arch/arm/boot/dts/omap5-cm-t54.dts

   1 // SPDX-License-Identifier: GPL-2.0
   2 /*
   3  * Support for CompuLab CM-T54
   4  */
   5 /dts-v1/;
   6
   7 #include "omap5.dtsi"
   8 #include <dt-bindings/interrupt-controller/irq.h>
   9 #include <dt-bindings/interrupt-controller/arm-gic.h>
  10
  11 / {
  12         model = "CompuLab CM-T54";
  13         compatible = "compulab,omap5-cm-t54", "ti,omap5";
  14
  15         memory@80000000 {
  16                 device_type = "memory";
  17                 reg = <0 0x80000000 0 0x7f000000>; /* 2048 MB */
  18         };
  19
  20         aliases {
  21                 display0 = &hdmi0;
  22                 display1 = &dvi0;
  23                 display2 = &lcd0;
  24         };
  25
  26         vmmcsd_fixed: fixed-regulator-mmcsd {
  27                 compatible = "regulator-fixed";
  28                 regulator-name = "vmmcsd_fixed";
  29                 regulator-min-microvolt = <3300000>;
  30                 regulator-max-microvolt = <3300000>;
  31         };
  32
  33         vwlan_pdn_fixed: fixed-regulator-vwlan-pdn {
  34                 compatible = "regulator-fixed";
  35                 regulator-name = "vwlan_pdn_fixed";
  36                 regulator-min-microvolt = <3300000>;
  37                 regulator-max-microvolt = <3300000>;
  38                 vin-supply = <&ldo2_reg>;
  39                 gpio = <&gpio4 13 GPIO_ACTIVE_HIGH>;   /* gpio4_109 */
  40                 startup-delay-us = <1000>;
  41                 enable-active-high;
  42         };
  43
  44         vwlan_fixed: fixed-regulator-vwlan {
  45                 compatible = "regulator-fixed";
  46                 regulator-name = "vwlan_fixed";
  47                 regulator-min-microvolt = <3300000>;
  48                 regulator-max-microvolt = <3300000>;
  49                 vin-supply = <&vwlan_pdn_fixed>;
  50                 gpio = <&gpio4 14 GPIO_ACTIVE_HIGH>;   /* gpio4_110 */
  51                 startup-delay-us = <1000>;
  52                 enable-active-high;
  53         };
  54
  55         ads7846reg: ads7846-reg {
  56                 compatible = "regulator-fixed";
  57                 regulator-name = "ads7846-reg";
  58                 regulator-min-microvolt = <3300000>;
  59                 regulator-max-microvolt = <3300000>;
  60         };
  61
  62         /* HS USB Host PHY on PORT 2 */
  63         hsusb2_phy: hsusb2_phy {
  64                 compatible = "usb-nop-xceiv";
  65                 reset-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>; /* gpio3_76 HUB_RESET */
  66                 #phy-cells = <0>;
  67         };
  68
  69         /* HS USB Host PHY on PORT 3 */
  70         hsusb3_phy: hsusb3_phy {
  71                 compatible = "usb-nop-xceiv";
  72                 reset-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>; /* gpio3_83 ETH_RESET */
  73                 #phy-cells = <0>;
  74         };
  75
  76         leds {
  77                 compatible = "gpio-leds";
  78                 led1 {
  79                         label = "Heartbeat";
  80                         gpios = <&gpio3 16 GPIO_ACTIVE_HIGH>; /* gpio3_80 ACT_LED */
  81                         linux,default-trigger = "heartbeat";
  82                         default-state = "off";
  83                 };
  84         };
  85
  86         lcd0: display {
  87                 compatible = "startek,startek-kd050c", "panel-dpi";
  88                 label = "lcd";
  89
  90                 pinctrl-names = "default";
  91                 pinctrl-0 = <&lcd_pins>;
  92
  93                 enable-gpios = <&gpio8 3 GPIO_ACTIVE_HIGH>;
  94
  95                 panel-timing {
  96                         clock-frequency = <33000000>;
  97                         hactive = <800>;
  98                         vactive = <480>;
  99                         hfront-porch = <40>;
 100                         hback-porch = <40>;
 101                         hsync-len = <43>;
 102                         vback-porch = <29>;
 103                         vfront-porch = <13>;
 104                         vsync-len = <3>;
 105                         hsync-active = <0>;
 106                         vsync-active = <0>;
 107                         de-active = <1>;
 108                         pixelclk-active = <1>;
 109                 };
 110
 111                 port {
 112                         lcd_in: endpoint {
 113                                 remote-endpoint = <&dpi_lcd_out>;
 114                         };
 115                 };
 116         };
 117
 118         hdmi0: connector0 {
 119                 compatible = "hdmi-connector";
 120                 label = "hdmi";
 121
 122                 type = "a";
 123
 124                 pinctrl-names = "default";
 125                 pinctrl-0 = <&hdmi_conn_pins>;
 126
 127                 hpd-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>; /* GPIO 193, HPD */
 128
 129                 port {
 130                         hdmi_connector_in: endpoint {
 131                                 remote-endpoint = <&hdmi_out>;
 132                         };
 133                 };
 134         };
 135
 136         tfp410: encoder0 {
 137                 compatible = "ti,tfp410";
 138
 139                 ports {
 140                         #address-cells = <1>;
 141                         #size-cells = <0>;
 142
 143                         port@0 {
 144                                 reg = <0>;
 145
 146                                 tfp410_in: endpoint {
 147                                         remote-endpoint = <&dpi_dvi_out>;
 148                                 };
 149                         };
 150
 151                         port@1 {
 152                                 reg = <1>;
 153
 154                                 tfp410_out: endpoint {
 155                                         remote-endpoint = <&dvi_connector_in>;
 156                                 };
 157                         };
 158                 };
 159         };
 160
 161         dvi0: connector1 {
 162                 compatible = "dvi-connector";
 163                 label = "dvi";
 164
 165                 digital;
 166
 167                 ddc-i2c-bus = <&i2c2>;
 168
 169                 port {
 170                         dvi_connector_in: endpoint {
 171                                 remote-endpoint = <&tfp410_out>;
 172                         };
 173                 };
 174         };
 175 };
 176
 177 &omap5_pmx_wkup {
 178
 179         ads7846_pins: pinmux_ads7846_pins {
 180                 pinctrl-single,pins = <
 181                         OMAP5_IOPAD(0x0042, PIN_INPUT_PULLDOWN | MUX_MODE6)  /* llib_wakereqin.gpio1_wk15 */
 182                 >;
 183         };
 184 };
 185
 186 &omap5_pmx_core {
 187         pinctrl-names = "default";
 188         pinctrl-0 = <
 189                         &led_gpio_pins
 190                         &usbhost_pins
 191         >;
 192
 193         led_gpio_pins: pinmux_led_gpio_pins {
 194                 pinctrl-single,pins = <
 195                         OMAP5_IOPAD(0x00b0, PIN_OUTPUT | MUX_MODE6) /* hsi2_caflag.gpio3_80 */
 196                 >;
 197         };
 198
 199         i2c1_pins: pinmux_i2c1_pins {
 200                 pinctrl-single,pins = <
 201                         OMAP5_IOPAD(0x01f2, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_pmic_scl */
 202                         OMAP5_IOPAD(0x01f4, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_pmic_sda */
 203                 >;
 204         };
 205
 206         i2c2_pins: pinmux_i2c2_pins {
 207                 pinctrl-single,pins = <
 208                         OMAP5_IOPAD(0x01b8, PIN_INPUT | MUX_MODE0) /* i2c2_scl */
 209                         OMAP5_IOPAD(0x01ba, PIN_INPUT | MUX_MODE0) /* i2c2_sda */
 210                 >;
 211         };
 212
 213         mmc1_pins: pinmux_mmc1_pins {
 214                 pinctrl-single,pins = <
 215                         OMAP5_IOPAD(0x01e2, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_clk */
 216                         OMAP5_IOPAD(0x01e4, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_cmd */
 217                         OMAP5_IOPAD(0x01e6, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data2 */
 218                         OMAP5_IOPAD(0x01e8, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data3 */
 219                         OMAP5_IOPAD(0x01ea, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data0 */
 220                         OMAP5_IOPAD(0x01ec, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data1 */
 221                 >;
 222         };
 223
 224         mmc2_pins: pinmux_mmc2_pins {
 225                 pinctrl-single,pins = <
 226                         OMAP5_IOPAD(0x0040, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_clk */
 227                         OMAP5_IOPAD(0x0042, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_cmd */
 228                         OMAP5_IOPAD(0x0044, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data0 */
 229                         OMAP5_IOPAD(0x0046, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data1 */
 230                         OMAP5_IOPAD(0x0048, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data2 */
 231                         OMAP5_IOPAD(0x004a, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data3 */
 232                         OMAP5_IOPAD(0x004c, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data4 */
 233                         OMAP5_IOPAD(0x004e, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data5 */
 234                         OMAP5_IOPAD(0x0050, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data6 */
 235                         OMAP5_IOPAD(0x0052, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data7 */
 236                 >;
 237         };
 238
 239         mmc3_pins: pinmux_mmc3_pins {
 240                 pinctrl-single,pins = <
 241                         OMAP5_IOPAD(0x01a4, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_clk */
 242                         OMAP5_IOPAD(0x01a6, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_cmd */
 243                         OMAP5_IOPAD(0x01a8, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data0 */
 244                         OMAP5_IOPAD(0x01aa, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data1 */
 245                         OMAP5_IOPAD(0x01ac, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data2 */
 246                         OMAP5_IOPAD(0x01ae, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data3 */
 247                 >;
 248         };
 249
 250         wlan_gpios_pins: pinmux_wlan_gpios_pins {
 251                 pinctrl-single,pins = <
 252                         OMAP5_IOPAD(0x019c, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* abemcpdm_ul_data.gpio4_109 */
 253                         OMAP5_IOPAD(0x019e, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* abemcpdm_dl_data.gpio4_110 */
 254                 >;
 255         };
 256
 257         usbhost_pins: pinmux_usbhost_pins {
 258                 pinctrl-single,pins = <
 259                         OMAP5_IOPAD(0x00c4, PIN_INPUT | MUX_MODE0)  /* usbb2_hsic_strobe */
 260                         OMAP5_IOPAD(0x00c6, PIN_INPUT | MUX_MODE0)  /* usbb2_hsic_data */
 261
 262                         OMAP5_IOPAD(0x01dc, PIN_INPUT | MUX_MODE0)  /* usbb3_hsic_strobe */
 263                         OMAP5_IOPAD(0x01de, PIN_INPUT | MUX_MODE0)  /* usbb3_hsic_data */
 264
 265                         OMAP5_IOPAD(0x00a8, PIN_OUTPUT | MUX_MODE6) /* hsi2_caready.gpio3_76 */
 266                         OMAP5_IOPAD(0x00b6, PIN_OUTPUT | MUX_MODE6) /* hsi2_acdata.gpio3_83 */
 267                 >;
 268         };
 269
 270         dss_hdmi_pins: pinmux_dss_hdmi_pins {
 271                 pinctrl-single,pins = <
 272                         OMAP5_IOPAD(0x013c, PIN_INPUT | MUX_MODE0) /* hdmi_cec */
 273                         OMAP5_IOPAD(0x0140, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_scl */
 274                         OMAP5_IOPAD(0x0142, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_sda */
 275                 >;
 276         };
 277
 278         lcd_pins: pinmux_lcd_pins {
 279                 pinctrl-single,pins = <
 280                         OMAP5_IOPAD(0x0172, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* timer11_pwm_evt.gpio8_227 */
 281                 >;
 282         };
 283
 284         hdmi_conn_pins: pinmux_hdmi_conn_pins {
 285                 pinctrl-single,pins = <
 286                         OMAP5_IOPAD(0x013e, PIN_INPUT | MUX_MODE6) /* hdmi_hpd.gpio7_193 */
 287                 >;
 288         };
 289
 290         dss_dpi_pins: pinmux_dss_dpi_pins {
 291                 pinctrl-single,pins = <
 292                         OMAP5_IOPAD(0x0104, PIN_OUTPUT | MUX_MODE3) /* rfbi_data15.dispc_data15 */
 293                         OMAP5_IOPAD(0x0106, PIN_OUTPUT | MUX_MODE3) /* rfbi_data14.dispc_data14 */
 294                         OMAP5_IOPAD(0x0108, PIN_OUTPUT | MUX_MODE3) /* rfbi_data13.dispc_data13 */
 295                         OMAP5_IOPAD(0x010a, PIN_OUTPUT | MUX_MODE3) /* rfbi_data12.dispc_data12 */
 296                         OMAP5_IOPAD(0x010c, PIN_OUTPUT | MUX_MODE3) /* rfbi_data11.dispc_data11 */
 297                         OMAP5_IOPAD(0x010e, PIN_OUTPUT | MUX_MODE3) /* rfbi_data10.dispc_data10 */
 298                         OMAP5_IOPAD(0x0110, PIN_OUTPUT | MUX_MODE3) /* rfbi_data9.dispc_data9 */
 299                         OMAP5_IOPAD(0x0112, PIN_OUTPUT | MUX_MODE3) /* rfbi_data8.dispc_data8 */
 300                         OMAP5_IOPAD(0x0114, PIN_OUTPUT | MUX_MODE3) /* rfbi_data7.dispc_data7 */
 301                         OMAP5_IOPAD(0x0116, PIN_OUTPUT | MUX_MODE3) /* rfbi_data6.dispc_data6 */
 302                         OMAP5_IOPAD(0x0118, PIN_OUTPUT | MUX_MODE3) /* rfbi_data5.dispc_data5 */
 303                         OMAP5_IOPAD(0x011a, PIN_OUTPUT | MUX_MODE3) /* rfbi_data4.dispc_data4 */
 304                         OMAP5_IOPAD(0x011c, PIN_OUTPUT | MUX_MODE3) /* rfbi_data3.dispc_data3 */
 305                         OMAP5_IOPAD(0x011e, PIN_OUTPUT | MUX_MODE3) /* rfbi_data2.dispc_data2 */
 306                         OMAP5_IOPAD(0x0120, PIN_OUTPUT | MUX_MODE3) /* rfbi_data1.dispc_data1 */
 307                         OMAP5_IOPAD(0x0122, PIN_OUTPUT | MUX_MODE3) /* rfbi_data0.dispc_data0 */
 308                         OMAP5_IOPAD(0x0124, PIN_OUTPUT | MUX_MODE3) /* rfbi_we.dispc_vsync */
 309                         OMAP5_IOPAD(0x0126, PIN_OUTPUT | MUX_MODE3) /* rfbi_cs0.dispc_hsync */
 310                         OMAP5_IOPAD(0x0128, PIN_OUTPUT | MUX_MODE3) /* rfbi_a0.dispc_de */
 311                         OMAP5_IOPAD(0x012a, PIN_OUTPUT | MUX_MODE3) /* rfbi_re.dispc_pclk */
 312                         OMAP5_IOPAD(0x012c, PIN_OUTPUT | MUX_MODE3) /* rfbi_hsync0.dispc_data17 */
 313                         OMAP5_IOPAD(0x012e, PIN_OUTPUT | MUX_MODE3) /* rfbi_te_vsync0.dispc_data16 */
 314                         OMAP5_IOPAD(0x0130, PIN_OUTPUT | MUX_MODE3) /* gpio6_182.dispc_data18 */
 315                         OMAP5_IOPAD(0x0132, PIN_OUTPUT | MUX_MODE3) /* gpio6_183.dispc_data19 */
 316                         OMAP5_IOPAD(0x0134, PIN_OUTPUT | MUX_MODE3) /* gpio6_184.dispc_data20 */
 317                         OMAP5_IOPAD(0x0136, PIN_OUTPUT | MUX_MODE3) /* gpio6_185.dispc_data21 */
 318                         OMAP5_IOPAD(0x0138, PIN_OUTPUT | MUX_MODE3) /* gpio6_186.dispc_data22 */
 319                         OMAP5_IOPAD(0x013a, PIN_OUTPUT | MUX_MODE3) /* gpio6_187.dispc_data23 */
 320                 >;
 321         };
 322
 323         mcspi2_pins: pinmux_mcspi1_pins {
 324                 pinctrl-single,pins = <
 325                         OMAP5_IOPAD(0x00fc, PIN_INPUT | MUX_MODE0) /* mcspi2_clk */
 326                         OMAP5_IOPAD(0x00fe, PIN_INPUT | MUX_MODE0) /* mcspi2_simo */
 327                         OMAP5_IOPAD(0x0100, PIN_INPUT | MUX_MODE0) /* mcspi2_somi */
 328                         OMAP5_IOPAD(0x0102, PIN_INPUT | MUX_MODE0) /* mcspi2_cs0 */
 329                 >;
 330         };
 331 };
 332
 333 &mcspi2 {
 334         pinctrl-names = "default";
 335         pinctrl-0 = <&mcspi2_pins>;
 336
 337         /* touch controller */
 338         ads7846@0 {
 339                 pinctrl-names = "default";
 340                 pinctrl-0 = <&ads7846_pins>;
 341
 342                 compatible = "ti,ads7846";
 343                 vcc-supply = <&ads7846reg>;
 344
 345                 reg = <0>;                              /* CS0 */
 346                 spi-max-frequency = <1500000>;
 347
 348                 interrupt-parent = <&gpio1>;
 349                 interrupts = <15 0>;                    /* gpio1_wk15 */
 350                 pendown-gpio = <&gpio1 15 GPIO_ACTIVE_HIGH>;
 351
 352
 353                 ti,x-min = /bits/ 16 <0x0>;
 354                 ti,x-max = /bits/ 16 <0x0fff>;
 355                 ti,y-min = /bits/ 16 <0x0>;
 356                 ti,y-max = /bits/ 16 <0x0fff>;
 357
 358                 ti,x-plate-ohms = /bits/ 16 <180>;
 359                 ti,pressure-max = /bits/ 16 <255>;
 360
 361                 ti,debounce-max = /bits/ 16 <30>;
 362                 ti,debounce-tol = /bits/ 16 <10>;
 363                 ti,debounce-rep = /bits/ 16 <1>;
 364
 365                 wakeup-source;
 366         };
 367 };
 368
 369 &mmc1 {
 370         pinctrl-names = "default";
 371         pinctrl-0 = <&mmc1_pins>;
 372         vmmc-supply = <&ldo9_reg>;
 373         bus-width = <4>;
 374 };
 375
 376 &mmc2 {
 377         pinctrl-names = "default";
 378         pinctrl-0 = <&mmc2_pins>;
 379         vmmc-supply = <&vmmcsd_fixed>;
 380         bus-width = <8>;
 381         ti,non-removable;
 382 };
 383
 384 &mmc3 {
 385         pinctrl-names = "default";
 386         pinctrl-0 = <
 387                 &mmc3_pins
 388                 &wlan_gpios_pins
 389         >;
 390         vmmc-supply = <&vwlan_fixed>;
 391         bus-width = <4>;
 392         ti,non-removable;
 393 };
 394
 395 &mmc4 {
 396         status = "disabled";
 397 };
 398
 399 &mmc5 {
 400         status = "disabled";
 401 };
 402
 403 &i2c1 {
 404         pinctrl-names = "default";
 405         pinctrl-0 = <&i2c1_pins>;
 406
 407         clock-frequency = <400000>;
 408
 409         at24@50 {
 410                 compatible = "atmel,24c02";
 411                 pagesize = <16>;
 412                 reg = <0x50>;
 413         };
 414
 415         palmas: palmas@48 {
 416                 compatible = "ti,palmas";
 417                 interrupts = <GIC_SPI 7 IRQ_TYPE_NONE>; /* IRQ_SYS_1N */
 418                 reg = <0x48>;
 419                 interrupt-controller;
 420                 #interrupt-cells = <2>;
 421                 ti,system-power-controller;
 422
 423                 extcon_usb3: palmas_usb {
 424                         compatible = "ti,palmas-usb-vid";
 425                         ti,enable-vbus-detection;
 426                         ti,enable-id-detection;
 427                         ti,wakeup;
 428                 };
 429
 430                 rtc {
 431                         compatible = "ti,palmas-rtc";
 432                         interrupt-parent = <&palmas>;
 433                         interrupts = <8 IRQ_TYPE_NONE>;
 434                 };
 435
 436                 palmas_pmic {
 437                         compatible = "ti,palmas-pmic";
 438                         interrupt-parent = <&palmas>;
 439                         interrupts = <14 IRQ_TYPE_NONE>;
 440                         interrupt-names = "short-irq";
 441
 442                         ti,ldo6-vibrator;
 443
 444                         regulators {
 445                                 smps123_reg: smps123 {
 446                                         /* VDD_OPP_MPU */
 447                                         regulator-name = "smps123";
 448                                         regulator-min-microvolt = < 600000>;
 449                                         regulator-max-microvolt = <1500000>;
 450                                         regulator-always-on;
 451                                         regulator-boot-on;
 452                                 };
 453
 454                                 smps45_reg: smps45 {
 455                                         /* VDD_OPP_MM */
 456                                         regulator-name = "smps45";
 457                                         regulator-min-microvolt = < 600000>;
 458                                         regulator-max-microvolt = <1310000>;
 459                                         regulator-always-on;
 460                                         regulator-boot-on;
 461                                 };
 462
 463                                 smps6_reg: smps6 {
 464                                         /* VDD_DDR3 - over VDD_SMPS6 */
 465                                         regulator-name = "smps6";
 466                                         regulator-min-microvolt = <1500000>;
 467                                         regulator-max-microvolt = <1500000>;
 468                                         regulator-always-on;
 469                                         regulator-boot-on;
 470                                 };
 471
 472                                 smps7_reg: smps7 {
 473                                         /* VDDS_1v8_OMAP over VDDS_1v8_MAIN */
 474                                         regulator-name = "smps7";
 475                                         regulator-min-microvolt = <1800000>;
 476                                         regulator-max-microvolt = <1800000>;
 477                                         regulator-always-on;
 478                                         regulator-boot-on;
 479                                 };
 480
 481                                 smps8_reg: smps8 {
 482                                         /* VDD_OPP_CORE */
 483                                         regulator-name = "smps8";
 484                                         regulator-min-microvolt = < 600000>;
 485                                         regulator-max-microvolt = <1310000>;
 486                                         regulator-always-on;
 487                                         regulator-boot-on;
 488                                 };
 489
 490                                 smps9_reg: smps9 {
 491                                         /* VDDA_2v1_AUD over VDD_2v1 */
 492                                         regulator-name = "smps9";
 493                                         regulator-min-microvolt = <3300000>;
 494                                         regulator-max-microvolt = <3300000>;
 495                                         ti,smps-range = <0x80>;
 496                                         regulator-always-on;
 497                                         regulator-boot-on;
 498                                 };
 499
 500                                 smps10_out2_reg: smps10_out2 {
 501                                         /* VBUS_5V_OTG */
 502                                         regulator-name = "smps10_out2";
 503                                         regulator-min-microvolt = <5000000>;
 504                                         regulator-max-microvolt = <5000000>;
 505                                         regulator-always-on;
 506                                         regulator-boot-on;
 507                                 };
 508
 509                                 smps10_out1_reg: smps10_out1 {
 510                                         /* VBUS_5V_OTG */
 511                                         regulator-name = "smps10_out1";
 512                                         regulator-min-microvolt = <5000000>;
 513                                         regulator-max-microvolt = <5000000>;
 514                                 };
 515
 516                                 ldo1_reg: ldo1 {
 517                                         /* VDDAPHY_CAM: vdda_csiport */
 518                                         regulator-name = "ldo1";
 519                                         regulator-min-microvolt = <1800000>;
 520                                         regulator-max-microvolt = <1800000>;
 521                                 };
 522
 523                                 ldo2_reg: ldo2 {
 524                                         /* VDD_3V3_WLAN */
 525                                         regulator-name = "ldo2";
 526                                         regulator-min-microvolt = <3300000>;
 527                                         regulator-max-microvolt = <3300000>;
 528                                         startup-delay-us = <1000>;
 529                                 };
 530
 531                                 ldo3_reg: ldo3 {
 532                                         /* VCC_1V5_AUD */
 533                                         regulator-name = "ldo3";
 534                                         regulator-min-microvolt = <1500000>;
 535                                         regulator-max-microvolt = <1500000>;
 536                                         regulator-always-on;
 537                                         regulator-boot-on;
 538                                 };
 539
 540                                 ldo4_reg: ldo4 {
 541                                         /* VDDAPHY_DISP: vdda_dsiport/hdmi */
 542                                         regulator-name = "ldo4";
 543                                         regulator-min-microvolt = <1800000>;
 544                                         regulator-max-microvolt = <1800000>;
 545                                 };
 546
 547                                 ldo5_reg: ldo5 {
 548                                         /* VDDA_1V8_PHY: usb/sata/hdmi.. */
 549                                         regulator-name = "ldo5";
 550                                         regulator-min-microvolt = <1800000>;
 551                                         regulator-max-microvolt = <1800000>;
 552                                         regulator-always-on;
 553                                         regulator-boot-on;
 554                                 };
 555
 556                                 ldo6_reg: ldo6 {
 557                                         /* VDDS_1V2_WKUP: hsic/ldo_emu_wkup */
 558                                         regulator-name = "ldo6";
 559                                         regulator-min-microvolt = <1200000>;
 560                                         regulator-max-microvolt = <1200000>;
 561                                         regulator-always-on;
 562                                         regulator-boot-on;
 563                                 };
 564
 565                                 ldo7_reg: ldo7 {
 566                                         /* VDD_VPP: vpp1 */
 567                                         regulator-name = "ldo7";
 568                                         regulator-min-microvolt = <2000000>;
 569                                         regulator-max-microvolt = <2000000>;
 570                                         /* Only for efuse reprograming! */
 571                                         status = "disabled";
 572                                 };
 573
 574                                 ldo8_reg: ldo8 {
 575                                         /* VDD_3V_GP: act led/serial console */
 576                                         regulator-name = "ldo8";
 577                                         regulator-min-microvolt = <3000000>;
 578                                         regulator-max-microvolt = <3000000>;
 579                                         regulator-always-on;
 580                                         regulator-boot-on;
 581                                 };
 582
 583                                 ldo9_reg: ldo9 {
 584                                         /* VCC_DV_SDIO: vdds_sdcard */
 585                                         regulator-name = "ldo9";
 586                                         regulator-min-microvolt = <1800000>;
 587                                         regulator-max-microvolt = <3000000>;
 588                                         regulator-boot-on;
 589                                 };
 590
 591                                 ldoln_reg: ldoln {
 592                                         /* VDDA_1v8_REF: vdds_osc/mm_l4per.. */
 593                                         regulator-name = "ldoln";
 594                                         regulator-min-microvolt = <1800000>;
 595                                         regulator-max-microvolt = <1800000>;
 596                                         regulator-always-on;
 597                                         regulator-boot-on;
 598                                 };
 599
 600                                 ldousb_reg: ldousb {
 601                                         /* VDDA_3V_USB: VDDA_USBHS33 */
 602                                         regulator-name = "ldousb";
 603                                         regulator-min-microvolt = <3250000>;
 604                                         regulator-max-microvolt = <3250000>;
 605                                         regulator-always-on;
 606                                         regulator-boot-on;
 607                                 };
 608
 609                                 regen3_reg: regen3 {
 610                                         /* REGEN3 controls LDO9 supply to card */
 611                                         regulator-name = "regen3";
 612                                         regulator-always-on;
 613                                         regulator-boot-on;
 614                                 };
 615                         };
 616                 };
 617         };
 618 };
 619
 620 &i2c2 {
 621         pinctrl-names = "default";
 622         pinctrl-0 = <&i2c2_pins>;
 623
 624         clock-frequency = <100000>;
 625 };
 626
 627 &usbhshost {
 628         port2-mode = "ehci-hsic";
 629         port3-mode = "ehci-hsic";
 630 };
 631
 632 &usbhsehci {
 633         phys = <0 &hsusb2_phy &hsusb3_phy>;
 634 };
 635
 636 &usb3 {
 637        extcon = <&extcon_usb3>;
 638        vbus-supply = <&smps10_out1_reg>;
 639 };
 640
 641 &cpu0 {
 642         cpu0-supply = <&smps123_reg>;
 643 };
 644
 645 &dss {
 646         status = "ok";
 647
 648         pinctrl-names = "default";
 649         pinctrl-0 = <&dss_dpi_pins>;
 650
 651         port {
 652                 #address-cells = <1>;
 653                 #size-cells = <0>;
 654
 655                 dpi_dvi_out: endpoint@0 {
 656                         reg = <0>;
 657                         remote-endpoint = <&tfp410_in>;
 658                         data-lines = <24>;
 659                 };
 660
 661                 dpi_lcd_out: endpoint@1 {
 662                         reg = <1>;
 663                         remote-endpoint = <&lcd_in>;
 664                         data-lines = <24>;
 665                 };
 666         };
 667 };
 668
 669 &dsi2 {
 670         status = "ok";
 671         vdd-supply = <&ldo4_reg>;
 672 };
 673
 674 &hdmi {
 675         status = "ok";
 676         vdda-supply = <&ldo4_reg>;
 677
 678         pinctrl-names = "default";
 679         pinctrl-0 = <&dss_hdmi_pins>;
 680
 681         port {
 682                 hdmi_out: endpoint {
 683                         remote-endpoint = <&hdmi_connector_in>;
 684                         lanes = <1 0 3 2 5 4 7 6>;
 685                 };
 686         };
 687 };