Written by: Neil Brown Please see MAINTAINERS file for where to send questions. Overlay Filesystem ================== This document describes a prototype for a new approach to providing overlay-filesystem functionality in Linux (sometimes referred to as union-filesystems). An overlay-filesystem tries to present a filesystem which is the result over overlaying one filesystem on top of the other. The result will inevitably fail to look exactly like a normal filesystem for various technical reasons. The expectation is that many use cases will be able to ignore these differences. This approach is 'hybrid' because the objects that appear in the filesystem do not all appear to belong to that filesystem. In many cases an object accessed in the union will be indistinguishable from accessing the corresponding object from the original filesystem. This is most obvious from the 'st_dev' field returned by stat(2). While directories will report an st_dev from the overlay-filesystem, all non-directory objects will report an st_dev from the lower or upper filesystem that is providing the object. Similarly st_ino will only be unique when combined with st_dev, and both of these can change over the lifetime of a non-directory object. Many applications and tools ignore these values and will not be affected. Upper and Lower --------------- An overlay filesystem combines two filesystems - an 'upper' filesystem and a 'lower' filesystem. When a name exists in both filesystems, the object in the 'upper' filesystem is visible while the object in the 'lower' filesystem is either hidden or, in the case of directories, merged with the 'upper' object. It would be more correct to refer to an upper and lower 'directory tree' rather than 'filesystem' as it is quite possible for both directory trees to be in the same filesystem and there is no requirement that the root of a filesystem be given for either upper or lower. The lower filesystem can be any filesystem supported by Linux and does not need to be writable. The lower filesystem can even be another overlayfs. The upper filesystem will normally be writable and if it is it must support the creation of trusted.* extended attributes, and must provide valid d_type in readdir responses, so NFS is not suitable. A read-only overlay of two read-only filesystems may use any filesystem type. Directories ----------- Overlaying mainly involves directories. If a given name appears in both upper and lower filesystems and refers to a non-directory in either, then the lower object is hidden - the name refers only to the upper object. Where both upper and lower objects are directories, a merged directory is formed. At mount time, the two directories given as mount options "lowerdir" and "upperdir" are combined into a merged directory: mount -t overlay overlay -olowerdir=/lower,upperdir=/upper,\ workdir=/work /merged The "workdir" needs to be an empty directory on the same filesystem as upperdir. Then whenever a lookup is requested in such a merged directory, the lookup is performed in each actual directory and the combined result is cached in the dentry belonging to the overlay filesystem. If both actual lookups find directories, both are stored and a merged directory is created, otherwise only one is stored: the upper if it exists, else the lower. Only the lists of names from directories are merged. Other content such as metadata and extended attributes are reported for the upper directory only. These attributes of the lower directory are hidden. whiteouts and opaque directories -------------------------------- In order to support rm and rmdir without changing the lower filesystem, an overlay filesystem needs to record in the upper filesystem that files have been removed. This is done using whiteouts and opaque directories (non-directories are always opaque). A whiteout is created as a character device with 0/0 device number. When a whiteout is found in the upper level of a merged directory, any matching name in the lower level is ignored, and the whiteout itself is also hidden. A directory is made opaque by setting the xattr "trusted.overlay.opaque" to "y". Where the upper filesystem contains an opaque directory, any directory in the lower filesystem with the same name is ignored. readdir ------- When a 'readdir' request is made on a merged directory, the upper and lower directories are each read and the name lists merged in the obvious way (upper is read first, then lower - entries that already exist are not re-added). This merged name list is cached in the 'struct file' and so remains as long as the file is kept open. If the directory is opened and read by two processes at the same time, they will each have separate caches. A seekdir to the start of the directory (offset 0) followed by a readdir will cause the cache to be discarded and rebuilt. This means that changes to the merged directory do not appear while a directory is being read. This is unlikely to be noticed by many programs. seek offsets are assigned sequentially when the directories are read. Thus if - read part of a directory - remember an offset, and close the directory - re-open the directory some time later - seek to the remembered offset there may be little correlation between the old and new locations in the list of filenames, particularly if anything has changed in the directory. Readdir on directories that are not merged is simply handled by the underlying directory (upper or lower). renaming directories -------------------- When renaming a directory that is on the lower layer or merged (i.e. the directory was not created on the upper layer to start with) overlayfs can handle it in two different ways: 1. return EXDEV error: this error is returned by rename(2) when trying to move a file or directory across filesystem boundaries. Hence applications are usually prepared to hande this error (mv(1) for example recursively copies the directory tree). This is the default behavior. 2. If the "redirect_dir" feature is enabled, then the directory will be copied up (but not the contents). Then the "trusted.overlay.redirect" extended attribute is set to the path of the original location from the root of the overlay. Finally the directory is moved to the new location. Non-directories --------------- Objects that are not directories (files, symlinks, device-special files etc.) are presented either from the upper or lower filesystem as appropriate. When a file in the lower filesystem is accessed in a way the requires write-access, such as opening for write access, changing some metadata etc., the file is first copied from the lower filesystem to the upper filesystem (copy_up). Note that creating a hard-link also requires copy_up, though of course creation of a symlink does not. The copy_up may turn out to be unnecessary, for example if the file is opened for read-write but the data is not modified. The copy_up process first makes sure that the containing directory exists in the upper filesystem - creating it and any parents as necessary. It then creates the object with the same metadata (owner, mode, mtime, symlink-target etc.) and then if the object is a file, the data is copied from the lower to the upper filesystem. Finally any extended attributes are copied up. Once the copy_up is complete, the overlay filesystem simply provides direct access to the newly created file in the upper filesystem - future operations on the file are barely noticed by the overlay filesystem (though an operation on the name of the file such as rename or unlink will of course be noticed and handled). Multiple lower layers --------------------- Multiple lower layers can now be given using the the colon (":") as a separator character between the directory names. For example: mount -t overlay overlay -olowerdir=/lower1:/lower2:/lower3 /merged As the example shows, "upperdir=" and "workdir=" may be omitted. In that case the overlay will be read-only. The specified lower directories will be stacked beginning from the rightmost one and going left. In the above example lower1 will be the top, lower2 the middle and lower3 the bottom layer. Non-standard behavior --------------------- The copy_up operation essentially creates a new, identical file and moves it over to the old name. The new file may be on a different filesystem, so both st_dev and st_ino of the file may change. Any open files referring to this inode will access the old data. If a file with multiple hard links is copied up, then this will "break" the link. Changes will not be propagated to other names referring to the same inode. Unless "redirect_dir" feature is enabled, rename(2) on a lower or merged directory will fail with EXDEV. Changes to underlying filesystems --------------------------------- Offline changes, when the overlay is not mounted, are allowed to either the upper or the lower trees. Changes to the underlying filesystems while part of a mounted overlay filesystem are not allowed. If the underlying filesystem is changed, the behavior of the overlay is undefined, though it will not result in a crash or deadlock. Testsuite --------- There's testsuite developed by David Howells at: git://git.infradead.org/users/dhowells/unionmount-testsuite.git Run as root: # cd unionmount-testsuite # ./run --ov