arch/arm/boot/dts/logicpd-torpedo-som.dtsi

   1 /*
   2  * This program is free software; you can redistribute it and/or modify
   3  * it under the terms of the GNU General Public License version 2 as
   4  * published by the Free Software Foundation.
   5  */
   6
   7 #include <dt-bindings/input/input.h>
   8
   9 / {
  10         cpus {
  11                 cpu@0 {
  12                         cpu0-supply = <&vcc>;
  13                 };
  14         };
  15
  16         leds {
  17                 compatible = "gpio-leds";
  18                 user0 {
  19                         label = "user0";
  20                         gpios = <&twl_gpio 18 GPIO_ACTIVE_LOW>; /* LEDA */
  21                         linux,default-trigger = "none";
  22                 };
  23         };
  24
  25         wl12xx_vmmc: wl12xx_vmmc {
  26                 compatible = "regulator-fixed";
  27                 regulator-name = "vwl1271";
  28                 regulator-min-microvolt = <1800000>;
  29                 regulator-max-microvolt = <1800000>;
  30                 gpio = <&gpio5 29 0>;   /* gpio157 */
  31                 startup-delay-us = <70000>;
  32                 enable-active-high;
  33                 vin-supply = <&vmmc2>;
  34         };
  35 };
  36
  37 &gpmc {
  38         ranges = <0 0 0x00000000 0x1000000>;    /* CS0: 16MB for NAND */
  39
  40         nand@0,0 {
  41                 linux,mtd-name = "micron,mt29f4g16abbda3w";
  42                 reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
  43                 nand-bus-width = <16>;
  44                 ti,nand-ecc-opt = "bch8";
  45                 gpmc,sync-clk-ps = <0>;
  46                 gpmc,cs-on-ns = <0>;
  47                 gpmc,cs-rd-off-ns = <44>;
  48                 gpmc,cs-wr-off-ns = <44>;
  49                 gpmc,adv-on-ns = <6>;
  50                 gpmc,adv-rd-off-ns = <34>;
  51                 gpmc,adv-wr-off-ns = <44>;
  52                 gpmc,we-off-ns = <40>;
  53                 gpmc,oe-off-ns = <54>;
  54                 gpmc,access-ns = <64>;
  55                 gpmc,rd-cycle-ns = <82>;
  56                 gpmc,wr-cycle-ns = <82>;
  57                 gpmc,wr-access-ns = <40>;
  58                 gpmc,wr-data-mux-bus-ns = <0>;
  59                 gpmc,device-width = <2>;
  60                 #address-cells = <1>;
  61                 #size-cells = <1>;
  62
  63                 /* u-boot uses mtdparts=omap2-nand.0:512k(x-loader),1920k(u-boot),128k(u-boot-env),4m(kernel),-(fs) */
  64
  65                 x-loader@0 {
  66                         label = "x-loader";
  67                         reg = <0 0x80000>;
  68                 };
  69
  70                 bootloaders@80000 {
  71                         label = "u-boot";
  72                         reg = <0x80000 0x1e0000>;
  73                 };
  74
  75                 bootloaders_env@260000 {
  76                         label = "u-boot-env";
  77                         reg = <0x260000 0x20000>;
  78                 };
  79
  80                 kernel@280000 {
  81                         label = "kernel";
  82                         reg = <0x280000 0x400000>;
  83                 };
  84
  85                 filesystem@680000 {
  86                         label = "fs";
  87                         reg = <0x680000 0>;     /* 0 = MTDPART_SIZ_FULL */
  88                 };
  89         };
  90 };
  91
  92 &i2c1 {
  93         clock-frequency = <2600000>;
  94
  95         twl: twl@48 {
  96                 reg = <0x48>;
  97                 interrupts = <7>; /* SYS_NIRQ cascaded to intc */
  98                 interrupt-parent = <&intc>;
  99                 twl_audio: audio {
 100                         compatible = "ti,twl4030-audio";
 101                         codec {
 102                         };
 103                 };
 104         };
 105 };
 106
 107 &i2c2 {
 108         clock-frequency = <400000>;
 109 };
 110
 111 &i2c3 {
 112         clock-frequency = <400000>;
 113 };
 114
 115 /*
 116  * Only found on the wireless SOM. For the SOM without wireless, the pins for
 117  * MMC3 can be routed with jumpers to the second MMC slot on the devkit and
 118  * gpio157 is not connected. So this should be OK to keep common for now,
 119  * probably device tree overlays is the way to go with the various SOM and
 120  * jumpering combinations for the long run.
 121  */
 122 &mmc3 {
 123         interrupts-extended = <&intc 94 &omap3_pmx_core2 0x46>;
 124         pinctrl-0 = <&mmc3_pins &mmc3_core2_pins>;
 125         pinctrl-names = "default";
 126         vmmc-supply = <&wl12xx_vmmc>;
 127         non-removable;
 128         bus-width = <4>;
 129         cap-power-off-card;
 130         #address-cells = <1>;
 131         #size-cells = <0>;
 132         wlcore: wlcore@2 {
 133                 compatible = "ti,wl1283";
 134                 reg = <2>;
 135                 interrupt-parent = <&gpio5>;
 136                 interrupts = <24 IRQ_TYPE_LEVEL_HIGH>; /* gpio 152 */
 137                 ref-clock-frequency = <26000000>;
 138                 tcxo-clock-frequency = <26000000>;
 139         };
 140 };
 141
 142 &omap3_pmx_core {
 143         mmc3_pins: pinmux_mm3_pins {
 144                 pinctrl-single,pins = <
 145                         OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat4.sdmmc3_dat0 */
 146                         OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat5.sdmmc3_dat1 */
 147                         OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat2 */
 148                         OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat3 */
 149                         OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4) /* mcbsp4_clkx.gpio_152 */
 150                         OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4)       /* mcbsp1_fsr.gpio_157 */
 151                 >;
 152         };
 153         mcbsp2_pins: pinmux_mcbsp2_pins {
 154                 pinctrl-single,pins = <
 155                         OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT | MUX_MODE0)        /* mcbsp2_fsx */
 156                         OMAP3_CORE1_IOPAD(0x213e, PIN_INPUT | MUX_MODE0)        /* mcbsp2_clkx */
 157                         OMAP3_CORE1_IOPAD(0x2140, PIN_INPUT | MUX_MODE0)        /* mcbsp2_dr */
 158                         OMAP3_CORE1_IOPAD(0x2142, PIN_OUTPUT | MUX_MODE0)       /* mcbsp2_dx */
 159                 >;
 160         };
 161         uart2_pins: pinmux_uart2_pins {
 162                 pinctrl-single,pins = <
 163                         OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT | MUX_MODE0)        /* uart2_cts.uart2_cts */
 164                         OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0)       /* uart2_rts .uart2_rts*/
 165                         OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0)       /* uart2_tx.uart2_tx */
 166                         OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0)        /* uart2_rx.uart2_rx */
 167                         OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT | MUX_MODE4)       /* GPIO_162,BT_EN */
 168                 >;
 169         };
 170 };
 171
 172 &uart2 {
 173         interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>;
 174         pinctrl-names = "default";
 175         pinctrl-0 = <&uart2_pins>;
 176 };
 177
 178 &omap3_pmx_core2 {
 179         mmc3_core2_pins: pinmux_mmc3_core2_pins {
 180                 pinctrl-single,pins = <
 181                         OMAP3630_CORE2_IOPAD(0x25d8, PIN_INPUT_PULLUP | MUX_MODE2)   /* etk_clk.sdmmc3_clk */
 182                         OMAP3630_CORE2_IOPAD(0x25da, PIN_INPUT_PULLUP | MUX_MODE2)   /* etk_ctl.sdmmc3_cmd */
 183                 >;
 184         };
 185 };
 186
 187 #include "twl4030.dtsi"
 188 #include "twl4030_omap3.dtsi"
 189
 190 &twl {
 191         twl_power: power {
 192                 compatible = "ti,twl4030-power-idle-osc-off", "ti,twl4030-power-idle";
 193                 ti,use_poweroff;
 194         };
 195 };
 196
 197 &twl_gpio {
 198         ti,use-leds;
 199 };