drivers/sbus/char/bbc_envctrl.c

   1 /* $Id: bbc_envctrl.c,v 1.4 2001/04/06 16:48:08 davem Exp $
   2  * bbc_envctrl.c: UltraSPARC-III environment control driver.
   3  *
   4  * Copyright (C) 2001 David S. Miller (davem@redhat.com)
   5  */
   6
   7 #include <linux/kernel.h>
   8 #include <linux/kthread.h>
   9 #include <linux/sched.h>
  10 #include <linux/slab.h>
  11 #include <linux/delay.h>
  12 #include <asm/oplib.h>
  13 #include <asm/ebus.h>
  14
  15 #include "bbc_i2c.h"
  16 #include "max1617.h"
  17
  18 #undef ENVCTRL_TRACE
  19
  20 /* WARNING: Making changes to this driver is very dangerous.
  21  *          If you misprogram the sensor chips they can
  22  *          cut the power on you instantly.
  23  */
  24
  25 /* Two temperature sensors exist in the SunBLADE-1000 enclosure.
  26  * Both are implemented using max1617 i2c devices.  Each max1617
  27  * monitors 2 temperatures, one for one of the cpu dies and the other
  28  * for the ambient temperature.
  29  *
  30  * The max1617 is capable of being programmed with power-off
  31  * temperature values, one low limit and one high limit.  These
  32  * can be controlled independently for the cpu or ambient temperature.
  33  * If a limit is violated, the power is simply shut off.  The frequency
  34  * with which the max1617 does temperature sampling can be controlled
  35  * as well.
  36  *
  37  * Three fans exist inside the machine, all three are controlled with
  38  * an i2c digital to analog converter.  There is a fan directed at the
  39  * two processor slots, another for the rest of the enclosure, and the
  40  * third is for the power supply.  The first two fans may be speed
  41  * controlled by changing the voltage fed to them.  The third fan may
  42  * only be completely off or on.  The third fan is meant to only be
  43  * disabled/enabled when entering/exiting the lowest power-saving
  44  * mode of the machine.
  45  *
  46  * An environmental control kernel thread periodically monitors all
  47  * temperature sensors.  Based upon the samples it will adjust the
  48  * fan speeds to try and keep the system within a certain temperature
  49  * range (the goal being to make the fans as quiet as possible without
  50  * allowing the system to get too hot).
  51  *
  52  * If the temperature begins to rise/fall outside of the acceptable
  53  * operating range, a periodic warning will be sent to the kernel log.
  54  * The fans will be put on full blast to attempt to deal with this
  55  * situation.  After exceeding the acceptable operating range by a
  56  * certain threshold, the kernel thread will shut down the system.
  57  * Here, the thread is attempting to shut the machine down cleanly
  58  * before the hardware based power-off event is triggered.
  59  */
  60
  61 /* These settings are in Celsius.  We use these defaults only
  62  * if we cannot interrogate the cpu-fru SEEPROM.
  63  */
  64 struct temp_limits {
  65         s8 high_pwroff, high_shutdown, high_warn;
  66         s8 low_warn, low_shutdown, low_pwroff;
  67 };
  68
  69 static struct temp_limits cpu_temp_limits[2] = {
  70         { 100, 85, 80, 5, -5, -10 },
  71         { 100, 85, 80, 5, -5, -10 },
  72 };
  73
  74 static struct temp_limits amb_temp_limits[2] = {
  75         { 65, 55, 40, 5, -5, -10 },
  76         { 65, 55, 40, 5, -5, -10 },
  77 };
  78
  79 enum fan_action { FAN_SLOWER, FAN_SAME, FAN_FASTER, FAN_FULLBLAST, FAN_STATE_MAX };
  80
  81 struct bbc_cpu_temperature {
  82         struct bbc_cpu_temperature      *next;
  83
  84         struct bbc_i2c_client           *client;
  85         int                             index;
  86
  87         /* Current readings, and history. */
  88         s8                              curr_cpu_temp;
  89         s8                              curr_amb_temp;
  90         s8                              prev_cpu_temp;
  91         s8                              prev_amb_temp;
  92         s8                              avg_cpu_temp;
  93         s8                              avg_amb_temp;
  94
  95         int                             sample_tick;
  96
  97         enum fan_action                 fan_todo[2];
  98 #define FAN_AMBIENT     0
  99 #define FAN_CPU         1
 100 };
 101
 102 struct bbc_cpu_temperature *all_bbc_temps;
 103
 104 struct bbc_fan_control {
 105         struct bbc_fan_control  *next;
 106
 107         struct bbc_i2c_client   *client;
 108         int                     index;
 109
 110         int                     psupply_fan_on;
 111         int                     cpu_fan_speed;
 112         int                     system_fan_speed;
 113 };
 114
 115 struct bbc_fan_control *all_bbc_fans;
 116
 117 #define CPU_FAN_REG     0xf0
 118 #define SYS_FAN_REG     0xf2
 119 #define PSUPPLY_FAN_REG 0xf4
 120
 121 #define FAN_SPEED_MIN   0x0c
 122 #define FAN_SPEED_MAX   0x3f
 123
 124 #define PSUPPLY_FAN_ON  0x1f
 125 #define PSUPPLY_FAN_OFF 0x00
 126
 127 static void set_fan_speeds(struct bbc_fan_control *fp)
 128 {
 129         /* Put temperatures into range so we don't mis-program
 130          * the hardware.
 131          */
 132         if (fp->cpu_fan_speed < FAN_SPEED_MIN)
 133                 fp->cpu_fan_speed = FAN_SPEED_MIN;
 134         if (fp->cpu_fan_speed > FAN_SPEED_MAX)
 135                 fp->cpu_fan_speed = FAN_SPEED_MAX;
 136         if (fp->system_fan_speed < FAN_SPEED_MIN)
 137                 fp->system_fan_speed = FAN_SPEED_MIN;
 138         if (fp->system_fan_speed > FAN_SPEED_MAX)
 139                 fp->system_fan_speed = FAN_SPEED_MAX;
 140 #ifdef ENVCTRL_TRACE
 141         printk("fan%d: Changed fan speed to cpu(%02x) sys(%02x)\n",
 142                fp->index,
 143                fp->cpu_fan_speed, fp->system_fan_speed);
 144 #endif
 145
 146         bbc_i2c_writeb(fp->client, fp->cpu_fan_speed, CPU_FAN_REG);
 147         bbc_i2c_writeb(fp->client, fp->system_fan_speed, SYS_FAN_REG);
 148         bbc_i2c_writeb(fp->client,
 149                        (fp->psupply_fan_on ?
 150                         PSUPPLY_FAN_ON : PSUPPLY_FAN_OFF),
 151                        PSUPPLY_FAN_REG);
 152 }
 153
 154 static void get_current_temps(struct bbc_cpu_temperature *tp)
 155 {
 156         tp->prev_amb_temp = tp->curr_amb_temp;
 157         bbc_i2c_readb(tp->client,
 158                       (unsigned char *) &tp->curr_amb_temp,
 159                       MAX1617_AMB_TEMP);
 160         tp->prev_cpu_temp = tp->curr_cpu_temp;
 161         bbc_i2c_readb(tp->client,
 162                       (unsigned char *) &tp->curr_cpu_temp,
 163                       MAX1617_CPU_TEMP);
 164 #ifdef ENVCTRL_TRACE
 165         printk("temp%d: cpu(%d C) amb(%d C)\n",
 166                tp->index,
 167                (int) tp->curr_cpu_temp, (int) tp->curr_amb_temp);
 168 #endif
 169 }
 170
 171
 172 static void do_envctrl_shutdown(struct bbc_cpu_temperature *tp)
 173 {
 174         static int shutting_down = 0;
 175         static char *envp[] = { "HOME=/", "TERM=linux", "PATH=/sbin:/usr/sbin:/bin:/usr/bin", NULL };
 176         char *argv[] = { "/sbin/shutdown", "-h", "now", NULL };
 177         char *type = "???";
 178         s8 val = -1;
 179
 180         if (shutting_down != 0)
 181                 return;
 182
 183         if (tp->curr_amb_temp >= amb_temp_limits[tp->index].high_shutdown ||
 184             tp->curr_amb_temp < amb_temp_limits[tp->index].low_shutdown) {
 185                 type = "ambient";
 186                 val = tp->curr_amb_temp;
 187         } else if (tp->curr_cpu_temp >= cpu_temp_limits[tp->index].high_shutdown ||
 188                    tp->curr_cpu_temp < cpu_temp_limits[tp->index].low_shutdown) {
 189                 type = "CPU";
 190                 val = tp->curr_cpu_temp;
 191         }
 192
 193         printk(KERN_CRIT "temp%d: Outside of safe %s "
 194                "operating temperature, %d C.\n",
 195                tp->index, type, val);
 196
 197         printk(KERN_CRIT "kenvctrld: Shutting down the system now.\n");
 198
 199         shutting_down = 1;
 200         if (kernel_execve("/sbin/shutdown", argv, envp) < 0)
 201                 printk(KERN_CRIT "envctrl: shutdown execution failed\n");
 202 }
 203
 204 #define WARN_INTERVAL   (30 * HZ)
 205
 206 static void analyze_ambient_temp(struct bbc_cpu_temperature *tp, unsigned long *last_warn, int tick)
 207 {
 208         int ret = 0;
 209
 210         if (time_after(jiffies, (*last_warn + WARN_INTERVAL))) {
 211                 if (tp->curr_amb_temp >=
 212                     amb_temp_limits[tp->index].high_warn) {
 213                         printk(KERN_WARNING "temp%d: "
 214                                "Above safe ambient operating temperature, %d C.\n",
 215                                tp->index, (int) tp->curr_amb_temp);
 216                         ret = 1;
 217                 } else if (tp->curr_amb_temp <
 218                            amb_temp_limits[tp->index].low_warn) {
 219                         printk(KERN_WARNING "temp%d: "
 220                                "Below safe ambient operating temperature, %d C.\n",
 221                                tp->index, (int) tp->curr_amb_temp);
 222                         ret = 1;
 223                 }
 224                 if (ret)
 225                         *last_warn = jiffies;
 226         } else if (tp->curr_amb_temp >= amb_temp_limits[tp->index].high_warn ||
 227                    tp->curr_amb_temp < amb_temp_limits[tp->index].low_warn)
 228                 ret = 1;
 229
 230         /* Now check the shutdown limits. */
 231         if (tp->curr_amb_temp >= amb_temp_limits[tp->index].high_shutdown ||
 232             tp->curr_amb_temp < amb_temp_limits[tp->index].low_shutdown) {
 233                 do_envctrl_shutdown(tp);
 234                 ret = 1;
 235         }
 236
 237         if (ret) {
 238                 tp->fan_todo[FAN_AMBIENT] = FAN_FULLBLAST;
 239         } else if ((tick & (8 - 1)) == 0) {
 240                 s8 amb_goal_hi = amb_temp_limits[tp->index].high_warn - 10;
 241                 s8 amb_goal_lo;
 242
 243                 amb_goal_lo = amb_goal_hi - 3;
 244
 245                 /* We do not try to avoid 'too cold' events.  Basically we
 246                  * only try to deal with over-heating and fan noise reduction.
 247                  */
 248                 if (tp->avg_amb_temp < amb_goal_hi) {
 249                         if (tp->avg_amb_temp >= amb_goal_lo)
 250                                 tp->fan_todo[FAN_AMBIENT] = FAN_SAME;
 251                         else
 252                                 tp->fan_todo[FAN_AMBIENT] = FAN_SLOWER;
 253                 } else {
 254                         tp->fan_todo[FAN_AMBIENT] = FAN_FASTER;
 255                 }
 256         } else {
 257                 tp->fan_todo[FAN_AMBIENT] = FAN_SAME;
 258         }
 259 }
 260
 261 static void analyze_cpu_temp(struct bbc_cpu_temperature *tp, unsigned long *last_warn, int tick)
 262 {
 263         int ret = 0;
 264
 265         if (time_after(jiffies, (*last_warn + WARN_INTERVAL))) {
 266                 if (tp->curr_cpu_temp >=
 267                     cpu_temp_limits[tp->index].high_warn) {
 268                         printk(KERN_WARNING "temp%d: "
 269                                "Above safe CPU operating temperature, %d C.\n",
 270                                tp->index, (int) tp->curr_cpu_temp);
 271                         ret = 1;
 272                 } else if (tp->curr_cpu_temp <
 273                            cpu_temp_limits[tp->index].low_warn) {
 274                         printk(KERN_WARNING "temp%d: "
 275                                "Below safe CPU operating temperature, %d C.\n",
 276                                tp->index, (int) tp->curr_cpu_temp);
 277                         ret = 1;
 278                 }
 279                 if (ret)
 280                         *last_warn = jiffies;
 281         } else if (tp->curr_cpu_temp >= cpu_temp_limits[tp->index].high_warn ||
 282                    tp->curr_cpu_temp < cpu_temp_limits[tp->index].low_warn)
 283                 ret = 1;
 284
 285         /* Now check the shutdown limits. */
 286         if (tp->curr_cpu_temp >= cpu_temp_limits[tp->index].high_shutdown ||
 287             tp->curr_cpu_temp < cpu_temp_limits[tp->index].low_shutdown) {
 288                 do_envctrl_shutdown(tp);
 289                 ret = 1;
 290         }
 291
 292         if (ret) {
 293                 tp->fan_todo[FAN_CPU] = FAN_FULLBLAST;
 294         } else if ((tick & (8 - 1)) == 0) {
 295                 s8 cpu_goal_hi = cpu_temp_limits[tp->index].high_warn - 10;
 296                 s8 cpu_goal_lo;
 297
 298                 cpu_goal_lo = cpu_goal_hi - 3;
 299
 300                 /* We do not try to avoid 'too cold' events.  Basically we
 301                  * only try to deal with over-heating and fan noise reduction.
 302                  */
 303                 if (tp->avg_cpu_temp < cpu_goal_hi) {
 304                         if (tp->avg_cpu_temp >= cpu_goal_lo)
 305                                 tp->fan_todo[FAN_CPU] = FAN_SAME;
 306                         else
 307                                 tp->fan_todo[FAN_CPU] = FAN_SLOWER;
 308                 } else {
 309                         tp->fan_todo[FAN_CPU] = FAN_FASTER;
 310                 }
 311         } else {
 312                 tp->fan_todo[FAN_CPU] = FAN_SAME;
 313         }
 314 }
 315
 316 static void analyze_temps(struct bbc_cpu_temperature *tp, unsigned long *last_warn)
 317 {
 318         tp->avg_amb_temp = (s8)((int)((int)tp->avg_amb_temp + (int)tp->curr_amb_temp) / 2);
 319         tp->avg_cpu_temp = (s8)((int)((int)tp->avg_cpu_temp + (int)tp->curr_cpu_temp) / 2);
 320
 321         analyze_ambient_temp(tp, last_warn, tp->sample_tick);
 322         analyze_cpu_temp(tp, last_warn, tp->sample_tick);
 323
 324         tp->sample_tick++;
 325 }
 326
 327 static enum fan_action prioritize_fan_action(int which_fan)
 328 {
 329         struct bbc_cpu_temperature *tp;
 330         enum fan_action decision = FAN_STATE_MAX;
 331
 332         /* Basically, prioritize what the temperature sensors
 333          * recommend we do, and perform that action on all the
 334          * fans.
 335          */
 336         for (tp = all_bbc_temps; tp; tp = tp->next) {
 337                 if (tp->fan_todo[which_fan] == FAN_FULLBLAST) {
 338                         decision = FAN_FULLBLAST;
 339                         break;
 340                 }
 341                 if (tp->fan_todo[which_fan] == FAN_SAME &&
 342                     decision != FAN_FASTER)
 343                         decision = FAN_SAME;
 344                 else if (tp->fan_todo[which_fan] == FAN_FASTER)
 345                         decision = FAN_FASTER;
 346                 else if (decision != FAN_FASTER &&
 347                          decision != FAN_SAME &&
 348                          tp->fan_todo[which_fan] == FAN_SLOWER)
 349                         decision = FAN_SLOWER;
 350         }
 351         if (decision == FAN_STATE_MAX)
 352                 decision = FAN_SAME;
 353
 354         return decision;
 355 }
 356
 357 static int maybe_new_ambient_fan_speed(struct bbc_fan_control *fp)
 358 {
 359         enum fan_action decision = prioritize_fan_action(FAN_AMBIENT);
 360         int ret;
 361
 362         if (decision == FAN_SAME)
 363                 return 0;
 364
 365         ret = 1;
 366         if (decision == FAN_FULLBLAST) {
 367                 if (fp->system_fan_speed >= FAN_SPEED_MAX)
 368                         ret = 0;
 369                 else
 370                         fp->system_fan_speed = FAN_SPEED_MAX;
 371         } else {
 372                 if (decision == FAN_FASTER) {
 373                         if (fp->system_fan_speed >= FAN_SPEED_MAX)
 374                                 ret = 0;
 375                         else
 376                                 fp->system_fan_speed += 2;
 377                 } else {
 378                         int orig_speed = fp->system_fan_speed;
 379
 380                         if (orig_speed <= FAN_SPEED_MIN ||
 381                             orig_speed <= (fp->cpu_fan_speed - 3))
 382                                 ret = 0;
 383                         else
 384                                 fp->system_fan_speed -= 1;
 385                 }
 386         }
 387
 388         return ret;
 389 }
 390
 391 static int maybe_new_cpu_fan_speed(struct bbc_fan_control *fp)
 392 {
 393         enum fan_action decision = prioritize_fan_action(FAN_CPU);
 394         int ret;
 395
 396         if (decision == FAN_SAME)
 397                 return 0;
 398
 399         ret = 1;
 400         if (decision == FAN_FULLBLAST) {
 401                 if (fp->cpu_fan_speed >= FAN_SPEED_MAX)
 402                         ret = 0;
 403                 else
 404                         fp->cpu_fan_speed = FAN_SPEED_MAX;
 405         } else {
 406                 if (decision == FAN_FASTER) {
 407                         if (fp->cpu_fan_speed >= FAN_SPEED_MAX)
 408                                 ret = 0;
 409                         else {
 410                                 fp->cpu_fan_speed += 2;
 411                                 if (fp->system_fan_speed <
 412                                     (fp->cpu_fan_speed - 3))
 413                                         fp->system_fan_speed =
 414                                                 fp->cpu_fan_speed - 3;
 415                         }
 416                 } else {
 417                         if (fp->cpu_fan_speed <= FAN_SPEED_MIN)
 418                                 ret = 0;
 419                         else
 420                                 fp->cpu_fan_speed -= 1;
 421                 }
 422         }
 423
 424         return ret;
 425 }
 426
 427 static void maybe_new_fan_speeds(struct bbc_fan_control *fp)
 428 {
 429         int new;
 430
 431         new  = maybe_new_ambient_fan_speed(fp);
 432         new |= maybe_new_cpu_fan_speed(fp);
 433
 434         if (new)
 435                 set_fan_speeds(fp);
 436 }
 437
 438 static void fans_full_blast(void)
 439 {
 440         struct bbc_fan_control *fp;
 441
 442         /* Since we will not be monitoring things anymore, put
 443          * the fans on full blast.
 444          */
 445         for (fp = all_bbc_fans; fp; fp = fp->next) {
 446                 fp->cpu_fan_speed = FAN_SPEED_MAX;
 447                 fp->system_fan_speed = FAN_SPEED_MAX;
 448                 fp->psupply_fan_on = 1;
 449                 set_fan_speeds(fp);
 450         }
 451 }
 452
 453 #define POLL_INTERVAL   (5 * 1000)
 454 static unsigned long last_warning_jiffies;
 455 static struct task_struct *kenvctrld_task;
 456
 457 static int kenvctrld(void *__unused)
 458 {
 459         printk(KERN_INFO "bbc_envctrl: kenvctrld starting...\n");
 460         last_warning_jiffies = jiffies - WARN_INTERVAL;
 461         for (;;) {
 462                 struct bbc_cpu_temperature *tp;
 463                 struct bbc_fan_control *fp;
 464
 465                 msleep_interruptible(POLL_INTERVAL);
 466                 if (kthread_should_stop())
 467                         break;
 468
 469                 for (tp = all_bbc_temps; tp; tp = tp->next) {
 470                         get_current_temps(tp);
 471                         analyze_temps(tp, &last_warning_jiffies);
 472                 }
 473                 for (fp = all_bbc_fans; fp; fp = fp->next)
 474                         maybe_new_fan_speeds(fp);
 475         }
 476         printk(KERN_INFO "bbc_envctrl: kenvctrld exiting...\n");
 477
 478         fans_full_blast();
 479
 480         return 0;
 481 }
 482
 483 static void attach_one_temp(struct linux_ebus_child *echild, int temp_idx)
 484 {
 485         struct bbc_cpu_temperature *tp = kmalloc(sizeof(*tp), GFP_KERNEL);
 486
 487         if (!tp)
 488                 return;
 489         memset(tp, 0, sizeof(*tp));
 490         tp->client = bbc_i2c_attach(echild);
 491         if (!tp->client) {
 492                 kfree(tp);
 493                 return;
 494         }
 495
 496         tp->index = temp_idx;
 497         {
 498                 struct bbc_cpu_temperature **tpp = &all_bbc_temps;
 499                 while (*tpp)
 500                         tpp = &((*tpp)->next);
 501                 tp->next = NULL;
 502                 *tpp = tp;
 503         }
 504
 505         /* Tell it to convert once every 5 seconds, clear all cfg
 506          * bits.
 507          */
 508         bbc_i2c_writeb(tp->client, 0x00, MAX1617_WR_CFG_BYTE);
 509         bbc_i2c_writeb(tp->client, 0x02, MAX1617_WR_CVRATE_BYTE);
 510
 511         /* Program the hard temperature limits into the chip. */
 512         bbc_i2c_writeb(tp->client, amb_temp_limits[tp->index].high_pwroff,
 513                        MAX1617_WR_AMB_HIGHLIM);
 514         bbc_i2c_writeb(tp->client, amb_temp_limits[tp->index].low_pwroff,
 515                        MAX1617_WR_AMB_LOWLIM);
 516         bbc_i2c_writeb(tp->client, cpu_temp_limits[tp->index].high_pwroff,
 517                        MAX1617_WR_CPU_HIGHLIM);
 518         bbc_i2c_writeb(tp->client, cpu_temp_limits[tp->index].low_pwroff,
 519                        MAX1617_WR_CPU_LOWLIM);
 520
 521         get_current_temps(tp);
 522         tp->prev_cpu_temp = tp->avg_cpu_temp = tp->curr_cpu_temp;
 523         tp->prev_amb_temp = tp->avg_amb_temp = tp->curr_amb_temp;
 524
 525         tp->fan_todo[FAN_AMBIENT] = FAN_SAME;
 526         tp->fan_todo[FAN_CPU] = FAN_SAME;
 527 }
 528
 529 static void attach_one_fan(struct linux_ebus_child *echild, int fan_idx)
 530 {
 531         struct bbc_fan_control *fp = kmalloc(sizeof(*fp), GFP_KERNEL);
 532
 533         if (!fp)
 534                 return;
 535         memset(fp, 0, sizeof(*fp));
 536         fp->client = bbc_i2c_attach(echild);
 537         if (!fp->client) {
 538                 kfree(fp);
 539                 return;
 540         }
 541
 542         fp->index = fan_idx;
 543
 544         {
 545                 struct bbc_fan_control **fpp = &all_bbc_fans;
 546                 while (*fpp)
 547                         fpp = &((*fpp)->next);
 548                 fp->next = NULL;
 549                 *fpp = fp;
 550         }
 551
 552         /* The i2c device controlling the fans is write-only.
 553          * So the only way to keep track of the current power
 554          * level fed to the fans is via software.  Choose half
 555          * power for cpu/system and 'on' fo the powersupply fan
 556          * and set it now.
 557          */
 558         fp->psupply_fan_on = 1;
 559         fp->cpu_fan_speed = (FAN_SPEED_MAX - FAN_SPEED_MIN) / 2;
 560         fp->cpu_fan_speed += FAN_SPEED_MIN;
 561         fp->system_fan_speed = (FAN_SPEED_MAX - FAN_SPEED_MIN) / 2;
 562         fp->system_fan_speed += FAN_SPEED_MIN;
 563
 564         set_fan_speeds(fp);
 565 }
 566
 567 int bbc_envctrl_init(void)
 568 {
 569         struct linux_ebus_child *echild;
 570         int temp_index = 0;
 571         int fan_index = 0;
 572         int devidx = 0;
 573
 574         while ((echild = bbc_i2c_getdev(devidx++)) != NULL) {
 575                 if (!strcmp(echild->prom_node->name, "temperature"))
 576                         attach_one_temp(echild, temp_index++);
 577                 if (!strcmp(echild->prom_node->name, "fan-control"))
 578                         attach_one_fan(echild, fan_index++);
 579         }
 580         if (temp_index != 0 && fan_index != 0) {
 581                 kenvctrld_task = kthread_run(kenvctrld, NULL, "kenvctrld");
 582                 if (IS_ERR(kenvctrld_task))
 583                         return PTR_ERR(kenvctrld_task);
 584         }
 585
 586         return 0;
 587 }
 588
 589 static void destroy_one_temp(struct bbc_cpu_temperature *tp)
 590 {
 591         bbc_i2c_detach(tp->client);
 592         kfree(tp);
 593 }
 594
 595 static void destroy_one_fan(struct bbc_fan_control *fp)
 596 {
 597         bbc_i2c_detach(fp->client);
 598         kfree(fp);
 599 }
 600
 601 void bbc_envctrl_cleanup(void)
 602 {
 603         struct bbc_cpu_temperature *tp;
 604         struct bbc_fan_control *fp;
 605
 606         kthread_stop(kenvctrld_task);
 607
 608         tp = all_bbc_temps;
 609         while (tp != NULL) {
 610                 struct bbc_cpu_temperature *next = tp->next;
 611                 destroy_one_temp(tp);
 612                 tp = next;
 613         }
 614         all_bbc_temps = NULL;
 615
 616         fp = all_bbc_fans;
 617         while (fp != NULL) {
 618                 struct bbc_fan_control *next = fp->next;
 619                 destroy_one_fan(fp);
 620                 fp = next;
 621         }
 622         all_bbc_fans = NULL;
 623 }