arch/arm64/boot/dts/renesas/salvator-common.dtsi

   1 // SPDX-License-Identifier: GPL-2.0
   2 /*
   3  * Device Tree Source for common parts of Salvator-X board variants
   4  *
   5  * Copyright (C) 2015-2016 Renesas Electronics Corp.
   6  */
   7
   8 /*
   9  * SSI-AK4613
  10  *
  11  * This command is required when Playback/Capture
  12  *
  13  *      amixer set "DVC Out" 100%
  14  *      amixer set "DVC In" 100%
  15  *
  16  * You can use Mute
  17  *
  18  *      amixer set "DVC Out Mute" on
  19  *      amixer set "DVC In Mute" on
  20  *
  21  * You can use Volume Ramp
  22  *
  23  *      amixer set "DVC Out Ramp Up Rate"   "0.125 dB/64 steps"
  24  *      amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
  25  *      amixer set "DVC Out Ramp" on
  26  *      aplay xxx.wav &
  27  *      amixer set "DVC Out"  80%  // Volume Down
  28  *      amixer set "DVC Out" 100%  // Volume Up
  29  */
  30
  31 #include <dt-bindings/gpio/gpio.h>
  32 #include <dt-bindings/input/input.h>
  33
  34 / {
  35         aliases {
  36                 serial0 = &scif2;
  37                 serial1 = &hscif1;
  38                 ethernet0 = &avb;
  39         };
  40
  41         chosen {
  42                 bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
  43                 stdout-path = "serial0:115200n8";
  44         };
  45
  46         audio_clkout: audio-clkout {
  47                 /*
  48                  * This is same as <&rcar_sound 0>
  49                  * but needed to avoid cs2000/rcar_sound probe dead-lock
  50                  */
  51                 compatible = "fixed-clock";
  52                 #clock-cells = <0>;
  53                 clock-frequency = <12288000>;
  54         };
  55
  56         backlight: backlight {
  57                 compatible = "pwm-backlight";
  58                 pwms = <&pwm1 0 50000>;
  59
  60                 brightness-levels = <256 128 64 16 8 4 0>;
  61                 default-brightness-level = <6>;
  62
  63                 power-supply = <&reg_12v>;
  64                 enable-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
  65         };
  66
  67         cvbs-in {
  68                 compatible = "composite-video-connector";
  69                 label = "CVBS IN";
  70
  71                 port {
  72                         cvbs_con: endpoint {
  73                                 remote-endpoint = <&adv7482_ain7>;
  74                         };
  75                 };
  76         };
  77
  78         hdmi-in {
  79                 compatible = "hdmi-connector";
  80                 label = "HDMI IN";
  81                 type = "a";
  82
  83                 port {
  84                         hdmi_in_con: endpoint {
  85                                 remote-endpoint = <&adv7482_hdmi>;
  86                         };
  87                 };
  88         };
  89
  90         hdmi0-out {
  91                 compatible = "hdmi-connector";
  92                 label = "HDMI0 OUT";
  93                 type = "a";
  94
  95                 port {
  96                         hdmi0_con: endpoint {
  97                         };
  98                 };
  99         };
 100
 101         hdmi1-out {
 102                 compatible = "hdmi-connector";
 103                 label = "HDMI1 OUT";
 104                 type = "a";
 105
 106                 port {
 107                         hdmi1_con: endpoint {
 108                         };
 109                 };
 110         };
 111
 112         keys {
 113                 compatible = "gpio-keys";
 114
 115                 pinctrl-0 = <&keys_pins>;
 116                 pinctrl-names = "default";
 117
 118                 key-1 {
 119                         gpios = <&gpio5 17 GPIO_ACTIVE_LOW>;
 120                         linux,code = <KEY_1>;
 121                         label = "SW4-1";
 122                         wakeup-source;
 123                         debounce-interval = <20>;
 124                 };
 125                 key-2 {
 126                         gpios = <&gpio5 20 GPIO_ACTIVE_LOW>;
 127                         linux,code = <KEY_2>;
 128                         label = "SW4-2";
 129                         wakeup-source;
 130                         debounce-interval = <20>;
 131                 };
 132                 key-3 {
 133                         gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
 134                         linux,code = <KEY_3>;
 135                         label = "SW4-3";
 136                         wakeup-source;
 137                         debounce-interval = <20>;
 138                 };
 139                 key-4 {
 140                         gpios = <&gpio5 23 GPIO_ACTIVE_LOW>;
 141                         linux,code = <KEY_4>;
 142                         label = "SW4-4";
 143                         wakeup-source;
 144                         debounce-interval = <20>;
 145                 };
 146                 key-a {
 147                         gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
 148                         linux,code = <KEY_A>;
 149                         label = "TSW0";
 150                         wakeup-source;
 151                         debounce-interval = <20>;
 152                 };
 153                 key-b {
 154                         gpios = <&gpio6 12 GPIO_ACTIVE_LOW>;
 155                         linux,code = <KEY_B>;
 156                         label = "TSW1";
 157                         wakeup-source;
 158                         debounce-interval = <20>;
 159                 };
 160                 key-c {
 161                         gpios = <&gpio6 13 GPIO_ACTIVE_LOW>;
 162                         linux,code = <KEY_C>;
 163                         label = "TSW2";
 164                         wakeup-source;
 165                         debounce-interval = <20>;
 166                 };
 167         };
 168
 169         reg_1p8v: regulator0 {
 170                 compatible = "regulator-fixed";
 171                 regulator-name = "fixed-1.8V";
 172                 regulator-min-microvolt = <1800000>;
 173                 regulator-max-microvolt = <1800000>;
 174                 regulator-boot-on;
 175                 regulator-always-on;
 176         };
 177
 178         reg_3p3v: regulator1 {
 179                 compatible = "regulator-fixed";
 180                 regulator-name = "fixed-3.3V";
 181                 regulator-min-microvolt = <3300000>;
 182                 regulator-max-microvolt = <3300000>;
 183                 regulator-boot-on;
 184                 regulator-always-on;
 185         };
 186
 187         reg_12v: regulator2 {
 188                 compatible = "regulator-fixed";
 189                 regulator-name = "fixed-12V";
 190                 regulator-min-microvolt = <12000000>;
 191                 regulator-max-microvolt = <12000000>;
 192                 regulator-boot-on;
 193                 regulator-always-on;
 194         };
 195
 196         sound_card: sound {
 197                 compatible = "audio-graph-card";
 198
 199                 label = "rcar-sound";
 200
 201                 dais = <&rsnd_port0>;
 202         };
 203
 204         vbus0_usb2: regulator-vbus0-usb2 {
 205                 compatible = "regulator-fixed";
 206
 207                 regulator-name = "USB20_VBUS0";
 208                 regulator-min-microvolt = <5000000>;
 209                 regulator-max-microvolt = <5000000>;
 210
 211                 gpio = <&gpio6 16 GPIO_ACTIVE_HIGH>;
 212                 enable-active-high;
 213         };
 214
 215         vcc_sdhi0: regulator-vcc-sdhi0 {
 216                 compatible = "regulator-fixed";
 217
 218                 regulator-name = "SDHI0 Vcc";
 219                 regulator-min-microvolt = <3300000>;
 220                 regulator-max-microvolt = <3300000>;
 221
 222                 gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
 223                 enable-active-high;
 224         };
 225
 226         vccq_sdhi0: regulator-vccq-sdhi0 {
 227                 compatible = "regulator-gpio";
 228
 229                 regulator-name = "SDHI0 VccQ";
 230                 regulator-min-microvolt = <1800000>;
 231                 regulator-max-microvolt = <3300000>;
 232
 233                 gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
 234                 gpios-states = <1>;
 235                 states = <3300000 1
 236                           1800000 0>;
 237         };
 238
 239         vcc_sdhi3: regulator-vcc-sdhi3 {
 240                 compatible = "regulator-fixed";
 241
 242                 regulator-name = "SDHI3 Vcc";
 243                 regulator-min-microvolt = <3300000>;
 244                 regulator-max-microvolt = <3300000>;
 245
 246                 gpio = <&gpio3 15 GPIO_ACTIVE_HIGH>;
 247                 enable-active-high;
 248         };
 249
 250         vccq_sdhi3: regulator-vccq-sdhi3 {
 251                 compatible = "regulator-gpio";
 252
 253                 regulator-name = "SDHI3 VccQ";
 254                 regulator-min-microvolt = <1800000>;
 255                 regulator-max-microvolt = <3300000>;
 256
 257                 gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
 258                 gpios-states = <1>;
 259                 states = <3300000 1
 260                           1800000 0>;
 261         };
 262
 263         vga {
 264                 compatible = "vga-connector";
 265
 266                 port {
 267                         vga_in: endpoint {
 268                                 remote-endpoint = <&adv7123_out>;
 269                         };
 270                 };
 271         };
 272
 273         vga-encoder {
 274                 compatible = "adi,adv7123";
 275
 276                 ports {
 277                         #address-cells = <1>;
 278                         #size-cells = <0>;
 279
 280                         port@0 {
 281                                 reg = <0>;
 282                                 adv7123_in: endpoint {
 283                                         remote-endpoint = <&du_out_rgb>;
 284                                 };
 285                         };
 286                         port@1 {
 287                                 reg = <1>;
 288                                 adv7123_out: endpoint {
 289                                         remote-endpoint = <&vga_in>;
 290                                 };
 291                         };
 292                 };
 293         };
 294
 295         x12_clk: x12 {
 296                 compatible = "fixed-clock";
 297                 #clock-cells = <0>;
 298                 clock-frequency = <24576000>;
 299         };
 300
 301         /* External DU dot clocks */
 302         x21_clk: x21-clock {
 303                 compatible = "fixed-clock";
 304                 #clock-cells = <0>;
 305                 clock-frequency = <33000000>;
 306         };
 307
 308         x22_clk: x22-clock {
 309                 compatible = "fixed-clock";
 310                 #clock-cells = <0>;
 311                 clock-frequency = <33000000>;
 312         };
 313
 314         x23_clk: x23-clock {
 315                 compatible = "fixed-clock";
 316                 #clock-cells = <0>;
 317                 clock-frequency = <25000000>;
 318         };
 319 };
 320
 321 &audio_clk_a {
 322         clock-frequency = <22579200>;
 323 };
 324
 325 &avb {
 326         pinctrl-0 = <&avb_pins>;
 327         pinctrl-names = "default";
 328         phy-handle = <&phy0>;
 329         phy-mode = "rgmii-txid";
 330         status = "okay";
 331
 332         phy0: ethernet-phy@0 {
 333                 rxc-skew-ps = <1500>;
 334                 reg = <0>;
 335                 interrupt-parent = <&gpio2>;
 336                 interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
 337                 reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
 338         };
 339 };
 340
 341 &csi20 {
 342         status = "okay";
 343
 344         ports {
 345                 port@0 {
 346                         reg = <0>;
 347                         csi20_in: endpoint {
 348                                 clock-lanes = <0>;
 349                                 data-lanes = <1>;
 350                                 remote-endpoint = <&adv7482_txb>;
 351                         };
 352                 };
 353         };
 354 };
 355
 356 &csi40 {
 357         status = "okay";
 358
 359         ports {
 360                 port@0 {
 361                         reg = <0>;
 362
 363                         csi40_in: endpoint {
 364                                 clock-lanes = <0>;
 365                                 data-lanes = <1 2 3 4>;
 366                                 remote-endpoint = <&adv7482_txa>;
 367                         };
 368                 };
 369         };
 370 };
 371
 372 &du {
 373         pinctrl-0 = <&du_pins>;
 374         pinctrl-names = "default";
 375         status = "okay";
 376
 377         ports {
 378                 port@0 {
 379                         endpoint {
 380                                 remote-endpoint = <&adv7123_in>;
 381                         };
 382                 };
 383         };
 384 };
 385
 386 &ehci0 {
 387         dr_mode = "otg";
 388         status = "okay";
 389 };
 390
 391 &ehci1 {
 392         status = "okay";
 393 };
 394
 395 &extalr_clk {
 396         clock-frequency = <32768>;
 397 };
 398
 399 &hscif1 {
 400         pinctrl-0 = <&hscif1_pins>;
 401         pinctrl-names = "default";
 402
 403         uart-has-rtscts;
 404         /* Please only enable hscif1 or scif1 */
 405         status = "okay";
 406 };
 407
 408 &hsusb {
 409         dr_mode = "otg";
 410         status = "okay";
 411 };
 412
 413 &i2c2 {
 414         pinctrl-0 = <&i2c2_pins>;
 415         pinctrl-names = "default";
 416
 417         status = "okay";
 418
 419         clock-frequency = <100000>;
 420
 421         ak4613: codec@10 {
 422                 compatible = "asahi-kasei,ak4613";
 423                 #sound-dai-cells = <0>;
 424                 reg = <0x10>;
 425                 clocks = <&rcar_sound 3>;
 426
 427                 asahi-kasei,in1-single-end;
 428                 asahi-kasei,in2-single-end;
 429                 asahi-kasei,out1-single-end;
 430                 asahi-kasei,out2-single-end;
 431                 asahi-kasei,out3-single-end;
 432                 asahi-kasei,out4-single-end;
 433                 asahi-kasei,out5-single-end;
 434                 asahi-kasei,out6-single-end;
 435
 436                 port {
 437                         ak4613_endpoint: endpoint {
 438                                 remote-endpoint = <&rsnd_endpoint0>;
 439                         };
 440                 };
 441         };
 442
 443         cs2000: clk_multiplier@4f {
 444                 #clock-cells = <0>;
 445                 compatible = "cirrus,cs2000-cp";
 446                 reg = <0x4f>;
 447                 clocks = <&audio_clkout>, <&x12_clk>;
 448                 clock-names = "clk_in", "ref_clk";
 449
 450                 assigned-clocks = <&cs2000>;
 451                 assigned-clock-rates = <24576000>; /* 1/1 divide */
 452         };
 453 };
 454
 455 &i2c4 {
 456         status = "okay";
 457
 458         pca9654: gpio@20 {
 459                 compatible = "onnn,pca9654";
 460                 reg = <0x20>;
 461                 gpio-controller;
 462                 #gpio-cells = <2>;
 463         };
 464
 465         video-receiver@70 {
 466                 compatible = "adi,adv7482";
 467                 reg = <0x70 0x71 0x72 0x73 0x74 0x75
 468                        0x60 0x61 0x62 0x63 0x64 0x65>;
 469                 reg-names = "main", "dpll", "cp", "hdmi", "edid", "repeater",
 470                             "infoframe", "cbus", "cec", "sdp", "txa", "txb" ;
 471
 472                 #address-cells = <1>;
 473                 #size-cells = <0>;
 474
 475                 interrupt-parent = <&gpio6>;
 476                 interrupt-names = "intrq1", "intrq2";
 477                 interrupts = <30 IRQ_TYPE_LEVEL_LOW>,
 478                              <31 IRQ_TYPE_LEVEL_LOW>;
 479
 480                 port@7 {
 481                         reg = <7>;
 482
 483                         adv7482_ain7: endpoint {
 484                                 remote-endpoint = <&cvbs_con>;
 485                         };
 486                 };
 487
 488                 port@8 {
 489                         reg = <8>;
 490
 491                         adv7482_hdmi: endpoint {
 492                                 remote-endpoint = <&hdmi_in_con>;
 493                         };
 494                 };
 495
 496                 port@a {
 497                         reg = <10>;
 498
 499                         adv7482_txa: endpoint {
 500                                 clock-lanes = <0>;
 501                                 data-lanes = <1 2 3 4>;
 502                                 remote-endpoint = <&csi40_in>;
 503                         };
 504                 };
 505
 506                 port@b {
 507                         reg = <11>;
 508
 509                         adv7482_txb: endpoint {
 510                                 clock-lanes = <0>;
 511                                 data-lanes = <1>;
 512                                 remote-endpoint = <&csi20_in>;
 513                         };
 514                 };
 515         };
 516
 517         csa_vdd: adc@7c {
 518                 compatible = "maxim,max9611";
 519                 reg = <0x7c>;
 520
 521                 shunt-resistor-micro-ohms = <5000>;
 522         };
 523
 524         csa_dvfs: adc@7f {
 525                 compatible = "maxim,max9611";
 526                 reg = <0x7f>;
 527
 528                 shunt-resistor-micro-ohms = <5000>;
 529         };
 530 };
 531
 532 &i2c_dvfs {
 533         status = "okay";
 534
 535         clock-frequency = <400000>;
 536
 537         pmic: pmic@30 {
 538                 pinctrl-0 = <&irq0_pins>;
 539                 pinctrl-names = "default";
 540
 541                 compatible = "rohm,bd9571mwv";
 542                 reg = <0x30>;
 543                 interrupt-parent = <&intc_ex>;
 544                 interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
 545                 interrupt-controller;
 546                 #interrupt-cells = <2>;
 547                 gpio-controller;
 548                 #gpio-cells = <2>;
 549                 rohm,ddr-backup-power = <0xf>;
 550                 rohm,rstbmode-level;
 551
 552                 regulators {
 553                         dvfs: dvfs {
 554                                 regulator-name = "dvfs";
 555                                 regulator-min-microvolt = <750000>;
 556                                 regulator-max-microvolt = <1030000>;
 557                                 regulator-boot-on;
 558                                 regulator-always-on;
 559                         };
 560                 };
 561         };
 562
 563         eeprom@50 {
 564                 compatible = "rohm,br24t01", "atmel,24c01";
 565                 reg = <0x50>;
 566                 pagesize = <8>;
 567         };
 568 };
 569
 570 &ohci0 {
 571         dr_mode = "otg";
 572         status = "okay";
 573 };
 574
 575 &ohci1 {
 576         status = "okay";
 577 };
 578
 579 &pcie_bus_clk {
 580         clock-frequency = <100000000>;
 581 };
 582
 583 &pciec0 {
 584         status = "okay";
 585 };
 586
 587 &pciec1 {
 588         status = "okay";
 589 };
 590
 591 &pfc {
 592         pinctrl-0 = <&scif_clk_pins>;
 593         pinctrl-names = "default";
 594
 595         avb_pins: avb {
 596                 mux {
 597                         groups = "avb_link", "avb_mdio", "avb_mii";
 598                         function = "avb";
 599                 };
 600
 601                 pins_mdio {
 602                         groups = "avb_mdio";
 603                         drive-strength = <24>;
 604                 };
 605
 606                 pins_mii_tx {
 607                         pins = "PIN_AVB_TX_CTL", "PIN_AVB_TXC", "PIN_AVB_TD0",
 608                                "PIN_AVB_TD1", "PIN_AVB_TD2", "PIN_AVB_TD3";
 609                         drive-strength = <12>;
 610                 };
 611         };
 612
 613         du_pins: du {
 614                 groups = "du_rgb888", "du_sync", "du_oddf", "du_clk_out_0";
 615                 function = "du";
 616         };
 617
 618         hscif1_pins: hscif1 {
 619                 groups = "hscif1_data_a", "hscif1_ctrl_a";
 620                 function = "hscif1";
 621         };
 622
 623         i2c2_pins: i2c2 {
 624                 groups = "i2c2_a";
 625                 function = "i2c2";
 626         };
 627
 628         irq0_pins: irq0 {
 629                 groups = "intc_ex_irq0";
 630                 function = "intc_ex";
 631         };
 632
 633         keys_pins: keys {
 634                 pins = "GP_5_17", "GP_5_20", "GP_5_22";
 635                 bias-pull-up;
 636         };
 637
 638         pwm1_pins: pwm1 {
 639                 groups = "pwm1_a";
 640                 function = "pwm1";
 641         };
 642
 643         scif1_pins: scif1 {
 644                 groups = "scif1_data_a", "scif1_ctrl";
 645                 function = "scif1";
 646         };
 647
 648         scif2_pins: scif2 {
 649                 groups = "scif2_data_a";
 650                 function = "scif2";
 651         };
 652
 653         scif_clk_pins: scif_clk {
 654                 groups = "scif_clk_a";
 655                 function = "scif_clk";
 656         };
 657
 658         sdhi0_pins: sd0 {
 659                 groups = "sdhi0_data4", "sdhi0_ctrl";
 660                 function = "sdhi0";
 661                 power-source = <3300>;
 662         };
 663
 664         sdhi0_pins_uhs: sd0_uhs {
 665                 groups = "sdhi0_data4", "sdhi0_ctrl";
 666                 function = "sdhi0";
 667                 power-source = <1800>;
 668         };
 669
 670         sdhi2_pins: sd2 {
 671                 groups = "sdhi2_data8", "sdhi2_ctrl", "sdhi2_ds";
 672                 function = "sdhi2";
 673                 power-source = <1800>;
 674         };
 675
 676         sdhi3_pins: sd3 {
 677                 groups = "sdhi3_data4", "sdhi3_ctrl";
 678                 function = "sdhi3";
 679                 power-source = <3300>;
 680         };
 681
 682         sdhi3_pins_uhs: sd3_uhs {
 683                 groups = "sdhi3_data4", "sdhi3_ctrl";
 684                 function = "sdhi3";
 685                 power-source = <1800>;
 686         };
 687
 688         sound_pins: sound {
 689                 groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a";
 690                 function = "ssi";
 691         };
 692
 693         sound_clk_pins: sound_clk {
 694                 groups = "audio_clk_a_a", "audio_clk_b_a", "audio_clk_c_a",
 695                          "audio_clkout_a", "audio_clkout3_a";
 696                 function = "audio_clk";
 697         };
 698
 699         usb0_pins: usb0 {
 700                 groups = "usb0";
 701                 function = "usb0";
 702         };
 703
 704         usb1_pins: usb1 {
 705                 mux {
 706                         groups = "usb1";
 707                         function = "usb1";
 708                 };
 709
 710                 ovc {
 711                         pins = "GP_6_27";
 712                         bias-pull-up;
 713                 };
 714
 715                 pwen {
 716                         pins = "GP_6_26";
 717                         bias-pull-down;
 718                 };
 719         };
 720
 721         usb30_pins: usb30 {
 722                 groups = "usb30";
 723                 function = "usb30";
 724         };
 725 };
 726
 727 &pwm1 {
 728         pinctrl-0 = <&pwm1_pins>;
 729         pinctrl-names = "default";
 730
 731         status = "okay";
 732 };
 733
 734 &rcar_sound {
 735         pinctrl-0 = <&sound_pins &sound_clk_pins>;
 736         pinctrl-names = "default";
 737
 738         /* Single DAI */
 739         #sound-dai-cells = <0>;
 740
 741         /* audio_clkout0/1/2/3 */
 742         #clock-cells = <1>;
 743         clock-frequency = <12288000 11289600>;
 744
 745         status = "okay";
 746
 747         /* update <audio_clk_b> to <cs2000> */
 748         clocks = <&cpg CPG_MOD 1005>,
 749                  <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>,
 750                  <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>,
 751                  <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>,
 752                  <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>,
 753                  <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>,
 754                  <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>,
 755                  <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>,
 756                  <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>,
 757                  <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>,
 758                  <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>,
 759                  <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
 760                  <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
 761                  <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
 762                  <&audio_clk_a>, <&cs2000>,
 763                  <&audio_clk_c>,
 764                  <&cpg CPG_CORE CPG_AUDIO_CLK_I>;
 765
 766         ports {
 767                 #address-cells = <1>;
 768                 #size-cells = <0>;
 769                 rsnd_port0: port@0 {
 770                         reg = <0>;
 771                         rsnd_endpoint0: endpoint {
 772                                 remote-endpoint = <&ak4613_endpoint>;
 773
 774                                 dai-format = "left_j";
 775                                 bitclock-master = <&rsnd_endpoint0>;
 776                                 frame-master = <&rsnd_endpoint0>;
 777
 778                                 playback = <&ssi0 &src0 &dvc0>;
 779                                 capture  = <&ssi1 &src1 &dvc1>;
 780                         };
 781                 };
 782         };
 783 };
 784
 785 &rwdt {
 786         timeout-sec = <60>;
 787         status = "okay";
 788 };
 789
 790 &scif1 {
 791         pinctrl-0 = <&scif1_pins>;
 792         pinctrl-names = "default";
 793
 794         uart-has-rtscts;
 795         /* Please only enable hscif1 or scif1 */
 796         /* status = "okay"; */
 797 };
 798
 799 &scif2 {
 800         pinctrl-0 = <&scif2_pins>;
 801         pinctrl-names = "default";
 802
 803         status = "okay";
 804 };
 805
 806 &scif_clk {
 807         clock-frequency = <14745600>;
 808 };
 809
 810 &sdhi0 {
 811         pinctrl-0 = <&sdhi0_pins>;
 812         pinctrl-1 = <&sdhi0_pins_uhs>;
 813         pinctrl-names = "default", "state_uhs";
 814
 815         vmmc-supply = <&vcc_sdhi0>;
 816         vqmmc-supply = <&vccq_sdhi0>;
 817         cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
 818         wp-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
 819         bus-width = <4>;
 820         sd-uhs-sdr50;
 821         sd-uhs-sdr104;
 822         status = "okay";
 823 };
 824
 825 &sdhi2 {
 826         /* used for on-board 8bit eMMC */
 827         pinctrl-0 = <&sdhi2_pins>;
 828         pinctrl-1 = <&sdhi2_pins>;
 829         pinctrl-names = "default", "state_uhs";
 830
 831         vmmc-supply = <&reg_3p3v>;
 832         vqmmc-supply = <&reg_1p8v>;
 833         bus-width = <8>;
 834         mmc-hs200-1_8v;
 835         mmc-hs400-1_8v;
 836         non-removable;
 837         fixed-emmc-driver-type = <1>;
 838         status = "okay";
 839 };
 840
 841 &sdhi3 {
 842         pinctrl-0 = <&sdhi3_pins>;
 843         pinctrl-1 = <&sdhi3_pins_uhs>;
 844         pinctrl-names = "default", "state_uhs";
 845
 846         vmmc-supply = <&vcc_sdhi3>;
 847         vqmmc-supply = <&vccq_sdhi3>;
 848         cd-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
 849         wp-gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
 850         bus-width = <4>;
 851         sd-uhs-sdr50;
 852         sd-uhs-sdr104;
 853         status = "okay";
 854 };
 855
 856 &ssi1 {
 857         shared-pin;
 858 };
 859
 860 &usb_extal_clk {
 861         clock-frequency = <50000000>;
 862 };
 863
 864 &usb2_phy0 {
 865         pinctrl-0 = <&usb0_pins>;
 866         pinctrl-names = "default";
 867
 868         vbus-supply = <&vbus0_usb2>;
 869         status = "okay";
 870 };
 871
 872 &usb2_phy1 {
 873         pinctrl-0 = <&usb1_pins>;
 874         pinctrl-names = "default";
 875
 876         status = "okay";
 877 };
 878
 879 &usb3_peri0 {
 880         phys = <&usb3_phy0>;
 881         phy-names = "usb";
 882
 883         companion = <&xhci0>;
 884
 885         status = "okay";
 886 };
 887
 888 &usb3_phy0 {
 889         status = "okay";
 890 };
 891
 892 &usb3s0_clk {
 893         clock-frequency = <100000000>;
 894 };
 895
 896 &vin0 {
 897         status = "okay";
 898 };
 899
 900 &vin1 {
 901         status = "okay";
 902 };
 903
 904 &vin2 {
 905         status = "okay";
 906 };
 907
 908 &vin3 {
 909         status = "okay";
 910 };
 911
 912 &vin4 {
 913         status = "okay";
 914 };
 915
 916 &vin5 {
 917         status = "okay";
 918 };
 919
 920 &vin6 {
 921         status = "okay";
 922 };
 923
 924 &vin7 {
 925         status = "okay";
 926 };
 927
 928 &xhci0 {
 929         pinctrl-0 = <&usb30_pins>;
 930         pinctrl-names = "default";
 931
 932         status = "okay";
 933 };