# # Wireless LAN device configuration # menu "Wireless LAN" depends on !S390 config WLAN_PRE80211 bool "Wireless LAN (pre-802.11)" depends on NETDEVICES ---help--- Say Y if you have any pre-802.11 wireless LAN hardware. This option does not affect the kernel build, it only lets you choose drivers. config STRIP tristate "STRIP (Metricom starmode radio IP)" depends on INET && WLAN_PRE80211 select WIRELESS_EXT ---help--- Say Y if you have a Metricom radio and intend to use Starmode Radio IP. STRIP is a radio protocol developed for the MosquitoNet project (on the WWW at ) to send Internet traffic using Metricom radios. Metricom radios are small, battery powered, 100kbit/sec packet radio transceivers, about the size and weight of a cellular telephone. (You may also have heard them called "Metricom modems" but we avoid the term "modem" because it misleads many people into thinking that you can plug a Metricom modem into a phone line and use it as a modem.) You can use STRIP on any Linux machine with a serial port, although it is obviously most useful for people with laptop computers. If you think you might get a Metricom radio in the future, there is no harm in saying Y to STRIP now, except that it makes the kernel a bit bigger. To compile this as a module, choose M here: the module will be called strip. config ARLAN tristate "Aironet Arlan 655 & IC2200 DS support" depends on ISA && !64BIT && WLAN_PRE80211 select WIRELESS_EXT ---help--- Aironet makes Arlan, a class of wireless LAN adapters. These use the www.Telxon.com chip, which is also used on several similar cards. This driver is tested on the 655 and IC2200 series cards. Look at for the latest information. The driver is built as two modules, arlan and arlan-proc. The latter is the /proc interface and is not needed most of time. On some computers the card ends up in non-valid state after some time. Use a ping-reset script to clear it. config WAVELAN tristate "AT&T/Lucent old WaveLAN & DEC RoamAbout DS ISA support" depends on ISA && WLAN_PRE80211 select WIRELESS_EXT ---help--- The Lucent WaveLAN (formerly NCR and AT&T; or DEC RoamAbout DS) is a Radio LAN (wireless Ethernet-like Local Area Network) using the radio frequencies 900 MHz and 2.4 GHz. If you want to use an ISA WaveLAN card under Linux, say Y and read the Ethernet-HOWTO, available from . Some more specific information is contained in and in the source code . You will also need the wireless tools package available from . Please read the man pages contained therein. To compile this driver as a module, choose M here: the module will be called wavelan. config PCMCIA_WAVELAN tristate "AT&T/Lucent old WaveLAN Pcmcia wireless support" depends on PCMCIA && WLAN_PRE80211 select WIRELESS_EXT help Say Y here if you intend to attach an AT&T/Lucent Wavelan PCMCIA (PC-card) wireless Ethernet networking card to your computer. This driver is for the non-IEEE-802.11 Wavelan cards. To compile this driver as a module, choose M here: the module will be called wavelan_cs. If unsure, say N. config PCMCIA_NETWAVE tristate "Xircom Netwave AirSurfer Pcmcia wireless support" depends on PCMCIA && WLAN_PRE80211 select WIRELESS_EXT help Say Y here if you intend to attach this type of PCMCIA (PC-card) wireless Ethernet networking card to your computer. To compile this driver as a module, choose M here: the module will be called netwave_cs. If unsure, say N. config WLAN_80211 bool "Wireless LAN (IEEE 802.11)" depends on NETDEVICES ---help--- Say Y if you have any 802.11 wireless LAN hardware. This option does not affect the kernel build, it only lets you choose drivers. config PCMCIA_RAYCS tristate "Aviator/Raytheon 2.4GHz wireless support" depends on PCMCIA && WLAN_80211 select WIRELESS_EXT ---help--- Say Y here if you intend to attach an Aviator/Raytheon PCMCIA (PC-card) wireless Ethernet networking card to your computer. Please read the file for details. To compile this driver as a module, choose M here: the module will be called ray_cs. If unsure, say N. config LIBERTAS tristate "Marvell 8xxx Libertas WLAN driver support" depends on WLAN_80211 select WIRELESS_EXT select LIB80211 select FW_LOADER ---help--- A library for Marvell Libertas 8xxx devices. config LIBERTAS_USB tristate "Marvell Libertas 8388 USB 802.11b/g cards" depends on LIBERTAS && USB ---help--- A driver for Marvell Libertas 8388 USB devices. config LIBERTAS_CS tristate "Marvell Libertas 8385 CompactFlash 802.11b/g cards" depends on LIBERTAS && PCMCIA select FW_LOADER ---help--- A driver for Marvell Libertas 8385 CompactFlash devices. config LIBERTAS_SDIO tristate "Marvell Libertas 8385 and 8686 SDIO 802.11b/g cards" depends on LIBERTAS && MMC ---help--- A driver for Marvell Libertas 8385 and 8686 SDIO devices. config LIBERTAS_SPI tristate "Marvell Libertas 8686 SPI 802.11b/g cards" depends on LIBERTAS && SPI && GENERIC_GPIO ---help--- A driver for Marvell Libertas 8686 SPI devices. config LIBERTAS_DEBUG bool "Enable full debugging output in the Libertas module." depends on LIBERTAS ---help--- Debugging support. config LIBERTAS_THINFIRM tristate "Marvell 8xxx Libertas WLAN driver support with thin firmware" depends on WLAN_80211 && MAC80211 select FW_LOADER ---help--- A library for Marvell Libertas 8xxx devices using thinfirm. config LIBERTAS_THINFIRM_USB tristate "Marvell Libertas 8388 USB 802.11b/g cards with thin firmware" depends on LIBERTAS_THINFIRM && USB ---help--- A driver for Marvell Libertas 8388 USB devices using thinfirm. config AIRO tristate "Cisco/Aironet 34X/35X/4500/4800 ISA and PCI cards" depends on ISA_DMA_API && WLAN_80211 && (PCI || BROKEN) select WIRELESS_EXT select CRYPTO ---help--- This is the standard Linux driver to support Cisco/Aironet ISA and PCI 802.11 wireless cards. It supports the new 802.11b cards from Cisco (Cisco 34X, Cisco 35X - with or without encryption) as well as card before the Cisco acquisition (Aironet 4500, Aironet 4800, Aironet 4800B). This driver support both the standard Linux Wireless Extensions and Cisco proprietary API, so both the Linux Wireless Tools and the Cisco Linux utilities can be used to configure the card. The driver can be compiled as a module and will be named "airo". config ATMEL tristate "Atmel at76c50x chipset 802.11b support" depends on (PCI || PCMCIA) && WLAN_80211 select WIRELESS_EXT select FW_LOADER select CRC32 ---help--- A driver 802.11b wireless cards based on the Atmel fast-vnet chips. This driver supports standard Linux wireless extensions. Many cards based on this chipset do not have flash memory and need their firmware loaded at start-up. If yours is one of these, you will need to provide a firmware image to be loaded into the card by the driver. The Atmel firmware package can be downloaded from config PCI_ATMEL tristate "Atmel at76c506 PCI cards" depends on ATMEL && PCI ---help--- Enable support for PCI and mini-PCI cards containing the Atmel at76c506 chip. config PCMCIA_ATMEL tristate "Atmel at76c502/at76c504 PCMCIA cards" depends on ATMEL && PCMCIA select WIRELESS_EXT select FW_LOADER select CRC32 ---help--- Enable support for PCMCIA cards containing the Atmel at76c502 and at76c504 chips. config AT76C50X_USB tristate "Atmel at76c503/at76c505/at76c505a USB cards" depends on MAC80211 && WLAN_80211 && USB select FW_LOADER ---help--- Enable support for USB Wireless devices using Atmel at76c503, at76c505 or at76c505a chips. config AIRO_CS tristate "Cisco/Aironet 34X/35X/4500/4800 PCMCIA cards" depends on PCMCIA && (BROKEN || !M32R) && WLAN_80211 select WIRELESS_EXT select CRYPTO select CRYPTO_AES ---help--- This is the standard Linux driver to support Cisco/Aironet PCMCIA 802.11 wireless cards. This driver is the same as the Aironet driver part of the Linux Pcmcia package. It supports the new 802.11b cards from Cisco (Cisco 34X, Cisco 35X - with or without encryption) as well as card before the Cisco acquisition (Aironet 4500, Aironet 4800, Aironet 4800B). It also supports OEM of Cisco such as the DELL TrueMobile 4800 and Xircom 802.11b cards. This driver support both the standard Linux Wireless Extensions and Cisco proprietary API, so both the Linux Wireless Tools and the Cisco Linux utilities can be used to configure the card. config PCMCIA_WL3501 tristate "Planet WL3501 PCMCIA cards" depends on EXPERIMENTAL && PCMCIA && WLAN_80211 select WIRELESS_EXT ---help--- A driver for WL3501 PCMCIA 802.11 wireless cards made by Planet. It has basic support for Linux wireless extensions and initial micro support for ethtool. config PRISM54 tristate 'Intersil Prism GT/Duette/Indigo PCI/Cardbus' depends on PCI && EXPERIMENTAL && WLAN_80211 select WIRELESS_EXT select FW_LOADER ---help--- Enable PCI and Cardbus support for the following chipset based cards: ISL3880 - Prism GT 802.11 b/g ISL3877 - Prism Indigo 802.11 a ISL3890 - Prism Duette 802.11 a/b/g For a complete list of supported cards visit . Here is the latest confirmed list of supported cards: 3com OfficeConnect 11g Cardbus Card aka 3CRWE154G72 (version 1) Allnet ALL0271 PCI Card Compex WL54G Cardbus Card Corega CG-WLCB54GT Cardbus Card D-Link Air Plus Xtreme G A1 Cardbus Card aka DWL-g650 I-O Data WN-G54/CB Cardbus Card Kobishi XG-300 aka Z-Com Cardbus Card Netgear WG511 Cardbus Card Ovislink WL-5400PCI PCI Card Peabird WLG-PCI PCI Card Sitecom WL-100i Cardbus Card Sitecom WL-110i PCI Card SMC2802W - EZ Connect g 2.4GHz 54 Mbps Wireless PCI Card SMC2835W - EZ Connect g 2.4GHz 54 Mbps Wireless Cardbus Card SMC2835W-V2 - EZ Connect g 2.4GHz 54 Mbps Wireless Cardbus Card Z-Com XG-900 PCI Card Zyxel G-100 Cardbus Card If you enable this you will need a firmware file as well. You will need to copy this to /usr/lib/hotplug/firmware/isl3890. You can get this non-GPL'd firmware file from the Prism54 project page: You will also need the /etc/hotplug/firmware.agent script from a current hotplug package. Note: You need a motherboard with DMA support to use any of these cards If you want to compile the driver as a module ( = code which can be inserted in and removed from the running kernel whenever you want), say M here and read . The module will be called prism54.ko. config USB_ZD1201 tristate "USB ZD1201 based Wireless device support" depends on USB && WLAN_80211 select WIRELESS_EXT select FW_LOADER ---help--- Say Y if you want to use wireless LAN adapters based on the ZyDAS ZD1201 chip. This driver makes the adapter appear as a normal Ethernet interface, typically on wlan0. The zd1201 device requires external firmware to be loaded. This can be found at http://linux-lc100020.sourceforge.net/ To compile this driver as a module, choose M here: the module will be called zd1201. config USB_NET_RNDIS_WLAN tristate "Wireless RNDIS USB support" depends on USB && WLAN_80211 && EXPERIMENTAL select USB_USBNET select USB_NET_CDCETHER select USB_NET_RNDIS_HOST select WIRELESS_EXT ---help--- This is a driver for wireless RNDIS devices. These are USB based adapters found in devices such as: Buffalo WLI-U2-KG125S U.S. Robotics USR5421 Belkin F5D7051 Linksys WUSB54GSv2 Linksys WUSB54GSC Asus WL169gE Eminent EM4045 BT Voyager 1055 Linksys WUSB54GSv1 U.S. Robotics USR5420 BUFFALO WLI-USB-G54 All of these devices are based on Broadcom 4320 chip which is the only wireless RNDIS chip known to date. If you choose to build a module, it'll be called rndis_wlan. config RTL8180 tristate "Realtek 8180/8185 PCI support" depends on MAC80211 && PCI && WLAN_80211 && EXPERIMENTAL select EEPROM_93CX6 ---help--- This is a driver for RTL8180 and RTL8185 based cards. These are PCI based chips found in cards such as: (RTL8185 802.11g) A-Link WL54PC (RTL8180 802.11b) Belkin F5D6020 v3 Belkin F5D6020 v3 Dlink DWL-610 Dlink DWL-510 Netgear MA521 Level-One WPC-0101 Acer Aspire 1357 LMi VCTnet PC-11B1 Ovislink AirLive WL-1120PCM Mentor WL-PCI Linksys WPC11 v4 TrendNET TEW-288PI D-Link DWL-520 Rev D Repotec RP-WP7126 TP-Link TL-WN250/251 Zonet ZEW1000 Longshine LCS-8031-R HomeLine HLW-PCC200 GigaFast WF721-AEX Planet WL-3553 Encore ENLWI-PCI1-NT TrendNET TEW-266PC Gigabyte GN-WLMR101 Siemens-fujitsu Amilo D1840W Edimax EW-7126 PheeNet WL-11PCIR Tonze PC-2100T Planet WL-8303 Dlink DWL-650 v M1 Edimax EW-7106 Q-Tec 770WC Topcom Skyr@cer 4011b Roper FreeLan 802.11b (edition 2004) Wistron Neweb Corp CB-200B Pentagram HorNET QTec 775WC TwinMOS Booming B Series Micronet SP906BB Sweex LC700010 Surecom EP-9428 Safecom SWLCR-1100 Thanks to Realtek for their support! config RTL8187 tristate "Realtek 8187 and 8187B USB support" depends on MAC80211 && USB && WLAN_80211 select EEPROM_93CX6 ---help--- This is a driver for RTL8187 and RTL8187B based cards. These are USB based chips found in devices such as: Netgear WG111v2 Level 1 WNC-0301USB Micronet SP907GK V5 Encore ENUWI-G2 Trendnet TEW-424UB ASUS P5B Deluxe Toshiba Satellite Pro series of laptops Asus Wireless Link Thanks to Realtek for their support! config ADM8211 tristate "ADMtek ADM8211 support" depends on MAC80211 && PCI && WLAN_80211 && EXPERIMENTAL select CRC32 select EEPROM_93CX6 ---help--- This driver is for ADM8211A, ADM8211B, and ADM8211C based cards. These are PCI/mini-PCI/Cardbus 802.11b chips found in cards such as: Xterasys Cardbus XN-2411b Blitz NetWave Point PC TrendNet 221pc Belkin F5D6001 SMC 2635W Linksys WPC11 v1 Fiberline FL-WL-200X 3com Office Connect (3CRSHPW796) Corega WLPCIB-11 SMC 2602W V2 EU D-Link DWL-520 Revision C However, some of these cards have been replaced with other chips like the RTL8180L (Xterasys Cardbus XN-2411b, Belkin F5D6001) or the Ralink RT2400 (SMC2635W) without a model number change. Thanks to Infineon-ADMtek for their support of this driver. config MAC80211_HWSIM tristate "Simulated radio testing tool for mac80211" depends on MAC80211 && WLAN_80211 ---help--- This driver is a developer testing tool that can be used to test IEEE 802.11 networking stack (mac80211) functionality. This is not needed for normal wireless LAN usage and is only for testing. See Documentation/networking/mac80211_hwsim for more information on how to use this tool. To compile this driver as a module, choose M here: the module will be called mac80211_hwsim. If unsure, say N. config MWL8K tristate "Marvell 88W8xxx PCI/PCIe Wireless support" depends on MAC80211 && PCI && WLAN_80211 && EXPERIMENTAL ---help--- This driver supports Marvell TOPDOG 802.11 wireless cards. To compile this driver as a module, choose M here: the module will be called mwl8k. If unsure, say N. source "drivers/net/wireless/p54/Kconfig" source "drivers/net/wireless/ath5k/Kconfig" source "drivers/net/wireless/ath9k/Kconfig" source "drivers/net/wireless/ar9170/Kconfig" source "drivers/net/wireless/ipw2x00/Kconfig" source "drivers/net/wireless/iwlwifi/Kconfig" source "drivers/net/wireless/hostap/Kconfig" source "drivers/net/wireless/b43/Kconfig" source "drivers/net/wireless/b43legacy/Kconfig" source "drivers/net/wireless/zd1211rw/Kconfig" source "drivers/net/wireless/rt2x00/Kconfig" source "drivers/net/wireless/orinoco/Kconfig" endmenu