Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6

[sfrench/cifs-2.6.git] / drivers / gpu / drm / i915 / i915_reg.h

/* Copyright 2003 Tungsten Graphics, Inc., Cedar Park, Texas.
 * All Rights Reserved.
 *
 * Permission is hereby granted, free of charge, to any person obtaining a
 * copy of this software and associated documentation files (the
 * "Software"), to deal in the Software without restriction, including
 * without limitation the rights to use, copy, modify, merge, publish,
 * distribute, sub license, and/or sell copies of the Software, and to
 * permit persons to whom the Software is furnished to do so, subject to
 * the following conditions:
 *
 * The above copyright notice and this permission notice (including the
 * next paragraph) shall be included in all copies or substantial portions
 * of the Software.
 *
 * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS
 * OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
 * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT.
 * IN NO EVENT SHALL TUNGSTEN GRAPHICS AND/OR ITS SUPPLIERS BE LIABLE FOR
 * ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT,
 * TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE
 * SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
 */

#ifndef _I915_REG_H_
#define _I915_REG_H_

/*
 * The Bridge device's PCI config space has information about the
 * fb aperture size and the amount of pre-reserved memory.
 */
#define INTEL_GMCH_CTRL         0x52
#define INTEL_GMCH_VGA_DISABLE  (1 << 1)
#define INTEL_GMCH_ENABLED      0x4
#define INTEL_GMCH_MEM_MASK     0x1
#define INTEL_GMCH_MEM_64M      0x1
#define INTEL_GMCH_MEM_128M     0

#define INTEL_GMCH_GMS_MASK             (0xf << 4)
#define INTEL_855_GMCH_GMS_DISABLED     (0x0 << 4)
#define INTEL_855_GMCH_GMS_STOLEN_1M    (0x1 << 4)
#define INTEL_855_GMCH_GMS_STOLEN_4M    (0x2 << 4)
#define INTEL_855_GMCH_GMS_STOLEN_8M    (0x3 << 4)
#define INTEL_855_GMCH_GMS_STOLEN_16M   (0x4 << 4)
#define INTEL_855_GMCH_GMS_STOLEN_32M   (0x5 << 4)

#define INTEL_915G_GMCH_GMS_STOLEN_48M  (0x6 << 4)
#define INTEL_915G_GMCH_GMS_STOLEN_64M  (0x7 << 4)
#define INTEL_GMCH_GMS_STOLEN_128M      (0x8 << 4)
#define INTEL_GMCH_GMS_STOLEN_256M      (0x9 << 4)
#define INTEL_GMCH_GMS_STOLEN_96M       (0xa << 4)
#define INTEL_GMCH_GMS_STOLEN_160M      (0xb << 4)
#define INTEL_GMCH_GMS_STOLEN_224M      (0xc << 4)
#define INTEL_GMCH_GMS_STOLEN_352M      (0xd << 4)

/* PCI config space */

#define HPLLCC  0xc0 /* 855 only */
#define   GC_CLOCK_CONTROL_MASK         (0xf << 0)
#define   GC_CLOCK_133_200              (0 << 0)
#define   GC_CLOCK_100_200              (1 << 0)
#define   GC_CLOCK_100_133              (2 << 0)
#define   GC_CLOCK_166_250              (3 << 0)
#define GCFGC   0xf0 /* 915+ only */
#define   GC_LOW_FREQUENCY_ENABLE       (1 << 7)
#define   GC_DISPLAY_CLOCK_190_200_MHZ  (0 << 4)
#define   GC_DISPLAY_CLOCK_333_MHZ      (4 << 4)
#define   GC_DISPLAY_CLOCK_MASK         (7 << 4)
#define   GM45_GC_RENDER_CLOCK_MASK     (0xf << 0)
#define   GM45_GC_RENDER_CLOCK_266_MHZ  (8 << 0)
#define   GM45_GC_RENDER_CLOCK_320_MHZ  (9 << 0)
#define   GM45_GC_RENDER_CLOCK_400_MHZ  (0xb << 0)
#define   GM45_GC_RENDER_CLOCK_533_MHZ  (0xc << 0)
#define   I965_GC_RENDER_CLOCK_MASK     (0xf << 0)
#define   I965_GC_RENDER_CLOCK_267_MHZ  (2 << 0)
#define   I965_GC_RENDER_CLOCK_333_MHZ  (3 << 0)
#define   I965_GC_RENDER_CLOCK_444_MHZ  (4 << 0)
#define   I965_GC_RENDER_CLOCK_533_MHZ  (5 << 0)
#define   I945_GC_RENDER_CLOCK_MASK     (7 << 0)
#define   I945_GC_RENDER_CLOCK_166_MHZ  (0 << 0)
#define   I945_GC_RENDER_CLOCK_200_MHZ  (1 << 0)
#define   I945_GC_RENDER_CLOCK_250_MHZ  (3 << 0)
#define   I945_GC_RENDER_CLOCK_400_MHZ  (5 << 0)
#define   I915_GC_RENDER_CLOCK_MASK     (7 << 0)
#define   I915_GC_RENDER_CLOCK_166_MHZ  (0 << 0)
#define   I915_GC_RENDER_CLOCK_200_MHZ  (1 << 0)
#define   I915_GC_RENDER_CLOCK_333_MHZ  (4 << 0)
#define LBB     0xf4
#define GDRST 0xc0
#define  GDRST_FULL     (0<<2)
#define  GDRST_RENDER   (1<<2)
#define  GDRST_MEDIA    (3<<2)

/* VGA stuff */

#define VGA_ST01_MDA 0x3ba
#define VGA_ST01_CGA 0x3da

#define VGA_MSR_WRITE 0x3c2
#define VGA_MSR_READ 0x3cc
#define   VGA_MSR_MEM_EN (1<<1)
#define   VGA_MSR_CGA_MODE (1<<0)

#define VGA_SR_INDEX 0x3c4
#define VGA_SR_DATA 0x3c5

#define VGA_AR_INDEX 0x3c0
#define   VGA_AR_VID_EN (1<<5)
#define VGA_AR_DATA_WRITE 0x3c0
#define VGA_AR_DATA_READ 0x3c1

#define VGA_GR_INDEX 0x3ce
#define VGA_GR_DATA 0x3cf
/* GR05 */
#define   VGA_GR_MEM_READ_MODE_SHIFT 3
#define     VGA_GR_MEM_READ_MODE_PLANE 1
/* GR06 */
#define   VGA_GR_MEM_MODE_MASK 0xc
#define   VGA_GR_MEM_MODE_SHIFT 2
#define   VGA_GR_MEM_A0000_AFFFF 0
#define   VGA_GR_MEM_A0000_BFFFF 1
#define   VGA_GR_MEM_B0000_B7FFF 2
#define   VGA_GR_MEM_B0000_BFFFF 3

#define VGA_DACMASK 0x3c6
#define VGA_DACRX 0x3c7
#define VGA_DACWX 0x3c8
#define VGA_DACDATA 0x3c9

#define VGA_CR_INDEX_MDA 0x3b4
#define VGA_CR_DATA_MDA 0x3b5
#define VGA_CR_INDEX_CGA 0x3d4
#define VGA_CR_DATA_CGA 0x3d5

/*
 * Memory interface instructions used by the kernel
 */
#define MI_INSTR(opcode, flags) (((opcode) << 23) | (flags))

#define MI_NOOP                 MI_INSTR(0, 0)
#define MI_USER_INTERRUPT       MI_INSTR(0x02, 0)
#define MI_WAIT_FOR_EVENT       MI_INSTR(0x03, 0)
#define   MI_WAIT_FOR_PLANE_B_FLIP      (1<<6)
#define   MI_WAIT_FOR_PLANE_A_FLIP      (1<<2)
#define   MI_WAIT_FOR_PLANE_A_SCANLINES (1<<1)
#define MI_FLUSH                MI_INSTR(0x04, 0)
#define   MI_READ_FLUSH         (1 << 0)
#define   MI_EXE_FLUSH          (1 << 1)
#define   MI_NO_WRITE_FLUSH     (1 << 2)
#define   MI_SCENE_COUNT        (1 << 3) /* just increment scene count */
#define   MI_END_SCENE          (1 << 4) /* flush binner and incr scene count */
#define MI_BATCH_BUFFER_END     MI_INSTR(0x0a, 0)
#define MI_REPORT_HEAD          MI_INSTR(0x07, 0)
#define MI_LOAD_SCAN_LINES_INCL MI_INSTR(0x12, 0)
#define MI_STORE_DWORD_IMM      MI_INSTR(0x20, 1)
#define   MI_MEM_VIRTUAL        (1 << 22) /* 965+ only */
#define MI_STORE_DWORD_INDEX    MI_INSTR(0x21, 1)
#define   MI_STORE_DWORD_INDEX_SHIFT 2
#define MI_LOAD_REGISTER_IMM    MI_INSTR(0x22, 1)
#define MI_BATCH_BUFFER         MI_INSTR(0x30, 1)
#define   MI_BATCH_NON_SECURE   (1)
#define   MI_BATCH_NON_SECURE_I965 (1<<8)
#define MI_BATCH_BUFFER_START   MI_INSTR(0x31, 0)

/*
 * 3D instructions used by the kernel
 */
#define GFX_INSTR(opcode, flags) ((0x3 << 29) | ((opcode) << 24) | (flags))

#define GFX_OP_RASTER_RULES    ((0x3<<29)|(0x7<<24))
#define GFX_OP_SCISSOR         ((0x3<<29)|(0x1c<<24)|(0x10<<19))
#define   SC_UPDATE_SCISSOR       (0x1<<1)
#define   SC_ENABLE_MASK          (0x1<<0)
#define   SC_ENABLE               (0x1<<0)
#define GFX_OP_LOAD_INDIRECT   ((0x3<<29)|(0x1d<<24)|(0x7<<16))
#define GFX_OP_SCISSOR_INFO    ((0x3<<29)|(0x1d<<24)|(0x81<<16)|(0x1))
#define   SCI_YMIN_MASK      (0xffff<<16)
#define   SCI_XMIN_MASK      (0xffff<<0)
#define   SCI_YMAX_MASK      (0xffff<<16)
#define   SCI_XMAX_MASK      (0xffff<<0)
#define GFX_OP_SCISSOR_ENABLE    ((0x3<<29)|(0x1c<<24)|(0x10<<19))
#define GFX_OP_SCISSOR_RECT      ((0x3<<29)|(0x1d<<24)|(0x81<<16)|1)
#define GFX_OP_COLOR_FACTOR      ((0x3<<29)|(0x1d<<24)|(0x1<<16)|0x0)
#define GFX_OP_STIPPLE           ((0x3<<29)|(0x1d<<24)|(0x83<<16))
#define GFX_OP_MAP_INFO          ((0x3<<29)|(0x1d<<24)|0x4)
#define GFX_OP_DESTBUFFER_VARS   ((0x3<<29)|(0x1d<<24)|(0x85<<16)|0x0)
#define GFX_OP_DESTBUFFER_INFO   ((0x3<<29)|(0x1d<<24)|(0x8e<<16)|1)
#define GFX_OP_DRAWRECT_INFO     ((0x3<<29)|(0x1d<<24)|(0x80<<16)|(0x3))
#define GFX_OP_DRAWRECT_INFO_I965  ((0x7900<<16)|0x2)
#define SRC_COPY_BLT_CMD                ((2<<29)|(0x43<<22)|4)
#define XY_SRC_COPY_BLT_CMD             ((2<<29)|(0x53<<22)|6)
#define XY_MONO_SRC_COPY_IMM_BLT        ((2<<29)|(0x71<<22)|5)
#define XY_SRC_COPY_BLT_WRITE_ALPHA     (1<<21)
#define XY_SRC_COPY_BLT_WRITE_RGB       (1<<20)
#define   BLT_DEPTH_8                   (0<<24)
#define   BLT_DEPTH_16_565              (1<<24)
#define   BLT_DEPTH_16_1555             (2<<24)
#define   BLT_DEPTH_32                  (3<<24)
#define   BLT_ROP_GXCOPY                (0xcc<<16)
#define XY_SRC_COPY_BLT_SRC_TILED       (1<<15) /* 965+ only */
#define XY_SRC_COPY_BLT_DST_TILED       (1<<11) /* 965+ only */
#define CMD_OP_DISPLAYBUFFER_INFO ((0x0<<29)|(0x14<<23)|2)
#define   ASYNC_FLIP                (1<<22)
#define   DISPLAY_PLANE_A           (0<<20)
#define   DISPLAY_PLANE_B           (1<<20)

/*
 * Fence registers
 */
#define FENCE_REG_830_0                 0x2000
#define FENCE_REG_945_8                 0x3000
#define   I830_FENCE_START_MASK         0x07f80000
#define   I830_FENCE_TILING_Y_SHIFT     12
#define   I830_FENCE_SIZE_BITS(size)    ((ffs((size) >> 19) - 1) << 8)
#define   I830_FENCE_PITCH_SHIFT        4
#define   I830_FENCE_REG_VALID          (1<<0)
#define   I915_FENCE_MAX_PITCH_VAL      0x10
#define   I830_FENCE_MAX_PITCH_VAL      6
#define   I830_FENCE_MAX_SIZE_VAL       (1<<8)

#define   I915_FENCE_START_MASK         0x0ff00000
#define   I915_FENCE_SIZE_BITS(size)    ((ffs((size) >> 20) - 1) << 8)

#define FENCE_REG_965_0                 0x03000
#define   I965_FENCE_PITCH_SHIFT        2
#define   I965_FENCE_TILING_Y_SHIFT     1
#define   I965_FENCE_REG_VALID          (1<<0)
#define   I965_FENCE_MAX_PITCH_VAL      0x0400

/*
 * Instruction and interrupt control regs
 */
#define PGTBL_ER        0x02024
#define PRB0_TAIL       0x02030
#define PRB0_HEAD       0x02034
#define PRB0_START      0x02038
#define PRB0_CTL        0x0203c
#define   TAIL_ADDR             0x001FFFF8
#define   HEAD_WRAP_COUNT       0xFFE00000
#define   HEAD_WRAP_ONE         0x00200000
#define   HEAD_ADDR             0x001FFFFC
#define   RING_NR_PAGES         0x001FF000
#define   RING_REPORT_MASK      0x00000006
#define   RING_REPORT_64K       0x00000002
#define   RING_REPORT_128K      0x00000004
#define   RING_NO_REPORT        0x00000000
#define   RING_VALID_MASK       0x00000001
#define   RING_VALID            0x00000001
#define   RING_INVALID          0x00000000
#define PRB1_TAIL       0x02040 /* 915+ only */
#define PRB1_HEAD       0x02044 /* 915+ only */
#define PRB1_START      0x02048 /* 915+ only */
#define PRB1_CTL        0x0204c /* 915+ only */
#define IPEIR_I965      0x02064
#define IPEHR_I965      0x02068
#define INSTDONE_I965   0x0206c
#define INSTPS          0x02070 /* 965+ only */
#define INSTDONE1       0x0207c /* 965+ only */
#define ACTHD_I965      0x02074
#define HWS_PGA         0x02080
#define HWS_ADDRESS_MASK        0xfffff000
#define HWS_START_ADDRESS_SHIFT 4
#define IPEIR           0x02088
#define IPEHR           0x0208c
#define INSTDONE        0x02090
#define NOPID           0x02094
#define HWSTAM          0x02098
#define SCPD0           0x0209c /* 915+ only */
#define IER             0x020a0
#define IIR             0x020a4
#define IMR             0x020a8
#define ISR             0x020ac
#define   I915_PIPE_CONTROL_NOTIFY_INTERRUPT            (1<<18)
#define   I915_DISPLAY_PORT_INTERRUPT                   (1<<17)
#define   I915_RENDER_COMMAND_PARSER_ERROR_INTERRUPT    (1<<15)
#define   I915_GMCH_THERMAL_SENSOR_EVENT_INTERRUPT      (1<<14)
#define   I915_HWB_OOM_INTERRUPT                        (1<<13)
#define   I915_SYNC_STATUS_INTERRUPT                    (1<<12)
#define   I915_DISPLAY_PLANE_A_FLIP_PENDING_INTERRUPT   (1<<11)
#define   I915_DISPLAY_PLANE_B_FLIP_PENDING_INTERRUPT   (1<<10)
#define   I915_OVERLAY_PLANE_FLIP_PENDING_INTERRUPT     (1<<9)
#define   I915_DISPLAY_PLANE_C_FLIP_PENDING_INTERRUPT   (1<<8)
#define   I915_DISPLAY_PIPE_A_VBLANK_INTERRUPT          (1<<7)
#define   I915_DISPLAY_PIPE_A_EVENT_INTERRUPT           (1<<6)
#define   I915_DISPLAY_PIPE_B_VBLANK_INTERRUPT          (1<<5)
#define   I915_DISPLAY_PIPE_B_EVENT_INTERRUPT           (1<<4)
#define   I915_DEBUG_INTERRUPT                          (1<<2)
#define   I915_USER_INTERRUPT                           (1<<1)
#define   I915_ASLE_INTERRUPT                           (1<<0)
#define EIR             0x020b0
#define EMR             0x020b4
#define ESR             0x020b8
#define   GM45_ERROR_PAGE_TABLE                         (1<<5)
#define   GM45_ERROR_MEM_PRIV                           (1<<4)
#define   I915_ERROR_PAGE_TABLE                         (1<<4)
#define   GM45_ERROR_CP_PRIV                            (1<<3)
#define   I915_ERROR_MEMORY_REFRESH                     (1<<1)
#define   I915_ERROR_INSTRUCTION                        (1<<0)
#define INSTPM          0x020c0
#define ACTHD           0x020c8
#define FW_BLC          0x020d8
#define FW_BLC2         0x020dc
#define FW_BLC_SELF     0x020e0 /* 915+ only */
#define   FW_BLC_SELF_EN (1<<15)
#define MM_BURST_LENGTH     0x00700000
#define MM_FIFO_WATERMARK   0x0001F000
#define LM_BURST_LENGTH     0x00000700
#define LM_FIFO_WATERMARK   0x0000001F
#define MI_ARB_STATE    0x020e4 /* 915+ only */
#define CACHE_MODE_0    0x02120 /* 915+ only */
#define   CM0_MASK_SHIFT          16
#define   CM0_IZ_OPT_DISABLE      (1<<6)
#define   CM0_ZR_OPT_DISABLE      (1<<5)
#define   CM0_DEPTH_EVICT_DISABLE (1<<4)
#define   CM0_COLOR_EVICT_DISABLE (1<<3)
#define   CM0_DEPTH_WRITE_DISABLE (1<<1)
#define   CM0_RC_OP_FLUSH_DISABLE (1<<0)
#define GFX_FLSH_CNTL   0x02170 /* 915+ only */


/*
 * Framebuffer compression (915+ only)
 */

#define FBC_CFB_BASE            0x03200 /* 4k page aligned */
#define FBC_LL_BASE             0x03204 /* 4k page aligned */
#define FBC_CONTROL             0x03208
#define   FBC_CTL_EN            (1<<31)
#define   FBC_CTL_PERIODIC      (1<<30)
#define   FBC_CTL_INTERVAL_SHIFT (16)
#define   FBC_CTL_UNCOMPRESSIBLE (1<<14)
#define   FBC_CTL_STRIDE_SHIFT  (5)
#define   FBC_CTL_FENCENO       (1<<0)
#define FBC_COMMAND             0x0320c
#define   FBC_CMD_COMPRESS      (1<<0)
#define FBC_STATUS              0x03210
#define   FBC_STAT_COMPRESSING  (1<<31)
#define   FBC_STAT_COMPRESSED   (1<<30)
#define   FBC_STAT_MODIFIED     (1<<29)
#define   FBC_STAT_CURRENT_LINE (1<<0)
#define FBC_CONTROL2            0x03214
#define   FBC_CTL_FENCE_DBL     (0<<4)
#define   FBC_CTL_IDLE_IMM      (0<<2)
#define   FBC_CTL_IDLE_FULL     (1<<2)
#define   FBC_CTL_IDLE_LINE     (2<<2)
#define   FBC_CTL_IDLE_DEBUG    (3<<2)
#define   FBC_CTL_CPU_FENCE     (1<<1)
#define   FBC_CTL_PLANEA        (0<<0)
#define   FBC_CTL_PLANEB        (1<<0)
#define FBC_FENCE_OFF           0x0321b
#define FBC_TAG                 0x03300

#define FBC_LL_SIZE             (1536)

/* Framebuffer compression for GM45+ */
#define DPFC_CB_BASE            0x3200
#define DPFC_CONTROL            0x3208
#define   DPFC_CTL_EN           (1<<31)
#define   DPFC_CTL_PLANEA       (0<<30)
#define   DPFC_CTL_PLANEB       (1<<30)
#define   DPFC_CTL_FENCE_EN     (1<<29)
#define   DPFC_SR_EN            (1<<10)
#define   DPFC_CTL_LIMIT_1X     (0<<6)
#define   DPFC_CTL_LIMIT_2X     (1<<6)
#define   DPFC_CTL_LIMIT_4X     (2<<6)
#define DPFC_RECOMP_CTL         0x320c
#define   DPFC_RECOMP_STALL_EN  (1<<27)
#define   DPFC_RECOMP_STALL_WM_SHIFT (16)
#define   DPFC_RECOMP_STALL_WM_MASK (0x07ff0000)
#define   DPFC_RECOMP_TIMER_COUNT_SHIFT (0)
#define   DPFC_RECOMP_TIMER_COUNT_MASK (0x0000003f)
#define DPFC_STATUS             0x3210
#define   DPFC_INVAL_SEG_SHIFT  (16)
#define   DPFC_INVAL_SEG_MASK   (0x07ff0000)
#define   DPFC_COMP_SEG_SHIFT   (0)
#define   DPFC_COMP_SEG_MASK    (0x000003ff)
#define DPFC_STATUS2            0x3214
#define DPFC_FENCE_YOFF         0x3218
#define DPFC_CHICKEN            0x3224
#define   DPFC_HT_MODIFY        (1<<31)

/*
 * GPIO regs
 */
#define GPIOA                   0x5010
#define GPIOB                   0x5014
#define GPIOC                   0x5018
#define GPIOD                   0x501c
#define GPIOE                   0x5020
#define GPIOF                   0x5024
#define GPIOG                   0x5028
#define GPIOH                   0x502c
# define GPIO_CLOCK_DIR_MASK            (1 << 0)
# define GPIO_CLOCK_DIR_IN              (0 << 1)
# define GPIO_CLOCK_DIR_OUT             (1 << 1)
# define GPIO_CLOCK_VAL_MASK            (1 << 2)
# define GPIO_CLOCK_VAL_OUT             (1 << 3)
# define GPIO_CLOCK_VAL_IN              (1 << 4)
# define GPIO_CLOCK_PULLUP_DISABLE      (1 << 5)
# define GPIO_DATA_DIR_MASK             (1 << 8)
# define GPIO_DATA_DIR_IN               (0 << 9)
# define GPIO_DATA_DIR_OUT              (1 << 9)
# define GPIO_DATA_VAL_MASK             (1 << 10)
# define GPIO_DATA_VAL_OUT              (1 << 11)
# define GPIO_DATA_VAL_IN               (1 << 12)
# define GPIO_DATA_PULLUP_DISABLE       (1 << 13)

/*
 * Clock control & power management
 */

#define VGA0    0x6000
#define VGA1    0x6004
#define VGA_PD  0x6010
#define   VGA0_PD_P2_DIV_4      (1 << 7)
#define   VGA0_PD_P1_DIV_2      (1 << 5)
#define   VGA0_PD_P1_SHIFT      0
#define   VGA0_PD_P1_MASK       (0x1f << 0)
#define   VGA1_PD_P2_DIV_4      (1 << 15)
#define   VGA1_PD_P1_DIV_2      (1 << 13)
#define   VGA1_PD_P1_SHIFT      8
#define   VGA1_PD_P1_MASK       (0x1f << 8)
#define DPLL_A  0x06014
#define DPLL_B  0x06018
#define   DPLL_VCO_ENABLE               (1 << 31)
#define   DPLL_DVO_HIGH_SPEED           (1 << 30)
#define   DPLL_SYNCLOCK_ENABLE          (1 << 29)
#define   DPLL_VGA_MODE_DIS             (1 << 28)
#define   DPLLB_MODE_DAC_SERIAL         (1 << 26) /* i915 */
#define   DPLLB_MODE_LVDS               (2 << 26) /* i915 */
#define   DPLL_MODE_MASK                (3 << 26)
#define   DPLL_DAC_SERIAL_P2_CLOCK_DIV_10 (0 << 24) /* i915 */
#define   DPLL_DAC_SERIAL_P2_CLOCK_DIV_5 (1 << 24) /* i915 */
#define   DPLLB_LVDS_P2_CLOCK_DIV_14    (0 << 24) /* i915 */
#define   DPLLB_LVDS_P2_CLOCK_DIV_7     (1 << 24) /* i915 */
#define   DPLL_P2_CLOCK_DIV_MASK        0x03000000 /* i915 */
#define   DPLL_FPA01_P1_POST_DIV_MASK   0x00ff0000 /* i915 */
#define   DPLL_FPA01_P1_POST_DIV_MASK_IGD       0x00ff8000 /* IGD */

#define I915_FIFO_UNDERRUN_STATUS               (1UL<<31)
#define I915_CRC_ERROR_ENABLE                   (1UL<<29)
#define I915_CRC_DONE_ENABLE                    (1UL<<28)
#define I915_GMBUS_EVENT_ENABLE                 (1UL<<27)
#define I915_VSYNC_INTERRUPT_ENABLE             (1UL<<25)
#define I915_DISPLAY_LINE_COMPARE_ENABLE        (1UL<<24)
#define I915_DPST_EVENT_ENABLE                  (1UL<<23)
#define I915_LEGACY_BLC_EVENT_ENABLE            (1UL<<22)
#define I915_ODD_FIELD_INTERRUPT_ENABLE         (1UL<<21)
#define I915_EVEN_FIELD_INTERRUPT_ENABLE        (1UL<<20)
#define I915_START_VBLANK_INTERRUPT_ENABLE      (1UL<<18)       /* 965 or later */
#define I915_VBLANK_INTERRUPT_ENABLE            (1UL<<17)
#define I915_OVERLAY_UPDATED_ENABLE             (1UL<<16)
#define I915_CRC_ERROR_INTERRUPT_STATUS         (1UL<<13)
#define I915_CRC_DONE_INTERRUPT_STATUS          (1UL<<12)
#define I915_GMBUS_INTERRUPT_STATUS             (1UL<<11)
#define I915_VSYNC_INTERRUPT_STATUS             (1UL<<9)
#define I915_DISPLAY_LINE_COMPARE_STATUS        (1UL<<8)
#define I915_DPST_EVENT_STATUS                  (1UL<<7)
#define I915_LEGACY_BLC_EVENT_STATUS            (1UL<<6)
#define I915_ODD_FIELD_INTERRUPT_STATUS         (1UL<<5)
#define I915_EVEN_FIELD_INTERRUPT_STATUS        (1UL<<4)
#define I915_START_VBLANK_INTERRUPT_STATUS      (1UL<<2)        /* 965 or later */
#define I915_VBLANK_INTERRUPT_STATUS            (1UL<<1)
#define I915_OVERLAY_UPDATED_STATUS             (1UL<<0)

#define SRX_INDEX               0x3c4
#define SRX_DATA                0x3c5
#define SR01                    1
#define SR01_SCREEN_OFF         (1<<5)

#define PPCR                    0x61204
#define PPCR_ON                 (1<<0)

#define DVOB                    0x61140
#define DVOB_ON                 (1<<31)
#define DVOC                    0x61160
#define DVOC_ON                 (1<<31)
#define LVDS                    0x61180
#define LVDS_ON                 (1<<31)

#define ADPA                    0x61100
#define ADPA_DPMS_MASK          (~(3<<10))
#define ADPA_DPMS_ON            (0<<10)
#define ADPA_DPMS_SUSPEND       (1<<10)
#define ADPA_DPMS_STANDBY       (2<<10)
#define ADPA_DPMS_OFF           (3<<10)

#define RING_TAIL               0x00
#define TAIL_ADDR               0x001FFFF8
#define RING_HEAD               0x04
#define HEAD_WRAP_COUNT         0xFFE00000
#define HEAD_WRAP_ONE           0x00200000
#define HEAD_ADDR               0x001FFFFC
#define RING_START              0x08
#define START_ADDR              0xFFFFF000
#define RING_LEN                0x0C
#define RING_NR_PAGES           0x001FF000
#define RING_REPORT_MASK        0x00000006
#define RING_REPORT_64K         0x00000002
#define RING_REPORT_128K        0x00000004
#define RING_NO_REPORT          0x00000000
#define RING_VALID_MASK         0x00000001
#define RING_VALID              0x00000001
#define RING_INVALID            0x00000000

/* Scratch pad debug 0 reg:
 */
#define   DPLL_FPA01_P1_POST_DIV_MASK_I830      0x001f0000
/*
 * The i830 generation, in LVDS mode, defines P1 as the bit number set within
 * this field (only one bit may be set).
 */
#define   DPLL_FPA01_P1_POST_DIV_MASK_I830_LVDS 0x003f0000
#define   DPLL_FPA01_P1_POST_DIV_SHIFT  16
#define   DPLL_FPA01_P1_POST_DIV_SHIFT_IGD 15
/* i830, required in DVO non-gang */
#define   PLL_P2_DIVIDE_BY_4            (1 << 23)
#define   PLL_P1_DIVIDE_BY_TWO          (1 << 21) /* i830 */
#define   PLL_REF_INPUT_DREFCLK         (0 << 13)
#define   PLL_REF_INPUT_TVCLKINA        (1 << 13) /* i830 */
#define   PLL_REF_INPUT_TVCLKINBC       (2 << 13) /* SDVO TVCLKIN */
#define   PLLB_REF_INPUT_SPREADSPECTRUMIN (3 << 13)
#define   PLL_REF_INPUT_MASK            (3 << 13)
#define   PLL_LOAD_PULSE_PHASE_SHIFT            9
/* IGDNG */
# define PLL_REF_SDVO_HDMI_MULTIPLIER_SHIFT     9
# define PLL_REF_SDVO_HDMI_MULTIPLIER_MASK      (7 << 9)
# define PLL_REF_SDVO_HDMI_MULTIPLIER(x)        (((x)-1) << 9)
# define DPLL_FPA1_P1_POST_DIV_SHIFT            0
# define DPLL_FPA1_P1_POST_DIV_MASK             0xff

/*
 * Parallel to Serial Load Pulse phase selection.
 * Selects the phase for the 10X DPLL clock for the PCIe
 * digital display port. The range is 4 to 13; 10 or more
 * is just a flip delay. The default is 6
 */
#define   PLL_LOAD_PULSE_PHASE_MASK             (0xf << PLL_LOAD_PULSE_PHASE_SHIFT)
#define   DISPLAY_RATE_SELECT_FPA1              (1 << 8)
/*
 * SDVO multiplier for 945G/GM. Not used on 965.
 */
#define   SDVO_MULTIPLIER_MASK                  0x000000ff
#define   SDVO_MULTIPLIER_SHIFT_HIRES           4
#define   SDVO_MULTIPLIER_SHIFT_VGA             0
#define DPLL_A_MD 0x0601c /* 965+ only */
/*
 * UDI pixel divider, controlling how many pixels are stuffed into a packet.
 *
 * Value is pixels minus 1.  Must be set to 1 pixel for SDVO.
 */
#define   DPLL_MD_UDI_DIVIDER_MASK              0x3f000000
#define   DPLL_MD_UDI_DIVIDER_SHIFT             24
/* UDI pixel divider for VGA, same as DPLL_MD_UDI_DIVIDER_MASK. */
#define   DPLL_MD_VGA_UDI_DIVIDER_MASK          0x003f0000
#define   DPLL_MD_VGA_UDI_DIVIDER_SHIFT         16
/*
 * SDVO/UDI pixel multiplier.
 *
 * SDVO requires that the bus clock rate be between 1 and 2 Ghz, and the bus
 * clock rate is 10 times the DPLL clock.  At low resolution/refresh rate
 * modes, the bus rate would be below the limits, so SDVO allows for stuffing
 * dummy bytes in the datastream at an increased clock rate, with both sides of
 * the link knowing how many bytes are fill.
 *
 * So, for a mode with a dotclock of 65Mhz, we would want to double the clock
 * rate to 130Mhz to get a bus rate of 1.30Ghz.  The DPLL clock rate would be
 * set to 130Mhz, and the SDVO multiplier set to 2x in this register and
 * through an SDVO command.
 *
 * This register field has values of multiplication factor minus 1, with
 * a maximum multiplier of 5 for SDVO.
 */
#define   DPLL_MD_UDI_MULTIPLIER_MASK           0x00003f00
#define   DPLL_MD_UDI_MULTIPLIER_SHIFT          8
/*
 * SDVO/UDI pixel multiplier for VGA, same as DPLL_MD_UDI_MULTIPLIER_MASK.
 * This best be set to the default value (3) or the CRT won't work. No,
 * I don't entirely understand what this does...
 */
#define   DPLL_MD_VGA_UDI_MULTIPLIER_MASK       0x0000003f
#define   DPLL_MD_VGA_UDI_MULTIPLIER_SHIFT      0
#define DPLL_B_MD 0x06020 /* 965+ only */
#define FPA0    0x06040
#define FPA1    0x06044
#define FPB0    0x06048
#define FPB1    0x0604c
#define   FP_N_DIV_MASK         0x003f0000
#define   FP_N_IGD_DIV_MASK     0x00ff0000
#define   FP_N_DIV_SHIFT                16
#define   FP_M1_DIV_MASK        0x00003f00
#define   FP_M1_DIV_SHIFT                8
#define   FP_M2_DIV_MASK        0x0000003f
#define   FP_M2_IGD_DIV_MASK    0x000000ff
#define   FP_M2_DIV_SHIFT                0
#define DPLL_TEST       0x606c
#define   DPLLB_TEST_SDVO_DIV_1         (0 << 22)
#define   DPLLB_TEST_SDVO_DIV_2         (1 << 22)
#define   DPLLB_TEST_SDVO_DIV_4         (2 << 22)
#define   DPLLB_TEST_SDVO_DIV_MASK      (3 << 22)
#define   DPLLB_TEST_N_BYPASS           (1 << 19)
#define   DPLLB_TEST_M_BYPASS           (1 << 18)
#define   DPLLB_INPUT_BUFFER_ENABLE     (1 << 16)
#define   DPLLA_TEST_N_BYPASS           (1 << 3)
#define   DPLLA_TEST_M_BYPASS           (1 << 2)
#define   DPLLA_INPUT_BUFFER_ENABLE     (1 << 0)
#define D_STATE         0x6104
#define  DSTATE_PLL_D3_OFF                      (1<<3)
#define  DSTATE_GFX_CLOCK_GATING                (1<<1)
#define  DSTATE_DOT_CLOCK_GATING                (1<<0)
#define DSPCLK_GATE_D           0x6200
# define DPUNIT_B_CLOCK_GATE_DISABLE            (1 << 30) /* 965 */
# define VSUNIT_CLOCK_GATE_DISABLE              (1 << 29) /* 965 */
# define VRHUNIT_CLOCK_GATE_DISABLE             (1 << 28) /* 965 */
# define VRDUNIT_CLOCK_GATE_DISABLE             (1 << 27) /* 965 */
# define AUDUNIT_CLOCK_GATE_DISABLE             (1 << 26) /* 965 */
# define DPUNIT_A_CLOCK_GATE_DISABLE            (1 << 25) /* 965 */
# define DPCUNIT_CLOCK_GATE_DISABLE             (1 << 24) /* 965 */
# define TVRUNIT_CLOCK_GATE_DISABLE             (1 << 23) /* 915-945 */
# define TVCUNIT_CLOCK_GATE_DISABLE             (1 << 22) /* 915-945 */
# define TVFUNIT_CLOCK_GATE_DISABLE             (1 << 21) /* 915-945 */
# define TVEUNIT_CLOCK_GATE_DISABLE             (1 << 20) /* 915-945 */
# define DVSUNIT_CLOCK_GATE_DISABLE             (1 << 19) /* 915-945 */
# define DSSUNIT_CLOCK_GATE_DISABLE             (1 << 18) /* 915-945 */
# define DDBUNIT_CLOCK_GATE_DISABLE             (1 << 17) /* 915-945 */
# define DPRUNIT_CLOCK_GATE_DISABLE             (1 << 16) /* 915-945 */
# define DPFUNIT_CLOCK_GATE_DISABLE             (1 << 15) /* 915-945 */
# define DPBMUNIT_CLOCK_GATE_DISABLE            (1 << 14) /* 915-945 */
# define DPLSUNIT_CLOCK_GATE_DISABLE            (1 << 13) /* 915-945 */
# define DPLUNIT_CLOCK_GATE_DISABLE             (1 << 12) /* 915-945 */
# define DPOUNIT_CLOCK_GATE_DISABLE             (1 << 11)
# define DPBUNIT_CLOCK_GATE_DISABLE             (1 << 10)
# define DCUNIT_CLOCK_GATE_DISABLE              (1 << 9)
# define DPUNIT_CLOCK_GATE_DISABLE              (1 << 8)
# define VRUNIT_CLOCK_GATE_DISABLE              (1 << 7) /* 915+: reserved */
# define OVHUNIT_CLOCK_GATE_DISABLE             (1 << 6) /* 830-865 */
# define DPIOUNIT_CLOCK_GATE_DISABLE            (1 << 6) /* 915-945 */
# define OVFUNIT_CLOCK_GATE_DISABLE             (1 << 5)
# define OVBUNIT_CLOCK_GATE_DISABLE             (1 << 4)
/**
 * This bit must be set on the 830 to prevent hangs when turning off the
 * overlay scaler.
 */
# define OVRUNIT_CLOCK_GATE_DISABLE             (1 << 3)
# define OVCUNIT_CLOCK_GATE_DISABLE             (1 << 2)
# define OVUUNIT_CLOCK_GATE_DISABLE             (1 << 1)
# define ZVUNIT_CLOCK_GATE_DISABLE              (1 << 0) /* 830 */
# define OVLUNIT_CLOCK_GATE_DISABLE             (1 << 0) /* 845,865 */

#define RENCLK_GATE_D1          0x6204
# define BLITTER_CLOCK_GATE_DISABLE             (1 << 13) /* 945GM only */
# define MPEG_CLOCK_GATE_DISABLE                (1 << 12) /* 945GM only */
# define PC_FE_CLOCK_GATE_DISABLE               (1 << 11)
# define PC_BE_CLOCK_GATE_DISABLE               (1 << 10)
# define WINDOWER_CLOCK_GATE_DISABLE            (1 << 9)
# define INTERPOLATOR_CLOCK_GATE_DISABLE        (1 << 8)
# define COLOR_CALCULATOR_CLOCK_GATE_DISABLE    (1 << 7)
# define MOTION_COMP_CLOCK_GATE_DISABLE         (1 << 6)
# define MAG_CLOCK_GATE_DISABLE                 (1 << 5)
/** This bit must be unset on 855,865 */
# define MECI_CLOCK_GATE_DISABLE                (1 << 4)
# define DCMP_CLOCK_GATE_DISABLE                (1 << 3)
# define MEC_CLOCK_GATE_DISABLE                 (1 << 2)
# define MECO_CLOCK_GATE_DISABLE                (1 << 1)
/** This bit must be set on 855,865. */
# define SV_CLOCK_GATE_DISABLE                  (1 << 0)
# define I915_MPEG_CLOCK_GATE_DISABLE           (1 << 16)
# define I915_VLD_IP_PR_CLOCK_GATE_DISABLE      (1 << 15)
# define I915_MOTION_COMP_CLOCK_GATE_DISABLE    (1 << 14)
# define I915_BD_BF_CLOCK_GATE_DISABLE          (1 << 13)
# define I915_SF_SE_CLOCK_GATE_DISABLE          (1 << 12)
# define I915_WM_CLOCK_GATE_DISABLE             (1 << 11)
# define I915_IZ_CLOCK_GATE_DISABLE             (1 << 10)
# define I915_PI_CLOCK_GATE_DISABLE             (1 << 9)
# define I915_DI_CLOCK_GATE_DISABLE             (1 << 8)
# define I915_SH_SV_CLOCK_GATE_DISABLE          (1 << 7)
# define I915_PL_DG_QC_FT_CLOCK_GATE_DISABLE    (1 << 6)
# define I915_SC_CLOCK_GATE_DISABLE             (1 << 5)
# define I915_FL_CLOCK_GATE_DISABLE             (1 << 4)
# define I915_DM_CLOCK_GATE_DISABLE             (1 << 3)
# define I915_PS_CLOCK_GATE_DISABLE             (1 << 2)
# define I915_CC_CLOCK_GATE_DISABLE             (1 << 1)
# define I915_BY_CLOCK_GATE_DISABLE             (1 << 0)

# define I965_RCZ_CLOCK_GATE_DISABLE            (1 << 30)
/** This bit must always be set on 965G/965GM */
# define I965_RCC_CLOCK_GATE_DISABLE            (1 << 29)
# define I965_RCPB_CLOCK_GATE_DISABLE           (1 << 28)
# define I965_DAP_CLOCK_GATE_DISABLE            (1 << 27)
# define I965_ROC_CLOCK_GATE_DISABLE            (1 << 26)
# define I965_GW_CLOCK_GATE_DISABLE             (1 << 25)
# define I965_TD_CLOCK_GATE_DISABLE             (1 << 24)
/** This bit must always be set on 965G */
# define I965_ISC_CLOCK_GATE_DISABLE            (1 << 23)
# define I965_IC_CLOCK_GATE_DISABLE             (1 << 22)
# define I965_EU_CLOCK_GATE_DISABLE             (1 << 21)
# define I965_IF_CLOCK_GATE_DISABLE             (1 << 20)
# define I965_TC_CLOCK_GATE_DISABLE             (1 << 19)
# define I965_SO_CLOCK_GATE_DISABLE             (1 << 17)
# define I965_FBC_CLOCK_GATE_DISABLE            (1 << 16)
# define I965_MARI_CLOCK_GATE_DISABLE           (1 << 15)
# define I965_MASF_CLOCK_GATE_DISABLE           (1 << 14)
# define I965_MAWB_CLOCK_GATE_DISABLE           (1 << 13)
# define I965_EM_CLOCK_GATE_DISABLE             (1 << 12)
# define I965_UC_CLOCK_GATE_DISABLE             (1 << 11)
# define I965_SI_CLOCK_GATE_DISABLE             (1 << 6)
# define I965_MT_CLOCK_GATE_DISABLE             (1 << 5)
# define I965_PL_CLOCK_GATE_DISABLE             (1 << 4)
# define I965_DG_CLOCK_GATE_DISABLE             (1 << 3)
# define I965_QC_CLOCK_GATE_DISABLE             (1 << 2)
# define I965_FT_CLOCK_GATE_DISABLE             (1 << 1)
# define I965_DM_CLOCK_GATE_DISABLE             (1 << 0)

#define RENCLK_GATE_D2          0x6208
#define VF_UNIT_CLOCK_GATE_DISABLE              (1 << 9)
#define GS_UNIT_CLOCK_GATE_DISABLE              (1 << 7)
#define CL_UNIT_CLOCK_GATE_DISABLE              (1 << 6)
#define RAMCLK_GATE_D           0x6210          /* CRL only */
#define DEUC                    0x6214          /* CRL only */

/*
 * Palette regs
 */

#define PALETTE_A               0x0a000
#define PALETTE_B               0x0a800

/* MCH MMIO space */

/*
 * MCHBAR mirror.
 *
 * This mirrors the MCHBAR MMIO space whose location is determined by
 * device 0 function 0's pci config register 0x44 or 0x48 and matches it in
 * every way.  It is not accessible from the CP register read instructions.
 *
 */
#define MCHBAR_MIRROR_BASE      0x10000

/** 915-945 and GM965 MCH register controlling DRAM channel access */
#define DCC                     0x10200
#define DCC_ADDRESSING_MODE_SINGLE_CHANNEL              (0 << 0)
#define DCC_ADDRESSING_MODE_DUAL_CHANNEL_ASYMMETRIC     (1 << 0)
#define DCC_ADDRESSING_MODE_DUAL_CHANNEL_INTERLEAVED    (2 << 0)
#define DCC_ADDRESSING_MODE_MASK                        (3 << 0)
#define DCC_CHANNEL_XOR_DISABLE                         (1 << 10)
#define DCC_CHANNEL_XOR_BIT_17                          (1 << 9)

/** 965 MCH register controlling DRAM channel configuration */
#define C0DRB3                  0x10206
#define C1DRB3                  0x10606

/* Clocking configuration register */
#define CLKCFG                  0x10c00
#define CLKCFG_FSB_400                                  (5 << 0)        /* hrawclk 100 */
#define CLKCFG_FSB_533                                  (1 << 0)        /* hrawclk 133 */
#define CLKCFG_FSB_667                                  (3 << 0)        /* hrawclk 166 */
#define CLKCFG_FSB_800                                  (2 << 0)        /* hrawclk 200 */
#define CLKCFG_FSB_1067                                 (6 << 0)        /* hrawclk 266 */
#define CLKCFG_FSB_1333                                 (7 << 0)        /* hrawclk 333 */
/* Note, below two are guess */
#define CLKCFG_FSB_1600                                 (4 << 0)        /* hrawclk 400 */
#define CLKCFG_FSB_1600_ALT                             (0 << 0)        /* hrawclk 400 */
#define CLKCFG_FSB_MASK                                 (7 << 0)
#define CLKCFG_MEM_533                                  (1 << 4)
#define CLKCFG_MEM_667                                  (2 << 4)
#define CLKCFG_MEM_800                                  (3 << 4)
#define CLKCFG_MEM_MASK                                 (7 << 4)

/** GM965 GM45 render standby register */
#define MCHBAR_RENDER_STANDBY   0x111B8

#define PEG_BAND_GAP_DATA       0x14d68

/*
 * Overlay regs
 */

#define OVADD                   0x30000
#define DOVSTA                  0x30008
#define OC_BUF                  (0x3<<20)
#define OGAMC5                  0x30010
#define OGAMC4                  0x30014
#define OGAMC3                  0x30018
#define OGAMC2                  0x3001c
#define OGAMC1                  0x30020
#define OGAMC0                  0x30024

/*
 * Display engine regs
 */

/* Pipe A timing regs */
#define HTOTAL_A        0x60000
#define HBLANK_A        0x60004
#define HSYNC_A         0x60008
#define VTOTAL_A        0x6000c
#define VBLANK_A        0x60010
#define VSYNC_A         0x60014
#define PIPEASRC        0x6001c
#define BCLRPAT_A       0x60020

/* Pipe B timing regs */
#define HTOTAL_B        0x61000
#define HBLANK_B        0x61004
#define HSYNC_B         0x61008
#define VTOTAL_B        0x6100c
#define VBLANK_B        0x61010
#define VSYNC_B         0x61014
#define PIPEBSRC        0x6101c
#define BCLRPAT_B       0x61020

/* VGA port control */
#define ADPA                    0x61100
#define   ADPA_DAC_ENABLE       (1<<31)
#define   ADPA_DAC_DISABLE      0
#define   ADPA_PIPE_SELECT_MASK (1<<30)
#define   ADPA_PIPE_A_SELECT    0
#define   ADPA_PIPE_B_SELECT    (1<<30)
#define   ADPA_USE_VGA_HVPOLARITY (1<<15)
#define   ADPA_SETS_HVPOLARITY  0
#define   ADPA_VSYNC_CNTL_DISABLE (1<<11)
#define   ADPA_VSYNC_CNTL_ENABLE 0
#define   ADPA_HSYNC_CNTL_DISABLE (1<<10)
#define   ADPA_HSYNC_CNTL_ENABLE 0
#define   ADPA_VSYNC_ACTIVE_HIGH (1<<4)
#define   ADPA_VSYNC_ACTIVE_LOW 0
#define   ADPA_HSYNC_ACTIVE_HIGH (1<<3)
#define   ADPA_HSYNC_ACTIVE_LOW 0
#define   ADPA_DPMS_MASK        (~(3<<10))
#define   ADPA_DPMS_ON          (0<<10)
#define   ADPA_DPMS_SUSPEND     (1<<10)
#define   ADPA_DPMS_STANDBY     (2<<10)
#define   ADPA_DPMS_OFF         (3<<10)

/* Hotplug control (945+ only) */
#define PORT_HOTPLUG_EN         0x61110
#define   HDMIB_HOTPLUG_INT_EN                  (1 << 29)
#define   DPB_HOTPLUG_INT_EN                    (1 << 29)
#define   HDMIC_HOTPLUG_INT_EN                  (1 << 28)
#define   DPC_HOTPLUG_INT_EN                    (1 << 28)
#define   HDMID_HOTPLUG_INT_EN                  (1 << 27)
#define   DPD_HOTPLUG_INT_EN                    (1 << 27)
#define   SDVOB_HOTPLUG_INT_EN                  (1 << 26)
#define   SDVOC_HOTPLUG_INT_EN                  (1 << 25)
#define   TV_HOTPLUG_INT_EN                     (1 << 18)
#define   CRT_EOS_INT_EN                        (1 << 10)
#define   CRT_HOTPLUG_INT_EN                    (1 << 9)
#define   CRT_HOTPLUG_FORCE_DETECT              (1 << 3)
#define CRT_HOTPLUG_ACTIVATION_PERIOD_32        (0 << 8)
/* must use period 64 on GM45 according to docs */
#define CRT_HOTPLUG_ACTIVATION_PERIOD_64        (1 << 8)
#define CRT_HOTPLUG_DAC_ON_TIME_2M              (0 << 7)
#define CRT_HOTPLUG_DAC_ON_TIME_4M              (1 << 7)
#define CRT_HOTPLUG_VOLTAGE_COMPARE_40          (0 << 5)
#define CRT_HOTPLUG_VOLTAGE_COMPARE_50          (1 << 5)
#define CRT_HOTPLUG_VOLTAGE_COMPARE_60          (2 << 5)
#define CRT_HOTPLUG_VOLTAGE_COMPARE_70          (3 << 5)
#define CRT_HOTPLUG_VOLTAGE_COMPARE_MASK        (3 << 5)
#define CRT_HOTPLUG_DETECT_DELAY_1G             (0 << 4)
#define CRT_HOTPLUG_DETECT_DELAY_2G             (1 << 4)
#define CRT_HOTPLUG_DETECT_VOLTAGE_325MV        (0 << 2)
#define CRT_HOTPLUG_DETECT_VOLTAGE_475MV        (1 << 2)
#define CRT_HOTPLUG_MASK                        (0x3fc) /* Bits 9-2 */
#define CRT_FORCE_HOTPLUG_MASK                  0xfffffe1f
#define HOTPLUG_EN_MASK (HDMIB_HOTPLUG_INT_EN | \
                         HDMIC_HOTPLUG_INT_EN |   \
                         HDMID_HOTPLUG_INT_EN |   \
                         SDVOB_HOTPLUG_INT_EN |   \
                         SDVOC_HOTPLUG_INT_EN |   \
                         TV_HOTPLUG_INT_EN |      \
                         CRT_HOTPLUG_INT_EN)


#define PORT_HOTPLUG_STAT       0x61114
#define   HDMIB_HOTPLUG_INT_STATUS              (1 << 29)
#define   DPB_HOTPLUG_INT_STATUS                (1 << 29)
#define   HDMIC_HOTPLUG_INT_STATUS              (1 << 28)
#define   DPC_HOTPLUG_INT_STATUS                (1 << 28)
#define   HDMID_HOTPLUG_INT_STATUS              (1 << 27)
#define   DPD_HOTPLUG_INT_STATUS                (1 << 27)
#define   CRT_EOS_INT_STATUS                    (1 << 12)
#define   CRT_HOTPLUG_INT_STATUS                (1 << 11)
#define   TV_HOTPLUG_INT_STATUS                 (1 << 10)
#define   CRT_HOTPLUG_MONITOR_MASK              (3 << 8)
#define   CRT_HOTPLUG_MONITOR_COLOR             (3 << 8)
#define   CRT_HOTPLUG_MONITOR_MONO              (2 << 8)
#define   CRT_HOTPLUG_MONITOR_NONE              (0 << 8)
#define   SDVOC_HOTPLUG_INT_STATUS              (1 << 7)
#define   SDVOB_HOTPLUG_INT_STATUS              (1 << 6)

/* SDVO port control */
#define SDVOB                   0x61140
#define SDVOC                   0x61160
#define   SDVO_ENABLE           (1 << 31)
#define   SDVO_PIPE_B_SELECT    (1 << 30)
#define   SDVO_STALL_SELECT     (1 << 29)
#define   SDVO_INTERRUPT_ENABLE (1 << 26)
/**
 * 915G/GM SDVO pixel multiplier.
 *
 * Programmed value is multiplier - 1, up to 5x.
 *
 * \sa DPLL_MD_UDI_MULTIPLIER_MASK
 */
#define   SDVO_PORT_MULTIPLY_MASK       (7 << 23)
#define   SDVO_PORT_MULTIPLY_SHIFT              23
#define   SDVO_PHASE_SELECT_MASK        (15 << 19)
#define   SDVO_PHASE_SELECT_DEFAULT     (6 << 19)
#define   SDVO_CLOCK_OUTPUT_INVERT      (1 << 18)
#define   SDVOC_GANG_MODE               (1 << 16)
#define   SDVO_ENCODING_SDVO            (0x0 << 10)
#define   SDVO_ENCODING_HDMI            (0x2 << 10)
/** Requird for HDMI operation */
#define   SDVO_NULL_PACKETS_DURING_VSYNC (1 << 9)
#define   SDVO_BORDER_ENABLE            (1 << 7)
#define   SDVO_AUDIO_ENABLE             (1 << 6)
/** New with 965, default is to be set */
#define   SDVO_VSYNC_ACTIVE_HIGH        (1 << 4)
/** New with 965, default is to be set */
#define   SDVO_HSYNC_ACTIVE_HIGH        (1 << 3)
#define   SDVOB_PCIE_CONCURRENCY        (1 << 3)
#define   SDVO_DETECTED                 (1 << 2)
/* Bits to be preserved when writing */
#define   SDVOB_PRESERVE_MASK ((1 << 17) | (1 << 16) | (1 << 14) | (1 << 26))
#define   SDVOC_PRESERVE_MASK ((1 << 17) | (1 << 26))

/* DVO port control */
#define DVOA                    0x61120
#define DVOB                    0x61140
#define DVOC                    0x61160
#define   DVO_ENABLE                    (1 << 31)
#define   DVO_PIPE_B_SELECT             (1 << 30)
#define   DVO_PIPE_STALL_UNUSED         (0 << 28)
#define   DVO_PIPE_STALL                (1 << 28)
#define   DVO_PIPE_STALL_TV             (2 << 28)
#define   DVO_PIPE_STALL_MASK           (3 << 28)
#define   DVO_USE_VGA_SYNC              (1 << 15)
#define   DVO_DATA_ORDER_I740           (0 << 14)
#define   DVO_DATA_ORDER_FP             (1 << 14)
#define   DVO_VSYNC_DISABLE             (1 << 11)
#define   DVO_HSYNC_DISABLE             (1 << 10)
#define   DVO_VSYNC_TRISTATE            (1 << 9)
#define   DVO_HSYNC_TRISTATE            (1 << 8)
#define   DVO_BORDER_ENABLE             (1 << 7)
#define   DVO_DATA_ORDER_GBRG           (1 << 6)
#define   DVO_DATA_ORDER_RGGB           (0 << 6)
#define   DVO_DATA_ORDER_GBRG_ERRATA    (0 << 6)
#define   DVO_DATA_ORDER_RGGB_ERRATA    (1 << 6)
#define   DVO_VSYNC_ACTIVE_HIGH         (1 << 4)
#define   DVO_HSYNC_ACTIVE_HIGH         (1 << 3)
#define   DVO_BLANK_ACTIVE_HIGH         (1 << 2)
#define   DVO_OUTPUT_CSTATE_PIXELS      (1 << 1)        /* SDG only */
#define   DVO_OUTPUT_SOURCE_SIZE_PIXELS (1 << 0)        /* SDG only */
#define   DVO_PRESERVE_MASK             (0x7<<24)
#define DVOA_SRCDIM             0x61124
#define DVOB_SRCDIM             0x61144
#define DVOC_SRCDIM             0x61164
#define   DVO_SRCDIM_HORIZONTAL_SHIFT   12
#define   DVO_SRCDIM_VERTICAL_SHIFT     0

/* LVDS port control */
#define LVDS                    0x61180
/*
 * Enables the LVDS port.  This bit must be set before DPLLs are enabled, as
 * the DPLL semantics change when the LVDS is assigned to that pipe.
 */
#define   LVDS_PORT_EN                  (1 << 31)
/* Selects pipe B for LVDS data.  Must be set on pre-965. */
#define   LVDS_PIPEB_SELECT             (1 << 30)
/* Enable border for unscaled (or aspect-scaled) display */
#define   LVDS_BORDER_ENABLE            (1 << 15)
/*
 * Enables the A0-A2 data pairs and CLKA, containing 18 bits of color data per
 * pixel.
 */
#define   LVDS_A0A2_CLKA_POWER_MASK     (3 << 8)
#define   LVDS_A0A2_CLKA_POWER_DOWN     (0 << 8)
#define   LVDS_A0A2_CLKA_POWER_UP       (3 << 8)
/*
 * Controls the A3 data pair, which contains the additional LSBs for 24 bit
 * mode.  Only enabled if LVDS_A0A2_CLKA_POWER_UP also indicates it should be
 * on.
 */
#define   LVDS_A3_POWER_MASK            (3 << 6)
#define   LVDS_A3_POWER_DOWN            (0 << 6)
#define   LVDS_A3_POWER_UP              (3 << 6)
/*
 * Controls the CLKB pair.  This should only be set when LVDS_B0B3_POWER_UP
 * is set.
 */
#define   LVDS_CLKB_POWER_MASK          (3 << 4)
#define   LVDS_CLKB_POWER_DOWN          (0 << 4)
#define   LVDS_CLKB_POWER_UP            (3 << 4)
/*
 * Controls the B0-B3 data pairs.  This must be set to match the DPLL p2
 * setting for whether we are in dual-channel mode.  The B3 pair will
 * additionally only be powered up when LVDS_A3_POWER_UP is set.
 */
#define   LVDS_B0B3_POWER_MASK          (3 << 2)
#define   LVDS_B0B3_POWER_DOWN          (0 << 2)
#define   LVDS_B0B3_POWER_UP            (3 << 2)

/* Panel power sequencing */
#define PP_STATUS       0x61200
#define   PP_ON         (1 << 31)
/*
 * Indicates that all dependencies of the panel are on:
 *
 * - PLL enabled
 * - pipe enabled
 * - LVDS/DVOB/DVOC on
 */
#define   PP_READY              (1 << 30)
#define   PP_SEQUENCE_NONE      (0 << 28)
#define   PP_SEQUENCE_ON        (1 << 28)
#define   PP_SEQUENCE_OFF       (2 << 28)
#define   PP_SEQUENCE_MASK      0x30000000
#define PP_CONTROL      0x61204
#define   POWER_TARGET_ON       (1 << 0)
#define PP_ON_DELAYS    0x61208
#define PP_OFF_DELAYS   0x6120c
#define PP_DIVISOR      0x61210

/* Panel fitting */
#define PFIT_CONTROL    0x61230
#define   PFIT_ENABLE           (1 << 31)
#define   PFIT_PIPE_MASK        (3 << 29)
#define   PFIT_PIPE_SHIFT       29
#define   VERT_INTERP_DISABLE   (0 << 10)
#define   VERT_INTERP_BILINEAR  (1 << 10)
#define   VERT_INTERP_MASK      (3 << 10)
#define   VERT_AUTO_SCALE       (1 << 9)
#define   HORIZ_INTERP_DISABLE  (0 << 6)
#define   HORIZ_INTERP_BILINEAR (1 << 6)
#define   HORIZ_INTERP_MASK     (3 << 6)
#define   HORIZ_AUTO_SCALE      (1 << 5)
#define   PANEL_8TO6_DITHER_ENABLE (1 << 3)
#define   PFIT_FILTER_FUZZY     (0 << 24)
#define   PFIT_SCALING_AUTO     (0 << 26)
#define   PFIT_SCALING_PROGRAMMED (1 << 26)
#define   PFIT_SCALING_PILLAR   (2 << 26)
#define   PFIT_SCALING_LETTER   (3 << 26)
#define PFIT_PGM_RATIOS 0x61234
#define   PFIT_VERT_SCALE_MASK                  0xfff00000
#define   PFIT_HORIZ_SCALE_MASK                 0x0000fff0
/* Pre-965 */
#define         PFIT_VERT_SCALE_SHIFT           20
#define         PFIT_VERT_SCALE_MASK            0xfff00000
#define         PFIT_HORIZ_SCALE_SHIFT          4
#define         PFIT_HORIZ_SCALE_MASK           0x0000fff0
/* 965+ */
#define         PFIT_VERT_SCALE_SHIFT_965       16
#define         PFIT_VERT_SCALE_MASK_965        0x1fff0000
#define         PFIT_HORIZ_SCALE_SHIFT_965      0
#define         PFIT_HORIZ_SCALE_MASK_965       0x00001fff

#define PFIT_AUTO_RATIOS 0x61238

/* Backlight control */
#define BLC_PWM_CTL             0x61254
#define   BACKLIGHT_MODULATION_FREQ_SHIFT               (17)
#define BLC_PWM_CTL2            0x61250 /* 965+ only */
#define   BLM_COMBINATION_MODE (1 << 30)
/*
 * This is the most significant 15 bits of the number of backlight cycles in a
 * complete cycle of the modulated backlight control.
 *
 * The actual value is this field multiplied by two.
 */
#define   BACKLIGHT_MODULATION_FREQ_MASK                (0x7fff << 17)
#define   BLM_LEGACY_MODE                               (1 << 16)
/*
 * This is the number of cycles out of the backlight modulation cycle for which
 * the backlight is on.
 *
 * This field must be no greater than the number of cycles in the complete
 * backlight modulation cycle.
 */
#define   BACKLIGHT_DUTY_CYCLE_SHIFT            (0)
#define   BACKLIGHT_DUTY_CYCLE_MASK             (0xffff)

#define BLC_HIST_CTL            0x61260

/* TV port control */
#define TV_CTL                  0x68000
/** Enables the TV encoder */
# define TV_ENC_ENABLE                  (1 << 31)
/** Sources the TV encoder input from pipe B instead of A. */
# define TV_ENC_PIPEB_SELECT            (1 << 30)
/** Outputs composite video (DAC A only) */
# define TV_ENC_OUTPUT_COMPOSITE        (0 << 28)
/** Outputs SVideo video (DAC B/C) */
# define TV_ENC_OUTPUT_SVIDEO           (1 << 28)
/** Outputs Component video (DAC A/B/C) */
# define TV_ENC_OUTPUT_COMPONENT        (2 << 28)
/** Outputs Composite and SVideo (DAC A/B/C) */
# define TV_ENC_OUTPUT_SVIDEO_COMPOSITE (3 << 28)
# define TV_TRILEVEL_SYNC               (1 << 21)
/** Enables slow sync generation (945GM only) */
# define TV_SLOW_SYNC                   (1 << 20)
/** Selects 4x oversampling for 480i and 576p */
# define TV_OVERSAMPLE_4X               (0 << 18)
/** Selects 2x oversampling for 720p and 1080i */
# define TV_OVERSAMPLE_2X               (1 << 18)
/** Selects no oversampling for 1080p */
# define TV_OVERSAMPLE_NONE             (2 << 18)
/** Selects 8x oversampling */
# define TV_OVERSAMPLE_8X               (3 << 18)
/** Selects progressive mode rather than interlaced */
# define TV_PROGRESSIVE                 (1 << 17)
/** Sets the colorburst to PAL mode.  Required for non-M PAL modes. */
# define TV_PAL_BURST                   (1 << 16)
/** Field for setting delay of Y compared to C */
# define TV_YC_SKEW_MASK                (7 << 12)
/** Enables a fix for 480p/576p standard definition modes on the 915GM only */
# define TV_ENC_SDP_FIX                 (1 << 11)
/**
 * Enables a fix for the 915GM only.
 *
 * Not sure what it does.
 */
# define TV_ENC_C0_FIX                  (1 << 10)
/** Bits that must be preserved by software */
# define TV_CTL_SAVE                    ((1 << 11) | (3 << 9) | (7 << 6) | 0xf)
# define TV_FUSE_STATE_MASK             (3 << 4)
/** Read-only state that reports all features enabled */
# define TV_FUSE_STATE_ENABLED          (0 << 4)
/** Read-only state that reports that Macrovision is disabled in hardware*/
# define TV_FUSE_STATE_NO_MACROVISION   (1 << 4)
/** Read-only state that reports that TV-out is disabled in hardware. */
# define TV_FUSE_STATE_DISABLED         (2 << 4)
/** Normal operation */
# define TV_TEST_MODE_NORMAL            (0 << 0)
/** Encoder test pattern 1 - combo pattern */
# define TV_TEST_MODE_PATTERN_1         (1 << 0)
/** Encoder test pattern 2 - full screen vertical 75% color bars */
# define TV_TEST_MODE_PATTERN_2         (2 << 0)
/** Encoder test pattern 3 - full screen horizontal 75% color bars */
# define TV_TEST_MODE_PATTERN_3         (3 << 0)
/** Encoder test pattern 4 - random noise */
# define TV_TEST_MODE_PATTERN_4         (4 << 0)
/** Encoder test pattern 5 - linear color ramps */
# define TV_TEST_MODE_PATTERN_5         (5 << 0)
/**
 * This test mode forces the DACs to 50% of full output.
 *
 * This is used for load detection in combination with TVDAC_SENSE_MASK
 */
# define TV_TEST_MODE_MONITOR_DETECT    (7 << 0)
# define TV_TEST_MODE_MASK              (7 << 0)

#define TV_DAC                  0x68004
/**
 * Reports that DAC state change logic has reported change (RO).
 *
 * This gets cleared when TV_DAC_STATE_EN is cleared
*/
# define TVDAC_STATE_CHG                (1 << 31)
# define TVDAC_SENSE_MASK               (7 << 28)
/** Reports that DAC A voltage is above the detect threshold */
# define TVDAC_A_SENSE                  (1 << 30)
/** Reports that DAC B voltage is above the detect threshold */
# define TVDAC_B_SENSE                  (1 << 29)
/** Reports that DAC C voltage is above the detect threshold */
# define TVDAC_C_SENSE                  (1 << 28)
/**
 * Enables DAC state detection logic, for load-based TV detection.
 *
 * The PLL of the chosen pipe (in TV_CTL) must be running, and the encoder set
 * to off, for load detection to work.
 */
# define TVDAC_STATE_CHG_EN             (1 << 27)
/** Sets the DAC A sense value to high */
# define TVDAC_A_SENSE_CTL              (1 << 26)
/** Sets the DAC B sense value to high */
# define TVDAC_B_SENSE_CTL              (1 << 25)
/** Sets the DAC C sense value to high */
# define TVDAC_C_SENSE_CTL              (1 << 24)
/** Overrides the ENC_ENABLE and DAC voltage levels */
# define DAC_CTL_OVERRIDE               (1 << 7)
/** Sets the slew rate.  Must be preserved in software */
# define ENC_TVDAC_SLEW_FAST            (1 << 6)
# define DAC_A_1_3_V                    (0 << 4)
# define DAC_A_1_1_V                    (1 << 4)
# define DAC_A_0_7_V                    (2 << 4)
# define DAC_A_MASK                     (3 << 4)
# define DAC_B_1_3_V                    (0 << 2)
# define DAC_B_1_1_V                    (1 << 2)
# define DAC_B_0_7_V                    (2 << 2)
# define DAC_B_MASK                     (3 << 2)
# define DAC_C_1_3_V                    (0 << 0)
# define DAC_C_1_1_V                    (1 << 0)
# define DAC_C_0_7_V                    (2 << 0)
# define DAC_C_MASK                     (3 << 0)

/**
 * CSC coefficients are stored in a floating point format with 9 bits of
 * mantissa and 2 or 3 bits of exponent.  The exponent is represented as 2**-n,
 * where 2-bit exponents are unsigned n, and 3-bit exponents are signed n with
 * -1 (0x3) being the only legal negative value.
 */
#define TV_CSC_Y                0x68010
# define TV_RY_MASK                     0x07ff0000
# define TV_RY_SHIFT                    16
# define TV_GY_MASK                     0x00000fff
# define TV_GY_SHIFT                    0

#define TV_CSC_Y2               0x68014
# define TV_BY_MASK                     0x07ff0000
# define TV_BY_SHIFT                    16
/**
 * Y attenuation for component video.
 *
 * Stored in 1.9 fixed point.
 */
# define TV_AY_MASK                     0x000003ff
# define TV_AY_SHIFT                    0

#define TV_CSC_U                0x68018
# define TV_RU_MASK                     0x07ff0000
# define TV_RU_SHIFT                    16
# define TV_GU_MASK                     0x000007ff
# define TV_GU_SHIFT                    0

#define TV_CSC_U2               0x6801c
# define TV_BU_MASK                     0x07ff0000
# define TV_BU_SHIFT                    16
/**
 * U attenuation for component video.
 *
 * Stored in 1.9 fixed point.
 */
# define TV_AU_MASK                     0x000003ff
# define TV_AU_SHIFT                    0

#define TV_CSC_V                0x68020
# define TV_RV_MASK                     0x0fff0000
# define TV_RV_SHIFT                    16
# define TV_GV_MASK                     0x000007ff
# define TV_GV_SHIFT                    0

#define TV_CSC_V2               0x68024
# define TV_BV_MASK                     0x07ff0000
# define TV_BV_SHIFT                    16
/**
 * V attenuation for component video.
 *
 * Stored in 1.9 fixed point.
 */
# define TV_AV_MASK                     0x000007ff
# define TV_AV_SHIFT                    0

#define TV_CLR_KNOBS            0x68028
/** 2s-complement brightness adjustment */
# define TV_BRIGHTNESS_MASK             0xff000000
# define TV_BRIGHTNESS_SHIFT            24
/** Contrast adjustment, as a 2.6 unsigned floating point number */
# define TV_CONTRAST_MASK               0x00ff0000
# define TV_CONTRAST_SHIFT              16
/** Saturation adjustment, as a 2.6 unsigned floating point number */
# define TV_SATURATION_MASK             0x0000ff00
# define TV_SATURATION_SHIFT            8
/** Hue adjustment, as an integer phase angle in degrees */
# define TV_HUE_MASK                    0x000000ff
# define TV_HUE_SHIFT                   0

#define TV_CLR_LEVEL            0x6802c
/** Controls the DAC level for black */
# define TV_BLACK_LEVEL_MASK            0x01ff0000
# define TV_BLACK_LEVEL_SHIFT           16
/** Controls the DAC level for blanking */
# define TV_BLANK_LEVEL_MASK            0x000001ff
# define TV_BLANK_LEVEL_SHIFT           0

#define TV_H_CTL_1              0x68030
/** Number of pixels in the hsync. */
# define TV_HSYNC_END_MASK              0x1fff0000
# define TV_HSYNC_END_SHIFT             16
/** Total number of pixels minus one in the line (display and blanking). */
# define TV_HTOTAL_MASK                 0x00001fff
# define TV_HTOTAL_SHIFT                0

#define TV_H_CTL_2              0x68034
/** Enables the colorburst (needed for non-component color) */
# define TV_BURST_ENA                   (1 << 31)
/** Offset of the colorburst from the start of hsync, in pixels minus one. */
# define TV_HBURST_START_SHIFT          16
# define TV_HBURST_START_MASK           0x1fff0000
/** Length of the colorburst */
# define TV_HBURST_LEN_SHIFT            0
# define TV_HBURST_LEN_MASK             0x0001fff

#define TV_H_CTL_3              0x68038
/** End of hblank, measured in pixels minus one from start of hsync */
# define TV_HBLANK_END_SHIFT            16
# define TV_HBLANK_END_MASK             0x1fff0000
/** Start of hblank, measured in pixels minus one from start of hsync */
# define TV_HBLANK_START_SHIFT          0
# define TV_HBLANK_START_MASK           0x0001fff

#define TV_V_CTL_1              0x6803c
/** XXX */
# define TV_NBR_END_SHIFT               16
# define TV_NBR_END_MASK                0x07ff0000
/** XXX */
# define TV_VI_END_F1_SHIFT             8
# define TV_VI_END_F1_MASK              0x00003f00
/** XXX */
# define TV_VI_END_F2_SHIFT             0
# define TV_VI_END_F2_MASK              0x0000003f

#define TV_V_CTL_2              0x68040
/** Length of vsync, in half lines */
# define TV_VSYNC_LEN_MASK              0x07ff0000
# define TV_VSYNC_LEN_SHIFT             16
/** Offset of the start of vsync in field 1, measured in one less than the
 * number of half lines.
 */
# define TV_VSYNC_START_F1_MASK         0x00007f00
# define TV_VSYNC_START_F1_SHIFT        8
/**
 * Offset of the start of vsync in field 2, measured in one less than the
 * number of half lines.
 */
# define TV_VSYNC_START_F2_MASK         0x0000007f
# define TV_VSYNC_START_F2_SHIFT        0

#define TV_V_CTL_3              0x68044
/** Enables generation of the equalization signal */
# define TV_EQUAL_ENA                   (1 << 31)
/** Length of vsync, in half lines */
# define TV_VEQ_LEN_MASK                0x007f0000
# define TV_VEQ_LEN_SHIFT               16
/** Offset of the start of equalization in field 1, measured in one less than
 * the number of half lines.
 */
# define TV_VEQ_START_F1_MASK           0x0007f00
# define TV_VEQ_START_F1_SHIFT          8
/**
 * Offset of the start of equalization in field 2, measured in one less than
 * the number of half lines.
 */
# define TV_VEQ_START_F2_MASK           0x000007f
# define TV_VEQ_START_F2_SHIFT          0

#define TV_V_CTL_4              0x68048
/**
 * Offset to start of vertical colorburst, measured in one less than the
 * number of lines from vertical start.
 */
# define TV_VBURST_START_F1_MASK        0x003f0000
# define TV_VBURST_START_F1_SHIFT       16
/**
 * Offset to the end of vertical colorburst, measured in one less than the
 * number of lines from the start of NBR.
 */
# define TV_VBURST_END_F1_MASK          0x000000ff
# define TV_VBURST_END_F1_SHIFT         0

#define TV_V_CTL_5              0x6804c
/**
 * Offset to start of vertical colorburst, measured in one less than the
 * number of lines from vertical start.
 */
# define TV_VBURST_START_F2_MASK        0x003f0000
# define TV_VBURST_START_F2_SHIFT       16
/**
 * Offset to the end of vertical colorburst, measured in one less than the
 * number of lines from the start of NBR.
 */
# define TV_VBURST_END_F2_MASK          0x000000ff
# define TV_VBURST_END_F2_SHIFT         0

#define TV_V_CTL_6              0x68050
/**
 * Offset to start of vertical colorburst, measured in one less than the
 * number of lines from vertical start.
 */
# define TV_VBURST_START_F3_MASK        0x003f0000
# define TV_VBURST_START_F3_SHIFT       16
/**
 * Offset to the end of vertical colorburst, measured in one less than the
 * number of lines from the start of NBR.
 */
# define TV_VBURST_END_F3_MASK          0x000000ff
# define TV_VBURST_END_F3_SHIFT         0

#define TV_V_CTL_7              0x68054
/**
 * Offset to start of vertical colorburst, measured in one less than the
 * number of lines from vertical start.
 */
# define TV_VBURST_START_F4_MASK        0x003f0000
# define TV_VBURST_START_F4_SHIFT       16
/**
 * Offset to the end of vertical colorburst, measured in one less than the
 * number of lines from the start of NBR.
 */
# define TV_VBURST_END_F4_MASK          0x000000ff
# define TV_VBURST_END_F4_SHIFT         0

#define TV_SC_CTL_1             0x68060
/** Turns on the first subcarrier phase generation DDA */
# define TV_SC_DDA1_EN                  (1 << 31)
/** Turns on the first subcarrier phase generation DDA */
# define TV_SC_DDA2_EN                  (1 << 30)
/** Turns on the first subcarrier phase generation DDA */
# define TV_SC_DDA3_EN                  (1 << 29)
/** Sets the subcarrier DDA to reset frequency every other field */
# define TV_SC_RESET_EVERY_2            (0 << 24)
/** Sets the subcarrier DDA to reset frequency every fourth field */
# define TV_SC_RESET_EVERY_4            (1 << 24)
/** Sets the subcarrier DDA to reset frequency every eighth field */
# define TV_SC_RESET_EVERY_8            (2 << 24)
/** Sets the subcarrier DDA to never reset the frequency */
# define TV_SC_RESET_NEVER              (3 << 24)
/** Sets the peak amplitude of the colorburst.*/
# define TV_BURST_LEVEL_MASK            0x00ff0000
# define TV_BURST_LEVEL_SHIFT           16
/** Sets the increment of the first subcarrier phase generation DDA */
# define TV_SCDDA1_INC_MASK             0x00000fff
# define TV_SCDDA1_INC_SHIFT            0

#define TV_SC_CTL_2             0x68064
/** Sets the rollover for the second subcarrier phase generation DDA */
# define TV_SCDDA2_SIZE_MASK            0x7fff0000
# define TV_SCDDA2_SIZE_SHIFT           16
/** Sets the increent of the second subcarrier phase generation DDA */
# define TV_SCDDA2_INC_MASK             0x00007fff
# define TV_SCDDA2_INC_SHIFT            0

#define TV_SC_CTL_3             0x68068
/** Sets the rollover for the third subcarrier phase generation DDA */
# define TV_SCDDA3_SIZE_MASK            0x7fff0000
# define TV_SCDDA3_SIZE_SHIFT           16
/** Sets the increent of the third subcarrier phase generation DDA */
# define TV_SCDDA3_INC_MASK             0x00007fff
# define TV_SCDDA3_INC_SHIFT            0

#define TV_WIN_POS              0x68070
/** X coordinate of the display from the start of horizontal active */
# define TV_XPOS_MASK                   0x1fff0000
# define TV_XPOS_SHIFT                  16
/** Y coordinate of the display from the start of vertical active (NBR) */
# define TV_YPOS_MASK                   0x00000fff
# define TV_YPOS_SHIFT                  0

#define TV_WIN_SIZE             0x68074
/** Horizontal size of the display window, measured in pixels*/
# define TV_XSIZE_MASK                  0x1fff0000
# define TV_XSIZE_SHIFT                 16
/**
 * Vertical size of the display window, measured in pixels.
 *
 * Must be even for interlaced modes.
 */
# define TV_YSIZE_MASK                  0x00000fff
# define TV_YSIZE_SHIFT                 0

#define TV_FILTER_CTL_1         0x68080
/**
 * Enables automatic scaling calculation.
 *
 * If set, the rest of the registers are ignored, and the calculated values can
 * be read back from the register.
 */
# define TV_AUTO_SCALE                  (1 << 31)
/**
 * Disables the vertical filter.
 *
 * This is required on modes more than 1024 pixels wide */
# define TV_V_FILTER_BYPASS             (1 << 29)
/** Enables adaptive vertical filtering */
# define TV_VADAPT                      (1 << 28)
# define TV_VADAPT_MODE_MASK            (3 << 26)
/** Selects the least adaptive vertical filtering mode */
# define TV_VADAPT_MODE_LEAST           (0 << 26)
/** Selects the moderately adaptive vertical filtering mode */
# define TV_VADAPT_MODE_MODERATE        (1 << 26)
/** Selects the most adaptive vertical filtering mode */
# define TV_VADAPT_MODE_MOST            (3 << 26)
/**
 * Sets the horizontal scaling factor.
 *
 * This should be the fractional part of the horizontal scaling factor divided
 * by the oversampling rate.  TV_HSCALE should be less than 1, and set to:
 *
 * (src width - 1) / ((oversample * dest width) - 1)
 */
# define TV_HSCALE_FRAC_MASK            0x00003fff
# define TV_HSCALE_FRAC_SHIFT           0

#define TV_FILTER_CTL_2         0x68084
/**
 * Sets the integer part of the 3.15 fixed-point vertical scaling factor.
 *
 * TV_VSCALE should be (src height - 1) / ((interlace * dest height) - 1)
 */
# define TV_VSCALE_INT_MASK             0x00038000
# define TV_VSCALE_INT_SHIFT            15
/**
 * Sets the fractional part of the 3.15 fixed-point vertical scaling factor.
 *
 * \sa TV_VSCALE_INT_MASK
 */
# define TV_VSCALE_FRAC_MASK            0x00007fff
# define TV_VSCALE_FRAC_SHIFT           0

#define TV_FILTER_CTL_3         0x68088
/**
 * Sets the integer part of the 3.15 fixed-point vertical scaling factor.
 *
 * TV_VSCALE should be (src height - 1) / (1/4 * (dest height - 1))
 *
 * For progressive modes, TV_VSCALE_IP_INT should be set to zeroes.
 */
# define TV_VSCALE_IP_INT_MASK          0x00038000
# define TV_VSCALE_IP_INT_SHIFT         15
/**
 * Sets the fractional part of the 3.15 fixed-point vertical scaling factor.
 *
 * For progressive modes, TV_VSCALE_IP_INT should be set to zeroes.
 *
 * \sa TV_VSCALE_IP_INT_MASK
 */
# define TV_VSCALE_IP_FRAC_MASK         0x00007fff
# define TV_VSCALE_IP_FRAC_SHIFT                0

#define TV_CC_CONTROL           0x68090
# define TV_CC_ENABLE                   (1 << 31)
/**
 * Specifies which field to send the CC data in.
 *
 * CC data is usually sent in field 0.
 */
# define TV_CC_FID_MASK                 (1 << 27)
# define TV_CC_FID_SHIFT                27
/** Sets the horizontal position of the CC data.  Usually 135. */
# define TV_CC_HOFF_MASK                0x03ff0000
# define TV_CC_HOFF_SHIFT               16
/** Sets the vertical position of the CC data.  Usually 21 */
# define TV_CC_LINE_MASK                0x0000003f
# define TV_CC_LINE_SHIFT               0

#define TV_CC_DATA              0x68094
# define TV_CC_RDY                      (1 << 31)
/** Second word of CC data to be transmitted. */
# define TV_CC_DATA_2_MASK              0x007f0000
# define TV_CC_DATA_2_SHIFT             16
/** First word of CC data to be transmitted. */
# define TV_CC_DATA_1_MASK              0x0000007f
# define TV_CC_DATA_1_SHIFT             0

#define TV_H_LUMA_0             0x68100
#define TV_H_LUMA_59            0x681ec
#define TV_H_CHROMA_0           0x68200
#define TV_H_CHROMA_59          0x682ec
#define TV_V_LUMA_0             0x68300
#define TV_V_LUMA_42            0x683a8
#define TV_V_CHROMA_0           0x68400
#define TV_V_CHROMA_42          0x684a8

/* Display Port */
#define DP_A                            0x64000 /* eDP */
#define DP_B                            0x64100
#define DP_C                            0x64200
#define DP_D                            0x64300

#define   DP_PORT_EN                    (1 << 31)
#define   DP_PIPEB_SELECT               (1 << 30)

/* Link training mode - select a suitable mode for each stage */
#define   DP_LINK_TRAIN_PAT_1           (0 << 28)
#define   DP_LINK_TRAIN_PAT_2           (1 << 28)
#define   DP_LINK_TRAIN_PAT_IDLE        (2 << 28)
#define   DP_LINK_TRAIN_OFF             (3 << 28)
#define   DP_LINK_TRAIN_MASK            (3 << 28)
#define   DP_LINK_TRAIN_SHIFT           28

/* Signal voltages. These are mostly controlled by the other end */
#define   DP_VOLTAGE_0_4                (0 << 25)
#define   DP_VOLTAGE_0_6                (1 << 25)
#define   DP_VOLTAGE_0_8                (2 << 25)
#define   DP_VOLTAGE_1_2                (3 << 25)
#define   DP_VOLTAGE_MASK               (7 << 25)
#define   DP_VOLTAGE_SHIFT              25

/* Signal pre-emphasis levels, like voltages, the other end tells us what
 * they want
 */
#define   DP_PRE_EMPHASIS_0             (0 << 22)
#define   DP_PRE_EMPHASIS_3_5           (1 << 22)
#define   DP_PRE_EMPHASIS_6             (2 << 22)
#define   DP_PRE_EMPHASIS_9_5           (3 << 22)
#define   DP_PRE_EMPHASIS_MASK          (7 << 22)
#define   DP_PRE_EMPHASIS_SHIFT         22

/* How many wires to use. I guess 3 was too hard */
#define   DP_PORT_WIDTH_1               (0 << 19)
#define   DP_PORT_WIDTH_2               (1 << 19)
#define   DP_PORT_WIDTH_4               (3 << 19)
#define   DP_PORT_WIDTH_MASK            (7 << 19)

/* Mystic DPCD version 1.1 special mode */
#define   DP_ENHANCED_FRAMING           (1 << 18)

/* eDP */
#define   DP_PLL_FREQ_270MHZ            (0 << 16)
#define   DP_PLL_FREQ_160MHZ            (1 << 16)
#define   DP_PLL_FREQ_MASK              (3 << 16)

/** locked once port is enabled */
#define   DP_PORT_REVERSAL              (1 << 15)

/* eDP */
#define   DP_PLL_ENABLE                 (1 << 14)

/** sends the clock on lane 15 of the PEG for debug */
#define   DP_CLOCK_OUTPUT_ENABLE        (1 << 13)

#define   DP_SCRAMBLING_DISABLE         (1 << 12)
#define   DP_SCRAMBLING_DISABLE_IGDNG   (1 << 7)

/** limit RGB values to avoid confusing TVs */
#define   DP_COLOR_RANGE_16_235         (1 << 8)

/** Turn on the audio link */
#define   DP_AUDIO_OUTPUT_ENABLE        (1 << 6)

/** vs and hs sync polarity */
#define   DP_SYNC_VS_HIGH               (1 << 4)
#define   DP_SYNC_HS_HIGH               (1 << 3)

/** A fantasy */
#define   DP_DETECTED                   (1 << 2)

/** The aux channel provides a way to talk to the
 * signal sink for DDC etc. Max packet size supported
 * is 20 bytes in each direction, hence the 5 fixed
 * data registers
 */
#define DPA_AUX_CH_CTL                  0x64010
#define DPA_AUX_CH_DATA1                0x64014
#define DPA_AUX_CH_DATA2                0x64018
#define DPA_AUX_CH_DATA3                0x6401c
#define DPA_AUX_CH_DATA4                0x64020
#define DPA_AUX_CH_DATA5                0x64024

#define DPB_AUX_CH_CTL                  0x64110
#define DPB_AUX_CH_DATA1                0x64114
#define DPB_AUX_CH_DATA2                0x64118
#define DPB_AUX_CH_DATA3                0x6411c
#define DPB_AUX_CH_DATA4                0x64120
#define DPB_AUX_CH_DATA5                0x64124

#define DPC_AUX_CH_CTL                  0x64210
#define DPC_AUX_CH_DATA1                0x64214
#define DPC_AUX_CH_DATA2                0x64218
#define DPC_AUX_CH_DATA3                0x6421c
#define DPC_AUX_CH_DATA4                0x64220
#define DPC_AUX_CH_DATA5                0x64224

#define DPD_AUX_CH_CTL                  0x64310
#define DPD_AUX_CH_DATA1                0x64314
#define DPD_AUX_CH_DATA2                0x64318
#define DPD_AUX_CH_DATA3                0x6431c
#define DPD_AUX_CH_DATA4                0x64320
#define DPD_AUX_CH_DATA5                0x64324

#define   DP_AUX_CH_CTL_SEND_BUSY           (1 << 31)
#define   DP_AUX_CH_CTL_DONE                (1 << 30)
#define   DP_AUX_CH_CTL_INTERRUPT           (1 << 29)
#define   DP_AUX_CH_CTL_TIME_OUT_ERROR      (1 << 28)
#define   DP_AUX_CH_CTL_TIME_OUT_400us      (0 << 26)
#define   DP_AUX_CH_CTL_TIME_OUT_600us      (1 << 26)
#define   DP_AUX_CH_CTL_TIME_OUT_800us      (2 << 26)
#define   DP_AUX_CH_CTL_TIME_OUT_1600us     (3 << 26)
#define   DP_AUX_CH_CTL_TIME_OUT_MASK       (3 << 26)
#define   DP_AUX_CH_CTL_RECEIVE_ERROR       (1 << 25)
#define   DP_AUX_CH_CTL_MESSAGE_SIZE_MASK    (0x1f << 20)
#define   DP_AUX_CH_CTL_MESSAGE_SIZE_SHIFT   20
#define   DP_AUX_CH_CTL_PRECHARGE_2US_MASK   (0xf << 16)
#define   DP_AUX_CH_CTL_PRECHARGE_2US_SHIFT  16
#define   DP_AUX_CH_CTL_AUX_AKSV_SELECT     (1 << 15)
#define   DP_AUX_CH_CTL_MANCHESTER_TEST     (1 << 14)
#define   DP_AUX_CH_CTL_SYNC_TEST           (1 << 13)
#define   DP_AUX_CH_CTL_DEGLITCH_TEST       (1 << 12)
#define   DP_AUX_CH_CTL_PRECHARGE_TEST      (1 << 11)
#define   DP_AUX_CH_CTL_BIT_CLOCK_2X_MASK    (0x7ff)
#define   DP_AUX_CH_CTL_BIT_CLOCK_2X_SHIFT   0

/*
 * Computing GMCH M and N values for the Display Port link
 *
 * GMCH M/N = dot clock * bytes per pixel / ls_clk * # of lanes
 *
 * ls_clk (we assume) is the DP link clock (1.62 or 2.7 GHz)
 *
 * The GMCH value is used internally
 *
 * bytes_per_pixel is the number of bytes coming out of the plane,
 * which is after the LUTs, so we want the bytes for our color format.
 * For our current usage, this is always 3, one byte for R, G and B.
 */
#define PIPEA_GMCH_DATA_M                       0x70050
#define PIPEB_GMCH_DATA_M                       0x71050

/* Transfer unit size for display port - 1, default is 0x3f (for TU size 64) */
#define   PIPE_GMCH_DATA_M_TU_SIZE_MASK         (0x3f << 25)
#define   PIPE_GMCH_DATA_M_TU_SIZE_SHIFT        25

#define   PIPE_GMCH_DATA_M_MASK                 (0xffffff)

#define PIPEA_GMCH_DATA_N                       0x70054
#define PIPEB_GMCH_DATA_N                       0x71054
#define   PIPE_GMCH_DATA_N_MASK                 (0xffffff)

/*
 * Computing Link M and N values for the Display Port link
 *
 * Link M / N = pixel_clock / ls_clk
 *
 * (the DP spec calls pixel_clock the 'strm_clk')
 *
 * The Link value is transmitted in the Main Stream
 * Attributes and VB-ID.
 */

#define PIPEA_DP_LINK_M                         0x70060
#define PIPEB_DP_LINK_M                         0x71060
#define   PIPEA_DP_LINK_M_MASK                  (0xffffff)

#define PIPEA_DP_LINK_N                         0x70064
#define PIPEB_DP_LINK_N                         0x71064
#define   PIPEA_DP_LINK_N_MASK                  (0xffffff)

/* Display & cursor control */

/* Pipe A */
#define PIPEADSL                0x70000
#define PIPEACONF               0x70008
#define   PIPEACONF_ENABLE      (1<<31)
#define   PIPEACONF_DISABLE     0
#define   PIPEACONF_DOUBLE_WIDE (1<<30)
#define   I965_PIPECONF_ACTIVE  (1<<30)
#define   PIPEACONF_SINGLE_WIDE 0
#define   PIPEACONF_PIPE_UNLOCKED 0
#define   PIPEACONF_PIPE_LOCKED (1<<25)
#define   PIPEACONF_PALETTE     0
#define   PIPEACONF_GAMMA               (1<<24)
#define   PIPECONF_FORCE_BORDER (1<<25)
#define   PIPECONF_PROGRESSIVE  (0 << 21)
#define   PIPECONF_INTERLACE_W_FIELD_INDICATION (6 << 21)
#define   PIPECONF_INTERLACE_FIELD_0_ONLY               (7 << 21)
#define   PIPECONF_CXSR_DOWNCLOCK       (1<<16)
#define PIPEASTAT               0x70024
#define   PIPE_FIFO_UNDERRUN_STATUS             (1UL<<31)
#define   PIPE_CRC_ERROR_ENABLE                 (1UL<<29)
#define   PIPE_CRC_DONE_ENABLE                  (1UL<<28)
#define   PIPE_GMBUS_EVENT_ENABLE               (1UL<<27)
#define   PIPE_HOTPLUG_INTERRUPT_ENABLE         (1UL<<26)
#define   PIPE_VSYNC_INTERRUPT_ENABLE           (1UL<<25)
#define   PIPE_DISPLAY_LINE_COMPARE_ENABLE      (1UL<<24)
#define   PIPE_DPST_EVENT_ENABLE                (1UL<<23)
#define   PIPE_LEGACY_BLC_EVENT_ENABLE          (1UL<<22)
#define   PIPE_ODD_FIELD_INTERRUPT_ENABLE       (1UL<<21)
#define   PIPE_EVEN_FIELD_INTERRUPT_ENABLE      (1UL<<20)
#define   PIPE_HOTPLUG_TV_INTERRUPT_ENABLE      (1UL<<18) /* pre-965 */
#define   PIPE_START_VBLANK_INTERRUPT_ENABLE    (1UL<<18) /* 965 or later */
#define   PIPE_VBLANK_INTERRUPT_ENABLE          (1UL<<17)
#define   PIPE_OVERLAY_UPDATED_ENABLE           (1UL<<16)
#define   PIPE_CRC_ERROR_INTERRUPT_STATUS       (1UL<<13)
#define   PIPE_CRC_DONE_INTERRUPT_STATUS        (1UL<<12)
#define   PIPE_GMBUS_INTERRUPT_STATUS           (1UL<<11)
#define   PIPE_HOTPLUG_INTERRUPT_STATUS         (1UL<<10)
#define   PIPE_VSYNC_INTERRUPT_STATUS           (1UL<<9)
#define   PIPE_DISPLAY_LINE_COMPARE_STATUS      (1UL<<8)
#define   PIPE_DPST_EVENT_STATUS                (1UL<<7)
#define   PIPE_LEGACY_BLC_EVENT_STATUS          (1UL<<6)
#define   PIPE_ODD_FIELD_INTERRUPT_STATUS       (1UL<<5)
#define   PIPE_EVEN_FIELD_INTERRUPT_STATUS      (1UL<<4)
#define   PIPE_HOTPLUG_TV_INTERRUPT_STATUS      (1UL<<2) /* pre-965 */
#define   PIPE_START_VBLANK_INTERRUPT_STATUS    (1UL<<2) /* 965 or later */
#define   PIPE_VBLANK_INTERRUPT_STATUS          (1UL<<1)
#define   PIPE_OVERLAY_UPDATED_STATUS           (1UL<<0)
#define   PIPE_BPC_MASK                         (7 << 5) /* Ironlake */
#define   PIPE_8BPC                             (0 << 5)
#define   PIPE_10BPC                            (1 << 5)
#define   PIPE_6BPC                             (2 << 5)
#define   PIPE_12BPC                            (3 << 5)

#define DSPARB                  0x70030
#define   DSPARB_CSTART_MASK    (0x7f << 7)
#define   DSPARB_CSTART_SHIFT   7
#define   DSPARB_BSTART_MASK    (0x7f)
#define   DSPARB_BSTART_SHIFT   0
#define   DSPARB_BEND_SHIFT     9 /* on 855 */
#define   DSPARB_AEND_SHIFT     0

#define DSPFW1                  0x70034
#define   DSPFW_SR_SHIFT        23
#define   DSPFW_CURSORB_SHIFT   16
#define   DSPFW_PLANEB_SHIFT    8
#define DSPFW2                  0x70038
#define   DSPFW_CURSORA_MASK    0x00003f00
#define   DSPFW_CURSORA_SHIFT   16
#define DSPFW3                  0x7003c
#define   DSPFW_HPLL_SR_EN      (1<<31)
#define   DSPFW_CURSOR_SR_SHIFT 24
#define   IGD_SELF_REFRESH_EN   (1<<30)

/* FIFO watermark sizes etc */
#define G4X_FIFO_LINE_SIZE      64
#define I915_FIFO_LINE_SIZE     64
#define I830_FIFO_LINE_SIZE     32

#define G4X_FIFO_SIZE           127
#define I945_FIFO_SIZE          127 /* 945 & 965 */
#define I915_FIFO_SIZE          95
#define I855GM_FIFO_SIZE        127 /* In cachelines */
#define I830_FIFO_SIZE          95

#define G4X_MAX_WM              0x3f
#define I915_MAX_WM             0x3f

#define IGD_DISPLAY_FIFO        512 /* in 64byte unit */
#define IGD_FIFO_LINE_SIZE      64
#define IGD_MAX_WM              0x1ff
#define IGD_DFT_WM              0x3f
#define IGD_DFT_HPLLOFF_WM      0
#define IGD_GUARD_WM            10
#define IGD_CURSOR_FIFO         64
#define IGD_CURSOR_MAX_WM       0x3f
#define IGD_CURSOR_DFT_WM       0
#define IGD_CURSOR_GUARD_WM     5

/*
 * The two pipe frame counter registers are not synchronized, so
 * reading a stable value is somewhat tricky. The following code
 * should work:
 *
 *  do {
 *    high1 = ((INREG(PIPEAFRAMEHIGH) & PIPE_FRAME_HIGH_MASK) >>
 *             PIPE_FRAME_HIGH_SHIFT;
 *    low1 =  ((INREG(PIPEAFRAMEPIXEL) & PIPE_FRAME_LOW_MASK) >>
 *             PIPE_FRAME_LOW_SHIFT);
 *    high2 = ((INREG(PIPEAFRAMEHIGH) & PIPE_FRAME_HIGH_MASK) >>
 *             PIPE_FRAME_HIGH_SHIFT);
 *  } while (high1 != high2);
 *  frame = (high1 << 8) | low1;
 */
#define PIPEAFRAMEHIGH          0x70040
#define   PIPE_FRAME_HIGH_MASK    0x0000ffff
#define   PIPE_FRAME_HIGH_SHIFT   0
#define PIPEAFRAMEPIXEL         0x70044
#define   PIPE_FRAME_LOW_MASK     0xff000000
#define   PIPE_FRAME_LOW_SHIFT    24
#define   PIPE_PIXEL_MASK         0x00ffffff
#define   PIPE_PIXEL_SHIFT        0
/* GM45+ just has to be different */
#define PIPEA_FRMCOUNT_GM45     0x70040
#define PIPEA_FLIPCOUNT_GM45    0x70044

/* Cursor A & B regs */
#define CURACNTR                0x70080
/* Old style CUR*CNTR flags (desktop 8xx) */
#define   CURSOR_ENABLE         0x80000000
#define   CURSOR_GAMMA_ENABLE   0x40000000
#define   CURSOR_STRIDE_MASK    0x30000000
#define   CURSOR_FORMAT_SHIFT   24
#define   CURSOR_FORMAT_MASK    (0x07 << CURSOR_FORMAT_SHIFT)
#define   CURSOR_FORMAT_2C      (0x00 << CURSOR_FORMAT_SHIFT)
#define   CURSOR_FORMAT_3C      (0x01 << CURSOR_FORMAT_SHIFT)
#define   CURSOR_FORMAT_4C      (0x02 << CURSOR_FORMAT_SHIFT)
#define   CURSOR_FORMAT_ARGB    (0x04 << CURSOR_FORMAT_SHIFT)
#define   CURSOR_FORMAT_XRGB    (0x05 << CURSOR_FORMAT_SHIFT)
/* New style CUR*CNTR flags */
#define   CURSOR_MODE           0x27
#define   CURSOR_MODE_DISABLE   0x00
#define   CURSOR_MODE_64_32B_AX 0x07
#define   CURSOR_MODE_64_ARGB_AX ((1 << 5) | CURSOR_MODE_64_32B_AX)
#define   MCURSOR_PIPE_SELECT   (1 << 28)
#define   MCURSOR_PIPE_A        0x00
#define   MCURSOR_PIPE_B        (1 << 28)
#define   MCURSOR_GAMMA_ENABLE  (1 << 26)
#define CURABASE                0x70084
#define CURAPOS                 0x70088
#define   CURSOR_POS_MASK       0x007FF
#define   CURSOR_POS_SIGN       0x8000
#define   CURSOR_X_SHIFT        0
#define   CURSOR_Y_SHIFT        16
#define CURSIZE                 0x700a0
#define CURBCNTR                0x700c0
#define CURBBASE                0x700c4
#define CURBPOS                 0x700c8

/* Display A control */
#define DSPACNTR                0x70180
#define   DISPLAY_PLANE_ENABLE                  (1<<31)
#define   DISPLAY_PLANE_DISABLE                 0
#define   DISPPLANE_GAMMA_ENABLE                (1<<30)
#define   DISPPLANE_GAMMA_DISABLE               0
#define   DISPPLANE_PIXFORMAT_MASK              (0xf<<26)
#define   DISPPLANE_8BPP                        (0x2<<26)
#define   DISPPLANE_15_16BPP                    (0x4<<26)
#define   DISPPLANE_16BPP                       (0x5<<26)
#define   DISPPLANE_32BPP_NO_ALPHA              (0x6<<26)
#define   DISPPLANE_32BPP                       (0x7<<26)
#define   DISPPLANE_STEREO_ENABLE               (1<<25)
#define   DISPPLANE_STEREO_DISABLE              0
#define   DISPPLANE_SEL_PIPE_MASK               (1<<24)
#define   DISPPLANE_SEL_PIPE_A                  0
#define   DISPPLANE_SEL_PIPE_B                  (1<<24)
#define   DISPPLANE_SRC_KEY_ENABLE              (1<<22)
#define   DISPPLANE_SRC_KEY_DISABLE             0
#define   DISPPLANE_LINE_DOUBLE                 (1<<20)
#define   DISPPLANE_NO_LINE_DOUBLE              0
#define   DISPPLANE_STEREO_POLARITY_FIRST       0
#define   DISPPLANE_STEREO_POLARITY_SECOND      (1<<18)
#define   DISPPLANE_TRICKLE_FEED_DISABLE        (1<<14) /* IGDNG */
#define   DISPPLANE_TILED                       (1<<10)
#define DSPAADDR                0x70184
#define DSPASTRIDE              0x70188
#define DSPAPOS                 0x7018C /* reserved */
#define DSPASIZE                0x70190
#define DSPASURF                0x7019C /* 965+ only */
#define DSPATILEOFF             0x701A4 /* 965+ only */

/* VBIOS flags */
#define SWF00                   0x71410
#define SWF01                   0x71414
#define SWF02                   0x71418
#define SWF03                   0x7141c
#define SWF04                   0x71420
#define SWF05                   0x71424
#define SWF06                   0x71428
#define SWF10                   0x70410
#define SWF11                   0x70414
#define SWF14                   0x71420
#define SWF30                   0x72414
#define SWF31                   0x72418
#define SWF32                   0x7241c

/* Pipe B */
#define PIPEBDSL                0x71000
#define PIPEBCONF               0x71008
#define PIPEBSTAT               0x71024
#define PIPEBFRAMEHIGH          0x71040
#define PIPEBFRAMEPIXEL         0x71044
#define PIPEB_FRMCOUNT_GM45     0x71040
#define PIPEB_FLIPCOUNT_GM45    0x71044


/* Display B control */
#define DSPBCNTR                0x71180
#define   DISPPLANE_ALPHA_TRANS_ENABLE          (1<<15)
#define   DISPPLANE_ALPHA_TRANS_DISABLE         0
#define   DISPPLANE_SPRITE_ABOVE_DISPLAY        0
#define   DISPPLANE_SPRITE_ABOVE_OVERLAY        (1)
#define DSPBADDR                0x71184
#define DSPBSTRIDE              0x71188
#define DSPBPOS                 0x7118C
#define DSPBSIZE                0x71190
#define DSPBSURF                0x7119C
#define DSPBTILEOFF             0x711A4

/* VBIOS regs */
#define VGACNTRL                0x71400
# define VGA_DISP_DISABLE                       (1 << 31)
# define VGA_2X_MODE                            (1 << 30)
# define VGA_PIPE_B_SELECT                      (1 << 29)

/* IGDNG */

#define CPU_VGACNTRL    0x41000

#define DIGITAL_PORT_HOTPLUG_CNTRL      0x44030
#define  DIGITAL_PORTA_HOTPLUG_ENABLE           (1 << 4)
#define  DIGITAL_PORTA_SHORT_PULSE_2MS          (0 << 2)
#define  DIGITAL_PORTA_SHORT_PULSE_4_5MS        (1 << 2)
#define  DIGITAL_PORTA_SHORT_PULSE_6MS          (2 << 2)
#define  DIGITAL_PORTA_SHORT_PULSE_100MS        (3 << 2)
#define  DIGITAL_PORTA_NO_DETECT                (0 << 0)
#define  DIGITAL_PORTA_LONG_PULSE_DETECT_MASK   (1 << 1)
#define  DIGITAL_PORTA_SHORT_PULSE_DETECT_MASK  (1 << 0)

/* refresh rate hardware control */
#define RR_HW_CTL       0x45300
#define  RR_HW_LOW_POWER_FRAMES_MASK    0xff
#define  RR_HW_HIGH_POWER_FRAMES_MASK   0xff00

#define FDI_PLL_BIOS_0  0x46000
#define FDI_PLL_BIOS_1  0x46004
#define FDI_PLL_BIOS_2  0x46008
#define DISPLAY_PORT_PLL_BIOS_0         0x4600c
#define DISPLAY_PORT_PLL_BIOS_1         0x46010
#define DISPLAY_PORT_PLL_BIOS_2         0x46014

#define FDI_PLL_FREQ_CTL        0x46030
#define  FDI_PLL_FREQ_CHANGE_REQUEST    (1<<24)
#define  FDI_PLL_FREQ_LOCK_LIMIT_MASK   0xfff00
#define  FDI_PLL_FREQ_DISABLE_COUNT_LIMIT_MASK  0xff


#define PIPEA_DATA_M1           0x60030
#define  TU_SIZE(x)             (((x)-1) << 25) /* default size 64 */
#define  TU_SIZE_MASK           0x7e000000
#define  PIPEA_DATA_M1_OFFSET   0
#define PIPEA_DATA_N1           0x60034
#define  PIPEA_DATA_N1_OFFSET   0

#define PIPEA_DATA_M2           0x60038
#define  PIPEA_DATA_M2_OFFSET   0
#define PIPEA_DATA_N2           0x6003c
#define  PIPEA_DATA_N2_OFFSET   0

#define PIPEA_LINK_M1           0x60040
#define  PIPEA_LINK_M1_OFFSET   0
#define PIPEA_LINK_N1           0x60044
#define  PIPEA_LINK_N1_OFFSET   0

#define PIPEA_LINK_M2           0x60048
#define  PIPEA_LINK_M2_OFFSET   0
#define PIPEA_LINK_N2           0x6004c
#define  PIPEA_LINK_N2_OFFSET   0

/* PIPEB timing regs are same start from 0x61000 */

#define PIPEB_DATA_M1           0x61030
#define  PIPEB_DATA_M1_OFFSET   0
#define PIPEB_DATA_N1           0x61034
#define  PIPEB_DATA_N1_OFFSET   0

#define PIPEB_DATA_M2           0x61038
#define  PIPEB_DATA_M2_OFFSET   0
#define PIPEB_DATA_N2           0x6103c
#define  PIPEB_DATA_N2_OFFSET   0

#define PIPEB_LINK_M1           0x61040
#define  PIPEB_LINK_M1_OFFSET   0
#define PIPEB_LINK_N1           0x61044
#define  PIPEB_LINK_N1_OFFSET   0

#define PIPEB_LINK_M2           0x61048
#define  PIPEB_LINK_M2_OFFSET   0
#define PIPEB_LINK_N2           0x6104c
#define  PIPEB_LINK_N2_OFFSET   0

/* CPU panel fitter */
#define PFA_CTL_1               0x68080
#define PFB_CTL_1               0x68880
#define  PF_ENABLE              (1<<31)
#define  PF_FILTER_MASK         (3<<23)
#define  PF_FILTER_PROGRAMMED   (0<<23)
#define  PF_FILTER_MED_3x3      (1<<23)
#define  PF_FILTER_EDGE_ENHANCE (2<<23)
#define  PF_FILTER_EDGE_SOFTEN  (3<<23)
#define PFA_WIN_SZ              0x68074
#define PFB_WIN_SZ              0x68874
#define PFA_WIN_POS             0x68070
#define PFB_WIN_POS             0x68870

/* legacy palette */
#define LGC_PALETTE_A           0x4a000
#define LGC_PALETTE_B           0x4a800

/* interrupts */
#define DE_MASTER_IRQ_CONTROL   (1 << 31)
#define DE_SPRITEB_FLIP_DONE    (1 << 29)
#define DE_SPRITEA_FLIP_DONE    (1 << 28)
#define DE_PLANEB_FLIP_DONE     (1 << 27)
#define DE_PLANEA_FLIP_DONE     (1 << 26)
#define DE_PCU_EVENT            (1 << 25)
#define DE_GTT_FAULT            (1 << 24)
#define DE_POISON               (1 << 23)
#define DE_PERFORM_COUNTER      (1 << 22)
#define DE_PCH_EVENT            (1 << 21)
#define DE_AUX_CHANNEL_A        (1 << 20)
#define DE_DP_A_HOTPLUG         (1 << 19)
#define DE_GSE                  (1 << 18)
#define DE_PIPEB_VBLANK         (1 << 15)
#define DE_PIPEB_EVEN_FIELD     (1 << 14)
#define DE_PIPEB_ODD_FIELD      (1 << 13)
#define DE_PIPEB_LINE_COMPARE   (1 << 12)
#define DE_PIPEB_VSYNC          (1 << 11)
#define DE_PIPEB_FIFO_UNDERRUN  (1 << 8)
#define DE_PIPEA_VBLANK         (1 << 7)
#define DE_PIPEA_EVEN_FIELD     (1 << 6)
#define DE_PIPEA_ODD_FIELD      (1 << 5)
#define DE_PIPEA_LINE_COMPARE   (1 << 4)
#define DE_PIPEA_VSYNC          (1 << 3)
#define DE_PIPEA_FIFO_UNDERRUN  (1 << 0)

#define DEISR   0x44000
#define DEIMR   0x44004
#define DEIIR   0x44008
#define DEIER   0x4400c

/* GT interrupt */
#define GT_SYNC_STATUS          (1 << 2)
#define GT_USER_INTERRUPT       (1 << 0)

#define GTISR   0x44010
#define GTIMR   0x44014
#define GTIIR   0x44018
#define GTIER   0x4401c

#define DISP_ARB_CTL    0x45000
#define  DISP_TILE_SURFACE_SWIZZLING    (1<<13)

/* PCH */

/* south display engine interrupt */
#define SDE_CRT_HOTPLUG         (1 << 11)
#define SDE_PORTD_HOTPLUG       (1 << 10)
#define SDE_PORTC_HOTPLUG       (1 << 9)
#define SDE_PORTB_HOTPLUG       (1 << 8)
#define SDE_SDVOB_HOTPLUG       (1 << 6)

#define SDEISR  0xc4000
#define SDEIMR  0xc4004
#define SDEIIR  0xc4008
#define SDEIER  0xc400c

/* digital port hotplug */
#define PCH_PORT_HOTPLUG        0xc4030
#define PORTD_HOTPLUG_ENABLE            (1 << 20)
#define PORTD_PULSE_DURATION_2ms        (0)
#define PORTD_PULSE_DURATION_4_5ms      (1 << 18)
#define PORTD_PULSE_DURATION_6ms        (2 << 18)
#define PORTD_PULSE_DURATION_100ms      (3 << 18)
#define PORTD_HOTPLUG_NO_DETECT         (0)
#define PORTD_HOTPLUG_SHORT_DETECT      (1 << 16)
#define PORTD_HOTPLUG_LONG_DETECT       (1 << 17)
#define PORTC_HOTPLUG_ENABLE            (1 << 12)
#define PORTC_PULSE_DURATION_2ms        (0)
#define PORTC_PULSE_DURATION_4_5ms      (1 << 10)
#define PORTC_PULSE_DURATION_6ms        (2 << 10)
#define PORTC_PULSE_DURATION_100ms      (3 << 10)
#define PORTC_HOTPLUG_NO_DETECT         (0)
#define PORTC_HOTPLUG_SHORT_DETECT      (1 << 8)
#define PORTC_HOTPLUG_LONG_DETECT       (1 << 9)
#define PORTB_HOTPLUG_ENABLE            (1 << 4)
#define PORTB_PULSE_DURATION_2ms        (0)
#define PORTB_PULSE_DURATION_4_5ms      (1 << 2)
#define PORTB_PULSE_DURATION_6ms        (2 << 2)
#define PORTB_PULSE_DURATION_100ms      (3 << 2)
#define PORTB_HOTPLUG_NO_DETECT         (0)
#define PORTB_HOTPLUG_SHORT_DETECT      (1 << 0)
#define PORTB_HOTPLUG_LONG_DETECT       (1 << 1)

#define PCH_GPIOA               0xc5010
#define PCH_GPIOB               0xc5014
#define PCH_GPIOC               0xc5018
#define PCH_GPIOD               0xc501c
#define PCH_GPIOE               0xc5020
#define PCH_GPIOF               0xc5024

#define PCH_DPLL_A              0xc6014
#define PCH_DPLL_B              0xc6018

#define PCH_FPA0                0xc6040
#define PCH_FPA1                0xc6044
#define PCH_FPB0                0xc6048
#define PCH_FPB1                0xc604c

#define PCH_DPLL_TEST           0xc606c

#define PCH_DREF_CONTROL        0xC6200
#define  DREF_CONTROL_MASK      0x7fc3
#define  DREF_CPU_SOURCE_OUTPUT_DISABLE         (0<<13)
#define  DREF_CPU_SOURCE_OUTPUT_DOWNSPREAD      (2<<13)
#define  DREF_CPU_SOURCE_OUTPUT_NONSPREAD       (3<<13)
#define  DREF_CPU_SOURCE_OUTPUT_MASK            (3<<13)
#define  DREF_SSC_SOURCE_DISABLE                (0<<11)
#define  DREF_SSC_SOURCE_ENABLE                 (2<<11)
#define  DREF_SSC_SOURCE_MASK                   (3<<11)
#define  DREF_NONSPREAD_SOURCE_DISABLE          (0<<9)
#define  DREF_NONSPREAD_CK505_ENABLE            (1<<9)
#define  DREF_NONSPREAD_SOURCE_ENABLE           (2<<9)
#define  DREF_NONSPREAD_SOURCE_MASK             (3<<9)
#define  DREF_SUPERSPREAD_SOURCE_DISABLE        (0<<7)
#define  DREF_SUPERSPREAD_SOURCE_ENABLE         (2<<7)
#define  DREF_SSC4_DOWNSPREAD                   (0<<6)
#define  DREF_SSC4_CENTERSPREAD                 (1<<6)
#define  DREF_SSC1_DISABLE                      (0<<1)
#define  DREF_SSC1_ENABLE                       (1<<1)
#define  DREF_SSC4_DISABLE                      (0)
#define  DREF_SSC4_ENABLE                       (1)

#define PCH_RAWCLK_FREQ         0xc6204
#define  FDL_TP1_TIMER_SHIFT    12
#define  FDL_TP1_TIMER_MASK     (3<<12)
#define  FDL_TP2_TIMER_SHIFT    10
#define  FDL_TP2_TIMER_MASK     (3<<10)
#define  RAWCLK_FREQ_MASK       0x3ff

#define PCH_DPLL_TMR_CFG        0xc6208

#define PCH_SSC4_PARMS          0xc6210
#define PCH_SSC4_AUX_PARMS      0xc6214

/* transcoder */

#define TRANS_HTOTAL_A          0xe0000
#define  TRANS_HTOTAL_SHIFT     16
#define  TRANS_HACTIVE_SHIFT    0
#define TRANS_HBLANK_A          0xe0004
#define  TRANS_HBLANK_END_SHIFT 16
#define  TRANS_HBLANK_START_SHIFT 0
#define TRANS_HSYNC_A           0xe0008
#define  TRANS_HSYNC_END_SHIFT  16
#define  TRANS_HSYNC_START_SHIFT 0
#define TRANS_VTOTAL_A          0xe000c
#define  TRANS_VTOTAL_SHIFT     16
#define  TRANS_VACTIVE_SHIFT    0
#define TRANS_VBLANK_A          0xe0010
#define  TRANS_VBLANK_END_SHIFT 16
#define  TRANS_VBLANK_START_SHIFT 0
#define TRANS_VSYNC_A           0xe0014
#define  TRANS_VSYNC_END_SHIFT  16
#define  TRANS_VSYNC_START_SHIFT 0

#define TRANSA_DATA_M1          0xe0030
#define TRANSA_DATA_N1          0xe0034
#define TRANSA_DATA_M2          0xe0038
#define TRANSA_DATA_N2          0xe003c
#define TRANSA_DP_LINK_M1       0xe0040
#define TRANSA_DP_LINK_N1       0xe0044
#define TRANSA_DP_LINK_M2       0xe0048
#define TRANSA_DP_LINK_N2       0xe004c

#define TRANS_HTOTAL_B          0xe1000
#define TRANS_HBLANK_B          0xe1004
#define TRANS_HSYNC_B           0xe1008
#define TRANS_VTOTAL_B          0xe100c
#define TRANS_VBLANK_B          0xe1010
#define TRANS_VSYNC_B           0xe1014

#define TRANSB_DATA_M1          0xe1030
#define TRANSB_DATA_N1          0xe1034
#define TRANSB_DATA_M2          0xe1038
#define TRANSB_DATA_N2          0xe103c
#define TRANSB_DP_LINK_M1       0xe1040
#define TRANSB_DP_LINK_N1       0xe1044
#define TRANSB_DP_LINK_M2       0xe1048
#define TRANSB_DP_LINK_N2       0xe104c

#define TRANSACONF              0xf0008
#define TRANSBCONF              0xf1008
#define  TRANS_DISABLE          (0<<31)
#define  TRANS_ENABLE           (1<<31)
#define  TRANS_STATE_MASK       (1<<30)
#define  TRANS_STATE_DISABLE    (0<<30)
#define  TRANS_STATE_ENABLE     (1<<30)
#define  TRANS_FSYNC_DELAY_HB1  (0<<27)
#define  TRANS_FSYNC_DELAY_HB2  (1<<27)
#define  TRANS_FSYNC_DELAY_HB3  (2<<27)
#define  TRANS_FSYNC_DELAY_HB4  (3<<27)
#define  TRANS_DP_AUDIO_ONLY    (1<<26)
#define  TRANS_DP_VIDEO_AUDIO   (0<<26)
#define  TRANS_PROGRESSIVE      (0<<21)
#define  TRANS_8BPC             (0<<5)
#define  TRANS_10BPC            (1<<5)
#define  TRANS_6BPC             (2<<5)
#define  TRANS_12BPC            (3<<5)

#define FDI_RXA_CHICKEN         0xc200c
#define FDI_RXB_CHICKEN         0xc2010
#define  FDI_RX_PHASE_SYNC_POINTER_ENABLE       (1)

/* CPU: FDI_TX */
#define FDI_TXA_CTL             0x60100
#define FDI_TXB_CTL             0x61100
#define  FDI_TX_DISABLE         (0<<31)
#define  FDI_TX_ENABLE          (1<<31)
#define  FDI_LINK_TRAIN_PATTERN_1       (0<<28)
#define  FDI_LINK_TRAIN_PATTERN_2       (1<<28)
#define  FDI_LINK_TRAIN_PATTERN_IDLE    (2<<28)
#define  FDI_LINK_TRAIN_NONE            (3<<28)
#define  FDI_LINK_TRAIN_VOLTAGE_0_4V    (0<<25)
#define  FDI_LINK_TRAIN_VOLTAGE_0_6V    (1<<25)
#define  FDI_LINK_TRAIN_VOLTAGE_0_8V    (2<<25)
#define  FDI_LINK_TRAIN_VOLTAGE_1_2V    (3<<25)
#define  FDI_LINK_TRAIN_PRE_EMPHASIS_NONE (0<<22)
#define  FDI_LINK_TRAIN_PRE_EMPHASIS_1_5X (1<<22)
#define  FDI_LINK_TRAIN_PRE_EMPHASIS_2X   (2<<22)
#define  FDI_LINK_TRAIN_PRE_EMPHASIS_3X   (3<<22)
#define  FDI_DP_PORT_WIDTH_X1           (0<<19)
#define  FDI_DP_PORT_WIDTH_X2           (1<<19)
#define  FDI_DP_PORT_WIDTH_X3           (2<<19)
#define  FDI_DP_PORT_WIDTH_X4           (3<<19)
#define  FDI_TX_ENHANCE_FRAME_ENABLE    (1<<18)
/* IGDNG: hardwired to 1 */
#define  FDI_TX_PLL_ENABLE              (1<<14)
/* both Tx and Rx */
#define  FDI_SCRAMBLING_ENABLE          (0<<7)
#define  FDI_SCRAMBLING_DISABLE         (1<<7)

/* FDI_RX, FDI_X is hard-wired to Transcoder_X */
#define FDI_RXA_CTL             0xf000c
#define FDI_RXB_CTL             0xf100c
#define  FDI_RX_ENABLE          (1<<31)
#define  FDI_RX_DISABLE         (0<<31)
/* train, dp width same as FDI_TX */
#define  FDI_DP_PORT_WIDTH_X8           (7<<19)
#define  FDI_8BPC                       (0<<16)
#define  FDI_10BPC                      (1<<16)
#define  FDI_6BPC                       (2<<16)
#define  FDI_12BPC                      (3<<16)
#define  FDI_LINK_REVERSE_OVERWRITE     (1<<15)
#define  FDI_DMI_LINK_REVERSE_MASK      (1<<14)
#define  FDI_RX_PLL_ENABLE              (1<<13)
#define  FDI_FS_ERR_CORRECT_ENABLE      (1<<11)
#define  FDI_FE_ERR_CORRECT_ENABLE      (1<<10)
#define  FDI_FS_ERR_REPORT_ENABLE       (1<<9)
#define  FDI_FE_ERR_REPORT_ENABLE       (1<<8)
#define  FDI_RX_ENHANCE_FRAME_ENABLE    (1<<6)
#define  FDI_SEL_RAWCLK                 (0<<4)
#define  FDI_SEL_PCDCLK                 (1<<4)

#define FDI_RXA_MISC            0xf0010
#define FDI_RXB_MISC            0xf1010
#define FDI_RXA_TUSIZE1         0xf0030
#define FDI_RXA_TUSIZE2         0xf0038
#define FDI_RXB_TUSIZE1         0xf1030
#define FDI_RXB_TUSIZE2         0xf1038

/* FDI_RX interrupt register format */
#define FDI_RX_INTER_LANE_ALIGN         (1<<10)
#define FDI_RX_SYMBOL_LOCK              (1<<9) /* train 2 */
#define FDI_RX_BIT_LOCK                 (1<<8) /* train 1 */
#define FDI_RX_TRAIN_PATTERN_2_FAIL     (1<<7)
#define FDI_RX_FS_CODE_ERR              (1<<6)
#define FDI_RX_FE_CODE_ERR              (1<<5)
#define FDI_RX_SYMBOL_ERR_RATE_ABOVE    (1<<4)
#define FDI_RX_HDCP_LINK_FAIL           (1<<3)
#define FDI_RX_PIXEL_FIFO_OVERFLOW      (1<<2)
#define FDI_RX_CROSS_CLOCK_OVERFLOW     (1<<1)
#define FDI_RX_SYMBOL_QUEUE_OVERFLOW    (1<<0)

#define FDI_RXA_IIR             0xf0014
#define FDI_RXA_IMR             0xf0018
#define FDI_RXB_IIR             0xf1014
#define FDI_RXB_IMR             0xf1018

#define FDI_PLL_CTL_1           0xfe000
#define FDI_PLL_CTL_2           0xfe004

/* CRT */
#define PCH_ADPA                0xe1100
#define  ADPA_TRANS_SELECT_MASK (1<<30)
#define  ADPA_TRANS_A_SELECT    0
#define  ADPA_TRANS_B_SELECT    (1<<30)
#define  ADPA_CRT_HOTPLUG_MASK  0x03ff0000 /* bit 25-16 */
#define  ADPA_CRT_HOTPLUG_MONITOR_NONE  (0<<24)
#define  ADPA_CRT_HOTPLUG_MONITOR_MASK  (3<<24)
#define  ADPA_CRT_HOTPLUG_MONITOR_COLOR (3<<24)
#define  ADPA_CRT_HOTPLUG_MONITOR_MONO  (2<<24)
#define  ADPA_CRT_HOTPLUG_ENABLE        (1<<23)
#define  ADPA_CRT_HOTPLUG_PERIOD_64     (0<<22)
#define  ADPA_CRT_HOTPLUG_PERIOD_128    (1<<22)
#define  ADPA_CRT_HOTPLUG_WARMUP_5MS    (0<<21)
#define  ADPA_CRT_HOTPLUG_WARMUP_10MS   (1<<21)
#define  ADPA_CRT_HOTPLUG_SAMPLE_2S     (0<<20)
#define  ADPA_CRT_HOTPLUG_SAMPLE_4S     (1<<20)
#define  ADPA_CRT_HOTPLUG_VOLTAGE_40    (0<<18)
#define  ADPA_CRT_HOTPLUG_VOLTAGE_50    (1<<18)
#define  ADPA_CRT_HOTPLUG_VOLTAGE_60    (2<<18)
#define  ADPA_CRT_HOTPLUG_VOLTAGE_70    (3<<18)
#define  ADPA_CRT_HOTPLUG_VOLREF_325MV  (0<<17)
#define  ADPA_CRT_HOTPLUG_VOLREF_475MV  (1<<17)
#define  ADPA_CRT_HOTPLUG_FORCE_TRIGGER (1<<16)

/* or SDVOB */
#define HDMIB   0xe1140
#define  PORT_ENABLE    (1 << 31)
#define  TRANSCODER_A   (0)
#define  TRANSCODER_B   (1 << 30)
#define  COLOR_FORMAT_8bpc      (0)
#define  COLOR_FORMAT_12bpc     (3 << 26)
#define  SDVOB_HOTPLUG_ENABLE   (1 << 23)
#define  SDVO_ENCODING          (0)
#define  TMDS_ENCODING          (2 << 10)
#define  NULL_PACKET_VSYNC_ENABLE       (1 << 9)
#define  SDVOB_BORDER_ENABLE    (1 << 7)
#define  AUDIO_ENABLE           (1 << 6)
#define  VSYNC_ACTIVE_HIGH      (1 << 4)
#define  HSYNC_ACTIVE_HIGH      (1 << 3)
#define  PORT_DETECTED          (1 << 2)

#define HDMIC   0xe1150
#define HDMID   0xe1160

#define PCH_LVDS        0xe1180
#define  LVDS_DETECTED  (1 << 1)

#define BLC_PWM_CPU_CTL2        0x48250
#define  PWM_ENABLE             (1 << 31)
#define  PWM_PIPE_A             (0 << 29)
#define  PWM_PIPE_B             (1 << 29)
#define BLC_PWM_CPU_CTL         0x48254

#define BLC_PWM_PCH_CTL1        0xc8250
#define  PWM_PCH_ENABLE         (1 << 31)
#define  PWM_POLARITY_ACTIVE_LOW        (1 << 29)
#define  PWM_POLARITY_ACTIVE_HIGH       (0 << 29)
#define  PWM_POLARITY_ACTIVE_LOW2       (1 << 28)
#define  PWM_POLARITY_ACTIVE_HIGH2      (0 << 28)

#define BLC_PWM_PCH_CTL2        0xc8254

#define PCH_PP_STATUS           0xc7200
#define PCH_PP_CONTROL          0xc7204
#define  EDP_FORCE_VDD          (1 << 3)
#define  EDP_BLC_ENABLE         (1 << 2)
#define  PANEL_POWER_RESET      (1 << 1)
#define  PANEL_POWER_OFF        (0 << 0)
#define  PANEL_POWER_ON         (1 << 0)
#define PCH_PP_ON_DELAYS        0xc7208
#define  EDP_PANEL              (1 << 30)
#define PCH_PP_OFF_DELAYS       0xc720c
#define PCH_PP_DIVISOR          0xc7210

#define PCH_DP_B                0xe4100
#define PCH_DPB_AUX_CH_CTL      0xe4110
#define PCH_DPB_AUX_CH_DATA1    0xe4114
#define PCH_DPB_AUX_CH_DATA2    0xe4118
#define PCH_DPB_AUX_CH_DATA3    0xe411c
#define PCH_DPB_AUX_CH_DATA4    0xe4120
#define PCH_DPB_AUX_CH_DATA5    0xe4124

#define PCH_DP_C                0xe4200
#define PCH_DPC_AUX_CH_CTL      0xe4210
#define PCH_DPC_AUX_CH_DATA1    0xe4214
#define PCH_DPC_AUX_CH_DATA2    0xe4218
#define PCH_DPC_AUX_CH_DATA3    0xe421c
#define PCH_DPC_AUX_CH_DATA4    0xe4220
#define PCH_DPC_AUX_CH_DATA5    0xe4224

#define PCH_DP_D                0xe4300
#define PCH_DPD_AUX_CH_CTL      0xe4310
#define PCH_DPD_AUX_CH_DATA1    0xe4314
#define PCH_DPD_AUX_CH_DATA2    0xe4318
#define PCH_DPD_AUX_CH_DATA3    0xe431c
#define PCH_DPD_AUX_CH_DATA4    0xe4320
#define PCH_DPD_AUX_CH_DATA5    0xe4324

#endif /* _I915_REG_H_ */