drivers/i2c/busses/i2c-sprd.c

   1 /*
   2  * Copyright (C) 2017 Spreadtrum Communications Inc.
   3  *
   4  * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
   5  */
   6
   7 #include <linux/clk.h>
   8 #include <linux/delay.h>
   9 #include <linux/err.h>
  10 #include <linux/io.h>
  11 #include <linux/i2c.h>
  12 #include <linux/init.h>
  13 #include <linux/interrupt.h>
  14 #include <linux/kernel.h>
  15 #include <linux/of.h>
  16 #include <linux/of_device.h>
  17 #include <linux/platform_device.h>
  18 #include <linux/pm_runtime.h>
  19
  20 #define I2C_CTL                 0x00
  21 #define I2C_ADDR_CFG            0x04
  22 #define I2C_COUNT               0x08
  23 #define I2C_RX                  0x0c
  24 #define I2C_TX                  0x10
  25 #define I2C_STATUS              0x14
  26 #define I2C_HSMODE_CFG          0x18
  27 #define I2C_VERSION             0x1c
  28 #define ADDR_DVD0               0x20
  29 #define ADDR_DVD1               0x24
  30 #define ADDR_STA0_DVD           0x28
  31 #define ADDR_RST                0x2c
  32
  33 /* I2C_CTL */
  34 #define STP_EN                  BIT(20)
  35 #define FIFO_AF_LVL_MASK        GENMASK(19, 16)
  36 #define FIFO_AF_LVL             16
  37 #define FIFO_AE_LVL_MASK        GENMASK(15, 12)
  38 #define FIFO_AE_LVL             12
  39 #define I2C_DMA_EN              BIT(11)
  40 #define FULL_INTEN              BIT(10)
  41 #define EMPTY_INTEN             BIT(9)
  42 #define I2C_DVD_OPT             BIT(8)
  43 #define I2C_OUT_OPT             BIT(7)
  44 #define I2C_TRIM_OPT            BIT(6)
  45 #define I2C_HS_MODE             BIT(4)
  46 #define I2C_MODE                BIT(3)
  47 #define I2C_EN                  BIT(2)
  48 #define I2C_INT_EN              BIT(1)
  49 #define I2C_START               BIT(0)
  50
  51 /* I2C_STATUS */
  52 #define SDA_IN                  BIT(21)
  53 #define SCL_IN                  BIT(20)
  54 #define FIFO_FULL               BIT(4)
  55 #define FIFO_EMPTY              BIT(3)
  56 #define I2C_INT                 BIT(2)
  57 #define I2C_RX_ACK              BIT(1)
  58 #define I2C_BUSY                BIT(0)
  59
  60 /* ADDR_RST */
  61 #define I2C_RST                 BIT(0)
  62
  63 #define I2C_FIFO_DEEP           12
  64 #define I2C_FIFO_FULL_THLD      15
  65 #define I2C_FIFO_EMPTY_THLD     4
  66 #define I2C_DATA_STEP           8
  67 #define I2C_ADDR_DVD0_CALC(high, low)   \
  68         ((((high) & GENMASK(15, 0)) << 16) | ((low) & GENMASK(15, 0)))
  69 #define I2C_ADDR_DVD1_CALC(high, low)   \
  70         (((high) & GENMASK(31, 16)) | (((low) & GENMASK(31, 16)) >> 16))
  71
  72 /* timeout (ms) for pm runtime autosuspend */
  73 #define SPRD_I2C_PM_TIMEOUT     1000
  74
  75 /* SPRD i2c data structure */
  76 struct sprd_i2c {
  77         struct i2c_adapter adap;
  78         struct device *dev;
  79         void __iomem *base;
  80         struct i2c_msg *msg;
  81         struct clk *clk;
  82         u32 src_clk;
  83         u32 bus_freq;
  84         struct completion complete;
  85         u8 *buf;
  86         u32 count;
  87         int irq;
  88         int err;
  89         bool is_suspended;
  90 };
  91
  92 static void sprd_i2c_set_count(struct sprd_i2c *i2c_dev, u32 count)
  93 {
  94         writel(count, i2c_dev->base + I2C_COUNT);
  95 }
  96
  97 static void sprd_i2c_send_stop(struct sprd_i2c *i2c_dev, int stop)
  98 {
  99         u32 tmp = readl(i2c_dev->base + I2C_CTL);
 100
 101         if (stop)
 102                 writel(tmp & ~STP_EN, i2c_dev->base + I2C_CTL);
 103         else
 104                 writel(tmp | STP_EN, i2c_dev->base + I2C_CTL);
 105 }
 106
 107 static void sprd_i2c_clear_start(struct sprd_i2c *i2c_dev)
 108 {
 109         u32 tmp = readl(i2c_dev->base + I2C_CTL);
 110
 111         writel(tmp & ~I2C_START, i2c_dev->base + I2C_CTL);
 112 }
 113
 114 static void sprd_i2c_clear_ack(struct sprd_i2c *i2c_dev)
 115 {
 116         u32 tmp = readl(i2c_dev->base + I2C_STATUS);
 117
 118         writel(tmp & ~I2C_RX_ACK, i2c_dev->base + I2C_STATUS);
 119 }
 120
 121 static void sprd_i2c_clear_irq(struct sprd_i2c *i2c_dev)
 122 {
 123         u32 tmp = readl(i2c_dev->base + I2C_STATUS);
 124
 125         writel(tmp & ~I2C_INT, i2c_dev->base + I2C_STATUS);
 126 }
 127
 128 static void sprd_i2c_reset_fifo(struct sprd_i2c *i2c_dev)
 129 {
 130         writel(I2C_RST, i2c_dev->base + ADDR_RST);
 131 }
 132
 133 static void sprd_i2c_set_devaddr(struct sprd_i2c *i2c_dev, struct i2c_msg *m)
 134 {
 135         writel(m->addr << 1, i2c_dev->base + I2C_ADDR_CFG);
 136 }
 137
 138 static void sprd_i2c_write_bytes(struct sprd_i2c *i2c_dev, u8 *buf, u32 len)
 139 {
 140         u32 i;
 141
 142         for (i = 0; i < len; i++)
 143                 writeb(buf[i], i2c_dev->base + I2C_TX);
 144 }
 145
 146 static void sprd_i2c_read_bytes(struct sprd_i2c *i2c_dev, u8 *buf, u32 len)
 147 {
 148         u32 i;
 149
 150         for (i = 0; i < len; i++)
 151                 buf[i] = readb(i2c_dev->base + I2C_RX);
 152 }
 153
 154 static void sprd_i2c_set_full_thld(struct sprd_i2c *i2c_dev, u32 full_thld)
 155 {
 156         u32 tmp = readl(i2c_dev->base + I2C_CTL);
 157
 158         tmp &= ~FIFO_AF_LVL_MASK;
 159         tmp |= full_thld << FIFO_AF_LVL;
 160         writel(tmp, i2c_dev->base + I2C_CTL);
 161 };
 162
 163 static void sprd_i2c_set_empty_thld(struct sprd_i2c *i2c_dev, u32 empty_thld)
 164 {
 165         u32 tmp = readl(i2c_dev->base + I2C_CTL);
 166
 167         tmp &= ~FIFO_AE_LVL_MASK;
 168         tmp |= empty_thld << FIFO_AE_LVL;
 169         writel(tmp, i2c_dev->base + I2C_CTL);
 170 };
 171
 172 static void sprd_i2c_set_fifo_full_int(struct sprd_i2c *i2c_dev, int enable)
 173 {
 174         u32 tmp = readl(i2c_dev->base + I2C_CTL);
 175
 176         if (enable)
 177                 tmp |= FULL_INTEN;
 178         else
 179                 tmp &= ~FULL_INTEN;
 180
 181         writel(tmp, i2c_dev->base + I2C_CTL);
 182 };
 183
 184 static void sprd_i2c_set_fifo_empty_int(struct sprd_i2c *i2c_dev, int enable)
 185 {
 186         u32 tmp = readl(i2c_dev->base + I2C_CTL);
 187
 188         if (enable)
 189                 tmp |= EMPTY_INTEN;
 190         else
 191                 tmp &= ~EMPTY_INTEN;
 192
 193         writel(tmp, i2c_dev->base + I2C_CTL);
 194 };
 195
 196 static void sprd_i2c_opt_start(struct sprd_i2c *i2c_dev)
 197 {
 198         u32 tmp = readl(i2c_dev->base + I2C_CTL);
 199
 200         writel(tmp | I2C_START, i2c_dev->base + I2C_CTL);
 201 }
 202
 203 static void sprd_i2c_opt_mode(struct sprd_i2c *i2c_dev, int rw)
 204 {
 205         u32 cmd = readl(i2c_dev->base + I2C_CTL) & ~I2C_MODE;
 206
 207         writel(cmd | rw << 3, i2c_dev->base + I2C_CTL);
 208 }
 209
 210 static void sprd_i2c_data_transfer(struct sprd_i2c *i2c_dev)
 211 {
 212         u32 i2c_count = i2c_dev->count;
 213         u32 need_tran = i2c_count <= I2C_FIFO_DEEP ? i2c_count : I2C_FIFO_DEEP;
 214         struct i2c_msg *msg = i2c_dev->msg;
 215
 216         if (msg->flags & I2C_M_RD) {
 217                 sprd_i2c_read_bytes(i2c_dev, i2c_dev->buf, I2C_FIFO_FULL_THLD);
 218                 i2c_dev->count -= I2C_FIFO_FULL_THLD;
 219                 i2c_dev->buf += I2C_FIFO_FULL_THLD;
 220
 221                 /*
 222                  * If the read data count is larger than rx fifo full threshold,
 223                  * we should enable the rx fifo full interrupt to read data
 224                  * again.
 225                  */
 226                 if (i2c_dev->count >= I2C_FIFO_FULL_THLD)
 227                         sprd_i2c_set_fifo_full_int(i2c_dev, 1);
 228         } else {
 229                 sprd_i2c_write_bytes(i2c_dev, i2c_dev->buf, need_tran);
 230                 i2c_dev->buf += need_tran;
 231                 i2c_dev->count -= need_tran;
 232
 233                 /*
 234                  * If the write data count is arger than tx fifo depth which
 235                  * means we can not write all data in one time, then we should
 236                  * enable the tx fifo empty interrupt to write again.
 237                  */
 238                 if (i2c_count > I2C_FIFO_DEEP)
 239                         sprd_i2c_set_fifo_empty_int(i2c_dev, 1);
 240         }
 241 }
 242
 243 static int sprd_i2c_handle_msg(struct i2c_adapter *i2c_adap,
 244                                struct i2c_msg *msg, bool is_last_msg)
 245 {
 246         struct sprd_i2c *i2c_dev = i2c_adap->algo_data;
 247
 248         i2c_dev->msg = msg;
 249         i2c_dev->buf = msg->buf;
 250         i2c_dev->count = msg->len;
 251
 252         reinit_completion(&i2c_dev->complete);
 253         sprd_i2c_reset_fifo(i2c_dev);
 254         sprd_i2c_set_devaddr(i2c_dev, msg);
 255         sprd_i2c_set_count(i2c_dev, msg->len);
 256
 257         if (msg->flags & I2C_M_RD) {
 258                 sprd_i2c_opt_mode(i2c_dev, 1);
 259                 sprd_i2c_send_stop(i2c_dev, 1);
 260         } else {
 261                 sprd_i2c_opt_mode(i2c_dev, 0);
 262                 sprd_i2c_send_stop(i2c_dev, !!is_last_msg);
 263         }
 264
 265         /*
 266          * We should enable rx fifo full interrupt to get data when receiving
 267          * full data.
 268          */
 269         if (msg->flags & I2C_M_RD)
 270                 sprd_i2c_set_fifo_full_int(i2c_dev, 1);
 271         else
 272                 sprd_i2c_data_transfer(i2c_dev);
 273
 274         sprd_i2c_opt_start(i2c_dev);
 275
 276         wait_for_completion(&i2c_dev->complete);
 277
 278         return i2c_dev->err;
 279 }
 280
 281 static int sprd_i2c_master_xfer(struct i2c_adapter *i2c_adap,
 282                                 struct i2c_msg *msgs, int num)
 283 {
 284         struct sprd_i2c *i2c_dev = i2c_adap->algo_data;
 285         int im, ret;
 286
 287         if (i2c_dev->is_suspended)
 288                 return -EBUSY;
 289
 290         ret = pm_runtime_get_sync(i2c_dev->dev);
 291         if (ret < 0)
 292                 return ret;
 293
 294         for (im = 0; im < num - 1; im++) {
 295                 ret = sprd_i2c_handle_msg(i2c_adap, &msgs[im], 0);
 296                 if (ret)
 297                         goto err_msg;
 298         }
 299
 300         ret = sprd_i2c_handle_msg(i2c_adap, &msgs[im++], 1);
 301
 302 err_msg:
 303         pm_runtime_mark_last_busy(i2c_dev->dev);
 304         pm_runtime_put_autosuspend(i2c_dev->dev);
 305
 306         return ret < 0 ? ret : im;
 307 }
 308
 309 static u32 sprd_i2c_func(struct i2c_adapter *adap)
 310 {
 311         return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
 312 }
 313
 314 static const struct i2c_algorithm sprd_i2c_algo = {
 315         .master_xfer = sprd_i2c_master_xfer,
 316         .functionality = sprd_i2c_func,
 317 };
 318
 319 static void sprd_i2c_set_clk(struct sprd_i2c *i2c_dev, u32 freq)
 320 {
 321         u32 apb_clk = i2c_dev->src_clk;
 322         /*
 323          * From I2C databook, the prescale calculation formula:
 324          * prescale = freq_i2c / (4 * freq_scl) - 1;
 325          */
 326         u32 i2c_dvd = apb_clk / (4 * freq) - 1;
 327         /*
 328          * From I2C databook, the high period of SCL clock is recommended as
 329          * 40% (2/5), and the low period of SCL clock is recommended as 60%
 330          * (3/5), then the formula should be:
 331          * high = (prescale * 2 * 2) / 5
 332          * low = (prescale * 2 * 3) / 5
 333          */
 334         u32 high = ((i2c_dvd << 1) * 2) / 5;
 335         u32 low = ((i2c_dvd << 1) * 3) / 5;
 336         u32 div0 = I2C_ADDR_DVD0_CALC(high, low);
 337         u32 div1 = I2C_ADDR_DVD1_CALC(high, low);
 338
 339         writel(div0, i2c_dev->base + ADDR_DVD0);
 340         writel(div1, i2c_dev->base + ADDR_DVD1);
 341
 342         /* Start hold timing = hold time(us) * source clock */
 343         if (freq == 400000)
 344                 writel((6 * apb_clk) / 10000000, i2c_dev->base + ADDR_STA0_DVD);
 345         else if (freq == 100000)
 346                 writel((4 * apb_clk) / 1000000, i2c_dev->base + ADDR_STA0_DVD);
 347 }
 348
 349 static void sprd_i2c_enable(struct sprd_i2c *i2c_dev)
 350 {
 351         u32 tmp = I2C_DVD_OPT;
 352
 353         writel(tmp, i2c_dev->base + I2C_CTL);
 354
 355         sprd_i2c_set_full_thld(i2c_dev, I2C_FIFO_FULL_THLD);
 356         sprd_i2c_set_empty_thld(i2c_dev, I2C_FIFO_EMPTY_THLD);
 357
 358         sprd_i2c_set_clk(i2c_dev, i2c_dev->bus_freq);
 359         sprd_i2c_reset_fifo(i2c_dev);
 360         sprd_i2c_clear_irq(i2c_dev);
 361
 362         tmp = readl(i2c_dev->base + I2C_CTL);
 363         writel(tmp | I2C_EN | I2C_INT_EN, i2c_dev->base + I2C_CTL);
 364 }
 365
 366 static irqreturn_t sprd_i2c_isr_thread(int irq, void *dev_id)
 367 {
 368         struct sprd_i2c *i2c_dev = dev_id;
 369         struct i2c_msg *msg = i2c_dev->msg;
 370         bool ack = !(readl(i2c_dev->base + I2C_STATUS) & I2C_RX_ACK);
 371         u32 i2c_tran;
 372
 373         if (msg->flags & I2C_M_RD)
 374                 i2c_tran = i2c_dev->count >= I2C_FIFO_FULL_THLD;
 375         else
 376                 i2c_tran = i2c_dev->count;
 377
 378         /*
 379          * If we got one ACK from slave when writing data, and we did not
 380          * finish this transmission (i2c_tran is not zero), then we should
 381          * continue to write data.
 382          *
 383          * For reading data, ack is always true, if i2c_tran is not 0 which
 384          * means we still need to contine to read data from slave.
 385          */
 386         if (i2c_tran && ack) {
 387                 sprd_i2c_data_transfer(i2c_dev);
 388                 return IRQ_HANDLED;
 389         }
 390
 391         i2c_dev->err = 0;
 392
 393         /*
 394          * If we did not get one ACK from slave when writing data, we should
 395          * return -EIO to notify users.
 396          */
 397         if (!ack)
 398                 i2c_dev->err = -EIO;
 399         else if (msg->flags & I2C_M_RD && i2c_dev->count)
 400                 sprd_i2c_read_bytes(i2c_dev, i2c_dev->buf, i2c_dev->count);
 401
 402         /* Transmission is done and clear ack and start operation */
 403         sprd_i2c_clear_ack(i2c_dev);
 404         sprd_i2c_clear_start(i2c_dev);
 405         complete(&i2c_dev->complete);
 406
 407         return IRQ_HANDLED;
 408 }
 409
 410 static irqreturn_t sprd_i2c_isr(int irq, void *dev_id)
 411 {
 412         struct sprd_i2c *i2c_dev = dev_id;
 413         struct i2c_msg *msg = i2c_dev->msg;
 414         bool ack = !(readl(i2c_dev->base + I2C_STATUS) & I2C_RX_ACK);
 415         u32 i2c_tran;
 416
 417         if (msg->flags & I2C_M_RD)
 418                 i2c_tran = i2c_dev->count >= I2C_FIFO_FULL_THLD;
 419         else
 420                 i2c_tran = i2c_dev->count;
 421
 422         /*
 423          * If we did not get one ACK from slave when writing data, then we
 424          * should finish this transmission since we got some errors.
 425          *
 426          * When writing data, if i2c_tran == 0 which means we have writen
 427          * done all data, then we can finish this transmission.
 428          *
 429          * When reading data, if conut < rx fifo full threshold, which
 430          * means we can read all data in one time, then we can finish this
 431          * transmission too.
 432          */
 433         if (!i2c_tran || !ack) {
 434                 sprd_i2c_clear_start(i2c_dev);
 435                 sprd_i2c_clear_irq(i2c_dev);
 436         }
 437
 438         sprd_i2c_set_fifo_empty_int(i2c_dev, 0);
 439         sprd_i2c_set_fifo_full_int(i2c_dev, 0);
 440
 441         return IRQ_WAKE_THREAD;
 442 }
 443
 444 static int sprd_i2c_clk_init(struct sprd_i2c *i2c_dev)
 445 {
 446         struct clk *clk_i2c, *clk_parent;
 447
 448         clk_i2c = devm_clk_get(i2c_dev->dev, "i2c");
 449         if (IS_ERR(clk_i2c)) {
 450                 dev_warn(i2c_dev->dev, "i2c%d can't get the i2c clock\n",
 451                          i2c_dev->adap.nr);
 452                 clk_i2c = NULL;
 453         }
 454
 455         clk_parent = devm_clk_get(i2c_dev->dev, "source");
 456         if (IS_ERR(clk_parent)) {
 457                 dev_warn(i2c_dev->dev, "i2c%d can't get the source clock\n",
 458                          i2c_dev->adap.nr);
 459                 clk_parent = NULL;
 460         }
 461
 462         if (clk_set_parent(clk_i2c, clk_parent))
 463                 i2c_dev->src_clk = clk_get_rate(clk_i2c);
 464         else
 465                 i2c_dev->src_clk = 26000000;
 466
 467         dev_dbg(i2c_dev->dev, "i2c%d set source clock is %d\n",
 468                 i2c_dev->adap.nr, i2c_dev->src_clk);
 469
 470         i2c_dev->clk = devm_clk_get(i2c_dev->dev, "enable");
 471         if (IS_ERR(i2c_dev->clk)) {
 472                 dev_warn(i2c_dev->dev, "i2c%d can't get the enable clock\n",
 473                          i2c_dev->adap.nr);
 474                 i2c_dev->clk = NULL;
 475         }
 476
 477         return 0;
 478 }
 479
 480 static int sprd_i2c_probe(struct platform_device *pdev)
 481 {
 482         struct device *dev = &pdev->dev;
 483         struct sprd_i2c *i2c_dev;
 484         struct resource *res;
 485         u32 prop;
 486         int ret;
 487
 488         pdev->id = of_alias_get_id(dev->of_node, "i2c");
 489
 490         i2c_dev = devm_kzalloc(dev, sizeof(struct sprd_i2c), GFP_KERNEL);
 491         if (!i2c_dev)
 492                 return -ENOMEM;
 493
 494         res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 495         i2c_dev->base = devm_ioremap_resource(dev, res);
 496         if (IS_ERR(i2c_dev->base))
 497                 return PTR_ERR(i2c_dev->base);
 498
 499         i2c_dev->irq = platform_get_irq(pdev, 0);
 500         if (i2c_dev->irq < 0) {
 501                 dev_err(&pdev->dev, "failed to get irq resource\n");
 502                 return i2c_dev->irq;
 503         }
 504
 505         i2c_set_adapdata(&i2c_dev->adap, i2c_dev);
 506         init_completion(&i2c_dev->complete);
 507         snprintf(i2c_dev->adap.name, sizeof(i2c_dev->adap.name),
 508                  "%s", "sprd-i2c");
 509
 510         i2c_dev->bus_freq = 100000;
 511         i2c_dev->adap.owner = THIS_MODULE;
 512         i2c_dev->dev = dev;
 513         i2c_dev->adap.retries = 3;
 514         i2c_dev->adap.algo = &sprd_i2c_algo;
 515         i2c_dev->adap.algo_data = i2c_dev;
 516         i2c_dev->adap.dev.parent = dev;
 517         i2c_dev->adap.nr = pdev->id;
 518         i2c_dev->adap.dev.of_node = dev->of_node;
 519
 520         if (!of_property_read_u32(dev->of_node, "clock-frequency", &prop))
 521                 i2c_dev->bus_freq = prop;
 522
 523         /* We only support 100k and 400k now, otherwise will return error. */
 524         if (i2c_dev->bus_freq != 100000 && i2c_dev->bus_freq != 400000)
 525                 return -EINVAL;
 526
 527         sprd_i2c_clk_init(i2c_dev);
 528         platform_set_drvdata(pdev, i2c_dev);
 529
 530         ret = clk_prepare_enable(i2c_dev->clk);
 531         if (ret)
 532                 return ret;
 533
 534         sprd_i2c_enable(i2c_dev);
 535
 536         pm_runtime_set_autosuspend_delay(i2c_dev->dev, SPRD_I2C_PM_TIMEOUT);
 537         pm_runtime_use_autosuspend(i2c_dev->dev);
 538         pm_runtime_set_active(i2c_dev->dev);
 539         pm_runtime_enable(i2c_dev->dev);
 540
 541         ret = pm_runtime_get_sync(i2c_dev->dev);
 542         if (ret < 0)
 543                 goto err_rpm_put;
 544
 545         ret = devm_request_threaded_irq(dev, i2c_dev->irq,
 546                 sprd_i2c_isr, sprd_i2c_isr_thread,
 547                 IRQF_NO_SUSPEND | IRQF_ONESHOT,
 548                 pdev->name, i2c_dev);
 549         if (ret) {
 550                 dev_err(&pdev->dev, "failed to request irq %d\n", i2c_dev->irq);
 551                 goto err_rpm_put;
 552         }
 553
 554         ret = i2c_add_numbered_adapter(&i2c_dev->adap);
 555         if (ret) {
 556                 dev_err(&pdev->dev, "add adapter failed\n");
 557                 goto err_rpm_put;
 558         }
 559
 560         pm_runtime_mark_last_busy(i2c_dev->dev);
 561         pm_runtime_put_autosuspend(i2c_dev->dev);
 562         return 0;
 563
 564 err_rpm_put:
 565         pm_runtime_put_noidle(i2c_dev->dev);
 566         pm_runtime_disable(i2c_dev->dev);
 567         clk_disable_unprepare(i2c_dev->clk);
 568         return ret;
 569 }
 570
 571 static int sprd_i2c_remove(struct platform_device *pdev)
 572 {
 573         struct sprd_i2c *i2c_dev = platform_get_drvdata(pdev);
 574         int ret;
 575
 576         ret = pm_runtime_get_sync(i2c_dev->dev);
 577         if (ret < 0)
 578                 return ret;
 579
 580         i2c_del_adapter(&i2c_dev->adap);
 581         clk_disable_unprepare(i2c_dev->clk);
 582
 583         pm_runtime_put_noidle(i2c_dev->dev);
 584         pm_runtime_disable(i2c_dev->dev);
 585
 586         return 0;
 587 }
 588
 589 static int __maybe_unused sprd_i2c_suspend_noirq(struct device *pdev)
 590 {
 591         struct sprd_i2c *i2c_dev = dev_get_drvdata(pdev);
 592
 593         i2c_lock_adapter(&i2c_dev->adap);
 594         i2c_dev->is_suspended = true;
 595         i2c_unlock_adapter(&i2c_dev->adap);
 596
 597         return pm_runtime_force_suspend(pdev);
 598 }
 599
 600 static int __maybe_unused sprd_i2c_resume_noirq(struct device *pdev)
 601 {
 602         struct sprd_i2c *i2c_dev = dev_get_drvdata(pdev);
 603
 604         i2c_lock_adapter(&i2c_dev->adap);
 605         i2c_dev->is_suspended = false;
 606         i2c_unlock_adapter(&i2c_dev->adap);
 607
 608         return pm_runtime_force_resume(pdev);
 609 }
 610
 611 static int __maybe_unused sprd_i2c_runtime_suspend(struct device *pdev)
 612 {
 613         struct sprd_i2c *i2c_dev = dev_get_drvdata(pdev);
 614
 615         clk_disable_unprepare(i2c_dev->clk);
 616
 617         return 0;
 618 }
 619
 620 static int __maybe_unused sprd_i2c_runtime_resume(struct device *pdev)
 621 {
 622         struct sprd_i2c *i2c_dev = dev_get_drvdata(pdev);
 623         int ret;
 624
 625         ret = clk_prepare_enable(i2c_dev->clk);
 626         if (ret)
 627                 return ret;
 628
 629         sprd_i2c_enable(i2c_dev);
 630
 631         return 0;
 632 }
 633
 634 static const struct dev_pm_ops sprd_i2c_pm_ops = {
 635         SET_RUNTIME_PM_OPS(sprd_i2c_runtime_suspend,
 636                            sprd_i2c_runtime_resume, NULL)
 637
 638         SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(sprd_i2c_suspend_noirq,
 639                                       sprd_i2c_resume_noirq)
 640 };
 641
 642 static const struct of_device_id sprd_i2c_of_match[] = {
 643         { .compatible = "sprd,sc9860-i2c", },
 644         {},
 645 };
 646
 647 static struct platform_driver sprd_i2c_driver = {
 648         .probe = sprd_i2c_probe,
 649         .remove = sprd_i2c_remove,
 650         .driver = {
 651                    .name = "sprd-i2c",
 652                    .of_match_table = sprd_i2c_of_match,
 653                    .pm = &sprd_i2c_pm_ops,
 654         },
 655 };
 656
 657 static int sprd_i2c_init(void)
 658 {
 659         return platform_driver_register(&sprd_i2c_driver);
 660 }
 661 arch_initcall_sync(sprd_i2c_init);