drivers/usb/dwc3/core.c

   1 // SPDX-License-Identifier: GPL-2.0
   2 /**
   3  * core.c - DesignWare USB3 DRD Controller Core file
   4  *
   5  * Copyright (C) 2010-2011 Texas Instruments Incorporated - http://www.ti.com
   6  *
   7  * Authors: Felipe Balbi <balbi@ti.com>,
   8  *          Sebastian Andrzej Siewior <bigeasy@linutronix.de>
   9  */
  10
  11 #include <linux/clk.h>
  12 #include <linux/version.h>
  13 #include <linux/module.h>
  14 #include <linux/kernel.h>
  15 #include <linux/slab.h>
  16 #include <linux/spinlock.h>
  17 #include <linux/platform_device.h>
  18 #include <linux/pm_runtime.h>
  19 #include <linux/interrupt.h>
  20 #include <linux/ioport.h>
  21 #include <linux/io.h>
  22 #include <linux/list.h>
  23 #include <linux/delay.h>
  24 #include <linux/dma-mapping.h>
  25 #include <linux/of.h>
  26 #include <linux/acpi.h>
  27 #include <linux/pinctrl/consumer.h>
  28 #include <linux/reset.h>
  29
  30 #include <linux/usb/ch9.h>
  31 #include <linux/usb/gadget.h>
  32 #include <linux/usb/of.h>
  33 #include <linux/usb/otg.h>
  34
  35 #include "core.h"
  36 #include "gadget.h"
  37 #include "io.h"
  38
  39 #include "debug.h"
  40
  41 #define DWC3_DEFAULT_AUTOSUSPEND_DELAY  5000 /* ms */
  42
  43 /**
  44  * dwc3_get_dr_mode - Validates and sets dr_mode
  45  * @dwc: pointer to our context structure
  46  */
  47 static int dwc3_get_dr_mode(struct dwc3 *dwc)
  48 {
  49         enum usb_dr_mode mode;
  50         struct device *dev = dwc->dev;
  51         unsigned int hw_mode;
  52
  53         if (dwc->dr_mode == USB_DR_MODE_UNKNOWN)
  54                 dwc->dr_mode = USB_DR_MODE_OTG;
  55
  56         mode = dwc->dr_mode;
  57         hw_mode = DWC3_GHWPARAMS0_MODE(dwc->hwparams.hwparams0);
  58
  59         switch (hw_mode) {
  60         case DWC3_GHWPARAMS0_MODE_GADGET:
  61                 if (IS_ENABLED(CONFIG_USB_DWC3_HOST)) {
  62                         dev_err(dev,
  63                                 "Controller does not support host mode.\n");
  64                         return -EINVAL;
  65                 }
  66                 mode = USB_DR_MODE_PERIPHERAL;
  67                 break;
  68         case DWC3_GHWPARAMS0_MODE_HOST:
  69                 if (IS_ENABLED(CONFIG_USB_DWC3_GADGET)) {
  70                         dev_err(dev,
  71                                 "Controller does not support device mode.\n");
  72                         return -EINVAL;
  73                 }
  74                 mode = USB_DR_MODE_HOST;
  75                 break;
  76         default:
  77                 if (IS_ENABLED(CONFIG_USB_DWC3_HOST))
  78                         mode = USB_DR_MODE_HOST;
  79                 else if (IS_ENABLED(CONFIG_USB_DWC3_GADGET))
  80                         mode = USB_DR_MODE_PERIPHERAL;
  81
  82                 /*
  83                  * dwc_usb31 does not support OTG mode. If the controller
  84                  * supports DRD but the dr_mode is not specified or set to OTG,
  85                  * then set the mode to peripheral.
  86                  */
  87                 if (mode == USB_DR_MODE_OTG && dwc3_is_usb31(dwc))
  88                         mode = USB_DR_MODE_PERIPHERAL;
  89         }
  90
  91         if (mode != dwc->dr_mode) {
  92                 dev_warn(dev,
  93                          "Configuration mismatch. dr_mode forced to %s\n",
  94                          mode == USB_DR_MODE_HOST ? "host" : "gadget");
  95
  96                 dwc->dr_mode = mode;
  97         }
  98
  99         return 0;
 100 }
 101
 102 void dwc3_set_prtcap(struct dwc3 *dwc, u32 mode)
 103 {
 104         u32 reg;
 105
 106         reg = dwc3_readl(dwc->regs, DWC3_GCTL);
 107         reg &= ~(DWC3_GCTL_PRTCAPDIR(DWC3_GCTL_PRTCAP_OTG));
 108         reg |= DWC3_GCTL_PRTCAPDIR(mode);
 109         dwc3_writel(dwc->regs, DWC3_GCTL, reg);
 110
 111         dwc->current_dr_role = mode;
 112 }
 113
 114 static void __dwc3_set_mode(struct work_struct *work)
 115 {
 116         struct dwc3 *dwc = work_to_dwc(work);
 117         unsigned long flags;
 118         int ret;
 119
 120         if (dwc->dr_mode != USB_DR_MODE_OTG)
 121                 return;
 122
 123         if (dwc->current_dr_role == DWC3_GCTL_PRTCAP_OTG)
 124                 dwc3_otg_update(dwc, 0);
 125
 126         if (!dwc->desired_dr_role)
 127                 return;
 128
 129         if (dwc->desired_dr_role == dwc->current_dr_role)
 130                 return;
 131
 132         if (dwc->desired_dr_role == DWC3_GCTL_PRTCAP_OTG && dwc->edev)
 133                 return;
 134
 135         switch (dwc->current_dr_role) {
 136         case DWC3_GCTL_PRTCAP_HOST:
 137                 dwc3_host_exit(dwc);
 138                 break;
 139         case DWC3_GCTL_PRTCAP_DEVICE:
 140                 dwc3_gadget_exit(dwc);
 141                 dwc3_event_buffers_cleanup(dwc);
 142                 break;
 143         case DWC3_GCTL_PRTCAP_OTG:
 144                 dwc3_otg_exit(dwc);
 145                 spin_lock_irqsave(&dwc->lock, flags);
 146                 dwc->desired_otg_role = DWC3_OTG_ROLE_IDLE;
 147                 spin_unlock_irqrestore(&dwc->lock, flags);
 148                 dwc3_otg_update(dwc, 1);
 149                 break;
 150         default:
 151                 break;
 152         }
 153
 154         spin_lock_irqsave(&dwc->lock, flags);
 155
 156         dwc3_set_prtcap(dwc, dwc->desired_dr_role);
 157
 158         spin_unlock_irqrestore(&dwc->lock, flags);
 159
 160         switch (dwc->desired_dr_role) {
 161         case DWC3_GCTL_PRTCAP_HOST:
 162                 ret = dwc3_host_init(dwc);
 163                 if (ret) {
 164                         dev_err(dwc->dev, "failed to initialize host\n");
 165                 } else {
 166                         if (dwc->usb2_phy)
 167                                 otg_set_vbus(dwc->usb2_phy->otg, true);
 168                         phy_set_mode(dwc->usb2_generic_phy, PHY_MODE_USB_HOST);
 169                         phy_set_mode(dwc->usb3_generic_phy, PHY_MODE_USB_HOST);
 170                         phy_calibrate(dwc->usb2_generic_phy);
 171                 }
 172                 break;
 173         case DWC3_GCTL_PRTCAP_DEVICE:
 174                 dwc3_event_buffers_setup(dwc);
 175
 176                 if (dwc->usb2_phy)
 177                         otg_set_vbus(dwc->usb2_phy->otg, false);
 178                 phy_set_mode(dwc->usb2_generic_phy, PHY_MODE_USB_DEVICE);
 179                 phy_set_mode(dwc->usb3_generic_phy, PHY_MODE_USB_DEVICE);
 180
 181                 ret = dwc3_gadget_init(dwc);
 182                 if (ret)
 183                         dev_err(dwc->dev, "failed to initialize peripheral\n");
 184                 break;
 185         case DWC3_GCTL_PRTCAP_OTG:
 186                 dwc3_otg_init(dwc);
 187                 dwc3_otg_update(dwc, 0);
 188                 break;
 189         default:
 190                 break;
 191         }
 192
 193 }
 194
 195 void dwc3_set_mode(struct dwc3 *dwc, u32 mode)
 196 {
 197         unsigned long flags;
 198
 199         spin_lock_irqsave(&dwc->lock, flags);
 200         dwc->desired_dr_role = mode;
 201         spin_unlock_irqrestore(&dwc->lock, flags);
 202
 203         queue_work(system_freezable_wq, &dwc->drd_work);
 204 }
 205
 206 u32 dwc3_core_fifo_space(struct dwc3_ep *dep, u8 type)
 207 {
 208         struct dwc3             *dwc = dep->dwc;
 209         u32                     reg;
 210
 211         dwc3_writel(dwc->regs, DWC3_GDBGFIFOSPACE,
 212                         DWC3_GDBGFIFOSPACE_NUM(dep->number) |
 213                         DWC3_GDBGFIFOSPACE_TYPE(type));
 214
 215         reg = dwc3_readl(dwc->regs, DWC3_GDBGFIFOSPACE);
 216
 217         return DWC3_GDBGFIFOSPACE_SPACE_AVAILABLE(reg);
 218 }
 219
 220 /**
 221  * dwc3_core_soft_reset - Issues core soft reset and PHY reset
 222  * @dwc: pointer to our context structure
 223  */
 224 static int dwc3_core_soft_reset(struct dwc3 *dwc)
 225 {
 226         u32             reg;
 227         int             retries = 1000;
 228         int             ret;
 229
 230         usb_phy_init(dwc->usb2_phy);
 231         usb_phy_init(dwc->usb3_phy);
 232         ret = phy_init(dwc->usb2_generic_phy);
 233         if (ret < 0)
 234                 return ret;
 235
 236         ret = phy_init(dwc->usb3_generic_phy);
 237         if (ret < 0) {
 238                 phy_exit(dwc->usb2_generic_phy);
 239                 return ret;
 240         }
 241
 242         /*
 243          * We're resetting only the device side because, if we're in host mode,
 244          * XHCI driver will reset the host block. If dwc3 was configured for
 245          * host-only mode, then we can return early.
 246          */
 247         if (dwc->current_dr_role == DWC3_GCTL_PRTCAP_HOST)
 248                 return 0;
 249
 250         reg = dwc3_readl(dwc->regs, DWC3_DCTL);
 251         reg |= DWC3_DCTL_CSFTRST;
 252         dwc3_writel(dwc->regs, DWC3_DCTL, reg);
 253
 254         do {
 255                 reg = dwc3_readl(dwc->regs, DWC3_DCTL);
 256                 if (!(reg & DWC3_DCTL_CSFTRST))
 257                         goto done;
 258
 259                 udelay(1);
 260         } while (--retries);
 261
 262         phy_exit(dwc->usb3_generic_phy);
 263         phy_exit(dwc->usb2_generic_phy);
 264
 265         return -ETIMEDOUT;
 266
 267 done:
 268         /*
 269          * For DWC_usb31 controller, once DWC3_DCTL_CSFTRST bit is cleared,
 270          * we must wait at least 50ms before accessing the PHY domain
 271          * (synchronization delay). DWC_usb31 programming guide section 1.3.2.
 272          */
 273         if (dwc3_is_usb31(dwc))
 274                 msleep(50);
 275
 276         return 0;
 277 }
 278
 279 static const struct clk_bulk_data dwc3_core_clks[] = {
 280         { .id = "ref" },
 281         { .id = "bus_early" },
 282         { .id = "suspend" },
 283 };
 284
 285 /*
 286  * dwc3_frame_length_adjustment - Adjusts frame length if required
 287  * @dwc3: Pointer to our controller context structure
 288  */
 289 static void dwc3_frame_length_adjustment(struct dwc3 *dwc)
 290 {
 291         u32 reg;
 292         u32 dft;
 293
 294         if (dwc->revision < DWC3_REVISION_250A)
 295                 return;
 296
 297         if (dwc->fladj == 0)
 298                 return;
 299
 300         reg = dwc3_readl(dwc->regs, DWC3_GFLADJ);
 301         dft = reg & DWC3_GFLADJ_30MHZ_MASK;
 302         if (!dev_WARN_ONCE(dwc->dev, dft == dwc->fladj,
 303             "request value same as default, ignoring\n")) {
 304                 reg &= ~DWC3_GFLADJ_30MHZ_MASK;
 305                 reg |= DWC3_GFLADJ_30MHZ_SDBND_SEL | dwc->fladj;
 306                 dwc3_writel(dwc->regs, DWC3_GFLADJ, reg);
 307         }
 308 }
 309
 310 /**
 311  * dwc3_free_one_event_buffer - Frees one event buffer
 312  * @dwc: Pointer to our controller context structure
 313  * @evt: Pointer to event buffer to be freed
 314  */
 315 static void dwc3_free_one_event_buffer(struct dwc3 *dwc,
 316                 struct dwc3_event_buffer *evt)
 317 {
 318         dma_free_coherent(dwc->sysdev, evt->length, evt->buf, evt->dma);
 319 }
 320
 321 /**
 322  * dwc3_alloc_one_event_buffer - Allocates one event buffer structure
 323  * @dwc: Pointer to our controller context structure
 324  * @length: size of the event buffer
 325  *
 326  * Returns a pointer to the allocated event buffer structure on success
 327  * otherwise ERR_PTR(errno).
 328  */
 329 static struct dwc3_event_buffer *dwc3_alloc_one_event_buffer(struct dwc3 *dwc,
 330                 unsigned length)
 331 {
 332         struct dwc3_event_buffer        *evt;
 333
 334         evt = devm_kzalloc(dwc->dev, sizeof(*evt), GFP_KERNEL);
 335         if (!evt)
 336                 return ERR_PTR(-ENOMEM);
 337
 338         evt->dwc        = dwc;
 339         evt->length     = length;
 340         evt->cache      = devm_kzalloc(dwc->dev, length, GFP_KERNEL);
 341         if (!evt->cache)
 342                 return ERR_PTR(-ENOMEM);
 343
 344         evt->buf        = dma_alloc_coherent(dwc->sysdev, length,
 345                         &evt->dma, GFP_KERNEL);
 346         if (!evt->buf)
 347                 return ERR_PTR(-ENOMEM);
 348
 349         return evt;
 350 }
 351
 352 /**
 353  * dwc3_free_event_buffers - frees all allocated event buffers
 354  * @dwc: Pointer to our controller context structure
 355  */
 356 static void dwc3_free_event_buffers(struct dwc3 *dwc)
 357 {
 358         struct dwc3_event_buffer        *evt;
 359
 360         evt = dwc->ev_buf;
 361         if (evt)
 362                 dwc3_free_one_event_buffer(dwc, evt);
 363 }
 364
 365 /**
 366  * dwc3_alloc_event_buffers - Allocates @num event buffers of size @length
 367  * @dwc: pointer to our controller context structure
 368  * @length: size of event buffer
 369  *
 370  * Returns 0 on success otherwise negative errno. In the error case, dwc
 371  * may contain some buffers allocated but not all which were requested.
 372  */
 373 static int dwc3_alloc_event_buffers(struct dwc3 *dwc, unsigned length)
 374 {
 375         struct dwc3_event_buffer *evt;
 376
 377         evt = dwc3_alloc_one_event_buffer(dwc, length);
 378         if (IS_ERR(evt)) {
 379                 dev_err(dwc->dev, "can't allocate event buffer\n");
 380                 return PTR_ERR(evt);
 381         }
 382         dwc->ev_buf = evt;
 383
 384         return 0;
 385 }
 386
 387 /**
 388  * dwc3_event_buffers_setup - setup our allocated event buffers
 389  * @dwc: pointer to our controller context structure
 390  *
 391  * Returns 0 on success otherwise negative errno.
 392  */
 393 int dwc3_event_buffers_setup(struct dwc3 *dwc)
 394 {
 395         struct dwc3_event_buffer        *evt;
 396
 397         evt = dwc->ev_buf;
 398         evt->lpos = 0;
 399         dwc3_writel(dwc->regs, DWC3_GEVNTADRLO(0),
 400                         lower_32_bits(evt->dma));
 401         dwc3_writel(dwc->regs, DWC3_GEVNTADRHI(0),
 402                         upper_32_bits(evt->dma));
 403         dwc3_writel(dwc->regs, DWC3_GEVNTSIZ(0),
 404                         DWC3_GEVNTSIZ_SIZE(evt->length));
 405         dwc3_writel(dwc->regs, DWC3_GEVNTCOUNT(0), 0);
 406
 407         return 0;
 408 }
 409
 410 void dwc3_event_buffers_cleanup(struct dwc3 *dwc)
 411 {
 412         struct dwc3_event_buffer        *evt;
 413
 414         evt = dwc->ev_buf;
 415
 416         evt->lpos = 0;
 417
 418         dwc3_writel(dwc->regs, DWC3_GEVNTADRLO(0), 0);
 419         dwc3_writel(dwc->regs, DWC3_GEVNTADRHI(0), 0);
 420         dwc3_writel(dwc->regs, DWC3_GEVNTSIZ(0), DWC3_GEVNTSIZ_INTMASK
 421                         | DWC3_GEVNTSIZ_SIZE(0));
 422         dwc3_writel(dwc->regs, DWC3_GEVNTCOUNT(0), 0);
 423 }
 424
 425 static int dwc3_alloc_scratch_buffers(struct dwc3 *dwc)
 426 {
 427         if (!dwc->has_hibernation)
 428                 return 0;
 429
 430         if (!dwc->nr_scratch)
 431                 return 0;
 432
 433         dwc->scratchbuf = kmalloc_array(dwc->nr_scratch,
 434                         DWC3_SCRATCHBUF_SIZE, GFP_KERNEL);
 435         if (!dwc->scratchbuf)
 436                 return -ENOMEM;
 437
 438         return 0;
 439 }
 440
 441 static int dwc3_setup_scratch_buffers(struct dwc3 *dwc)
 442 {
 443         dma_addr_t scratch_addr;
 444         u32 param;
 445         int ret;
 446
 447         if (!dwc->has_hibernation)
 448                 return 0;
 449
 450         if (!dwc->nr_scratch)
 451                 return 0;
 452
 453          /* should never fall here */
 454         if (!WARN_ON(dwc->scratchbuf))
 455                 return 0;
 456
 457         scratch_addr = dma_map_single(dwc->sysdev, dwc->scratchbuf,
 458                         dwc->nr_scratch * DWC3_SCRATCHBUF_SIZE,
 459                         DMA_BIDIRECTIONAL);
 460         if (dma_mapping_error(dwc->sysdev, scratch_addr)) {
 461                 dev_err(dwc->sysdev, "failed to map scratch buffer\n");
 462                 ret = -EFAULT;
 463                 goto err0;
 464         }
 465
 466         dwc->scratch_addr = scratch_addr;
 467
 468         param = lower_32_bits(scratch_addr);
 469
 470         ret = dwc3_send_gadget_generic_command(dwc,
 471                         DWC3_DGCMD_SET_SCRATCHPAD_ADDR_LO, param);
 472         if (ret < 0)
 473                 goto err1;
 474
 475         param = upper_32_bits(scratch_addr);
 476
 477         ret = dwc3_send_gadget_generic_command(dwc,
 478                         DWC3_DGCMD_SET_SCRATCHPAD_ADDR_HI, param);
 479         if (ret < 0)
 480                 goto err1;
 481
 482         return 0;
 483
 484 err1:
 485         dma_unmap_single(dwc->sysdev, dwc->scratch_addr, dwc->nr_scratch *
 486                         DWC3_SCRATCHBUF_SIZE, DMA_BIDIRECTIONAL);
 487
 488 err0:
 489         return ret;
 490 }
 491
 492 static void dwc3_free_scratch_buffers(struct dwc3 *dwc)
 493 {
 494         if (!dwc->has_hibernation)
 495                 return;
 496
 497         if (!dwc->nr_scratch)
 498                 return;
 499
 500          /* should never fall here */
 501         if (!WARN_ON(dwc->scratchbuf))
 502                 return;
 503
 504         dma_unmap_single(dwc->sysdev, dwc->scratch_addr, dwc->nr_scratch *
 505                         DWC3_SCRATCHBUF_SIZE, DMA_BIDIRECTIONAL);
 506         kfree(dwc->scratchbuf);
 507 }
 508
 509 static void dwc3_core_num_eps(struct dwc3 *dwc)
 510 {
 511         struct dwc3_hwparams    *parms = &dwc->hwparams;
 512
 513         dwc->num_eps = DWC3_NUM_EPS(parms);
 514 }
 515
 516 static void dwc3_cache_hwparams(struct dwc3 *dwc)
 517 {
 518         struct dwc3_hwparams    *parms = &dwc->hwparams;
 519
 520         parms->hwparams0 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS0);
 521         parms->hwparams1 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS1);
 522         parms->hwparams2 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS2);
 523         parms->hwparams3 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS3);
 524         parms->hwparams4 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS4);
 525         parms->hwparams5 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS5);
 526         parms->hwparams6 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS6);
 527         parms->hwparams7 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS7);
 528         parms->hwparams8 = dwc3_readl(dwc->regs, DWC3_GHWPARAMS8);
 529 }
 530
 531 static int dwc3_core_ulpi_init(struct dwc3 *dwc)
 532 {
 533         int intf;
 534         int ret = 0;
 535
 536         intf = DWC3_GHWPARAMS3_HSPHY_IFC(dwc->hwparams.hwparams3);
 537
 538         if (intf == DWC3_GHWPARAMS3_HSPHY_IFC_ULPI ||
 539             (intf == DWC3_GHWPARAMS3_HSPHY_IFC_UTMI_ULPI &&
 540              dwc->hsphy_interface &&
 541              !strncmp(dwc->hsphy_interface, "ulpi", 4)))
 542                 ret = dwc3_ulpi_init(dwc);
 543
 544         return ret;
 545 }
 546
 547 /**
 548  * dwc3_phy_setup - Configure USB PHY Interface of DWC3 Core
 549  * @dwc: Pointer to our controller context structure
 550  *
 551  * Returns 0 on success. The USB PHY interfaces are configured but not
 552  * initialized. The PHY interfaces and the PHYs get initialized together with
 553  * the core in dwc3_core_init.
 554  */
 555 static int dwc3_phy_setup(struct dwc3 *dwc)
 556 {
 557         u32 reg;
 558
 559         reg = dwc3_readl(dwc->regs, DWC3_GUSB3PIPECTL(0));
 560
 561         /*
 562          * Make sure UX_EXIT_PX is cleared as that causes issues with some
 563          * PHYs. Also, this bit is not supposed to be used in normal operation.
 564          */
 565         reg &= ~DWC3_GUSB3PIPECTL_UX_EXIT_PX;
 566
 567         /*
 568          * Above 1.94a, it is recommended to set DWC3_GUSB3PIPECTL_SUSPHY
 569          * to '0' during coreConsultant configuration. So default value
 570          * will be '0' when the core is reset. Application needs to set it
 571          * to '1' after the core initialization is completed.
 572          */
 573         if (dwc->revision > DWC3_REVISION_194A)
 574                 reg |= DWC3_GUSB3PIPECTL_SUSPHY;
 575
 576         if (dwc->u2ss_inp3_quirk)
 577                 reg |= DWC3_GUSB3PIPECTL_U2SSINP3OK;
 578
 579         if (dwc->dis_rxdet_inp3_quirk)
 580                 reg |= DWC3_GUSB3PIPECTL_DISRXDETINP3;
 581
 582         if (dwc->req_p1p2p3_quirk)
 583                 reg |= DWC3_GUSB3PIPECTL_REQP1P2P3;
 584
 585         if (dwc->del_p1p2p3_quirk)
 586                 reg |= DWC3_GUSB3PIPECTL_DEP1P2P3_EN;
 587
 588         if (dwc->del_phy_power_chg_quirk)
 589                 reg |= DWC3_GUSB3PIPECTL_DEPOCHANGE;
 590
 591         if (dwc->lfps_filter_quirk)
 592                 reg |= DWC3_GUSB3PIPECTL_LFPSFILT;
 593
 594         if (dwc->rx_detect_poll_quirk)
 595                 reg |= DWC3_GUSB3PIPECTL_RX_DETOPOLL;
 596
 597         if (dwc->tx_de_emphasis_quirk)
 598                 reg |= DWC3_GUSB3PIPECTL_TX_DEEPH(dwc->tx_de_emphasis);
 599
 600         if (dwc->dis_u3_susphy_quirk)
 601                 reg &= ~DWC3_GUSB3PIPECTL_SUSPHY;
 602
 603         if (dwc->dis_del_phy_power_chg_quirk)
 604                 reg &= ~DWC3_GUSB3PIPECTL_DEPOCHANGE;
 605
 606         dwc3_writel(dwc->regs, DWC3_GUSB3PIPECTL(0), reg);
 607
 608         reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0));
 609
 610         /* Select the HS PHY interface */
 611         switch (DWC3_GHWPARAMS3_HSPHY_IFC(dwc->hwparams.hwparams3)) {
 612         case DWC3_GHWPARAMS3_HSPHY_IFC_UTMI_ULPI:
 613                 if (dwc->hsphy_interface &&
 614                                 !strncmp(dwc->hsphy_interface, "utmi", 4)) {
 615                         reg &= ~DWC3_GUSB2PHYCFG_ULPI_UTMI;
 616                         break;
 617                 } else if (dwc->hsphy_interface &&
 618                                 !strncmp(dwc->hsphy_interface, "ulpi", 4)) {
 619                         reg |= DWC3_GUSB2PHYCFG_ULPI_UTMI;
 620                         dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg);
 621                 } else {
 622                         /* Relying on default value. */
 623                         if (!(reg & DWC3_GUSB2PHYCFG_ULPI_UTMI))
 624                                 break;
 625                 }
 626                 /* FALLTHROUGH */
 627         case DWC3_GHWPARAMS3_HSPHY_IFC_ULPI:
 628                 /* FALLTHROUGH */
 629         default:
 630                 break;
 631         }
 632
 633         switch (dwc->hsphy_mode) {
 634         case USBPHY_INTERFACE_MODE_UTMI:
 635                 reg &= ~(DWC3_GUSB2PHYCFG_PHYIF_MASK |
 636                        DWC3_GUSB2PHYCFG_USBTRDTIM_MASK);
 637                 reg |= DWC3_GUSB2PHYCFG_PHYIF(UTMI_PHYIF_8_BIT) |
 638                        DWC3_GUSB2PHYCFG_USBTRDTIM(USBTRDTIM_UTMI_8_BIT);
 639                 break;
 640         case USBPHY_INTERFACE_MODE_UTMIW:
 641                 reg &= ~(DWC3_GUSB2PHYCFG_PHYIF_MASK |
 642                        DWC3_GUSB2PHYCFG_USBTRDTIM_MASK);
 643                 reg |= DWC3_GUSB2PHYCFG_PHYIF(UTMI_PHYIF_16_BIT) |
 644                        DWC3_GUSB2PHYCFG_USBTRDTIM(USBTRDTIM_UTMI_16_BIT);
 645                 break;
 646         default:
 647                 break;
 648         }
 649
 650         /*
 651          * Above 1.94a, it is recommended to set DWC3_GUSB2PHYCFG_SUSPHY to
 652          * '0' during coreConsultant configuration. So default value will
 653          * be '0' when the core is reset. Application needs to set it to
 654          * '1' after the core initialization is completed.
 655          */
 656         if (dwc->revision > DWC3_REVISION_194A)
 657                 reg |= DWC3_GUSB2PHYCFG_SUSPHY;
 658
 659         if (dwc->dis_u2_susphy_quirk)
 660                 reg &= ~DWC3_GUSB2PHYCFG_SUSPHY;
 661
 662         if (dwc->dis_enblslpm_quirk)
 663                 reg &= ~DWC3_GUSB2PHYCFG_ENBLSLPM;
 664
 665         if (dwc->dis_u2_freeclk_exists_quirk)
 666                 reg &= ~DWC3_GUSB2PHYCFG_U2_FREECLK_EXISTS;
 667
 668         dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg);
 669
 670         return 0;
 671 }
 672
 673 static void dwc3_core_exit(struct dwc3 *dwc)
 674 {
 675         dwc3_event_buffers_cleanup(dwc);
 676
 677         usb_phy_shutdown(dwc->usb2_phy);
 678         usb_phy_shutdown(dwc->usb3_phy);
 679         phy_exit(dwc->usb2_generic_phy);
 680         phy_exit(dwc->usb3_generic_phy);
 681
 682         usb_phy_set_suspend(dwc->usb2_phy, 1);
 683         usb_phy_set_suspend(dwc->usb3_phy, 1);
 684         phy_power_off(dwc->usb2_generic_phy);
 685         phy_power_off(dwc->usb3_generic_phy);
 686         clk_bulk_disable(dwc->num_clks, dwc->clks);
 687         clk_bulk_unprepare(dwc->num_clks, dwc->clks);
 688         reset_control_assert(dwc->reset);
 689 }
 690
 691 static bool dwc3_core_is_valid(struct dwc3 *dwc)
 692 {
 693         u32 reg;
 694
 695         reg = dwc3_readl(dwc->regs, DWC3_GSNPSID);
 696
 697         /* This should read as U3 followed by revision number */
 698         if ((reg & DWC3_GSNPSID_MASK) == 0x55330000) {
 699                 /* Detected DWC_usb3 IP */
 700                 dwc->revision = reg;
 701         } else if ((reg & DWC3_GSNPSID_MASK) == 0x33310000) {
 702                 /* Detected DWC_usb31 IP */
 703                 dwc->revision = dwc3_readl(dwc->regs, DWC3_VER_NUMBER);
 704                 dwc->revision |= DWC3_REVISION_IS_DWC31;
 705         } else {
 706                 return false;
 707         }
 708
 709         return true;
 710 }
 711
 712 static void dwc3_core_setup_global_control(struct dwc3 *dwc)
 713 {
 714         u32 hwparams4 = dwc->hwparams.hwparams4;
 715         u32 reg;
 716
 717         reg = dwc3_readl(dwc->regs, DWC3_GCTL);
 718         reg &= ~DWC3_GCTL_SCALEDOWN_MASK;
 719
 720         switch (DWC3_GHWPARAMS1_EN_PWROPT(dwc->hwparams.hwparams1)) {
 721         case DWC3_GHWPARAMS1_EN_PWROPT_CLK:
 722                 /**
 723                  * WORKAROUND: DWC3 revisions between 2.10a and 2.50a have an
 724                  * issue which would cause xHCI compliance tests to fail.
 725                  *
 726                  * Because of that we cannot enable clock gating on such
 727                  * configurations.
 728                  *
 729                  * Refers to:
 730                  *
 731                  * STAR#9000588375: Clock Gating, SOF Issues when ref_clk-Based
 732                  * SOF/ITP Mode Used
 733                  */
 734                 if ((dwc->dr_mode == USB_DR_MODE_HOST ||
 735                                 dwc->dr_mode == USB_DR_MODE_OTG) &&
 736                                 (dwc->revision >= DWC3_REVISION_210A &&
 737                                 dwc->revision <= DWC3_REVISION_250A))
 738                         reg |= DWC3_GCTL_DSBLCLKGTNG | DWC3_GCTL_SOFITPSYNC;
 739                 else
 740                         reg &= ~DWC3_GCTL_DSBLCLKGTNG;
 741                 break;
 742         case DWC3_GHWPARAMS1_EN_PWROPT_HIB:
 743                 /* enable hibernation here */
 744                 dwc->nr_scratch = DWC3_GHWPARAMS4_HIBER_SCRATCHBUFS(hwparams4);
 745
 746                 /*
 747                  * REVISIT Enabling this bit so that host-mode hibernation
 748                  * will work. Device-mode hibernation is not yet implemented.
 749                  */
 750                 reg |= DWC3_GCTL_GBLHIBERNATIONEN;
 751                 break;
 752         default:
 753                 /* nothing */
 754                 break;
 755         }
 756
 757         /* check if current dwc3 is on simulation board */
 758         if (dwc->hwparams.hwparams6 & DWC3_GHWPARAMS6_EN_FPGA) {
 759                 dev_info(dwc->dev, "Running with FPGA optimizations\n");
 760                 dwc->is_fpga = true;
 761         }
 762
 763         WARN_ONCE(dwc->disable_scramble_quirk && !dwc->is_fpga,
 764                         "disable_scramble cannot be used on non-FPGA builds\n");
 765
 766         if (dwc->disable_scramble_quirk && dwc->is_fpga)
 767                 reg |= DWC3_GCTL_DISSCRAMBLE;
 768         else
 769                 reg &= ~DWC3_GCTL_DISSCRAMBLE;
 770
 771         if (dwc->u2exit_lfps_quirk)
 772                 reg |= DWC3_GCTL_U2EXIT_LFPS;
 773
 774         /*
 775          * WORKAROUND: DWC3 revisions <1.90a have a bug
 776          * where the device can fail to connect at SuperSpeed
 777          * and falls back to high-speed mode which causes
 778          * the device to enter a Connect/Disconnect loop
 779          */
 780         if (dwc->revision < DWC3_REVISION_190A)
 781                 reg |= DWC3_GCTL_U2RSTECN;
 782
 783         dwc3_writel(dwc->regs, DWC3_GCTL, reg);
 784 }
 785
 786 static int dwc3_core_get_phy(struct dwc3 *dwc);
 787 static int dwc3_core_ulpi_init(struct dwc3 *dwc);
 788
 789 /* set global incr burst type configuration registers */
 790 static void dwc3_set_incr_burst_type(struct dwc3 *dwc)
 791 {
 792         struct device *dev = dwc->dev;
 793         /* incrx_mode : for INCR burst type. */
 794         bool incrx_mode;
 795         /* incrx_size : for size of INCRX burst. */
 796         u32 incrx_size;
 797         u32 *vals;
 798         u32 cfg;
 799         int ntype;
 800         int ret;
 801         int i;
 802
 803         cfg = dwc3_readl(dwc->regs, DWC3_GSBUSCFG0);
 804
 805         /*
 806          * Handle property "snps,incr-burst-type-adjustment".
 807          * Get the number of value from this property:
 808          * result <= 0, means this property is not supported.
 809          * result = 1, means INCRx burst mode supported.
 810          * result > 1, means undefined length burst mode supported.
 811          */
 812         ntype = device_property_read_u32_array(dev,
 813                         "snps,incr-burst-type-adjustment", NULL, 0);
 814         if (ntype <= 0)
 815                 return;
 816
 817         vals = kcalloc(ntype, sizeof(u32), GFP_KERNEL);
 818         if (!vals) {
 819                 dev_err(dev, "Error to get memory\n");
 820                 return;
 821         }
 822
 823         /* Get INCR burst type, and parse it */
 824         ret = device_property_read_u32_array(dev,
 825                         "snps,incr-burst-type-adjustment", vals, ntype);
 826         if (ret) {
 827                 dev_err(dev, "Error to get property\n");
 828                 return;
 829         }
 830
 831         incrx_size = *vals;
 832
 833         if (ntype > 1) {
 834                 /* INCRX (undefined length) burst mode */
 835                 incrx_mode = INCRX_UNDEF_LENGTH_BURST_MODE;
 836                 for (i = 1; i < ntype; i++) {
 837                         if (vals[i] > incrx_size)
 838                                 incrx_size = vals[i];
 839                 }
 840         } else {
 841                 /* INCRX burst mode */
 842                 incrx_mode = INCRX_BURST_MODE;
 843         }
 844
 845         /* Enable Undefined Length INCR Burst and Enable INCRx Burst */
 846         cfg &= ~DWC3_GSBUSCFG0_INCRBRST_MASK;
 847         if (incrx_mode)
 848                 cfg |= DWC3_GSBUSCFG0_INCRBRSTENA;
 849         switch (incrx_size) {
 850         case 256:
 851                 cfg |= DWC3_GSBUSCFG0_INCR256BRSTENA;
 852                 break;
 853         case 128:
 854                 cfg |= DWC3_GSBUSCFG0_INCR128BRSTENA;
 855                 break;
 856         case 64:
 857                 cfg |= DWC3_GSBUSCFG0_INCR64BRSTENA;
 858                 break;
 859         case 32:
 860                 cfg |= DWC3_GSBUSCFG0_INCR32BRSTENA;
 861                 break;
 862         case 16:
 863                 cfg |= DWC3_GSBUSCFG0_INCR16BRSTENA;
 864                 break;
 865         case 8:
 866                 cfg |= DWC3_GSBUSCFG0_INCR8BRSTENA;
 867                 break;
 868         case 4:
 869                 cfg |= DWC3_GSBUSCFG0_INCR4BRSTENA;
 870                 break;
 871         case 1:
 872                 break;
 873         default:
 874                 dev_err(dev, "Invalid property\n");
 875                 break;
 876         }
 877
 878         dwc3_writel(dwc->regs, DWC3_GSBUSCFG0, cfg);
 879 }
 880
 881 /**
 882  * dwc3_core_init - Low-level initialization of DWC3 Core
 883  * @dwc: Pointer to our controller context structure
 884  *
 885  * Returns 0 on success otherwise negative errno.
 886  */
 887 static int dwc3_core_init(struct dwc3 *dwc)
 888 {
 889         u32                     reg;
 890         int                     ret;
 891
 892         if (!dwc3_core_is_valid(dwc)) {
 893                 dev_err(dwc->dev, "this is not a DesignWare USB3 DRD Core\n");
 894                 ret = -ENODEV;
 895                 goto err0;
 896         }
 897
 898         /*
 899          * Write Linux Version Code to our GUID register so it's easy to figure
 900          * out which kernel version a bug was found.
 901          */
 902         dwc3_writel(dwc->regs, DWC3_GUID, LINUX_VERSION_CODE);
 903
 904         /* Handle USB2.0-only core configuration */
 905         if (DWC3_GHWPARAMS3_SSPHY_IFC(dwc->hwparams.hwparams3) ==
 906                         DWC3_GHWPARAMS3_SSPHY_IFC_DIS) {
 907                 if (dwc->maximum_speed == USB_SPEED_SUPER)
 908                         dwc->maximum_speed = USB_SPEED_HIGH;
 909         }
 910
 911         ret = dwc3_phy_setup(dwc);
 912         if (ret)
 913                 goto err0;
 914
 915         if (!dwc->ulpi_ready) {
 916                 ret = dwc3_core_ulpi_init(dwc);
 917                 if (ret)
 918                         goto err0;
 919                 dwc->ulpi_ready = true;
 920         }
 921
 922         if (!dwc->phys_ready) {
 923                 ret = dwc3_core_get_phy(dwc);
 924                 if (ret)
 925                         goto err0a;
 926                 dwc->phys_ready = true;
 927         }
 928
 929         ret = dwc3_core_soft_reset(dwc);
 930         if (ret)
 931                 goto err0a;
 932
 933         dwc3_core_setup_global_control(dwc);
 934         dwc3_core_num_eps(dwc);
 935
 936         ret = dwc3_setup_scratch_buffers(dwc);
 937         if (ret)
 938                 goto err1;
 939
 940         /* Adjust Frame Length */
 941         dwc3_frame_length_adjustment(dwc);
 942
 943         dwc3_set_incr_burst_type(dwc);
 944
 945         usb_phy_set_suspend(dwc->usb2_phy, 0);
 946         usb_phy_set_suspend(dwc->usb3_phy, 0);
 947         ret = phy_power_on(dwc->usb2_generic_phy);
 948         if (ret < 0)
 949                 goto err2;
 950
 951         ret = phy_power_on(dwc->usb3_generic_phy);
 952         if (ret < 0)
 953                 goto err3;
 954
 955         ret = dwc3_event_buffers_setup(dwc);
 956         if (ret) {
 957                 dev_err(dwc->dev, "failed to setup event buffers\n");
 958                 goto err4;
 959         }
 960
 961         /*
 962          * ENDXFER polling is available on version 3.10a and later of
 963          * the DWC_usb3 controller. It is NOT available in the
 964          * DWC_usb31 controller.
 965          */
 966         if (!dwc3_is_usb31(dwc) && dwc->revision >= DWC3_REVISION_310A) {
 967                 reg = dwc3_readl(dwc->regs, DWC3_GUCTL2);
 968                 reg |= DWC3_GUCTL2_RST_ACTBITLATER;
 969                 dwc3_writel(dwc->regs, DWC3_GUCTL2, reg);
 970         }
 971
 972         if (dwc->revision >= DWC3_REVISION_250A) {
 973                 reg = dwc3_readl(dwc->regs, DWC3_GUCTL1);
 974
 975                 /*
 976                  * Enable hardware control of sending remote wakeup
 977                  * in HS when the device is in the L1 state.
 978                  */
 979                 if (dwc->revision >= DWC3_REVISION_290A)
 980                         reg |= DWC3_GUCTL1_DEV_L1_EXIT_BY_HW;
 981
 982                 if (dwc->dis_tx_ipgap_linecheck_quirk)
 983                         reg |= DWC3_GUCTL1_TX_IPGAP_LINECHECK_DIS;
 984
 985                 dwc3_writel(dwc->regs, DWC3_GUCTL1, reg);
 986         }
 987
 988         if (dwc->dr_mode == USB_DR_MODE_HOST ||
 989             dwc->dr_mode == USB_DR_MODE_OTG) {
 990                 reg = dwc3_readl(dwc->regs, DWC3_GUCTL);
 991
 992                 /*
 993                  * Enable Auto retry Feature to make the controller operating in
 994                  * Host mode on seeing transaction errors(CRC errors or internal
 995                  * overrun scenerios) on IN transfers to reply to the device
 996                  * with a non-terminating retry ACK (i.e, an ACK transcation
 997                  * packet with Retry=1 & Nump != 0)
 998                  */
 999                 reg |= DWC3_GUCTL_HSTINAUTORETRY;
1000
1001                 dwc3_writel(dwc->regs, DWC3_GUCTL, reg);
1002         }
1003
1004         /*
1005          * Must config both number of packets and max burst settings to enable
1006          * RX and/or TX threshold.
1007          */
1008         if (dwc3_is_usb31(dwc) && dwc->dr_mode == USB_DR_MODE_HOST) {
1009                 u8 rx_thr_num = dwc->rx_thr_num_pkt_prd;
1010                 u8 rx_maxburst = dwc->rx_max_burst_prd;
1011                 u8 tx_thr_num = dwc->tx_thr_num_pkt_prd;
1012                 u8 tx_maxburst = dwc->tx_max_burst_prd;
1013
1014                 if (rx_thr_num && rx_maxburst) {
1015                         reg = dwc3_readl(dwc->regs, DWC3_GRXTHRCFG);
1016                         reg |= DWC31_RXTHRNUMPKTSEL_PRD;
1017
1018                         reg &= ~DWC31_RXTHRNUMPKT_PRD(~0);
1019                         reg |= DWC31_RXTHRNUMPKT_PRD(rx_thr_num);
1020
1021                         reg &= ~DWC31_MAXRXBURSTSIZE_PRD(~0);
1022                         reg |= DWC31_MAXRXBURSTSIZE_PRD(rx_maxburst);
1023
1024                         dwc3_writel(dwc->regs, DWC3_GRXTHRCFG, reg);
1025                 }
1026
1027                 if (tx_thr_num && tx_maxburst) {
1028                         reg = dwc3_readl(dwc->regs, DWC3_GTXTHRCFG);
1029                         reg |= DWC31_TXTHRNUMPKTSEL_PRD;
1030
1031                         reg &= ~DWC31_TXTHRNUMPKT_PRD(~0);
1032                         reg |= DWC31_TXTHRNUMPKT_PRD(tx_thr_num);
1033
1034                         reg &= ~DWC31_MAXTXBURSTSIZE_PRD(~0);
1035                         reg |= DWC31_MAXTXBURSTSIZE_PRD(tx_maxburst);
1036
1037                         dwc3_writel(dwc->regs, DWC3_GTXTHRCFG, reg);
1038                 }
1039         }
1040
1041         return 0;
1042
1043 err4:
1044         phy_power_off(dwc->usb3_generic_phy);
1045
1046 err3:
1047         phy_power_off(dwc->usb2_generic_phy);
1048
1049 err2:
1050         usb_phy_set_suspend(dwc->usb2_phy, 1);
1051         usb_phy_set_suspend(dwc->usb3_phy, 1);
1052
1053 err1:
1054         usb_phy_shutdown(dwc->usb2_phy);
1055         usb_phy_shutdown(dwc->usb3_phy);
1056         phy_exit(dwc->usb2_generic_phy);
1057         phy_exit(dwc->usb3_generic_phy);
1058
1059 err0a:
1060         dwc3_ulpi_exit(dwc);
1061
1062 err0:
1063         return ret;
1064 }
1065
1066 static int dwc3_core_get_phy(struct dwc3 *dwc)
1067 {
1068         struct device           *dev = dwc->dev;
1069         struct device_node      *node = dev->of_node;
1070         int ret;
1071
1072         if (node) {
1073                 dwc->usb2_phy = devm_usb_get_phy_by_phandle(dev, "usb-phy", 0);
1074                 dwc->usb3_phy = devm_usb_get_phy_by_phandle(dev, "usb-phy", 1);
1075         } else {
1076                 dwc->usb2_phy = devm_usb_get_phy(dev, USB_PHY_TYPE_USB2);
1077                 dwc->usb3_phy = devm_usb_get_phy(dev, USB_PHY_TYPE_USB3);
1078         }
1079
1080         if (IS_ERR(dwc->usb2_phy)) {
1081                 ret = PTR_ERR(dwc->usb2_phy);
1082                 if (ret == -ENXIO || ret == -ENODEV) {
1083                         dwc->usb2_phy = NULL;
1084                 } else if (ret == -EPROBE_DEFER) {
1085                         return ret;
1086                 } else {
1087                         dev_err(dev, "no usb2 phy configured\n");
1088                         return ret;
1089                 }
1090         }
1091
1092         if (IS_ERR(dwc->usb3_phy)) {
1093                 ret = PTR_ERR(dwc->usb3_phy);
1094                 if (ret == -ENXIO || ret == -ENODEV) {
1095                         dwc->usb3_phy = NULL;
1096                 } else if (ret == -EPROBE_DEFER) {
1097                         return ret;
1098                 } else {
1099                         dev_err(dev, "no usb3 phy configured\n");
1100                         return ret;
1101                 }
1102         }
1103
1104         dwc->usb2_generic_phy = devm_phy_get(dev, "usb2-phy");
1105         if (IS_ERR(dwc->usb2_generic_phy)) {
1106                 ret = PTR_ERR(dwc->usb2_generic_phy);
1107                 if (ret == -ENOSYS || ret == -ENODEV) {
1108                         dwc->usb2_generic_phy = NULL;
1109                 } else if (ret == -EPROBE_DEFER) {
1110                         return ret;
1111                 } else {
1112                         dev_err(dev, "no usb2 phy configured\n");
1113                         return ret;
1114                 }
1115         }
1116
1117         dwc->usb3_generic_phy = devm_phy_get(dev, "usb3-phy");
1118         if (IS_ERR(dwc->usb3_generic_phy)) {
1119                 ret = PTR_ERR(dwc->usb3_generic_phy);
1120                 if (ret == -ENOSYS || ret == -ENODEV) {
1121                         dwc->usb3_generic_phy = NULL;
1122                 } else if (ret == -EPROBE_DEFER) {
1123                         return ret;
1124                 } else {
1125                         dev_err(dev, "no usb3 phy configured\n");
1126                         return ret;
1127                 }
1128         }
1129
1130         return 0;
1131 }
1132
1133 static int dwc3_core_init_mode(struct dwc3 *dwc)
1134 {
1135         struct device *dev = dwc->dev;
1136         int ret;
1137
1138         switch (dwc->dr_mode) {
1139         case USB_DR_MODE_PERIPHERAL:
1140                 dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_DEVICE);
1141
1142                 if (dwc->usb2_phy)
1143                         otg_set_vbus(dwc->usb2_phy->otg, false);
1144                 phy_set_mode(dwc->usb2_generic_phy, PHY_MODE_USB_DEVICE);
1145                 phy_set_mode(dwc->usb3_generic_phy, PHY_MODE_USB_DEVICE);
1146
1147                 ret = dwc3_gadget_init(dwc);
1148                 if (ret) {
1149                         if (ret != -EPROBE_DEFER)
1150                                 dev_err(dev, "failed to initialize gadget\n");
1151                         return ret;
1152                 }
1153                 break;
1154         case USB_DR_MODE_HOST:
1155                 dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_HOST);
1156
1157                 if (dwc->usb2_phy)
1158                         otg_set_vbus(dwc->usb2_phy->otg, true);
1159                 phy_set_mode(dwc->usb2_generic_phy, PHY_MODE_USB_HOST);
1160                 phy_set_mode(dwc->usb3_generic_phy, PHY_MODE_USB_HOST);
1161
1162                 ret = dwc3_host_init(dwc);
1163                 if (ret) {
1164                         if (ret != -EPROBE_DEFER)
1165                                 dev_err(dev, "failed to initialize host\n");
1166                         return ret;
1167                 }
1168                 phy_calibrate(dwc->usb2_generic_phy);
1169                 break;
1170         case USB_DR_MODE_OTG:
1171                 INIT_WORK(&dwc->drd_work, __dwc3_set_mode);
1172                 ret = dwc3_drd_init(dwc);
1173                 if (ret) {
1174                         if (ret != -EPROBE_DEFER)
1175                                 dev_err(dev, "failed to initialize dual-role\n");
1176                         return ret;
1177                 }
1178                 break;
1179         default:
1180                 dev_err(dev, "Unsupported mode of operation %d\n", dwc->dr_mode);
1181                 return -EINVAL;
1182         }
1183
1184         return 0;
1185 }
1186
1187 static void dwc3_core_exit_mode(struct dwc3 *dwc)
1188 {
1189         switch (dwc->dr_mode) {
1190         case USB_DR_MODE_PERIPHERAL:
1191                 dwc3_gadget_exit(dwc);
1192                 break;
1193         case USB_DR_MODE_HOST:
1194                 dwc3_host_exit(dwc);
1195                 break;
1196         case USB_DR_MODE_OTG:
1197                 dwc3_drd_exit(dwc);
1198                 break;
1199         default:
1200                 /* do nothing */
1201                 break;
1202         }
1203 }
1204
1205 static void dwc3_get_properties(struct dwc3 *dwc)
1206 {
1207         struct device           *dev = dwc->dev;
1208         u8                      lpm_nyet_threshold;
1209         u8                      tx_de_emphasis;
1210         u8                      hird_threshold;
1211         u8                      rx_thr_num_pkt_prd;
1212         u8                      rx_max_burst_prd;
1213         u8                      tx_thr_num_pkt_prd;
1214         u8                      tx_max_burst_prd;
1215
1216         /* default to highest possible threshold */
1217         lpm_nyet_threshold = 0xff;
1218
1219         /* default to -3.5dB de-emphasis */
1220         tx_de_emphasis = 1;
1221
1222         /*
1223          * default to assert utmi_sleep_n and use maximum allowed HIRD
1224          * threshold value of 0b1100
1225          */
1226         hird_threshold = 12;
1227
1228         dwc->maximum_speed = usb_get_maximum_speed(dev);
1229         dwc->dr_mode = usb_get_dr_mode(dev);
1230         dwc->hsphy_mode = of_usb_get_phy_mode(dev->of_node);
1231
1232         dwc->sysdev_is_parent = device_property_read_bool(dev,
1233                                 "linux,sysdev_is_parent");
1234         if (dwc->sysdev_is_parent)
1235                 dwc->sysdev = dwc->dev->parent;
1236         else
1237                 dwc->sysdev = dwc->dev;
1238
1239         dwc->has_lpm_erratum = device_property_read_bool(dev,
1240                                 "snps,has-lpm-erratum");
1241         device_property_read_u8(dev, "snps,lpm-nyet-threshold",
1242                                 &lpm_nyet_threshold);
1243         dwc->is_utmi_l1_suspend = device_property_read_bool(dev,
1244                                 "snps,is-utmi-l1-suspend");
1245         device_property_read_u8(dev, "snps,hird-threshold",
1246                                 &hird_threshold);
1247         dwc->usb3_lpm_capable = device_property_read_bool(dev,
1248                                 "snps,usb3_lpm_capable");
1249         device_property_read_u8(dev, "snps,rx-thr-num-pkt-prd",
1250                                 &rx_thr_num_pkt_prd);
1251         device_property_read_u8(dev, "snps,rx-max-burst-prd",
1252                                 &rx_max_burst_prd);
1253         device_property_read_u8(dev, "snps,tx-thr-num-pkt-prd",
1254                                 &tx_thr_num_pkt_prd);
1255         device_property_read_u8(dev, "snps,tx-max-burst-prd",
1256                                 &tx_max_burst_prd);
1257
1258         dwc->disable_scramble_quirk = device_property_read_bool(dev,
1259                                 "snps,disable_scramble_quirk");
1260         dwc->u2exit_lfps_quirk = device_property_read_bool(dev,
1261                                 "snps,u2exit_lfps_quirk");
1262         dwc->u2ss_inp3_quirk = device_property_read_bool(dev,
1263                                 "snps,u2ss_inp3_quirk");
1264         dwc->req_p1p2p3_quirk = device_property_read_bool(dev,
1265                                 "snps,req_p1p2p3_quirk");
1266         dwc->del_p1p2p3_quirk = device_property_read_bool(dev,
1267                                 "snps,del_p1p2p3_quirk");
1268         dwc->del_phy_power_chg_quirk = device_property_read_bool(dev,
1269                                 "snps,del_phy_power_chg_quirk");
1270         dwc->lfps_filter_quirk = device_property_read_bool(dev,
1271                                 "snps,lfps_filter_quirk");
1272         dwc->rx_detect_poll_quirk = device_property_read_bool(dev,
1273                                 "snps,rx_detect_poll_quirk");
1274         dwc->dis_u3_susphy_quirk = device_property_read_bool(dev,
1275                                 "snps,dis_u3_susphy_quirk");
1276         dwc->dis_u2_susphy_quirk = device_property_read_bool(dev,
1277                                 "snps,dis_u2_susphy_quirk");
1278         dwc->dis_enblslpm_quirk = device_property_read_bool(dev,
1279                                 "snps,dis_enblslpm_quirk");
1280         dwc->dis_rxdet_inp3_quirk = device_property_read_bool(dev,
1281                                 "snps,dis_rxdet_inp3_quirk");
1282         dwc->dis_u2_freeclk_exists_quirk = device_property_read_bool(dev,
1283                                 "snps,dis-u2-freeclk-exists-quirk");
1284         dwc->dis_del_phy_power_chg_quirk = device_property_read_bool(dev,
1285                                 "snps,dis-del-phy-power-chg-quirk");
1286         dwc->dis_tx_ipgap_linecheck_quirk = device_property_read_bool(dev,
1287                                 "snps,dis-tx-ipgap-linecheck-quirk");
1288
1289         dwc->tx_de_emphasis_quirk = device_property_read_bool(dev,
1290                                 "snps,tx_de_emphasis_quirk");
1291         device_property_read_u8(dev, "snps,tx_de_emphasis",
1292                                 &tx_de_emphasis);
1293         device_property_read_string(dev, "snps,hsphy_interface",
1294                                     &dwc->hsphy_interface);
1295         device_property_read_u32(dev, "snps,quirk-frame-length-adjustment",
1296                                  &dwc->fladj);
1297
1298         dwc->dis_metastability_quirk = device_property_read_bool(dev,
1299                                 "snps,dis_metastability_quirk");
1300
1301         dwc->lpm_nyet_threshold = lpm_nyet_threshold;
1302         dwc->tx_de_emphasis = tx_de_emphasis;
1303
1304         dwc->hird_threshold = hird_threshold
1305                 | (dwc->is_utmi_l1_suspend << 4);
1306
1307         dwc->rx_thr_num_pkt_prd = rx_thr_num_pkt_prd;
1308         dwc->rx_max_burst_prd = rx_max_burst_prd;
1309
1310         dwc->tx_thr_num_pkt_prd = tx_thr_num_pkt_prd;
1311         dwc->tx_max_burst_prd = tx_max_burst_prd;
1312
1313         dwc->imod_interval = 0;
1314 }
1315
1316 /* check whether the core supports IMOD */
1317 bool dwc3_has_imod(struct dwc3 *dwc)
1318 {
1319         return ((dwc3_is_usb3(dwc) &&
1320                  dwc->revision >= DWC3_REVISION_300A) ||
1321                 (dwc3_is_usb31(dwc) &&
1322                  dwc->revision >= DWC3_USB31_REVISION_120A));
1323 }
1324
1325 static void dwc3_check_params(struct dwc3 *dwc)
1326 {
1327         struct device *dev = dwc->dev;
1328
1329         /* Check for proper value of imod_interval */
1330         if (dwc->imod_interval && !dwc3_has_imod(dwc)) {
1331                 dev_warn(dwc->dev, "Interrupt moderation not supported\n");
1332                 dwc->imod_interval = 0;
1333         }
1334
1335         /*
1336          * Workaround for STAR 9000961433 which affects only version
1337          * 3.00a of the DWC_usb3 core. This prevents the controller
1338          * interrupt from being masked while handling events. IMOD
1339          * allows us to work around this issue. Enable it for the
1340          * affected version.
1341          */
1342         if (!dwc->imod_interval &&
1343             (dwc->revision == DWC3_REVISION_300A))
1344                 dwc->imod_interval = 1;
1345
1346         /* Check the maximum_speed parameter */
1347         switch (dwc->maximum_speed) {
1348         case USB_SPEED_LOW:
1349         case USB_SPEED_FULL:
1350         case USB_SPEED_HIGH:
1351         case USB_SPEED_SUPER:
1352         case USB_SPEED_SUPER_PLUS:
1353                 break;
1354         default:
1355                 dev_err(dev, "invalid maximum_speed parameter %d\n",
1356                         dwc->maximum_speed);
1357                 /* fall through */
1358         case USB_SPEED_UNKNOWN:
1359                 /* default to superspeed */
1360                 dwc->maximum_speed = USB_SPEED_SUPER;
1361
1362                 /*
1363                  * default to superspeed plus if we are capable.
1364                  */
1365                 if (dwc3_is_usb31(dwc) &&
1366                     (DWC3_GHWPARAMS3_SSPHY_IFC(dwc->hwparams.hwparams3) ==
1367                      DWC3_GHWPARAMS3_SSPHY_IFC_GEN2))
1368                         dwc->maximum_speed = USB_SPEED_SUPER_PLUS;
1369
1370                 break;
1371         }
1372 }
1373
1374 static int dwc3_probe(struct platform_device *pdev)
1375 {
1376         struct device           *dev = &pdev->dev;
1377         struct resource         *res, dwc_res;
1378         struct dwc3             *dwc;
1379
1380         int                     ret;
1381
1382         void __iomem            *regs;
1383
1384         dwc = devm_kzalloc(dev, sizeof(*dwc), GFP_KERNEL);
1385         if (!dwc)
1386                 return -ENOMEM;
1387
1388         dwc->clks = devm_kmemdup(dev, dwc3_core_clks, sizeof(dwc3_core_clks),
1389                                  GFP_KERNEL);
1390         if (!dwc->clks)
1391                 return -ENOMEM;
1392
1393         dwc->dev = dev;
1394
1395         res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
1396         if (!res) {
1397                 dev_err(dev, "missing memory resource\n");
1398                 return -ENODEV;
1399         }
1400
1401         dwc->xhci_resources[0].start = res->start;
1402         dwc->xhci_resources[0].end = dwc->xhci_resources[0].start +
1403                                         DWC3_XHCI_REGS_END;
1404         dwc->xhci_resources[0].flags = res->flags;
1405         dwc->xhci_resources[0].name = res->name;
1406
1407         /*
1408          * Request memory region but exclude xHCI regs,
1409          * since it will be requested by the xhci-plat driver.
1410          */
1411         dwc_res = *res;
1412         dwc_res.start += DWC3_GLOBALS_REGS_START;
1413
1414         regs = devm_ioremap_resource(dev, &dwc_res);
1415         if (IS_ERR(regs))
1416                 return PTR_ERR(regs);
1417
1418         dwc->regs       = regs;
1419         dwc->regs_size  = resource_size(&dwc_res);
1420
1421         dwc3_get_properties(dwc);
1422
1423         dwc->reset = devm_reset_control_get_optional_shared(dev, NULL);
1424         if (IS_ERR(dwc->reset))
1425                 return PTR_ERR(dwc->reset);
1426
1427         if (dev->of_node) {
1428                 dwc->num_clks = ARRAY_SIZE(dwc3_core_clks);
1429
1430                 ret = clk_bulk_get(dev, dwc->num_clks, dwc->clks);
1431                 if (ret == -EPROBE_DEFER)
1432                         return ret;
1433                 /*
1434                  * Clocks are optional, but new DT platforms should support all
1435                  * clocks as required by the DT-binding.
1436                  */
1437                 if (ret)
1438                         dwc->num_clks = 0;
1439         }
1440
1441         ret = reset_control_deassert(dwc->reset);
1442         if (ret)
1443                 goto put_clks;
1444
1445         ret = clk_bulk_prepare(dwc->num_clks, dwc->clks);
1446         if (ret)
1447                 goto assert_reset;
1448
1449         ret = clk_bulk_enable(dwc->num_clks, dwc->clks);
1450         if (ret)
1451                 goto unprepare_clks;
1452
1453         platform_set_drvdata(pdev, dwc);
1454         dwc3_cache_hwparams(dwc);
1455
1456         spin_lock_init(&dwc->lock);
1457
1458         pm_runtime_set_active(dev);
1459         pm_runtime_use_autosuspend(dev);
1460         pm_runtime_set_autosuspend_delay(dev, DWC3_DEFAULT_AUTOSUSPEND_DELAY);
1461         pm_runtime_enable(dev);
1462         ret = pm_runtime_get_sync(dev);
1463         if (ret < 0)
1464                 goto err1;
1465
1466         pm_runtime_forbid(dev);
1467
1468         ret = dwc3_alloc_event_buffers(dwc, DWC3_EVENT_BUFFERS_SIZE);
1469         if (ret) {
1470                 dev_err(dwc->dev, "failed to allocate event buffers\n");
1471                 ret = -ENOMEM;
1472                 goto err2;
1473         }
1474
1475         ret = dwc3_get_dr_mode(dwc);
1476         if (ret)
1477                 goto err3;
1478
1479         ret = dwc3_alloc_scratch_buffers(dwc);
1480         if (ret)
1481                 goto err3;
1482
1483         ret = dwc3_core_init(dwc);
1484         if (ret) {
1485                 dev_err(dev, "failed to initialize core\n");
1486                 goto err4;
1487         }
1488
1489         dwc3_check_params(dwc);
1490
1491         ret = dwc3_core_init_mode(dwc);
1492         if (ret)
1493                 goto err5;
1494
1495         dwc3_debugfs_init(dwc);
1496         pm_runtime_put(dev);
1497
1498         return 0;
1499
1500 err5:
1501         dwc3_event_buffers_cleanup(dwc);
1502         dwc3_ulpi_exit(dwc);
1503
1504 err4:
1505         dwc3_free_scratch_buffers(dwc);
1506
1507 err3:
1508         dwc3_free_event_buffers(dwc);
1509
1510 err2:
1511         pm_runtime_allow(&pdev->dev);
1512
1513 err1:
1514         pm_runtime_put_sync(&pdev->dev);
1515         pm_runtime_disable(&pdev->dev);
1516
1517         clk_bulk_disable(dwc->num_clks, dwc->clks);
1518 unprepare_clks:
1519         clk_bulk_unprepare(dwc->num_clks, dwc->clks);
1520 assert_reset:
1521         reset_control_assert(dwc->reset);
1522 put_clks:
1523         clk_bulk_put(dwc->num_clks, dwc->clks);
1524
1525         return ret;
1526 }
1527
1528 static int dwc3_remove(struct platform_device *pdev)
1529 {
1530         struct dwc3     *dwc = platform_get_drvdata(pdev);
1531
1532         pm_runtime_get_sync(&pdev->dev);
1533
1534         dwc3_debugfs_exit(dwc);
1535         dwc3_core_exit_mode(dwc);
1536
1537         dwc3_core_exit(dwc);
1538         dwc3_ulpi_exit(dwc);
1539
1540         pm_runtime_put_sync(&pdev->dev);
1541         pm_runtime_allow(&pdev->dev);
1542         pm_runtime_disable(&pdev->dev);
1543
1544         dwc3_free_event_buffers(dwc);
1545         dwc3_free_scratch_buffers(dwc);
1546         clk_bulk_put(dwc->num_clks, dwc->clks);
1547
1548         return 0;
1549 }
1550
1551 #ifdef CONFIG_PM
1552 static int dwc3_core_init_for_resume(struct dwc3 *dwc)
1553 {
1554         int ret;
1555
1556         ret = reset_control_deassert(dwc->reset);
1557         if (ret)
1558                 return ret;
1559
1560         ret = clk_bulk_prepare(dwc->num_clks, dwc->clks);
1561         if (ret)
1562                 goto assert_reset;
1563
1564         ret = clk_bulk_enable(dwc->num_clks, dwc->clks);
1565         if (ret)
1566                 goto unprepare_clks;
1567
1568         ret = dwc3_core_init(dwc);
1569         if (ret)
1570                 goto disable_clks;
1571
1572         return 0;
1573
1574 disable_clks:
1575         clk_bulk_disable(dwc->num_clks, dwc->clks);
1576 unprepare_clks:
1577         clk_bulk_unprepare(dwc->num_clks, dwc->clks);
1578 assert_reset:
1579         reset_control_assert(dwc->reset);
1580
1581         return ret;
1582 }
1583
1584 static int dwc3_suspend_common(struct dwc3 *dwc, pm_message_t msg)
1585 {
1586         unsigned long   flags;
1587         u32 reg;
1588
1589         switch (dwc->current_dr_role) {
1590         case DWC3_GCTL_PRTCAP_DEVICE:
1591                 spin_lock_irqsave(&dwc->lock, flags);
1592                 dwc3_gadget_suspend(dwc);
1593                 spin_unlock_irqrestore(&dwc->lock, flags);
1594                 dwc3_core_exit(dwc);
1595                 break;
1596         case DWC3_GCTL_PRTCAP_HOST:
1597                 if (!PMSG_IS_AUTO(msg)) {
1598                         dwc3_core_exit(dwc);
1599                         break;
1600                 }
1601
1602                 /* Let controller to suspend HSPHY before PHY driver suspends */
1603                 if (dwc->dis_u2_susphy_quirk ||
1604                     dwc->dis_enblslpm_quirk) {
1605                         reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0));
1606                         reg |=  DWC3_GUSB2PHYCFG_ENBLSLPM |
1607                                 DWC3_GUSB2PHYCFG_SUSPHY;
1608                         dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg);
1609
1610                         /* Give some time for USB2 PHY to suspend */
1611                         usleep_range(5000, 6000);
1612                 }
1613
1614                 phy_pm_runtime_put_sync(dwc->usb2_generic_phy);
1615                 phy_pm_runtime_put_sync(dwc->usb3_generic_phy);
1616                 break;
1617         case DWC3_GCTL_PRTCAP_OTG:
1618                 /* do nothing during runtime_suspend */
1619                 if (PMSG_IS_AUTO(msg))
1620                         break;
1621
1622                 if (dwc->current_otg_role == DWC3_OTG_ROLE_DEVICE) {
1623                         spin_lock_irqsave(&dwc->lock, flags);
1624                         dwc3_gadget_suspend(dwc);
1625                         spin_unlock_irqrestore(&dwc->lock, flags);
1626                 }
1627
1628                 dwc3_otg_exit(dwc);
1629                 dwc3_core_exit(dwc);
1630                 break;
1631         default:
1632                 /* do nothing */
1633                 break;
1634         }
1635
1636         return 0;
1637 }
1638
1639 static int dwc3_resume_common(struct dwc3 *dwc, pm_message_t msg)
1640 {
1641         unsigned long   flags;
1642         int             ret;
1643         u32             reg;
1644
1645         switch (dwc->current_dr_role) {
1646         case DWC3_GCTL_PRTCAP_DEVICE:
1647                 ret = dwc3_core_init_for_resume(dwc);
1648                 if (ret)
1649                         return ret;
1650
1651                 dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_DEVICE);
1652                 spin_lock_irqsave(&dwc->lock, flags);
1653                 dwc3_gadget_resume(dwc);
1654                 spin_unlock_irqrestore(&dwc->lock, flags);
1655                 break;
1656         case DWC3_GCTL_PRTCAP_HOST:
1657                 if (!PMSG_IS_AUTO(msg)) {
1658                         ret = dwc3_core_init_for_resume(dwc);
1659                         if (ret)
1660                                 return ret;
1661                         dwc3_set_prtcap(dwc, DWC3_GCTL_PRTCAP_HOST);
1662                         break;
1663                 }
1664                 /* Restore GUSB2PHYCFG bits that were modified in suspend */
1665                 reg = dwc3_readl(dwc->regs, DWC3_GUSB2PHYCFG(0));
1666                 if (dwc->dis_u2_susphy_quirk)
1667                         reg &= ~DWC3_GUSB2PHYCFG_SUSPHY;
1668
1669                 if (dwc->dis_enblslpm_quirk)
1670                         reg &= ~DWC3_GUSB2PHYCFG_ENBLSLPM;
1671
1672                 dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg);
1673
1674                 phy_pm_runtime_get_sync(dwc->usb2_generic_phy);
1675                 phy_pm_runtime_get_sync(dwc->usb3_generic_phy);
1676                 break;
1677         case DWC3_GCTL_PRTCAP_OTG:
1678                 /* nothing to do on runtime_resume */
1679                 if (PMSG_IS_AUTO(msg))
1680                         break;
1681
1682                 ret = dwc3_core_init(dwc);
1683                 if (ret)
1684                         return ret;
1685
1686                 dwc3_set_prtcap(dwc, dwc->current_dr_role);
1687
1688                 dwc3_otg_init(dwc);
1689                 if (dwc->current_otg_role == DWC3_OTG_ROLE_HOST) {
1690                         dwc3_otg_host_init(dwc);
1691                 } else if (dwc->current_otg_role == DWC3_OTG_ROLE_DEVICE) {
1692                         spin_lock_irqsave(&dwc->lock, flags);
1693                         dwc3_gadget_resume(dwc);
1694                         spin_unlock_irqrestore(&dwc->lock, flags);
1695                 }
1696
1697                 break;
1698         default:
1699                 /* do nothing */
1700                 break;
1701         }
1702
1703         return 0;
1704 }
1705
1706 static int dwc3_runtime_checks(struct dwc3 *dwc)
1707 {
1708         switch (dwc->current_dr_role) {
1709         case DWC3_GCTL_PRTCAP_DEVICE:
1710                 if (dwc->connected)
1711                         return -EBUSY;
1712                 break;
1713         case DWC3_GCTL_PRTCAP_HOST:
1714         default:
1715                 /* do nothing */
1716                 break;
1717         }
1718
1719         return 0;
1720 }
1721
1722 static int dwc3_runtime_suspend(struct device *dev)
1723 {
1724         struct dwc3     *dwc = dev_get_drvdata(dev);
1725         int             ret;
1726
1727         if (dwc3_runtime_checks(dwc))
1728                 return -EBUSY;
1729
1730         ret = dwc3_suspend_common(dwc, PMSG_AUTO_SUSPEND);
1731         if (ret)
1732                 return ret;
1733
1734         device_init_wakeup(dev, true);
1735
1736         return 0;
1737 }
1738
1739 static int dwc3_runtime_resume(struct device *dev)
1740 {
1741         struct dwc3     *dwc = dev_get_drvdata(dev);
1742         int             ret;
1743
1744         device_init_wakeup(dev, false);
1745
1746         ret = dwc3_resume_common(dwc, PMSG_AUTO_RESUME);
1747         if (ret)
1748                 return ret;
1749
1750         switch (dwc->current_dr_role) {
1751         case DWC3_GCTL_PRTCAP_DEVICE:
1752                 dwc3_gadget_process_pending_events(dwc);
1753                 break;
1754         case DWC3_GCTL_PRTCAP_HOST:
1755         default:
1756                 /* do nothing */
1757                 break;
1758         }
1759
1760         pm_runtime_mark_last_busy(dev);
1761
1762         return 0;
1763 }
1764
1765 static int dwc3_runtime_idle(struct device *dev)
1766 {
1767         struct dwc3     *dwc = dev_get_drvdata(dev);
1768
1769         switch (dwc->current_dr_role) {
1770         case DWC3_GCTL_PRTCAP_DEVICE:
1771                 if (dwc3_runtime_checks(dwc))
1772                         return -EBUSY;
1773                 break;
1774         case DWC3_GCTL_PRTCAP_HOST:
1775         default:
1776                 /* do nothing */
1777                 break;
1778         }
1779
1780         pm_runtime_mark_last_busy(dev);
1781         pm_runtime_autosuspend(dev);
1782
1783         return 0;
1784 }
1785 #endif /* CONFIG_PM */
1786
1787 #ifdef CONFIG_PM_SLEEP
1788 static int dwc3_suspend(struct device *dev)
1789 {
1790         struct dwc3     *dwc = dev_get_drvdata(dev);
1791         int             ret;
1792
1793         ret = dwc3_suspend_common(dwc, PMSG_SUSPEND);
1794         if (ret)
1795                 return ret;
1796
1797         pinctrl_pm_select_sleep_state(dev);
1798
1799         return 0;
1800 }
1801
1802 static int dwc3_resume(struct device *dev)
1803 {
1804         struct dwc3     *dwc = dev_get_drvdata(dev);
1805         int             ret;
1806
1807         pinctrl_pm_select_default_state(dev);
1808
1809         ret = dwc3_resume_common(dwc, PMSG_RESUME);
1810         if (ret)
1811                 return ret;
1812
1813         pm_runtime_disable(dev);
1814         pm_runtime_set_active(dev);
1815         pm_runtime_enable(dev);
1816
1817         return 0;
1818 }
1819 #endif /* CONFIG_PM_SLEEP */
1820
1821 static const struct dev_pm_ops dwc3_dev_pm_ops = {
1822         SET_SYSTEM_SLEEP_PM_OPS(dwc3_suspend, dwc3_resume)
1823         SET_RUNTIME_PM_OPS(dwc3_runtime_suspend, dwc3_runtime_resume,
1824                         dwc3_runtime_idle)
1825 };
1826
1827 #ifdef CONFIG_OF
1828 static const struct of_device_id of_dwc3_match[] = {
1829         {
1830                 .compatible = "snps,dwc3"
1831         },
1832         {
1833                 .compatible = "synopsys,dwc3"
1834         },
1835         { },
1836 };
1837 MODULE_DEVICE_TABLE(of, of_dwc3_match);
1838 #endif
1839
1840 #ifdef CONFIG_ACPI
1841
1842 #define ACPI_ID_INTEL_BSW       "808622B7"
1843
1844 static const struct acpi_device_id dwc3_acpi_match[] = {
1845         { ACPI_ID_INTEL_BSW, 0 },
1846         { },
1847 };
1848 MODULE_DEVICE_TABLE(acpi, dwc3_acpi_match);
1849 #endif
1850
1851 static struct platform_driver dwc3_driver = {
1852         .probe          = dwc3_probe,
1853         .remove         = dwc3_remove,
1854         .driver         = {
1855                 .name   = "dwc3",
1856                 .of_match_table = of_match_ptr(of_dwc3_match),
1857                 .acpi_match_table = ACPI_PTR(dwc3_acpi_match),
1858                 .pm     = &dwc3_dev_pm_ops,
1859         },
1860 };
1861
1862 module_platform_driver(dwc3_driver);
1863
1864 MODULE_ALIAS("platform:dwc3");
1865 MODULE_AUTHOR("Felipe Balbi <balbi@ti.com>");
1866 MODULE_LICENSE("GPL v2");
1867 MODULE_DESCRIPTION("DesignWare USB3 DRD Controller Driver");