arch/arm/boot/dts/qcom-apq8064-ifc6410.dts

   1 // SPDX-License-Identifier: GPL-2.0
   2 #include "qcom-apq8064-v2.0.dtsi"
   3 #include <dt-bindings/gpio/gpio.h>
   4 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
   5
   6 / {
   7         model = "Qualcomm APQ8064/IFC6410";
   8         compatible = "qcom,apq8064-ifc6410", "qcom,apq8064";
   9
  10         aliases {
  11                 serial0 = &gsbi7_serial;
  12                 serial1 = &gsbi6_serial;
  13                 i2c0 = &gsbi1_i2c;
  14                 i2c1 = &gsbi2_i2c;
  15                 i2c2 = &gsbi3_i2c;
  16                 i2c3 = &gsbi4_i2c;
  17                 spi0 = &gsbi5_spi;
  18         };
  19
  20         chosen {
  21                 stdout-path = "serial0:115200n8";
  22         };
  23
  24         pwrseq {
  25                 compatible = "simple-bus";
  26
  27                 sdcc4_pwrseq: sdcc4_pwrseq {
  28                         pinctrl-names = "default";
  29                         pinctrl-0 = <&wlan_default_gpios>;
  30                         compatible = "mmc-pwrseq-simple";
  31                         reset-gpios = <&pm8921_gpio 43 GPIO_ACTIVE_LOW>;
  32                 };
  33         };
  34
  35         leds {
  36                 compatible = "gpio-leds";
  37                 pinctrl-names = "default";
  38                 pinctrl-0 = <&notify_led>;
  39
  40                 led@1 {
  41                         label = "apq8064:green:user1";
  42                         gpios = <&pm8921_gpio 18 GPIO_ACTIVE_HIGH>;
  43                         default-state = "on";
  44                 };
  45         };
  46
  47         hdmi-out {
  48                 compatible = "hdmi-connector";
  49                 type = "d";
  50
  51                 port {
  52                         hdmi_con: endpoint {
  53                                 remote-endpoint = <&hdmi_out>;
  54                         };
  55                 };
  56         };
  57
  58         soc {
  59                 pinctrl@800000 {
  60                         card_detect: card_detect {
  61                                 mux {
  62                                         pins = "gpio26";
  63                                         function = "gpio";
  64                                         bias-disable;
  65                                 };
  66                         };
  67
  68                         pcie_pins: pcie_pinmux {
  69                                 mux {
  70                                         pins = "gpio27";
  71                                         function = "gpio";
  72                                 };
  73                                 conf {
  74                                         pins = "gpio27";
  75                                         drive-strength = <12>;
  76                                         bias-disable;
  77                                 };
  78                         };
  79                 };
  80
  81                 rpm@108000 {
  82                         regulators {
  83                                 vin_lvs1_3_6-supply = <&pm8921_s4>;
  84                                 vin_lvs2-supply = <&pm8921_s1>;
  85                                 vin_lvs4_5_7-supply = <&pm8921_s4>;
  86
  87                                 vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
  88                                 vdd_l24-supply = <&pm8921_s1>;
  89                                 vdd_l25-supply = <&pm8921_s1>;
  90                                 vdd_l26-supply = <&pm8921_s7>;
  91                                 vdd_l27-supply = <&pm8921_s7>;
  92                                 vdd_l28-supply = <&pm8921_s7>;
  93
  94
  95                                 /* Buck SMPS */
  96                                 s1 {
  97                                         regulator-always-on;
  98                                         regulator-min-microvolt = <1225000>;
  99                                         regulator-max-microvolt = <1225000>;
 100                                         qcom,switch-mode-frequency = <3200000>;
 101                                         bias-pull-down;
 102                                 };
 103
 104                                 s3 {
 105                                         regulator-min-microvolt = <1000000>;
 106                                         regulator-max-microvolt = <1400000>;
 107                                         qcom,switch-mode-frequency = <4800000>;
 108                                 };
 109
 110                                 s4 {
 111                                         regulator-min-microvolt = <1800000>;
 112                                         regulator-max-microvolt = <1800000>;
 113                                         qcom,switch-mode-frequency = <3200000>;
 114                                 };
 115
 116                                 s7 {
 117                                         regulator-min-microvolt = <1300000>;
 118                                         regulator-max-microvolt = <1300000>;
 119                                         qcom,switch-mode-frequency = <3200000>;
 120                                 };
 121
 122                                 l3 {
 123                                         regulator-min-microvolt = <3050000>;
 124                                         regulator-max-microvolt = <3300000>;
 125                                         bias-pull-down;
 126                                 };
 127
 128                                 l4 {
 129                                         regulator-min-microvolt = <1000000>;
 130                                         regulator-max-microvolt = <1800000>;
 131                                         bias-pull-down;
 132                                 };
 133
 134                                 l5 {
 135                                         regulator-min-microvolt = <2750000>;
 136                                         regulator-max-microvolt = <3000000>;
 137                                         bias-pull-down;
 138                                 };
 139
 140                                 l6 {
 141                                         regulator-min-microvolt = <2950000>;
 142                                         regulator-max-microvolt = <2950000>;
 143                                         bias-pull-down;
 144                                 };
 145
 146                                 l23 {
 147                                         regulator-min-microvolt = <1700000>;
 148                                         regulator-max-microvolt = <1900000>;
 149                                         bias-pull-down;
 150                                 };
 151
 152                                 lvs1 {
 153                                         bias-pull-down;
 154                                 };
 155
 156                                 lvs6 {
 157                                         bias-pull-down;
 158                                 };
 159                         };
 160                 };
 161
 162                 ext_3p3v: regulator-fixed@1 {
 163                         compatible = "regulator-fixed";
 164                         regulator-min-microvolt = <3300000>;
 165                         regulator-max-microvolt = <3300000>;
 166                         regulator-name = "ext_3p3v";
 167                         regulator-type = "voltage";
 168                         startup-delay-us = <0>;
 169                         gpio = <&tlmm_pinmux 77 GPIO_ACTIVE_HIGH>;
 170                         enable-active-high;
 171                         regulator-boot-on;
 172                 };
 173
 174                 gsbi3: gsbi@16200000 {
 175                         status = "okay";
 176                         qcom,mode = <GSBI_PROT_I2C>;
 177                         i2c@16280000 {
 178                                 status = "okay";
 179                         };
 180                 };
 181
 182                 gsbi@16300000 {
 183                         status = "okay";
 184                         qcom,mode = <GSBI_PROT_I2C>;
 185                         /* CAM I2C MIPI-CSI connector */
 186                         i2c@16380000 {
 187                                 status = "okay";
 188                         };
 189                 };
 190
 191                 gsbi@12440000 {
 192                         status = "okay";
 193                         qcom,mode = <GSBI_PROT_I2C>;
 194
 195                         i2c@12460000 {
 196                                 status = "okay";
 197                                 clock-frequency = <200000>;
 198
 199                                 eeprom@52 {
 200                                         compatible = "atmel,24c128";
 201                                         reg = <0x52>;
 202                                         pagesize = <32>;
 203                                 };
 204                         };
 205                 };
 206
 207                 gsbi@1a200000 {
 208                         qcom,mode = <GSBI_PROT_SPI>;
 209                         status = "okay";
 210                         spi4: spi@1a280000 {
 211                                 status = "okay";
 212                                 num-cs = <1>;
 213                                 cs-gpios = <&tlmm_pinmux 53 0>;
 214                         };
 215                 };
 216
 217                 gsbi@16500000 {
 218                         status = "ok";
 219                         qcom,mode = <GSBI_PROT_UART_W_FC>;
 220
 221                         serial@16540000 {
 222                                 status = "ok";
 223                                 pinctrl-names = "default";
 224                                 pinctrl-0 = <&gsbi6_uart_4pins>;
 225                         };
 226                 };
 227
 228                 gsbi@16600000 {
 229                         status = "ok";
 230                         qcom,mode = <GSBI_PROT_I2C_UART>;
 231                         serial@16640000 {
 232                                 status = "ok";
 233                                 pinctrl-names = "default";
 234                                 pinctrl-0 = <&gsbi7_uart_2pins>;
 235                         };
 236                 };
 237
 238                 sata_phy0: phy@1b400000 {
 239                         status = "okay";
 240                 };
 241
 242                 sata0: sata@29000000 {
 243                         status          = "okay";
 244                         target-supply   = <&pm8921_s4>;
 245                 };
 246
 247                 /* OTG */
 248                 usb@12500000 {
 249                         status = "okay";
 250                         dr_mode = "otg";
 251                         ulpi {
 252                                 phy {
 253                                         v3p3-supply = <&pm8921_l3>;
 254                                         v1p8-supply = <&pm8921_l4>;
 255                                 };
 256                         };
 257                 };
 258
 259                 usb@12520000 {
 260                         status = "okay";
 261                         dr_mode = "host";
 262                         ulpi {
 263                                 phy {
 264                                         v3p3-supply = <&pm8921_l3>;
 265                                         v1p8-supply = <&pm8921_l23>;
 266                                 };
 267                         };
 268                 };
 269
 270                 usb@12530000 {
 271                         status = "okay";
 272                         dr_mode = "host";
 273                         ulpi {
 274                                 phy {
 275                                         v3p3-supply = <&pm8921_l3>;
 276                                         v1p8-supply = <&pm8921_l23>;
 277                                 };
 278                         };
 279                 };
 280
 281                 pci@1b500000 {
 282                         status = "ok";
 283                         vdda-supply = <&pm8921_s3>;
 284                         vdda_phy-supply = <&pm8921_lvs6>;
 285                         vdda_refclk-supply = <&ext_3p3v>;
 286                         pinctrl-0 = <&pcie_pins>;
 287                         pinctrl-names = "default";
 288                         perst-gpio = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
 289                 };
 290
 291                 qcom,ssbi@500000 {
 292                         pmic@0 {
 293                                 gpio@150 {
 294                                         wlan_default_gpios: wlan-gpios {
 295                                                 pios {
 296                                                         pins = "gpio43";
 297                                                         function = "normal";
 298                                                         bias-disable;
 299                                                         power-source = <PM8921_GPIO_S4>;
 300                                                 };
 301                                         };
 302
 303                                         notify_led: nled {
 304                                                 pios {
 305                                                         pins = "gpio18";
 306                                                         function = "normal";
 307                                                         bias-disable;
 308                                                         power-source = <PM8921_GPIO_S4>;
 309                                                 };
 310                                         };
 311                                 };
 312                         };
 313                 };
 314
 315                 amba {
 316                         /* eMMC */
 317                         sdcc1: sdcc@12400000 {
 318                                 status = "okay";
 319                                 vmmc-supply = <&pm8921_l5>;
 320                                 vqmmc-supply = <&pm8921_s4>;
 321                         };
 322
 323                         /* External micro SD card */
 324                         sdcc3: sdcc@12180000 {
 325                                 status = "okay";
 326                                 vmmc-supply = <&pm8921_l6>;
 327                                 pinctrl-names   = "default";
 328                                 pinctrl-0       = <&card_detect>;
 329                                 cd-gpios        = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
 330                         };
 331                         /* WLAN */
 332                         sdcc4: sdcc@121c0000 {
 333                                 status = "okay";
 334                                 vmmc-supply = <&ext_3p3v>;
 335                                 vqmmc-supply = <&pm8921_lvs1>;
 336                                 mmc-pwrseq = <&sdcc4_pwrseq>;
 337                         };
 338                 };
 339
 340                 hdmi-tx@4a00000 {
 341                         status = "okay";
 342
 343                         core-vdda-supply = <&pm8921_hdmi_switch>;
 344                         hdmi-mux-supply = <&ext_3p3v>;
 345
 346                         hpd-gpios = <&tlmm_pinmux 72 GPIO_ACTIVE_HIGH>;
 347
 348                         ports {
 349                                 port@0 {
 350                                         endpoint {
 351                                                 remote-endpoint = <&mdp_dtv_out>;
 352                                         };
 353                                 };
 354
 355                                 port@1 {
 356                                         endpoint {
 357                                                 remote-endpoint = <&hdmi_con>;
 358                                         };
 359                                 };
 360                         };
 361                 };
 362
 363                 hdmi-phy@4a00400 {
 364                         status = "okay";
 365
 366                         core-vdda-supply = <&pm8921_hdmi_switch>;
 367                 };
 368
 369                 mdp@5100000 {
 370                         status = "okay";
 371
 372                         ports {
 373                                 port@3 {
 374                                         endpoint {
 375                                                 remote-endpoint = <&hdmi_in>;
 376                                         };
 377                                 };
 378                         };
 379                 };
 380         };
 381 };