drivers/usb/serial/digi_acceleport.c

   1 /*
   2 *  Digi AccelePort USB-4 and USB-2 Serial Converters
   3 *
   4 *  Copyright 2000 by Digi International
   5 *
   6 *  This program is free software; you can redistribute it and/or modify
   7 *  it under the terms of the GNU General Public License as published by
   8 *  the Free Software Foundation; either version 2 of the License, or
   9 *  (at your option) any later version.
  10 *
  11 *  Shamelessly based on Brian Warner's keyspan_pda.c and Greg Kroah-Hartman's
  12 *  usb-serial driver.
  13 *
  14 *  Peter Berger (pberger@brimson.com)
  15 *  Al Borchers (borchers@steinerpoint.com)
  16 *
  17 * (12/03/2001) gkh
  18 *       switched to using port->open_count instead of private version.
  19 *       Removed port->active
  20 *
  21 * (04/08/2001) gb
  22 *       Identify version on module load.
  23 *
  24 * (11/01/2000) Adam J. Richter
  25 *       usb_device_id table support
  26 *
  27 * (11/01/2000) pberger and borchers
  28 *    -- Turned off the USB_DISABLE_SPD flag for write bulk urbs--it caused
  29 *       USB 4 ports to hang on startup.
  30 *    -- Serialized access to write urbs by adding the dp_write_urb_in_use
  31 *       flag; otherwise, the driver caused SMP system hangs.  Watching the
  32 *       urb status is not sufficient.
  33 *
  34 * (10/05/2000) gkh
  35 *    -- Fixed bug with urb->dev not being set properly, now that the usb
  36 *       core needs it.
  37 *
  38 *  (8/8/2000) pberger and borchers
  39 *    -- Fixed close so that
  40 *       - it can timeout while waiting for transmit idle, if needed;
  41 *       - it ignores interrupts when flushing the port, turning
  42 *         of modem signalling, and so on;
  43 *       - it waits for the flush to really complete before returning.
  44 *    -- Read_bulk_callback and write_bulk_callback check for a closed
  45 *       port before using the tty struct or writing to the port.
  46 *    -- The two changes above fix the oops caused by interrupted closes.
  47 *    -- Added interruptible args to write_oob_command and set_modem_signals
  48 *       and added a timeout arg to transmit_idle; needed for fixes to
  49 *       close.
  50 *    -- Added code for rx_throttle and rx_unthrottle so that input flow
  51 *       control works.
  52 *    -- Added code to set overrun, parity, framing, and break errors
  53 *       (untested).
  54 *    -- Set USB_DISABLE_SPD flag for write bulk urbs, so no 0 length
  55 *       bulk writes are done.  These hung the Digi USB device.  The
  56 *       0 length bulk writes were a new feature of usb-uhci added in
  57 *       the 2.4.0-test6 kernels.
  58 *    -- Fixed mod inc race in open; do mod inc before sleeping to wait
  59 *       for a close to finish.
  60 *
  61 *  (7/31/2000) pberger
  62 *    -- Fixed bugs with hardware handshaking:
  63 *       - Added code to set/clear tty->hw_stopped in digi_read_oob_callback()
  64 *         and digi_set_termios()
  65 *    -- Added code in digi_set_termios() to
  66 *       - add conditional in code handling transition from B0 to only
  67 *         set RTS if RTS/CTS flow control is either not in use or if
  68 *         the port is not currently throttled.
  69 *       - handle turning off CRTSCTS.
  70 *
  71 *  (7/30/2000) borchers
  72 *    -- Added support for more than one Digi USB device by moving
  73 *       globals to a private structure in the pointed to from the
  74 *       usb_serial structure.
  75 *    -- Moved the modem change and transmit idle wait queues into
  76 *       the port private structure, so each port has its own queue
  77 *       rather than sharing global queues.
  78 *    -- Added support for break signals.
  79 *
  80 *  (7/25/2000) pberger
  81 *    -- Added USB-2 support.  Note: the USB-2 supports 3 devices: two
  82 *       serial and a parallel port.  The parallel port is implemented
  83 *       as a serial-to-parallel converter.  That is, the driver actually
  84 *       presents all three USB-2 interfaces as serial ports, but the third
  85 *       one physically connects to a parallel device.  Thus, for example,
  86 *       one could plug a parallel printer into the USB-2's third port,
  87 *       but from the kernel's (and userland's) point of view what's
  88 *       actually out there is a serial device.
  89 *
  90 *  (7/15/2000) borchers
  91 *    -- Fixed race in open when a close is in progress.
  92 *    -- Keep count of opens and dec the module use count for each
  93 *       outstanding open when shutdown is called (on disconnect).
  94 *    -- Fixed sanity checks in read_bulk_callback and write_bulk_callback
  95 *       so pointers are checked before use.
  96 *    -- Split read bulk callback into in band and out of band
  97 *       callbacks, and no longer restart read chains if there is
  98 *       a status error or a sanity error.  This fixed the seg
  99 *       faults and other errors we used to get on disconnect.
 100 *    -- Port->active is once again a flag as usb-serial intended it
 101 *       to be, not a count.  Since it was only a char it would
 102 *       have been limited to 256 simultaneous opens.  Now the open
 103 *       count is kept in the port private structure in dp_open_count.
 104 *    -- Added code for modularization of the digi_acceleport driver.
 105 *
 106 *  (6/27/2000) pberger and borchers
 107 *    -- Zeroed out sync field in the wakeup_task before first use;
 108 *       otherwise the uninitialized value might prevent the task from
 109 *       being scheduled.
 110 *    -- Initialized ret value to 0 in write_bulk_callback, otherwise
 111 *       the uninitialized value could cause a spurious debugging message.
 112 *
 113 *  (6/22/2000) pberger and borchers
 114 *    -- Made cond_wait_... inline--apparently on SPARC the flags arg
 115 *       to spin_lock_irqsave cannot be passed to another function
 116 *       to call spin_unlock_irqrestore.  Thanks to Pauline Middelink.
 117 *    -- In digi_set_modem_signals the inner nested spin locks use just
 118 *       spin_lock() rather than spin_lock_irqsave().  The old code
 119 *       mistakenly left interrupts off.  Thanks to Pauline Middelink.
 120 *    -- copy_from_user (which can sleep) is no longer called while a
 121 *       spinlock is held.  We copy to a local buffer before getting
 122 *       the spinlock--don't like the extra copy but the code is simpler.
 123 *    -- Printk and dbg are no longer called while a spin lock is held.
 124 *
 125 *  (6/4/2000) pberger and borchers
 126 *    -- Replaced separate calls to spin_unlock_irqrestore and
 127 *       interruptible_sleep_on_timeout with a new function
 128 *       cond_wait_interruptible_timeout_irqrestore.  This eliminates
 129 *       the race condition where the wake up could happen after
 130 *       the unlock and before the sleep.
 131 *    -- Close now waits for output to drain.
 132 *    -- Open waits until any close in progress is finished.
 133 *    -- All out of band responses are now processed, not just the
 134 *       first in a USB packet.
 135 *    -- Fixed a bug that prevented the driver from working when the
 136 *       first Digi port was not the first USB serial port--the driver
 137 *       was mistakenly using the external USB serial port number to
 138 *       try to index into its internal ports.
 139 *    -- Fixed an SMP bug -- write_bulk_callback is called directly from
 140 *       an interrupt, so spin_lock_irqsave/spin_unlock_irqrestore are
 141 *       needed for locks outside write_bulk_callback that are also
 142 *       acquired by write_bulk_callback to prevent deadlocks.
 143 *    -- Fixed support for select() by making digi_chars_in_buffer()
 144 *       return 256 when -EINPROGRESS is set, as the line discipline
 145 *       code in n_tty.c expects.
 146 *    -- Fixed an include file ordering problem that prevented debugging
 147 *       messages from working.
 148 *    -- Fixed an intermittent timeout problem that caused writes to
 149 *       sometimes get stuck on some machines on some kernels.  It turns
 150 *       out in these circumstances write_chan() (in n_tty.c) was
 151 *       asleep waiting for our wakeup call.  Even though we call
 152 *       wake_up_interruptible() in digi_write_bulk_callback(), there is
 153 *       a race condition that could cause the wakeup to fail: if our
 154 *       wake_up_interruptible() call occurs between the time that our
 155 *       driver write routine finishes and write_chan() sets current->state
 156 *       to TASK_INTERRUPTIBLE, the effect of our wakeup setting the state
 157 *       to TASK_RUNNING will be lost and write_chan's subsequent call to
 158 *       schedule() will never return (unless it catches a signal).
 159 *       This race condition occurs because write_bulk_callback() (and thus
 160 *       the wakeup) are called asynchonously from an interrupt, rather than
 161 *       from the scheduler.  We can avoid the race by calling the wakeup
 162 *       from the scheduler queue and that's our fix:  Now, at the end of
 163 *       write_bulk_callback() we queue up a wakeup call on the scheduler
 164 *       task queue.  We still also invoke the wakeup directly since that
 165 *       squeezes a bit more performance out of the driver, and any lost
 166 *       race conditions will get cleaned up at the next scheduler run.
 167 *
 168 *       NOTE:  The problem also goes away if you comment out
 169 *       the two code lines in write_chan() where current->state
 170 *       is set to TASK_RUNNING just before calling driver.write() and to
 171 *       TASK_INTERRUPTIBLE immediately afterwards.  This is why the
 172 *       problem did not show up with the 2.2 kernels -- they do not
 173 *       include that code.
 174 *
 175 *  (5/16/2000) pberger and borchers
 176 *    -- Added timeouts to sleeps, to defend against lost wake ups.
 177 *    -- Handle transition to/from B0 baud rate in digi_set_termios.
 178 *
 179 *  (5/13/2000) pberger and borchers
 180 *    -- All commands now sent on out of band port, using
 181 *       digi_write_oob_command.
 182 *    -- Get modem control signals whenever they change, support TIOCMGET/
 183 *       SET/BIS/BIC ioctls.
 184 *    -- digi_set_termios now supports parity, word size, stop bits, and
 185 *       receive enable.
 186 *    -- Cleaned up open and close, use digi_set_termios and
 187 *       digi_write_oob_command to set port parameters.
 188 *    -- Added digi_startup_device to start read chains on all ports.
 189 *    -- Write buffer is only used when count==1, to be sure put_char can
 190 *       write a char (unless the buffer is full).
 191 *
 192 *  (5/10/2000) pberger and borchers
 193 *    -- Added MOD_INC_USE_COUNT/MOD_DEC_USE_COUNT calls on open/close.
 194 *    -- Fixed problem where the first incoming character is lost on
 195 *       port opens after the first close on that port.  Now we keep
 196 *       the read_urb chain open until shutdown.
 197 *    -- Added more port conditioning calls in digi_open and digi_close.
 198 *    -- Convert port->active to a use count so that we can deal with multiple
 199 *       opens and closes properly.
 200 *    -- Fixed some problems with the locking code.
 201 *
 202 *  (5/3/2000) pberger and borchers
 203 *    -- First alpha version of the driver--many known limitations and bugs.
 204 *
 205 *
 206 *  Locking and SMP
 207 *
 208 *  - Each port, including the out-of-band port, has a lock used to
 209 *    serialize all access to the port's private structure.
 210 *  - The port lock is also used to serialize all writes and access to
 211 *    the port's URB.
 212 *  - The port lock is also used for the port write_wait condition
 213 *    variable.  Holding the port lock will prevent a wake up on the
 214 *    port's write_wait; this can be used with cond_wait_... to be sure
 215 *    the wake up is not lost in a race when dropping the lock and
 216 *    sleeping waiting for the wakeup.
 217 *  - digi_write() does not sleep, since it is sometimes called on
 218 *    interrupt time.
 219 *  - digi_write_bulk_callback() and digi_read_bulk_callback() are
 220 *    called directly from interrupts.  Hence spin_lock_irqsave()
 221 *    and spin_unlock_irqrestore() are used in the rest of the code
 222 *    for any locks they acquire.
 223 *  - digi_write_bulk_callback() gets the port lock before waking up
 224 *    processes sleeping on the port write_wait.  It also schedules
 225 *    wake ups so they happen from the scheduler, because the tty
 226 *    system can miss wake ups from interrupts.
 227 *  - All sleeps use a timeout of DIGI_RETRY_TIMEOUT before looping to
 228 *    recheck the condition they are sleeping on.  This is defensive,
 229 *    in case a wake up is lost.
 230 *  - Following Documentation/DocBook/kernel-locking.pdf no spin locks
 231 *    are held when calling copy_to/from_user or printk.
 232 *
 233 *  $Id: digi_acceleport.c,v 1.80.1.2 2000/11/02 05:45:08 root Exp $
 234 */
 235
 236 #include <linux/kernel.h>
 237 #include <linux/errno.h>
 238 #include <linux/init.h>
 239 #include <linux/slab.h>
 240 #include <linux/tty.h>
 241 #include <linux/tty_driver.h>
 242 #include <linux/tty_flip.h>
 243 #include <linux/module.h>
 244 #include <linux/spinlock.h>
 245 #include <linux/workqueue.h>
 246 #include <asm/uaccess.h>
 247 #include <linux/usb.h>
 248 #include <linux/wait.h>
 249 #include <linux/usb/serial.h>
 250
 251 /* Defines */
 252
 253 /*
 254  * Version Information
 255  */
 256 #define DRIVER_VERSION "v1.80.1.2"
 257 #define DRIVER_AUTHOR "Peter Berger <pberger@brimson.com>, Al Borchers <borchers@steinerpoint.com>"
 258 #define DRIVER_DESC "Digi AccelePort USB-2/USB-4 Serial Converter driver"
 259
 260 /* port output buffer length -- must be <= transfer buffer length - 2 */
 261 /* so we can be sure to send the full buffer in one urb */
 262 #define DIGI_OUT_BUF_SIZE               8
 263
 264 /* port input buffer length -- must be >= transfer buffer length - 3 */
 265 /* so we can be sure to hold at least one full buffer from one urb */
 266 #define DIGI_IN_BUF_SIZE                64
 267
 268 /* retry timeout while sleeping */
 269 #define DIGI_RETRY_TIMEOUT              (HZ/10)
 270
 271 /* timeout while waiting for tty output to drain in close */
 272 /* this delay is used twice in close, so the total delay could */
 273 /* be twice this value */
 274 #define DIGI_CLOSE_TIMEOUT              (5*HZ)
 275
 276
 277 /* AccelePort USB Defines */
 278
 279 /* ids */
 280 #define DIGI_VENDOR_ID                  0x05c5
 281 #define DIGI_2_ID                       0x0002  /* USB-2 */
 282 #define DIGI_4_ID                       0x0004  /* USB-4 */
 283
 284 /* commands
 285  * "INB": can be used on the in-band endpoint
 286  * "OOB": can be used on the out-of-band endpoint
 287  */
 288 #define DIGI_CMD_SET_BAUD_RATE                  0       /* INB, OOB */
 289 #define DIGI_CMD_SET_WORD_SIZE                  1       /* INB, OOB */
 290 #define DIGI_CMD_SET_PARITY                     2       /* INB, OOB */
 291 #define DIGI_CMD_SET_STOP_BITS                  3       /* INB, OOB */
 292 #define DIGI_CMD_SET_INPUT_FLOW_CONTROL         4       /* INB, OOB */
 293 #define DIGI_CMD_SET_OUTPUT_FLOW_CONTROL        5       /* INB, OOB */
 294 #define DIGI_CMD_SET_DTR_SIGNAL                 6       /* INB, OOB */
 295 #define DIGI_CMD_SET_RTS_SIGNAL                 7       /* INB, OOB */
 296 #define DIGI_CMD_READ_INPUT_SIGNALS             8       /*      OOB */
 297 #define DIGI_CMD_IFLUSH_FIFO                    9       /*      OOB */
 298 #define DIGI_CMD_RECEIVE_ENABLE                 10      /* INB, OOB */
 299 #define DIGI_CMD_BREAK_CONTROL                  11      /* INB, OOB */
 300 #define DIGI_CMD_LOCAL_LOOPBACK                 12      /* INB, OOB */
 301 #define DIGI_CMD_TRANSMIT_IDLE                  13      /* INB, OOB */
 302 #define DIGI_CMD_READ_UART_REGISTER             14      /*      OOB */
 303 #define DIGI_CMD_WRITE_UART_REGISTER            15      /* INB, OOB */
 304 #define DIGI_CMD_AND_UART_REGISTER              16      /* INB, OOB */
 305 #define DIGI_CMD_OR_UART_REGISTER               17      /* INB, OOB */
 306 #define DIGI_CMD_SEND_DATA                      18      /* INB      */
 307 #define DIGI_CMD_RECEIVE_DATA                   19      /* INB      */
 308 #define DIGI_CMD_RECEIVE_DISABLE                20      /* INB      */
 309 #define DIGI_CMD_GET_PORT_TYPE                  21      /*      OOB */
 310
 311 /* baud rates */
 312 #define DIGI_BAUD_50                            0
 313 #define DIGI_BAUD_75                            1
 314 #define DIGI_BAUD_110                           2
 315 #define DIGI_BAUD_150                           3
 316 #define DIGI_BAUD_200                           4
 317 #define DIGI_BAUD_300                           5
 318 #define DIGI_BAUD_600                           6
 319 #define DIGI_BAUD_1200                          7
 320 #define DIGI_BAUD_1800                          8
 321 #define DIGI_BAUD_2400                          9
 322 #define DIGI_BAUD_4800                          10
 323 #define DIGI_BAUD_7200                          11
 324 #define DIGI_BAUD_9600                          12
 325 #define DIGI_BAUD_14400                         13
 326 #define DIGI_BAUD_19200                         14
 327 #define DIGI_BAUD_28800                         15
 328 #define DIGI_BAUD_38400                         16
 329 #define DIGI_BAUD_57600                         17
 330 #define DIGI_BAUD_76800                         18
 331 #define DIGI_BAUD_115200                        19
 332 #define DIGI_BAUD_153600                        20
 333 #define DIGI_BAUD_230400                        21
 334 #define DIGI_BAUD_460800                        22
 335
 336 /* arguments */
 337 #define DIGI_WORD_SIZE_5                        0
 338 #define DIGI_WORD_SIZE_6                        1
 339 #define DIGI_WORD_SIZE_7                        2
 340 #define DIGI_WORD_SIZE_8                        3
 341
 342 #define DIGI_PARITY_NONE                        0
 343 #define DIGI_PARITY_ODD                         1
 344 #define DIGI_PARITY_EVEN                        2
 345 #define DIGI_PARITY_MARK                        3
 346 #define DIGI_PARITY_SPACE                       4
 347
 348 #define DIGI_STOP_BITS_1                        0
 349 #define DIGI_STOP_BITS_2                        1
 350
 351 #define DIGI_INPUT_FLOW_CONTROL_XON_XOFF        1
 352 #define DIGI_INPUT_FLOW_CONTROL_RTS             2
 353 #define DIGI_INPUT_FLOW_CONTROL_DTR             4
 354
 355 #define DIGI_OUTPUT_FLOW_CONTROL_XON_XOFF       1
 356 #define DIGI_OUTPUT_FLOW_CONTROL_CTS            2
 357 #define DIGI_OUTPUT_FLOW_CONTROL_DSR            4
 358
 359 #define DIGI_DTR_INACTIVE                       0
 360 #define DIGI_DTR_ACTIVE                         1
 361 #define DIGI_DTR_INPUT_FLOW_CONTROL             2
 362
 363 #define DIGI_RTS_INACTIVE                       0
 364 #define DIGI_RTS_ACTIVE                         1
 365 #define DIGI_RTS_INPUT_FLOW_CONTROL             2
 366 #define DIGI_RTS_TOGGLE                         3
 367
 368 #define DIGI_FLUSH_TX                           1
 369 #define DIGI_FLUSH_RX                           2
 370 #define DIGI_RESUME_TX                          4 /* clears xoff condition */
 371
 372 #define DIGI_TRANSMIT_NOT_IDLE                  0
 373 #define DIGI_TRANSMIT_IDLE                      1
 374
 375 #define DIGI_DISABLE                            0
 376 #define DIGI_ENABLE                             1
 377
 378 #define DIGI_DEASSERT                           0
 379 #define DIGI_ASSERT                             1
 380
 381 /* in band status codes */
 382 #define DIGI_OVERRUN_ERROR                      4
 383 #define DIGI_PARITY_ERROR                       8
 384 #define DIGI_FRAMING_ERROR                      16
 385 #define DIGI_BREAK_ERROR                        32
 386
 387 /* out of band status */
 388 #define DIGI_NO_ERROR                           0
 389 #define DIGI_BAD_FIRST_PARAMETER                1
 390 #define DIGI_BAD_SECOND_PARAMETER               2
 391 #define DIGI_INVALID_LINE                       3
 392 #define DIGI_INVALID_OPCODE                     4
 393
 394 /* input signals */
 395 #define DIGI_READ_INPUT_SIGNALS_SLOT            1
 396 #define DIGI_READ_INPUT_SIGNALS_ERR             2
 397 #define DIGI_READ_INPUT_SIGNALS_BUSY            4
 398 #define DIGI_READ_INPUT_SIGNALS_PE              8
 399 #define DIGI_READ_INPUT_SIGNALS_CTS             16
 400 #define DIGI_READ_INPUT_SIGNALS_DSR             32
 401 #define DIGI_READ_INPUT_SIGNALS_RI              64
 402 #define DIGI_READ_INPUT_SIGNALS_DCD             128
 403
 404
 405 /* Structures */
 406
 407 struct digi_serial {
 408         spinlock_t ds_serial_lock;
 409         struct usb_serial_port *ds_oob_port;    /* out-of-band port */
 410         int ds_oob_port_num;                    /* index of out-of-band port */
 411         int ds_device_started;
 412 };
 413
 414 struct digi_port {
 415         spinlock_t dp_port_lock;
 416         int dp_port_num;
 417         int dp_out_buf_len;
 418         unsigned char dp_out_buf[DIGI_OUT_BUF_SIZE];
 419         int dp_in_buf_len;
 420         unsigned char dp_in_buf[DIGI_IN_BUF_SIZE];
 421         unsigned char dp_in_flag_buf[DIGI_IN_BUF_SIZE];
 422         int dp_write_urb_in_use;
 423         unsigned int dp_modem_signals;
 424         wait_queue_head_t dp_modem_change_wait;
 425         int dp_transmit_idle;
 426         wait_queue_head_t dp_transmit_idle_wait;
 427         int dp_throttled;
 428         int dp_throttle_restart;
 429         wait_queue_head_t dp_flush_wait;
 430         int dp_in_close;                        /* close in progress */
 431         wait_queue_head_t dp_close_wait;        /* wait queue for close */
 432         struct work_struct dp_wakeup_work;
 433 };
 434
 435
 436 /* Local Function Declarations */
 437
 438 static void digi_wakeup_write( struct usb_serial_port *port );
 439 static void digi_wakeup_write_lock(void *);
 440 static int digi_write_oob_command( struct usb_serial_port *port,
 441         unsigned char *buf, int count, int interruptible );
 442 static int digi_write_inb_command( struct usb_serial_port *port,
 443         unsigned char *buf, int count, unsigned long timeout );
 444 static int digi_set_modem_signals( struct usb_serial_port *port,
 445         unsigned int modem_signals, int interruptible );
 446 static int digi_transmit_idle( struct usb_serial_port *port,
 447         unsigned long timeout );
 448 static void digi_rx_throttle (struct usb_serial_port *port);
 449 static void digi_rx_unthrottle (struct usb_serial_port *port);
 450 static void digi_set_termios( struct usb_serial_port *port,
 451         struct termios *old_termios );
 452 static void digi_break_ctl( struct usb_serial_port *port, int break_state );
 453 static int digi_ioctl( struct usb_serial_port *port, struct file *file,
 454         unsigned int cmd, unsigned long arg );
 455 static int digi_tiocmget( struct usb_serial_port *port, struct file *file );
 456 static int digi_tiocmset( struct usb_serial_port *port, struct file *file,
 457         unsigned int set, unsigned int clear );
 458 static int digi_write( struct usb_serial_port *port, const unsigned char *buf, int count );
 459 static void digi_write_bulk_callback( struct urb *urb );
 460 static int digi_write_room( struct usb_serial_port *port );
 461 static int digi_chars_in_buffer( struct usb_serial_port *port );
 462 static int digi_open( struct usb_serial_port *port, struct file *filp );
 463 static void digi_close( struct usb_serial_port *port, struct file *filp );
 464 static int digi_startup_device( struct usb_serial *serial );
 465 static int digi_startup( struct usb_serial *serial );
 466 static void digi_shutdown( struct usb_serial *serial );
 467 static void digi_read_bulk_callback( struct urb *urb );
 468 static int digi_read_inb_callback( struct urb *urb );
 469 static int digi_read_oob_callback( struct urb *urb );
 470
 471
 472 /* Statics */
 473
 474 static int debug;
 475
 476 static struct usb_device_id id_table_combined [] = {
 477         { USB_DEVICE(DIGI_VENDOR_ID, DIGI_2_ID) },
 478         { USB_DEVICE(DIGI_VENDOR_ID, DIGI_4_ID) },
 479         { }                                             /* Terminating entry */
 480 };
 481
 482 static struct usb_device_id id_table_2 [] = {
 483         { USB_DEVICE(DIGI_VENDOR_ID, DIGI_2_ID) },
 484         { }                                             /* Terminating entry */
 485 };
 486
 487 static struct usb_device_id id_table_4 [] = {
 488         { USB_DEVICE(DIGI_VENDOR_ID, DIGI_4_ID) },
 489         { }                                             /* Terminating entry */
 490 };
 491
 492 MODULE_DEVICE_TABLE (usb, id_table_combined);
 493
 494 static struct usb_driver digi_driver = {
 495         .name =         "digi_acceleport",
 496         .probe =        usb_serial_probe,
 497         .disconnect =   usb_serial_disconnect,
 498         .id_table =     id_table_combined,
 499         .no_dynamic_id =        1,
 500 };
 501
 502
 503 /* device info needed for the Digi serial converter */
 504
 505 static struct usb_serial_driver digi_acceleport_2_device = {
 506         .driver = {
 507                 .owner =                THIS_MODULE,
 508                 .name =                 "digi_2",
 509         },
 510         .description =                  "Digi 2 port USB adapter",
 511         .id_table =                     id_table_2,
 512         .num_interrupt_in =             0,
 513         .num_bulk_in =                  4,
 514         .num_bulk_out =                 4,
 515         .num_ports =                    3,
 516         .open =                         digi_open,
 517         .close =                        digi_close,
 518         .write =                        digi_write,
 519         .write_room =                   digi_write_room,
 520         .write_bulk_callback =          digi_write_bulk_callback,
 521         .read_bulk_callback =           digi_read_bulk_callback,
 522         .chars_in_buffer =              digi_chars_in_buffer,
 523         .throttle =                     digi_rx_throttle,
 524         .unthrottle =                   digi_rx_unthrottle,
 525         .ioctl =                        digi_ioctl,
 526         .set_termios =                  digi_set_termios,
 527         .break_ctl =                    digi_break_ctl,
 528         .tiocmget =                     digi_tiocmget,
 529         .tiocmset =                     digi_tiocmset,
 530         .attach =                       digi_startup,
 531         .shutdown =                     digi_shutdown,
 532 };
 533
 534 static struct usb_serial_driver digi_acceleport_4_device = {
 535         .driver = {
 536                 .owner =                THIS_MODULE,
 537                 .name =                 "digi_4",
 538         },
 539         .description =                  "Digi 4 port USB adapter",
 540         .id_table =                     id_table_4,
 541         .num_interrupt_in =             0,
 542         .num_bulk_in =                  5,
 543         .num_bulk_out =                 5,
 544         .num_ports =                    4,
 545         .open =                         digi_open,
 546         .close =                        digi_close,
 547         .write =                        digi_write,
 548         .write_room =                   digi_write_room,
 549         .write_bulk_callback =          digi_write_bulk_callback,
 550         .read_bulk_callback =           digi_read_bulk_callback,
 551         .chars_in_buffer =              digi_chars_in_buffer,
 552         .throttle =                     digi_rx_throttle,
 553         .unthrottle =                   digi_rx_unthrottle,
 554         .ioctl =                        digi_ioctl,
 555         .set_termios =                  digi_set_termios,
 556         .break_ctl =                    digi_break_ctl,
 557         .tiocmget =                     digi_tiocmget,
 558         .tiocmset =                     digi_tiocmset,
 559         .attach =                       digi_startup,
 560         .shutdown =                     digi_shutdown,
 561 };
 562
 563
 564 /* Functions */
 565
 566 /*
 567 *  Cond Wait Interruptible Timeout Irqrestore
 568 *
 569 *  Do spin_unlock_irqrestore and interruptible_sleep_on_timeout
 570 *  so that wake ups are not lost if they occur between the unlock
 571 *  and the sleep.  In other words, spin_unlock_irqrestore and
 572 *  interruptible_sleep_on_timeout are "atomic" with respect to
 573 *  wake ups.  This is used to implement condition variables.
 574 *
 575 *  interruptible_sleep_on_timeout is deprecated and has been replaced
 576 *  with the equivalent code.
 577 */
 578
 579 static inline long cond_wait_interruptible_timeout_irqrestore(
 580         wait_queue_head_t *q, long timeout,
 581         spinlock_t *lock, unsigned long flags )
 582 {
 583         DEFINE_WAIT(wait);
 584
 585         prepare_to_wait(q, &wait, TASK_INTERRUPTIBLE);
 586         spin_unlock_irqrestore(lock, flags);
 587         timeout = schedule_timeout(timeout);
 588         finish_wait(q, &wait);
 589
 590         return timeout;
 591 }
 592
 593
 594 /*
 595 *  Digi Wakeup Write
 596 *
 597 *  Wake up port, line discipline, and tty processes sleeping
 598 *  on writes.
 599 */
 600
 601 static void digi_wakeup_write_lock(void *arg)
 602 {
 603         struct usb_serial_port *port = arg;
 604         unsigned long flags;
 605         struct digi_port *priv = usb_get_serial_port_data(port);
 606
 607
 608         spin_lock_irqsave( &priv->dp_port_lock, flags );
 609         digi_wakeup_write( port );
 610         spin_unlock_irqrestore( &priv->dp_port_lock, flags );
 611 }
 612
 613 static void digi_wakeup_write( struct usb_serial_port *port )
 614 {
 615
 616         struct tty_struct *tty = port->tty;
 617
 618
 619         /* wake up port processes */
 620         wake_up_interruptible( &port->write_wait );
 621
 622         /* wake up line discipline */
 623         tty_wakeup(tty);
 624 }
 625
 626
 627 /*
 628 *  Digi Write OOB Command
 629 *
 630 *  Write commands on the out of band port.  Commands are 4
 631 *  bytes each, multiple commands can be sent at once, and
 632 *  no command will be split across USB packets.  Returns 0
 633 *  if successful, -EINTR if interrupted while sleeping and
 634 *  the interruptible flag is true, or a negative error
 635 *  returned by usb_submit_urb.
 636 */
 637
 638 static int digi_write_oob_command( struct usb_serial_port *port,
 639         unsigned char *buf, int count, int interruptible )
 640 {
 641
 642         int ret = 0;
 643         int len;
 644         struct usb_serial_port *oob_port = (struct usb_serial_port *)((struct digi_serial *)(usb_get_serial_data(port->serial)))->ds_oob_port;
 645         struct digi_port *oob_priv = usb_get_serial_port_data(oob_port);
 646         unsigned long flags = 0;
 647
 648
 649 dbg( "digi_write_oob_command: TOP: port=%d, count=%d", oob_priv->dp_port_num, count );
 650
 651         spin_lock_irqsave( &oob_priv->dp_port_lock, flags );
 652
 653         while( count > 0 ) {
 654
 655                 while( oob_port->write_urb->status == -EINPROGRESS
 656                 || oob_priv->dp_write_urb_in_use ) {
 657                         cond_wait_interruptible_timeout_irqrestore(
 658                                 &oob_port->write_wait, DIGI_RETRY_TIMEOUT,
 659                                 &oob_priv->dp_port_lock, flags );
 660                         if( interruptible && signal_pending(current) ) {
 661                                 return( -EINTR );
 662                         }
 663                         spin_lock_irqsave( &oob_priv->dp_port_lock, flags );
 664                 }
 665
 666                 /* len must be a multiple of 4, so commands are not split */
 667                 len = min(count, oob_port->bulk_out_size );
 668                 if( len > 4 )
 669                         len &= ~3;
 670
 671                 memcpy( oob_port->write_urb->transfer_buffer, buf, len );
 672                 oob_port->write_urb->transfer_buffer_length = len;
 673                 oob_port->write_urb->dev = port->serial->dev;
 674
 675                 if( (ret=usb_submit_urb(oob_port->write_urb, GFP_ATOMIC)) == 0 ) {
 676                         oob_priv->dp_write_urb_in_use = 1;
 677                         count -= len;
 678                         buf += len;
 679                 }
 680
 681         }
 682
 683         spin_unlock_irqrestore( &oob_priv->dp_port_lock, flags );
 684
 685         if( ret ) {
 686                 err("%s: usb_submit_urb failed, ret=%d", __FUNCTION__,
 687                         ret );
 688         }
 689
 690         return( ret );
 691
 692 }
 693
 694
 695 /*
 696 *  Digi Write In Band Command
 697 *
 698 *  Write commands on the given port.  Commands are 4
 699 *  bytes each, multiple commands can be sent at once, and
 700 *  no command will be split across USB packets.  If timeout
 701 *  is non-zero, write in band command will return after
 702 *  waiting unsuccessfully for the URB status to clear for
 703 *  timeout ticks.  Returns 0 if successful, or a negative
 704 *  error returned by digi_write.
 705 */
 706
 707 static int digi_write_inb_command( struct usb_serial_port *port,
 708         unsigned char *buf, int count, unsigned long timeout )
 709 {
 710
 711         int ret = 0;
 712         int len;
 713         struct digi_port *priv = usb_get_serial_port_data(port);
 714         unsigned char *data = port->write_urb->transfer_buffer;
 715         unsigned long flags = 0;
 716
 717
 718 dbg( "digi_write_inb_command: TOP: port=%d, count=%d", priv->dp_port_num,
 719 count );
 720
 721         if( timeout )
 722                 timeout += jiffies;
 723         else
 724                 timeout = ULONG_MAX;
 725
 726         spin_lock_irqsave( &priv->dp_port_lock, flags );
 727
 728         while( count > 0 && ret == 0 ) {
 729
 730                 while( (port->write_urb->status == -EINPROGRESS
 731                 || priv->dp_write_urb_in_use) && time_before(jiffies, timeout)) {
 732                         cond_wait_interruptible_timeout_irqrestore(
 733                                 &port->write_wait, DIGI_RETRY_TIMEOUT,
 734                                 &priv->dp_port_lock, flags );
 735                         if( signal_pending(current) ) {
 736                                 return( -EINTR );
 737                         }
 738                         spin_lock_irqsave( &priv->dp_port_lock, flags );
 739                 }
 740
 741                 /* len must be a multiple of 4 and small enough to */
 742                 /* guarantee the write will send buffered data first, */
 743                 /* so commands are in order with data and not split */
 744                 len = min(count, port->bulk_out_size-2-priv->dp_out_buf_len );
 745                 if( len > 4 )
 746                         len &= ~3;
 747
 748                 /* write any buffered data first */
 749                 if( priv->dp_out_buf_len > 0 ) {
 750                         data[0] = DIGI_CMD_SEND_DATA;
 751                         data[1] = priv->dp_out_buf_len;
 752                         memcpy( data+2, priv->dp_out_buf,
 753                                 priv->dp_out_buf_len );
 754                         memcpy( data+2+priv->dp_out_buf_len, buf, len );
 755                         port->write_urb->transfer_buffer_length
 756                                 = priv->dp_out_buf_len+2+len;
 757                 } else {
 758                         memcpy( data, buf, len );
 759                         port->write_urb->transfer_buffer_length = len;
 760                 }
 761                 port->write_urb->dev = port->serial->dev;
 762
 763                 if( (ret=usb_submit_urb(port->write_urb, GFP_ATOMIC)) == 0 ) {
 764                         priv->dp_write_urb_in_use = 1;
 765                         priv->dp_out_buf_len = 0;
 766                         count -= len;
 767                         buf += len;
 768                 }
 769
 770         }
 771
 772         spin_unlock_irqrestore( &priv->dp_port_lock, flags );
 773
 774         if( ret ) {
 775                 err("%s: usb_submit_urb failed, ret=%d, port=%d", __FUNCTION__,
 776                 ret, priv->dp_port_num );
 777         }
 778
 779         return( ret );
 780
 781 }
 782
 783
 784 /*
 785 *  Digi Set Modem Signals
 786 *
 787 *  Sets or clears DTR and RTS on the port, according to the
 788 *  modem_signals argument.  Use TIOCM_DTR and TIOCM_RTS flags
 789 *  for the modem_signals argument.  Returns 0 if successful,
 790 *  -EINTR if interrupted while sleeping, or a non-zero error
 791 *  returned by usb_submit_urb.
 792 */
 793
 794 static int digi_set_modem_signals( struct usb_serial_port *port,
 795         unsigned int modem_signals, int interruptible )
 796 {
 797
 798         int ret;
 799         struct digi_port *port_priv = usb_get_serial_port_data(port);
 800         struct usb_serial_port *oob_port = (struct usb_serial_port *)((struct digi_serial *)(usb_get_serial_data(port->serial)))->ds_oob_port;
 801         struct digi_port *oob_priv = usb_get_serial_port_data(oob_port);
 802         unsigned char *data = oob_port->write_urb->transfer_buffer;
 803         unsigned long flags = 0;
 804
 805
 806 dbg( "digi_set_modem_signals: TOP: port=%d, modem_signals=0x%x",
 807 port_priv->dp_port_num, modem_signals );
 808
 809         spin_lock_irqsave( &oob_priv->dp_port_lock, flags );
 810         spin_lock( &port_priv->dp_port_lock );
 811
 812         while( oob_port->write_urb->status == -EINPROGRESS
 813         || oob_priv->dp_write_urb_in_use ) {
 814                 spin_unlock( &port_priv->dp_port_lock );
 815                 cond_wait_interruptible_timeout_irqrestore(
 816                         &oob_port->write_wait, DIGI_RETRY_TIMEOUT,
 817                         &oob_priv->dp_port_lock, flags );
 818                 if( interruptible && signal_pending(current) ) {
 819                         return( -EINTR );
 820                 }
 821                 spin_lock_irqsave( &oob_priv->dp_port_lock, flags );
 822                 spin_lock( &port_priv->dp_port_lock );
 823         }
 824
 825         data[0] = DIGI_CMD_SET_DTR_SIGNAL;
 826         data[1] = port_priv->dp_port_num;
 827         data[2] = (modem_signals&TIOCM_DTR) ?
 828                 DIGI_DTR_ACTIVE : DIGI_DTR_INACTIVE;
 829         data[3] = 0;
 830
 831         data[4] = DIGI_CMD_SET_RTS_SIGNAL;
 832         data[5] = port_priv->dp_port_num;
 833         data[6] = (modem_signals&TIOCM_RTS) ?
 834                 DIGI_RTS_ACTIVE : DIGI_RTS_INACTIVE;
 835         data[7] = 0;
 836
 837         oob_port->write_urb->transfer_buffer_length = 8;
 838         oob_port->write_urb->dev = port->serial->dev;
 839
 840         if( (ret=usb_submit_urb(oob_port->write_urb, GFP_ATOMIC)) == 0 ) {
 841                 oob_priv->dp_write_urb_in_use = 1;
 842                 port_priv->dp_modem_signals =
 843                         (port_priv->dp_modem_signals&~(TIOCM_DTR|TIOCM_RTS))
 844                         | (modem_signals&(TIOCM_DTR|TIOCM_RTS));
 845         }
 846
 847         spin_unlock( &port_priv->dp_port_lock );
 848         spin_unlock_irqrestore( &oob_priv->dp_port_lock, flags );
 849
 850         if( ret ) {
 851                 err("%s: usb_submit_urb failed, ret=%d", __FUNCTION__,
 852                 ret );
 853         }
 854
 855         return( ret );
 856
 857 }
 858
 859
 860 /*
 861 *  Digi Transmit Idle
 862 *
 863 *  Digi transmit idle waits, up to timeout ticks, for the transmitter
 864 *  to go idle.  It returns 0 if successful or a negative error.
 865 *
 866 *  There are race conditions here if more than one process is calling
 867 *  digi_transmit_idle on the same port at the same time.  However, this
 868 *  is only called from close, and only one process can be in close on a
 869 *  port at a time, so its ok.
 870 */
 871
 872 static int digi_transmit_idle( struct usb_serial_port *port,
 873         unsigned long timeout )
 874 {
 875
 876         int ret;
 877         unsigned char buf[2];
 878         struct digi_port *priv = usb_get_serial_port_data(port);
 879         unsigned long flags = 0;
 880
 881
 882         spin_lock_irqsave( &priv->dp_port_lock, flags );
 883         priv->dp_transmit_idle = 0;
 884         spin_unlock_irqrestore( &priv->dp_port_lock, flags );
 885
 886         buf[0] = DIGI_CMD_TRANSMIT_IDLE;
 887         buf[1] = 0;
 888
 889         timeout += jiffies;
 890
 891         if( (ret=digi_write_inb_command( port, buf, 2, timeout-jiffies )) != 0 )
 892                 return( ret );
 893
 894         spin_lock_irqsave( &priv->dp_port_lock, flags );
 895
 896         while( time_before(jiffies, timeout) && !priv->dp_transmit_idle ) {
 897                 cond_wait_interruptible_timeout_irqrestore(
 898                         &priv->dp_transmit_idle_wait, DIGI_RETRY_TIMEOUT,
 899                         &priv->dp_port_lock, flags );
 900                 if( signal_pending(current) ) {
 901                         return( -EINTR );
 902                 }
 903                 spin_lock_irqsave( &priv->dp_port_lock, flags );
 904         }
 905
 906         priv->dp_transmit_idle = 0;
 907         spin_unlock_irqrestore( &priv->dp_port_lock, flags );
 908
 909         return( 0 );
 910
 911 }
 912
 913
 914 static void digi_rx_throttle( struct usb_serial_port *port )
 915 {
 916
 917         unsigned long flags;
 918         struct digi_port *priv = usb_get_serial_port_data(port);
 919
 920
 921 dbg( "digi_rx_throttle: TOP: port=%d", priv->dp_port_num );
 922
 923         /* stop receiving characters by not resubmitting the read urb */
 924         spin_lock_irqsave( &priv->dp_port_lock, flags );
 925         priv->dp_throttled = 1;
 926         priv->dp_throttle_restart = 0;
 927         priv->dp_in_buf_len = 0;
 928         spin_unlock_irqrestore( &priv->dp_port_lock, flags );
 929
 930 }
 931
 932
 933 static void digi_rx_unthrottle( struct usb_serial_port *port )
 934 {
 935
 936         int ret = 0;
 937         int len;
 938         unsigned long flags;
 939         struct digi_port *priv = usb_get_serial_port_data(port);
 940         struct tty_struct *tty = port->tty;
 941
 942
 943 dbg( "digi_rx_unthrottle: TOP: port=%d", priv->dp_port_num );
 944
 945         spin_lock_irqsave( &priv->dp_port_lock, flags );
 946
 947         /* send any buffered chars from throttle time on to tty subsystem */
 948
 949         len = tty_buffer_request_room(tty, priv->dp_in_buf_len);
 950         if( len > 0 ) {
 951                 tty_insert_flip_string_flags(tty, priv->dp_in_buf, priv->dp_in_flag_buf, len);
 952                 tty_flip_buffer_push( tty );
 953         }
 954
 955         /* restart read chain */
 956         if( priv->dp_throttle_restart ) {
 957                 port->read_urb->dev = port->serial->dev;
 958                 ret = usb_submit_urb( port->read_urb, GFP_ATOMIC );
 959         }
 960
 961         /* turn throttle off */
 962         priv->dp_throttled = 0;
 963         priv->dp_in_buf_len = 0;
 964         priv->dp_throttle_restart = 0;
 965
 966         spin_unlock_irqrestore( &priv->dp_port_lock, flags );
 967
 968         if( ret ) {
 969                 err("%s: usb_submit_urb failed, ret=%d, port=%d", __FUNCTION__,
 970                         ret, priv->dp_port_num );
 971         }
 972
 973 }
 974
 975
 976 static void digi_set_termios( struct usb_serial_port *port,
 977         struct termios *old_termios )
 978 {
 979
 980         struct digi_port *priv = usb_get_serial_port_data(port);
 981         unsigned int iflag = port->tty->termios->c_iflag;
 982         unsigned int cflag = port->tty->termios->c_cflag;
 983         unsigned int old_iflag = old_termios->c_iflag;
 984         unsigned int old_cflag = old_termios->c_cflag;
 985         unsigned char buf[32];
 986         unsigned int modem_signals;
 987         int arg,ret;
 988         int i = 0;
 989
 990
 991 dbg( "digi_set_termios: TOP: port=%d, iflag=0x%x, old_iflag=0x%x, cflag=0x%x, old_cflag=0x%x", priv->dp_port_num, iflag, old_iflag, cflag, old_cflag );
 992
 993         /* set baud rate */
 994         if( (cflag&CBAUD) != (old_cflag&CBAUD) ) {
 995
 996                 arg = -1;
 997
 998                 /* reassert DTR and (maybe) RTS on transition from B0 */
 999                 if( (old_cflag&CBAUD) == B0 ) {
1000                         /* don't set RTS if using hardware flow control */
1001                         /* and throttling input */
1002                         modem_signals = TIOCM_DTR;
1003                         if( !(port->tty->termios->c_cflag & CRTSCTS) ||
1004                         !test_bit(TTY_THROTTLED, &port->tty->flags) ) {
1005                                 modem_signals |= TIOCM_RTS;
1006                         }
1007                         digi_set_modem_signals( port, modem_signals, 1 );
1008                 }
1009
1010                 switch( (cflag&CBAUD) ) {
1011                         /* drop DTR and RTS on transition to B0 */
1012                 case B0: digi_set_modem_signals( port, 0, 1 ); break;
1013                 case B50: arg = DIGI_BAUD_50; break;
1014                 case B75: arg = DIGI_BAUD_75; break;
1015                 case B110: arg = DIGI_BAUD_110; break;
1016                 case B150: arg = DIGI_BAUD_150; break;
1017                 case B200: arg = DIGI_BAUD_200; break;
1018                 case B300: arg = DIGI_BAUD_300; break;
1019                 case B600: arg = DIGI_BAUD_600; break;
1020                 case B1200: arg = DIGI_BAUD_1200; break;
1021                 case B1800: arg = DIGI_BAUD_1800; break;
1022                 case B2400: arg = DIGI_BAUD_2400; break;
1023                 case B4800: arg = DIGI_BAUD_4800; break;
1024                 case B9600: arg = DIGI_BAUD_9600; break;
1025                 case B19200: arg = DIGI_BAUD_19200; break;
1026                 case B38400: arg = DIGI_BAUD_38400; break;
1027                 case B57600: arg = DIGI_BAUD_57600; break;
1028                 case B115200: arg = DIGI_BAUD_115200; break;
1029                 case B230400: arg = DIGI_BAUD_230400; break;
1030                 case B460800: arg = DIGI_BAUD_460800; break;
1031                 default:
1032                         dbg( "digi_set_termios: can't handle baud rate 0x%x",
1033                                 (cflag&CBAUD) );
1034                         break;
1035                 }
1036
1037                 if( arg != -1 ) {
1038                         buf[i++] = DIGI_CMD_SET_BAUD_RATE;
1039                         buf[i++] = priv->dp_port_num;
1040                         buf[i++] = arg;
1041                         buf[i++] = 0;
1042                 }
1043
1044         }
1045
1046         /* set parity */
1047         if( (cflag&(PARENB|PARODD)) != (old_cflag&(PARENB|PARODD)) ) {
1048
1049                 if( (cflag&PARENB) ) {
1050                         if( (cflag&PARODD) )
1051                                 arg = DIGI_PARITY_ODD;
1052                         else
1053                                 arg = DIGI_PARITY_EVEN;
1054                 } else {
1055                         arg = DIGI_PARITY_NONE;
1056                 }
1057
1058                 buf[i++] = DIGI_CMD_SET_PARITY;
1059                 buf[i++] = priv->dp_port_num;
1060                 buf[i++] = arg;
1061                 buf[i++] = 0;
1062
1063         }
1064
1065         /* set word size */
1066         if( (cflag&CSIZE) != (old_cflag&CSIZE) ) {
1067
1068                 arg = -1;
1069
1070                 switch( (cflag&CSIZE) ) {
1071                 case CS5: arg = DIGI_WORD_SIZE_5; break;
1072                 case CS6: arg = DIGI_WORD_SIZE_6; break;
1073                 case CS7: arg = DIGI_WORD_SIZE_7; break;
1074                 case CS8: arg = DIGI_WORD_SIZE_8; break;
1075                 default:
1076                         dbg( "digi_set_termios: can't handle word size %d",
1077                                 (cflag&CSIZE) );
1078                         break;
1079                 }
1080
1081                 if( arg != -1 ) {
1082                         buf[i++] = DIGI_CMD_SET_WORD_SIZE;
1083                         buf[i++] = priv->dp_port_num;
1084                         buf[i++] = arg;
1085                         buf[i++] = 0;
1086                 }
1087
1088         }
1089
1090         /* set stop bits */
1091         if( (cflag&CSTOPB) != (old_cflag&CSTOPB) ) {
1092
1093                 if( (cflag&CSTOPB) )
1094                         arg = DIGI_STOP_BITS_2;
1095                 else
1096                         arg = DIGI_STOP_BITS_1;
1097
1098                 buf[i++] = DIGI_CMD_SET_STOP_BITS;
1099                 buf[i++] = priv->dp_port_num;
1100                 buf[i++] = arg;
1101                 buf[i++] = 0;
1102
1103         }
1104
1105         /* set input flow control */
1106         if( (iflag&IXOFF) != (old_iflag&IXOFF)
1107         || (cflag&CRTSCTS) != (old_cflag&CRTSCTS) ) {
1108
1109                 arg = 0;
1110
1111                 if( (iflag&IXOFF) )
1112                         arg |= DIGI_INPUT_FLOW_CONTROL_XON_XOFF;
1113                 else
1114                         arg &= ~DIGI_INPUT_FLOW_CONTROL_XON_XOFF;
1115
1116                 if( (cflag&CRTSCTS) ) {
1117
1118                         arg |= DIGI_INPUT_FLOW_CONTROL_RTS;
1119
1120                         /* On USB-4 it is necessary to assert RTS prior */
1121                         /* to selecting RTS input flow control.  */
1122                         buf[i++] = DIGI_CMD_SET_RTS_SIGNAL;
1123                         buf[i++] = priv->dp_port_num;
1124                         buf[i++] = DIGI_RTS_ACTIVE;
1125                         buf[i++] = 0;
1126
1127                 } else {
1128                         arg &= ~DIGI_INPUT_FLOW_CONTROL_RTS;
1129                 }
1130
1131                 buf[i++] = DIGI_CMD_SET_INPUT_FLOW_CONTROL;
1132                 buf[i++] = priv->dp_port_num;
1133                 buf[i++] = arg;
1134                 buf[i++] = 0;
1135
1136         }
1137
1138         /* set output flow control */
1139         if( (iflag&IXON) != (old_iflag&IXON)
1140         || (cflag&CRTSCTS) != (old_cflag&CRTSCTS) ) {
1141
1142                 arg = 0;
1143
1144                 if( (iflag&IXON) )
1145                         arg |= DIGI_OUTPUT_FLOW_CONTROL_XON_XOFF;
1146                 else
1147                         arg &= ~DIGI_OUTPUT_FLOW_CONTROL_XON_XOFF;
1148
1149                 if( (cflag&CRTSCTS) ) {
1150                         arg |= DIGI_OUTPUT_FLOW_CONTROL_CTS;
1151                 } else {
1152                         arg &= ~DIGI_OUTPUT_FLOW_CONTROL_CTS;
1153                         port->tty->hw_stopped = 0;
1154                 }
1155
1156                 buf[i++] = DIGI_CMD_SET_OUTPUT_FLOW_CONTROL;
1157                 buf[i++] = priv->dp_port_num;
1158                 buf[i++] = arg;
1159                 buf[i++] = 0;
1160
1161         }
1162
1163         /* set receive enable/disable */
1164         if( (cflag&CREAD) != (old_cflag&CREAD) ) {
1165
1166                 if( (cflag&CREAD) )
1167                         arg = DIGI_ENABLE;
1168                 else
1169                         arg = DIGI_DISABLE;
1170
1171                 buf[i++] = DIGI_CMD_RECEIVE_ENABLE;
1172                 buf[i++] = priv->dp_port_num;
1173                 buf[i++] = arg;
1174                 buf[i++] = 0;
1175
1176         }
1177
1178         if( (ret=digi_write_oob_command( port, buf, i, 1 )) != 0 )
1179                 dbg( "digi_set_termios: write oob failed, ret=%d", ret );
1180
1181 }
1182
1183
1184 static void digi_break_ctl( struct usb_serial_port *port, int break_state )
1185 {
1186
1187         unsigned char buf[4];
1188
1189
1190         buf[0] = DIGI_CMD_BREAK_CONTROL;
1191         buf[1] = 2;                             /* length */
1192         buf[2] = break_state ? 1 : 0;
1193         buf[3] = 0;                             /* pad */
1194
1195         digi_write_inb_command( port, buf, 4, 0 );
1196
1197 }
1198
1199
1200 static int digi_tiocmget( struct usb_serial_port *port, struct file *file )
1201 {
1202         struct digi_port *priv = usb_get_serial_port_data(port);
1203         unsigned int val;
1204         unsigned long flags;
1205
1206         dbg("%s: TOP: port=%d", __FUNCTION__, priv->dp_port_num);
1207
1208         spin_lock_irqsave( &priv->dp_port_lock, flags );
1209         val = priv->dp_modem_signals;
1210         spin_unlock_irqrestore( &priv->dp_port_lock, flags );
1211         return val;
1212 }
1213
1214
1215 static int digi_tiocmset( struct usb_serial_port *port, struct file *file,
1216         unsigned int set, unsigned int clear )
1217 {
1218         struct digi_port *priv = usb_get_serial_port_data(port);
1219         unsigned int val;
1220         unsigned long flags;
1221
1222         dbg("%s: TOP: port=%d", __FUNCTION__, priv->dp_port_num);
1223
1224         spin_lock_irqsave( &priv->dp_port_lock, flags );
1225         val = (priv->dp_modem_signals & ~clear) | set;
1226         spin_unlock_irqrestore( &priv->dp_port_lock, flags );
1227         return digi_set_modem_signals( port, val, 1 );
1228 }
1229
1230
1231 static int digi_ioctl( struct usb_serial_port *port, struct file *file,
1232         unsigned int cmd, unsigned long arg )
1233 {
1234
1235         struct digi_port *priv = usb_get_serial_port_data(port);
1236
1237 dbg( "digi_ioctl: TOP: port=%d, cmd=0x%x", priv->dp_port_num, cmd );
1238
1239         switch (cmd) {
1240
1241         case TIOCMIWAIT:
1242                 /* wait for any of the 4 modem inputs (DCD,RI,DSR,CTS)*/
1243                 /* TODO */
1244                 return( 0 );
1245
1246         case TIOCGICOUNT:
1247                 /* return count of modemline transitions */
1248                 /* TODO */
1249                 return 0;
1250
1251         }
1252
1253         return( -ENOIOCTLCMD );
1254
1255 }
1256
1257
1258 static int digi_write( struct usb_serial_port *port, const unsigned char *buf, int count )
1259 {
1260
1261         int ret,data_len,new_len;
1262         struct digi_port *priv = usb_get_serial_port_data(port);
1263         unsigned char *data = port->write_urb->transfer_buffer;
1264         unsigned long flags = 0;
1265
1266
1267 dbg( "digi_write: TOP: port=%d, count=%d, in_interrupt=%ld",
1268 priv->dp_port_num, count, in_interrupt() );
1269
1270         /* copy user data (which can sleep) before getting spin lock */
1271         count = min( count, port->bulk_out_size-2 );
1272         count = min( 64, count);
1273
1274         /* be sure only one write proceeds at a time */
1275         /* there are races on the port private buffer */
1276         /* and races to check write_urb->status */
1277         spin_lock_irqsave( &priv->dp_port_lock, flags );
1278
1279         /* wait for urb status clear to submit another urb */
1280         if( port->write_urb->status == -EINPROGRESS
1281         || priv->dp_write_urb_in_use ) {
1282
1283                 /* buffer data if count is 1 (probably put_char) if possible */
1284                 if( count == 1 && priv->dp_out_buf_len < DIGI_OUT_BUF_SIZE ) {
1285                         priv->dp_out_buf[priv->dp_out_buf_len++] = *buf;
1286                         new_len = 1;
1287                 } else {
1288                         new_len = 0;
1289                 }
1290
1291                 spin_unlock_irqrestore( &priv->dp_port_lock, flags );
1292
1293                 return( new_len );
1294
1295         }
1296
1297         /* allow space for any buffered data and for new data, up to */
1298         /* transfer buffer size - 2 (for command and length bytes) */
1299         new_len = min(count, port->bulk_out_size-2-priv->dp_out_buf_len);
1300         data_len = new_len + priv->dp_out_buf_len;
1301
1302         if( data_len == 0 ) {
1303                 spin_unlock_irqrestore( &priv->dp_port_lock, flags );
1304                 return( 0 );
1305         }
1306
1307         port->write_urb->transfer_buffer_length = data_len+2;
1308         port->write_urb->dev = port->serial->dev;
1309
1310         *data++ = DIGI_CMD_SEND_DATA;
1311         *data++ = data_len;
1312
1313         /* copy in buffered data first */
1314         memcpy( data, priv->dp_out_buf, priv->dp_out_buf_len );
1315         data += priv->dp_out_buf_len;
1316
1317         /* copy in new data */
1318         memcpy( data, buf, new_len );
1319
1320         if( (ret=usb_submit_urb(port->write_urb, GFP_ATOMIC)) == 0 ) {
1321                 priv->dp_write_urb_in_use = 1;
1322                 ret = new_len;
1323                 priv->dp_out_buf_len = 0;
1324         }
1325
1326         /* return length of new data written, or error */
1327         spin_unlock_irqrestore( &priv->dp_port_lock, flags );
1328         if( ret < 0 ) {
1329                 err("%s: usb_submit_urb failed, ret=%d, port=%d", __FUNCTION__,
1330                         ret, priv->dp_port_num );
1331         }
1332
1333 dbg( "digi_write: returning %d", ret );
1334         return( ret );
1335
1336 }
1337
1338
1339 static void digi_write_bulk_callback( struct urb *urb )
1340 {
1341
1342         struct usb_serial_port *port = (struct usb_serial_port *)urb->context;
1343         struct usb_serial *serial;
1344         struct digi_port *priv;
1345         struct digi_serial *serial_priv;
1346         int ret = 0;
1347
1348
1349 dbg( "digi_write_bulk_callback: TOP, urb->status=%d", urb->status );
1350
1351         /* port and serial sanity check */
1352         if( port == NULL || (priv=usb_get_serial_port_data(port)) == NULL ) {
1353                 err("%s: port or port->private is NULL, status=%d", __FUNCTION__,
1354                         urb->status );
1355                 return;
1356         }
1357         serial = port->serial;
1358         if( serial == NULL || (serial_priv=usb_get_serial_data(serial)) == NULL ) {
1359                 err("%s: serial or serial->private is NULL, status=%d", __FUNCTION__, urb->status );
1360                 return;
1361         }
1362
1363         /* handle oob callback */
1364         if( priv->dp_port_num == serial_priv->ds_oob_port_num ) {
1365                 dbg( "digi_write_bulk_callback: oob callback" );
1366                 spin_lock( &priv->dp_port_lock );
1367                 priv->dp_write_urb_in_use = 0;
1368                 wake_up_interruptible( &port->write_wait );
1369                 spin_unlock( &priv->dp_port_lock );
1370                 return;
1371         }
1372
1373         /* try to send any buffered data on this port, if it is open */
1374         spin_lock( &priv->dp_port_lock );
1375         priv->dp_write_urb_in_use = 0;
1376         if( port->open_count && port->write_urb->status != -EINPROGRESS
1377         && priv->dp_out_buf_len > 0 ) {
1378
1379                 *((unsigned char *)(port->write_urb->transfer_buffer))
1380                         = (unsigned char)DIGI_CMD_SEND_DATA;
1381                 *((unsigned char *)(port->write_urb->transfer_buffer)+1)
1382                         = (unsigned char)priv->dp_out_buf_len;
1383
1384                 port->write_urb->transfer_buffer_length
1385                         = priv->dp_out_buf_len+2;
1386                 port->write_urb->dev = serial->dev;
1387
1388                 memcpy( port->write_urb->transfer_buffer+2, priv->dp_out_buf,
1389                         priv->dp_out_buf_len );
1390
1391                 if( (ret=usb_submit_urb(port->write_urb, GFP_ATOMIC)) == 0 ) {
1392                         priv->dp_write_urb_in_use = 1;
1393                         priv->dp_out_buf_len = 0;
1394                 }
1395
1396         }
1397
1398         /* wake up processes sleeping on writes immediately */
1399         digi_wakeup_write( port );
1400
1401         /* also queue up a wakeup at scheduler time, in case we */
1402         /* lost the race in write_chan(). */
1403         schedule_work(&priv->dp_wakeup_work);
1404
1405         spin_unlock( &priv->dp_port_lock );
1406
1407         if( ret ) {
1408                 err("%s: usb_submit_urb failed, ret=%d, port=%d", __FUNCTION__,
1409                         ret, priv->dp_port_num );
1410         }
1411
1412 }
1413
1414
1415 static int digi_write_room( struct usb_serial_port *port )
1416 {
1417
1418         int room;
1419         struct digi_port *priv = usb_get_serial_port_data(port);
1420         unsigned long flags = 0;
1421
1422
1423         spin_lock_irqsave( &priv->dp_port_lock, flags );
1424
1425         if( port->write_urb->status == -EINPROGRESS
1426         || priv->dp_write_urb_in_use )
1427                 room = 0;
1428         else
1429                 room = port->bulk_out_size - 2 - priv->dp_out_buf_len;
1430
1431         spin_unlock_irqrestore( &priv->dp_port_lock, flags );
1432
1433 dbg( "digi_write_room: port=%d, room=%d", priv->dp_port_num, room );
1434         return( room );
1435
1436 }
1437
1438
1439 static int digi_chars_in_buffer( struct usb_serial_port *port )
1440 {
1441
1442         struct digi_port *priv = usb_get_serial_port_data(port);
1443
1444
1445         if( port->write_urb->status == -EINPROGRESS
1446         || priv->dp_write_urb_in_use ) {
1447 dbg( "digi_chars_in_buffer: port=%d, chars=%d", priv->dp_port_num, port->bulk_out_size - 2 );
1448                 /* return( port->bulk_out_size - 2 ); */
1449                 return( 256 );
1450         } else {
1451 dbg( "digi_chars_in_buffer: port=%d, chars=%d", priv->dp_port_num, priv->dp_out_buf_len );
1452                 return( priv->dp_out_buf_len );
1453         }
1454
1455 }
1456
1457
1458 static int digi_open( struct usb_serial_port *port, struct file *filp )
1459 {
1460
1461         int ret;
1462         unsigned char buf[32];
1463         struct digi_port *priv = usb_get_serial_port_data(port);
1464         struct termios not_termios;
1465         unsigned long flags = 0;
1466
1467
1468 dbg( "digi_open: TOP: port=%d, open_count=%d", priv->dp_port_num, port->open_count );
1469
1470         /* be sure the device is started up */
1471         if( digi_startup_device( port->serial ) != 0 )
1472                 return( -ENXIO );
1473
1474         spin_lock_irqsave( &priv->dp_port_lock, flags );
1475
1476         /* don't wait on a close in progress for non-blocking opens */
1477         if( priv->dp_in_close && (filp->f_flags&(O_NDELAY|O_NONBLOCK)) == 0 ) {
1478                 spin_unlock_irqrestore( &priv->dp_port_lock, flags );
1479                 return( -EAGAIN );
1480         }
1481
1482         /* wait for a close in progress to finish */
1483         while( priv->dp_in_close ) {
1484                 cond_wait_interruptible_timeout_irqrestore(
1485                         &priv->dp_close_wait, DIGI_RETRY_TIMEOUT,
1486                         &priv->dp_port_lock, flags );
1487                 if( signal_pending(current) ) {
1488                         return( -EINTR );
1489                 }
1490                 spin_lock_irqsave( &priv->dp_port_lock, flags );
1491         }
1492
1493         spin_unlock_irqrestore( &priv->dp_port_lock, flags );
1494
1495         /* read modem signals automatically whenever they change */
1496         buf[0] = DIGI_CMD_READ_INPUT_SIGNALS;
1497         buf[1] = priv->dp_port_num;
1498         buf[2] = DIGI_ENABLE;
1499         buf[3] = 0;
1500
1501         /* flush fifos */
1502         buf[4] = DIGI_CMD_IFLUSH_FIFO;
1503         buf[5] = priv->dp_port_num;
1504         buf[6] = DIGI_FLUSH_TX | DIGI_FLUSH_RX;
1505         buf[7] = 0;
1506
1507         if( (ret=digi_write_oob_command( port, buf, 8, 1 )) != 0 )
1508                 dbg( "digi_open: write oob failed, ret=%d", ret );
1509
1510         /* set termios settings */
1511         not_termios.c_cflag = ~port->tty->termios->c_cflag;
1512         not_termios.c_iflag = ~port->tty->termios->c_iflag;
1513         digi_set_termios( port, &not_termios );
1514
1515         /* set DTR and RTS */
1516         digi_set_modem_signals( port, TIOCM_DTR|TIOCM_RTS, 1 );
1517
1518         return( 0 );
1519
1520 }
1521
1522
1523 static void digi_close( struct usb_serial_port *port, struct file *filp )
1524 {
1525         DEFINE_WAIT(wait);
1526         int ret;
1527         unsigned char buf[32];
1528         struct tty_struct *tty = port->tty;
1529         struct digi_port *priv = usb_get_serial_port_data(port);
1530         unsigned long flags = 0;
1531
1532
1533 dbg( "digi_close: TOP: port=%d, open_count=%d", priv->dp_port_num, port->open_count );
1534
1535
1536         /* if disconnected, just clear flags */
1537         if (!usb_get_intfdata(port->serial->interface))
1538                 goto exit;
1539
1540         /* do cleanup only after final close on this port */
1541         spin_lock_irqsave( &priv->dp_port_lock, flags );
1542         priv->dp_in_close = 1;
1543         spin_unlock_irqrestore( &priv->dp_port_lock, flags );
1544
1545         /* tell line discipline to process only XON/XOFF */
1546         tty->closing = 1;
1547
1548         /* wait for output to drain */
1549         if( (filp->f_flags&(O_NDELAY|O_NONBLOCK)) == 0 ) {
1550                 tty_wait_until_sent( tty, DIGI_CLOSE_TIMEOUT );
1551         }
1552
1553         /* flush driver and line discipline buffers */
1554         if( tty->driver->flush_buffer )
1555                 tty->driver->flush_buffer( tty );
1556         tty_ldisc_flush(tty);
1557
1558         if (port->serial->dev) {
1559                 /* wait for transmit idle */
1560                 if( (filp->f_flags&(O_NDELAY|O_NONBLOCK)) == 0 ) {
1561                         digi_transmit_idle( port, DIGI_CLOSE_TIMEOUT );
1562                 }
1563
1564                 /* drop DTR and RTS */
1565                 digi_set_modem_signals( port, 0, 0 );
1566
1567                 /* disable input flow control */
1568                 buf[0] = DIGI_CMD_SET_INPUT_FLOW_CONTROL;
1569                 buf[1] = priv->dp_port_num;
1570                 buf[2] = DIGI_DISABLE;
1571                 buf[3] = 0;
1572
1573                 /* disable output flow control */
1574                 buf[4] = DIGI_CMD_SET_OUTPUT_FLOW_CONTROL;
1575                 buf[5] = priv->dp_port_num;
1576                 buf[6] = DIGI_DISABLE;
1577                 buf[7] = 0;
1578
1579                 /* disable reading modem signals automatically */
1580                 buf[8] = DIGI_CMD_READ_INPUT_SIGNALS;
1581                 buf[9] = priv->dp_port_num;
1582                 buf[10] = DIGI_DISABLE;
1583                 buf[11] = 0;
1584
1585                 /* disable receive */
1586                 buf[12] = DIGI_CMD_RECEIVE_ENABLE;
1587                 buf[13] = priv->dp_port_num;
1588                 buf[14] = DIGI_DISABLE;
1589                 buf[15] = 0;
1590
1591                 /* flush fifos */
1592                 buf[16] = DIGI_CMD_IFLUSH_FIFO;
1593                 buf[17] = priv->dp_port_num;
1594                 buf[18] = DIGI_FLUSH_TX | DIGI_FLUSH_RX;
1595                 buf[19] = 0;
1596
1597                 if( (ret=digi_write_oob_command( port, buf, 20, 0 )) != 0 )
1598                         dbg( "digi_close: write oob failed, ret=%d", ret );
1599
1600                 /* wait for final commands on oob port to complete */
1601                 prepare_to_wait(&priv->dp_flush_wait, &wait, TASK_INTERRUPTIBLE);
1602                 schedule_timeout(DIGI_CLOSE_TIMEOUT);
1603                 finish_wait(&priv->dp_flush_wait, &wait);
1604
1605                 /* shutdown any outstanding bulk writes */
1606                 usb_kill_urb(port->write_urb);
1607         }
1608
1609         tty->closing = 0;
1610
1611 exit:
1612         spin_lock_irqsave( &priv->dp_port_lock, flags );
1613         priv->dp_write_urb_in_use = 0;
1614         priv->dp_in_close = 0;
1615         wake_up_interruptible( &priv->dp_close_wait );
1616         spin_unlock_irqrestore( &priv->dp_port_lock, flags );
1617
1618 dbg( "digi_close: done" );
1619 }
1620
1621
1622 /*
1623 *  Digi Startup Device
1624 *
1625 *  Starts reads on all ports.  Must be called AFTER startup, with
1626 *  urbs initialized.  Returns 0 if successful, non-zero error otherwise.
1627 */
1628
1629 static int digi_startup_device( struct usb_serial *serial )
1630 {
1631
1632         int i,ret = 0;
1633         struct digi_serial *serial_priv = usb_get_serial_data(serial);
1634         struct usb_serial_port *port;
1635
1636
1637         /* be sure this happens exactly once */
1638         spin_lock( &serial_priv->ds_serial_lock );
1639         if( serial_priv->ds_device_started ) {
1640                 spin_unlock( &serial_priv->ds_serial_lock );
1641                 return( 0 );
1642         }
1643         serial_priv->ds_device_started = 1;
1644         spin_unlock( &serial_priv->ds_serial_lock );
1645
1646         /* start reading from each bulk in endpoint for the device */
1647         /* set USB_DISABLE_SPD flag for write bulk urbs */
1648         for( i=0; i<serial->type->num_ports+1; i++ ) {
1649
1650                 port = serial->port[i];
1651
1652                 port->write_urb->dev = port->serial->dev;
1653
1654                 if( (ret=usb_submit_urb(port->read_urb, GFP_KERNEL)) != 0 ) {
1655                         err("%s: usb_submit_urb failed, ret=%d, port=%d", __FUNCTION__,
1656                         ret, i );
1657                         break;
1658                 }
1659
1660         }
1661
1662         return( ret );
1663
1664 }
1665
1666
1667 static int digi_startup( struct usb_serial *serial )
1668 {
1669
1670         int i;
1671         struct digi_port *priv;
1672         struct digi_serial *serial_priv;
1673
1674
1675 dbg( "digi_startup: TOP" );
1676
1677         /* allocate the private data structures for all ports */
1678         /* number of regular ports + 1 for the out-of-band port */
1679         for( i=0; i<serial->type->num_ports+1; i++ ) {
1680
1681                 /* allocate port private structure */
1682                 priv = (struct digi_port *)kmalloc( sizeof(struct digi_port),
1683                         GFP_KERNEL );
1684                 if( priv == (struct digi_port *)0 ) {
1685                         while( --i >= 0 )
1686                                 kfree( usb_get_serial_port_data(serial->port[i]) );
1687                         return( 1 );                    /* error */
1688                 }
1689
1690                 /* initialize port private structure */
1691                 spin_lock_init( &priv->dp_port_lock );
1692                 priv->dp_port_num = i;
1693                 priv->dp_out_buf_len = 0;
1694                 priv->dp_in_buf_len = 0;
1695                 priv->dp_write_urb_in_use = 0;
1696                 priv->dp_modem_signals = 0;
1697                 init_waitqueue_head( &priv->dp_modem_change_wait );
1698                 priv->dp_transmit_idle = 0;
1699                 init_waitqueue_head( &priv->dp_transmit_idle_wait );
1700                 priv->dp_throttled = 0;
1701                 priv->dp_throttle_restart = 0;
1702                 init_waitqueue_head( &priv->dp_flush_wait );
1703                 priv->dp_in_close = 0;
1704                 init_waitqueue_head( &priv->dp_close_wait );
1705                 INIT_WORK(&priv->dp_wakeup_work,
1706                                 digi_wakeup_write_lock, serial->port[i]);
1707
1708                 /* initialize write wait queue for this port */
1709                 init_waitqueue_head( &serial->port[i]->write_wait );
1710
1711                 usb_set_serial_port_data(serial->port[i], priv);
1712         }
1713
1714         /* allocate serial private structure */
1715         serial_priv = (struct digi_serial *)kmalloc( sizeof(struct digi_serial),
1716                 GFP_KERNEL );
1717         if( serial_priv == (struct digi_serial *)0 ) {
1718                 for( i=0; i<serial->type->num_ports+1; i++ )
1719                         kfree( usb_get_serial_port_data(serial->port[i]) );
1720                 return( 1 );                    /* error */
1721         }
1722
1723         /* initialize serial private structure */
1724         spin_lock_init( &serial_priv->ds_serial_lock );
1725         serial_priv->ds_oob_port_num = serial->type->num_ports;
1726         serial_priv->ds_oob_port = serial->port[serial_priv->ds_oob_port_num];
1727         serial_priv->ds_device_started = 0;
1728         usb_set_serial_data(serial, serial_priv);
1729
1730         return( 0 );
1731
1732 }
1733
1734
1735 static void digi_shutdown( struct usb_serial *serial )
1736 {
1737
1738         int i;
1739
1740
1741 dbg( "digi_shutdown: TOP, in_interrupt()=%ld", in_interrupt() );
1742
1743         /* stop reads and writes on all ports */
1744         for( i=0; i<serial->type->num_ports+1; i++ ) {
1745                 usb_kill_urb(serial->port[i]->read_urb);
1746                 usb_kill_urb(serial->port[i]->write_urb);
1747         }
1748
1749         /* free the private data structures for all ports */
1750         /* number of regular ports + 1 for the out-of-band port */
1751         for( i=0; i<serial->type->num_ports+1; i++ )
1752                 kfree( usb_get_serial_port_data(serial->port[i]) );
1753         kfree( usb_get_serial_data(serial) );
1754 }
1755
1756
1757 static void digi_read_bulk_callback( struct urb *urb )
1758 {
1759
1760         struct usb_serial_port *port = (struct usb_serial_port *)urb->context;
1761         struct digi_port *priv;
1762         struct digi_serial *serial_priv;
1763         int ret;
1764
1765
1766 dbg( "digi_read_bulk_callback: TOP" );
1767
1768         /* port sanity check, do not resubmit if port is not valid */
1769         if( port == NULL || (priv=usb_get_serial_port_data(port)) == NULL ) {
1770                 err("%s: port or port->private is NULL, status=%d", __FUNCTION__,
1771                         urb->status );
1772                 return;
1773         }
1774         if( port->serial == NULL
1775         || (serial_priv=usb_get_serial_data(port->serial)) == NULL ) {
1776                 err("%s: serial is bad or serial->private is NULL, status=%d", __FUNCTION__, urb->status );
1777                 return;
1778         }
1779
1780         /* do not resubmit urb if it has any status error */
1781         if( urb->status ) {
1782                 err("%s: nonzero read bulk status: status=%d, port=%d", __FUNCTION__, urb->status, priv->dp_port_num );
1783                 return;
1784         }
1785
1786         /* handle oob or inb callback, do not resubmit if error */
1787         if( priv->dp_port_num == serial_priv->ds_oob_port_num ) {
1788                 if( digi_read_oob_callback( urb ) != 0 )
1789                         return;
1790         } else {
1791                 if( digi_read_inb_callback( urb ) != 0 )
1792                         return;
1793         }
1794
1795         /* continue read */
1796         urb->dev = port->serial->dev;
1797         if( (ret=usb_submit_urb(urb, GFP_ATOMIC)) != 0 ) {
1798                 err("%s: failed resubmitting urb, ret=%d, port=%d", __FUNCTION__,
1799                         ret, priv->dp_port_num );
1800         }
1801
1802 }
1803
1804
1805 /*
1806 *  Digi Read INB Callback
1807 *
1808 *  Digi Read INB Callback handles reads on the in band ports, sending
1809 *  the data on to the tty subsystem.  When called we know port and
1810 *  port->private are not NULL and port->serial has been validated.
1811 *  It returns 0 if successful, 1 if successful but the port is
1812 *  throttled, and -1 if the sanity checks failed.
1813 */
1814
1815 static int digi_read_inb_callback( struct urb *urb )
1816 {
1817
1818         struct usb_serial_port *port = (struct usb_serial_port *)urb->context;
1819         struct tty_struct *tty = port->tty;
1820         struct digi_port *priv = usb_get_serial_port_data(port);
1821         int opcode = ((unsigned char *)urb->transfer_buffer)[0];
1822         int len = ((unsigned char *)urb->transfer_buffer)[1];
1823         int status = ((unsigned char *)urb->transfer_buffer)[2];
1824         unsigned char *data = ((unsigned char *)urb->transfer_buffer)+3;
1825         int flag,throttled;
1826         int i;
1827
1828         /* do not process callbacks on closed ports */
1829         /* but do continue the read chain */
1830         if( port->open_count == 0 )
1831                 return( 0 );
1832
1833         /* short/multiple packet check */
1834         if( urb->actual_length != len + 2 ) {
1835                 err("%s: INCOMPLETE OR MULTIPLE PACKET, urb->status=%d, port=%d, opcode=%d, len=%d, actual_length=%d, status=%d", __FUNCTION__, urb->status, priv->dp_port_num, opcode, len, urb->actual_length, status );
1836                 return( -1 );
1837         }
1838
1839         spin_lock( &priv->dp_port_lock );
1840
1841         /* check for throttle; if set, do not resubmit read urb */
1842         /* indicate the read chain needs to be restarted on unthrottle */
1843         throttled = priv->dp_throttled;
1844         if( throttled )
1845                 priv->dp_throttle_restart = 1;
1846
1847         /* receive data */
1848         if( opcode == DIGI_CMD_RECEIVE_DATA ) {
1849
1850                 /* get flag from status */
1851                 flag = 0;
1852
1853                 /* overrun is special, not associated with a char */
1854                 if( status & DIGI_OVERRUN_ERROR ) {
1855                         tty_insert_flip_char( tty, 0, TTY_OVERRUN );
1856                 }
1857
1858                 /* break takes precedence over parity, */
1859                 /* which takes precedence over framing errors */
1860                 if( status & DIGI_BREAK_ERROR ) {
1861                         flag = TTY_BREAK;
1862                 } else if( status & DIGI_PARITY_ERROR ) {
1863                         flag = TTY_PARITY;
1864                 } else if( status & DIGI_FRAMING_ERROR ) {
1865                         flag = TTY_FRAME;
1866                 }
1867
1868                 /* data length is len-1 (one byte of len is status) */
1869                 --len;
1870
1871                 if( throttled ) {
1872
1873                         len = min( len,
1874                                 DIGI_IN_BUF_SIZE - priv->dp_in_buf_len );
1875
1876                         if( len > 0 ) {
1877                                 memcpy( priv->dp_in_buf + priv->dp_in_buf_len,
1878                                         data, len );
1879                                 memset( priv->dp_in_flag_buf
1880                                         + priv->dp_in_buf_len, flag, len );
1881                                 priv->dp_in_buf_len += len;
1882                         }
1883
1884                 } else {
1885                         len = tty_buffer_request_room(tty, len);
1886                         if( len > 0 ) {
1887                                 /* Hot path */
1888                                 if(flag == TTY_NORMAL)
1889                                         tty_insert_flip_string(tty, data, len);
1890                                 else {
1891                                         for(i = 0; i < len; i++)
1892                                                 tty_insert_flip_char(tty, data[i], flag);
1893                                 }
1894                                 tty_flip_buffer_push( tty );
1895                         }
1896                 }
1897         }
1898
1899         spin_unlock( &priv->dp_port_lock );
1900
1901         if( opcode == DIGI_CMD_RECEIVE_DISABLE ) {
1902                 dbg("%s: got RECEIVE_DISABLE", __FUNCTION__ );
1903         } else if( opcode != DIGI_CMD_RECEIVE_DATA ) {
1904                 dbg("%s: unknown opcode: %d", __FUNCTION__, opcode );
1905         }
1906
1907         return( throttled ? 1 : 0 );
1908
1909 }
1910
1911
1912 /*
1913 *  Digi Read OOB Callback
1914 *
1915 *  Digi Read OOB Callback handles reads on the out of band port.
1916 *  When called we know port and port->private are not NULL and
1917 *  the port->serial is valid.  It returns 0 if successful, and
1918 *  -1 if the sanity checks failed.
1919 */
1920
1921 static int digi_read_oob_callback( struct urb *urb )
1922 {
1923
1924         struct usb_serial_port *port = (struct usb_serial_port *)urb->context;
1925         struct usb_serial *serial = port->serial;
1926         struct digi_port *priv = usb_get_serial_port_data(port);
1927         int opcode, line, status, val;
1928         int i;
1929
1930
1931 dbg( "digi_read_oob_callback: port=%d, len=%d", priv->dp_port_num,
1932 urb->actual_length );
1933
1934         /* handle each oob command */
1935         for( i=0; i<urb->actual_length-3; ) {
1936
1937                 opcode = ((unsigned char *)urb->transfer_buffer)[i++];
1938                 line = ((unsigned char *)urb->transfer_buffer)[i++];
1939                 status = ((unsigned char *)urb->transfer_buffer)[i++];
1940                 val = ((unsigned char *)urb->transfer_buffer)[i++];
1941
1942 dbg( "digi_read_oob_callback: opcode=%d, line=%d, status=%d, val=%d",
1943 opcode, line, status, val );
1944
1945                 if( status != 0 || line >= serial->type->num_ports )
1946                         continue;
1947
1948                 port = serial->port[line];
1949
1950                 if ((priv=usb_get_serial_port_data(port)) == NULL )
1951                         return -1;
1952
1953                 if( opcode == DIGI_CMD_READ_INPUT_SIGNALS ) {
1954
1955                         spin_lock( &priv->dp_port_lock );
1956
1957                         /* convert from digi flags to termiox flags */
1958                         if( val & DIGI_READ_INPUT_SIGNALS_CTS ) {
1959                                 priv->dp_modem_signals |= TIOCM_CTS;
1960                                 /* port must be open to use tty struct */
1961                                 if( port->open_count
1962                                 && port->tty->termios->c_cflag & CRTSCTS ) {
1963                                         port->tty->hw_stopped = 0;
1964                                         digi_wakeup_write( port );
1965                                 }
1966                         } else {
1967                                 priv->dp_modem_signals &= ~TIOCM_CTS;
1968                                 /* port must be open to use tty struct */
1969                                 if( port->open_count
1970                                 && port->tty->termios->c_cflag & CRTSCTS ) {
1971                                         port->tty->hw_stopped = 1;
1972                                 }
1973                         }
1974                         if( val & DIGI_READ_INPUT_SIGNALS_DSR )
1975                                 priv->dp_modem_signals |= TIOCM_DSR;
1976                         else
1977                                 priv->dp_modem_signals &= ~TIOCM_DSR;
1978                         if( val & DIGI_READ_INPUT_SIGNALS_RI )
1979                                 priv->dp_modem_signals |= TIOCM_RI;
1980                         else
1981                                 priv->dp_modem_signals &= ~TIOCM_RI;
1982                         if( val & DIGI_READ_INPUT_SIGNALS_DCD )
1983                                 priv->dp_modem_signals |= TIOCM_CD;
1984                         else
1985                                 priv->dp_modem_signals &= ~TIOCM_CD;
1986
1987                         wake_up_interruptible( &priv->dp_modem_change_wait );
1988                         spin_unlock( &priv->dp_port_lock );
1989
1990                 } else if( opcode == DIGI_CMD_TRANSMIT_IDLE ) {
1991
1992                         spin_lock( &priv->dp_port_lock );
1993                         priv->dp_transmit_idle = 1;
1994                         wake_up_interruptible( &priv->dp_transmit_idle_wait );
1995                         spin_unlock( &priv->dp_port_lock );
1996
1997                 } else if( opcode == DIGI_CMD_IFLUSH_FIFO ) {
1998
1999                         wake_up_interruptible( &priv->dp_flush_wait );
2000
2001                 }
2002
2003         }
2004
2005         return( 0 );
2006
2007 }
2008
2009
2010 static int __init digi_init (void)
2011 {
2012         int retval;
2013         retval = usb_serial_register(&digi_acceleport_2_device);
2014         if (retval)
2015                 goto failed_acceleport_2_device;
2016         retval = usb_serial_register(&digi_acceleport_4_device);
2017         if (retval)
2018                 goto failed_acceleport_4_device;
2019         retval = usb_register(&digi_driver);
2020         if (retval)
2021                 goto failed_usb_register;
2022         info(DRIVER_VERSION ":" DRIVER_DESC);
2023         return 0;
2024 failed_usb_register:
2025         usb_serial_deregister(&digi_acceleport_4_device);
2026 failed_acceleport_4_device:
2027         usb_serial_deregister(&digi_acceleport_2_device);
2028 failed_acceleport_2_device:
2029         return retval;
2030 }
2031
2032
2033 static void __exit digi_exit (void)
2034 {
2035         usb_deregister (&digi_driver);
2036         usb_serial_deregister (&digi_acceleport_2_device);
2037         usb_serial_deregister (&digi_acceleport_4_device);
2038 }
2039
2040
2041 module_init(digi_init);
2042 module_exit(digi_exit);
2043
2044
2045 MODULE_AUTHOR( DRIVER_AUTHOR );
2046 MODULE_DESCRIPTION( DRIVER_DESC );
2047 MODULE_LICENSE("GPL");
2048
2049 module_param(debug, bool, S_IRUGO | S_IWUSR);
2050 MODULE_PARM_DESC(debug, "Debug enabled or not");