# # Input core configuration # menuconfig INPUT_KEYBOARD bool "Keyboards" if EMBEDDED || !X86 default y help Say Y here, and a list of supported keyboards will be displayed. This option doesn't affect the kernel. If unsure, say Y. if INPUT_KEYBOARD config KEYBOARD_AAED2000 tristate "AAED-2000 keyboard" depends on MACH_AAED2000 select INPUT_POLLDEV default y help Say Y here to enable the keyboard on the Agilent AAED-2000 development board. To compile this driver as a module, choose M here: the module will be called aaed2000_kbd. config KEYBOARD_ADP5520 tristate "Keypad Support for ADP5520 PMIC" depends on PMIC_ADP5520 help This option enables support for the keypad scan matrix on Analog Devices ADP5520 PMICs. To compile this driver as a module, choose M here: the module will be called adp5520-keys. config KEYBOARD_ADP5588 tristate "ADP5588/87 I2C QWERTY Keypad and IO Expander" depends on I2C help Say Y here if you want to use a ADP5588/87 attached to your system I2C bus. To compile this driver as a module, choose M here: the module will be called adp5588-keys. config KEYBOARD_AMIGA tristate "Amiga keyboard" depends on AMIGA help Say Y here if you are running Linux on any AMIGA and have a keyboard attached. To compile this driver as a module, choose M here: the module will be called amikbd. config ATARI_KBD_CORE bool config KEYBOARD_ATARI tristate "Atari keyboard" depends on ATARI select ATARI_KBD_CORE help Say Y here if you are running Linux on any Atari and have a keyboard attached. To compile this driver as a module, choose M here: the module will be called atakbd. config KEYBOARD_ATKBD tristate "AT keyboard" if EMBEDDED || !X86 default y select SERIO select SERIO_LIBPS2 select SERIO_I8042 if X86 && !X86_MRST select SERIO_GSCPS2 if GSC help Say Y here if you want to use a standard AT or PS/2 keyboard. Usually you'll need this, unless you have a different type keyboard (USB, ADB or other). This also works for AT and PS/2 keyboards connected over a PS/2 to serial converter. If unsure, say Y. To compile this driver as a module, choose M here: the module will be called atkbd. config KEYBOARD_ATKBD_HP_KEYCODES bool "Use HP keyboard scancodes" depends on PARISC && KEYBOARD_ATKBD default y help Say Y here if you have a PA-RISC machine and want to use an AT or PS/2 keyboard, and your keyboard uses keycodes that are specific to PA-RISC keyboards. Say N if you use a standard keyboard. config KEYBOARD_ATKBD_RDI_KEYCODES bool "Use PrecisionBook keyboard scancodes" depends on KEYBOARD_ATKBD_HP_KEYCODES default n help If you have an RDI PrecisionBook, say Y here if you want to use its built-in keyboard (as opposed to an external keyboard). The PrecisionBook has five keys that conflict with those used by most AT and PS/2 keyboards. These are as follows: PrecisionBook Standard AT or PS/2 F1 F12 Left Ctrl Left Alt Caps Lock Left Ctrl Right Ctrl Caps Lock Left 102nd key (the key to the right of Left Shift) If you say N here, and use the PrecisionBook keyboard, then each key in the left-hand column will be interpreted as the corresponding key in the right-hand column. If you say Y here, and use an external keyboard, then each key in the right-hand column will be interpreted as the key shown in the left-hand column. config QT2160 tristate "Atmel AT42QT2160 Touch Sensor Chip" depends on I2C && EXPERIMENTAL help If you say yes here you get support for Atmel AT42QT2160 Touch Sensor chip as a keyboard input. This driver can also be built as a module. If so, the module will be called qt2160. config KEYBOARD_BFIN tristate "Blackfin BF54x keypad support" depends on (BF54x && !BF544) help Say Y here if you want to use the BF54x keypad. To compile this driver as a module, choose M here: the module will be called bf54x-keys. config KEYBOARD_LKKBD tristate "DECstation/VAXstation LK201/LK401 keyboard" select SERIO help Say Y here if you want to use a LK201 or LK401 style serial keyboard. This keyboard is also useable on PCs if you attach it with the inputattach program. The connector pinout is described within lkkbd.c. To compile this driver as a module, choose M here: the module will be called lkkbd. config KEYBOARD_EP93XX tristate "EP93xx Matrix Keypad support" depends on ARCH_EP93XX help Say Y here to enable the matrix keypad on the Cirrus EP93XX. To compile this driver as a module, choose M here: the module will be called ep93xx_keypad. config KEYBOARD_GPIO tristate "GPIO Buttons" depends on GENERIC_GPIO help This driver implements support for buttons connected to GPIO pins of various CPUs (and some other chips). Say Y here if your device has buttons connected directly to such GPIO pins. Your board-specific setup logic must also provide a platform device, with configuration data saying which GPIOs are used. To compile this driver as a module, choose M here: the module will be called gpio_keys. config KEYBOARD_TCA6416 tristate "TCA6416 Keypad Support" depends on I2C help This driver implements basic keypad functionality for keys connected through TCA6416 IO expander Say Y here if your device has keys connected to TCA6416 IO expander. Your board-specific setup logic must also provide pin-mask details(of which TCA6416 pins are used for keypad). If enabled the complete TCA6416 device will be managed through this driver. config KEYBOARD_MATRIX tristate "GPIO driven matrix keypad support" depends on GENERIC_GPIO help Enable support for GPIO driven matrix keypad. To compile this driver as a module, choose M here: the module will be called matrix_keypad. config KEYBOARD_HIL_OLD tristate "HP HIL keyboard support (simple driver)" depends on GSC || HP300 default y help The "Human Interface Loop" is a older, 8-channel USB-like controller used in several Hewlett Packard models. This driver was adapted from the one written for m68k/hp300, and implements support for a keyboard attached to the HIL port, but not for any other types of HIL input devices like mice or tablets. However, it has been thoroughly tested and is stable. If you want full HIL support including support for multiple keyboards, mice, and tablets, you have to enable the "HP System Device Controller i8042 Support" in the input/serio submenu. config KEYBOARD_HIL tristate "HP HIL keyboard/pointer support" depends on GSC || HP300 default y select HP_SDC select HIL_MLC select SERIO help The "Human Interface Loop" is a older, 8-channel USB-like controller used in several Hewlett Packard models. This driver implements support for HIL-keyboards and pointing devices (mice, tablets, touchscreens) attached to your machine, so normally you should say Y here. config KEYBOARD_HP6XX tristate "HP Jornada 6xx keyboard" depends on SH_HP6XX select INPUT_POLLDEV help Say Y here if you have a HP Jornada 620/660/680/690 and want to support the built-in keyboard. To compile this driver as a module, choose M here: the module will be called jornada680_kbd. config KEYBOARD_HP7XX tristate "HP Jornada 7xx keyboard" depends on SA1100_JORNADA720_SSP && SA1100_SSP help Say Y here if you have a HP Jornada 710/720/728 and want to support the built-in keyboard. To compile this driver as a module, choose M here: the module will be called jornada720_kbd. config KEYBOARD_LM8323 tristate "LM8323 keypad chip" depends on I2C depends on LEDS_CLASS help If you say yes here you get support for the National Semiconductor LM8323 keypad controller. To compile this driver as a module, choose M here: the module will be called lm8323. config KEYBOARD_LOCOMO tristate "LoCoMo Keyboard Support" depends on SHARP_LOCOMO help Say Y here if you are running Linux on a Sharp Zaurus Collie or Poodle based PDA To compile this driver as a module, choose M here: the module will be called locomokbd. config KEYBOARD_MAPLE tristate "Maple bus keyboard" depends on SH_DREAMCAST && MAPLE help Say Y here if you have a Dreamcast console running Linux and have a keyboard attached to its Maple bus. To compile this driver as a module, choose M here: the module will be called maple_keyb. config KEYBOARD_MAX7359 tristate "Maxim MAX7359 Key Switch Controller" depends on I2C help If you say yes here you get support for the Maxim MAX7359 Key Switch Controller chip. This providers microprocessors with management of up to 64 key switches To compile this driver as a module, choose M here: the module will be called max7359_keypad. config KEYBOARD_IMX tristate "IMX keypad support" depends on ARCH_MXC help Enable support for IMX keypad port. To compile this driver as a module, choose M here: the module will be called imx_keypad. config KEYBOARD_NEWTON tristate "Newton keyboard" select SERIO help Say Y here if you have a Newton keyboard on a serial port. To compile this driver as a module, choose M here: the module will be called newtonkbd. config KEYBOARD_OPENCORES tristate "OpenCores Keyboard Controller" help Say Y here if you want to use the OpenCores Keyboard Controller http://www.opencores.org/project,keyboardcontroller To compile this driver as a module, choose M here; the module will be called opencores-kbd. config KEYBOARD_PXA27x tristate "PXA27x/PXA3xx keypad support" depends on PXA27x || PXA3xx help Enable support for PXA27x/PXA3xx keypad controller. To compile this driver as a module, choose M here: the module will be called pxa27x_keypad. config KEYBOARD_PXA930_ROTARY tristate "PXA930/PXA935 Enhanced Rotary Controller Support" depends on CPU_PXA930 || CPU_PXA935 help Enable support for PXA930/PXA935 Enhanced Rotary Controller. To compile this driver as a module, choose M here: the module will be called pxa930_rotary. config KEYBOARD_STOWAWAY tristate "Stowaway keyboard" select SERIO help Say Y here if you have a Stowaway keyboard on a serial port. Stowaway compatible keyboards like Dicota Input-PDA keyboard are also supported by this driver. To compile this driver as a module, choose M here: the module will be called stowaway. config KEYBOARD_SUNKBD tristate "Sun Type 4 and Type 5 keyboard" select SERIO help Say Y here if you want to use a Sun Type 4 or Type 5 keyboard, connected either to the Sun keyboard connector or to an serial (RS-232) port via a simple adapter. To compile this driver as a module, choose M here: the module will be called sunkbd. config KEYBOARD_SH_KEYSC tristate "SuperH KEYSC keypad support" depends on SUPERH || ARCH_SHMOBILE help Say Y here if you want to use a keypad attached to the KEYSC block on SuperH processors such as sh7722 and sh7343. To compile this driver as a module, choose M here: the module will be called sh_keysc. config KEYBOARD_DAVINCI tristate "TI DaVinci Key Scan" depends on ARCH_DAVINCI_DM365 help Say Y to enable keypad module support for the TI DaVinci platforms (DM365). To compile this driver as a module, choose M here: the module will be called davinci_keyscan. config KEYBOARD_OMAP tristate "TI OMAP keypad support" depends on (ARCH_OMAP1 || ARCH_OMAP2) help Say Y here if you want to use the OMAP keypad. To compile this driver as a module, choose M here: the module will be called omap-keypad. config KEYBOARD_TWL4030 tristate "TI TWL4030/TWL5030/TPS659x0 keypad support" depends on TWL4030_CORE help Say Y here if your board use the keypad controller on TWL4030 family chips. It's safe to say enable this even on boards that don't use the keypad controller. To compile this driver as a module, choose M here: the module will be called twl4030_keypad. config KEYBOARD_XTKBD tristate "XT keyboard" select SERIO help Say Y here if you want to use the old IBM PC/XT keyboard (or compatible) on your system. This is only possible with a parallel port keyboard adapter, you cannot connect it to the keyboard port on a PC that runs Linux. To compile this driver as a module, choose M here: the module will be called xtkbd. config KEYBOARD_W90P910 tristate "W90P910 Matrix Keypad support" depends on ARCH_W90X900 help Say Y here to enable the matrix keypad on evaluation board based on W90P910. To compile this driver as a module, choose M here: the module will be called w90p910_keypad. endif