arch/arm/boot/dts/omap3-n900.dts

   1 /*
   2  * Copyright (C) 2013 Pavel Machek <pavel@ucw.cz>
   3  * Copyright (C) 2013-2014 Aaro Koskinen <aaro.koskinen@iki.fi>
   4  *
   5  * This program is free software; you can redistribute it and/or modify
   6  * it under the terms of the GNU General Public License version 2 (or later) as
   7  * published by the Free Software Foundation.
   8  */
   9
  10 /dts-v1/;
  11
  12 #include "omap34xx.dtsi"
  13 #include <dt-bindings/input/input.h>
  14
  15 /*
  16  * Default secure signed bootloader (Nokia X-Loader) does not enable L3 firewall
  17  * for omap AES HW crypto support. When linux kernel try to access memory of AES
  18  * blocks then kernel receive "Unhandled fault: external abort on non-linefetch"
  19  * and crash. Until somebody fix omap-aes.c and omap_hwmod_3xxx_data.c code (no
  20  * crash anymore) omap AES support will be disabled for all Nokia N900 devices.
  21  * There is "unofficial" version of bootloader which enables AES in L3 firewall
  22  * but it is not widely used and to prevent kernel crash rather AES is disabled.
  23  * There is also no runtime detection code if AES is disabled in L3 firewall...
  24  */
  25 &aes {
  26         status = "disabled";
  27 };
  28
  29 / {
  30         model = "Nokia N900";
  31         compatible = "nokia,omap3-n900", "ti,omap3430", "ti,omap3";
  32
  33         aliases {
  34                 i2c0;
  35                 i2c1 = &i2c1;
  36                 i2c2 = &i2c2;
  37                 i2c3 = &i2c3;
  38         };
  39
  40         cpus {
  41                 cpu@0 {
  42                         cpu0-supply = <&vcc>;
  43                 };
  44         };
  45
  46         leds {
  47                 compatible = "gpio-leds";
  48                 heartbeat {
  49                         label = "debug::sleep";
  50                         gpios = <&gpio6 2 GPIO_ACTIVE_HIGH>;  /* 162 */
  51                         linux,default-trigger = "default-on";
  52                         pinctrl-names = "default";
  53                         pinctrl-0 = <&debug_leds>;
  54                 };
  55         };
  56
  57         memory@80000000 {
  58                 device_type = "memory";
  59                 reg = <0x80000000 0x10000000>; /* 256 MB */
  60         };
  61
  62         gpio_keys {
  63                 compatible = "gpio-keys";
  64
  65                 camera_lens_cover {
  66                         label = "Camera Lens Cover";
  67                         gpios = <&gpio4 14 GPIO_ACTIVE_LOW>; /* 110 */
  68                         linux,input-type = <EV_SW>;
  69                         linux,code = <SW_CAMERA_LENS_COVER>;
  70                         linux,can-disable;
  71                 };
  72
  73                 camera_focus {
  74                         label = "Camera Focus";
  75                         gpios = <&gpio3 4 GPIO_ACTIVE_LOW>; /* 68 */
  76                         linux,code = <KEY_CAMERA_FOCUS>;
  77                         linux,can-disable;
  78                 };
  79
  80                 camera_capture {
  81                         label = "Camera Capture";
  82                         gpios = <&gpio3 5 GPIO_ACTIVE_LOW>; /* 69 */
  83                         linux,code = <KEY_CAMERA>;
  84                         linux,can-disable;
  85                 };
  86
  87                 lock_button {
  88                         label = "Lock Button";
  89                         gpios = <&gpio4 17 GPIO_ACTIVE_LOW>; /* 113 */
  90                         linux,code = <KEY_SCREENLOCK>;
  91                         linux,can-disable;
  92                 };
  93
  94                 keypad_slide {
  95                         label = "Keypad Slide";
  96                         gpios = <&gpio3 7 GPIO_ACTIVE_LOW>; /* 71 */
  97                         linux,input-type = <EV_SW>;
  98                         linux,code = <SW_KEYPAD_SLIDE>;
  99                         linux,can-disable;
 100                 };
 101
 102                 proximity_sensor {
 103                         label = "Proximity Sensor";
 104                         gpios = <&gpio3 25 GPIO_ACTIVE_HIGH>; /* 89 */
 105                         linux,input-type = <EV_SW>;
 106                         linux,code = <SW_FRONT_PROXIMITY>;
 107                         linux,can-disable;
 108                 };
 109         };
 110
 111         isp1707: isp1707 {
 112                 compatible = "nxp,isp1707";
 113                 nxp,enable-gpio = <&gpio3 3 GPIO_ACTIVE_HIGH>;
 114                 usb-phy = <&usb2_phy>;
 115         };
 116
 117         tv: connector {
 118                 compatible = "composite-video-connector";
 119                 label = "tv";
 120
 121                 port {
 122                         tv_connector_in: endpoint {
 123                                 remote-endpoint = <&venc_out>;
 124                         };
 125                 };
 126         };
 127
 128         sound: n900-audio {
 129                 compatible = "nokia,n900-audio";
 130
 131                 nokia,cpu-dai = <&mcbsp2>;
 132                 nokia,audio-codec = <&tlv320aic3x>, <&tlv320aic3x_aux>;
 133                 nokia,headphone-amplifier = <&tpa6130a2>;
 134
 135                 tvout-selection-gpios = <&gpio2 8 GPIO_ACTIVE_HIGH>; /* 40 */
 136                 jack-detection-gpios = <&gpio6 17 GPIO_ACTIVE_HIGH>; /* 177 */
 137                 eci-switch-gpios = <&gpio6 22 GPIO_ACTIVE_HIGH>; /* 182 */
 138                 speaker-amplifier-gpios = <&twl_gpio 7 GPIO_ACTIVE_HIGH>;
 139         };
 140
 141         battery: n900-battery {
 142                 compatible = "nokia,n900-battery";
 143                 io-channels = <&twl_madc 0>, <&twl_madc 4>, <&twl_madc 12>;
 144                 io-channel-names = "temp", "bsi", "vbat";
 145         };
 146
 147         rear_camera: camera@0 {
 148                 compatible = "linux,camera";
 149
 150                 module {
 151                         model = "TCM8341MD";
 152                         sensor = <&cam1>;
 153                 };
 154         };
 155
 156         pwm9: dmtimer-pwm {
 157                 compatible = "ti,omap-dmtimer-pwm";
 158                 #pwm-cells = <3>;
 159                 ti,timers = <&timer9>;
 160                 ti,clock-source = <0x00>; /* timer_sys_ck */
 161         };
 162
 163         ir: n900-ir {
 164                 compatible = "nokia,n900-ir";
 165                 pwms = <&pwm9 0 26316 0>; /* 38000 Hz */
 166         };
 167
 168         /* controlled (enabled/disabled) directly by bcm2048 and wl1251 */
 169         vctcxo: vctcxo {
 170                 compatible = "fixed-clock";
 171                 #clock-cells = <0>;
 172                 clock-frequency = <38400000>;
 173         };
 174 };
 175
 176 &isp {
 177         vdds_csib-supply = <&vaux2>;
 178
 179         pinctrl-names = "default";
 180         pinctrl-0 = <&camera_pins>;
 181
 182         ports {
 183                 port@1 {
 184                         reg = <1>;
 185
 186                         csi_isp: endpoint {
 187                                 remote-endpoint = <&csi_cam1>;
 188                                 bus-type = <3>; /* CCP2 */
 189                                 clock-lanes = <1>;
 190                                 data-lanes = <0>;
 191                                 lane-polarity = <0 0>;
 192                                 clock-inv = <0>;
 193                                 /* Select strobe = <1> for back camera, <0> for front camera */
 194                                 strobe = <1>;
 195                                 crc = <0>;
 196                         };
 197                 };
 198         };
 199 };
 200
 201 &omap3_pmx_core {
 202         pinctrl-names = "default";
 203
 204         uart2_pins: pinmux_uart2_pins {
 205                 pinctrl-single,pins = <
 206                         OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT_PULLUP | MUX_MODE0)         /* uart2_cts */
 207                         OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0)               /* uart2_rts */
 208                         OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0)               /* uart2_tx */
 209                         OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0)                /* uart2_rx */
 210                 >;
 211         };
 212
 213         uart3_pins: pinmux_uart3_pins {
 214                 pinctrl-single,pins = <
 215                         OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | MUX_MODE0)                /* uart3_rx */
 216                         OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0)               /* uart3_tx */
 217                 >;
 218         };
 219
 220         ethernet_pins: pinmux_ethernet_pins {
 221                 pinctrl-single,pins = <
 222                         OMAP3_CORE1_IOPAD(0x20b4, PIN_INPUT_PULLDOWN | MUX_MODE4)       /* gpmc_ncs3.gpio_54 */
 223                         OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE4)               /* dss_data16.gpio_86 */
 224                         OMAP3_CORE1_IOPAD(0x219c, PIN_OUTPUT | MUX_MODE4)               /* uart3_rts_sd.gpio_164 */
 225                 >;
 226         };
 227
 228         gpmc_pins: pinmux_gpmc_pins {
 229                 pinctrl-single,pins = <
 230
 231                         /* address lines */
 232                         OMAP3_CORE1_IOPAD(0x207a, PIN_OUTPUT | MUX_MODE0)       /* gpmc_a1.gpmc_a1 */
 233                         OMAP3_CORE1_IOPAD(0x207c, PIN_OUTPUT | MUX_MODE0)       /* gpmc_a2.gpmc_a2 */
 234                         OMAP3_CORE1_IOPAD(0x207e, PIN_OUTPUT | MUX_MODE0)       /* gpmc_a3.gpmc_a3 */
 235
 236                         /* data lines, gpmc_d0..d7 not muxable according to TRM */
 237                         OMAP3_CORE1_IOPAD(0x209e, PIN_INPUT | MUX_MODE0)        /* gpmc_d8.gpmc_d8 */
 238                         OMAP3_CORE1_IOPAD(0x20a0, PIN_INPUT | MUX_MODE0)        /* gpmc_d9.gpmc_d9 */
 239                         OMAP3_CORE1_IOPAD(0x20a2, PIN_INPUT | MUX_MODE0)        /* gpmc_d10.gpmc_d10 */
 240                         OMAP3_CORE1_IOPAD(0x20a4, PIN_INPUT | MUX_MODE0)        /* gpmc_d11.gpmc_d11 */
 241                         OMAP3_CORE1_IOPAD(0x20a6, PIN_INPUT | MUX_MODE0)        /* gpmc_d12.gpmc_d12 */
 242                         OMAP3_CORE1_IOPAD(0x20a8, PIN_INPUT | MUX_MODE0)        /* gpmc_d13.gpmc_d13 */
 243                         OMAP3_CORE1_IOPAD(0x20aa, PIN_INPUT | MUX_MODE0)        /* gpmc_d14.gpmc_d14 */
 244                         OMAP3_CORE1_IOPAD(0x20ac, PIN_INPUT | MUX_MODE0)        /* gpmc_d15.gpmc_d15 */
 245
 246                         /*
 247                          * gpmc_ncs0, gpmc_nadv_ale, gpmc_noe, gpmc_nwe, gpmc_wait0 not muxable
 248                          * according to TRM. OneNAND seems to require PIN_INPUT on clock.
 249                          */
 250                         OMAP3_CORE1_IOPAD(0x20b0, PIN_OUTPUT | MUX_MODE0)       /* gpmc_ncs1.gpmc_ncs1 */
 251                         OMAP3_CORE1_IOPAD(0x20be, PIN_INPUT | MUX_MODE0)        /* gpmc_clk.gpmc_clk */
 252                 >;
 253         };
 254
 255         i2c1_pins: pinmux_i2c1_pins {
 256                 pinctrl-single,pins = <
 257                         OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT | MUX_MODE0)                /* i2c1_scl */
 258                         OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT | MUX_MODE0)                /* i2c1_sda */
 259                 >;
 260         };
 261
 262         i2c2_pins: pinmux_i2c2_pins {
 263                 pinctrl-single,pins = <
 264                         OMAP3_CORE1_IOPAD(0x21be, PIN_INPUT | MUX_MODE0)                /* i2c2_scl */
 265                         OMAP3_CORE1_IOPAD(0x21c0, PIN_INPUT | MUX_MODE0)                /* i2c2_sda */
 266                 >;
 267         };
 268
 269         i2c3_pins: pinmux_i2c3_pins {
 270                 pinctrl-single,pins = <
 271                         OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT | MUX_MODE0)                /* i2c3_scl */
 272                         OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT | MUX_MODE0)                /* i2c3_sda */
 273                 >;
 274         };
 275
 276         debug_leds: pinmux_debug_led_pins {
 277                 pinctrl-single,pins = <
 278                         OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT | MUX_MODE4)       /* mcbsp1_clkx.gpio_162 */
 279                 >;
 280         };
 281
 282         mcspi4_pins: pinmux_mcspi4_pins {
 283                 pinctrl-single,pins = <
 284                         OMAP3_CORE1_IOPAD(0x218c, PIN_INPUT_PULLDOWN | MUX_MODE1) /* mcspi4_clk */
 285                         OMAP3_CORE1_IOPAD(0x2192, PIN_INPUT_PULLDOWN | MUX_MODE1) /* mcspi4_somi */
 286                         OMAP3_CORE1_IOPAD(0x2190, PIN_OUTPUT | MUX_MODE1) /* mcspi4_simo */
 287                         OMAP3_CORE1_IOPAD(0x2196, PIN_OUTPUT | MUX_MODE1) /* mcspi4_cs0 */
 288                 >;
 289         };
 290
 291         mmc1_pins: pinmux_mmc1_pins {
 292                 pinctrl-single,pins = <
 293                         OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk */
 294                         OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd */
 295                         OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0)         /* sdmmc1_dat0 */
 296                         OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1 */
 297                         OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2 */
 298                         OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3 */
 299                 >;
 300         };
 301
 302         mmc2_pins: pinmux_mmc2_pins {
 303                 pinctrl-single,pins = <
 304                         OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk */
 305                         OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd */
 306                         OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0)         /* sdmmc2_dat0 */
 307                         OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1 */
 308                         OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2 */
 309                         OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3 */
 310                         OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat4 */
 311                         OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat5 */
 312                         OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat6 */
 313                         OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat7 */
 314                 >;
 315         };
 316
 317         acx565akm_pins: pinmux_acx565akm_pins {
 318                 pinctrl-single,pins = <
 319                         OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT | MUX_MODE4)               /* RX51_LCD_RESET_GPIO */
 320                 >;
 321         };
 322
 323         dss_sdi_pins: pinmux_dss_sdi_pins {
 324                 pinctrl-single,pins = <
 325                         OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE1)   /* dss_data10.sdi_dat1n */
 326                         OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE1)   /* dss_data11.sdi_dat1p */
 327                         OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE1)   /* dss_data12.sdi_dat2n */
 328                         OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE1)   /* dss_data13.sdi_dat2p */
 329
 330                         OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT | MUX_MODE1)   /* dss_data22.sdi_clkp */
 331                         OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE1)   /* dss_data23.sdi_clkn */
 332                 >;
 333         };
 334
 335         wl1251_pins: pinmux_wl1251 {
 336                 pinctrl-single,pins = <
 337                         OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE4)               /* gpio 87 => wl1251 enable */
 338                         OMAP3_CORE1_IOPAD(0x208a, PIN_INPUT | MUX_MODE4)                /* gpio 42 => wl1251 irq */
 339                 >;
 340         };
 341
 342         ssi_pins: pinmux_ssi {
 343                 pinctrl-single,pins = <
 344                         OMAP3_CORE1_IOPAD(0x2180, PIN_INPUT_PULLUP | MUX_MODE1) /* ssi1_rdy_tx */
 345                         OMAP3_CORE1_IOPAD(0x217e, PIN_OUTPUT | MUX_MODE1)               /* ssi1_flag_tx */
 346                         OMAP3_CORE1_IOPAD(0x2182, PIN_INPUT | MUX_MODE4)                /* ssi1_wake_tx (cawake) */
 347                         OMAP3_CORE1_IOPAD(0x217c, PIN_OUTPUT | MUX_MODE1)               /* ssi1_dat_tx */
 348                         OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT | MUX_MODE1)                /* ssi1_dat_rx */
 349                         OMAP3_CORE1_IOPAD(0x2186, PIN_INPUT | MUX_MODE1)                /* ssi1_flag_rx */
 350                         OMAP3_CORE1_IOPAD(0x2188, PIN_OUTPUT | MUX_MODE1)               /* ssi1_rdy_rx */
 351                         OMAP3_CORE1_IOPAD(0x218a, PIN_OUTPUT | MUX_MODE1)               /* ssi1_wake */
 352                 >;
 353         };
 354
 355         modem_pins: pinmux_modem {
 356                 pinctrl-single,pins = <
 357                         OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT | MUX_MODE4)               /* gpio 70 => cmt_apeslpx */
 358                         OMAP3_CORE1_IOPAD(0x20e0, PIN_INPUT | MUX_MODE4)                /* gpio 72 => ape_rst_rq */
 359                         OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE4)               /* gpio 73 => cmt_rst_rq */
 360                         OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT | MUX_MODE4)               /* gpio 74 => cmt_en */
 361                         OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT | MUX_MODE4)               /* gpio 75 => cmt_rst */
 362                         OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4)               /* gpio 157 => cmt_bsi */
 363                 >;
 364         };
 365
 366         camera_pins: pinmux_camera {
 367                 pinctrl-single,pins = <
 368                         OMAP3_CORE1_IOPAD(0x210c, PIN_OUTPUT | MUX_MODE7)       /* cam_hs */
 369                         OMAP3_CORE1_IOPAD(0x210e, PIN_OUTPUT | MUX_MODE7)       /* cam_vs */
 370                         OMAP3_CORE1_IOPAD(0x2110, PIN_OUTPUT | MUX_MODE0)       /* cam_xclka */
 371                         OMAP3_CORE1_IOPAD(0x211e, PIN_OUTPUT | MUX_MODE7)       /* cam_d4 */
 372                         OMAP3_CORE1_IOPAD(0x2122, PIN_INPUT | MUX_MODE0)        /* cam_d6 */
 373                         OMAP3_CORE1_IOPAD(0x2124, PIN_INPUT | MUX_MODE0)        /* cam_d7 */
 374                         OMAP3_CORE1_IOPAD(0x2126, PIN_INPUT | MUX_MODE0)        /* cam_d8 */
 375                         OMAP3_CORE1_IOPAD(0x2128, PIN_INPUT | MUX_MODE0)        /* cam_d9 */
 376                         OMAP3_CORE1_IOPAD(0x212a, PIN_OUTPUT | MUX_MODE7)       /* cam_d10 */
 377                         OMAP3_CORE1_IOPAD(0x212e, PIN_OUTPUT | MUX_MODE7)       /* cam_xclkb */
 378                         OMAP3_CORE1_IOPAD(0x2132, PIN_OUTPUT | MUX_MODE0)       /* cam_strobe */
 379                 >;
 380         };
 381 };
 382
 383 &i2c1 {
 384         pinctrl-names = "default";
 385         pinctrl-0 = <&i2c1_pins>;
 386
 387         clock-frequency = <2200000>;
 388
 389         twl: twl@48 {
 390                 reg = <0x48>;
 391                 interrupts = <7>; /* SYS_NIRQ cascaded to intc */
 392                 interrupt-parent = <&intc>;
 393         };
 394 };
 395
 396 #include "twl4030.dtsi"
 397 #include "twl4030_omap3.dtsi"
 398
 399 &vaux1 {
 400         regulator-name = "V28";
 401         regulator-min-microvolt = <2800000>;
 402         regulator-max-microvolt = <2800000>;
 403         regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
 404         regulator-always-on; /* due to battery cover sensor */
 405 };
 406
 407 &vaux2 {
 408         regulator-name = "VCSI";
 409         regulator-min-microvolt = <1800000>;
 410         regulator-max-microvolt = <1800000>;
 411         regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
 412 };
 413
 414 &vaux3 {
 415         regulator-name = "VMMC2_30";
 416         regulator-min-microvolt = <2800000>;
 417         regulator-max-microvolt = <3000000>;
 418         regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
 419 };
 420
 421 &vaux4 {
 422         regulator-name = "VCAM_ANA_28";
 423         regulator-min-microvolt = <2800000>;
 424         regulator-max-microvolt = <2800000>;
 425         regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
 426 };
 427
 428 &vmmc1 {
 429         regulator-name = "VMMC1";
 430         regulator-min-microvolt = <1850000>;
 431         regulator-max-microvolt = <3150000>;
 432         regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
 433 };
 434
 435 &vmmc2 {
 436         regulator-name = "V28_A";
 437         regulator-min-microvolt = <2800000>;
 438         regulator-max-microvolt = <3000000>;
 439         regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
 440         regulator-always-on; /* due VIO leak to AIC34 VDDs */
 441 };
 442
 443 &vpll1 {
 444         regulator-name = "VPLL";
 445         regulator-min-microvolt = <1800000>;
 446         regulator-max-microvolt = <1800000>;
 447         regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
 448         regulator-always-on;
 449 };
 450
 451 &vpll2 {
 452         regulator-name = "VSDI_CSI";
 453         regulator-min-microvolt = <1800000>;
 454         regulator-max-microvolt = <1800000>;
 455         regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
 456         regulator-always-on;
 457 };
 458
 459 &vsim {
 460         regulator-name = "VMMC2_IO_18";
 461         regulator-min-microvolt = <1800000>;
 462         regulator-max-microvolt = <1800000>;
 463         regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
 464 };
 465
 466 &vio {
 467         regulator-name = "VIO";
 468         regulator-min-microvolt = <1800000>;
 469         regulator-max-microvolt = <1800000>;
 470 };
 471
 472 &vintana1 {
 473         regulator-name = "VINTANA1";
 474         /* fixed to 1500000 */
 475         regulator-always-on;
 476 };
 477
 478 &vintana2 {
 479         regulator-name = "VINTANA2";
 480         regulator-min-microvolt = <2750000>;
 481         regulator-max-microvolt = <2750000>;
 482         regulator-always-on;
 483 };
 484
 485 &vintdig {
 486         regulator-name = "VINTDIG";
 487         /* fixed to 1500000 */
 488         regulator-always-on;
 489 };
 490
 491 &twl {
 492         twl_audio: audio {
 493                 compatible = "ti,twl4030-audio";
 494                 ti,enable-vibra = <1>;
 495         };
 496
 497         twl_power: power {
 498                 compatible = "ti,twl4030-power-n900", "ti,twl4030-power-idle-osc-off";
 499                 ti,use_poweroff;
 500         };
 501 };
 502
 503 &twl_keypad {
 504         linux,keymap = < MATRIX_KEY(0x00, 0x00, KEY_Q)
 505                          MATRIX_KEY(0x00, 0x01, KEY_O)
 506                          MATRIX_KEY(0x00, 0x02, KEY_P)
 507                          MATRIX_KEY(0x00, 0x03, KEY_COMMA)
 508                          MATRIX_KEY(0x00, 0x04, KEY_BACKSPACE)
 509                          MATRIX_KEY(0x00, 0x06, KEY_A)
 510                          MATRIX_KEY(0x00, 0x07, KEY_S)
 511
 512                          MATRIX_KEY(0x01, 0x00, KEY_W)
 513                          MATRIX_KEY(0x01, 0x01, KEY_D)
 514                          MATRIX_KEY(0x01, 0x02, KEY_F)
 515                          MATRIX_KEY(0x01, 0x03, KEY_G)
 516                          MATRIX_KEY(0x01, 0x04, KEY_H)
 517                          MATRIX_KEY(0x01, 0x05, KEY_J)
 518                          MATRIX_KEY(0x01, 0x06, KEY_K)
 519                          MATRIX_KEY(0x01, 0x07, KEY_L)
 520
 521                          MATRIX_KEY(0x02, 0x00, KEY_E)
 522                          MATRIX_KEY(0x02, 0x01, KEY_DOT)
 523                          MATRIX_KEY(0x02, 0x02, KEY_UP)
 524                          MATRIX_KEY(0x02, 0x03, KEY_ENTER)
 525                          MATRIX_KEY(0x02, 0x05, KEY_Z)
 526                          MATRIX_KEY(0x02, 0x06, KEY_X)
 527                          MATRIX_KEY(0x02, 0x07, KEY_C)
 528                          MATRIX_KEY(0x02, 0x08, KEY_F9)
 529
 530                          MATRIX_KEY(0x03, 0x00, KEY_R)
 531                          MATRIX_KEY(0x03, 0x01, KEY_V)
 532                          MATRIX_KEY(0x03, 0x02, KEY_B)
 533                          MATRIX_KEY(0x03, 0x03, KEY_N)
 534                          MATRIX_KEY(0x03, 0x04, KEY_M)
 535                          MATRIX_KEY(0x03, 0x05, KEY_SPACE)
 536                          MATRIX_KEY(0x03, 0x06, KEY_SPACE)
 537                          MATRIX_KEY(0x03, 0x07, KEY_LEFT)
 538
 539                          MATRIX_KEY(0x04, 0x00, KEY_T)
 540                          MATRIX_KEY(0x04, 0x01, KEY_DOWN)
 541                          MATRIX_KEY(0x04, 0x02, KEY_RIGHT)
 542                          MATRIX_KEY(0x04, 0x04, KEY_LEFTCTRL)
 543                          MATRIX_KEY(0x04, 0x05, KEY_RIGHTALT)
 544                          MATRIX_KEY(0x04, 0x06, KEY_LEFTSHIFT)
 545                          MATRIX_KEY(0x04, 0x08, KEY_F10)
 546
 547                          MATRIX_KEY(0x05, 0x00, KEY_Y)
 548                          MATRIX_KEY(0x05, 0x08, KEY_F11)
 549
 550                          MATRIX_KEY(0x06, 0x00, KEY_U)
 551
 552                          MATRIX_KEY(0x07, 0x00, KEY_I)
 553                          MATRIX_KEY(0x07, 0x01, KEY_F7)
 554                          MATRIX_KEY(0x07, 0x02, KEY_F8)
 555                          >;
 556 };
 557
 558 &twl_gpio {
 559         ti,pullups      = <0x0>;
 560         ti,pulldowns    = <0x03ff3f>; /* BIT(0..5) | BIT(8..17) */
 561 };
 562
 563 &i2c2 {
 564         pinctrl-names = "default";
 565         pinctrl-0 = <&i2c2_pins>;
 566
 567         clock-frequency = <100000>;
 568
 569         tlv320aic3x: tlv320aic3x@18 {
 570                 compatible = "ti,tlv320aic3x";
 571                 reg = <0x18>;
 572                 gpio-reset = <&gpio2 28 GPIO_ACTIVE_HIGH>; /* 60 */
 573                 ai3x-gpio-func = <
 574                         0 /* AIC3X_GPIO1_FUNC_DISABLED */
 575                         5 /* AIC3X_GPIO2_FUNC_DIGITAL_MIC_INPUT */
 576                 >;
 577
 578                 AVDD-supply = <&vmmc2>;
 579                 DRVDD-supply = <&vmmc2>;
 580                 IOVDD-supply = <&vio>;
 581                 DVDD-supply = <&vio>;
 582
 583                 ai3x-micbias-vg = <1>;
 584         };
 585
 586         tlv320aic3x_aux: tlv320aic3x@19 {
 587                 compatible = "ti,tlv320aic3x";
 588                 reg = <0x19>;
 589                 gpio-reset = <&gpio2 28 GPIO_ACTIVE_HIGH>; /* 60 */
 590
 591                 AVDD-supply = <&vmmc2>;
 592                 DRVDD-supply = <&vmmc2>;
 593                 IOVDD-supply = <&vio>;
 594                 DVDD-supply = <&vio>;
 595
 596                 ai3x-micbias-vg = <2>;
 597         };
 598
 599         tsl2563: tsl2563@29 {
 600                 compatible = "amstaos,tsl2563";
 601                 reg = <0x29>;
 602
 603                 amstaos,cover-comp-gain = <16>;
 604         };
 605
 606         adp1653: led-controller@30 {
 607                 compatible = "adi,adp1653";
 608                 reg = <0x30>;
 609                 enable-gpios = <&gpio3 24 GPIO_ACTIVE_HIGH>; /* 88 */
 610
 611                 flash {
 612                         flash-timeout-us = <500000>;
 613                         flash-max-microamp = <320000>;
 614                         led-max-microamp = <50000>;
 615                 };
 616                 indicator {
 617                         led-max-microamp = <17500>;
 618                 };
 619         };
 620
 621         lp5523: lp5523@32 {
 622                 compatible = "national,lp5523";
 623                 reg = <0x32>;
 624                 clock-mode = /bits/ 8 <0>; /* LP55XX_CLOCK_AUTO */
 625                 enable-gpio = <&gpio2 9 GPIO_ACTIVE_HIGH>; /* 41 */
 626
 627                 chan0 {
 628                         chan-name = "lp5523:kb1";
 629                         led-cur = /bits/ 8 <50>;
 630                         max-cur = /bits/ 8 <100>;
 631                 };
 632
 633                 chan1 {
 634                         chan-name = "lp5523:kb2";
 635                         led-cur = /bits/ 8 <50>;
 636                         max-cur = /bits/ 8 <100>;
 637                 };
 638
 639                 chan2 {
 640                         chan-name = "lp5523:kb3";
 641                         led-cur = /bits/ 8 <50>;
 642                         max-cur = /bits/ 8 <100>;
 643                 };
 644
 645                 chan3 {
 646                         chan-name = "lp5523:kb4";
 647                         led-cur = /bits/ 8 <50>;
 648                         max-cur = /bits/ 8 <100>;
 649                 };
 650
 651                 chan4 {
 652                         chan-name = "lp5523:b";
 653                         led-cur = /bits/ 8 <50>;
 654                         max-cur = /bits/ 8 <100>;
 655                 };
 656
 657                 chan5 {
 658                         chan-name = "lp5523:g";
 659                         led-cur = /bits/ 8 <50>;
 660                         max-cur = /bits/ 8 <100>;
 661                 };
 662
 663                 chan6 {
 664                         chan-name = "lp5523:r";
 665                         led-cur = /bits/ 8 <50>;
 666                         max-cur = /bits/ 8 <100>;
 667                 };
 668
 669                 chan7 {
 670                         chan-name = "lp5523:kb5";
 671                         led-cur = /bits/ 8 <50>;
 672                         max-cur = /bits/ 8 <100>;
 673                 };
 674
 675                 chan8 {
 676                         chan-name = "lp5523:kb6";
 677                         led-cur = /bits/ 8 <50>;
 678                         max-cur = /bits/ 8 <100>;
 679                 };
 680         };
 681
 682         bq27200: bq27200@55 {
 683                 compatible = "ti,bq27200";
 684                 reg = <0x55>;
 685         };
 686
 687         /* Stereo headphone amplifier */
 688         tpa6130a2: tpa6130a2@60 {
 689                 compatible = "ti,tpa6130a2";
 690                 reg = <0x60>;
 691
 692                 Vdd-supply = <&vmmc2>;
 693
 694                 power-gpio = <&gpio4 2 GPIO_ACTIVE_HIGH>; /* 98 */
 695         };
 696
 697         si4713: si4713@63 {
 698                 compatible = "silabs,si4713";
 699                 reg = <0x63>;
 700
 701                 interrupts-extended = <&gpio2 21 IRQ_TYPE_EDGE_FALLING>; /* 53 */
 702                 reset-gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>; /* 163 */
 703                 vio-supply = <&vio>;
 704                 vdd-supply = <&vaux1>;
 705         };
 706
 707         bq24150a: bq24150a@6b {
 708                 compatible = "ti,bq24150a";
 709                 reg = <0x6b>;
 710
 711                 ti,current-limit = <100>;
 712                 ti,weak-battery-voltage = <3400>;
 713                 ti,battery-regulation-voltage = <4200>;
 714                 ti,charge-current = <650>;
 715                 ti,termination-current = <100>;
 716                 ti,resistor-sense = <68>;
 717
 718                 ti,usb-charger-detection = <&isp1707>;
 719         };
 720 };
 721
 722 &i2c3 {
 723         pinctrl-names = "default";
 724         pinctrl-0 = <&i2c3_pins>;
 725
 726         clock-frequency = <400000>;
 727
 728         lis302dl: lis3lv02d@1d {
 729                 compatible = "st,lis3lv02d";
 730                 reg = <0x1d>;
 731
 732                 Vdd-supply = <&vaux1>;
 733                 Vdd_IO-supply = <&vio>;
 734
 735                 interrupt-parent = <&gpio6>;
 736                 interrupts = <21 20>; /* 181 and 180 */
 737
 738                 /* click flags */
 739                 st,click-single-x;
 740                 st,click-single-y;
 741                 st,click-single-z;
 742
 743                 /* Limits are 0.5g * value */
 744                 st,click-threshold-x = <8>;
 745                 st,click-threshold-y = <8>;
 746                 st,click-threshold-z = <10>;
 747
 748                 /* Click must be longer than time limit */
 749                 st,click-time-limit = <9>;
 750
 751                 /* Kind of debounce filter */
 752                 st,click-latency = <50>;
 753
 754                 /* Interrupt line 2 for click detection */
 755                 st,irq2-click;
 756
 757                 st,wakeup-x-hi;
 758                 st,wakeup-y-hi;
 759                 st,wakeup-threshold = <(800/18)>; /* millig-value / 18 to get HW values */
 760
 761                 st,wakeup2-z-hi;
 762                 st,wakeup2-threshold = <(900/18)>; /* millig-value / 18 to get HW values */
 763
 764                 st,hipass1-disable;
 765                 st,hipass2-disable;
 766
 767                 st,axis-x = <1>;    /* LIS3_DEV_X */
 768                 st,axis-y = <(-2)>; /* LIS3_INV_DEV_Y */
 769                 st,axis-z = <(-3)>; /* LIS3_INV_DEV_Z */
 770
 771                 st,min-limit-x = <(-32)>;
 772                 st,min-limit-y = <3>;
 773                 st,min-limit-z = <3>;
 774
 775                 st,max-limit-x = <(-3)>;
 776                 st,max-limit-y = <32>;
 777                 st,max-limit-z = <32>;
 778         };
 779
 780         cam1: camera@3e {
 781                 compatible = "toshiba,et8ek8";
 782                 reg = <0x3e>;
 783
 784                 vana-supply = <&vaux4>;
 785
 786                 clocks = <&isp 0>;
 787                 clock-names = "extclk";
 788                 clock-frequency = <9600000>;
 789
 790                 reset-gpio = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* 102 */
 791
 792                 port {
 793                         csi_cam1: endpoint {
 794                                 bus-type = <3>; /* CCP2 */
 795                                 strobe = <1>;
 796                                 clock-inv = <0>;
 797                                 crc = <1>;
 798
 799                                 remote-endpoint = <&csi_isp>;
 800                         };
 801                 };
 802         };
 803
 804         /* D/A converter for auto-focus */
 805         ad5820: dac@0c {
 806                 compatible = "adi,ad5820";
 807                 reg = <0x0c>;
 808
 809                 VANA-supply = <&vaux4>;
 810
 811                 #io-channel-cells = <0>;
 812         };
 813 };
 814
 815 &mmc1 {
 816         pinctrl-names = "default";
 817         pinctrl-0 = <&mmc1_pins>;
 818         vmmc-supply = <&vmmc1>;
 819         bus-width = <4>;
 820         /* For debugging, it is often good idea to remove this GPIO.
 821            It means you can remove back cover (to reboot by removing
 822            battery) and still use the MMC card. */
 823         cd-gpios = <&gpio6 0 GPIO_ACTIVE_HIGH>; /* 160 */
 824 };
 825
 826 /* most boards use vaux3, only some old versions use vmmc2 instead */
 827 &mmc2 {
 828         pinctrl-names = "default";
 829         pinctrl-0 = <&mmc2_pins>;
 830         vmmc-supply = <&vaux3>;
 831         vqmmc-supply = <&vsim>;
 832         bus-width = <8>;
 833         non-removable;
 834         no-sdio;
 835         no-sd;
 836 };
 837
 838 &mmc3 {
 839         status = "disabled";
 840 };
 841
 842 &gpmc {
 843         ranges = <0 0 0x01000000 0x01000000>,   /* 16 MB for OneNAND */
 844                  <1 0 0x02000000 0x01000000>;   /* 16 MB for smc91c96 */
 845         pinctrl-names = "default";
 846         pinctrl-0 = <&gpmc_pins>;
 847
 848         /* sys_ndmareq1 could be used by the driver, not as gpio65 though */
 849         onenand@0,0 {
 850                 #address-cells = <1>;
 851                 #size-cells = <1>;
 852                 reg = <0 0 0x20000>;    /* CS0, offset 0, IO size 128K */
 853
 854                 gpmc,sync-read;
 855                 gpmc,sync-write;
 856                 gpmc,burst-length = <16>;
 857                 gpmc,burst-read;
 858                 gpmc,burst-wrap;
 859                 gpmc,burst-write;
 860                 gpmc,device-width = <2>; /* GPMC_DEVWIDTH_16BIT */
 861                 gpmc,mux-add-data = <2>; /* GPMC_MUX_AD */
 862                 gpmc,cs-on-ns = <0>;
 863                 gpmc,cs-rd-off-ns = <87>;
 864                 gpmc,cs-wr-off-ns = <87>;
 865                 gpmc,adv-on-ns = <0>;
 866                 gpmc,adv-rd-off-ns = <10>;
 867                 gpmc,adv-wr-off-ns = <10>;
 868                 gpmc,oe-on-ns = <15>;
 869                 gpmc,oe-off-ns = <87>;
 870                 gpmc,we-on-ns = <0>;
 871                 gpmc,we-off-ns = <87>;
 872                 gpmc,rd-cycle-ns = <112>;
 873                 gpmc,wr-cycle-ns = <112>;
 874                 gpmc,access-ns = <81>;
 875                 gpmc,page-burst-access-ns = <15>;
 876                 gpmc,bus-turnaround-ns = <0>;
 877                 gpmc,cycle2cycle-delay-ns = <0>;
 878                 gpmc,wait-monitoring-ns = <0>;
 879                 gpmc,clk-activation-ns = <5>;
 880                 gpmc,wr-data-mux-bus-ns = <30>;
 881                 gpmc,wr-access-ns = <81>;
 882                 gpmc,sync-clk-ps = <15000>;
 883
 884                 /*
 885                  * MTD partition table corresponding to Nokia's
 886                  * Maemo 5 (Fremantle) release.
 887                  */
 888                 partition@0 {
 889                         label = "bootloader";
 890                         reg = <0x00000000 0x00020000>;
 891                         read-only;
 892                 };
 893                 partition@1 {
 894                         label = "config";
 895                         reg = <0x00020000 0x00060000>;
 896                 };
 897                 partition@2 {
 898                         label = "log";
 899                         reg = <0x00080000 0x00040000>;
 900                 };
 901                 partition@3 {
 902                         label = "kernel";
 903                         reg = <0x000c0000 0x00200000>;
 904                 };
 905                 partition@4 {
 906                         label = "initfs";
 907                         reg = <0x002c0000 0x00200000>;
 908                 };
 909                 partition@5 {
 910                         label = "rootfs";
 911                         reg = <0x004c0000 0x0fb40000>;
 912                 };
 913         };
 914
 915         /* Ethernet is on some early development boards and qemu */
 916         ethernet@gpmc {
 917                 compatible = "smsc,lan91c94";
 918                 interrupt-parent = <&gpio2>;
 919                 interrupts = <22 IRQ_TYPE_LEVEL_HIGH>;  /* gpio54 */
 920                 reg = <1 0 0xf>;                /* 16 byte IO range */
 921                 bank-width = <2>;
 922                 pinctrl-names = "default";
 923                 pinctrl-0 = <&ethernet_pins>;
 924                 power-gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>;     /* gpio86 */
 925                 reset-gpios = <&gpio6 4 GPIO_ACTIVE_HIGH>;      /* gpio164 */
 926                 gpmc,device-width = <2>;
 927                 gpmc,sync-clk-ps = <0>;
 928                 gpmc,cs-on-ns = <0>;
 929                 gpmc,cs-rd-off-ns = <48>;
 930                 gpmc,cs-wr-off-ns = <24>;
 931                 gpmc,adv-on-ns = <0>;
 932                 gpmc,adv-rd-off-ns = <0>;
 933                 gpmc,adv-wr-off-ns = <0>;
 934                 gpmc,we-on-ns = <12>;
 935                 gpmc,we-off-ns = <18>;
 936                 gpmc,oe-on-ns = <12>;
 937                 gpmc,oe-off-ns = <48>;
 938                 gpmc,page-burst-access-ns = <0>;
 939                 gpmc,access-ns = <42>;
 940                 gpmc,rd-cycle-ns = <180>;
 941                 gpmc,wr-cycle-ns = <180>;
 942                 gpmc,bus-turnaround-ns = <0>;
 943                 gpmc,cycle2cycle-delay-ns = <0>;
 944                 gpmc,wait-monitoring-ns = <0>;
 945                 gpmc,clk-activation-ns = <0>;
 946                 gpmc,wr-access-ns = <0>;
 947                 gpmc,wr-data-mux-bus-ns = <12>;
 948         };
 949 };
 950
 951 &mcspi1 {
 952         /*
 953          * For some reason, touchscreen is necessary for screen to work at
 954          * all on real hw. It works well without it on emulator.
 955          *
 956          * Also... order in the device tree actually matters here.
 957          */
 958         tsc2005@0 {
 959                 compatible = "ti,tsc2005";
 960                 spi-max-frequency = <6000000>;
 961                 reg = <0>;
 962
 963                 vio-supply = <&vio>;
 964
 965                 reset-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* 104 */
 966                 interrupts-extended = <&gpio4 4 IRQ_TYPE_EDGE_RISING>; /* 100 */
 967
 968                 touchscreen-fuzz-x = <4>;
 969                 touchscreen-fuzz-y = <7>;
 970                 touchscreen-fuzz-pressure = <2>;
 971                 touchscreen-size-x = <4096>;
 972                 touchscreen-size-y = <4096>;
 973                 touchscreen-max-pressure = <2048>;
 974
 975                 ti,x-plate-ohms = <280>;
 976                 ti,esd-recovery-timeout-ms = <8000>;
 977         };
 978
 979         acx565akm@2 {
 980                 compatible = "sony,acx565akm";
 981                 spi-max-frequency = <6000000>;
 982                 reg = <2>;
 983
 984                 pinctrl-names = "default";
 985                 pinctrl-0 = <&acx565akm_pins>;
 986
 987                 label = "lcd";
 988                 reset-gpios = <&gpio3 26 GPIO_ACTIVE_HIGH>; /* 90 */
 989
 990                 port {
 991                         lcd_in: endpoint {
 992                                 remote-endpoint = <&sdi_out>;
 993                         };
 994                 };
 995         };
 996 };
 997
 998 &mcspi4 {
 999         pinctrl-names = "default";
1000         pinctrl-0 = <&mcspi4_pins>;
1001
1002         wl1251@0 {
1003                 pinctrl-names = "default";
1004                 pinctrl-0 = <&wl1251_pins>;
1005
1006                 vio-supply = <&vio>;
1007
1008                 compatible = "ti,wl1251";
1009                 reg = <0>;
1010                 spi-max-frequency = <48000000>;
1011
1012                 spi-cpol;
1013                 spi-cpha;
1014
1015                 ti,power-gpio = <&gpio3 23 GPIO_ACTIVE_HIGH>; /* 87 */
1016
1017                 interrupt-parent = <&gpio2>;
1018                 interrupts = <10 IRQ_TYPE_NONE>; /* gpio line 42 */
1019
1020                 clocks = <&vctcxo>;
1021         };
1022 };
1023
1024 &usb_otg_hs {
1025         interface-type = <0>;
1026         usb-phy = <&usb2_phy>;
1027         phys = <&usb2_phy>;
1028         phy-names = "usb2-phy";
1029         mode = <2>;
1030         power = <50>;
1031 };
1032
1033 &uart1 {
1034         status = "disabled";
1035 };
1036
1037 &uart2 {
1038         pinctrl-names = "default";
1039         pinctrl-0 = <&uart2_pins>;
1040
1041         bcm2048: bluetooth {
1042                 compatible = "brcm,bcm2048-nokia", "nokia,h4p-bluetooth";
1043                 reset-gpios = <&gpio3 27 GPIO_ACTIVE_LOW>; /* 91 */
1044                 host-wakeup-gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>; /* 101 */
1045                 bluetooth-wakeup-gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>; /* 37 */
1046                 clocks = <&vctcxo>;
1047                 clock-names = "sysclk";
1048         };
1049 };
1050
1051 &uart3 {
1052         interrupts-extended = <&intc 74 &omap3_pmx_core OMAP3_UART3_RX>;
1053         pinctrl-names = "default";
1054         pinctrl-0 = <&uart3_pins>;
1055 };
1056
1057 &dss {
1058         status = "ok";
1059
1060         pinctrl-names = "default";
1061         pinctrl-0 = <&dss_sdi_pins>;
1062
1063         vdds_sdi-supply = <&vaux1>;
1064
1065         ports {
1066                 #address-cells = <1>;
1067                 #size-cells = <0>;
1068
1069                 port@1 {
1070                         reg = <1>;
1071
1072                         sdi_out: endpoint {
1073                                 remote-endpoint = <&lcd_in>;
1074                                 datapairs = <2>;
1075                         };
1076                 };
1077         };
1078 };
1079
1080 &venc {
1081         status = "ok";
1082
1083         vdda-supply = <&vdac>;
1084
1085         port {
1086                 venc_out: endpoint {
1087                         remote-endpoint = <&tv_connector_in>;
1088                         ti,channels = <1>;
1089                 };
1090         };
1091 };
1092
1093 &mcbsp2 {
1094         status = "ok";
1095 };
1096
1097 &ssi_port1 {
1098         pinctrl-names = "default";
1099         pinctrl-0 = <&ssi_pins>;
1100
1101         ti,ssi-cawake-gpio = <&gpio5 23 GPIO_ACTIVE_HIGH>; /* 151 */
1102
1103         modem: hsi-client {
1104                 compatible = "nokia,n900-modem";
1105
1106                 pinctrl-names = "default";
1107                 pinctrl-0 = <&modem_pins>;
1108
1109                 hsi-channel-ids = <0>, <1>, <2>, <3>;
1110                 hsi-channel-names = "mcsaab-control",
1111                                     "speech-control",
1112                                     "speech-data",
1113                                     "mcsaab-data";
1114                 hsi-speed-kbps = <55000>;
1115                 hsi-mode = "frame";
1116                 hsi-flow = "synchronized";
1117                 hsi-arb-mode = "round-robin";
1118
1119                 interrupts-extended = <&gpio3 8 IRQ_TYPE_EDGE_FALLING>; /* 72 */
1120
1121                 gpios = <&gpio3  6 GPIO_ACTIVE_HIGH>, /* 70 */
1122                         <&gpio3  9 GPIO_ACTIVE_HIGH>, /* 73 */
1123                         <&gpio3 10 GPIO_ACTIVE_HIGH>, /* 74 */
1124                         <&gpio3 11 GPIO_ACTIVE_HIGH>, /* 75 */
1125                         <&gpio5 29 GPIO_ACTIVE_HIGH>; /* 157 */
1126                 gpio-names = "cmt_apeslpx",
1127                              "cmt_rst_rq",
1128                              "cmt_en",
1129                              "cmt_rst",
1130                              "cmt_bsi";
1131         };
1132 };
1133
1134 &ssi_port2 {
1135         status = "disabled";
1136 };