimeout
is the amount of seconds before the reset that the pre-timeout panic will
gets a pre-action. During a panic or a reboot, the watchdog will
start a 120 timer if it is running to make sure the reboot occurs.
-Note that if you use the NMI preaction for the watchdog, you MUST
-NOT use nmi watchdog mode 1. If you use the NMI watchdog, you
-must use mode 2.
+Note that if you use the NMI preaction for the watchdog, you MUST NOT
+use the nmi watchdog. There is no reasonable way to tell if an NMI
+comes from the IPMI controller, so it must assume that if it gets an
+otherwise unhandled NMI, it must be from IPMI and it will panic
+immediately.
Once you open the watchdog timer, you must write a 'V' character to the
device to close it, or the timer will not stop. This is a new semantic
in /proc/sys/dev/ipmi/poweroff_powercycle. Note that if the system
does not support power cycling, it will always do the power off.
+The "ifnum_to_use" parameter specifies which interface the poweroff
+code should use. The default is -1, which means to pick the first one
+registered.
+
Note that if you have ACPI enabled, the system will prefer using ACPI to
power off.
git.samba.org / sfrench / cifs-2.6.git / blobdiff