arch/arm/boot/dts/exynos4412-midas.dtsi

   1 // SPDX-License-Identifier: GPL-2.0
   2 /*
   3  * Samsung's Exynos4412 based Trats 2 board device tree source
   4  *
   5  * Copyright (c) 2013 Samsung Electronics Co., Ltd.
   6  *              http://www.samsung.com
   7  *
   8  * Device tree source file for Samsung's Trats 2 board which is based on
   9  * Samsung's Exynos4412 SoC.
  10  */
  11
  12 /dts-v1/;
  13 #include "exynos4412.dtsi"
  14 #include "exynos4412-ppmu-common.dtsi"
  15 #include <dt-bindings/gpio/gpio.h>
  16 #include <dt-bindings/interrupt-controller/irq.h>
  17 #include <dt-bindings/clock/maxim,max77686.h>
  18 #include <dt-bindings/pinctrl/samsung.h>
  19
  20 / {
  21         compatible = "samsung,midas", "samsung,exynos4412", "samsung,exynos4";
  22
  23         aliases {
  24                 i2c11 = &i2c_max77693;
  25                 i2c12 = &i2c_max77693_fuel;
  26         };
  27
  28         chosen {
  29                 stdout-path = &serial_2;
  30         };
  31
  32         firmware@204f000 {
  33                 compatible = "samsung,secure-firmware";
  34                 reg = <0x0204F000 0x1000>;
  35         };
  36
  37         fixed-rate-clocks {
  38                 xxti {
  39                         compatible = "samsung,clock-xxti", "fixed-clock";
  40                         clock-frequency = <0>;
  41                 };
  42
  43                 xusbxti {
  44                         compatible = "samsung,clock-xusbxti", "fixed-clock";
  45                         clock-frequency = <24000000>;
  46                 };
  47         };
  48
  49         regulators {
  50                 compatible = "simple-bus";
  51                 #address-cells = <1>;
  52                 #size-cells = <0>;
  53
  54                 cam_io_reg: voltage-regulator-1 {
  55                         compatible = "regulator-fixed";
  56                         regulator-name = "CAM_SENSOR_A";
  57                         regulator-min-microvolt = <2800000>;
  58                         regulator-max-microvolt = <2800000>;
  59                         enable-active-high;
  60                         status = "disabled";
  61                 };
  62
  63                 cam_af_reg: voltage-regulator-3 {
  64                         compatible = "regulator-fixed";
  65                         regulator-name = "CAM_AF";
  66                         regulator-min-microvolt = <2800000>;
  67                         regulator-max-microvolt = <2800000>;
  68                         enable-active-high;
  69                         status = "disabled";
  70                 };
  71
  72                 vsil12: voltage-regulator-6 {
  73                         compatible = "regulator-fixed";
  74                         regulator-name = "VSIL_1.2V";
  75                         regulator-min-microvolt = <1200000>;
  76                         regulator-max-microvolt = <1200000>;
  77                         gpio = <&gpl0 4 GPIO_ACTIVE_HIGH>;
  78                         enable-active-high;
  79                         vin-supply = <&buck7_reg>;
  80                 };
  81
  82                 vcc33mhl: voltage-regulator-7 {
  83                         compatible = "regulator-fixed";
  84                         regulator-name = "VCC_3.3_MHL";
  85                         regulator-min-microvolt = <3300000>;
  86                         regulator-max-microvolt = <3300000>;
  87                         gpio = <&gpl0 4 GPIO_ACTIVE_HIGH>;
  88                         enable-active-high;
  89                 };
  90
  91                 vcc18mhl: voltage-regulator-8 {
  92                         compatible = "regulator-fixed";
  93                         regulator-name = "VCC_1.8_MHL";
  94                         regulator-min-microvolt = <1800000>;
  95                         regulator-max-microvolt = <1800000>;
  96                         gpio = <&gpl0 4 GPIO_ACTIVE_HIGH>;
  97                         enable-active-high;
  98                 };
  99         };
 100
 101         gpio-keys {
 102                 compatible = "gpio-keys";
 103
 104                 key-down {
 105                         gpios = <&gpx3 3 GPIO_ACTIVE_LOW>;
 106                         linux,code = <114>;
 107                         label = "volume down";
 108                         debounce-interval = <10>;
 109                 };
 110
 111                 key-up {
 112                         gpios = <&gpx2 2 GPIO_ACTIVE_LOW>;
 113                         linux,code = <115>;
 114                         label = "volume up";
 115                         debounce-interval = <10>;
 116                 };
 117
 118                 key-power {
 119                         gpios = <&gpx2 7 GPIO_ACTIVE_LOW>;
 120                         linux,code = <116>;
 121                         label = "power";
 122                         debounce-interval = <10>;
 123                         wakeup-source;
 124                 };
 125
 126                 key-ok {
 127                         gpios = <&gpx0 1 GPIO_ACTIVE_LOW>;
 128                         linux,code = <139>;
 129                         label = "ok";
 130                         debounce-interval = <10>;
 131                         wakeup-source;
 132                 };
 133         };
 134
 135         i2c_max77693: i2c-gpio-1 {
 136                 compatible = "i2c-gpio";
 137                 gpios = <&gpm2 0 GPIO_ACTIVE_HIGH>, <&gpm2 1 GPIO_ACTIVE_HIGH>;
 138                 i2c-gpio,delay-us = <2>;
 139                 #address-cells = <1>;
 140                 #size-cells = <0>;
 141                 status = "okay";
 142
 143                 max77693@66 {
 144                         compatible = "maxim,max77693";
 145                         interrupt-parent = <&gpx1>;
 146                         interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
 147                         reg = <0x66>;
 148
 149                         regulators {
 150                                 esafeout1_reg: ESAFEOUT1 {
 151                                         regulator-name = "ESAFEOUT1";
 152                                 };
 153                                 esafeout2_reg: ESAFEOUT2 {
 154                                         regulator-name = "ESAFEOUT2";
 155                                 };
 156                                 charger_reg: CHARGER {
 157                                         regulator-name = "CHARGER";
 158                                         regulator-min-microamp = <60000>;
 159                                         regulator-max-microamp = <2580000>;
 160                                 };
 161                         };
 162
 163                         max77693_haptic {
 164                                 compatible = "maxim,max77693-haptic";
 165                                 haptic-supply = <&ldo26_reg>;
 166                                 pwms = <&pwm 0 38022 0>;
 167                         };
 168
 169                         charger {
 170                                 compatible = "maxim,max77693-charger";
 171
 172                                 maxim,constant-microvolt = <4350000>;
 173                                 maxim,min-system-microvolt = <3600000>;
 174                                 maxim,thermal-regulation-celsius = <100>;
 175                                 maxim,battery-overcurrent-microamp = <3500000>;
 176                                 maxim,charge-input-threshold-microvolt = <4300000>;
 177                         };
 178                 };
 179         };
 180
 181         i2c_max77693_fuel: i2c-gpio-3 {
 182                 compatible = "i2c-gpio";
 183                 gpios = <&gpf1 5 GPIO_ACTIVE_HIGH>, <&gpf1 4 GPIO_ACTIVE_HIGH>;
 184                 i2c-gpio,delay-us = <2>;
 185                 #address-cells = <1>;
 186                 #size-cells = <0>;
 187                 status = "okay";
 188
 189                 max77693-fuel-gauge@36 {
 190                         compatible = "maxim,max17047";
 191                         interrupt-parent = <&gpx2>;
 192                         interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
 193                         reg = <0x36>;
 194
 195                         maxim,over-heat-temp = <700>;
 196                         maxim,over-volt = <4500>;
 197                 };
 198         };
 199
 200         i2c-mhl {
 201                 compatible = "i2c-gpio";
 202                 gpios = <&gpf0 4 GPIO_ACTIVE_HIGH>, <&gpf0 6 GPIO_ACTIVE_HIGH>;
 203                 i2c-gpio,delay-us = <100>;
 204                 #address-cells = <1>;
 205                 #size-cells = <0>;
 206
 207                 pinctrl-0 = <&i2c_mhl_bus>;
 208                 pinctrl-names = "default";
 209                 status = "okay";
 210
 211                 sii9234: hdmi-bridge@39 {
 212                         compatible = "sil,sii9234";
 213                         avcc33-supply = <&vcc33mhl>;
 214                         iovcc18-supply = <&vcc18mhl>;
 215                         avcc12-supply = <&vsil12>;
 216                         cvcc12-supply = <&vsil12>;
 217                         reset-gpios = <&gpf3 4 GPIO_ACTIVE_LOW>;
 218                         interrupt-parent = <&gpf3>;
 219                         interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
 220                         reg = <0x39>;
 221
 222                         port {
 223                                 mhl_to_hdmi: endpoint {
 224                                         remote-endpoint = <&hdmi_to_mhl>;
 225                                 };
 226                         };
 227                 };
 228         };
 229
 230         wlan_pwrseq: sdhci3-pwrseq {
 231                 compatible = "mmc-pwrseq-simple";
 232                 reset-gpios = <&gpj0 0 GPIO_ACTIVE_LOW>;
 233                 clocks = <&max77686 MAX77686_CLK_PMIC>;
 234                 clock-names = "ext_clock";
 235         };
 236
 237         sound {
 238                 compatible = "samsung,trats2-audio";
 239                 samsung,i2s-controller = <&i2s0>;
 240                 samsung,model = "Trats2";
 241                 samsung,audio-codec = <&wm1811>;
 242                 samsung,audio-routing =
 243                         "SPK", "SPKOUTLN",
 244                         "SPK", "SPKOUTLP",
 245                         "SPK", "SPKOUTRN",
 246                         "SPK", "SPKOUTRP";
 247         };
 248
 249         thermistor-ap {
 250                 compatible = "murata,ncp15wb473";
 251                 pullup-uv = <1800000>;   /* VCC_1.8V_AP */
 252                 pullup-ohm = <100000>;   /* 100K */
 253                 pulldown-ohm = <100000>; /* 100K */
 254                 io-channels = <&adc 1>;  /* AP temperature */
 255         };
 256
 257         thermistor-battery {
 258                 compatible = "murata,ncp15wb473";
 259                 pullup-uv = <1800000>;   /* VCC_1.8V_AP */
 260                 pullup-ohm = <100000>;   /* 100K */
 261                 pulldown-ohm = <100000>; /* 100K */
 262                 io-channels = <&adc 2>;  /* Battery temperature */
 263         };
 264
 265         thermal-zones {
 266                 cpu_thermal: cpu-thermal {
 267                         cooling-maps {
 268                                 map0 {
 269                                      /* Corresponds to 800MHz at freq_table */
 270                                      cooling-device = <&cpu0 7 7>;
 271                                 };
 272                                 map1 {
 273                                      /* Corresponds to 200MHz at freq_table */
 274                                      cooling-device = <&cpu0 13 13>;
 275                                };
 276                        };
 277                 };
 278         };
 279 };
 280
 281 &adc {
 282         vdd-supply = <&ldo3_reg>;
 283         status = "okay";
 284 };
 285
 286 &bus_dmc {
 287         devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>;
 288         vdd-supply = <&buck1_reg>;
 289         status = "okay";
 290 };
 291
 292 &bus_acp {
 293         devfreq = <&bus_dmc>;
 294         status = "okay";
 295 };
 296
 297 &bus_c2c {
 298         devfreq = <&bus_dmc>;
 299         status = "okay";
 300 };
 301
 302 &bus_leftbus {
 303         devfreq-events = <&ppmu_leftbus_3>, <&ppmu_rightbus_3>;
 304         vdd-supply = <&buck3_reg>;
 305         status = "okay";
 306 };
 307
 308 &bus_rightbus {
 309         devfreq = <&bus_leftbus>;
 310         status = "okay";
 311 };
 312
 313 &bus_display {
 314         devfreq = <&bus_leftbus>;
 315         status = "okay";
 316 };
 317
 318 &bus_fsys {
 319         devfreq = <&bus_leftbus>;
 320         status = "okay";
 321 };
 322
 323 &bus_peri {
 324         devfreq = <&bus_leftbus>;
 325         status = "okay";
 326 };
 327
 328 &bus_mfc {
 329         devfreq = <&bus_leftbus>;
 330         status = "okay";
 331 };
 332
 333 &camera {
 334         pinctrl-0 = <&cam_port_a_clk_active &cam_port_b_clk_active>;
 335         pinctrl-names = "default";
 336         status = "okay";
 337         assigned-clocks = <&clock CLK_MOUT_CAM0>,
 338                 <&clock CLK_MOUT_CAM1>;
 339         assigned-clock-parents = <&clock CLK_XUSBXTI>,
 340                 <&clock CLK_XUSBXTI>;
 341 };
 342
 343 &cpu0 {
 344         cpu0-supply = <&buck2_reg>;
 345 };
 346
 347 &csis_0 {
 348         status = "okay";
 349         vddcore-supply = <&ldo8_reg>;
 350         vddio-supply = <&ldo10_reg>;
 351         assigned-clocks = <&clock CLK_MOUT_CSIS0>,
 352                         <&clock CLK_SCLK_CSIS0>;
 353         assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
 354         assigned-clock-rates = <0>, <176000000>;
 355
 356         /* Camera C (3) MIPI CSI-2 (CSIS0) */
 357         port@3 {
 358                 reg = <3>;
 359                 csis0_ep: endpoint {
 360                         remote-endpoint = <&s5c73m3_ep>;
 361                         data-lanes = <1 2 3 4>;
 362                         samsung,csis-hs-settle = <12>;
 363                 };
 364         };
 365 };
 366
 367 &csis_1 {
 368         status = "okay";
 369         vddcore-supply = <&ldo8_reg>;
 370         vddio-supply = <&ldo10_reg>;
 371         assigned-clocks = <&clock CLK_MOUT_CSIS1>,
 372                         <&clock CLK_SCLK_CSIS1>;
 373         assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
 374         assigned-clock-rates = <0>, <176000000>;
 375
 376         /* Camera D (4) MIPI CSI-2 (CSIS1) */
 377         port@4 {
 378                 reg = <4>;
 379                 csis1_ep: endpoint {
 380                         remote-endpoint = <&is_s5k6a3_ep>;
 381                         data-lanes = <1>;
 382                         samsung,csis-hs-settle = <18>;
 383                         samsung,csis-wclk;
 384                 };
 385         };
 386 };
 387
 388 &dsi_0 {
 389         vddcore-supply = <&ldo8_reg>;
 390         vddio-supply = <&ldo10_reg>;
 391         samsung,burst-clock-frequency = <500000000>;
 392         samsung,esc-clock-frequency = <20000000>;
 393         samsung,pll-clock-frequency = <24000000>;
 394 };
 395
 396 &exynos_usbphy {
 397         vbus-supply = <&esafeout1_reg>;
 398         status = "okay";
 399 };
 400
 401 &fimc_0 {
 402         status = "okay";
 403         assigned-clocks = <&clock CLK_MOUT_FIMC0>,
 404                         <&clock CLK_SCLK_FIMC0>;
 405         assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
 406         assigned-clock-rates = <0>, <176000000>;
 407 };
 408
 409 &fimc_1 {
 410         status = "okay";
 411         assigned-clocks = <&clock CLK_MOUT_FIMC1>,
 412                         <&clock CLK_SCLK_FIMC1>;
 413         assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
 414         assigned-clock-rates = <0>, <176000000>;
 415 };
 416
 417 &fimc_2 {
 418         status = "okay";
 419         assigned-clocks = <&clock CLK_MOUT_FIMC2>,
 420                         <&clock CLK_SCLK_FIMC2>;
 421         assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
 422         assigned-clock-rates = <0>, <176000000>;
 423 };
 424
 425 &fimc_3 {
 426         status = "okay";
 427         assigned-clocks = <&clock CLK_MOUT_FIMC3>,
 428                         <&clock CLK_SCLK_FIMC3>;
 429         assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
 430         assigned-clock-rates = <0>, <176000000>;
 431 };
 432
 433 &fimc_is {
 434         pinctrl-0 = <&fimc_is_uart>;
 435         pinctrl-names = "default";
 436         status = "okay";
 437
 438         };
 439
 440 &fimc_lite_0 {
 441         status = "okay";
 442 };
 443
 444 &fimc_lite_1 {
 445         status = "okay";
 446 };
 447
 448 &fimd {
 449         status = "okay";
 450 };
 451
 452 &hdmi {
 453         hpd-gpios = <&gpx3 7 GPIO_ACTIVE_HIGH>;
 454         pinctrl-names = "default";
 455         pinctrl-0 = <&hdmi_hpd>;
 456         vdd-supply = <&ldo3_reg>;
 457         vdd_osc-supply = <&ldo4_reg>;
 458         vdd_pll-supply = <&ldo3_reg>;
 459         ddc = <&i2c_5>;
 460         status = "okay";
 461
 462         ports {
 463                 #address-cells = <1>;
 464                 #size-cells = <0>;
 465
 466                 port@1 {
 467                         reg = <1>;
 468                         hdmi_to_mhl: endpoint {
 469                                 remote-endpoint = <&mhl_to_hdmi>;
 470                         };
 471                 };
 472         };
 473 };
 474
 475 &hsotg {
 476         vusb_d-supply = <&ldo15_reg>;
 477         vusb_a-supply = <&ldo12_reg>;
 478         dr_mode = "peripheral";
 479         status = "okay";
 480 };
 481
 482 &i2c_0 {
 483         samsung,i2c-sda-delay = <100>;
 484         samsung,i2c-slave-addr = <0x10>;
 485         samsung,i2c-max-bus-freq = <400000>;
 486         pinctrl-0 = <&i2c0_bus>;
 487         pinctrl-names = "default";
 488         status = "okay";
 489
 490         s5c73m3: s5c73m3@3c {
 491                 compatible = "samsung,s5c73m3";
 492                 reg = <0x3c>;
 493                 xshutdown-gpios = <&gpf1 3 GPIO_ACTIVE_LOW>; /* ISP_RESET */
 494                 vdd-int-supply = <&buck9_reg>;
 495                 vddio-cis-supply = <&ldo9_reg>;
 496                 vddio-host-supply = <&ldo18_reg>;
 497                 vdd-af-supply = <&cam_af_reg>;
 498                 vdd-reg-supply = <&cam_io_reg>;
 499                 clock-frequency = <24000000>;
 500                 /* CAM_A_CLKOUT */
 501                 clocks = <&camera 0>;
 502                 clock-names = "cis_extclk";
 503                 status = "disabled";
 504                 port {
 505                         s5c73m3_ep: endpoint {
 506                                 remote-endpoint = <&csis0_ep>;
 507                                 data-lanes = <1 2 3 4>;
 508                         };
 509                 };
 510         };
 511 };
 512
 513 &i2c1_isp {
 514         pinctrl-0 = <&fimc_is_i2c1>;
 515         pinctrl-names = "default";
 516
 517         s5k6a3@10 {
 518                 compatible = "samsung,s5k6a3";
 519                 reg = <0x10>;
 520                 svdda-supply = <&cam_io_reg>;
 521                 svddio-supply = <&ldo19_reg>;
 522                 afvdd-supply = <&ldo19_reg>;
 523                 clock-frequency = <24000000>;
 524                 /* CAM_B_CLKOUT */
 525                 clocks = <&camera 1>;
 526                 clock-names = "extclk";
 527                 samsung,camclk-out = <1>;
 528                 gpios = <&gpm1 6 GPIO_ACTIVE_HIGH>;
 529
 530                 port {
 531                         is_s5k6a3_ep: endpoint {
 532                                 remote-endpoint = <&csis1_ep>;
 533                                 data-lanes = <1>;
 534                         };
 535                 };
 536         };
 537 };
 538
 539 &i2c_3 {
 540         samsung,i2c-sda-delay = <100>;
 541         samsung,i2c-slave-addr = <0x10>;
 542         samsung,i2c-max-bus-freq = <400000>;
 543         pinctrl-0 = <&i2c3_bus>;
 544         pinctrl-names = "default";
 545         status = "okay";
 546 };
 547
 548 &i2c_4 {
 549         samsung,i2c-sda-delay = <100>;
 550         samsung,i2c-slave-addr = <0x10>;
 551         samsung,i2c-max-bus-freq = <100000>;
 552         pinctrl-0 = <&i2c4_bus>;
 553         pinctrl-names = "default";
 554         status = "okay";
 555
 556         wm1811: wm1811@1a {
 557                 compatible = "wlf,wm1811";
 558                 reg = <0x1a>;
 559                 clocks = <&pmu_system_controller 0>;
 560                 clock-names = "MCLK1";
 561                 DCVDD-supply = <&ldo3_reg>;
 562                 DBVDD1-supply = <&ldo3_reg>;
 563                 wlf,ldo1ena = <&gpj0 4 0>;
 564         };
 565 };
 566
 567 &i2c_5 {
 568         status = "okay";
 569 };
 570
 571 &i2c_7 {
 572         samsung,i2c-sda-delay = <100>;
 573         samsung,i2c-slave-addr = <0x10>;
 574         samsung,i2c-max-bus-freq = <100000>;
 575         pinctrl-0 = <&i2c7_bus>;
 576         pinctrl-names = "default";
 577         status = "okay";
 578
 579         max77686: max77686_pmic@9 {
 580                 compatible = "maxim,max77686";
 581                 interrupt-parent = <&gpx0>;
 582                 interrupts = <7 IRQ_TYPE_NONE>;
 583                 reg = <0x09>;
 584                 #clock-cells = <1>;
 585
 586                 voltage-regulators {
 587                         ldo1_reg: LDO1 {
 588                                 regulator-name = "VALIVE_1.0V_AP";
 589                                 regulator-min-microvolt = <1000000>;
 590                                 regulator-max-microvolt = <1000000>;
 591                                 regulator-always-on;
 592                         };
 593
 594                         ldo2_reg: LDO2 {
 595                                 regulator-name = "VM1M2_1.2V_AP";
 596                                 regulator-min-microvolt = <1200000>;
 597                                 regulator-max-microvolt = <1200000>;
 598                                 regulator-always-on;
 599                                 regulator-state-mem {
 600                                         regulator-on-in-suspend;
 601                                 };
 602                         };
 603
 604                         ldo3_reg: LDO3 {
 605                                 regulator-name = "VCC_1.8V_AP";
 606                                 regulator-min-microvolt = <1800000>;
 607                                 regulator-max-microvolt = <1800000>;
 608                                 regulator-always-on;
 609                         };
 610
 611                         ldo4_reg: LDO4 {
 612                                 regulator-name = "VCC_2.8V_AP";
 613                                 regulator-min-microvolt = <2800000>;
 614                                 regulator-max-microvolt = <2800000>;
 615                                 regulator-always-on;
 616                         };
 617
 618                         ldo5_reg: LDO5 {
 619                                 regulator-name = "VCC_1.8V_IO";
 620                                 regulator-min-microvolt = <1800000>;
 621                                 regulator-max-microvolt = <1800000>;
 622                                 regulator-always-on;
 623                         };
 624
 625                         ldo6_reg: LDO6 {
 626                                 regulator-name = "VMPLL_1.0V_AP";
 627                                 regulator-min-microvolt = <1000000>;
 628                                 regulator-max-microvolt = <1000000>;
 629                                 regulator-always-on;
 630                                 regulator-state-mem {
 631                                         regulator-on-in-suspend;
 632                                 };
 633                         };
 634
 635                         ldo7_reg: LDO7 {
 636                                 regulator-name = "VPLL_1.0V_AP";
 637                                 regulator-min-microvolt = <1000000>;
 638                                 regulator-max-microvolt = <1000000>;
 639                                 regulator-always-on;
 640                                 regulator-state-mem {
 641                                         regulator-on-in-suspend;
 642                                 };
 643                         };
 644
 645                         ldo8_reg: LDO8 {
 646                                 regulator-name = "VMIPI_1.0V";
 647                                 regulator-min-microvolt = <1000000>;
 648                                 regulator-max-microvolt = <1000000>;
 649                                 regulator-state-mem {
 650                                         regulator-off-in-suspend;
 651                                 };
 652                         };
 653
 654                         ldo9_reg: LDO9 {
 655                                 regulator-name = "CAM_ISP_MIPI_1.2V";
 656                                 regulator-min-microvolt = <1200000>;
 657                                 regulator-max-microvolt = <1200000>;
 658                         };
 659
 660                         ldo10_reg: LDO10 {
 661                                 regulator-name = "VMIPI_1.8V";
 662                                 regulator-min-microvolt = <1800000>;
 663                                 regulator-max-microvolt = <1800000>;
 664                                 regulator-state-mem {
 665                                         regulator-off-in-suspend;
 666                                 };
 667                         };
 668
 669                         ldo11_reg: LDO11 {
 670                                 regulator-name = "VABB1_1.95V";
 671                                 regulator-min-microvolt = <1950000>;
 672                                 regulator-max-microvolt = <1950000>;
 673                                 regulator-always-on;
 674                                 regulator-state-mem {
 675                                         regulator-off-in-suspend;
 676                                 };
 677                         };
 678
 679                         ldo12_reg: LDO12 {
 680                                 regulator-name = "VUOTG_3.0V";
 681                                 regulator-min-microvolt = <3000000>;
 682                                 regulator-max-microvolt = <3000000>;
 683                                 regulator-state-mem {
 684                                         regulator-off-in-suspend;
 685                                 };
 686                         };
 687
 688                         ldo13_reg: LDO13 {
 689                                 regulator-name = "NFC_AVDD_1.8V";
 690                                 regulator-min-microvolt = <1800000>;
 691                                 regulator-max-microvolt = <1800000>;
 692                         };
 693
 694                         ldo14_reg: LDO14 {
 695                                 regulator-name = "VABB2_1.95V";
 696                                 regulator-min-microvolt = <1950000>;
 697                                 regulator-max-microvolt = <1950000>;
 698                                 regulator-always-on;
 699                                 regulator-state-mem {
 700                                         regulator-off-in-suspend;
 701                                 };
 702                         };
 703
 704                         ldo15_reg: LDO15 {
 705                                 regulator-name = "VHSIC_1.0V";
 706                                 regulator-min-microvolt = <1000000>;
 707                                 regulator-max-microvolt = <1000000>;
 708                                 regulator-state-mem {
 709                                         regulator-on-in-suspend;
 710                                 };
 711                         };
 712
 713                         ldo16_reg: LDO16 {
 714                                 regulator-name = "VHSIC_1.8V";
 715                                 regulator-min-microvolt = <1800000>;
 716                                 regulator-max-microvolt = <1800000>;
 717                                 regulator-state-mem {
 718                                         regulator-on-in-suspend;
 719                                 };
 720                         };
 721
 722                         ldo17_reg: LDO17 {
 723                                 regulator-name = "CAM_SENSOR_CORE_1.2V";
 724                                 regulator-min-microvolt = <1200000>;
 725                                 regulator-max-microvolt = <1200000>;
 726                         };
 727
 728                         ldo18_reg: LDO18 {
 729                                 regulator-name = "CAM_ISP_SEN_IO_1.8V";
 730                                 regulator-min-microvolt = <1800000>;
 731                                 regulator-max-microvolt = <1800000>;
 732                         };
 733
 734                         ldo19_reg: LDO19 {
 735                                 regulator-name = "VT_CAM_1.8V";
 736                                 regulator-min-microvolt = <1800000>;
 737                                 regulator-max-microvolt = <1800000>;
 738                         };
 739
 740                         ldo20_reg: LDO20 {
 741                                 regulator-name = "VDDQ_PRE_1.8V";
 742                                 regulator-min-microvolt = <1800000>;
 743                                 regulator-max-microvolt = <1800000>;
 744                         };
 745
 746                         ldo21_reg: LDO21 {
 747                                 regulator-name = "VTF_2.8V";
 748                                 regulator-min-microvolt = <2800000>;
 749                                 regulator-max-microvolt = <2800000>;
 750                                 maxim,ena-gpios = <&gpy2 0 GPIO_ACTIVE_HIGH>;
 751                         };
 752
 753                         ldo22_reg: LDO22 {
 754                                 regulator-name = "VMEM_VDD_2.8V";
 755                                 regulator-min-microvolt = <2800000>;
 756                                 regulator-max-microvolt = <2800000>;
 757                                 maxim,ena-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>;
 758                         };
 759
 760                         ldo23_reg: LDO23 {
 761                                 regulator-name = "TSP_AVDD_3.3V";
 762                                 regulator-min-microvolt = <3300000>;
 763                                 regulator-max-microvolt = <3300000>;
 764                         };
 765
 766                         ldo24_reg: LDO24 {
 767                                 regulator-name = "TSP_VDD_1.8V";
 768                                 regulator-min-microvolt = <1800000>;
 769                                 regulator-max-microvolt = <1800000>;
 770                         };
 771
 772                         ldo25_reg: LDO25 {
 773                                 regulator-name = "LDO25";
 774                         };
 775
 776                         ldo26_reg: LDO26 {
 777                                 regulator-name = "MOTOR_VCC_3.0V";
 778                                 regulator-min-microvolt = <3000000>;
 779                                 regulator-max-microvolt = <3000000>;
 780                         };
 781
 782                         buck1_reg: BUCK1 {
 783                                 regulator-name = "vdd_mif";
 784                                 regulator-min-microvolt = <850000>;
 785                                 regulator-max-microvolt = <1100000>;
 786                                 regulator-always-on;
 787                                 regulator-boot-on;
 788                                 regulator-state-mem {
 789                                         regulator-off-in-suspend;
 790                                 };
 791                         };
 792
 793                         buck2_reg: BUCK2 {
 794                                 regulator-name = "vdd_arm";
 795                                 regulator-min-microvolt = <850000>;
 796                                 regulator-max-microvolt = <1500000>;
 797                                 regulator-always-on;
 798                                 regulator-boot-on;
 799                                 regulator-state-mem {
 800                                         regulator-on-in-suspend;
 801                                 };
 802                         };
 803
 804                         buck3_reg: BUCK3 {
 805                                 regulator-name = "vdd_int";
 806                                 regulator-min-microvolt = <850000>;
 807                                 regulator-max-microvolt = <1150000>;
 808                                 regulator-always-on;
 809                                 regulator-boot-on;
 810                                 regulator-state-mem {
 811                                         regulator-off-in-suspend;
 812                                 };
 813                         };
 814
 815                         buck4_reg: BUCK4 {
 816                                 regulator-name = "vdd_g3d";
 817                                 regulator-min-microvolt = <850000>;
 818                                 regulator-max-microvolt = <1150000>;
 819                                 regulator-boot-on;
 820                                 regulator-state-mem {
 821                                         regulator-off-in-suspend;
 822                                 };
 823                         };
 824
 825                         buck5_reg: BUCK5 {
 826                                 regulator-name = "VMEM_1.2V_AP";
 827                                 regulator-min-microvolt = <1200000>;
 828                                 regulator-max-microvolt = <1200000>;
 829                                 regulator-always-on;
 830                         };
 831
 832                         buck6_reg: BUCK6 {
 833                                 regulator-name = "VCC_SUB_1.35V";
 834                                 regulator-min-microvolt = <1350000>;
 835                                 regulator-max-microvolt = <1350000>;
 836                                 regulator-always-on;
 837                         };
 838
 839                         buck7_reg: BUCK7 {
 840                                 regulator-name = "VCC_SUB_2.0V";
 841                                 regulator-min-microvolt = <2000000>;
 842                                 regulator-max-microvolt = <2000000>;
 843                                 regulator-always-on;
 844                         };
 845
 846                         buck8_reg: BUCK8 {
 847                                 regulator-name = "VMEM_VDDF_3.0V";
 848                                 regulator-min-microvolt = <2850000>;
 849                                 regulator-max-microvolt = <2850000>;
 850                                 maxim,ena-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>;
 851                         };
 852
 853                         buck9_reg: BUCK9 {
 854                                 regulator-name = "CAM_ISP_CORE_1.2V";
 855                                 regulator-min-microvolt = <1000000>;
 856                                 regulator-max-microvolt = <1200000>;
 857                         };
 858                 };
 859         };
 860 };
 861
 862 &i2c_8 {
 863         status = "okay";
 864 };
 865
 866 &i2s0 {
 867         pinctrl-0 = <&i2s0_bus>;
 868         pinctrl-names = "default";
 869         status = "okay";
 870 };
 871
 872 &mixer {
 873         status = "okay";
 874 };
 875
 876 &mshc_0 {
 877         broken-cd;
 878         non-removable;
 879         card-detect-delay = <200>;
 880         vmmc-supply = <&ldo22_reg>;
 881         clock-frequency = <400000000>;
 882         samsung,dw-mshc-ciu-div = <0>;
 883         samsung,dw-mshc-sdr-timing = <2 3>;
 884         samsung,dw-mshc-ddr-timing = <1 2>;
 885         pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>;
 886         pinctrl-names = "default";
 887         status = "okay";
 888         bus-width = <8>;
 889         cap-mmc-highspeed;
 890 };
 891
 892 &pmu_system_controller {
 893         assigned-clocks = <&pmu_system_controller 0>;
 894         assigned-clock-parents =  <&clock CLK_XUSBXTI>;
 895 };
 896
 897 &pinctrl_0 {
 898         pinctrl-names = "default";
 899         pinctrl-0 = <&sleep0>;
 900
 901         mhl_int: mhl-int {
 902                 samsung,pins = "gpf3-5";
 903                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 904         };
 905
 906         i2c_mhl_bus: i2c-mhl-bus {
 907                 samsung,pins = "gpf0-4", "gpf0-6";
 908                 samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 909                 samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
 910                 samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 911         };
 912
 913         sleep0: sleep-states {
 914                 PIN_SLP(gpa0-0, INPUT, NONE);
 915                 PIN_SLP(gpa0-1, OUT0, NONE);
 916                 PIN_SLP(gpa0-2, INPUT, NONE);
 917                 PIN_SLP(gpa0-3, INPUT, UP);
 918                 PIN_SLP(gpa0-4, INPUT, NONE);
 919                 PIN_SLP(gpa0-5, INPUT, DOWN);
 920                 PIN_SLP(gpa0-6, INPUT, DOWN);
 921                 PIN_SLP(gpa0-7, INPUT, UP);
 922
 923                 PIN_SLP(gpa1-0, INPUT, DOWN);
 924                 PIN_SLP(gpa1-1, INPUT, DOWN);
 925                 PIN_SLP(gpa1-2, INPUT, DOWN);
 926                 PIN_SLP(gpa1-3, INPUT, DOWN);
 927                 PIN_SLP(gpa1-4, INPUT, DOWN);
 928                 PIN_SLP(gpa1-5, INPUT, DOWN);
 929
 930                 PIN_SLP(gpb-0, INPUT, NONE);
 931                 PIN_SLP(gpb-1, INPUT, NONE);
 932                 PIN_SLP(gpb-2, INPUT, NONE);
 933                 PIN_SLP(gpb-3, INPUT, NONE);
 934                 PIN_SLP(gpb-4, INPUT, DOWN);
 935                 PIN_SLP(gpb-5, INPUT, UP);
 936                 PIN_SLP(gpb-6, INPUT, DOWN);
 937                 PIN_SLP(gpb-7, INPUT, DOWN);
 938
 939                 PIN_SLP(gpc0-0, INPUT, DOWN);
 940                 PIN_SLP(gpc0-1, INPUT, DOWN);
 941                 PIN_SLP(gpc0-2, INPUT, DOWN);
 942                 PIN_SLP(gpc0-3, INPUT, DOWN);
 943                 PIN_SLP(gpc0-4, INPUT, DOWN);
 944
 945                 PIN_SLP(gpc1-0, INPUT, NONE);
 946                 PIN_SLP(gpc1-1, PREV, NONE);
 947                 PIN_SLP(gpc1-2, INPUT, NONE);
 948                 PIN_SLP(gpc1-3, INPUT, NONE);
 949                 PIN_SLP(gpc1-4, INPUT, NONE);
 950
 951                 PIN_SLP(gpd0-0, INPUT, DOWN);
 952                 PIN_SLP(gpd0-1, INPUT, DOWN);
 953                 PIN_SLP(gpd0-2, INPUT, NONE);
 954                 PIN_SLP(gpd0-3, INPUT, NONE);
 955
 956                 PIN_SLP(gpd1-0, INPUT, DOWN);
 957                 PIN_SLP(gpd1-1, INPUT, DOWN);
 958                 PIN_SLP(gpd1-2, INPUT, NONE);
 959                 PIN_SLP(gpd1-3, INPUT, NONE);
 960
 961                 PIN_SLP(gpf0-0, INPUT, NONE);
 962                 PIN_SLP(gpf0-1, INPUT, NONE);
 963                 PIN_SLP(gpf0-2, INPUT, DOWN);
 964                 PIN_SLP(gpf0-3, INPUT, DOWN);
 965                 PIN_SLP(gpf0-4, INPUT, NONE);
 966                 PIN_SLP(gpf0-5, INPUT, DOWN);
 967                 PIN_SLP(gpf0-6, INPUT, NONE);
 968                 PIN_SLP(gpf0-7, INPUT, DOWN);
 969
 970                 PIN_SLP(gpf1-0, INPUT, DOWN);
 971                 PIN_SLP(gpf1-1, INPUT, DOWN);
 972                 PIN_SLP(gpf1-2, INPUT, DOWN);
 973                 PIN_SLP(gpf1-3, INPUT, DOWN);
 974                 PIN_SLP(gpf1-4, INPUT, NONE);
 975                 PIN_SLP(gpf1-5, INPUT, NONE);
 976                 PIN_SLP(gpf1-6, INPUT, DOWN);
 977                 PIN_SLP(gpf1-7, PREV, NONE);
 978
 979                 PIN_SLP(gpf2-0, PREV, NONE);
 980                 PIN_SLP(gpf2-1, INPUT, DOWN);
 981                 PIN_SLP(gpf2-2, INPUT, DOWN);
 982                 PIN_SLP(gpf2-3, INPUT, DOWN);
 983                 PIN_SLP(gpf2-4, INPUT, DOWN);
 984                 PIN_SLP(gpf2-5, INPUT, DOWN);
 985                 PIN_SLP(gpf2-6, INPUT, NONE);
 986                 PIN_SLP(gpf2-7, INPUT, NONE);
 987
 988                 PIN_SLP(gpf3-0, INPUT, NONE);
 989                 PIN_SLP(gpf3-1, PREV, NONE);
 990                 PIN_SLP(gpf3-2, PREV, NONE);
 991                 PIN_SLP(gpf3-3, PREV, NONE);
 992                 PIN_SLP(gpf3-4, OUT1, NONE);
 993                 PIN_SLP(gpf3-5, INPUT, DOWN);
 994
 995                 PIN_SLP(gpj0-0, PREV, NONE);
 996                 PIN_SLP(gpj0-1, PREV, NONE);
 997                 PIN_SLP(gpj0-2, PREV, NONE);
 998                 PIN_SLP(gpj0-3, INPUT, DOWN);
 999                 PIN_SLP(gpj0-4, PREV, NONE);
1000                 PIN_SLP(gpj0-5, PREV, NONE);
1001                 PIN_SLP(gpj0-6, INPUT, DOWN);
1002                 PIN_SLP(gpj0-7, INPUT, DOWN);
1003
1004                 PIN_SLP(gpj1-0, INPUT, DOWN);
1005                 PIN_SLP(gpj1-1, PREV, NONE);
1006                 PIN_SLP(gpj1-2, PREV, NONE);
1007                 PIN_SLP(gpj1-3, INPUT, DOWN);
1008                 PIN_SLP(gpj1-4, INPUT, DOWN);
1009         };
1010 };
1011
1012 &pinctrl_1 {
1013         pinctrl-names = "default";
1014         pinctrl-0 = <&sleep1>;
1015
1016         hdmi_hpd: hdmi-hpd {
1017                 samsung,pins = "gpx3-7";
1018                 samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
1019         };
1020
1021         sleep1: sleep-states {
1022                 PIN_SLP(gpk0-0, PREV, NONE);
1023                 PIN_SLP(gpk0-1, PREV, NONE);
1024                 PIN_SLP(gpk0-2, OUT0, NONE);
1025                 PIN_SLP(gpk0-3, PREV, NONE);
1026                 PIN_SLP(gpk0-4, PREV, NONE);
1027                 PIN_SLP(gpk0-5, PREV, NONE);
1028                 PIN_SLP(gpk0-6, PREV, NONE);
1029
1030                 PIN_SLP(gpk1-0, INPUT, DOWN);
1031                 PIN_SLP(gpk1-1, INPUT, DOWN);
1032                 PIN_SLP(gpk1-2, INPUT, DOWN);
1033                 PIN_SLP(gpk1-3, PREV, NONE);
1034                 PIN_SLP(gpk1-4, PREV, NONE);
1035                 PIN_SLP(gpk1-5, PREV, NONE);
1036                 PIN_SLP(gpk1-6, PREV, NONE);
1037
1038                 PIN_SLP(gpk2-0, INPUT, DOWN);
1039                 PIN_SLP(gpk2-1, INPUT, DOWN);
1040                 PIN_SLP(gpk2-2, INPUT, DOWN);
1041                 PIN_SLP(gpk2-3, INPUT, DOWN);
1042                 PIN_SLP(gpk2-4, INPUT, DOWN);
1043                 PIN_SLP(gpk2-5, INPUT, DOWN);
1044                 PIN_SLP(gpk2-6, INPUT, DOWN);
1045
1046                 PIN_SLP(gpk3-0, OUT0, NONE);
1047                 PIN_SLP(gpk3-1, INPUT, NONE);
1048                 PIN_SLP(gpk3-2, INPUT, DOWN);
1049                 PIN_SLP(gpk3-3, INPUT, NONE);
1050                 PIN_SLP(gpk3-4, INPUT, NONE);
1051                 PIN_SLP(gpk3-5, INPUT, NONE);
1052                 PIN_SLP(gpk3-6, INPUT, NONE);
1053
1054                 PIN_SLP(gpl0-0, INPUT, DOWN);
1055                 PIN_SLP(gpl0-1, INPUT, DOWN);
1056                 PIN_SLP(gpl0-2, INPUT, DOWN);
1057                 PIN_SLP(gpl0-3, INPUT, DOWN);
1058                 PIN_SLP(gpl0-4, PREV, NONE);
1059                 PIN_SLP(gpl0-6, PREV, NONE);
1060
1061                 PIN_SLP(gpl1-0, INPUT, DOWN);
1062                 PIN_SLP(gpl1-1, INPUT, DOWN);
1063                 PIN_SLP(gpl2-0, INPUT, DOWN);
1064                 PIN_SLP(gpl2-1, INPUT, DOWN);
1065                 PIN_SLP(gpl2-2, INPUT, DOWN);
1066                 PIN_SLP(gpl2-3, INPUT, DOWN);
1067                 PIN_SLP(gpl2-4, INPUT, DOWN);
1068                 PIN_SLP(gpl2-5, INPUT, DOWN);
1069                 PIN_SLP(gpl2-6, PREV, NONE);
1070                 PIN_SLP(gpl2-7, INPUT, DOWN);
1071
1072                 PIN_SLP(gpm0-0, INPUT, DOWN);
1073                 PIN_SLP(gpm0-1, INPUT, DOWN);
1074                 PIN_SLP(gpm0-2, INPUT, DOWN);
1075                 PIN_SLP(gpm0-3, INPUT, DOWN);
1076                 PIN_SLP(gpm0-4, INPUT, DOWN);
1077                 PIN_SLP(gpm0-5, INPUT, DOWN);
1078                 PIN_SLP(gpm0-6, INPUT, DOWN);
1079                 PIN_SLP(gpm0-7, INPUT, DOWN);
1080
1081                 PIN_SLP(gpm1-0, INPUT, DOWN);
1082                 PIN_SLP(gpm1-1, INPUT, DOWN);
1083                 PIN_SLP(gpm1-2, INPUT, NONE);
1084                 PIN_SLP(gpm1-3, INPUT, NONE);
1085                 PIN_SLP(gpm1-4, INPUT, NONE);
1086                 PIN_SLP(gpm1-5, INPUT, NONE);
1087                 PIN_SLP(gpm1-6, INPUT, DOWN);
1088
1089                 PIN_SLP(gpm2-0, INPUT, NONE);
1090                 PIN_SLP(gpm2-1, INPUT, NONE);
1091                 PIN_SLP(gpm2-2, INPUT, DOWN);
1092                 PIN_SLP(gpm2-3, INPUT, DOWN);
1093                 PIN_SLP(gpm2-4, INPUT, DOWN);
1094
1095                 PIN_SLP(gpm3-0, PREV, NONE);
1096                 PIN_SLP(gpm3-1, PREV, NONE);
1097                 PIN_SLP(gpm3-2, PREV, NONE);
1098                 PIN_SLP(gpm3-3, OUT1, NONE);
1099                 PIN_SLP(gpm3-4, INPUT, DOWN);
1100                 PIN_SLP(gpm3-5, INPUT, DOWN);
1101                 PIN_SLP(gpm3-6, INPUT, DOWN);
1102                 PIN_SLP(gpm3-7, INPUT, DOWN);
1103
1104                 PIN_SLP(gpm4-0, INPUT, DOWN);
1105                 PIN_SLP(gpm4-1, INPUT, DOWN);
1106                 PIN_SLP(gpm4-2, INPUT, DOWN);
1107                 PIN_SLP(gpm4-3, INPUT, DOWN);
1108                 PIN_SLP(gpm4-4, INPUT, DOWN);
1109                 PIN_SLP(gpm4-5, INPUT, DOWN);
1110                 PIN_SLP(gpm4-6, INPUT, DOWN);
1111                 PIN_SLP(gpm4-7, INPUT, DOWN);
1112
1113                 PIN_SLP(gpy0-0, INPUT, DOWN);
1114                 PIN_SLP(gpy0-1, INPUT, DOWN);
1115                 PIN_SLP(gpy0-2, INPUT, DOWN);
1116                 PIN_SLP(gpy0-3, INPUT, DOWN);
1117                 PIN_SLP(gpy0-4, INPUT, DOWN);
1118                 PIN_SLP(gpy0-5, INPUT, DOWN);
1119
1120                 PIN_SLP(gpy1-0, INPUT, DOWN);
1121                 PIN_SLP(gpy1-1, INPUT, DOWN);
1122                 PIN_SLP(gpy1-2, INPUT, DOWN);
1123                 PIN_SLP(gpy1-3, INPUT, DOWN);
1124
1125                 PIN_SLP(gpy2-0, PREV, NONE);
1126                 PIN_SLP(gpy2-1, INPUT, DOWN);
1127                 PIN_SLP(gpy2-2, INPUT, NONE);
1128                 PIN_SLP(gpy2-3, INPUT, NONE);
1129                 PIN_SLP(gpy2-4, INPUT, NONE);
1130                 PIN_SLP(gpy2-5, INPUT, NONE);
1131
1132                 PIN_SLP(gpy3-0, INPUT, DOWN);
1133                 PIN_SLP(gpy3-1, INPUT, DOWN);
1134                 PIN_SLP(gpy3-2, INPUT, DOWN);
1135                 PIN_SLP(gpy3-3, INPUT, DOWN);
1136                 PIN_SLP(gpy3-4, INPUT, DOWN);
1137                 PIN_SLP(gpy3-5, INPUT, DOWN);
1138                 PIN_SLP(gpy3-6, INPUT, DOWN);
1139                 PIN_SLP(gpy3-7, INPUT, DOWN);
1140
1141                 PIN_SLP(gpy4-0, INPUT, DOWN);
1142                 PIN_SLP(gpy4-1, INPUT, DOWN);
1143                 PIN_SLP(gpy4-2, INPUT, DOWN);
1144                 PIN_SLP(gpy4-3, INPUT, DOWN);
1145                 PIN_SLP(gpy4-4, INPUT, DOWN);
1146                 PIN_SLP(gpy4-5, INPUT, DOWN);
1147                 PIN_SLP(gpy4-6, INPUT, DOWN);
1148                 PIN_SLP(gpy4-7, INPUT, DOWN);
1149
1150                 PIN_SLP(gpy5-0, INPUT, DOWN);
1151                 PIN_SLP(gpy5-1, INPUT, DOWN);
1152                 PIN_SLP(gpy5-2, INPUT, DOWN);
1153                 PIN_SLP(gpy5-3, INPUT, DOWN);
1154                 PIN_SLP(gpy5-4, INPUT, DOWN);
1155                 PIN_SLP(gpy5-5, INPUT, DOWN);
1156                 PIN_SLP(gpy5-6, INPUT, DOWN);
1157                 PIN_SLP(gpy5-7, INPUT, DOWN);
1158
1159                 PIN_SLP(gpy6-0, INPUT, DOWN);
1160                 PIN_SLP(gpy6-1, INPUT, DOWN);
1161                 PIN_SLP(gpy6-2, INPUT, DOWN);
1162                 PIN_SLP(gpy6-3, INPUT, DOWN);
1163                 PIN_SLP(gpy6-4, INPUT, DOWN);
1164                 PIN_SLP(gpy6-5, INPUT, DOWN);
1165                 PIN_SLP(gpy6-6, INPUT, DOWN);
1166                 PIN_SLP(gpy6-7, INPUT, DOWN);
1167         };
1168 };
1169
1170 &pinctrl_2 {
1171         pinctrl-names = "default";
1172         pinctrl-0 = <&sleep2>;
1173
1174         sleep2: sleep-states {
1175                 PIN_SLP(gpz-0, INPUT, DOWN);
1176                 PIN_SLP(gpz-1, INPUT, DOWN);
1177                 PIN_SLP(gpz-2, INPUT, DOWN);
1178                 PIN_SLP(gpz-3, INPUT, DOWN);
1179                 PIN_SLP(gpz-4, INPUT, DOWN);
1180                 PIN_SLP(gpz-5, INPUT, DOWN);
1181                 PIN_SLP(gpz-6, INPUT, DOWN);
1182         };
1183 };
1184
1185 &pinctrl_3 {
1186         pinctrl-names = "default";
1187         pinctrl-0 = <&sleep3>;
1188
1189         sleep3: sleep-states {
1190                 PIN_SLP(gpv0-0, INPUT, DOWN);
1191                 PIN_SLP(gpv0-1, INPUT, DOWN);
1192                 PIN_SLP(gpv0-2, INPUT, DOWN);
1193                 PIN_SLP(gpv0-3, INPUT, DOWN);
1194                 PIN_SLP(gpv0-4, INPUT, DOWN);
1195                 PIN_SLP(gpv0-5, INPUT, DOWN);
1196                 PIN_SLP(gpv0-6, INPUT, DOWN);
1197                 PIN_SLP(gpv0-7, INPUT, DOWN);
1198
1199                 PIN_SLP(gpv1-0, INPUT, DOWN);
1200                 PIN_SLP(gpv1-1, INPUT, DOWN);
1201                 PIN_SLP(gpv1-2, INPUT, DOWN);
1202                 PIN_SLP(gpv1-3, INPUT, DOWN);
1203                 PIN_SLP(gpv1-4, INPUT, DOWN);
1204                 PIN_SLP(gpv1-5, INPUT, DOWN);
1205                 PIN_SLP(gpv1-6, INPUT, DOWN);
1206                 PIN_SLP(gpv1-7, INPUT, DOWN);
1207
1208                 PIN_SLP(gpv2-0, INPUT, DOWN);
1209                 PIN_SLP(gpv2-1, INPUT, DOWN);
1210                 PIN_SLP(gpv2-2, INPUT, DOWN);
1211                 PIN_SLP(gpv2-3, INPUT, DOWN);
1212                 PIN_SLP(gpv2-4, INPUT, DOWN);
1213                 PIN_SLP(gpv2-5, INPUT, DOWN);
1214                 PIN_SLP(gpv2-6, INPUT, DOWN);
1215                 PIN_SLP(gpv2-7, INPUT, DOWN);
1216
1217                 PIN_SLP(gpv3-0, INPUT, DOWN);
1218                 PIN_SLP(gpv3-1, INPUT, DOWN);
1219                 PIN_SLP(gpv3-2, INPUT, DOWN);
1220                 PIN_SLP(gpv3-3, INPUT, DOWN);
1221                 PIN_SLP(gpv3-4, INPUT, DOWN);
1222                 PIN_SLP(gpv3-5, INPUT, DOWN);
1223                 PIN_SLP(gpv3-6, INPUT, DOWN);
1224                 PIN_SLP(gpv3-7, INPUT, DOWN);
1225
1226                 PIN_SLP(gpv4-0, INPUT, DOWN);
1227         };
1228 };
1229
1230 &pwm {
1231         pinctrl-0 = <&pwm0_out>;
1232         pinctrl-names = "default";
1233         samsung,pwm-outputs = <0>;
1234         status = "okay";
1235 };
1236
1237 &rtc {
1238         status = "okay";
1239         clocks = <&clock CLK_RTC>, <&max77686 MAX77686_CLK_AP>;
1240         clock-names = "rtc", "rtc_src";
1241 };
1242
1243 &sdhci_2 {
1244         bus-width = <4>;
1245         cd-gpios = <&gpx3 4 GPIO_ACTIVE_HIGH>;
1246         cd-inverted;
1247         pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4>;
1248         pinctrl-names = "default";
1249         vmmc-supply = <&ldo21_reg>;
1250         status = "okay";
1251 };
1252
1253 &sdhci_3 {
1254         #address-cells = <1>;
1255         #size-cells = <0>;
1256         non-removable;
1257         bus-width = <4>;
1258
1259         mmc-pwrseq = <&wlan_pwrseq>;
1260         pinctrl-names = "default";
1261         pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_bus4>;
1262         status = "okay";
1263
1264         brcmf: wifi@1 {
1265                 reg = <1>;
1266                 compatible = "brcm,bcm4329-fmac";
1267                 interrupt-parent = <&gpx2>;
1268                 interrupts = <5 IRQ_TYPE_NONE>;
1269                 interrupt-names = "host-wake";
1270         };
1271 };
1272
1273 &serial_0 {
1274         status = "okay";
1275 };
1276
1277 &serial_1 {
1278         status = "okay";
1279 };
1280
1281 &serial_2 {
1282         status = "okay";
1283 };
1284
1285 &serial_3 {
1286         status = "okay";
1287 };
1288
1289 &spi_1 {
1290         pinctrl-names = "default";
1291         pinctrl-0 = <&spi1_bus>;
1292         cs-gpios = <&gpb 5 GPIO_ACTIVE_HIGH>;
1293         status = "okay";
1294
1295         s5c73m3_spi: s5c73m3@0 {
1296                 compatible = "samsung,s5c73m3";
1297                 spi-max-frequency = <50000000>;
1298                 reg = <0>;
1299                 controller-data {
1300                         samsung,spi-feedback-delay = <2>;
1301                 };
1302         };
1303 };
1304
1305 &tmu {
1306         vtmu-supply = <&ldo10_reg>;
1307         status = "okay";
1308 };