drivers/ide/pci/hpt366.c

   1 /*
   2  * linux/drivers/ide/pci/hpt366.c               Version 0.36    April 25, 2003
   3  *
   4  * Copyright (C) 1999-2003              Andre Hedrick <andre@linux-ide.org>
   5  * Portions Copyright (C) 2001          Sun Microsystems, Inc.
   6  * Portions Copyright (C) 2003          Red Hat Inc
   7  *
   8  * Thanks to HighPoint Technologies for their assistance, and hardware.
   9  * Special Thanks to Jon Burchmore in SanDiego for the deep pockets, his
  10  * donation of an ABit BP6 mainboard, processor, and memory acellerated
  11  * development and support.
  12  *
  13  *
  14  * Highpoint have their own driver (source except for the raid part)
  15  * available from http://www.highpoint-tech.com/hpt3xx-opensource-v131.tgz
  16  * This may be useful to anyone wanting to work on the mainstream hpt IDE.
  17  *
  18  * Note that final HPT370 support was done by force extraction of GPL.
  19  *
  20  * - add function for getting/setting power status of drive
  21  * - the HPT370's state machine can get confused. reset it before each dma
  22  *   xfer to prevent that from happening.
  23  * - reset state engine whenever we get an error.
  24  * - check for busmaster state at end of dma.
  25  * - use new highpoint timings.
  26  * - detect bus speed using highpoint register.
  27  * - use pll if we don't have a clock table. added a 66MHz table that's
  28  *   just 2x the 33MHz table.
  29  * - removed turnaround. NOTE: we never want to switch between pll and
  30  *   pci clocks as the chip can glitch in those cases. the highpoint
  31  *   approved workaround slows everything down too much to be useful. in
  32  *   addition, we would have to serialize access to each chip.
  33  *      Adrian Sun <a.sun@sun.com>
  34  *
  35  * add drive timings for 66MHz PCI bus,
  36  * fix ATA Cable signal detection, fix incorrect /proc info
  37  * add /proc display for per-drive PIO/DMA/UDMA mode and
  38  * per-channel ATA-33/66 Cable detect.
  39  *      Duncan Laurie <void@sun.com>
  40  *
  41  * fixup /proc output for multiple controllers
  42  *      Tim Hockin <thockin@sun.com>
  43  *
  44  * On hpt366:
  45  * Reset the hpt366 on error, reset on dma
  46  * Fix disabling Fast Interrupt hpt366.
  47  *      Mike Waychison <crlf@sun.com>
  48  *
  49  * Added support for 372N clocking and clock switching. The 372N needs
  50  * different clocks on read/write. This requires overloading rw_disk and
  51  * other deeply crazy things. Thanks to <http://www.hoerstreich.de> for
  52  * keeping me sane.
  53  *              Alan Cox <alan@redhat.com>
  54  *
  55  */
  56
  57
  58 #include <linux/config.h>
  59 #include <linux/types.h>
  60 #include <linux/module.h>
  61 #include <linux/kernel.h>
  62 #include <linux/delay.h>
  63 #include <linux/timer.h>
  64 #include <linux/mm.h>
  65 #include <linux/ioport.h>
  66 #include <linux/blkdev.h>
  67 #include <linux/hdreg.h>
  68
  69 #include <linux/interrupt.h>
  70 #include <linux/pci.h>
  71 #include <linux/init.h>
  72 #include <linux/ide.h>
  73
  74 #include <asm/uaccess.h>
  75 #include <asm/io.h>
  76 #include <asm/irq.h>
  77
  78 /* various tuning parameters */
  79 #define HPT_RESET_STATE_ENGINE
  80 #undef HPT_DELAY_INTERRUPT
  81 #undef HPT_SERIALIZE_IO
  82
  83 static const char *quirk_drives[] = {
  84         "QUANTUM FIREBALLlct08 08",
  85         "QUANTUM FIREBALLP KA6.4",
  86         "QUANTUM FIREBALLP LM20.4",
  87         "QUANTUM FIREBALLP LM20.5",
  88         NULL
  89 };
  90
  91 static const char *bad_ata100_5[] = {
  92         "IBM-DTLA-307075",
  93         "IBM-DTLA-307060",
  94         "IBM-DTLA-307045",
  95         "IBM-DTLA-307030",
  96         "IBM-DTLA-307020",
  97         "IBM-DTLA-307015",
  98         "IBM-DTLA-305040",
  99         "IBM-DTLA-305030",
 100         "IBM-DTLA-305020",
 101         "IC35L010AVER07-0",
 102         "IC35L020AVER07-0",
 103         "IC35L030AVER07-0",
 104         "IC35L040AVER07-0",
 105         "IC35L060AVER07-0",
 106         "WDC AC310200R",
 107         NULL
 108 };
 109
 110 static const char *bad_ata66_4[] = {
 111         "IBM-DTLA-307075",
 112         "IBM-DTLA-307060",
 113         "IBM-DTLA-307045",
 114         "IBM-DTLA-307030",
 115         "IBM-DTLA-307020",
 116         "IBM-DTLA-307015",
 117         "IBM-DTLA-305040",
 118         "IBM-DTLA-305030",
 119         "IBM-DTLA-305020",
 120         "IC35L010AVER07-0",
 121         "IC35L020AVER07-0",
 122         "IC35L030AVER07-0",
 123         "IC35L040AVER07-0",
 124         "IC35L060AVER07-0",
 125         "WDC AC310200R",
 126         NULL
 127 };
 128
 129 static const char *bad_ata66_3[] = {
 130         "WDC AC310200R",
 131         NULL
 132 };
 133
 134 static const char *bad_ata33[] = {
 135         "Maxtor 92720U8", "Maxtor 92040U6", "Maxtor 91360U4", "Maxtor 91020U3", "Maxtor 90845U3", "Maxtor 90650U2",
 136         "Maxtor 91360D8", "Maxtor 91190D7", "Maxtor 91020D6", "Maxtor 90845D5", "Maxtor 90680D4", "Maxtor 90510D3", "Maxtor 90340D2",
 137         "Maxtor 91152D8", "Maxtor 91008D7", "Maxtor 90845D6", "Maxtor 90840D6", "Maxtor 90720D5", "Maxtor 90648D5", "Maxtor 90576D4",
 138         "Maxtor 90510D4",
 139         "Maxtor 90432D3", "Maxtor 90288D2", "Maxtor 90256D2",
 140         "Maxtor 91000D8", "Maxtor 90910D8", "Maxtor 90875D7", "Maxtor 90840D7", "Maxtor 90750D6", "Maxtor 90625D5", "Maxtor 90500D4",
 141         "Maxtor 91728D8", "Maxtor 91512D7", "Maxtor 91303D6", "Maxtor 91080D5", "Maxtor 90845D4", "Maxtor 90680D4", "Maxtor 90648D3", "Maxtor 90432D2",
 142         NULL
 143 };
 144
 145 struct chipset_bus_clock_list_entry {
 146         u8              xfer_speed;
 147         unsigned int    chipset_settings;
 148 };
 149
 150 /* key for bus clock timings
 151  * bit
 152  * 0:3    data_high_time. inactive time of DIOW_/DIOR_ for PIO and MW
 153  *        DMA. cycles = value + 1
 154  * 4:8    data_low_time. active time of DIOW_/DIOR_ for PIO and MW
 155  *        DMA. cycles = value + 1
 156  * 9:12   cmd_high_time. inactive time of DIOW_/DIOR_ during task file
 157  *        register access.
 158  * 13:17  cmd_low_time. active time of DIOW_/DIOR_ during task file
 159  *        register access.
 160  * 18:21  udma_cycle_time. clock freq and clock cycles for UDMA xfer.
 161  *        during task file register access.
 162  * 22:24  pre_high_time. time to initialize 1st cycle for PIO and MW DMA
 163  *        xfer.
 164  * 25:27  cmd_pre_high_time. time to initialize 1st PIO cycle for task
 165  *        register access.
 166  * 28     UDMA enable
 167  * 29     DMA enable
 168  * 30     PIO_MST enable. if set, the chip is in bus master mode during
 169  *        PIO.
 170  * 31     FIFO enable.
 171  */
 172 static struct chipset_bus_clock_list_entry forty_base_hpt366[] = {
 173         {       XFER_UDMA_4,    0x900fd943      },
 174         {       XFER_UDMA_3,    0x900ad943      },
 175         {       XFER_UDMA_2,    0x900bd943      },
 176         {       XFER_UDMA_1,    0x9008d943      },
 177         {       XFER_UDMA_0,    0x9008d943      },
 178
 179         {       XFER_MW_DMA_2,  0xa008d943      },
 180         {       XFER_MW_DMA_1,  0xa010d955      },
 181         {       XFER_MW_DMA_0,  0xa010d9fc      },
 182
 183         {       XFER_PIO_4,     0xc008d963      },
 184         {       XFER_PIO_3,     0xc010d974      },
 185         {       XFER_PIO_2,     0xc010d997      },
 186         {       XFER_PIO_1,     0xc010d9c7      },
 187         {       XFER_PIO_0,     0xc018d9d9      },
 188         {       0,              0x0120d9d9      }
 189 };
 190
 191 static struct chipset_bus_clock_list_entry thirty_three_base_hpt366[] = {
 192         {       XFER_UDMA_4,    0x90c9a731      },
 193         {       XFER_UDMA_3,    0x90cfa731      },
 194         {       XFER_UDMA_2,    0x90caa731      },
 195         {       XFER_UDMA_1,    0x90cba731      },
 196         {       XFER_UDMA_0,    0x90c8a731      },
 197
 198         {       XFER_MW_DMA_2,  0xa0c8a731      },
 199         {       XFER_MW_DMA_1,  0xa0c8a732      },      /* 0xa0c8a733 */
 200         {       XFER_MW_DMA_0,  0xa0c8a797      },
 201
 202         {       XFER_PIO_4,     0xc0c8a731      },
 203         {       XFER_PIO_3,     0xc0c8a742      },
 204         {       XFER_PIO_2,     0xc0d0a753      },
 205         {       XFER_PIO_1,     0xc0d0a7a3      },      /* 0xc0d0a793 */
 206         {       XFER_PIO_0,     0xc0d0a7aa      },      /* 0xc0d0a7a7 */
 207         {       0,              0x0120a7a7      }
 208 };
 209
 210 static struct chipset_bus_clock_list_entry twenty_five_base_hpt366[] = {
 211         {       XFER_UDMA_4,    0x90c98521      },
 212         {       XFER_UDMA_3,    0x90cf8521      },
 213         {       XFER_UDMA_2,    0x90cf8521      },
 214         {       XFER_UDMA_1,    0x90cb8521      },
 215         {       XFER_UDMA_0,    0x90cb8521      },
 216
 217         {       XFER_MW_DMA_2,  0xa0ca8521      },
 218         {       XFER_MW_DMA_1,  0xa0ca8532      },
 219         {       XFER_MW_DMA_0,  0xa0ca8575      },
 220
 221         {       XFER_PIO_4,     0xc0ca8521      },
 222         {       XFER_PIO_3,     0xc0ca8532      },
 223         {       XFER_PIO_2,     0xc0ca8542      },
 224         {       XFER_PIO_1,     0xc0d08572      },
 225         {       XFER_PIO_0,     0xc0d08585      },
 226         {       0,              0x01208585      }
 227 };
 228
 229 /* from highpoint documentation. these are old values */
 230 static struct chipset_bus_clock_list_entry thirty_three_base_hpt370[] = {
 231 /*      {       XFER_UDMA_5,    0x1A85F442,     0x16454e31      }, */
 232         {       XFER_UDMA_5,    0x16454e31      },
 233         {       XFER_UDMA_4,    0x16454e31      },
 234         {       XFER_UDMA_3,    0x166d4e31      },
 235         {       XFER_UDMA_2,    0x16494e31      },
 236         {       XFER_UDMA_1,    0x164d4e31      },
 237         {       XFER_UDMA_0,    0x16514e31      },
 238
 239         {       XFER_MW_DMA_2,  0x26514e21      },
 240         {       XFER_MW_DMA_1,  0x26514e33      },
 241         {       XFER_MW_DMA_0,  0x26514e97      },
 242
 243         {       XFER_PIO_4,     0x06514e21      },
 244         {       XFER_PIO_3,     0x06514e22      },
 245         {       XFER_PIO_2,     0x06514e33      },
 246         {       XFER_PIO_1,     0x06914e43      },
 247         {       XFER_PIO_0,     0x06914e57      },
 248         {       0,              0x06514e57      }
 249 };
 250
 251 static struct chipset_bus_clock_list_entry sixty_six_base_hpt370[] = {
 252         {       XFER_UDMA_5,    0x14846231      },
 253         {       XFER_UDMA_4,    0x14886231      },
 254         {       XFER_UDMA_3,    0x148c6231      },
 255         {       XFER_UDMA_2,    0x148c6231      },
 256         {       XFER_UDMA_1,    0x14906231      },
 257         {       XFER_UDMA_0,    0x14986231      },
 258
 259         {       XFER_MW_DMA_2,  0x26514e21      },
 260         {       XFER_MW_DMA_1,  0x26514e33      },
 261         {       XFER_MW_DMA_0,  0x26514e97      },
 262
 263         {       XFER_PIO_4,     0x06514e21      },
 264         {       XFER_PIO_3,     0x06514e22      },
 265         {       XFER_PIO_2,     0x06514e33      },
 266         {       XFER_PIO_1,     0x06914e43      },
 267         {       XFER_PIO_0,     0x06914e57      },
 268         {       0,              0x06514e57      }
 269 };
 270
 271 /* these are the current (4 sep 2001) timings from highpoint */
 272 static struct chipset_bus_clock_list_entry thirty_three_base_hpt370a[] = {
 273         {       XFER_UDMA_5,    0x12446231      },
 274         {       XFER_UDMA_4,    0x12446231      },
 275         {       XFER_UDMA_3,    0x126c6231      },
 276         {       XFER_UDMA_2,    0x12486231      },
 277         {       XFER_UDMA_1,    0x124c6233      },
 278         {       XFER_UDMA_0,    0x12506297      },
 279
 280         {       XFER_MW_DMA_2,  0x22406c31      },
 281         {       XFER_MW_DMA_1,  0x22406c33      },
 282         {       XFER_MW_DMA_0,  0x22406c97      },
 283
 284         {       XFER_PIO_4,     0x06414e31      },
 285         {       XFER_PIO_3,     0x06414e42      },
 286         {       XFER_PIO_2,     0x06414e53      },
 287         {       XFER_PIO_1,     0x06814e93      },
 288         {       XFER_PIO_0,     0x06814ea7      },
 289         {       0,              0x06814ea7      }
 290 };
 291
 292 /* 2x 33MHz timings */
 293 static struct chipset_bus_clock_list_entry sixty_six_base_hpt370a[] = {
 294         {       XFER_UDMA_5,    0x1488e673      },
 295         {       XFER_UDMA_4,    0x1488e673      },
 296         {       XFER_UDMA_3,    0x1498e673      },
 297         {       XFER_UDMA_2,    0x1490e673      },
 298         {       XFER_UDMA_1,    0x1498e677      },
 299         {       XFER_UDMA_0,    0x14a0e73f      },
 300
 301         {       XFER_MW_DMA_2,  0x2480fa73      },
 302         {       XFER_MW_DMA_1,  0x2480fa77      },
 303         {       XFER_MW_DMA_0,  0x2480fb3f      },
 304
 305         {       XFER_PIO_4,     0x0c82be73      },
 306         {       XFER_PIO_3,     0x0c82be95      },
 307         {       XFER_PIO_2,     0x0c82beb7      },
 308         {       XFER_PIO_1,     0x0d02bf37      },
 309         {       XFER_PIO_0,     0x0d02bf5f      },
 310         {       0,              0x0d02bf5f      }
 311 };
 312
 313 static struct chipset_bus_clock_list_entry fifty_base_hpt370a[] = {
 314         {       XFER_UDMA_5,    0x12848242      },
 315         {       XFER_UDMA_4,    0x12ac8242      },
 316         {       XFER_UDMA_3,    0x128c8242      },
 317         {       XFER_UDMA_2,    0x120c8242      },
 318         {       XFER_UDMA_1,    0x12148254      },
 319         {       XFER_UDMA_0,    0x121882ea      },
 320
 321         {       XFER_MW_DMA_2,  0x22808242      },
 322         {       XFER_MW_DMA_1,  0x22808254      },
 323         {       XFER_MW_DMA_0,  0x228082ea      },
 324
 325         {       XFER_PIO_4,     0x0a81f442      },
 326         {       XFER_PIO_3,     0x0a81f443      },
 327         {       XFER_PIO_2,     0x0a81f454      },
 328         {       XFER_PIO_1,     0x0ac1f465      },
 329         {       XFER_PIO_0,     0x0ac1f48a      },
 330         {       0,              0x0ac1f48a      }
 331 };
 332
 333 static struct chipset_bus_clock_list_entry thirty_three_base_hpt372[] = {
 334         {       XFER_UDMA_6,    0x1c81dc62      },
 335         {       XFER_UDMA_5,    0x1c6ddc62      },
 336         {       XFER_UDMA_4,    0x1c8ddc62      },
 337         {       XFER_UDMA_3,    0x1c8edc62      },      /* checkme */
 338         {       XFER_UDMA_2,    0x1c91dc62      },
 339         {       XFER_UDMA_1,    0x1c9adc62      },      /* checkme */
 340         {       XFER_UDMA_0,    0x1c82dc62      },      /* checkme */
 341
 342         {       XFER_MW_DMA_2,  0x2c829262      },
 343         {       XFER_MW_DMA_1,  0x2c829266      },      /* checkme */
 344         {       XFER_MW_DMA_0,  0x2c82922e      },      /* checkme */
 345
 346         {       XFER_PIO_4,     0x0c829c62      },
 347         {       XFER_PIO_3,     0x0c829c84      },
 348         {       XFER_PIO_2,     0x0c829ca6      },
 349         {       XFER_PIO_1,     0x0d029d26      },
 350         {       XFER_PIO_0,     0x0d029d5e      },
 351         {       0,              0x0d029d5e      }
 352 };
 353
 354 static struct chipset_bus_clock_list_entry fifty_base_hpt372[] = {
 355         {       XFER_UDMA_5,    0x12848242      },
 356         {       XFER_UDMA_4,    0x12ac8242      },
 357         {       XFER_UDMA_3,    0x128c8242      },
 358         {       XFER_UDMA_2,    0x120c8242      },
 359         {       XFER_UDMA_1,    0x12148254      },
 360         {       XFER_UDMA_0,    0x121882ea      },
 361
 362         {       XFER_MW_DMA_2,  0x22808242      },
 363         {       XFER_MW_DMA_1,  0x22808254      },
 364         {       XFER_MW_DMA_0,  0x228082ea      },
 365
 366         {       XFER_PIO_4,     0x0a81f442      },
 367         {       XFER_PIO_3,     0x0a81f443      },
 368         {       XFER_PIO_2,     0x0a81f454      },
 369         {       XFER_PIO_1,     0x0ac1f465      },
 370         {       XFER_PIO_0,     0x0ac1f48a      },
 371         {       0,              0x0a81f443      }
 372 };
 373
 374 static struct chipset_bus_clock_list_entry sixty_six_base_hpt372[] = {
 375         {       XFER_UDMA_6,    0x1c869c62      },
 376         {       XFER_UDMA_5,    0x1cae9c62      },
 377         {       XFER_UDMA_4,    0x1c8a9c62      },
 378         {       XFER_UDMA_3,    0x1c8e9c62      },
 379         {       XFER_UDMA_2,    0x1c929c62      },
 380         {       XFER_UDMA_1,    0x1c9a9c62      },
 381         {       XFER_UDMA_0,    0x1c829c62      },
 382
 383         {       XFER_MW_DMA_2,  0x2c829c62      },
 384         {       XFER_MW_DMA_1,  0x2c829c66      },
 385         {       XFER_MW_DMA_0,  0x2c829d2e      },
 386
 387         {       XFER_PIO_4,     0x0c829c62      },
 388         {       XFER_PIO_3,     0x0c829c84      },
 389         {       XFER_PIO_2,     0x0c829ca6      },
 390         {       XFER_PIO_1,     0x0d029d26      },
 391         {       XFER_PIO_0,     0x0d029d5e      },
 392         {       0,              0x0d029d26      }
 393 };
 394
 395 static struct chipset_bus_clock_list_entry thirty_three_base_hpt374[] = {
 396         {       XFER_UDMA_6,    0x12808242      },
 397         {       XFER_UDMA_5,    0x12848242      },
 398         {       XFER_UDMA_4,    0x12ac8242      },
 399         {       XFER_UDMA_3,    0x128c8242      },
 400         {       XFER_UDMA_2,    0x120c8242      },
 401         {       XFER_UDMA_1,    0x12148254      },
 402         {       XFER_UDMA_0,    0x121882ea      },
 403
 404         {       XFER_MW_DMA_2,  0x22808242      },
 405         {       XFER_MW_DMA_1,  0x22808254      },
 406         {       XFER_MW_DMA_0,  0x228082ea      },
 407
 408         {       XFER_PIO_4,     0x0a81f442      },
 409         {       XFER_PIO_3,     0x0a81f443      },
 410         {       XFER_PIO_2,     0x0a81f454      },
 411         {       XFER_PIO_1,     0x0ac1f465      },
 412         {       XFER_PIO_0,     0x0ac1f48a      },
 413         {       0,              0x06814e93      }
 414 };
 415
 416 /* FIXME: 50MHz timings for HPT374 */
 417
 418 #if 0
 419 static struct chipset_bus_clock_list_entry sixty_six_base_hpt374[] = {
 420         {       XFER_UDMA_6,    0x12406231      },      /* checkme */
 421         {       XFER_UDMA_5,    0x12446231      },      /* 0x14846231 */
 422         {       XFER_UDMA_4,    0x16814ea7      },      /* 0x14886231 */
 423         {       XFER_UDMA_3,    0x16814ea7      },      /* 0x148c6231 */
 424         {       XFER_UDMA_2,    0x16814ea7      },      /* 0x148c6231 */
 425         {       XFER_UDMA_1,    0x16814ea7      },      /* 0x14906231 */
 426         {       XFER_UDMA_0,    0x16814ea7      },      /* 0x14986231 */
 427         {       XFER_MW_DMA_2,  0x16814ea7      },      /* 0x26514e21 */
 428         {       XFER_MW_DMA_1,  0x16814ea7      },      /* 0x26514e97 */
 429         {       XFER_MW_DMA_0,  0x16814ea7      },      /* 0x26514e97 */
 430         {       XFER_PIO_4,     0x06814ea7      },      /* 0x06514e21 */
 431         {       XFER_PIO_3,     0x06814ea7      },      /* 0x06514e22 */
 432         {       XFER_PIO_2,     0x06814ea7      },      /* 0x06514e33 */
 433         {       XFER_PIO_1,     0x06814ea7      },      /* 0x06914e43 */
 434         {       XFER_PIO_0,     0x06814ea7      },      /* 0x06914e57 */
 435         {       0,              0x06814ea7      }
 436 };
 437 #endif
 438
 439 #define HPT366_DEBUG_DRIVE_INFO         0
 440 #define HPT374_ALLOW_ATA133_6           0
 441 #define HPT371_ALLOW_ATA133_6           0
 442 #define HPT302_ALLOW_ATA133_6           0
 443 #define HPT372_ALLOW_ATA133_6           1
 444 #define HPT370_ALLOW_ATA100_5           1
 445 #define HPT366_ALLOW_ATA66_4            1
 446 #define HPT366_ALLOW_ATA66_3            1
 447 #define HPT366_MAX_DEVS                 8
 448
 449 #define F_LOW_PCI_33    0x23
 450 #define F_LOW_PCI_40    0x29
 451 #define F_LOW_PCI_50    0x2d
 452 #define F_LOW_PCI_66    0x42
 453
 454 /*
 455  *      Hold all the highpoint quirks and revision information in one
 456  *      place.
 457  */
 458
 459 struct hpt_info
 460 {
 461         u8 max_mode;            /* Speeds allowed */
 462         int revision;           /* Chipset revision */
 463         int flags;              /* Chipset properties */
 464 #define PLL_MODE        1
 465 #define IS_372N         2
 466                                 /* Speed table */
 467         struct chipset_bus_clock_list_entry *speed;
 468 };
 469
 470 /*
 471  *      This wants fixing so that we do everything not by classrev
 472  *      (which breaks on the newest chips) but by creating an
 473  *      enumeration of chip variants and using that
 474  */
 475
 476 static __devinit u32 hpt_revision (struct pci_dev *dev)
 477 {
 478         u32 class_rev;
 479         pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev);
 480         class_rev &= 0xff;
 481
 482         switch(dev->device) {
 483                 /* Remap new 372N onto 372 */
 484                 case PCI_DEVICE_ID_TTI_HPT372N:
 485                         class_rev = PCI_DEVICE_ID_TTI_HPT372; break;
 486                 case PCI_DEVICE_ID_TTI_HPT374:
 487                         class_rev = PCI_DEVICE_ID_TTI_HPT374; break;
 488                 case PCI_DEVICE_ID_TTI_HPT371:
 489                         class_rev = PCI_DEVICE_ID_TTI_HPT371; break;
 490                 case PCI_DEVICE_ID_TTI_HPT302:
 491                         class_rev = PCI_DEVICE_ID_TTI_HPT302; break;
 492                 case PCI_DEVICE_ID_TTI_HPT372:
 493                         class_rev = PCI_DEVICE_ID_TTI_HPT372; break;
 494                 default:
 495                         break;
 496         }
 497         return class_rev;
 498 }
 499
 500 static int check_in_drive_lists(ide_drive_t *drive, const char **list);
 501
 502 static u8 hpt3xx_ratemask (ide_drive_t *drive)
 503 {
 504         ide_hwif_t *hwif        = drive->hwif;
 505         struct hpt_info *info   = ide_get_hwifdata(hwif);
 506         u8 mode                 = 0;
 507
 508         /* FIXME: TODO - move this to set info->mode once at boot */
 509
 510         if (info->revision >= 8) {              /* HPT374 */
 511                 mode = (HPT374_ALLOW_ATA133_6) ? 4 : 3;
 512         } else if (info->revision >= 7) {       /* HPT371 */
 513                 mode = (HPT371_ALLOW_ATA133_6) ? 4 : 3;
 514         } else if (info->revision >= 6) {       /* HPT302 */
 515                 mode = (HPT302_ALLOW_ATA133_6) ? 4 : 3;
 516         } else if (info->revision >= 5) {       /* HPT372 */
 517                 mode = (HPT372_ALLOW_ATA133_6) ? 4 : 3;
 518         } else if (info->revision >= 4) {       /* HPT370A */
 519                 mode = (HPT370_ALLOW_ATA100_5) ? 3 : 2;
 520         } else if (info->revision >= 3) {       /* HPT370 */
 521                 mode = (HPT370_ALLOW_ATA100_5) ? 3 : 2;
 522                 mode = (check_in_drive_lists(drive, bad_ata33)) ? 0 : mode;
 523         } else {                                /* HPT366 and HPT368 */
 524                 mode = (check_in_drive_lists(drive, bad_ata33)) ? 0 : 2;
 525         }
 526         if (!eighty_ninty_three(drive) && mode)
 527                 mode = min(mode, (u8)1);
 528         return mode;
 529 }
 530
 531 /*
 532  *      Note for the future; the SATA hpt37x we must set
 533  *      either PIO or UDMA modes 0,4,5
 534  */
 535
 536 static u8 hpt3xx_ratefilter (ide_drive_t *drive, u8 speed)
 537 {
 538         ide_hwif_t *hwif        = drive->hwif;
 539         struct hpt_info *info   = ide_get_hwifdata(hwif);
 540         u8 mode                 = hpt3xx_ratemask(drive);
 541
 542         if (drive->media != ide_disk)
 543                 return min(speed, (u8)XFER_PIO_4);
 544
 545         switch(mode) {
 546                 case 0x04:
 547                         speed = min(speed, (u8)XFER_UDMA_6);
 548                         break;
 549                 case 0x03:
 550                         speed = min(speed, (u8)XFER_UDMA_5);
 551                         if (info->revision >= 5)
 552                                 break;
 553                         if (check_in_drive_lists(drive, bad_ata100_5))
 554                                 speed = min(speed, (u8)XFER_UDMA_4);
 555                         break;
 556                 case 0x02:
 557                         speed = min(speed, (u8)XFER_UDMA_4);
 558         /*
 559          * CHECK ME, Does this need to be set to 5 ??
 560          */
 561                         if (info->revision >= 3)
 562                                 break;
 563                         if ((check_in_drive_lists(drive, bad_ata66_4)) ||
 564                             (!(HPT366_ALLOW_ATA66_4)))
 565                                 speed = min(speed, (u8)XFER_UDMA_3);
 566                         if ((check_in_drive_lists(drive, bad_ata66_3)) ||
 567                             (!(HPT366_ALLOW_ATA66_3)))
 568                                 speed = min(speed, (u8)XFER_UDMA_2);
 569                         break;
 570                 case 0x01:
 571                         speed = min(speed, (u8)XFER_UDMA_2);
 572         /*
 573          * CHECK ME, Does this need to be set to 5 ??
 574          */
 575                         if (info->revision >= 3)
 576                                 break;
 577                         if (check_in_drive_lists(drive, bad_ata33))
 578                                 speed = min(speed, (u8)XFER_MW_DMA_2);
 579                         break;
 580                 case 0x00:
 581                 default:
 582                         speed = min(speed, (u8)XFER_MW_DMA_2);
 583                         break;
 584         }
 585         return speed;
 586 }
 587
 588 static int check_in_drive_lists (ide_drive_t *drive, const char **list)
 589 {
 590         struct hd_driveid *id = drive->id;
 591
 592         if (quirk_drives == list) {
 593                 while (*list)
 594                         if (strstr(id->model, *list++))
 595                                 return 1;
 596         } else {
 597                 while (*list)
 598                         if (!strcmp(*list++,id->model))
 599                                 return 1;
 600         }
 601         return 0;
 602 }
 603
 604 static unsigned int pci_bus_clock_list (u8 speed, struct chipset_bus_clock_list_entry * chipset_table)
 605 {
 606         for ( ; chipset_table->xfer_speed ; chipset_table++)
 607                 if (chipset_table->xfer_speed == speed)
 608                         return chipset_table->chipset_settings;
 609         return chipset_table->chipset_settings;
 610 }
 611
 612 static int hpt36x_tune_chipset(ide_drive_t *drive, u8 xferspeed)
 613 {
 614         ide_hwif_t *hwif        = drive->hwif;
 615         struct pci_dev *dev     = hwif->pci_dev;
 616         struct hpt_info *info   = ide_get_hwifdata(hwif);
 617         u8 speed                = hpt3xx_ratefilter(drive, xferspeed);
 618         u8 regtime              = (drive->select.b.unit & 0x01) ? 0x44 : 0x40;
 619         u8 regfast              = (hwif->channel) ? 0x55 : 0x51;
 620         u8 drive_fast           = 0;
 621         u32 reg1 = 0, reg2      = 0;
 622
 623         /*
 624          * Disable the "fast interrupt" prediction.
 625          */
 626         pci_read_config_byte(dev, regfast, &drive_fast);
 627         if (drive_fast & 0x80)
 628                 pci_write_config_byte(dev, regfast, drive_fast & ~0x80);
 629
 630         reg2 = pci_bus_clock_list(speed, info->speed);
 631
 632         /*
 633          * Disable on-chip PIO FIFO/buffer
 634          *  (to avoid problems handling I/O errors later)
 635          */
 636         pci_read_config_dword(dev, regtime, &reg1);
 637         if (speed >= XFER_MW_DMA_0) {
 638                 reg2 = (reg2 & ~0xc0000000) | (reg1 & 0xc0000000);
 639         } else {
 640                 reg2 = (reg2 & ~0x30070000) | (reg1 & 0x30070000);
 641         }
 642         reg2 &= ~0x80000000;
 643
 644         pci_write_config_dword(dev, regtime, reg2);
 645
 646         return ide_config_drive_speed(drive, speed);
 647 }
 648
 649 static int hpt370_tune_chipset(ide_drive_t *drive, u8 xferspeed)
 650 {
 651         ide_hwif_t *hwif        = drive->hwif;
 652         struct pci_dev *dev = hwif->pci_dev;
 653         struct hpt_info *info   = ide_get_hwifdata(hwif);
 654         u8 speed        = hpt3xx_ratefilter(drive, xferspeed);
 655         u8 regfast      = (drive->hwif->channel) ? 0x55 : 0x51;
 656         u8 drive_pci    = 0x40 + (drive->dn * 4);
 657         u8 new_fast     = 0, drive_fast = 0;
 658         u32 list_conf   = 0, drive_conf = 0;
 659         u32 conf_mask   = (speed >= XFER_MW_DMA_0) ? 0xc0000000 : 0x30070000;
 660
 661         /*
 662          * Disable the "fast interrupt" prediction.
 663          * don't holdoff on interrupts. (== 0x01 despite what the docs say)
 664          */
 665         pci_read_config_byte(dev, regfast, &drive_fast);
 666         new_fast = drive_fast;
 667         if (new_fast & 0x02)
 668                 new_fast &= ~0x02;
 669
 670 #ifdef HPT_DELAY_INTERRUPT
 671         if (new_fast & 0x01)
 672                 new_fast &= ~0x01;
 673 #else
 674         if ((new_fast & 0x01) == 0)
 675                 new_fast |= 0x01;
 676 #endif
 677         if (new_fast != drive_fast)
 678                 pci_write_config_byte(dev, regfast, new_fast);
 679
 680         list_conf = pci_bus_clock_list(speed, info->speed);
 681
 682         pci_read_config_dword(dev, drive_pci, &drive_conf);
 683         list_conf = (list_conf & ~conf_mask) | (drive_conf & conf_mask);
 684
 685         if (speed < XFER_MW_DMA_0)
 686                 list_conf &= ~0x80000000; /* Disable on-chip PIO FIFO/buffer */
 687         pci_write_config_dword(dev, drive_pci, list_conf);
 688
 689         return ide_config_drive_speed(drive, speed);
 690 }
 691
 692 static int hpt372_tune_chipset(ide_drive_t *drive, u8 xferspeed)
 693 {
 694         ide_hwif_t *hwif        = drive->hwif;
 695         struct pci_dev *dev     = hwif->pci_dev;
 696         struct hpt_info *info   = ide_get_hwifdata(hwif);
 697         u8 speed        = hpt3xx_ratefilter(drive, xferspeed);
 698         u8 regfast      = (drive->hwif->channel) ? 0x55 : 0x51;
 699         u8 drive_fast   = 0, drive_pci = 0x40 + (drive->dn * 4);
 700         u32 list_conf   = 0, drive_conf = 0;
 701         u32 conf_mask   = (speed >= XFER_MW_DMA_0) ? 0xc0000000 : 0x30070000;
 702
 703         /*
 704          * Disable the "fast interrupt" prediction.
 705          * don't holdoff on interrupts. (== 0x01 despite what the docs say)
 706          */
 707         pci_read_config_byte(dev, regfast, &drive_fast);
 708         drive_fast &= ~0x07;
 709         pci_write_config_byte(dev, regfast, drive_fast);
 710
 711         list_conf = pci_bus_clock_list(speed, info->speed);
 712         pci_read_config_dword(dev, drive_pci, &drive_conf);
 713         list_conf = (list_conf & ~conf_mask) | (drive_conf & conf_mask);
 714         if (speed < XFER_MW_DMA_0)
 715                 list_conf &= ~0x80000000; /* Disable on-chip PIO FIFO/buffer */
 716         pci_write_config_dword(dev, drive_pci, list_conf);
 717
 718         return ide_config_drive_speed(drive, speed);
 719 }
 720
 721 static int hpt3xx_tune_chipset (ide_drive_t *drive, u8 speed)
 722 {
 723         ide_hwif_t *hwif        = drive->hwif;
 724         struct hpt_info *info   = ide_get_hwifdata(hwif);
 725
 726         if (info->revision >= 8)
 727                 return hpt372_tune_chipset(drive, speed); /* not a typo */
 728         else if (info->revision >= 5)
 729                 return hpt372_tune_chipset(drive, speed);
 730         else if (info->revision >= 3)
 731                 return hpt370_tune_chipset(drive, speed);
 732         else    /* hpt368: hpt_minimum_revision(dev, 2) */
 733                 return hpt36x_tune_chipset(drive, speed);
 734 }
 735
 736 static void hpt3xx_tune_drive (ide_drive_t *drive, u8 pio)
 737 {
 738         pio = ide_get_best_pio_mode(drive, 255, pio, NULL);
 739         (void) hpt3xx_tune_chipset(drive, (XFER_PIO_0 + pio));
 740 }
 741
 742 /*
 743  * This allows the configuration of ide_pci chipset registers
 744  * for cards that learn about the drive's UDMA, DMA, PIO capabilities
 745  * after the drive is reported by the OS.  Initially for designed for
 746  * HPT366 UDMA chipset by HighPoint|Triones Technologies, Inc.
 747  *
 748  * check_in_drive_lists(drive, bad_ata66_4)
 749  * check_in_drive_lists(drive, bad_ata66_3)
 750  * check_in_drive_lists(drive, bad_ata33)
 751  *
 752  */
 753 static int config_chipset_for_dma (ide_drive_t *drive)
 754 {
 755         u8 speed = ide_dma_speed(drive, hpt3xx_ratemask(drive));
 756         ide_hwif_t *hwif = drive->hwif;
 757         struct hpt_info *info   = ide_get_hwifdata(hwif);
 758
 759         if (!speed)
 760                 return 0;
 761
 762         /* If we don't have any timings we can't do a lot */
 763         if (info->speed == NULL)
 764                 return 0;
 765
 766         (void) hpt3xx_tune_chipset(drive, speed);
 767         return ide_dma_enable(drive);
 768 }
 769
 770 static int hpt3xx_quirkproc (ide_drive_t *drive)
 771 {
 772         return ((int) check_in_drive_lists(drive, quirk_drives));
 773 }
 774
 775 static void hpt3xx_intrproc (ide_drive_t *drive)
 776 {
 777         ide_hwif_t *hwif = drive->hwif;
 778
 779         if (drive->quirk_list)
 780                 return;
 781         /* drives in the quirk_list may not like intr setups/cleanups */
 782         hwif->OUTB(drive->ctl|2, IDE_CONTROL_REG);
 783 }
 784
 785 static void hpt3xx_maskproc (ide_drive_t *drive, int mask)
 786 {
 787         ide_hwif_t *hwif = drive->hwif;
 788         struct hpt_info *info = ide_get_hwifdata(hwif);
 789         struct pci_dev *dev = hwif->pci_dev;
 790
 791         if (drive->quirk_list) {
 792                 if (info->revision >= 3) {
 793                         u8 reg5a = 0;
 794                         pci_read_config_byte(dev, 0x5a, &reg5a);
 795                         if (((reg5a & 0x10) >> 4) != mask)
 796                                 pci_write_config_byte(dev, 0x5a, mask ? (reg5a | 0x10) : (reg5a & ~0x10));
 797                 } else {
 798                         if (mask) {
 799                                 disable_irq(hwif->irq);
 800                         } else {
 801                                 enable_irq(hwif->irq);
 802                         }
 803                 }
 804         } else {
 805                 if (IDE_CONTROL_REG)
 806                         hwif->OUTB(mask ? (drive->ctl | 2) :
 807                                                  (drive->ctl & ~2),
 808                                                  IDE_CONTROL_REG);
 809         }
 810 }
 811
 812 static int hpt366_config_drive_xfer_rate (ide_drive_t *drive)
 813 {
 814         ide_hwif_t *hwif        = drive->hwif;
 815         struct hd_driveid *id   = drive->id;
 816
 817         drive->init_speed = 0;
 818
 819         if ((id->capability & 1) && drive->autodma) {
 820
 821                 if (ide_use_dma(drive)) {
 822                         if (config_chipset_for_dma(drive))
 823                                 return hwif->ide_dma_on(drive);
 824                 }
 825
 826                 goto fast_ata_pio;
 827
 828         } else if ((id->capability & 8) || (id->field_valid & 2)) {
 829 fast_ata_pio:
 830                 hpt3xx_tune_drive(drive, 5);
 831                 return hwif->ide_dma_off_quietly(drive);
 832         }
 833         /* IORDY not supported */
 834         return 0;
 835 }
 836
 837 /*
 838  * This is specific to the HPT366 UDMA bios chipset
 839  * by HighPoint|Triones Technologies, Inc.
 840  */
 841 static int hpt366_ide_dma_lostirq (ide_drive_t *drive)
 842 {
 843         struct pci_dev *dev     = HWIF(drive)->pci_dev;
 844         u8 reg50h = 0, reg52h = 0, reg5ah = 0;
 845
 846         pci_read_config_byte(dev, 0x50, &reg50h);
 847         pci_read_config_byte(dev, 0x52, &reg52h);
 848         pci_read_config_byte(dev, 0x5a, &reg5ah);
 849         printk("%s: (%s)  reg50h=0x%02x, reg52h=0x%02x, reg5ah=0x%02x\n",
 850                 drive->name, __FUNCTION__, reg50h, reg52h, reg5ah);
 851         if (reg5ah & 0x10)
 852                 pci_write_config_byte(dev, 0x5a, reg5ah & ~0x10);
 853         return __ide_dma_lostirq(drive);
 854 }
 855
 856 static void hpt370_clear_engine (ide_drive_t *drive)
 857 {
 858         u8 regstate = HWIF(drive)->channel ? 0x54 : 0x50;
 859         pci_write_config_byte(HWIF(drive)->pci_dev, regstate, 0x37);
 860         udelay(10);
 861 }
 862
 863 static void hpt370_ide_dma_start(ide_drive_t *drive)
 864 {
 865 #ifdef HPT_RESET_STATE_ENGINE
 866         hpt370_clear_engine(drive);
 867 #endif
 868         ide_dma_start(drive);
 869 }
 870
 871 static int hpt370_ide_dma_end (ide_drive_t *drive)
 872 {
 873         ide_hwif_t *hwif        = HWIF(drive);
 874         u8 dma_stat             = hwif->INB(hwif->dma_status);
 875
 876         if (dma_stat & 0x01) {
 877                 /* wait a little */
 878                 udelay(20);
 879                 dma_stat = hwif->INB(hwif->dma_status);
 880         }
 881         if ((dma_stat & 0x01) != 0)
 882                 /* fallthrough */
 883                 (void) HWIF(drive)->ide_dma_timeout(drive);
 884
 885         return __ide_dma_end(drive);
 886 }
 887
 888 static void hpt370_lostirq_timeout (ide_drive_t *drive)
 889 {
 890         ide_hwif_t *hwif        = HWIF(drive);
 891         u8 bfifo = 0, reginfo   = hwif->channel ? 0x56 : 0x52;
 892         u8 dma_stat = 0, dma_cmd = 0;
 893
 894         pci_read_config_byte(HWIF(drive)->pci_dev, reginfo, &bfifo);
 895         printk(KERN_DEBUG "%s: %d bytes in FIFO\n", drive->name, bfifo);
 896         hpt370_clear_engine(drive);
 897         /* get dma command mode */
 898         dma_cmd = hwif->INB(hwif->dma_command);
 899         /* stop dma */
 900         hwif->OUTB(dma_cmd & ~0x1, hwif->dma_command);
 901         dma_stat = hwif->INB(hwif->dma_status);
 902         /* clear errors */
 903         hwif->OUTB(dma_stat | 0x6, hwif->dma_status);
 904 }
 905
 906 static int hpt370_ide_dma_timeout (ide_drive_t *drive)
 907 {
 908         hpt370_lostirq_timeout(drive);
 909         hpt370_clear_engine(drive);
 910         return __ide_dma_timeout(drive);
 911 }
 912
 913 static int hpt370_ide_dma_lostirq (ide_drive_t *drive)
 914 {
 915         hpt370_lostirq_timeout(drive);
 916         hpt370_clear_engine(drive);
 917         return __ide_dma_lostirq(drive);
 918 }
 919
 920 /* returns 1 if DMA IRQ issued, 0 otherwise */
 921 static int hpt374_ide_dma_test_irq(ide_drive_t *drive)
 922 {
 923         ide_hwif_t *hwif        = HWIF(drive);
 924         u16 bfifo               = 0;
 925         u8 reginfo              = hwif->channel ? 0x56 : 0x52;
 926         u8 dma_stat;
 927
 928         pci_read_config_word(hwif->pci_dev, reginfo, &bfifo);
 929         if (bfifo & 0x1FF) {
 930 //              printk("%s: %d bytes in FIFO\n", drive->name, bfifo);
 931                 return 0;
 932         }
 933
 934         dma_stat = hwif->INB(hwif->dma_status);
 935         /* return 1 if INTR asserted */
 936         if ((dma_stat & 4) == 4)
 937                 return 1;
 938
 939         if (!drive->waiting_for_dma)
 940                 printk(KERN_WARNING "%s: (%s) called while not waiting\n",
 941                                 drive->name, __FUNCTION__);
 942         return 0;
 943 }
 944
 945 static int hpt374_ide_dma_end (ide_drive_t *drive)
 946 {
 947         struct pci_dev *dev     = HWIF(drive)->pci_dev;
 948         ide_hwif_t *hwif        = HWIF(drive);
 949         u8 msc_stat = 0, mscreg = hwif->channel ? 0x54 : 0x50;
 950         u8 bwsr_stat = 0, bwsr_mask = hwif->channel ? 0x02 : 0x01;
 951
 952         pci_read_config_byte(dev, 0x6a, &bwsr_stat);
 953         pci_read_config_byte(dev, mscreg, &msc_stat);
 954         if ((bwsr_stat & bwsr_mask) == bwsr_mask)
 955                 pci_write_config_byte(dev, mscreg, msc_stat|0x30);
 956         return __ide_dma_end(drive);
 957 }
 958
 959 /**
 960  *      hpt372n_set_clock       -       perform clock switching dance
 961  *      @drive: Drive to switch
 962  *      @mode: Switching mode (0x21 for write, 0x23 otherwise)
 963  *
 964  *      Switch the DPLL clock on the HPT372N devices. This is a
 965  *      right mess.
 966  */
 967
 968 static void hpt372n_set_clock(ide_drive_t *drive, int mode)
 969 {
 970         ide_hwif_t *hwif        = HWIF(drive);
 971
 972         /* FIXME: should we check for DMA active and BUG() */
 973         /* Tristate the bus */
 974         outb(0x80, hwif->dma_base+0x73);
 975         outb(0x80, hwif->dma_base+0x77);
 976
 977         /* Switch clock and reset channels */
 978         outb(mode, hwif->dma_base+0x7B);
 979         outb(0xC0, hwif->dma_base+0x79);
 980
 981         /* Reset state machines */
 982         outb(0x37, hwif->dma_base+0x70);
 983         outb(0x37, hwif->dma_base+0x74);
 984
 985         /* Complete reset */
 986         outb(0x00, hwif->dma_base+0x79);
 987
 988         /* Reconnect channels to bus */
 989         outb(0x00, hwif->dma_base+0x73);
 990         outb(0x00, hwif->dma_base+0x77);
 991 }
 992
 993 /**
 994  *      hpt372n_rw_disk         -       prepare for I/O
 995  *      @drive: drive for command
 996  *      @rq: block request structure
 997  *
 998  *      This is called when a disk I/O is issued to the 372N.
 999  *      We need it because of the clock switching.
1000  */
1001
1002 static void hpt372n_rw_disk(ide_drive_t *drive, struct request *rq)
1003 {
1004         ide_hwif_t *hwif = drive->hwif;
1005         int wantclock;
1006
1007         wantclock = rq_data_dir(rq) ? 0x23 : 0x21;
1008
1009         if (hwif->config_data != wantclock) {
1010                 hpt372n_set_clock(drive, wantclock);
1011                 hwif->config_data = wantclock;
1012         }
1013 }
1014
1015 /*
1016  * Since SUN Cobalt is attempting to do this operation, I should disclose
1017  * this has been a long time ago Thu Jul 27 16:40:57 2000 was the patch date
1018  * HOTSWAP ATA Infrastructure.
1019  */
1020
1021 static void hpt3xx_reset (ide_drive_t *drive)
1022 {
1023 }
1024
1025 static int hpt3xx_tristate (ide_drive_t * drive, int state)
1026 {
1027         ide_hwif_t *hwif        = HWIF(drive);
1028         struct pci_dev *dev     = hwif->pci_dev;
1029         u8 reg59h = 0, reset    = (hwif->channel) ? 0x80 : 0x40;
1030         u8 regXXh = 0, state_reg= (hwif->channel) ? 0x57 : 0x53;
1031
1032         pci_read_config_byte(dev, 0x59, &reg59h);
1033         pci_read_config_byte(dev, state_reg, &regXXh);
1034
1035         if (state) {
1036                 (void) ide_do_reset(drive);
1037                 pci_write_config_byte(dev, state_reg, regXXh|0x80);
1038                 pci_write_config_byte(dev, 0x59, reg59h|reset);
1039         } else {
1040                 pci_write_config_byte(dev, 0x59, reg59h & ~(reset));
1041                 pci_write_config_byte(dev, state_reg, regXXh & ~(0x80));
1042                 (void) ide_do_reset(drive);
1043         }
1044         return 0;
1045 }
1046
1047 /*
1048  * set/get power state for a drive.
1049  * turning the power off does the following things:
1050  *   1) soft-reset the drive
1051  *   2) tri-states the ide bus
1052  *
1053  * when we turn things back on, we need to re-initialize things.
1054  */
1055 #define TRISTATE_BIT  0x8000
1056 static int hpt370_busproc(ide_drive_t * drive, int state)
1057 {
1058         ide_hwif_t *hwif        = drive->hwif;
1059         struct pci_dev *dev     = hwif->pci_dev;
1060         u8 tristate = 0, resetmask = 0, bus_reg = 0;
1061         u16 tri_reg;
1062
1063         hwif->bus_state = state;
1064
1065         if (hwif->channel) {
1066                 /* secondary channel */
1067                 tristate = 0x56;
1068                 resetmask = 0x80;
1069         } else {
1070                 /* primary channel */
1071                 tristate = 0x52;
1072                 resetmask = 0x40;
1073         }
1074
1075         /* grab status */
1076         pci_read_config_word(dev, tristate, &tri_reg);
1077         pci_read_config_byte(dev, 0x59, &bus_reg);
1078
1079         /* set the state. we don't set it if we don't need to do so.
1080          * make sure that the drive knows that it has failed if it's off */
1081         switch (state) {
1082         case BUSSTATE_ON:
1083                 hwif->drives[0].failures = 0;
1084                 hwif->drives[1].failures = 0;
1085                 if ((bus_reg & resetmask) == 0)
1086                         return 0;
1087                 tri_reg &= ~TRISTATE_BIT;
1088                 bus_reg &= ~resetmask;
1089                 break;
1090         case BUSSTATE_OFF:
1091                 hwif->drives[0].failures = hwif->drives[0].max_failures + 1;
1092                 hwif->drives[1].failures = hwif->drives[1].max_failures + 1;
1093                 if ((tri_reg & TRISTATE_BIT) == 0 && (bus_reg & resetmask))
1094                         return 0;
1095                 tri_reg &= ~TRISTATE_BIT;
1096                 bus_reg |= resetmask;
1097                 break;
1098         case BUSSTATE_TRISTATE:
1099                 hwif->drives[0].failures = hwif->drives[0].max_failures + 1;
1100                 hwif->drives[1].failures = hwif->drives[1].max_failures + 1;
1101                 if ((tri_reg & TRISTATE_BIT) && (bus_reg & resetmask))
1102                         return 0;
1103                 tri_reg |= TRISTATE_BIT;
1104                 bus_reg |= resetmask;
1105                 break;
1106         }
1107         pci_write_config_byte(dev, 0x59, bus_reg);
1108         pci_write_config_word(dev, tristate, tri_reg);
1109
1110         return 0;
1111 }
1112
1113 static void __devinit hpt366_clocking(ide_hwif_t *hwif)
1114 {
1115         u32 reg1        = 0;
1116         struct hpt_info *info = ide_get_hwifdata(hwif);
1117
1118         pci_read_config_dword(hwif->pci_dev, 0x40, &reg1);
1119
1120         /* detect bus speed by looking at control reg timing: */
1121         switch((reg1 >> 8) & 7) {
1122                 case 5:
1123                         info->speed = forty_base_hpt366;
1124                         break;
1125                 case 9:
1126                         info->speed = twenty_five_base_hpt366;
1127                         break;
1128                 case 7:
1129                 default:
1130                         info->speed = thirty_three_base_hpt366;
1131                         break;
1132         }
1133 }
1134
1135 static void __devinit hpt37x_clocking(ide_hwif_t *hwif)
1136 {
1137         struct hpt_info *info = ide_get_hwifdata(hwif);
1138         struct pci_dev *dev = hwif->pci_dev;
1139         int adjust, i;
1140         u16 freq;
1141         u32 pll;
1142         u8 reg5bh;
1143
1144         /*
1145          * default to pci clock. make sure MA15/16 are set to output
1146          * to prevent drives having problems with 40-pin cables. Needed
1147          * for some drives such as IBM-DTLA which will not enter ready
1148          * state on reset when PDIAG is a input.
1149          *
1150          * ToDo: should we set 0x21 when using PLL mode ?
1151          */
1152         pci_write_config_byte(dev, 0x5b, 0x23);
1153
1154         /*
1155          * set up the PLL. we need to adjust it so that it's stable.
1156          * freq = Tpll * 192 / Tpci
1157          *
1158          * Todo. For non x86 should probably check the dword is
1159          * set to 0xABCDExxx indicating the BIOS saved f_CNT
1160          */
1161         pci_read_config_word(dev, 0x78, &freq);
1162         freq &= 0x1FF;
1163
1164         /*
1165          * The 372N uses different PCI clock information and has
1166          * some other complications
1167          *      On PCI33 timing we must clock switch
1168          *      On PCI66 timing we must NOT use the PCI clock
1169          *
1170          * Currently we always set up the PLL for the 372N
1171          */
1172
1173         if(info->flags & IS_372N)
1174         {
1175                 printk(KERN_INFO "hpt: HPT372N detected, using 372N timing.\n");
1176                 if(freq < 0x55)
1177                         pll = F_LOW_PCI_33;
1178                 else if(freq < 0x70)
1179                         pll = F_LOW_PCI_40;
1180                 else if(freq < 0x7F)
1181                         pll = F_LOW_PCI_50;
1182                 else
1183                         pll = F_LOW_PCI_66;
1184
1185                 printk(KERN_INFO "FREQ: %d PLL: %d\n", freq, pll);
1186
1187                 /* We always use the pll not the PCI clock on 372N */
1188         }
1189         else
1190         {
1191                 if(freq < 0x9C)
1192                         pll = F_LOW_PCI_33;
1193                 else if(freq < 0xb0)
1194                         pll = F_LOW_PCI_40;
1195                 else if(freq <0xc8)
1196                         pll = F_LOW_PCI_50;
1197                 else
1198                         pll = F_LOW_PCI_66;
1199
1200                 if (pll == F_LOW_PCI_33) {
1201                         if (info->revision >= 8)
1202                                 info->speed = thirty_three_base_hpt374;
1203                         else if (info->revision >= 5)
1204                                 info->speed = thirty_three_base_hpt372;
1205                         else if (info->revision >= 4)
1206                                 info->speed = thirty_three_base_hpt370a;
1207                         else
1208                                 info->speed = thirty_three_base_hpt370;
1209                         printk(KERN_DEBUG "HPT37X: using 33MHz PCI clock\n");
1210                 } else if (pll == F_LOW_PCI_40) {
1211                         /* Unsupported */
1212                 } else if (pll == F_LOW_PCI_50) {
1213                         if (info->revision >= 8)
1214                                 info->speed = fifty_base_hpt370a;
1215                         else if (info->revision >= 5)
1216                                 info->speed = fifty_base_hpt372;
1217                         else if (info->revision >= 4)
1218                                 info->speed = fifty_base_hpt370a;
1219                         else
1220                                 info->speed = fifty_base_hpt370a;
1221                         printk(KERN_DEBUG "HPT37X: using 50MHz PCI clock\n");
1222                 } else {
1223                         if (info->revision >= 8) {
1224                                 printk(KERN_ERR "HPT37x: 66MHz timings are not supported.\n");
1225                         }
1226                         else if (info->revision >= 5)
1227                                 info->speed = sixty_six_base_hpt372;
1228                         else if (info->revision >= 4)
1229                                 info->speed = sixty_six_base_hpt370a;
1230                         else
1231                                 info->speed = sixty_six_base_hpt370;
1232                         printk(KERN_DEBUG "HPT37X: using 66MHz PCI clock\n");
1233                 }
1234         }
1235
1236         /*
1237          * only try the pll if we don't have a table for the clock
1238          * speed that we're running at. NOTE: the internal PLL will
1239          * result in slow reads when using a 33MHz PCI clock. we also
1240          * don't like to use the PLL because it will cause glitches
1241          * on PRST/SRST when the HPT state engine gets reset.
1242          *
1243          * ToDo: Use 66MHz PLL when ATA133 devices are present on a
1244          * 372 device so we can get ATA133 support
1245          */
1246         if (info->speed)
1247                 goto init_hpt37X_done;
1248
1249         info->flags |= PLL_MODE;
1250
1251         /*
1252          * FIXME: make this work correctly, esp with 372N as per
1253          * reference driver code.
1254          *
1255          * adjust PLL based upon PCI clock, enable it, and wait for
1256          * stabilization.
1257          */
1258         adjust = 0;
1259         freq = (pll < F_LOW_PCI_50) ? 2 : 4;
1260         while (adjust++ < 6) {
1261                 pci_write_config_dword(dev, 0x5c, (freq + pll) << 16 |
1262                                        pll | 0x100);
1263
1264                 /* wait for clock stabilization */
1265                 for (i = 0; i < 0x50000; i++) {
1266                         pci_read_config_byte(dev, 0x5b, &reg5bh);
1267                         if (reg5bh & 0x80) {
1268                                 /* spin looking for the clock to destabilize */
1269                                 for (i = 0; i < 0x1000; ++i) {
1270                                         pci_read_config_byte(dev, 0x5b,
1271                                                              &reg5bh);
1272                                         if ((reg5bh & 0x80) == 0)
1273                                                 goto pll_recal;
1274                                 }
1275                                 pci_read_config_dword(dev, 0x5c, &pll);
1276                                 pci_write_config_dword(dev, 0x5c,
1277                                                        pll & ~0x100);
1278                                 pci_write_config_byte(dev, 0x5b, 0x21);
1279                                 if (info->revision >= 8)
1280                                         info->speed = fifty_base_hpt370a;
1281                                 else if (info->revision >= 5)
1282                                         info->speed = fifty_base_hpt372;
1283                                 else if (info->revision >= 4)
1284                                         info->speed = fifty_base_hpt370a;
1285                                 else
1286                                         info->speed = fifty_base_hpt370a;
1287                                 printk("HPT37X: using 50MHz internal PLL\n");
1288                                 goto init_hpt37X_done;
1289                         }
1290                 }
1291 pll_recal:
1292                 if (adjust & 1)
1293                         pll -= (adjust >> 1);
1294                 else
1295                         pll += (adjust >> 1);
1296         }
1297
1298 init_hpt37X_done:
1299         if (!info->speed)
1300                 printk(KERN_ERR "HPT37X%s: unknown bus timing [%d %d].\n",
1301                         (info->flags & IS_372N)?"N":"", pll, freq);
1302         /* reset state engine */
1303         pci_write_config_byte(dev, 0x50, 0x37);
1304         pci_write_config_byte(dev, 0x54, 0x37);
1305         udelay(100);
1306 }
1307
1308 static int __devinit init_hpt37x(struct pci_dev *dev)
1309 {
1310         u8 reg5ah;
1311
1312         pci_read_config_byte(dev, 0x5a, &reg5ah);
1313         /* interrupt force enable */
1314         pci_write_config_byte(dev, 0x5a, (reg5ah & ~0x10));
1315         return 0;
1316 }
1317
1318 static int __devinit init_hpt366(struct pci_dev *dev)
1319 {
1320         u32 reg1        = 0;
1321         u8 drive_fast   = 0;
1322
1323         /*
1324          * Disable the "fast interrupt" prediction.
1325          */
1326         pci_read_config_byte(dev, 0x51, &drive_fast);
1327         if (drive_fast & 0x80)
1328                 pci_write_config_byte(dev, 0x51, drive_fast & ~0x80);
1329         pci_read_config_dword(dev, 0x40, &reg1);
1330
1331         return 0;
1332 }
1333
1334 static unsigned int __devinit init_chipset_hpt366(struct pci_dev *dev, const char *name)
1335 {
1336         int ret = 0;
1337
1338         /*
1339          * FIXME: Not portable. Also, why do we enable the ROM in the first place?
1340          * We don't seem to be using it.
1341          */
1342         if (dev->resource[PCI_ROM_RESOURCE].start)
1343                 pci_write_config_dword(dev, PCI_ROM_ADDRESS,
1344                         dev->resource[PCI_ROM_RESOURCE].start | PCI_ROM_ADDRESS_ENABLE);
1345
1346         pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4));
1347         pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78);
1348         pci_write_config_byte(dev, PCI_MIN_GNT, 0x08);
1349         pci_write_config_byte(dev, PCI_MAX_LAT, 0x08);
1350
1351         if (hpt_revision(dev) >= 3)
1352                 ret = init_hpt37x(dev);
1353         else
1354                 ret = init_hpt366(dev);
1355
1356         if (ret)
1357                 return ret;
1358
1359         return dev->irq;
1360 }
1361
1362 static void __devinit init_hwif_hpt366(ide_hwif_t *hwif)
1363 {
1364         struct pci_dev *dev             = hwif->pci_dev;
1365         struct hpt_info *info           = ide_get_hwifdata(hwif);
1366         u8 ata66 = 0, regmask           = (hwif->channel) ? 0x01 : 0x02;
1367
1368         hwif->tuneproc                  = &hpt3xx_tune_drive;
1369         hwif->speedproc                 = &hpt3xx_tune_chipset;
1370         hwif->quirkproc                 = &hpt3xx_quirkproc;
1371         hwif->intrproc                  = &hpt3xx_intrproc;
1372         hwif->maskproc                  = &hpt3xx_maskproc;
1373
1374         if(info->flags & IS_372N)
1375                 hwif->rw_disk = &hpt372n_rw_disk;
1376
1377         /*
1378          * The HPT37x uses the CBLID pins as outputs for MA15/MA16
1379          * address lines to access an external eeprom.  To read valid
1380          * cable detect state the pins must be enabled as inputs.
1381          */
1382         if (info->revision >= 8 && (PCI_FUNC(dev->devfn) & 1)) {
1383                 /*
1384                  * HPT374 PCI function 1
1385                  * - set bit 15 of reg 0x52 to enable TCBLID as input
1386                  * - set bit 15 of reg 0x56 to enable FCBLID as input
1387                  */
1388                 u16 mcr3, mcr6;
1389                 pci_read_config_word(dev, 0x52, &mcr3);
1390                 pci_read_config_word(dev, 0x56, &mcr6);
1391                 pci_write_config_word(dev, 0x52, mcr3 | 0x8000);
1392                 pci_write_config_word(dev, 0x56, mcr6 | 0x8000);
1393                 /* now read cable id register */
1394                 pci_read_config_byte(dev, 0x5a, &ata66);
1395                 pci_write_config_word(dev, 0x52, mcr3);
1396                 pci_write_config_word(dev, 0x56, mcr6);
1397         } else if (info->revision >= 3) {
1398                 /*
1399                  * HPT370/372 and 374 pcifn 0
1400                  * - clear bit 0 of 0x5b to enable P/SCBLID as inputs
1401                  */
1402                 u8 scr2;
1403                 pci_read_config_byte(dev, 0x5b, &scr2);
1404                 pci_write_config_byte(dev, 0x5b, scr2 & ~1);
1405                 /* now read cable id register */
1406                 pci_read_config_byte(dev, 0x5a, &ata66);
1407                 pci_write_config_byte(dev, 0x5b, scr2);
1408         } else {
1409                 pci_read_config_byte(dev, 0x5a, &ata66);
1410         }
1411
1412 #ifdef DEBUG
1413         printk("HPT366: reg5ah=0x%02x ATA-%s Cable Port%d\n",
1414                 ata66, (ata66 & regmask) ? "33" : "66",
1415                 PCI_FUNC(hwif->pci_dev->devfn));
1416 #endif /* DEBUG */
1417
1418 #ifdef HPT_SERIALIZE_IO
1419         /* serialize access to this device */
1420         if (hwif->mate)
1421                 hwif->serialized = hwif->mate->serialized = 1;
1422 #endif
1423
1424         if (info->revision >= 3) {
1425                 u8 reg5ah = 0;
1426                         pci_write_config_byte(dev, 0x5a, reg5ah & ~0x10);
1427                 /*
1428                  * set up ioctl for power status.
1429                  * note: power affects both
1430                  * drives on each channel
1431                  */
1432                 hwif->resetproc = &hpt3xx_reset;
1433                 hwif->busproc   = &hpt370_busproc;
1434         } else if (info->revision >= 2) {
1435                 hwif->resetproc = &hpt3xx_reset;
1436                 hwif->busproc   = &hpt3xx_tristate;
1437         } else {
1438                 hwif->resetproc = &hpt3xx_reset;
1439                 hwif->busproc   = &hpt3xx_tristate;
1440         }
1441
1442         if (!hwif->dma_base) {
1443                 hwif->drives[0].autotune = 1;
1444                 hwif->drives[1].autotune = 1;
1445                 return;
1446         }
1447
1448         hwif->ultra_mask = 0x7f;
1449         hwif->mwdma_mask = 0x07;
1450
1451         if (!(hwif->udma_four))
1452                 hwif->udma_four = ((ata66 & regmask) ? 0 : 1);
1453         hwif->ide_dma_check = &hpt366_config_drive_xfer_rate;
1454
1455         if (info->revision >= 8) {
1456                 hwif->ide_dma_test_irq = &hpt374_ide_dma_test_irq;
1457                 hwif->ide_dma_end = &hpt374_ide_dma_end;
1458         } else if (info->revision >= 5) {
1459                 hwif->ide_dma_test_irq = &hpt374_ide_dma_test_irq;
1460                 hwif->ide_dma_end = &hpt374_ide_dma_end;
1461         } else if (info->revision >= 3) {
1462                 hwif->dma_start = &hpt370_ide_dma_start;
1463                 hwif->ide_dma_end = &hpt370_ide_dma_end;
1464                 hwif->ide_dma_timeout = &hpt370_ide_dma_timeout;
1465                 hwif->ide_dma_lostirq = &hpt370_ide_dma_lostirq;
1466         } else if (info->revision >= 2)
1467                 hwif->ide_dma_lostirq = &hpt366_ide_dma_lostirq;
1468         else
1469                 hwif->ide_dma_lostirq = &hpt366_ide_dma_lostirq;
1470
1471         if (!noautodma)
1472                 hwif->autodma = 1;
1473         hwif->drives[0].autodma = hwif->autodma;
1474         hwif->drives[1].autodma = hwif->autodma;
1475 }
1476
1477 static void __devinit init_dma_hpt366(ide_hwif_t *hwif, unsigned long dmabase)
1478 {
1479         struct hpt_info *info   = ide_get_hwifdata(hwif);
1480         u8 masterdma    = 0, slavedma = 0;
1481         u8 dma_new      = 0, dma_old = 0;
1482         u8 primary      = hwif->channel ? 0x4b : 0x43;
1483         u8 secondary    = hwif->channel ? 0x4f : 0x47;
1484         unsigned long flags;
1485
1486         if (!dmabase)
1487                 return;
1488
1489         if(info->speed == NULL) {
1490                 printk(KERN_WARNING "hpt: no known IDE timings, disabling DMA.\n");
1491                 return;
1492         }
1493
1494         dma_old = hwif->INB(dmabase+2);
1495
1496         local_irq_save(flags);
1497
1498         dma_new = dma_old;
1499         pci_read_config_byte(hwif->pci_dev, primary, &masterdma);
1500         pci_read_config_byte(hwif->pci_dev, secondary, &slavedma);
1501
1502         if (masterdma & 0x30)   dma_new |= 0x20;
1503         if (slavedma & 0x30)    dma_new |= 0x40;
1504         if (dma_new != dma_old)
1505                 hwif->OUTB(dma_new, dmabase+2);
1506
1507         local_irq_restore(flags);
1508
1509         ide_setup_dma(hwif, dmabase, 8);
1510 }
1511
1512 /*
1513  *      We "borrow" this hook in order to set the data structures
1514  *      up early enough before dma or init_hwif calls are made.
1515  */
1516
1517 static void __devinit init_iops_hpt366(ide_hwif_t *hwif)
1518 {
1519         struct hpt_info *info = kmalloc(sizeof(struct hpt_info), GFP_KERNEL);
1520         unsigned long dmabase = pci_resource_start(hwif->pci_dev, 4);
1521         u8 did, rid;
1522
1523         if(info == NULL) {
1524                 printk(KERN_WARNING "hpt366: out of memory.\n");
1525                 return;
1526         }
1527         memset(info, 0, sizeof(struct hpt_info));
1528         ide_set_hwifdata(hwif, info);
1529
1530         if(dmabase) {
1531                 did = inb(dmabase + 0x22);
1532                 rid = inb(dmabase + 0x28);
1533
1534                 if((did == 4 && rid == 6) || (did == 5 && rid > 1))
1535                         info->flags |= IS_372N;
1536         }
1537
1538         info->revision = hpt_revision(hwif->pci_dev);
1539
1540         if (info->revision >= 3)
1541                 hpt37x_clocking(hwif);
1542         else
1543                 hpt366_clocking(hwif);
1544 }
1545
1546 static int __devinit init_setup_hpt374(struct pci_dev *dev, ide_pci_device_t *d)
1547 {
1548         struct pci_dev *findev = NULL;
1549
1550         if (PCI_FUNC(dev->devfn) & 1)
1551                 return -ENODEV;
1552
1553         while ((findev = pci_find_device(PCI_ANY_ID, PCI_ANY_ID, findev)) != NULL) {
1554                 if ((findev->vendor == dev->vendor) &&
1555                     (findev->device == dev->device) &&
1556                     ((findev->devfn - dev->devfn) == 1) &&
1557                     (PCI_FUNC(findev->devfn) & 1)) {
1558                         if (findev->irq != dev->irq) {
1559                                 /* FIXME: we need a core pci_set_interrupt() */
1560                                 findev->irq = dev->irq;
1561                                 printk(KERN_WARNING "%s: pci-config space interrupt "
1562                                         "fixed.\n", d->name);
1563                         }
1564                         return ide_setup_pci_devices(dev, findev, d);
1565                 }
1566         }
1567         return ide_setup_pci_device(dev, d);
1568 }
1569
1570 static int __devinit init_setup_hpt37x(struct pci_dev *dev, ide_pci_device_t *d)
1571 {
1572         return ide_setup_pci_device(dev, d);
1573 }
1574
1575 static int __devinit init_setup_hpt366(struct pci_dev *dev, ide_pci_device_t *d)
1576 {
1577         struct pci_dev *findev = NULL;
1578         u8 pin1 = 0, pin2 = 0;
1579         unsigned int class_rev;
1580         char *chipset_names[] = {"HPT366", "HPT366",  "HPT368",
1581                                  "HPT370", "HPT370A", "HPT372",
1582                                  "HPT372N" };
1583
1584         if (PCI_FUNC(dev->devfn) & 1)
1585                 return -ENODEV;
1586
1587         pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev);
1588         class_rev &= 0xff;
1589
1590         if(dev->device == PCI_DEVICE_ID_TTI_HPT372N)
1591                 class_rev = 6;
1592
1593         if(class_rev <= 6)
1594                 d->name = chipset_names[class_rev];
1595
1596         switch(class_rev) {
1597                 case 6:
1598                 case 5:
1599                 case 4:
1600                 case 3:
1601                         goto init_single;
1602                 default:
1603                         break;
1604         }
1605
1606         d->channels = 1;
1607
1608         pci_read_config_byte(dev, PCI_INTERRUPT_PIN, &pin1);
1609         while ((findev = pci_find_device(PCI_ANY_ID, PCI_ANY_ID, findev)) != NULL) {
1610                 if ((findev->vendor == dev->vendor) &&
1611                     (findev->device == dev->device) &&
1612                     ((findev->devfn - dev->devfn) == 1) &&
1613                     (PCI_FUNC(findev->devfn) & 1)) {
1614                         pci_read_config_byte(findev, PCI_INTERRUPT_PIN, &pin2);
1615                         if ((pin1 != pin2) && (dev->irq == findev->irq)) {
1616                                 d->bootable = ON_BOARD;
1617                                 printk("%s: onboard version of chipset, "
1618                                         "pin1=%d pin2=%d\n", d->name,
1619                                         pin1, pin2);
1620                         }
1621                         return ide_setup_pci_devices(dev, findev, d);
1622                 }
1623         }
1624 init_single:
1625         return ide_setup_pci_device(dev, d);
1626 }
1627
1628 static ide_pci_device_t hpt366_chipsets[] __devinitdata = {
1629         {       /* 0 */
1630                 .name           = "HPT366",
1631                 .init_setup     = init_setup_hpt366,
1632                 .init_chipset   = init_chipset_hpt366,
1633                 .init_iops      = init_iops_hpt366,
1634                 .init_hwif      = init_hwif_hpt366,
1635                 .init_dma       = init_dma_hpt366,
1636                 .channels       = 2,
1637                 .autodma        = AUTODMA,
1638                 .bootable       = OFF_BOARD,
1639                 .extra          = 240
1640         },{     /* 1 */
1641                 .name           = "HPT372A",
1642                 .init_setup     = init_setup_hpt37x,
1643                 .init_chipset   = init_chipset_hpt366,
1644                 .init_iops      = init_iops_hpt366,
1645                 .init_hwif      = init_hwif_hpt366,
1646                 .init_dma       = init_dma_hpt366,
1647                 .channels       = 2,
1648                 .autodma        = AUTODMA,
1649                 .bootable       = OFF_BOARD,
1650         },{     /* 2 */
1651                 .name           = "HPT302",
1652                 .init_setup     = init_setup_hpt37x,
1653                 .init_chipset   = init_chipset_hpt366,
1654                 .init_iops      = init_iops_hpt366,
1655                 .init_hwif      = init_hwif_hpt366,
1656                 .init_dma       = init_dma_hpt366,
1657                 .channels       = 2,
1658                 .autodma        = AUTODMA,
1659                 .bootable       = OFF_BOARD,
1660         },{     /* 3 */
1661                 .name           = "HPT371",
1662                 .init_setup     = init_setup_hpt37x,
1663                 .init_chipset   = init_chipset_hpt366,
1664                 .init_iops      = init_iops_hpt366,
1665                 .init_hwif      = init_hwif_hpt366,
1666                 .init_dma       = init_dma_hpt366,
1667                 .channels       = 2,
1668                 .autodma        = AUTODMA,
1669                 .bootable       = OFF_BOARD,
1670         },{     /* 4 */
1671                 .name           = "HPT374",
1672                 .init_setup     = init_setup_hpt374,
1673                 .init_chipset   = init_chipset_hpt366,
1674                 .init_iops      = init_iops_hpt366,
1675                 .init_hwif      = init_hwif_hpt366,
1676                 .init_dma       = init_dma_hpt366,
1677                 .channels       = 2,    /* 4 */
1678                 .autodma        = AUTODMA,
1679                 .bootable       = OFF_BOARD,
1680         },{     /* 5 */
1681                 .name           = "HPT372N",
1682                 .init_setup     = init_setup_hpt37x,
1683                 .init_chipset   = init_chipset_hpt366,
1684                 .init_iops      = init_iops_hpt366,
1685                 .init_hwif      = init_hwif_hpt366,
1686                 .init_dma       = init_dma_hpt366,
1687                 .channels       = 2,    /* 4 */
1688                 .autodma        = AUTODMA,
1689                 .bootable       = OFF_BOARD,
1690         }
1691 };
1692
1693 /**
1694  *      hpt366_init_one -       called when an HPT366 is found
1695  *      @dev: the hpt366 device
1696  *      @id: the matching pci id
1697  *
1698  *      Called when the PCI registration layer (or the IDE initialization)
1699  *      finds a device matching our IDE device tables.
1700  */
1701
1702 static int __devinit hpt366_init_one(struct pci_dev *dev, const struct pci_device_id *id)
1703 {
1704         ide_pci_device_t *d = &hpt366_chipsets[id->driver_data];
1705
1706         return d->init_setup(dev, d);
1707 }
1708
1709 static struct pci_device_id hpt366_pci_tbl[] = {
1710         { PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT366, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
1711         { PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT372, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1},
1712         { PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT302, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2},
1713         { PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT371, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 3},
1714         { PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT374, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4},
1715         { PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT372N, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 5},
1716         { 0, },
1717 };
1718 MODULE_DEVICE_TABLE(pci, hpt366_pci_tbl);
1719
1720 static struct pci_driver driver = {
1721         .name           = "HPT366_IDE",
1722         .id_table       = hpt366_pci_tbl,
1723         .probe          = hpt366_init_one,
1724 };
1725
1726 static int hpt366_ide_init(void)
1727 {
1728         return ide_pci_register_driver(&driver);
1729 }
1730
1731 module_init(hpt366_ide_init);
1732
1733 MODULE_AUTHOR("Andre Hedrick");
1734 MODULE_DESCRIPTION("PCI driver module for Highpoint HPT366 IDE");
1735 MODULE_LICENSE("GPL");