drivers/gpu/drm/amd/display/dc/dce/dce_link_encoder.c

   1 /*
   2  * Copyright 2012-15 Advanced Micro Devices, Inc.
   3  *
   4  * Permission is hereby granted, free of charge, to any person obtaining a
   5  * copy of this software and associated documentation files (the "Software"),
   6  * to deal in the Software without restriction, including without limitation
   7  * the rights to use, copy, modify, merge, publish, distribute, sublicense,
   8  * and/or sell copies of the Software, and to permit persons to whom the
   9  * Software is furnished to do so, subject to the following conditions:
  10  *
  11  * The above copyright notice and this permission notice shall be included in
  12  * all copies or substantial portions of the Software.
  13  *
  14  * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
  15  * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
  16  * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
  17  * THE COPYRIGHT HOLDER(S) OR AUTHOR(S) BE LIABLE FOR ANY CLAIM, DAMAGES OR
  18  * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
  19  * ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
  20  * OTHER DEALINGS IN THE SOFTWARE.
  21  *
  22  * Authors: AMD
  23  *
  24  */
  25
  26 #include "reg_helper.h"
  27
  28 #include "core_types.h"
  29 #include "link_encoder.h"
  30 #include "dce_link_encoder.h"
  31 #include "stream_encoder.h"
  32 #include "i2caux_interface.h"
  33 #include "dc_bios_types.h"
  34
  35 #include "gpio_service_interface.h"
  36
  37 #include "dce/dce_11_0_d.h"
  38 #include "dce/dce_11_0_sh_mask.h"
  39 #include "dce/dce_11_0_enum.h"
  40
  41 #ifndef DMU_MEM_PWR_CNTL__DMCU_IRAM_MEM_PWR_STATE__SHIFT
  42 #define DMU_MEM_PWR_CNTL__DMCU_IRAM_MEM_PWR_STATE__SHIFT 0xa
  43 #endif
  44
  45 #ifndef DMU_MEM_PWR_CNTL__DMCU_IRAM_MEM_PWR_STATE_MASK
  46 #define DMU_MEM_PWR_CNTL__DMCU_IRAM_MEM_PWR_STATE_MASK 0x00000400L
  47 #endif
  48
  49 #ifndef HPD0_DC_HPD_CONTROL__DC_HPD_EN_MASK
  50 #define HPD0_DC_HPD_CONTROL__DC_HPD_EN_MASK  0x10000000L
  51 #endif
  52
  53 #ifndef HPD0_DC_HPD_CONTROL__DC_HPD_EN__SHIFT
  54 #define HPD0_DC_HPD_CONTROL__DC_HPD_EN__SHIFT  0x1c
  55 #endif
  56
  57 #define CTX \
  58         enc110->base.ctx
  59
  60 #define REG(reg)\
  61         (enc110->link_regs->reg)
  62
  63 #define AUX_REG(reg)\
  64         (enc110->aux_regs->reg)
  65
  66 #define HPD_REG(reg)\
  67         (enc110->hpd_regs->reg)
  68
  69 #define DEFAULT_AUX_MAX_DATA_SIZE 16
  70 #define AUX_MAX_DEFER_WRITE_RETRY 20
  71 /*
  72  * @brief
  73  * Trigger Source Select
  74  * ASIC-dependent, actual values for register programming
  75  */
  76 #define DCE110_DIG_FE_SOURCE_SELECT_INVALID 0x0
  77 #define DCE110_DIG_FE_SOURCE_SELECT_DIGA 0x1
  78 #define DCE110_DIG_FE_SOURCE_SELECT_DIGB 0x2
  79 #define DCE110_DIG_FE_SOURCE_SELECT_DIGC 0x4
  80 #define DCE110_DIG_FE_SOURCE_SELECT_DIGD 0x08
  81 #define DCE110_DIG_FE_SOURCE_SELECT_DIGE 0x10
  82 #define DCE110_DIG_FE_SOURCE_SELECT_DIGF 0x20
  83 #define DCE110_DIG_FE_SOURCE_SELECT_DIGG 0x40
  84
  85 enum {
  86         DP_MST_UPDATE_MAX_RETRY = 50
  87 };
  88
  89 #define DIG_REG(reg)\
  90         (reg + enc110->offsets.dig)
  91
  92 #define DP_REG(reg)\
  93         (reg + enc110->offsets.dp)
  94
  95 static const struct link_encoder_funcs dce110_lnk_enc_funcs = {
  96         .validate_output_with_stream =
  97                 dce110_link_encoder_validate_output_with_stream,
  98         .hw_init = dce110_link_encoder_hw_init,
  99         .setup = dce110_link_encoder_setup,
 100         .enable_tmds_output = dce110_link_encoder_enable_tmds_output,
 101         .enable_dp_output = dce110_link_encoder_enable_dp_output,
 102         .enable_dp_mst_output = dce110_link_encoder_enable_dp_mst_output,
 103         .disable_output = dce110_link_encoder_disable_output,
 104         .dp_set_lane_settings = dce110_link_encoder_dp_set_lane_settings,
 105         .dp_set_phy_pattern = dce110_link_encoder_dp_set_phy_pattern,
 106         .update_mst_stream_allocation_table =
 107                 dce110_link_encoder_update_mst_stream_allocation_table,
 108         .psr_program_dp_dphy_fast_training =
 109                         dce110_psr_program_dp_dphy_fast_training,
 110         .psr_program_secondary_packet = dce110_psr_program_secondary_packet,
 111         .connect_dig_be_to_fe = dce110_link_encoder_connect_dig_be_to_fe,
 112         .enable_hpd = dce110_link_encoder_enable_hpd,
 113         .disable_hpd = dce110_link_encoder_disable_hpd,
 114         .destroy = dce110_link_encoder_destroy
 115 };
 116
 117 static enum bp_result link_transmitter_control(
 118         struct dce110_link_encoder *enc110,
 119         struct bp_transmitter_control *cntl)
 120 {
 121         enum bp_result result;
 122         struct dc_bios *bp = enc110->base.ctx->dc_bios;
 123
 124         result = bp->funcs->transmitter_control(bp, cntl);
 125
 126         return result;
 127 }
 128
 129 static void enable_phy_bypass_mode(
 130         struct dce110_link_encoder *enc110,
 131         bool enable)
 132 {
 133         /* This register resides in DP back end block;
 134          * transmitter is used for the offset */
 135
 136         REG_UPDATE(DP_DPHY_CNTL, DPHY_BYPASS, enable);
 137
 138 }
 139
 140 static void disable_prbs_symbols(
 141         struct dce110_link_encoder *enc110,
 142         bool disable)
 143 {
 144         /* This register resides in DP back end block;
 145          * transmitter is used for the offset */
 146
 147         REG_UPDATE_4(DP_DPHY_CNTL,
 148                         DPHY_ATEST_SEL_LANE0, disable,
 149                         DPHY_ATEST_SEL_LANE1, disable,
 150                         DPHY_ATEST_SEL_LANE2, disable,
 151                         DPHY_ATEST_SEL_LANE3, disable);
 152 }
 153
 154 static void disable_prbs_mode(
 155         struct dce110_link_encoder *enc110)
 156 {
 157         REG_UPDATE(DP_DPHY_PRBS_CNTL, DPHY_PRBS_EN, 0);
 158 }
 159
 160 static void program_pattern_symbols(
 161         struct dce110_link_encoder *enc110,
 162         uint16_t pattern_symbols[8])
 163 {
 164         /* This register resides in DP back end block;
 165          * transmitter is used for the offset */
 166
 167         REG_SET_3(DP_DPHY_SYM0, 0,
 168                         DPHY_SYM1, pattern_symbols[0],
 169                         DPHY_SYM2, pattern_symbols[1],
 170                         DPHY_SYM3, pattern_symbols[2]);
 171
 172         /* This register resides in DP back end block;
 173          * transmitter is used for the offset */
 174
 175         REG_SET_3(DP_DPHY_SYM1, 0,
 176                         DPHY_SYM4, pattern_symbols[3],
 177                         DPHY_SYM5, pattern_symbols[4],
 178                         DPHY_SYM6, pattern_symbols[5]);
 179
 180         /* This register resides in DP back end block;
 181          * transmitter is used for the offset */
 182
 183         REG_SET_2(DP_DPHY_SYM2, 0,
 184                         DPHY_SYM7, pattern_symbols[6],
 185                         DPHY_SYM8, pattern_symbols[7]);
 186 }
 187
 188 static void set_dp_phy_pattern_d102(
 189         struct dce110_link_encoder *enc110)
 190 {
 191         /* Disable PHY Bypass mode to setup the test pattern */
 192         enable_phy_bypass_mode(enc110, false);
 193
 194         /* For 10-bit PRBS or debug symbols
 195          * please use the following sequence: */
 196
 197         /* Enable debug symbols on the lanes */
 198
 199         disable_prbs_symbols(enc110, true);
 200
 201         /* Disable PRBS mode */
 202         disable_prbs_mode(enc110);
 203
 204         /* Program debug symbols to be output */
 205         {
 206                 uint16_t pattern_symbols[8] = {
 207                         0x2AA, 0x2AA, 0x2AA, 0x2AA,
 208                         0x2AA, 0x2AA, 0x2AA, 0x2AA
 209                 };
 210
 211                 program_pattern_symbols(enc110, pattern_symbols);
 212         }
 213
 214         /* Enable phy bypass mode to enable the test pattern */
 215
 216         enable_phy_bypass_mode(enc110, true);
 217 }
 218
 219 static void set_link_training_complete(
 220         struct dce110_link_encoder *enc110,
 221         bool complete)
 222 {
 223         /* This register resides in DP back end block;
 224          * transmitter is used for the offset */
 225
 226         REG_UPDATE(DP_LINK_CNTL, DP_LINK_TRAINING_COMPLETE, complete);
 227
 228 }
 229
 230 void dce110_link_encoder_set_dp_phy_pattern_training_pattern(
 231         struct link_encoder *enc,
 232         uint32_t index)
 233 {
 234         struct dce110_link_encoder *enc110 = TO_DCE110_LINK_ENC(enc);
 235         /* Write Training Pattern */
 236
 237         REG_WRITE(DP_DPHY_TRAINING_PATTERN_SEL, index);
 238
 239         /* Set HW Register Training Complete to false */
 240
 241         set_link_training_complete(enc110, false);
 242
 243         /* Disable PHY Bypass mode to output Training Pattern */
 244
 245         enable_phy_bypass_mode(enc110, false);
 246
 247         /* Disable PRBS mode */
 248         disable_prbs_mode(enc110);
 249 }
 250
 251 static void setup_panel_mode(
 252         struct dce110_link_encoder *enc110,
 253         enum dp_panel_mode panel_mode)
 254 {
 255         uint32_t value;
 256
 257         ASSERT(REG(DP_DPHY_INTERNAL_CTRL));
 258         value = REG_READ(DP_DPHY_INTERNAL_CTRL);
 259
 260         switch (panel_mode) {
 261         case DP_PANEL_MODE_EDP:
 262                 value = 0x1;
 263                 break;
 264         case DP_PANEL_MODE_SPECIAL:
 265                 value = 0x11;
 266                 break;
 267         default:
 268                 value = 0x0;
 269                 break;
 270         }
 271
 272         REG_WRITE(DP_DPHY_INTERNAL_CTRL, value);
 273 }
 274
 275 static void set_dp_phy_pattern_symbol_error(
 276         struct dce110_link_encoder *enc110)
 277 {
 278         /* Disable PHY Bypass mode to setup the test pattern */
 279         enable_phy_bypass_mode(enc110, false);
 280
 281         /* program correct panel mode*/
 282         setup_panel_mode(enc110, DP_PANEL_MODE_DEFAULT);
 283
 284         /* A PRBS23 pattern is used for most DP electrical measurements. */
 285
 286         /* Enable PRBS symbols on the lanes */
 287         disable_prbs_symbols(enc110, false);
 288
 289         /* For PRBS23 Set bit DPHY_PRBS_SEL=1 and Set bit DPHY_PRBS_EN=1 */
 290         REG_UPDATE_2(DP_DPHY_PRBS_CNTL,
 291                         DPHY_PRBS_SEL, 1,
 292                         DPHY_PRBS_EN, 1);
 293
 294         /* Enable phy bypass mode to enable the test pattern */
 295         enable_phy_bypass_mode(enc110, true);
 296 }
 297
 298 static void set_dp_phy_pattern_prbs7(
 299         struct dce110_link_encoder *enc110)
 300 {
 301         /* Disable PHY Bypass mode to setup the test pattern */
 302         enable_phy_bypass_mode(enc110, false);
 303
 304         /* A PRBS7 pattern is used for most DP electrical measurements. */
 305
 306         /* Enable PRBS symbols on the lanes */
 307         disable_prbs_symbols(enc110, false);
 308
 309         /* For PRBS7 Set bit DPHY_PRBS_SEL=0 and Set bit DPHY_PRBS_EN=1 */
 310         REG_UPDATE_2(DP_DPHY_PRBS_CNTL,
 311                         DPHY_PRBS_SEL, 0,
 312                         DPHY_PRBS_EN, 1);
 313
 314         /* Enable phy bypass mode to enable the test pattern */
 315         enable_phy_bypass_mode(enc110, true);
 316 }
 317
 318 static void set_dp_phy_pattern_80bit_custom(
 319         struct dce110_link_encoder *enc110,
 320         const uint8_t *pattern)
 321 {
 322         /* Disable PHY Bypass mode to setup the test pattern */
 323         enable_phy_bypass_mode(enc110, false);
 324
 325         /* Enable debug symbols on the lanes */
 326
 327         disable_prbs_symbols(enc110, true);
 328
 329         /* Enable PHY bypass mode to enable the test pattern */
 330         /* TODO is it really needed ? */
 331
 332         enable_phy_bypass_mode(enc110, true);
 333
 334         /* Program 80 bit custom pattern */
 335         {
 336                 uint16_t pattern_symbols[8];
 337
 338                 pattern_symbols[0] =
 339                         ((pattern[1] & 0x03) << 8) | pattern[0];
 340                 pattern_symbols[1] =
 341                         ((pattern[2] & 0x0f) << 6) | ((pattern[1] >> 2) & 0x3f);
 342                 pattern_symbols[2] =
 343                         ((pattern[3] & 0x3f) << 4) | ((pattern[2] >> 4) & 0x0f);
 344                 pattern_symbols[3] =
 345                         (pattern[4] << 2) | ((pattern[3] >> 6) & 0x03);
 346                 pattern_symbols[4] =
 347                         ((pattern[6] & 0x03) << 8) | pattern[5];
 348                 pattern_symbols[5] =
 349                         ((pattern[7] & 0x0f) << 6) | ((pattern[6] >> 2) & 0x3f);
 350                 pattern_symbols[6] =
 351                         ((pattern[8] & 0x3f) << 4) | ((pattern[7] >> 4) & 0x0f);
 352                 pattern_symbols[7] =
 353                         (pattern[9] << 2) | ((pattern[8] >> 6) & 0x03);
 354
 355                 program_pattern_symbols(enc110, pattern_symbols);
 356         }
 357
 358         /* Enable phy bypass mode to enable the test pattern */
 359
 360         enable_phy_bypass_mode(enc110, true);
 361 }
 362
 363 static void set_dp_phy_pattern_hbr2_compliance_cp2520_2(
 364         struct dce110_link_encoder *enc110,
 365         unsigned int cp2520_pattern)
 366 {
 367
 368         /* previously there is a register DP_HBR2_EYE_PATTERN
 369          * that is enabled to get the pattern.
 370          * But it does not work with the latest spec change,
 371          * so we are programming the following registers manually.
 372          *
 373          * The following settings have been confirmed
 374          * by Nick Chorney and Sandra Liu */
 375
 376         /* Disable PHY Bypass mode to setup the test pattern */
 377
 378         enable_phy_bypass_mode(enc110, false);
 379
 380         /* Setup DIG encoder in DP SST mode */
 381         enc110->base.funcs->setup(&enc110->base, SIGNAL_TYPE_DISPLAY_PORT);
 382
 383         /* ensure normal panel mode. */
 384         setup_panel_mode(enc110, DP_PANEL_MODE_DEFAULT);
 385
 386         /* no vbid after BS (SR)
 387          * DP_LINK_FRAMING_CNTL changed history Sandra Liu
 388          * 11000260 / 11000104 / 110000FC */
 389         REG_UPDATE_3(DP_LINK_FRAMING_CNTL,
 390                         DP_IDLE_BS_INTERVAL, 0xFC,
 391                         DP_VBID_DISABLE, 1,
 392                         DP_VID_ENHANCED_FRAME_MODE, 1);
 393
 394         /* swap every BS with SR */
 395         REG_UPDATE(DP_DPHY_SCRAM_CNTL, DPHY_SCRAMBLER_BS_COUNT, 0);
 396
 397         /* select cp2520 patterns */
 398         if (REG(DP_DPHY_HBR2_PATTERN_CONTROL))
 399                 REG_UPDATE(DP_DPHY_HBR2_PATTERN_CONTROL,
 400                                 DP_DPHY_HBR2_PATTERN_CONTROL, cp2520_pattern);
 401         else
 402                 /* pre-DCE11 can only generate CP2520 pattern 2 */
 403                 ASSERT(cp2520_pattern == 2);
 404
 405         /* set link training complete */
 406         set_link_training_complete(enc110, true);
 407
 408         /* disable video stream */
 409         REG_UPDATE(DP_VID_STREAM_CNTL, DP_VID_STREAM_ENABLE, 0);
 410
 411         /* Disable PHY Bypass mode to setup the test pattern */
 412         enable_phy_bypass_mode(enc110, false);
 413 }
 414
 415 static void set_dp_phy_pattern_passthrough_mode(
 416         struct dce110_link_encoder *enc110,
 417         enum dp_panel_mode panel_mode)
 418 {
 419         /* program correct panel mode */
 420         setup_panel_mode(enc110, panel_mode);
 421
 422         /* restore LINK_FRAMING_CNTL and DPHY_SCRAMBLER_BS_COUNT
 423          * in case we were doing HBR2 compliance pattern before
 424          */
 425         REG_UPDATE_3(DP_LINK_FRAMING_CNTL,
 426                         DP_IDLE_BS_INTERVAL, 0x2000,
 427                         DP_VBID_DISABLE, 0,
 428                         DP_VID_ENHANCED_FRAME_MODE, 1);
 429
 430         REG_UPDATE(DP_DPHY_SCRAM_CNTL, DPHY_SCRAMBLER_BS_COUNT, 0x1FF);
 431
 432         /* set link training complete */
 433         set_link_training_complete(enc110, true);
 434
 435         /* Disable PHY Bypass mode to setup the test pattern */
 436         enable_phy_bypass_mode(enc110, false);
 437
 438         /* Disable PRBS mode */
 439         disable_prbs_mode(enc110);
 440 }
 441
 442 /* return value is bit-vector */
 443 static uint8_t get_frontend_source(
 444         enum engine_id engine)
 445 {
 446         switch (engine) {
 447         case ENGINE_ID_DIGA:
 448                 return DCE110_DIG_FE_SOURCE_SELECT_DIGA;
 449         case ENGINE_ID_DIGB:
 450                 return DCE110_DIG_FE_SOURCE_SELECT_DIGB;
 451         case ENGINE_ID_DIGC:
 452                 return DCE110_DIG_FE_SOURCE_SELECT_DIGC;
 453         case ENGINE_ID_DIGD:
 454                 return DCE110_DIG_FE_SOURCE_SELECT_DIGD;
 455         case ENGINE_ID_DIGE:
 456                 return DCE110_DIG_FE_SOURCE_SELECT_DIGE;
 457         case ENGINE_ID_DIGF:
 458                 return DCE110_DIG_FE_SOURCE_SELECT_DIGF;
 459         case ENGINE_ID_DIGG:
 460                 return DCE110_DIG_FE_SOURCE_SELECT_DIGG;
 461         default:
 462                 ASSERT_CRITICAL(false);
 463                 return DCE110_DIG_FE_SOURCE_SELECT_INVALID;
 464         }
 465 }
 466
 467 static void configure_encoder(
 468         struct dce110_link_encoder *enc110,
 469         const struct dc_link_settings *link_settings)
 470 {
 471         /* set number of lanes */
 472
 473         REG_SET(DP_CONFIG, 0,
 474                         DP_UDI_LANES, link_settings->lane_count - LANE_COUNT_ONE);
 475
 476         /* setup scrambler */
 477         REG_UPDATE(DP_DPHY_SCRAM_CNTL, DPHY_SCRAMBLER_ADVANCE, 1);
 478 }
 479
 480 static void aux_initialize(
 481         struct dce110_link_encoder *enc110)
 482 {
 483         struct dc_context *ctx = enc110->base.ctx;
 484         enum hpd_source_id hpd_source = enc110->base.hpd_source;
 485         uint32_t addr = AUX_REG(AUX_CONTROL);
 486         uint32_t value = dm_read_reg(ctx, addr);
 487
 488         set_reg_field_value(value, hpd_source, AUX_CONTROL, AUX_HPD_SEL);
 489         set_reg_field_value(value, 0, AUX_CONTROL, AUX_LS_READ_EN);
 490         dm_write_reg(ctx, addr, value);
 491
 492         addr = AUX_REG(AUX_DPHY_RX_CONTROL0);
 493         value = dm_read_reg(ctx, addr);
 494
 495         /* 1/4 window (the maximum allowed) */
 496         set_reg_field_value(value, 1,
 497                         AUX_DPHY_RX_CONTROL0, AUX_RX_RECEIVE_WINDOW);
 498         dm_write_reg(ctx, addr, value);
 499
 500 }
 501
 502 void dce110_psr_program_dp_dphy_fast_training(struct link_encoder *enc,
 503                         bool exit_link_training_required)
 504 {
 505         struct dce110_link_encoder *enc110 = TO_DCE110_LINK_ENC(enc);
 506
 507         if (exit_link_training_required)
 508                 REG_UPDATE(DP_DPHY_FAST_TRAINING,
 509                                 DPHY_RX_FAST_TRAINING_CAPABLE, 1);
 510         else {
 511                 REG_UPDATE(DP_DPHY_FAST_TRAINING,
 512                                 DPHY_RX_FAST_TRAINING_CAPABLE, 0);
 513                 /*In DCE 11, we are able to pre-program a Force SR register
 514                  * to be able to trigger SR symbol after 5 idle patterns
 515                  * transmitted. Upon PSR Exit, DMCU can trigger
 516                  * DPHY_LOAD_BS_COUNT_START = 1. Upon writing 1 to
 517                  * DPHY_LOAD_BS_COUNT_START and the internal counter
 518                  * reaches DPHY_LOAD_BS_COUNT, the next BS symbol will be
 519                  * replaced by SR symbol once.
 520                  */
 521
 522                 REG_UPDATE(DP_DPHY_BS_SR_SWAP_CNTL, DPHY_LOAD_BS_COUNT, 0x5);
 523         }
 524 }
 525
 526 void dce110_psr_program_secondary_packet(struct link_encoder *enc,
 527                         unsigned int sdp_transmit_line_num_deadline)
 528 {
 529         struct dce110_link_encoder *enc110 = TO_DCE110_LINK_ENC(enc);
 530
 531         REG_UPDATE_2(DP_SEC_CNTL1,
 532                 DP_SEC_GSP0_LINE_NUM, sdp_transmit_line_num_deadline,
 533                 DP_SEC_GSP0_PRIORITY, 1);
 534 }
 535
 536 static bool is_dig_enabled(const struct dce110_link_encoder *enc110)
 537 {
 538         uint32_t value;
 539
 540         REG_GET(DIG_BE_EN_CNTL, DIG_ENABLE, &value);
 541         return value;
 542 }
 543
 544 static void link_encoder_disable(struct dce110_link_encoder *enc110)
 545 {
 546         /* reset training pattern */
 547         REG_SET(DP_DPHY_TRAINING_PATTERN_SEL, 0,
 548                         DPHY_TRAINING_PATTERN_SEL, 0);
 549
 550         /* reset training complete */
 551         REG_UPDATE(DP_LINK_CNTL, DP_LINK_TRAINING_COMPLETE, 0);
 552
 553         /* reset panel mode */
 554         setup_panel_mode(enc110, DP_PANEL_MODE_DEFAULT);
 555 }
 556
 557 static void hpd_initialize(
 558         struct dce110_link_encoder *enc110)
 559 {
 560         /* Associate HPD with DIG_BE */
 561         enum hpd_source_id hpd_source = enc110->base.hpd_source;
 562
 563         REG_UPDATE(DIG_BE_CNTL, DIG_HPD_SELECT, hpd_source);
 564 }
 565
 566 bool dce110_link_encoder_validate_dvi_output(
 567         const struct dce110_link_encoder *enc110,
 568         enum signal_type connector_signal,
 569         enum signal_type signal,
 570         const struct dc_crtc_timing *crtc_timing)
 571 {
 572         uint32_t max_pixel_clock = TMDS_MAX_PIXEL_CLOCK;
 573
 574         if (signal == SIGNAL_TYPE_DVI_DUAL_LINK)
 575                 max_pixel_clock *= 2;
 576
 577         /* This handles the case of HDMI downgrade to DVI we don't want to
 578          * we don't want to cap the pixel clock if the DDI is not DVI.
 579          */
 580         if (connector_signal != SIGNAL_TYPE_DVI_DUAL_LINK &&
 581                         connector_signal != SIGNAL_TYPE_DVI_SINGLE_LINK)
 582                 max_pixel_clock = enc110->base.features.max_hdmi_pixel_clock;
 583
 584         /* DVI only support RGB pixel encoding */
 585         if (crtc_timing->pixel_encoding != PIXEL_ENCODING_RGB)
 586                 return false;
 587
 588         /*connect DVI via adpater's HDMI connector*/
 589         if ((connector_signal == SIGNAL_TYPE_DVI_SINGLE_LINK ||
 590                 connector_signal == SIGNAL_TYPE_HDMI_TYPE_A) &&
 591                 signal != SIGNAL_TYPE_HDMI_TYPE_A &&
 592                 crtc_timing->pix_clk_khz > TMDS_MAX_PIXEL_CLOCK)
 593                 return false;
 594         if (crtc_timing->pix_clk_khz < TMDS_MIN_PIXEL_CLOCK)
 595                 return false;
 596
 597         if (crtc_timing->pix_clk_khz > max_pixel_clock)
 598                 return false;
 599
 600         /* DVI supports 6/8bpp single-link and 10/16bpp dual-link */
 601         switch (crtc_timing->display_color_depth) {
 602         case COLOR_DEPTH_666:
 603         case COLOR_DEPTH_888:
 604         break;
 605         case COLOR_DEPTH_101010:
 606         case COLOR_DEPTH_161616:
 607                 if (signal != SIGNAL_TYPE_DVI_DUAL_LINK)
 608                         return false;
 609         break;
 610         default:
 611                 return false;
 612         }
 613
 614         return true;
 615 }
 616
 617 static bool dce110_link_encoder_validate_hdmi_output(
 618         const struct dce110_link_encoder *enc110,
 619         const struct dc_crtc_timing *crtc_timing,
 620         int adjusted_pix_clk_khz)
 621 {
 622         enum dc_color_depth max_deep_color =
 623                         enc110->base.features.max_hdmi_deep_color;
 624
 625         if (max_deep_color < crtc_timing->display_color_depth)
 626                 return false;
 627
 628         if (crtc_timing->display_color_depth < COLOR_DEPTH_888)
 629                 return false;
 630         if (adjusted_pix_clk_khz < TMDS_MIN_PIXEL_CLOCK)
 631                 return false;
 632
 633         if ((adjusted_pix_clk_khz == 0) ||
 634                 (adjusted_pix_clk_khz > enc110->base.features.max_hdmi_pixel_clock))
 635                 return false;
 636
 637         /* DCE11 HW does not support 420 */
 638         if (!enc110->base.features.ycbcr420_supported &&
 639                         crtc_timing->pixel_encoding == PIXEL_ENCODING_YCBCR420)
 640                 return false;
 641
 642         if (!enc110->base.features.flags.bits.HDMI_6GB_EN &&
 643                 adjusted_pix_clk_khz >= 300000)
 644                 return false;
 645         return true;
 646 }
 647
 648 bool dce110_link_encoder_validate_dp_output(
 649         const struct dce110_link_encoder *enc110,
 650         const struct dc_crtc_timing *crtc_timing)
 651 {
 652         /* default RGB only */
 653         if (crtc_timing->pixel_encoding == PIXEL_ENCODING_RGB)
 654                 return true;
 655
 656         if (enc110->base.features.flags.bits.IS_YCBCR_CAPABLE)
 657                 return true;
 658
 659         /* for DCE 8.x or later DP Y-only feature,
 660          * we need ASIC cap + FeatureSupportDPYonly, not support 666 */
 661         if (crtc_timing->flags.Y_ONLY &&
 662                 enc110->base.features.flags.bits.IS_YCBCR_CAPABLE &&
 663                 crtc_timing->display_color_depth != COLOR_DEPTH_666)
 664                 return true;
 665
 666         return false;
 667 }
 668
 669 void dce110_link_encoder_construct(
 670         struct dce110_link_encoder *enc110,
 671         const struct encoder_init_data *init_data,
 672         const struct encoder_feature_support *enc_features,
 673         const struct dce110_link_enc_registers *link_regs,
 674         const struct dce110_link_enc_aux_registers *aux_regs,
 675         const struct dce110_link_enc_hpd_registers *hpd_regs)
 676 {
 677         struct bp_encoder_cap_info bp_cap_info = {0};
 678         const struct dc_vbios_funcs *bp_funcs = init_data->ctx->dc_bios->funcs;
 679         enum bp_result result = BP_RESULT_OK;
 680
 681         enc110->base.funcs = &dce110_lnk_enc_funcs;
 682         enc110->base.ctx = init_data->ctx;
 683         enc110->base.id = init_data->encoder;
 684
 685         enc110->base.hpd_source = init_data->hpd_source;
 686         enc110->base.connector = init_data->connector;
 687
 688         enc110->base.preferred_engine = ENGINE_ID_UNKNOWN;
 689
 690         enc110->base.features = *enc_features;
 691
 692         enc110->base.transmitter = init_data->transmitter;
 693
 694         /* set the flag to indicate whether driver poll the I2C data pin
 695          * while doing the DP sink detect
 696          */
 697
 698 /*      if (dal_adapter_service_is_feature_supported(as,
 699                 FEATURE_DP_SINK_DETECT_POLL_DATA_PIN))
 700                 enc110->base.features.flags.bits.
 701                         DP_SINK_DETECT_POLL_DATA_PIN = true;*/
 702
 703         enc110->base.output_signals =
 704                 SIGNAL_TYPE_DVI_SINGLE_LINK |
 705                 SIGNAL_TYPE_DVI_DUAL_LINK |
 706                 SIGNAL_TYPE_LVDS |
 707                 SIGNAL_TYPE_DISPLAY_PORT |
 708                 SIGNAL_TYPE_DISPLAY_PORT_MST |
 709                 SIGNAL_TYPE_EDP |
 710                 SIGNAL_TYPE_HDMI_TYPE_A;
 711
 712         /* For DCE 8.0 and 8.1, by design, UNIPHY is hardwired to DIG_BE.
 713          * SW always assign DIG_FE 1:1 mapped to DIG_FE for non-MST UNIPHY.
 714          * SW assign DIG_FE to non-MST UNIPHY first and MST last. So prefer
 715          * DIG is per UNIPHY and used by SST DP, eDP, HDMI, DVI and LVDS.
 716          * Prefer DIG assignment is decided by board design.
 717          * For DCE 8.0, there are only max 6 UNIPHYs, we assume board design
 718          * and VBIOS will filter out 7 UNIPHY for DCE 8.0.
 719          * By this, adding DIGG should not hurt DCE 8.0.
 720          * This will let DCE 8.1 share DCE 8.0 as much as possible
 721          */
 722
 723         enc110->link_regs = link_regs;
 724         enc110->aux_regs = aux_regs;
 725         enc110->hpd_regs = hpd_regs;
 726
 727         switch (enc110->base.transmitter) {
 728         case TRANSMITTER_UNIPHY_A:
 729                 enc110->base.preferred_engine = ENGINE_ID_DIGA;
 730         break;
 731         case TRANSMITTER_UNIPHY_B:
 732                 enc110->base.preferred_engine = ENGINE_ID_DIGB;
 733         break;
 734         case TRANSMITTER_UNIPHY_C:
 735                 enc110->base.preferred_engine = ENGINE_ID_DIGC;
 736         break;
 737         case TRANSMITTER_UNIPHY_D:
 738                 enc110->base.preferred_engine = ENGINE_ID_DIGD;
 739         break;
 740         case TRANSMITTER_UNIPHY_E:
 741                 enc110->base.preferred_engine = ENGINE_ID_DIGE;
 742         break;
 743         case TRANSMITTER_UNIPHY_F:
 744                 enc110->base.preferred_engine = ENGINE_ID_DIGF;
 745         break;
 746         case TRANSMITTER_UNIPHY_G:
 747                 enc110->base.preferred_engine = ENGINE_ID_DIGG;
 748         break;
 749         default:
 750                 ASSERT_CRITICAL(false);
 751                 enc110->base.preferred_engine = ENGINE_ID_UNKNOWN;
 752         }
 753
 754         /* default to one to mirror Windows behavior */
 755         enc110->base.features.flags.bits.HDMI_6GB_EN = 1;
 756
 757         result = bp_funcs->get_encoder_cap_info(enc110->base.ctx->dc_bios,
 758                                                 enc110->base.id, &bp_cap_info);
 759
 760         /* Override features with DCE-specific values */
 761         if (BP_RESULT_OK == result) {
 762                 enc110->base.features.flags.bits.IS_HBR2_CAPABLE =
 763                                 bp_cap_info.DP_HBR2_EN;
 764                 enc110->base.features.flags.bits.IS_HBR3_CAPABLE =
 765                                 bp_cap_info.DP_HBR3_EN;
 766                 enc110->base.features.flags.bits.HDMI_6GB_EN = bp_cap_info.HDMI_6GB_EN;
 767         } else {
 768                 dm_logger_write(enc110->base.ctx->logger, LOG_WARNING,
 769                                 "%s: Failed to get encoder_cap_info from VBIOS with error code %d!\n",
 770                                 __func__,
 771                                 result);
 772         }
 773 }
 774
 775 bool dce110_link_encoder_validate_output_with_stream(
 776         struct link_encoder *enc,
 777         const struct dc_stream_state *stream)
 778 {
 779         struct dce110_link_encoder *enc110 = TO_DCE110_LINK_ENC(enc);
 780         bool is_valid;
 781
 782         switch (stream->signal) {
 783         case SIGNAL_TYPE_DVI_SINGLE_LINK:
 784         case SIGNAL_TYPE_DVI_DUAL_LINK:
 785                 is_valid = dce110_link_encoder_validate_dvi_output(
 786                         enc110,
 787                         stream->sink->link->connector_signal,
 788                         stream->signal,
 789                         &stream->timing);
 790         break;
 791         case SIGNAL_TYPE_HDMI_TYPE_A:
 792                 is_valid = dce110_link_encoder_validate_hdmi_output(
 793                                 enc110,
 794                                 &stream->timing,
 795                                 stream->phy_pix_clk);
 796         break;
 797         case SIGNAL_TYPE_DISPLAY_PORT:
 798         case SIGNAL_TYPE_DISPLAY_PORT_MST:
 799                 is_valid = dce110_link_encoder_validate_dp_output(
 800                                         enc110, &stream->timing);
 801         break;
 802         case SIGNAL_TYPE_EDP:
 803                 is_valid =
 804                         (stream->timing.
 805                                 pixel_encoding == PIXEL_ENCODING_RGB) ? true : false;
 806         break;
 807         case SIGNAL_TYPE_VIRTUAL:
 808                 is_valid = true;
 809                 break;
 810         default:
 811                 is_valid = false;
 812         break;
 813         }
 814
 815         return is_valid;
 816 }
 817
 818 void dce110_link_encoder_hw_init(
 819         struct link_encoder *enc)
 820 {
 821         struct dce110_link_encoder *enc110 = TO_DCE110_LINK_ENC(enc);
 822         struct dc_context *ctx = enc110->base.ctx;
 823         struct bp_transmitter_control cntl = { 0 };
 824         enum bp_result result;
 825
 826         cntl.action = TRANSMITTER_CONTROL_INIT;
 827         cntl.engine_id = ENGINE_ID_UNKNOWN;
 828         cntl.transmitter = enc110->base.transmitter;
 829         cntl.connector_obj_id = enc110->base.connector;
 830         cntl.lanes_number = LANE_COUNT_FOUR;
 831         cntl.coherent = false;
 832         cntl.hpd_sel = enc110->base.hpd_source;
 833
 834         result = link_transmitter_control(enc110, &cntl);
 835
 836         if (result != BP_RESULT_OK) {
 837                 dm_logger_write(ctx->logger, LOG_ERROR,
 838                         "%s: Failed to execute VBIOS command table!\n",
 839                         __func__);
 840                 BREAK_TO_DEBUGGER();
 841                 return;
 842         }
 843
 844         if (enc110->base.connector.id == CONNECTOR_ID_LVDS) {
 845                 cntl.action = TRANSMITTER_CONTROL_BACKLIGHT_BRIGHTNESS;
 846
 847                 result = link_transmitter_control(enc110, &cntl);
 848
 849                 ASSERT(result == BP_RESULT_OK);
 850
 851         }
 852         aux_initialize(enc110);
 853
 854         /* reinitialize HPD.
 855          * hpd_initialize() will pass DIG_FE id to HW context.
 856          * All other routine within HW context will use fe_engine_offset
 857          * as DIG_FE id even caller pass DIG_FE id.
 858          * So this routine must be called first. */
 859         hpd_initialize(enc110);
 860 }
 861
 862 void dce110_link_encoder_destroy(struct link_encoder **enc)
 863 {
 864         kfree(TO_DCE110_LINK_ENC(*enc));
 865         *enc = NULL;
 866 }
 867
 868 void dce110_link_encoder_setup(
 869         struct link_encoder *enc,
 870         enum signal_type signal)
 871 {
 872         struct dce110_link_encoder *enc110 = TO_DCE110_LINK_ENC(enc);
 873
 874         switch (signal) {
 875         case SIGNAL_TYPE_EDP:
 876         case SIGNAL_TYPE_DISPLAY_PORT:
 877                 /* DP SST */
 878                 REG_UPDATE(DIG_BE_CNTL, DIG_MODE, 0);
 879                 break;
 880         case SIGNAL_TYPE_LVDS:
 881                 /* LVDS */
 882                 REG_UPDATE(DIG_BE_CNTL, DIG_MODE, 1);
 883                 break;
 884         case SIGNAL_TYPE_DVI_SINGLE_LINK:
 885         case SIGNAL_TYPE_DVI_DUAL_LINK:
 886                 /* TMDS-DVI */
 887                 REG_UPDATE(DIG_BE_CNTL, DIG_MODE, 2);
 888                 break;
 889         case SIGNAL_TYPE_HDMI_TYPE_A:
 890                 /* TMDS-HDMI */
 891                 REG_UPDATE(DIG_BE_CNTL, DIG_MODE, 3);
 892                 break;
 893         case SIGNAL_TYPE_DISPLAY_PORT_MST:
 894                 /* DP MST */
 895                 REG_UPDATE(DIG_BE_CNTL, DIG_MODE, 5);
 896                 break;
 897         default:
 898                 ASSERT_CRITICAL(false);
 899                 /* invalid mode ! */
 900                 break;
 901         }
 902
 903 }
 904
 905 /* TODO: still need depth or just pass in adjusted pixel clock? */
 906 void dce110_link_encoder_enable_tmds_output(
 907         struct link_encoder *enc,
 908         enum clock_source_id clock_source,
 909         enum dc_color_depth color_depth,
 910         enum signal_type signal,
 911         uint32_t pixel_clock)
 912 {
 913         struct dce110_link_encoder *enc110 = TO_DCE110_LINK_ENC(enc);
 914         struct dc_context *ctx = enc110->base.ctx;
 915         struct bp_transmitter_control cntl = { 0 };
 916         enum bp_result result;
 917
 918         /* Enable the PHY */
 919
 920         cntl.action = TRANSMITTER_CONTROL_ENABLE;
 921         cntl.engine_id = enc->preferred_engine;
 922         cntl.transmitter = enc110->base.transmitter;
 923         cntl.pll_id = clock_source;
 924         cntl.signal = signal;
 925         if (cntl.signal == SIGNAL_TYPE_DVI_DUAL_LINK)
 926                 cntl.lanes_number = 8;
 927         else
 928                 cntl.lanes_number = 4;
 929
 930         cntl.hpd_sel = enc110->base.hpd_source;
 931
 932         cntl.pixel_clock = pixel_clock;
 933         cntl.color_depth = color_depth;
 934
 935         result = link_transmitter_control(enc110, &cntl);
 936
 937         if (result != BP_RESULT_OK) {
 938                 dm_logger_write(ctx->logger, LOG_ERROR,
 939                         "%s: Failed to execute VBIOS command table!\n",
 940                         __func__);
 941                 BREAK_TO_DEBUGGER();
 942         }
 943 }
 944
 945 /* enables DP PHY output */
 946 void dce110_link_encoder_enable_dp_output(
 947         struct link_encoder *enc,
 948         const struct dc_link_settings *link_settings,
 949         enum clock_source_id clock_source)
 950 {
 951         struct dce110_link_encoder *enc110 = TO_DCE110_LINK_ENC(enc);
 952         struct dc_context *ctx = enc110->base.ctx;
 953         struct bp_transmitter_control cntl = { 0 };
 954         enum bp_result result;
 955
 956         /* Enable the PHY */
 957
 958         /* number_of_lanes is used for pixel clock adjust,
 959          * but it's not passed to asic_control.
 960          * We need to set number of lanes manually.
 961          */
 962         configure_encoder(enc110, link_settings);
 963
 964         cntl.action = TRANSMITTER_CONTROL_ENABLE;
 965         cntl.engine_id = enc->preferred_engine;
 966         cntl.transmitter = enc110->base.transmitter;
 967         cntl.pll_id = clock_source;
 968         cntl.signal = SIGNAL_TYPE_DISPLAY_PORT;
 969         cntl.lanes_number = link_settings->lane_count;
 970         cntl.hpd_sel = enc110->base.hpd_source;
 971         cntl.pixel_clock = link_settings->link_rate
 972                                                 * LINK_RATE_REF_FREQ_IN_KHZ;
 973         /* TODO: check if undefined works */
 974         cntl.color_depth = COLOR_DEPTH_UNDEFINED;
 975
 976         result = link_transmitter_control(enc110, &cntl);
 977
 978         if (result != BP_RESULT_OK) {
 979                 dm_logger_write(ctx->logger, LOG_ERROR,
 980                         "%s: Failed to execute VBIOS command table!\n",
 981                         __func__);
 982                 BREAK_TO_DEBUGGER();
 983         }
 984 }
 985
 986 /* enables DP PHY output in MST mode */
 987 void dce110_link_encoder_enable_dp_mst_output(
 988         struct link_encoder *enc,
 989         const struct dc_link_settings *link_settings,
 990         enum clock_source_id clock_source)
 991 {
 992         struct dce110_link_encoder *enc110 = TO_DCE110_LINK_ENC(enc);
 993         struct dc_context *ctx = enc110->base.ctx;
 994         struct bp_transmitter_control cntl = { 0 };
 995         enum bp_result result;
 996
 997         /* Enable the PHY */
 998
 999         /* number_of_lanes is used for pixel clock adjust,
1000          * but it's not passed to asic_control.
1001          * We need to set number of lanes manually.
1002          */
1003         configure_encoder(enc110, link_settings);
1004
1005         cntl.action = TRANSMITTER_CONTROL_ENABLE;
1006         cntl.engine_id = ENGINE_ID_UNKNOWN;
1007         cntl.transmitter = enc110->base.transmitter;
1008         cntl.pll_id = clock_source;
1009         cntl.signal = SIGNAL_TYPE_DISPLAY_PORT_MST;
1010         cntl.lanes_number = link_settings->lane_count;
1011         cntl.hpd_sel = enc110->base.hpd_source;
1012         cntl.pixel_clock = link_settings->link_rate
1013                                                 * LINK_RATE_REF_FREQ_IN_KHZ;
1014         /* TODO: check if undefined works */
1015         cntl.color_depth = COLOR_DEPTH_UNDEFINED;
1016
1017         result = link_transmitter_control(enc110, &cntl);
1018
1019         if (result != BP_RESULT_OK) {
1020                 dm_logger_write(ctx->logger, LOG_ERROR,
1021                         "%s: Failed to execute VBIOS command table!\n",
1022                         __func__);
1023                 BREAK_TO_DEBUGGER();
1024         }
1025 }
1026 /*
1027  * @brief
1028  * Disable transmitter and its encoder
1029  */
1030 void dce110_link_encoder_disable_output(
1031         struct link_encoder *enc,
1032         enum signal_type signal)
1033 {
1034         struct dce110_link_encoder *enc110 = TO_DCE110_LINK_ENC(enc);
1035         struct dc_context *ctx = enc110->base.ctx;
1036         struct bp_transmitter_control cntl = { 0 };
1037         enum bp_result result;
1038
1039         if (!is_dig_enabled(enc110)) {
1040                 /* OF_SKIP_POWER_DOWN_INACTIVE_ENCODER */
1041                 return;
1042         }
1043         /* Power-down RX and disable GPU PHY should be paired.
1044          * Disabling PHY without powering down RX may cause
1045          * symbol lock loss, on which we will get DP Sink interrupt. */
1046
1047         /* There is a case for the DP active dongles
1048          * where we want to disable the PHY but keep RX powered,
1049          * for those we need to ignore DP Sink interrupt
1050          * by checking lane count that has been set
1051          * on the last do_enable_output(). */
1052
1053         /* disable transmitter */
1054         cntl.action = TRANSMITTER_CONTROL_DISABLE;
1055         cntl.transmitter = enc110->base.transmitter;
1056         cntl.hpd_sel = enc110->base.hpd_source;
1057         cntl.signal = signal;
1058         cntl.connector_obj_id = enc110->base.connector;
1059
1060         result = link_transmitter_control(enc110, &cntl);
1061
1062         if (result != BP_RESULT_OK) {
1063                 dm_logger_write(ctx->logger, LOG_ERROR,
1064                         "%s: Failed to execute VBIOS command table!\n",
1065                         __func__);
1066                 BREAK_TO_DEBUGGER();
1067                 return;
1068         }
1069
1070         /* disable encoder */
1071         if (dc_is_dp_signal(signal))
1072                 link_encoder_disable(enc110);
1073 }
1074
1075 void dce110_link_encoder_dp_set_lane_settings(
1076         struct link_encoder *enc,
1077         const struct link_training_settings *link_settings)
1078 {
1079         struct dce110_link_encoder *enc110 = TO_DCE110_LINK_ENC(enc);
1080         union dpcd_training_lane_set training_lane_set = { { 0 } };
1081         int32_t lane = 0;
1082         struct bp_transmitter_control cntl = { 0 };
1083
1084         if (!link_settings) {
1085                 BREAK_TO_DEBUGGER();
1086                 return;
1087         }
1088
1089         cntl.action = TRANSMITTER_CONTROL_SET_VOLTAGE_AND_PREEMPASIS;
1090         cntl.transmitter = enc110->base.transmitter;
1091         cntl.connector_obj_id = enc110->base.connector;
1092         cntl.lanes_number = link_settings->link_settings.lane_count;
1093         cntl.hpd_sel = enc110->base.hpd_source;
1094         cntl.pixel_clock = link_settings->link_settings.link_rate *
1095                                                 LINK_RATE_REF_FREQ_IN_KHZ;
1096
1097         for (lane = 0; lane < link_settings->link_settings.lane_count; lane++) {
1098                 /* translate lane settings */
1099
1100                 training_lane_set.bits.VOLTAGE_SWING_SET =
1101                         link_settings->lane_settings[lane].VOLTAGE_SWING;
1102                 training_lane_set.bits.PRE_EMPHASIS_SET =
1103                         link_settings->lane_settings[lane].PRE_EMPHASIS;
1104
1105                 /* post cursor 2 setting only applies to HBR2 link rate */
1106                 if (link_settings->link_settings.link_rate == LINK_RATE_HIGH2) {
1107                         /* this is passed to VBIOS
1108                          * to program post cursor 2 level */
1109
1110                         training_lane_set.bits.POST_CURSOR2_SET =
1111                                 link_settings->lane_settings[lane].POST_CURSOR2;
1112                 }
1113
1114                 cntl.lane_select = lane;
1115                 cntl.lane_settings = training_lane_set.raw;
1116
1117                 /* call VBIOS table to set voltage swing and pre-emphasis */
1118                 link_transmitter_control(enc110, &cntl);
1119         }
1120 }
1121
1122 /* set DP PHY test and training patterns */
1123 void dce110_link_encoder_dp_set_phy_pattern(
1124         struct link_encoder *enc,
1125         const struct encoder_set_dp_phy_pattern_param *param)
1126 {
1127         struct dce110_link_encoder *enc110 = TO_DCE110_LINK_ENC(enc);
1128
1129         switch (param->dp_phy_pattern) {
1130         case DP_TEST_PATTERN_TRAINING_PATTERN1:
1131                 dce110_link_encoder_set_dp_phy_pattern_training_pattern(enc, 0);
1132                 break;
1133         case DP_TEST_PATTERN_TRAINING_PATTERN2:
1134                 dce110_link_encoder_set_dp_phy_pattern_training_pattern(enc, 1);
1135                 break;
1136         case DP_TEST_PATTERN_TRAINING_PATTERN3:
1137                 dce110_link_encoder_set_dp_phy_pattern_training_pattern(enc, 2);
1138                 break;
1139         case DP_TEST_PATTERN_TRAINING_PATTERN4:
1140                 dce110_link_encoder_set_dp_phy_pattern_training_pattern(enc, 3);
1141                 break;
1142         case DP_TEST_PATTERN_D102:
1143                 set_dp_phy_pattern_d102(enc110);
1144                 break;
1145         case DP_TEST_PATTERN_SYMBOL_ERROR:
1146                 set_dp_phy_pattern_symbol_error(enc110);
1147                 break;
1148         case DP_TEST_PATTERN_PRBS7:
1149                 set_dp_phy_pattern_prbs7(enc110);
1150                 break;
1151         case DP_TEST_PATTERN_80BIT_CUSTOM:
1152                 set_dp_phy_pattern_80bit_custom(
1153                         enc110, param->custom_pattern);
1154                 break;
1155         case DP_TEST_PATTERN_CP2520_1:
1156                 set_dp_phy_pattern_hbr2_compliance_cp2520_2(enc110, 1);
1157                 break;
1158         case DP_TEST_PATTERN_CP2520_2:
1159                 set_dp_phy_pattern_hbr2_compliance_cp2520_2(enc110, 2);
1160                 break;
1161         case DP_TEST_PATTERN_CP2520_3:
1162                 set_dp_phy_pattern_hbr2_compliance_cp2520_2(enc110, 3);
1163                 break;
1164         case DP_TEST_PATTERN_VIDEO_MODE: {
1165                 set_dp_phy_pattern_passthrough_mode(
1166                         enc110, param->dp_panel_mode);
1167                 break;
1168         }
1169
1170         default:
1171                 /* invalid phy pattern */
1172                 ASSERT_CRITICAL(false);
1173                 break;
1174         }
1175 }
1176
1177 static void fill_stream_allocation_row_info(
1178         const struct link_mst_stream_allocation *stream_allocation,
1179         uint32_t *src,
1180         uint32_t *slots)
1181 {
1182         const struct stream_encoder *stream_enc = stream_allocation->stream_enc;
1183
1184         if (stream_enc) {
1185                 *src = stream_enc->id;
1186                 *slots = stream_allocation->slot_count;
1187         } else {
1188                 *src = 0;
1189                 *slots = 0;
1190         }
1191 }
1192
1193 /* programs DP MST VC payload allocation */
1194 void dce110_link_encoder_update_mst_stream_allocation_table(
1195         struct link_encoder *enc,
1196         const struct link_mst_stream_allocation_table *table)
1197 {
1198         struct dce110_link_encoder *enc110 = TO_DCE110_LINK_ENC(enc);
1199         uint32_t value0 = 0;
1200         uint32_t value1 = 0;
1201         uint32_t value2 = 0;
1202         uint32_t slots = 0;
1203         uint32_t src = 0;
1204         uint32_t retries = 0;
1205
1206         /* For CZ, there are only 3 pipes. So Virtual channel is up 3.*/
1207
1208         /* --- Set MSE Stream Attribute -
1209          * Setup VC Payload Table on Tx Side,
1210          * Issue allocation change trigger
1211          * to commit payload on both tx and rx side */
1212
1213         /* we should clean-up table each time */
1214
1215         if (table->stream_count >= 1) {
1216                 fill_stream_allocation_row_info(
1217                         &table->stream_allocations[0],
1218                         &src,
1219                         &slots);
1220         } else {
1221                 src = 0;
1222                 slots = 0;
1223         }
1224
1225         REG_UPDATE_2(DP_MSE_SAT0,
1226                         DP_MSE_SAT_SRC0, src,
1227                         DP_MSE_SAT_SLOT_COUNT0, slots);
1228
1229         if (table->stream_count >= 2) {
1230                 fill_stream_allocation_row_info(
1231                         &table->stream_allocations[1],
1232                         &src,
1233                         &slots);
1234         } else {
1235                 src = 0;
1236                 slots = 0;
1237         }
1238
1239         REG_UPDATE_2(DP_MSE_SAT0,
1240                         DP_MSE_SAT_SRC1, src,
1241                         DP_MSE_SAT_SLOT_COUNT1, slots);
1242
1243         if (table->stream_count >= 3) {
1244                 fill_stream_allocation_row_info(
1245                         &table->stream_allocations[2],
1246                         &src,
1247                         &slots);
1248         } else {
1249                 src = 0;
1250                 slots = 0;
1251         }
1252
1253         REG_UPDATE_2(DP_MSE_SAT1,
1254                         DP_MSE_SAT_SRC2, src,
1255                         DP_MSE_SAT_SLOT_COUNT2, slots);
1256
1257         if (table->stream_count >= 4) {
1258                 fill_stream_allocation_row_info(
1259                         &table->stream_allocations[3],
1260                         &src,
1261                         &slots);
1262         } else {
1263                 src = 0;
1264                 slots = 0;
1265         }
1266
1267         REG_UPDATE_2(DP_MSE_SAT1,
1268                         DP_MSE_SAT_SRC3, src,
1269                         DP_MSE_SAT_SLOT_COUNT3, slots);
1270
1271         /* --- wait for transaction finish */
1272
1273         /* send allocation change trigger (ACT) ?
1274          * this step first sends the ACT,
1275          * then double buffers the SAT into the hardware
1276          * making the new allocation active on the DP MST mode link */
1277
1278
1279         /* DP_MSE_SAT_UPDATE:
1280          * 0 - No Action
1281          * 1 - Update SAT with trigger
1282          * 2 - Update SAT without trigger */
1283
1284         REG_UPDATE(DP_MSE_SAT_UPDATE,
1285                         DP_MSE_SAT_UPDATE, 1);
1286
1287         /* wait for update to complete
1288          * (i.e. DP_MSE_SAT_UPDATE field is reset to 0)
1289          * then wait for the transmission
1290          * of at least 16 MTP headers on immediate local link.
1291          * i.e. DP_MSE_16_MTP_KEEPOUT field (read only) is reset to 0
1292          * a value of 1 indicates that DP MST mode
1293          * is in the 16 MTP keepout region after a VC has been added.
1294          * MST stream bandwidth (VC rate) can be configured
1295          * after this bit is cleared */
1296
1297         do {
1298                 udelay(10);
1299
1300                 value0 = REG_READ(DP_MSE_SAT_UPDATE);
1301
1302                 REG_GET(DP_MSE_SAT_UPDATE,
1303                                 DP_MSE_SAT_UPDATE, &value1);
1304
1305                 REG_GET(DP_MSE_SAT_UPDATE,
1306                                 DP_MSE_16_MTP_KEEPOUT, &value2);
1307
1308                 /* bit field DP_MSE_SAT_UPDATE is set to 1 already */
1309                 if (!value1 && !value2)
1310                         break;
1311                 ++retries;
1312         } while (retries < DP_MST_UPDATE_MAX_RETRY);
1313 }
1314
1315 void dce110_link_encoder_connect_dig_be_to_fe(
1316         struct link_encoder *enc,
1317         enum engine_id engine,
1318         bool connect)
1319 {
1320         struct dce110_link_encoder *enc110 = TO_DCE110_LINK_ENC(enc);
1321         uint32_t field;
1322
1323         if (engine != ENGINE_ID_UNKNOWN) {
1324
1325                 REG_GET(DIG_BE_CNTL, DIG_FE_SOURCE_SELECT, &field);
1326
1327                 if (connect)
1328                         field |= get_frontend_source(engine);
1329                 else
1330                         field &= ~get_frontend_source(engine);
1331
1332                 REG_UPDATE(DIG_BE_CNTL, DIG_FE_SOURCE_SELECT, field);
1333         }
1334 }
1335
1336 void dce110_link_encoder_enable_hpd(struct link_encoder *enc)
1337 {
1338         struct dce110_link_encoder *enc110 = TO_DCE110_LINK_ENC(enc);
1339         struct dc_context *ctx = enc110->base.ctx;
1340         uint32_t addr = HPD_REG(DC_HPD_CONTROL);
1341         uint32_t hpd_enable = 0;
1342         uint32_t value = dm_read_reg(ctx, addr);
1343
1344         get_reg_field_value(hpd_enable, DC_HPD_CONTROL, DC_HPD_EN);
1345
1346         if (hpd_enable == 0)
1347                 set_reg_field_value(value, 1, DC_HPD_CONTROL, DC_HPD_EN);
1348 }
1349
1350 void dce110_link_encoder_disable_hpd(struct link_encoder *enc)
1351 {
1352         struct dce110_link_encoder *enc110 = TO_DCE110_LINK_ENC(enc);
1353         struct dc_context *ctx = enc110->base.ctx;
1354         uint32_t addr = HPD_REG(DC_HPD_CONTROL);
1355         uint32_t value = dm_read_reg(ctx, addr);
1356
1357         set_reg_field_value(value, 0, DC_HPD_CONTROL, DC_HPD_EN);
1358 }